1 /* 2 * Driver for DBRI sound chip found on Sparcs. 3 * Copyright (C) 2004, 2005 Martin Habets (mhabets@users.sourceforge.net) 4 * 5 * Converted to ring buffered version by Krzysztof Helt (krzysztof.h1@wp.pl) 6 * 7 * Based entirely upon drivers/sbus/audio/dbri.c which is: 8 * Copyright (C) 1997 Rudolf Koenig (rfkoenig@immd4.informatik.uni-erlangen.de) 9 * Copyright (C) 1998, 1999 Brent Baccala (baccala@freesoft.org) 10 * 11 * This is the low level driver for the DBRI & MMCODEC duo used for ISDN & AUDIO 12 * on Sun SPARCStation 10, 20, LX and Voyager models. 13 * 14 * - DBRI: AT&T T5900FX Dual Basic Rates ISDN Interface. It is a 32 channel 15 * data time multiplexer with ISDN support (aka T7259) 16 * Interfaces: SBus,ISDN NT & TE, CHI, 4 bits parallel. 17 * CHI: (spelled ki) Concentration Highway Interface (AT&T or Intel bus ?). 18 * Documentation: 19 * - "STP 4000SBus Dual Basic Rate ISDN (DBRI) Transceiver" from 20 * Sparc Technology Business (courtesy of Sun Support) 21 * - Data sheet of the T7903, a newer but very similar ISA bus equivalent 22 * available from the Lucent (formerly AT&T microelectronics) home 23 * page. 24 * - http://www.freesoft.org/Linux/DBRI/ 25 * - MMCODEC: Crystal Semiconductor CS4215 16 bit Multimedia Audio Codec 26 * Interfaces: CHI, Audio In & Out, 2 bits parallel 27 * Documentation: from the Crystal Semiconductor home page. 28 * 29 * The DBRI is a 32 pipe machine, each pipe can transfer some bits between 30 * memory and a serial device (long pipes, no. 0-15) or between two serial 31 * devices (short pipes, no. 16-31), or simply send a fixed data to a serial 32 * device (short pipes). 33 * A timeslot defines the bit-offset and no. of bits read from a serial device. 34 * The timeslots are linked to 6 circular lists, one for each direction for 35 * each serial device (NT,TE,CHI). A timeslot is associated to 1 or 2 pipes 36 * (the second one is a monitor/tee pipe, valid only for serial input). 37 * 38 * The mmcodec is connected via the CHI bus and needs the data & some 39 * parameters (volume, output selection) time multiplexed in 8 byte 40 * chunks. It also has a control mode, which serves for audio format setting. 41 * 42 * Looking at the CS4215 data sheet it is easy to set up 2 or 4 codecs on 43 * the same CHI bus, so I thought perhaps it is possible to use the on-board 44 * & the speakerbox codec simultaneously, giving 2 (not very independent :-) 45 * audio devices. But the SUN HW group decided against it, at least on my 46 * LX the speakerbox connector has at least 1 pin missing and 1 wrongly 47 * connected. 48 * 49 * I've tried to stick to the following function naming conventions: 50 * snd_* ALSA stuff 51 * cs4215_* CS4215 codec specific stuff 52 * dbri_* DBRI high-level stuff 53 * other DBRI low-level stuff 54 */ 55 56 #include <linux/interrupt.h> 57 #include <linux/delay.h> 58 #include <linux/irq.h> 59 #include <linux/io.h> 60 #include <linux/dma-mapping.h> 61 62 #include <sound/core.h> 63 #include <sound/pcm.h> 64 #include <sound/pcm_params.h> 65 #include <sound/info.h> 66 #include <sound/control.h> 67 #include <sound/initval.h> 68 69 #include <linux/of.h> 70 #include <linux/of_device.h> 71 #include <asm/atomic.h> 72 73 MODULE_AUTHOR("Rudolf Koenig, Brent Baccala and Martin Habets"); 74 MODULE_DESCRIPTION("Sun DBRI"); 75 MODULE_LICENSE("GPL"); 76 MODULE_SUPPORTED_DEVICE("{{Sun,DBRI}}"); 77 78 static int index[SNDRV_CARDS] = SNDRV_DEFAULT_IDX; /* Index 0-MAX */ 79 static char *id[SNDRV_CARDS] = SNDRV_DEFAULT_STR; /* ID for this card */ 80 /* Enable this card */ 81 static int enable[SNDRV_CARDS] = SNDRV_DEFAULT_ENABLE_PNP; 82 83 module_param_array(index, int, NULL, 0444); 84 MODULE_PARM_DESC(index, "Index value for Sun DBRI soundcard."); 85 module_param_array(id, charp, NULL, 0444); 86 MODULE_PARM_DESC(id, "ID string for Sun DBRI soundcard."); 87 module_param_array(enable, bool, NULL, 0444); 88 MODULE_PARM_DESC(enable, "Enable Sun DBRI soundcard."); 89 90 #undef DBRI_DEBUG 91 92 #define D_INT (1<<0) 93 #define D_GEN (1<<1) 94 #define D_CMD (1<<2) 95 #define D_MM (1<<3) 96 #define D_USR (1<<4) 97 #define D_DESC (1<<5) 98 99 static int dbri_debug; 100 module_param(dbri_debug, int, 0644); 101 MODULE_PARM_DESC(dbri_debug, "Debug value for Sun DBRI soundcard."); 102 103 #ifdef DBRI_DEBUG 104 static char *cmds[] = { 105 "WAIT", "PAUSE", "JUMP", "IIQ", "REX", "SDP", "CDP", "DTS", 106 "SSP", "CHI", "NT", "TE", "CDEC", "TEST", "CDM", "RESRV" 107 }; 108 109 #define dprintk(a, x...) if (dbri_debug & a) printk(KERN_DEBUG x) 110 111 #else 112 #define dprintk(a, x...) do { } while (0) 113 114 #endif /* DBRI_DEBUG */ 115 116 #define DBRI_CMD(cmd, intr, value) ((cmd << 28) | \ 117 (intr << 27) | \ 118 value) 119 120 /*************************************************************************** 121 CS4215 specific definitions and structures 122 ****************************************************************************/ 123 124 struct cs4215 { 125 __u8 data[4]; /* Data mode: Time slots 5-8 */ 126 __u8 ctrl[4]; /* Ctrl mode: Time slots 1-4 */ 127 __u8 onboard; 128 __u8 offset; /* Bit offset from frame sync to time slot 1 */ 129 volatile __u32 status; 130 volatile __u32 version; 131 __u8 precision; /* In bits, either 8 or 16 */ 132 __u8 channels; /* 1 or 2 */ 133 }; 134 135 /* 136 * Control mode first 137 */ 138 139 /* Time Slot 1, Status register */ 140 #define CS4215_CLB (1<<2) /* Control Latch Bit */ 141 #define CS4215_OLB (1<<3) /* 1: line: 2.0V, speaker 4V */ 142 /* 0: line: 2.8V, speaker 8V */ 143 #define CS4215_MLB (1<<4) /* 1: Microphone: 20dB gain disabled */ 144 #define CS4215_RSRVD_1 (1<<5) 145 146 /* Time Slot 2, Data Format Register */ 147 #define CS4215_DFR_LINEAR16 0 148 #define CS4215_DFR_ULAW 1 149 #define CS4215_DFR_ALAW 2 150 #define CS4215_DFR_LINEAR8 3 151 #define CS4215_DFR_STEREO (1<<2) 152 static struct { 153 unsigned short freq; 154 unsigned char xtal; 155 unsigned char csval; 156 } CS4215_FREQ[] = { 157 { 8000, (1 << 4), (0 << 3) }, 158 { 16000, (1 << 4), (1 << 3) }, 159 { 27429, (1 << 4), (2 << 3) }, /* Actually 24428.57 */ 160 { 32000, (1 << 4), (3 << 3) }, 161 /* { NA, (1 << 4), (4 << 3) }, */ 162 /* { NA, (1 << 4), (5 << 3) }, */ 163 { 48000, (1 << 4), (6 << 3) }, 164 { 9600, (1 << 4), (7 << 3) }, 165 { 5512, (2 << 4), (0 << 3) }, /* Actually 5512.5 */ 166 { 11025, (2 << 4), (1 << 3) }, 167 { 18900, (2 << 4), (2 << 3) }, 168 { 22050, (2 << 4), (3 << 3) }, 169 { 37800, (2 << 4), (4 << 3) }, 170 { 44100, (2 << 4), (5 << 3) }, 171 { 33075, (2 << 4), (6 << 3) }, 172 { 6615, (2 << 4), (7 << 3) }, 173 { 0, 0, 0} 174 }; 175 176 #define CS4215_HPF (1<<7) /* High Pass Filter, 1: Enabled */ 177 178 #define CS4215_12_MASK 0xfcbf /* Mask off reserved bits in slot 1 & 2 */ 179 180 /* Time Slot 3, Serial Port Control register */ 181 #define CS4215_XEN (1<<0) /* 0: Enable serial output */ 182 #define CS4215_XCLK (1<<1) /* 1: Master mode: Generate SCLK */ 183 #define CS4215_BSEL_64 (0<<2) /* Bitrate: 64 bits per frame */ 184 #define CS4215_BSEL_128 (1<<2) 185 #define CS4215_BSEL_256 (2<<2) 186 #define CS4215_MCK_MAST (0<<4) /* Master clock */ 187 #define CS4215_MCK_XTL1 (1<<4) /* 24.576 MHz clock source */ 188 #define CS4215_MCK_XTL2 (2<<4) /* 16.9344 MHz clock source */ 189 #define CS4215_MCK_CLK1 (3<<4) /* Clockin, 256 x Fs */ 190 #define CS4215_MCK_CLK2 (4<<4) /* Clockin, see DFR */ 191 192 /* Time Slot 4, Test Register */ 193 #define CS4215_DAD (1<<0) /* 0:Digital-Dig loop, 1:Dig-Analog-Dig loop */ 194 #define CS4215_ENL (1<<1) /* Enable Loopback Testing */ 195 196 /* Time Slot 5, Parallel Port Register */ 197 /* Read only here and the same as the in data mode */ 198 199 /* Time Slot 6, Reserved */ 200 201 /* Time Slot 7, Version Register */ 202 #define CS4215_VERSION_MASK 0xf /* Known versions 0/C, 1/D, 2/E */ 203 204 /* Time Slot 8, Reserved */ 205 206 /* 207 * Data mode 208 */ 209 /* Time Slot 1-2: Left Channel Data, 2-3: Right Channel Data */ 210 211 /* Time Slot 5, Output Setting */ 212 #define CS4215_LO(v) v /* Left Output Attenuation 0x3f: -94.5 dB */ 213 #define CS4215_LE (1<<6) /* Line Out Enable */ 214 #define CS4215_HE (1<<7) /* Headphone Enable */ 215 216 /* Time Slot 6, Output Setting */ 217 #define CS4215_RO(v) v /* Right Output Attenuation 0x3f: -94.5 dB */ 218 #define CS4215_SE (1<<6) /* Speaker Enable */ 219 #define CS4215_ADI (1<<7) /* A/D Data Invalid: Busy in calibration */ 220 221 /* Time Slot 7, Input Setting */ 222 #define CS4215_LG(v) v /* Left Gain Setting 0xf: 22.5 dB */ 223 #define CS4215_IS (1<<4) /* Input Select: 1=Microphone, 0=Line */ 224 #define CS4215_OVR (1<<5) /* 1: Over range condition occurred */ 225 #define CS4215_PIO0 (1<<6) /* Parallel I/O 0 */ 226 #define CS4215_PIO1 (1<<7) 227 228 /* Time Slot 8, Input Setting */ 229 #define CS4215_RG(v) v /* Right Gain Setting 0xf: 22.5 dB */ 230 #define CS4215_MA(v) (v<<4) /* Monitor Path Attenuation 0xf: mute */ 231 232 /*************************************************************************** 233 DBRI specific definitions and structures 234 ****************************************************************************/ 235 236 /* DBRI main registers */ 237 #define REG0 0x00 /* Status and Control */ 238 #define REG1 0x04 /* Mode and Interrupt */ 239 #define REG2 0x08 /* Parallel IO */ 240 #define REG3 0x0c /* Test */ 241 #define REG8 0x20 /* Command Queue Pointer */ 242 #define REG9 0x24 /* Interrupt Queue Pointer */ 243 244 #define DBRI_NO_CMDS 64 245 #define DBRI_INT_BLK 64 246 #define DBRI_NO_DESCS 64 247 #define DBRI_NO_PIPES 32 248 #define DBRI_MAX_PIPE (DBRI_NO_PIPES - 1) 249 250 #define DBRI_REC 0 251 #define DBRI_PLAY 1 252 #define DBRI_NO_STREAMS 2 253 254 /* One transmit/receive descriptor */ 255 /* When ba != 0 descriptor is used */ 256 struct dbri_mem { 257 volatile __u32 word1; 258 __u32 ba; /* Transmit/Receive Buffer Address */ 259 __u32 nda; /* Next Descriptor Address */ 260 volatile __u32 word4; 261 }; 262 263 /* This structure is in a DMA region where it can accessed by both 264 * the CPU and the DBRI 265 */ 266 struct dbri_dma { 267 s32 cmd[DBRI_NO_CMDS]; /* Place for commands */ 268 volatile s32 intr[DBRI_INT_BLK]; /* Interrupt field */ 269 struct dbri_mem desc[DBRI_NO_DESCS]; /* Xmit/receive descriptors */ 270 }; 271 272 #define dbri_dma_off(member, elem) \ 273 ((u32)(unsigned long) \ 274 (&(((struct dbri_dma *)0)->member[elem]))) 275 276 enum in_or_out { PIPEinput, PIPEoutput }; 277 278 struct dbri_pipe { 279 u32 sdp; /* SDP command word */ 280 int nextpipe; /* Next pipe in linked list */ 281 int length; /* Length of timeslot (bits) */ 282 int first_desc; /* Index of first descriptor */ 283 int desc; /* Index of active descriptor */ 284 volatile __u32 *recv_fixed_ptr; /* Ptr to receive fixed data */ 285 }; 286 287 /* Per stream (playback or record) information */ 288 struct dbri_streaminfo { 289 struct snd_pcm_substream *substream; 290 u32 dvma_buffer; /* Device view of ALSA DMA buffer */ 291 int size; /* Size of DMA buffer */ 292 size_t offset; /* offset in user buffer */ 293 int pipe; /* Data pipe used */ 294 int left_gain; /* mixer elements */ 295 int right_gain; 296 }; 297 298 /* This structure holds the information for both chips (DBRI & CS4215) */ 299 struct snd_dbri { 300 int regs_size, irq; /* Needed for unload */ 301 struct of_device *op; /* OF device info */ 302 spinlock_t lock; 303 304 struct dbri_dma *dma; /* Pointer to our DMA block */ 305 u32 dma_dvma; /* DBRI visible DMA address */ 306 307 void __iomem *regs; /* dbri HW regs */ 308 int dbri_irqp; /* intr queue pointer */ 309 310 struct dbri_pipe pipes[DBRI_NO_PIPES]; /* DBRI's 32 data pipes */ 311 int next_desc[DBRI_NO_DESCS]; /* Index of next desc, or -1 */ 312 spinlock_t cmdlock; /* Protects cmd queue accesses */ 313 s32 *cmdptr; /* Pointer to the last queued cmd */ 314 315 int chi_bpf; 316 317 struct cs4215 mm; /* mmcodec special info */ 318 /* per stream (playback/record) info */ 319 struct dbri_streaminfo stream_info[DBRI_NO_STREAMS]; 320 }; 321 322 #define DBRI_MAX_VOLUME 63 /* Output volume */ 323 #define DBRI_MAX_GAIN 15 /* Input gain */ 324 325 /* DBRI Reg0 - Status Control Register - defines. (Page 17) */ 326 #define D_P (1<<15) /* Program command & queue pointer valid */ 327 #define D_G (1<<14) /* Allow 4-Word SBus Burst */ 328 #define D_S (1<<13) /* Allow 16-Word SBus Burst */ 329 #define D_E (1<<12) /* Allow 8-Word SBus Burst */ 330 #define D_X (1<<7) /* Sanity Timer Disable */ 331 #define D_T (1<<6) /* Permit activation of the TE interface */ 332 #define D_N (1<<5) /* Permit activation of the NT interface */ 333 #define D_C (1<<4) /* Permit activation of the CHI interface */ 334 #define D_F (1<<3) /* Force Sanity Timer Time-Out */ 335 #define D_D (1<<2) /* Disable Master Mode */ 336 #define D_H (1<<1) /* Halt for Analysis */ 337 #define D_R (1<<0) /* Soft Reset */ 338 339 /* DBRI Reg1 - Mode and Interrupt Register - defines. (Page 18) */ 340 #define D_LITTLE_END (1<<8) /* Byte Order */ 341 #define D_BIG_END (0<<8) /* Byte Order */ 342 #define D_MRR (1<<4) /* Multiple Error Ack on SBus (read only) */ 343 #define D_MLE (1<<3) /* Multiple Late Error on SBus (read only) */ 344 #define D_LBG (1<<2) /* Lost Bus Grant on SBus (read only) */ 345 #define D_MBE (1<<1) /* Burst Error on SBus (read only) */ 346 #define D_IR (1<<0) /* Interrupt Indicator (read only) */ 347 348 /* DBRI Reg2 - Parallel IO Register - defines. (Page 18) */ 349 #define D_ENPIO3 (1<<7) /* Enable Pin 3 */ 350 #define D_ENPIO2 (1<<6) /* Enable Pin 2 */ 351 #define D_ENPIO1 (1<<5) /* Enable Pin 1 */ 352 #define D_ENPIO0 (1<<4) /* Enable Pin 0 */ 353 #define D_ENPIO (0xf0) /* Enable all the pins */ 354 #define D_PIO3 (1<<3) /* Pin 3: 1: Data mode, 0: Ctrl mode */ 355 #define D_PIO2 (1<<2) /* Pin 2: 1: Onboard PDN */ 356 #define D_PIO1 (1<<1) /* Pin 1: 0: Reset */ 357 #define D_PIO0 (1<<0) /* Pin 0: 1: Speakerbox PDN */ 358 359 /* DBRI Commands (Page 20) */ 360 #define D_WAIT 0x0 /* Stop execution */ 361 #define D_PAUSE 0x1 /* Flush long pipes */ 362 #define D_JUMP 0x2 /* New command queue */ 363 #define D_IIQ 0x3 /* Initialize Interrupt Queue */ 364 #define D_REX 0x4 /* Report command execution via interrupt */ 365 #define D_SDP 0x5 /* Setup Data Pipe */ 366 #define D_CDP 0x6 /* Continue Data Pipe (reread NULL Pointer) */ 367 #define D_DTS 0x7 /* Define Time Slot */ 368 #define D_SSP 0x8 /* Set short Data Pipe */ 369 #define D_CHI 0x9 /* Set CHI Global Mode */ 370 #define D_NT 0xa /* NT Command */ 371 #define D_TE 0xb /* TE Command */ 372 #define D_CDEC 0xc /* Codec setup */ 373 #define D_TEST 0xd /* No comment */ 374 #define D_CDM 0xe /* CHI Data mode command */ 375 376 /* Special bits for some commands */ 377 #define D_PIPE(v) ((v)<<0) /* Pipe No.: 0-15 long, 16-21 short */ 378 379 /* Setup Data Pipe */ 380 /* IRM */ 381 #define D_SDP_2SAME (1<<18) /* Report 2nd time in a row value received */ 382 #define D_SDP_CHANGE (2<<18) /* Report any changes */ 383 #define D_SDP_EVERY (3<<18) /* Report any changes */ 384 #define D_SDP_EOL (1<<17) /* EOL interrupt enable */ 385 #define D_SDP_IDLE (1<<16) /* HDLC idle interrupt enable */ 386 387 /* Pipe data MODE */ 388 #define D_SDP_MEM (0<<13) /* To/from memory */ 389 #define D_SDP_HDLC (2<<13) 390 #define D_SDP_HDLC_D (3<<13) /* D Channel (prio control) */ 391 #define D_SDP_SER (4<<13) /* Serial to serial */ 392 #define D_SDP_FIXED (6<<13) /* Short only */ 393 #define D_SDP_MODE(v) ((v)&(7<<13)) 394 395 #define D_SDP_TO_SER (1<<12) /* Direction */ 396 #define D_SDP_FROM_SER (0<<12) /* Direction */ 397 #define D_SDP_MSB (1<<11) /* Bit order within Byte */ 398 #define D_SDP_LSB (0<<11) /* Bit order within Byte */ 399 #define D_SDP_P (1<<10) /* Pointer Valid */ 400 #define D_SDP_A (1<<8) /* Abort */ 401 #define D_SDP_C (1<<7) /* Clear */ 402 403 /* Define Time Slot */ 404 #define D_DTS_VI (1<<17) /* Valid Input Time-Slot Descriptor */ 405 #define D_DTS_VO (1<<16) /* Valid Output Time-Slot Descriptor */ 406 #define D_DTS_INS (1<<15) /* Insert Time Slot */ 407 #define D_DTS_DEL (0<<15) /* Delete Time Slot */ 408 #define D_DTS_PRVIN(v) ((v)<<10) /* Previous In Pipe */ 409 #define D_DTS_PRVOUT(v) ((v)<<5) /* Previous Out Pipe */ 410 411 /* Time Slot defines */ 412 #define D_TS_LEN(v) ((v)<<24) /* Number of bits in this time slot */ 413 #define D_TS_CYCLE(v) ((v)<<14) /* Bit Count at start of TS */ 414 #define D_TS_DI (1<<13) /* Data Invert */ 415 #define D_TS_1CHANNEL (0<<10) /* Single Channel / Normal mode */ 416 #define D_TS_MONITOR (2<<10) /* Monitor pipe */ 417 #define D_TS_NONCONTIG (3<<10) /* Non contiguous mode */ 418 #define D_TS_ANCHOR (7<<10) /* Starting short pipes */ 419 #define D_TS_MON(v) ((v)<<5) /* Monitor Pipe */ 420 #define D_TS_NEXT(v) ((v)<<0) /* Pipe no.: 0-15 long, 16-21 short */ 421 422 /* Concentration Highway Interface Modes */ 423 #define D_CHI_CHICM(v) ((v)<<16) /* Clock mode */ 424 #define D_CHI_IR (1<<15) /* Immediate Interrupt Report */ 425 #define D_CHI_EN (1<<14) /* CHIL Interrupt enabled */ 426 #define D_CHI_OD (1<<13) /* Open Drain Enable */ 427 #define D_CHI_FE (1<<12) /* Sample CHIFS on Rising Frame Edge */ 428 #define D_CHI_FD (1<<11) /* Frame Drive */ 429 #define D_CHI_BPF(v) ((v)<<0) /* Bits per Frame */ 430 431 /* NT: These are here for completeness */ 432 #define D_NT_FBIT (1<<17) /* Frame Bit */ 433 #define D_NT_NBF (1<<16) /* Number of bad frames to loose framing */ 434 #define D_NT_IRM_IMM (1<<15) /* Interrupt Report & Mask: Immediate */ 435 #define D_NT_IRM_EN (1<<14) /* Interrupt Report & Mask: Enable */ 436 #define D_NT_ISNT (1<<13) /* Configure interface as NT */ 437 #define D_NT_FT (1<<12) /* Fixed Timing */ 438 #define D_NT_EZ (1<<11) /* Echo Channel is Zeros */ 439 #define D_NT_IFA (1<<10) /* Inhibit Final Activation */ 440 #define D_NT_ACT (1<<9) /* Activate Interface */ 441 #define D_NT_MFE (1<<8) /* Multiframe Enable */ 442 #define D_NT_RLB(v) ((v)<<5) /* Remote Loopback */ 443 #define D_NT_LLB(v) ((v)<<2) /* Local Loopback */ 444 #define D_NT_FACT (1<<1) /* Force Activation */ 445 #define D_NT_ABV (1<<0) /* Activate Bipolar Violation */ 446 447 /* Codec Setup */ 448 #define D_CDEC_CK(v) ((v)<<24) /* Clock Select */ 449 #define D_CDEC_FED(v) ((v)<<12) /* FSCOD Falling Edge Delay */ 450 #define D_CDEC_RED(v) ((v)<<0) /* FSCOD Rising Edge Delay */ 451 452 /* Test */ 453 #define D_TEST_RAM(v) ((v)<<16) /* RAM Pointer */ 454 #define D_TEST_SIZE(v) ((v)<<11) /* */ 455 #define D_TEST_ROMONOFF 0x5 /* Toggle ROM opcode monitor on/off */ 456 #define D_TEST_PROC 0x6 /* Microprocessor test */ 457 #define D_TEST_SER 0x7 /* Serial-Controller test */ 458 #define D_TEST_RAMREAD 0x8 /* Copy from Ram to system memory */ 459 #define D_TEST_RAMWRITE 0x9 /* Copy into Ram from system memory */ 460 #define D_TEST_RAMBIST 0xa /* RAM Built-In Self Test */ 461 #define D_TEST_MCBIST 0xb /* Microcontroller Built-In Self Test */ 462 #define D_TEST_DUMP 0xe /* ROM Dump */ 463 464 /* CHI Data Mode */ 465 #define D_CDM_THI (1 << 8) /* Transmit Data on CHIDR Pin */ 466 #define D_CDM_RHI (1 << 7) /* Receive Data on CHIDX Pin */ 467 #define D_CDM_RCE (1 << 6) /* Receive on Rising Edge of CHICK */ 468 #define D_CDM_XCE (1 << 2) /* Transmit Data on Rising Edge of CHICK */ 469 #define D_CDM_XEN (1 << 1) /* Transmit Highway Enable */ 470 #define D_CDM_REN (1 << 0) /* Receive Highway Enable */ 471 472 /* The Interrupts */ 473 #define D_INTR_BRDY 1 /* Buffer Ready for processing */ 474 #define D_INTR_MINT 2 /* Marked Interrupt in RD/TD */ 475 #define D_INTR_IBEG 3 /* Flag to idle transition detected (HDLC) */ 476 #define D_INTR_IEND 4 /* Idle to flag transition detected (HDLC) */ 477 #define D_INTR_EOL 5 /* End of List */ 478 #define D_INTR_CMDI 6 /* Command has bean read */ 479 #define D_INTR_XCMP 8 /* Transmission of frame complete */ 480 #define D_INTR_SBRI 9 /* BRI status change info */ 481 #define D_INTR_FXDT 10 /* Fixed data change */ 482 #define D_INTR_CHIL 11 /* CHI lost frame sync (channel 36 only) */ 483 #define D_INTR_COLL 11 /* Unrecoverable D-Channel collision */ 484 #define D_INTR_DBYT 12 /* Dropped by frame slip */ 485 #define D_INTR_RBYT 13 /* Repeated by frame slip */ 486 #define D_INTR_LINT 14 /* Lost Interrupt */ 487 #define D_INTR_UNDR 15 /* DMA underrun */ 488 489 #define D_INTR_TE 32 490 #define D_INTR_NT 34 491 #define D_INTR_CHI 36 492 #define D_INTR_CMD 38 493 494 #define D_INTR_GETCHAN(v) (((v) >> 24) & 0x3f) 495 #define D_INTR_GETCODE(v) (((v) >> 20) & 0xf) 496 #define D_INTR_GETCMD(v) (((v) >> 16) & 0xf) 497 #define D_INTR_GETVAL(v) ((v) & 0xffff) 498 #define D_INTR_GETRVAL(v) ((v) & 0xfffff) 499 500 #define D_P_0 0 /* TE receive anchor */ 501 #define D_P_1 1 /* TE transmit anchor */ 502 #define D_P_2 2 /* NT transmit anchor */ 503 #define D_P_3 3 /* NT receive anchor */ 504 #define D_P_4 4 /* CHI send data */ 505 #define D_P_5 5 /* CHI receive data */ 506 #define D_P_6 6 /* */ 507 #define D_P_7 7 /* */ 508 #define D_P_8 8 /* */ 509 #define D_P_9 9 /* */ 510 #define D_P_10 10 /* */ 511 #define D_P_11 11 /* */ 512 #define D_P_12 12 /* */ 513 #define D_P_13 13 /* */ 514 #define D_P_14 14 /* */ 515 #define D_P_15 15 /* */ 516 #define D_P_16 16 /* CHI anchor pipe */ 517 #define D_P_17 17 /* CHI send */ 518 #define D_P_18 18 /* CHI receive */ 519 #define D_P_19 19 /* CHI receive */ 520 #define D_P_20 20 /* CHI receive */ 521 #define D_P_21 21 /* */ 522 #define D_P_22 22 /* */ 523 #define D_P_23 23 /* */ 524 #define D_P_24 24 /* */ 525 #define D_P_25 25 /* */ 526 #define D_P_26 26 /* */ 527 #define D_P_27 27 /* */ 528 #define D_P_28 28 /* */ 529 #define D_P_29 29 /* */ 530 #define D_P_30 30 /* */ 531 #define D_P_31 31 /* */ 532 533 /* Transmit descriptor defines */ 534 #define DBRI_TD_F (1 << 31) /* End of Frame */ 535 #define DBRI_TD_D (1 << 30) /* Do not append CRC */ 536 #define DBRI_TD_CNT(v) ((v) << 16) /* Number of valid bytes in the buffer */ 537 #define DBRI_TD_B (1 << 15) /* Final interrupt */ 538 #define DBRI_TD_M (1 << 14) /* Marker interrupt */ 539 #define DBRI_TD_I (1 << 13) /* Transmit Idle Characters */ 540 #define DBRI_TD_FCNT(v) (v) /* Flag Count */ 541 #define DBRI_TD_UNR (1 << 3) /* Underrun: transmitter is out of data */ 542 #define DBRI_TD_ABT (1 << 2) /* Abort: frame aborted */ 543 #define DBRI_TD_TBC (1 << 0) /* Transmit buffer Complete */ 544 #define DBRI_TD_STATUS(v) ((v) & 0xff) /* Transmit status */ 545 /* Maximum buffer size per TD: almost 8KB */ 546 #define DBRI_TD_MAXCNT ((1 << 13) - 4) 547 548 /* Receive descriptor defines */ 549 #define DBRI_RD_F (1 << 31) /* End of Frame */ 550 #define DBRI_RD_C (1 << 30) /* Completed buffer */ 551 #define DBRI_RD_B (1 << 15) /* Final interrupt */ 552 #define DBRI_RD_M (1 << 14) /* Marker interrupt */ 553 #define DBRI_RD_BCNT(v) (v) /* Buffer size */ 554 #define DBRI_RD_CRC (1 << 7) /* 0: CRC is correct */ 555 #define DBRI_RD_BBC (1 << 6) /* 1: Bad Byte received */ 556 #define DBRI_RD_ABT (1 << 5) /* Abort: frame aborted */ 557 #define DBRI_RD_OVRN (1 << 3) /* Overrun: data lost */ 558 #define DBRI_RD_STATUS(v) ((v) & 0xff) /* Receive status */ 559 #define DBRI_RD_CNT(v) (((v) >> 16) & 0x1fff) /* Valid bytes in the buffer */ 560 561 /* stream_info[] access */ 562 /* Translate the ALSA direction into the array index */ 563 #define DBRI_STREAMNO(substream) \ 564 (substream->stream == \ 565 SNDRV_PCM_STREAM_PLAYBACK ? DBRI_PLAY: DBRI_REC) 566 567 /* Return a pointer to dbri_streaminfo */ 568 #define DBRI_STREAM(dbri, substream) \ 569 &dbri->stream_info[DBRI_STREAMNO(substream)] 570 571 /* 572 * Short data pipes transmit LSB first. The CS4215 receives MSB first. Grrr. 573 * So we have to reverse the bits. Note: not all bit lengths are supported 574 */ 575 static __u32 reverse_bytes(__u32 b, int len) 576 { 577 switch (len) { 578 case 32: 579 b = ((b & 0xffff0000) >> 16) | ((b & 0x0000ffff) << 16); 580 case 16: 581 b = ((b & 0xff00ff00) >> 8) | ((b & 0x00ff00ff) << 8); 582 case 8: 583 b = ((b & 0xf0f0f0f0) >> 4) | ((b & 0x0f0f0f0f) << 4); 584 case 4: 585 b = ((b & 0xcccccccc) >> 2) | ((b & 0x33333333) << 2); 586 case 2: 587 b = ((b & 0xaaaaaaaa) >> 1) | ((b & 0x55555555) << 1); 588 case 1: 589 case 0: 590 break; 591 default: 592 printk(KERN_ERR "DBRI reverse_bytes: unsupported length\n"); 593 }; 594 595 return b; 596 } 597 598 /* 599 **************************************************************************** 600 ************** DBRI initialization and command synchronization ************* 601 **************************************************************************** 602 603 Commands are sent to the DBRI by building a list of them in memory, 604 then writing the address of the first list item to DBRI register 8. 605 The list is terminated with a WAIT command, which generates a 606 CPU interrupt to signal completion. 607 608 Since the DBRI can run in parallel with the CPU, several means of 609 synchronization present themselves. The method implemented here uses 610 the dbri_cmdwait() to wait for execution of batch of sent commands. 611 612 A circular command buffer is used here. A new command is being added 613 while another can be executed. The scheme works by adding two WAIT commands 614 after each sent batch of commands. When the next batch is prepared it is 615 added after the WAIT commands then the WAITs are replaced with single JUMP 616 command to the new batch. The the DBRI is forced to reread the last WAIT 617 command (replaced by the JUMP by then). If the DBRI is still executing 618 previous commands the request to reread the WAIT command is ignored. 619 620 Every time a routine wants to write commands to the DBRI, it must 621 first call dbri_cmdlock() and get pointer to a free space in 622 dbri->dma->cmd buffer. After this, the commands can be written to 623 the buffer, and dbri_cmdsend() is called with the final pointer value 624 to send them to the DBRI. 625 626 */ 627 628 #define MAXLOOPS 20 629 /* 630 * Wait for the current command string to execute 631 */ 632 static void dbri_cmdwait(struct snd_dbri *dbri) 633 { 634 int maxloops = MAXLOOPS; 635 unsigned long flags; 636 637 /* Delay if previous commands are still being processed */ 638 spin_lock_irqsave(&dbri->lock, flags); 639 while ((--maxloops) > 0 && (sbus_readl(dbri->regs + REG0) & D_P)) { 640 spin_unlock_irqrestore(&dbri->lock, flags); 641 msleep_interruptible(1); 642 spin_lock_irqsave(&dbri->lock, flags); 643 } 644 spin_unlock_irqrestore(&dbri->lock, flags); 645 646 if (maxloops == 0) 647 printk(KERN_ERR "DBRI: Chip never completed command buffer\n"); 648 else 649 dprintk(D_CMD, "Chip completed command buffer (%d)\n", 650 MAXLOOPS - maxloops - 1); 651 } 652 /* 653 * Lock the command queue and return pointer to space for len cmd words 654 * It locks the cmdlock spinlock. 655 */ 656 static s32 *dbri_cmdlock(struct snd_dbri *dbri, int len) 657 { 658 /* Space for 2 WAIT cmds (replaced later by 1 JUMP cmd) */ 659 len += 2; 660 spin_lock(&dbri->cmdlock); 661 if (dbri->cmdptr - dbri->dma->cmd + len < DBRI_NO_CMDS - 2) 662 return dbri->cmdptr + 2; 663 else if (len < sbus_readl(dbri->regs + REG8) - dbri->dma_dvma) 664 return dbri->dma->cmd; 665 else 666 printk(KERN_ERR "DBRI: no space for commands."); 667 668 return NULL; 669 } 670 671 /* 672 * Send prepared cmd string. It works by writing a JUMP cmd into 673 * the last WAIT cmd and force DBRI to reread the cmd. 674 * The JUMP cmd points to the new cmd string. 675 * It also releases the cmdlock spinlock. 676 * 677 * Lock must be held before calling this. 678 */ 679 static void dbri_cmdsend(struct snd_dbri *dbri, s32 *cmd, int len) 680 { 681 s32 tmp, addr; 682 static int wait_id = 0; 683 684 wait_id++; 685 wait_id &= 0xffff; /* restrict it to a 16 bit counter. */ 686 *(cmd) = DBRI_CMD(D_WAIT, 1, wait_id); 687 *(cmd+1) = DBRI_CMD(D_WAIT, 1, wait_id); 688 689 /* Replace the last command with JUMP */ 690 addr = dbri->dma_dvma + (cmd - len - dbri->dma->cmd) * sizeof(s32); 691 *(dbri->cmdptr+1) = addr; 692 *(dbri->cmdptr) = DBRI_CMD(D_JUMP, 0, 0); 693 694 #ifdef DBRI_DEBUG 695 if (cmd > dbri->cmdptr) { 696 s32 *ptr; 697 698 for (ptr = dbri->cmdptr; ptr < cmd+2; ptr++) 699 dprintk(D_CMD, "cmd: %lx:%08x\n", 700 (unsigned long)ptr, *ptr); 701 } else { 702 s32 *ptr = dbri->cmdptr; 703 704 dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); 705 ptr++; 706 dprintk(D_CMD, "cmd: %lx:%08x\n", (unsigned long)ptr, *ptr); 707 for (ptr = dbri->dma->cmd; ptr < cmd+2; ptr++) 708 dprintk(D_CMD, "cmd: %lx:%08x\n", 709 (unsigned long)ptr, *ptr); 710 } 711 #endif 712 713 /* Reread the last command */ 714 tmp = sbus_readl(dbri->regs + REG0); 715 tmp |= D_P; 716 sbus_writel(tmp, dbri->regs + REG0); 717 718 dbri->cmdptr = cmd; 719 spin_unlock(&dbri->cmdlock); 720 } 721 722 /* Lock must be held when calling this */ 723 static void dbri_reset(struct snd_dbri *dbri) 724 { 725 int i; 726 u32 tmp; 727 728 dprintk(D_GEN, "reset 0:%x 2:%x 8:%x 9:%x\n", 729 sbus_readl(dbri->regs + REG0), 730 sbus_readl(dbri->regs + REG2), 731 sbus_readl(dbri->regs + REG8), sbus_readl(dbri->regs + REG9)); 732 733 sbus_writel(D_R, dbri->regs + REG0); /* Soft Reset */ 734 for (i = 0; (sbus_readl(dbri->regs + REG0) & D_R) && i < 64; i++) 735 udelay(10); 736 737 /* A brute approach - DBRI falls back to working burst size by itself 738 * On SS20 D_S does not work, so do not try so high. */ 739 tmp = sbus_readl(dbri->regs + REG0); 740 tmp |= D_G | D_E; 741 tmp &= ~D_S; 742 sbus_writel(tmp, dbri->regs + REG0); 743 } 744 745 /* Lock must not be held before calling this */ 746 static void __devinit dbri_initialize(struct snd_dbri *dbri) 747 { 748 s32 *cmd; 749 u32 dma_addr; 750 unsigned long flags; 751 int n; 752 753 spin_lock_irqsave(&dbri->lock, flags); 754 755 dbri_reset(dbri); 756 757 /* Initialize pipes */ 758 for (n = 0; n < DBRI_NO_PIPES; n++) 759 dbri->pipes[n].desc = dbri->pipes[n].first_desc = -1; 760 761 spin_lock_init(&dbri->cmdlock); 762 /* 763 * Initialize the interrupt ring buffer. 764 */ 765 dma_addr = dbri->dma_dvma + dbri_dma_off(intr, 0); 766 dbri->dma->intr[0] = dma_addr; 767 dbri->dbri_irqp = 1; 768 /* 769 * Set up the interrupt queue 770 */ 771 spin_lock(&dbri->cmdlock); 772 cmd = dbri->cmdptr = dbri->dma->cmd; 773 *(cmd++) = DBRI_CMD(D_IIQ, 0, 0); 774 *(cmd++) = dma_addr; 775 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 776 dbri->cmdptr = cmd; 777 *(cmd++) = DBRI_CMD(D_WAIT, 1, 0); 778 *(cmd++) = DBRI_CMD(D_WAIT, 1, 0); 779 dma_addr = dbri->dma_dvma + dbri_dma_off(cmd, 0); 780 sbus_writel(dma_addr, dbri->regs + REG8); 781 spin_unlock(&dbri->cmdlock); 782 783 spin_unlock_irqrestore(&dbri->lock, flags); 784 dbri_cmdwait(dbri); 785 } 786 787 /* 788 **************************************************************************** 789 ************************** DBRI data pipe management *********************** 790 **************************************************************************** 791 792 While DBRI control functions use the command and interrupt buffers, the 793 main data path takes the form of data pipes, which can be short (command 794 and interrupt driven), or long (attached to DMA buffers). These functions 795 provide a rudimentary means of setting up and managing the DBRI's pipes, 796 but the calling functions have to make sure they respect the pipes' linked 797 list ordering, among other things. The transmit and receive functions 798 here interface closely with the transmit and receive interrupt code. 799 800 */ 801 static inline int pipe_active(struct snd_dbri *dbri, int pipe) 802 { 803 return ((pipe >= 0) && (dbri->pipes[pipe].desc != -1)); 804 } 805 806 /* reset_pipe(dbri, pipe) 807 * 808 * Called on an in-use pipe to clear anything being transmitted or received 809 * Lock must be held before calling this. 810 */ 811 static void reset_pipe(struct snd_dbri *dbri, int pipe) 812 { 813 int sdp; 814 int desc; 815 s32 *cmd; 816 817 if (pipe < 0 || pipe > DBRI_MAX_PIPE) { 818 printk(KERN_ERR "DBRI: reset_pipe called with " 819 "illegal pipe number\n"); 820 return; 821 } 822 823 sdp = dbri->pipes[pipe].sdp; 824 if (sdp == 0) { 825 printk(KERN_ERR "DBRI: reset_pipe called " 826 "on uninitialized pipe\n"); 827 return; 828 } 829 830 cmd = dbri_cmdlock(dbri, 3); 831 *(cmd++) = DBRI_CMD(D_SDP, 0, sdp | D_SDP_C | D_SDP_P); 832 *(cmd++) = 0; 833 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 834 dbri_cmdsend(dbri, cmd, 3); 835 836 desc = dbri->pipes[pipe].first_desc; 837 if (desc >= 0) 838 do { 839 dbri->dma->desc[desc].ba = 0; 840 dbri->dma->desc[desc].nda = 0; 841 desc = dbri->next_desc[desc]; 842 } while (desc != -1 && desc != dbri->pipes[pipe].first_desc); 843 844 dbri->pipes[pipe].desc = -1; 845 dbri->pipes[pipe].first_desc = -1; 846 } 847 848 /* 849 * Lock must be held before calling this. 850 */ 851 static void setup_pipe(struct snd_dbri *dbri, int pipe, int sdp) 852 { 853 if (pipe < 0 || pipe > DBRI_MAX_PIPE) { 854 printk(KERN_ERR "DBRI: setup_pipe called " 855 "with illegal pipe number\n"); 856 return; 857 } 858 859 if ((sdp & 0xf800) != sdp) { 860 printk(KERN_ERR "DBRI: setup_pipe called " 861 "with strange SDP value\n"); 862 /* sdp &= 0xf800; */ 863 } 864 865 /* If this is a fixed receive pipe, arrange for an interrupt 866 * every time its data changes 867 */ 868 if (D_SDP_MODE(sdp) == D_SDP_FIXED && !(sdp & D_SDP_TO_SER)) 869 sdp |= D_SDP_CHANGE; 870 871 sdp |= D_PIPE(pipe); 872 dbri->pipes[pipe].sdp = sdp; 873 dbri->pipes[pipe].desc = -1; 874 dbri->pipes[pipe].first_desc = -1; 875 876 reset_pipe(dbri, pipe); 877 } 878 879 /* 880 * Lock must be held before calling this. 881 */ 882 static void link_time_slot(struct snd_dbri *dbri, int pipe, 883 int prevpipe, int nextpipe, 884 int length, int cycle) 885 { 886 s32 *cmd; 887 int val; 888 889 if (pipe < 0 || pipe > DBRI_MAX_PIPE 890 || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE 891 || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) { 892 printk(KERN_ERR 893 "DBRI: link_time_slot called with illegal pipe number\n"); 894 return; 895 } 896 897 if (dbri->pipes[pipe].sdp == 0 898 || dbri->pipes[prevpipe].sdp == 0 899 || dbri->pipes[nextpipe].sdp == 0) { 900 printk(KERN_ERR "DBRI: link_time_slot called " 901 "on uninitialized pipe\n"); 902 return; 903 } 904 905 dbri->pipes[prevpipe].nextpipe = pipe; 906 dbri->pipes[pipe].nextpipe = nextpipe; 907 dbri->pipes[pipe].length = length; 908 909 cmd = dbri_cmdlock(dbri, 4); 910 911 if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) { 912 /* Deal with CHI special case: 913 * "If transmission on edges 0 or 1 is desired, then cycle n 914 * (where n = # of bit times per frame...) must be used." 915 * - DBRI data sheet, page 11 916 */ 917 if (prevpipe == 16 && cycle == 0) 918 cycle = dbri->chi_bpf; 919 920 val = D_DTS_VO | D_DTS_INS | D_DTS_PRVOUT(prevpipe) | pipe; 921 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 922 *(cmd++) = 0; 923 *(cmd++) = 924 D_TS_LEN(length) | D_TS_CYCLE(cycle) | D_TS_NEXT(nextpipe); 925 } else { 926 val = D_DTS_VI | D_DTS_INS | D_DTS_PRVIN(prevpipe) | pipe; 927 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 928 *(cmd++) = 929 D_TS_LEN(length) | D_TS_CYCLE(cycle) | D_TS_NEXT(nextpipe); 930 *(cmd++) = 0; 931 } 932 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 933 934 dbri_cmdsend(dbri, cmd, 4); 935 } 936 937 #if 0 938 /* 939 * Lock must be held before calling this. 940 */ 941 static void unlink_time_slot(struct snd_dbri *dbri, int pipe, 942 enum in_or_out direction, int prevpipe, 943 int nextpipe) 944 { 945 s32 *cmd; 946 int val; 947 948 if (pipe < 0 || pipe > DBRI_MAX_PIPE 949 || prevpipe < 0 || prevpipe > DBRI_MAX_PIPE 950 || nextpipe < 0 || nextpipe > DBRI_MAX_PIPE) { 951 printk(KERN_ERR 952 "DBRI: unlink_time_slot called with illegal pipe number\n"); 953 return; 954 } 955 956 cmd = dbri_cmdlock(dbri, 4); 957 958 if (direction == PIPEinput) { 959 val = D_DTS_VI | D_DTS_DEL | D_DTS_PRVIN(prevpipe) | pipe; 960 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 961 *(cmd++) = D_TS_NEXT(nextpipe); 962 *(cmd++) = 0; 963 } else { 964 val = D_DTS_VO | D_DTS_DEL | D_DTS_PRVOUT(prevpipe) | pipe; 965 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 966 *(cmd++) = 0; 967 *(cmd++) = D_TS_NEXT(nextpipe); 968 } 969 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 970 971 dbri_cmdsend(dbri, cmd, 4); 972 } 973 #endif 974 975 /* xmit_fixed() / recv_fixed() 976 * 977 * Transmit/receive data on a "fixed" pipe - i.e, one whose contents are not 978 * expected to change much, and which we don't need to buffer. 979 * The DBRI only interrupts us when the data changes (receive pipes), 980 * or only changes the data when this function is called (transmit pipes). 981 * Only short pipes (numbers 16-31) can be used in fixed data mode. 982 * 983 * These function operate on a 32-bit field, no matter how large 984 * the actual time slot is. The interrupt handler takes care of bit 985 * ordering and alignment. An 8-bit time slot will always end up 986 * in the low-order 8 bits, filled either MSB-first or LSB-first, 987 * depending on the settings passed to setup_pipe(). 988 * 989 * Lock must not be held before calling it. 990 */ 991 static void xmit_fixed(struct snd_dbri *dbri, int pipe, unsigned int data) 992 { 993 s32 *cmd; 994 unsigned long flags; 995 996 if (pipe < 16 || pipe > DBRI_MAX_PIPE) { 997 printk(KERN_ERR "DBRI: xmit_fixed: Illegal pipe number\n"); 998 return; 999 } 1000 1001 if (D_SDP_MODE(dbri->pipes[pipe].sdp) == 0) { 1002 printk(KERN_ERR "DBRI: xmit_fixed: " 1003 "Uninitialized pipe %d\n", pipe); 1004 return; 1005 } 1006 1007 if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) { 1008 printk(KERN_ERR "DBRI: xmit_fixed: Non-fixed pipe %d\n", pipe); 1009 return; 1010 } 1011 1012 if (!(dbri->pipes[pipe].sdp & D_SDP_TO_SER)) { 1013 printk(KERN_ERR "DBRI: xmit_fixed: Called on receive pipe %d\n", 1014 pipe); 1015 return; 1016 } 1017 1018 /* DBRI short pipes always transmit LSB first */ 1019 1020 if (dbri->pipes[pipe].sdp & D_SDP_MSB) 1021 data = reverse_bytes(data, dbri->pipes[pipe].length); 1022 1023 cmd = dbri_cmdlock(dbri, 3); 1024 1025 *(cmd++) = DBRI_CMD(D_SSP, 0, pipe); 1026 *(cmd++) = data; 1027 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1028 1029 spin_lock_irqsave(&dbri->lock, flags); 1030 dbri_cmdsend(dbri, cmd, 3); 1031 spin_unlock_irqrestore(&dbri->lock, flags); 1032 dbri_cmdwait(dbri); 1033 1034 } 1035 1036 static void recv_fixed(struct snd_dbri *dbri, int pipe, volatile __u32 *ptr) 1037 { 1038 if (pipe < 16 || pipe > DBRI_MAX_PIPE) { 1039 printk(KERN_ERR "DBRI: recv_fixed called with " 1040 "illegal pipe number\n"); 1041 return; 1042 } 1043 1044 if (D_SDP_MODE(dbri->pipes[pipe].sdp) != D_SDP_FIXED) { 1045 printk(KERN_ERR "DBRI: recv_fixed called on " 1046 "non-fixed pipe %d\n", pipe); 1047 return; 1048 } 1049 1050 if (dbri->pipes[pipe].sdp & D_SDP_TO_SER) { 1051 printk(KERN_ERR "DBRI: recv_fixed called on " 1052 "transmit pipe %d\n", pipe); 1053 return; 1054 } 1055 1056 dbri->pipes[pipe].recv_fixed_ptr = ptr; 1057 } 1058 1059 /* setup_descs() 1060 * 1061 * Setup transmit/receive data on a "long" pipe - i.e, one associated 1062 * with a DMA buffer. 1063 * 1064 * Only pipe numbers 0-15 can be used in this mode. 1065 * 1066 * This function takes a stream number pointing to a data buffer, 1067 * and work by building chains of descriptors which identify the 1068 * data buffers. Buffers too large for a single descriptor will 1069 * be spread across multiple descriptors. 1070 * 1071 * All descriptors create a ring buffer. 1072 * 1073 * Lock must be held before calling this. 1074 */ 1075 static int setup_descs(struct snd_dbri *dbri, int streamno, unsigned int period) 1076 { 1077 struct dbri_streaminfo *info = &dbri->stream_info[streamno]; 1078 __u32 dvma_buffer; 1079 int desc; 1080 int len; 1081 int first_desc = -1; 1082 int last_desc = -1; 1083 1084 if (info->pipe < 0 || info->pipe > 15) { 1085 printk(KERN_ERR "DBRI: setup_descs: Illegal pipe number\n"); 1086 return -2; 1087 } 1088 1089 if (dbri->pipes[info->pipe].sdp == 0) { 1090 printk(KERN_ERR "DBRI: setup_descs: Uninitialized pipe %d\n", 1091 info->pipe); 1092 return -2; 1093 } 1094 1095 dvma_buffer = info->dvma_buffer; 1096 len = info->size; 1097 1098 if (streamno == DBRI_PLAY) { 1099 if (!(dbri->pipes[info->pipe].sdp & D_SDP_TO_SER)) { 1100 printk(KERN_ERR "DBRI: setup_descs: " 1101 "Called on receive pipe %d\n", info->pipe); 1102 return -2; 1103 } 1104 } else { 1105 if (dbri->pipes[info->pipe].sdp & D_SDP_TO_SER) { 1106 printk(KERN_ERR 1107 "DBRI: setup_descs: Called on transmit pipe %d\n", 1108 info->pipe); 1109 return -2; 1110 } 1111 /* Should be able to queue multiple buffers 1112 * to receive on a pipe 1113 */ 1114 if (pipe_active(dbri, info->pipe)) { 1115 printk(KERN_ERR "DBRI: recv_on_pipe: " 1116 "Called on active pipe %d\n", info->pipe); 1117 return -2; 1118 } 1119 1120 /* Make sure buffer size is multiple of four */ 1121 len &= ~3; 1122 } 1123 1124 /* Free descriptors if pipe has any */ 1125 desc = dbri->pipes[info->pipe].first_desc; 1126 if (desc >= 0) 1127 do { 1128 dbri->dma->desc[desc].ba = 0; 1129 dbri->dma->desc[desc].nda = 0; 1130 desc = dbri->next_desc[desc]; 1131 } while (desc != -1 && 1132 desc != dbri->pipes[info->pipe].first_desc); 1133 1134 dbri->pipes[info->pipe].desc = -1; 1135 dbri->pipes[info->pipe].first_desc = -1; 1136 1137 desc = 0; 1138 while (len > 0) { 1139 int mylen; 1140 1141 for (; desc < DBRI_NO_DESCS; desc++) { 1142 if (!dbri->dma->desc[desc].ba) 1143 break; 1144 } 1145 1146 if (desc == DBRI_NO_DESCS) { 1147 printk(KERN_ERR "DBRI: setup_descs: No descriptors\n"); 1148 return -1; 1149 } 1150 1151 if (len > DBRI_TD_MAXCNT) 1152 mylen = DBRI_TD_MAXCNT; /* 8KB - 4 */ 1153 else 1154 mylen = len; 1155 1156 if (mylen > period) 1157 mylen = period; 1158 1159 dbri->next_desc[desc] = -1; 1160 dbri->dma->desc[desc].ba = dvma_buffer; 1161 dbri->dma->desc[desc].nda = 0; 1162 1163 if (streamno == DBRI_PLAY) { 1164 dbri->dma->desc[desc].word1 = DBRI_TD_CNT(mylen); 1165 dbri->dma->desc[desc].word4 = 0; 1166 dbri->dma->desc[desc].word1 |= DBRI_TD_F | DBRI_TD_B; 1167 } else { 1168 dbri->dma->desc[desc].word1 = 0; 1169 dbri->dma->desc[desc].word4 = 1170 DBRI_RD_B | DBRI_RD_BCNT(mylen); 1171 } 1172 1173 if (first_desc == -1) 1174 first_desc = desc; 1175 else { 1176 dbri->next_desc[last_desc] = desc; 1177 dbri->dma->desc[last_desc].nda = 1178 dbri->dma_dvma + dbri_dma_off(desc, desc); 1179 } 1180 1181 last_desc = desc; 1182 dvma_buffer += mylen; 1183 len -= mylen; 1184 } 1185 1186 if (first_desc == -1 || last_desc == -1) { 1187 printk(KERN_ERR "DBRI: setup_descs: " 1188 " Not enough descriptors available\n"); 1189 return -1; 1190 } 1191 1192 dbri->dma->desc[last_desc].nda = 1193 dbri->dma_dvma + dbri_dma_off(desc, first_desc); 1194 dbri->next_desc[last_desc] = first_desc; 1195 dbri->pipes[info->pipe].first_desc = first_desc; 1196 dbri->pipes[info->pipe].desc = first_desc; 1197 1198 #ifdef DBRI_DEBUG 1199 for (desc = first_desc; desc != -1;) { 1200 dprintk(D_DESC, "DESC %d: %08x %08x %08x %08x\n", 1201 desc, 1202 dbri->dma->desc[desc].word1, 1203 dbri->dma->desc[desc].ba, 1204 dbri->dma->desc[desc].nda, dbri->dma->desc[desc].word4); 1205 desc = dbri->next_desc[desc]; 1206 if (desc == first_desc) 1207 break; 1208 } 1209 #endif 1210 return 0; 1211 } 1212 1213 /* 1214 **************************************************************************** 1215 ************************** DBRI - CHI interface **************************** 1216 **************************************************************************** 1217 1218 The CHI is a four-wire (clock, frame sync, data in, data out) time-division 1219 multiplexed serial interface which the DBRI can operate in either master 1220 (give clock/frame sync) or slave (take clock/frame sync) mode. 1221 1222 */ 1223 1224 enum master_or_slave { CHImaster, CHIslave }; 1225 1226 /* 1227 * Lock must not be held before calling it. 1228 */ 1229 static void reset_chi(struct snd_dbri *dbri, 1230 enum master_or_slave master_or_slave, 1231 int bits_per_frame) 1232 { 1233 s32 *cmd; 1234 int val; 1235 1236 /* Set CHI Anchor: Pipe 16 */ 1237 1238 cmd = dbri_cmdlock(dbri, 4); 1239 val = D_DTS_VO | D_DTS_VI | D_DTS_INS 1240 | D_DTS_PRVIN(16) | D_PIPE(16) | D_DTS_PRVOUT(16); 1241 *(cmd++) = DBRI_CMD(D_DTS, 0, val); 1242 *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16); 1243 *(cmd++) = D_TS_ANCHOR | D_TS_NEXT(16); 1244 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1245 dbri_cmdsend(dbri, cmd, 4); 1246 1247 dbri->pipes[16].sdp = 1; 1248 dbri->pipes[16].nextpipe = 16; 1249 1250 cmd = dbri_cmdlock(dbri, 4); 1251 1252 if (master_or_slave == CHIslave) { 1253 /* Setup DBRI for CHI Slave - receive clock, frame sync (FS) 1254 * 1255 * CHICM = 0 (slave mode, 8 kHz frame rate) 1256 * IR = give immediate CHI status interrupt 1257 * EN = give CHI status interrupt upon change 1258 */ 1259 *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(0)); 1260 } else { 1261 /* Setup DBRI for CHI Master - generate clock, FS 1262 * 1263 * BPF = bits per 8 kHz frame 1264 * 12.288 MHz / CHICM_divisor = clock rate 1265 * FD = 1 - drive CHIFS on rising edge of CHICK 1266 */ 1267 int clockrate = bits_per_frame * 8; 1268 int divisor = 12288 / clockrate; 1269 1270 if (divisor > 255 || divisor * clockrate != 12288) 1271 printk(KERN_ERR "DBRI: illegal bits_per_frame " 1272 "in setup_chi\n"); 1273 1274 *(cmd++) = DBRI_CMD(D_CHI, 0, D_CHI_CHICM(divisor) | D_CHI_FD 1275 | D_CHI_BPF(bits_per_frame)); 1276 } 1277 1278 dbri->chi_bpf = bits_per_frame; 1279 1280 /* CHI Data Mode 1281 * 1282 * RCE = 0 - receive on falling edge of CHICK 1283 * XCE = 1 - transmit on rising edge of CHICK 1284 * XEN = 1 - enable transmitter 1285 * REN = 1 - enable receiver 1286 */ 1287 1288 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1289 *(cmd++) = DBRI_CMD(D_CDM, 0, D_CDM_XCE | D_CDM_XEN | D_CDM_REN); 1290 *(cmd++) = DBRI_CMD(D_PAUSE, 0, 0); 1291 1292 dbri_cmdsend(dbri, cmd, 4); 1293 } 1294 1295 /* 1296 **************************************************************************** 1297 *********************** CS4215 audio codec management ********************** 1298 **************************************************************************** 1299 1300 In the standard SPARC audio configuration, the CS4215 codec is attached 1301 to the DBRI via the CHI interface and few of the DBRI's PIO pins. 1302 1303 * Lock must not be held before calling it. 1304 1305 */ 1306 static __devinit void cs4215_setup_pipes(struct snd_dbri *dbri) 1307 { 1308 unsigned long flags; 1309 1310 spin_lock_irqsave(&dbri->lock, flags); 1311 /* 1312 * Data mode: 1313 * Pipe 4: Send timeslots 1-4 (audio data) 1314 * Pipe 20: Send timeslots 5-8 (part of ctrl data) 1315 * Pipe 6: Receive timeslots 1-4 (audio data) 1316 * Pipe 21: Receive timeslots 6-7. We can only receive 20 bits via 1317 * interrupt, and the rest of the data (slot 5 and 8) is 1318 * not relevant for us (only for doublechecking). 1319 * 1320 * Control mode: 1321 * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only) 1322 * Pipe 18: Receive timeslot 1 (clb). 1323 * Pipe 19: Receive timeslot 7 (version). 1324 */ 1325 1326 setup_pipe(dbri, 4, D_SDP_MEM | D_SDP_TO_SER | D_SDP_MSB); 1327 setup_pipe(dbri, 20, D_SDP_FIXED | D_SDP_TO_SER | D_SDP_MSB); 1328 setup_pipe(dbri, 6, D_SDP_MEM | D_SDP_FROM_SER | D_SDP_MSB); 1329 setup_pipe(dbri, 21, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB); 1330 1331 setup_pipe(dbri, 17, D_SDP_FIXED | D_SDP_TO_SER | D_SDP_MSB); 1332 setup_pipe(dbri, 18, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB); 1333 setup_pipe(dbri, 19, D_SDP_FIXED | D_SDP_FROM_SER | D_SDP_MSB); 1334 spin_unlock_irqrestore(&dbri->lock, flags); 1335 1336 dbri_cmdwait(dbri); 1337 } 1338 1339 static __devinit int cs4215_init_data(struct cs4215 *mm) 1340 { 1341 /* 1342 * No action, memory resetting only. 1343 * 1344 * Data Time Slot 5-8 1345 * Speaker,Line and Headphone enable. Gain set to the half. 1346 * Input is mike. 1347 */ 1348 mm->data[0] = CS4215_LO(0x20) | CS4215_HE | CS4215_LE; 1349 mm->data[1] = CS4215_RO(0x20) | CS4215_SE; 1350 mm->data[2] = CS4215_LG(0x8) | CS4215_IS | CS4215_PIO0 | CS4215_PIO1; 1351 mm->data[3] = CS4215_RG(0x8) | CS4215_MA(0xf); 1352 1353 /* 1354 * Control Time Slot 1-4 1355 * 0: Default I/O voltage scale 1356 * 1: 8 bit ulaw, 8kHz, mono, high pass filter disabled 1357 * 2: Serial enable, CHI master, 128 bits per frame, clock 1 1358 * 3: Tests disabled 1359 */ 1360 mm->ctrl[0] = CS4215_RSRVD_1 | CS4215_MLB; 1361 mm->ctrl[1] = CS4215_DFR_ULAW | CS4215_FREQ[0].csval; 1362 mm->ctrl[2] = CS4215_XCLK | CS4215_BSEL_128 | CS4215_FREQ[0].xtal; 1363 mm->ctrl[3] = 0; 1364 1365 mm->status = 0; 1366 mm->version = 0xff; 1367 mm->precision = 8; /* For ULAW */ 1368 mm->channels = 1; 1369 1370 return 0; 1371 } 1372 1373 static void cs4215_setdata(struct snd_dbri *dbri, int muted) 1374 { 1375 if (muted) { 1376 dbri->mm.data[0] |= 63; 1377 dbri->mm.data[1] |= 63; 1378 dbri->mm.data[2] &= ~15; 1379 dbri->mm.data[3] &= ~15; 1380 } else { 1381 /* Start by setting the playback attenuation. */ 1382 struct dbri_streaminfo *info = &dbri->stream_info[DBRI_PLAY]; 1383 int left_gain = info->left_gain & 0x3f; 1384 int right_gain = info->right_gain & 0x3f; 1385 1386 dbri->mm.data[0] &= ~0x3f; /* Reset the volume bits */ 1387 dbri->mm.data[1] &= ~0x3f; 1388 dbri->mm.data[0] |= (DBRI_MAX_VOLUME - left_gain); 1389 dbri->mm.data[1] |= (DBRI_MAX_VOLUME - right_gain); 1390 1391 /* Now set the recording gain. */ 1392 info = &dbri->stream_info[DBRI_REC]; 1393 left_gain = info->left_gain & 0xf; 1394 right_gain = info->right_gain & 0xf; 1395 dbri->mm.data[2] |= CS4215_LG(left_gain); 1396 dbri->mm.data[3] |= CS4215_RG(right_gain); 1397 } 1398 1399 xmit_fixed(dbri, 20, *(int *)dbri->mm.data); 1400 } 1401 1402 /* 1403 * Set the CS4215 to data mode. 1404 */ 1405 static void cs4215_open(struct snd_dbri *dbri) 1406 { 1407 int data_width; 1408 u32 tmp; 1409 unsigned long flags; 1410 1411 dprintk(D_MM, "cs4215_open: %d channels, %d bits\n", 1412 dbri->mm.channels, dbri->mm.precision); 1413 1414 /* Temporarily mute outputs, and wait 1/8000 sec (125 us) 1415 * to make sure this takes. This avoids clicking noises. 1416 */ 1417 1418 cs4215_setdata(dbri, 1); 1419 udelay(125); 1420 1421 /* 1422 * Data mode: 1423 * Pipe 4: Send timeslots 1-4 (audio data) 1424 * Pipe 20: Send timeslots 5-8 (part of ctrl data) 1425 * Pipe 6: Receive timeslots 1-4 (audio data) 1426 * Pipe 21: Receive timeslots 6-7. We can only receive 20 bits via 1427 * interrupt, and the rest of the data (slot 5 and 8) is 1428 * not relevant for us (only for doublechecking). 1429 * 1430 * Just like in control mode, the time slots are all offset by eight 1431 * bits. The CS4215, it seems, observes TSIN (the delayed signal) 1432 * even if it's the CHI master. Don't ask me... 1433 */ 1434 spin_lock_irqsave(&dbri->lock, flags); 1435 tmp = sbus_readl(dbri->regs + REG0); 1436 tmp &= ~(D_C); /* Disable CHI */ 1437 sbus_writel(tmp, dbri->regs + REG0); 1438 1439 /* Switch CS4215 to data mode - set PIO3 to 1 */ 1440 sbus_writel(D_ENPIO | D_PIO1 | D_PIO3 | 1441 (dbri->mm.onboard ? D_PIO0 : D_PIO2), dbri->regs + REG2); 1442 1443 reset_chi(dbri, CHIslave, 128); 1444 1445 /* Note: this next doesn't work for 8-bit stereo, because the two 1446 * channels would be on timeslots 1 and 3, with 2 and 4 idle. 1447 * (See CS4215 datasheet Fig 15) 1448 * 1449 * DBRI non-contiguous mode would be required to make this work. 1450 */ 1451 data_width = dbri->mm.channels * dbri->mm.precision; 1452 1453 link_time_slot(dbri, 4, 16, 16, data_width, dbri->mm.offset); 1454 link_time_slot(dbri, 20, 4, 16, 32, dbri->mm.offset + 32); 1455 link_time_slot(dbri, 6, 16, 16, data_width, dbri->mm.offset); 1456 link_time_slot(dbri, 21, 6, 16, 16, dbri->mm.offset + 40); 1457 1458 /* FIXME: enable CHI after _setdata? */ 1459 tmp = sbus_readl(dbri->regs + REG0); 1460 tmp |= D_C; /* Enable CHI */ 1461 sbus_writel(tmp, dbri->regs + REG0); 1462 spin_unlock_irqrestore(&dbri->lock, flags); 1463 1464 cs4215_setdata(dbri, 0); 1465 } 1466 1467 /* 1468 * Send the control information (i.e. audio format) 1469 */ 1470 static int cs4215_setctrl(struct snd_dbri *dbri) 1471 { 1472 int i, val; 1473 u32 tmp; 1474 unsigned long flags; 1475 1476 /* FIXME - let the CPU do something useful during these delays */ 1477 1478 /* Temporarily mute outputs, and wait 1/8000 sec (125 us) 1479 * to make sure this takes. This avoids clicking noises. 1480 */ 1481 cs4215_setdata(dbri, 1); 1482 udelay(125); 1483 1484 /* 1485 * Enable Control mode: Set DBRI's PIO3 (4215's D/~C) to 0, then wait 1486 * 12 cycles <= 12/(5512.5*64) sec = 34.01 usec 1487 */ 1488 val = D_ENPIO | D_PIO1 | (dbri->mm.onboard ? D_PIO0 : D_PIO2); 1489 sbus_writel(val, dbri->regs + REG2); 1490 dprintk(D_MM, "cs4215_setctrl: reg2=0x%x\n", val); 1491 udelay(34); 1492 1493 /* In Control mode, the CS4215 is a slave device, so the DBRI must 1494 * operate as CHI master, supplying clocking and frame synchronization. 1495 * 1496 * In Data mode, however, the CS4215 must be CHI master to insure 1497 * that its data stream is synchronous with its codec. 1498 * 1499 * The upshot of all this? We start by putting the DBRI into master 1500 * mode, program the CS4215 in Control mode, then switch the CS4215 1501 * into Data mode and put the DBRI into slave mode. Various timing 1502 * requirements must be observed along the way. 1503 * 1504 * Oh, and one more thing, on a SPARCStation 20 (and maybe 1505 * others?), the addressing of the CS4215's time slots is 1506 * offset by eight bits, so we add eight to all the "cycle" 1507 * values in the Define Time Slot (DTS) commands. This is 1508 * done in hardware by a TI 248 that delays the DBRI->4215 1509 * frame sync signal by eight clock cycles. Anybody know why? 1510 */ 1511 spin_lock_irqsave(&dbri->lock, flags); 1512 tmp = sbus_readl(dbri->regs + REG0); 1513 tmp &= ~D_C; /* Disable CHI */ 1514 sbus_writel(tmp, dbri->regs + REG0); 1515 1516 reset_chi(dbri, CHImaster, 128); 1517 1518 /* 1519 * Control mode: 1520 * Pipe 17: Send timeslots 1-4 (slots 5-8 are read only) 1521 * Pipe 18: Receive timeslot 1 (clb). 1522 * Pipe 19: Receive timeslot 7 (version). 1523 */ 1524 1525 link_time_slot(dbri, 17, 16, 16, 32, dbri->mm.offset); 1526 link_time_slot(dbri, 18, 16, 16, 8, dbri->mm.offset); 1527 link_time_slot(dbri, 19, 18, 16, 8, dbri->mm.offset + 48); 1528 spin_unlock_irqrestore(&dbri->lock, flags); 1529 1530 /* Wait for the chip to echo back CLB (Control Latch Bit) as zero */ 1531 dbri->mm.ctrl[0] &= ~CS4215_CLB; 1532 xmit_fixed(dbri, 17, *(int *)dbri->mm.ctrl); 1533 1534 spin_lock_irqsave(&dbri->lock, flags); 1535 tmp = sbus_readl(dbri->regs + REG0); 1536 tmp |= D_C; /* Enable CHI */ 1537 sbus_writel(tmp, dbri->regs + REG0); 1538 spin_unlock_irqrestore(&dbri->lock, flags); 1539 1540 for (i = 10; ((dbri->mm.status & 0xe4) != 0x20); --i) 1541 msleep_interruptible(1); 1542 1543 if (i == 0) { 1544 dprintk(D_MM, "CS4215 didn't respond to CLB (0x%02x)\n", 1545 dbri->mm.status); 1546 return -1; 1547 } 1548 1549 /* Disable changes to our copy of the version number, as we are about 1550 * to leave control mode. 1551 */ 1552 recv_fixed(dbri, 19, NULL); 1553 1554 /* Terminate CS4215 control mode - data sheet says 1555 * "Set CLB=1 and send two more frames of valid control info" 1556 */ 1557 dbri->mm.ctrl[0] |= CS4215_CLB; 1558 xmit_fixed(dbri, 17, *(int *)dbri->mm.ctrl); 1559 1560 /* Two frames of control info @ 8kHz frame rate = 250 us delay */ 1561 udelay(250); 1562 1563 cs4215_setdata(dbri, 0); 1564 1565 return 0; 1566 } 1567 1568 /* 1569 * Setup the codec with the sampling rate, audio format and number of 1570 * channels. 1571 * As part of the process we resend the settings for the data 1572 * timeslots as well. 1573 */ 1574 static int cs4215_prepare(struct snd_dbri *dbri, unsigned int rate, 1575 snd_pcm_format_t format, unsigned int channels) 1576 { 1577 int freq_idx; 1578 int ret = 0; 1579 1580 /* Lookup index for this rate */ 1581 for (freq_idx = 0; CS4215_FREQ[freq_idx].freq != 0; freq_idx++) { 1582 if (CS4215_FREQ[freq_idx].freq == rate) 1583 break; 1584 } 1585 if (CS4215_FREQ[freq_idx].freq != rate) { 1586 printk(KERN_WARNING "DBRI: Unsupported rate %d Hz\n", rate); 1587 return -1; 1588 } 1589 1590 switch (format) { 1591 case SNDRV_PCM_FORMAT_MU_LAW: 1592 dbri->mm.ctrl[1] = CS4215_DFR_ULAW; 1593 dbri->mm.precision = 8; 1594 break; 1595 case SNDRV_PCM_FORMAT_A_LAW: 1596 dbri->mm.ctrl[1] = CS4215_DFR_ALAW; 1597 dbri->mm.precision = 8; 1598 break; 1599 case SNDRV_PCM_FORMAT_U8: 1600 dbri->mm.ctrl[1] = CS4215_DFR_LINEAR8; 1601 dbri->mm.precision = 8; 1602 break; 1603 case SNDRV_PCM_FORMAT_S16_BE: 1604 dbri->mm.ctrl[1] = CS4215_DFR_LINEAR16; 1605 dbri->mm.precision = 16; 1606 break; 1607 default: 1608 printk(KERN_WARNING "DBRI: Unsupported format %d\n", format); 1609 return -1; 1610 } 1611 1612 /* Add rate parameters */ 1613 dbri->mm.ctrl[1] |= CS4215_FREQ[freq_idx].csval; 1614 dbri->mm.ctrl[2] = CS4215_XCLK | 1615 CS4215_BSEL_128 | CS4215_FREQ[freq_idx].xtal; 1616 1617 dbri->mm.channels = channels; 1618 if (channels == 2) 1619 dbri->mm.ctrl[1] |= CS4215_DFR_STEREO; 1620 1621 ret = cs4215_setctrl(dbri); 1622 if (ret == 0) 1623 cs4215_open(dbri); /* set codec to data mode */ 1624 1625 return ret; 1626 } 1627 1628 /* 1629 * 1630 */ 1631 static __devinit int cs4215_init(struct snd_dbri *dbri) 1632 { 1633 u32 reg2 = sbus_readl(dbri->regs + REG2); 1634 dprintk(D_MM, "cs4215_init: reg2=0x%x\n", reg2); 1635 1636 /* Look for the cs4215 chips */ 1637 if (reg2 & D_PIO2) { 1638 dprintk(D_MM, "Onboard CS4215 detected\n"); 1639 dbri->mm.onboard = 1; 1640 } 1641 if (reg2 & D_PIO0) { 1642 dprintk(D_MM, "Speakerbox detected\n"); 1643 dbri->mm.onboard = 0; 1644 1645 if (reg2 & D_PIO2) { 1646 printk(KERN_INFO "DBRI: Using speakerbox / " 1647 "ignoring onboard mmcodec.\n"); 1648 sbus_writel(D_ENPIO2, dbri->regs + REG2); 1649 } 1650 } 1651 1652 if (!(reg2 & (D_PIO0 | D_PIO2))) { 1653 printk(KERN_ERR "DBRI: no mmcodec found.\n"); 1654 return -EIO; 1655 } 1656 1657 cs4215_setup_pipes(dbri); 1658 cs4215_init_data(&dbri->mm); 1659 1660 /* Enable capture of the status & version timeslots. */ 1661 recv_fixed(dbri, 18, &dbri->mm.status); 1662 recv_fixed(dbri, 19, &dbri->mm.version); 1663 1664 dbri->mm.offset = dbri->mm.onboard ? 0 : 8; 1665 if (cs4215_setctrl(dbri) == -1 || dbri->mm.version == 0xff) { 1666 dprintk(D_MM, "CS4215 failed probe at offset %d\n", 1667 dbri->mm.offset); 1668 return -EIO; 1669 } 1670 dprintk(D_MM, "Found CS4215 at offset %d\n", dbri->mm.offset); 1671 1672 return 0; 1673 } 1674 1675 /* 1676 **************************************************************************** 1677 *************************** DBRI interrupt handler ************************* 1678 **************************************************************************** 1679 1680 The DBRI communicates with the CPU mainly via a circular interrupt 1681 buffer. When an interrupt is signaled, the CPU walks through the 1682 buffer and calls dbri_process_one_interrupt() for each interrupt word. 1683 Complicated interrupts are handled by dedicated functions (which 1684 appear first in this file). Any pending interrupts can be serviced by 1685 calling dbri_process_interrupt_buffer(), which works even if the CPU's 1686 interrupts are disabled. 1687 1688 */ 1689 1690 /* xmit_descs() 1691 * 1692 * Starts transmitting the current TD's for recording/playing. 1693 * For playback, ALSA has filled the DMA memory with new data (we hope). 1694 */ 1695 static void xmit_descs(struct snd_dbri *dbri) 1696 { 1697 struct dbri_streaminfo *info; 1698 s32 *cmd; 1699 unsigned long flags; 1700 int first_td; 1701 1702 if (dbri == NULL) 1703 return; /* Disabled */ 1704 1705 info = &dbri->stream_info[DBRI_REC]; 1706 spin_lock_irqsave(&dbri->lock, flags); 1707 1708 if (info->pipe >= 0) { 1709 first_td = dbri->pipes[info->pipe].first_desc; 1710 1711 dprintk(D_DESC, "xmit_descs rec @ TD %d\n", first_td); 1712 1713 /* Stream could be closed by the time we run. */ 1714 if (first_td >= 0) { 1715 cmd = dbri_cmdlock(dbri, 2); 1716 *(cmd++) = DBRI_CMD(D_SDP, 0, 1717 dbri->pipes[info->pipe].sdp 1718 | D_SDP_P | D_SDP_EVERY | D_SDP_C); 1719 *(cmd++) = dbri->dma_dvma + 1720 dbri_dma_off(desc, first_td); 1721 dbri_cmdsend(dbri, cmd, 2); 1722 1723 /* Reset our admin of the pipe. */ 1724 dbri->pipes[info->pipe].desc = first_td; 1725 } 1726 } 1727 1728 info = &dbri->stream_info[DBRI_PLAY]; 1729 1730 if (info->pipe >= 0) { 1731 first_td = dbri->pipes[info->pipe].first_desc; 1732 1733 dprintk(D_DESC, "xmit_descs play @ TD %d\n", first_td); 1734 1735 /* Stream could be closed by the time we run. */ 1736 if (first_td >= 0) { 1737 cmd = dbri_cmdlock(dbri, 2); 1738 *(cmd++) = DBRI_CMD(D_SDP, 0, 1739 dbri->pipes[info->pipe].sdp 1740 | D_SDP_P | D_SDP_EVERY | D_SDP_C); 1741 *(cmd++) = dbri->dma_dvma + 1742 dbri_dma_off(desc, first_td); 1743 dbri_cmdsend(dbri, cmd, 2); 1744 1745 /* Reset our admin of the pipe. */ 1746 dbri->pipes[info->pipe].desc = first_td; 1747 } 1748 } 1749 1750 spin_unlock_irqrestore(&dbri->lock, flags); 1751 } 1752 1753 /* transmission_complete_intr() 1754 * 1755 * Called by main interrupt handler when DBRI signals transmission complete 1756 * on a pipe (interrupt triggered by the B bit in a transmit descriptor). 1757 * 1758 * Walks through the pipe's list of transmit buffer descriptors and marks 1759 * them as available. Stops when the first descriptor is found without 1760 * TBC (Transmit Buffer Complete) set, or we've run through them all. 1761 * 1762 * The DMA buffers are not released. They form a ring buffer and 1763 * they are filled by ALSA while others are transmitted by DMA. 1764 * 1765 */ 1766 1767 static void transmission_complete_intr(struct snd_dbri *dbri, int pipe) 1768 { 1769 struct dbri_streaminfo *info = &dbri->stream_info[DBRI_PLAY]; 1770 int td = dbri->pipes[pipe].desc; 1771 int status; 1772 1773 while (td >= 0) { 1774 if (td >= DBRI_NO_DESCS) { 1775 printk(KERN_ERR "DBRI: invalid td on pipe %d\n", pipe); 1776 return; 1777 } 1778 1779 status = DBRI_TD_STATUS(dbri->dma->desc[td].word4); 1780 if (!(status & DBRI_TD_TBC)) 1781 break; 1782 1783 dprintk(D_INT, "TD %d, status 0x%02x\n", td, status); 1784 1785 dbri->dma->desc[td].word4 = 0; /* Reset it for next time. */ 1786 info->offset += DBRI_RD_CNT(dbri->dma->desc[td].word1); 1787 1788 td = dbri->next_desc[td]; 1789 dbri->pipes[pipe].desc = td; 1790 } 1791 1792 /* Notify ALSA */ 1793 spin_unlock(&dbri->lock); 1794 snd_pcm_period_elapsed(info->substream); 1795 spin_lock(&dbri->lock); 1796 } 1797 1798 static void reception_complete_intr(struct snd_dbri *dbri, int pipe) 1799 { 1800 struct dbri_streaminfo *info; 1801 int rd = dbri->pipes[pipe].desc; 1802 s32 status; 1803 1804 if (rd < 0 || rd >= DBRI_NO_DESCS) { 1805 printk(KERN_ERR "DBRI: invalid rd on pipe %d\n", pipe); 1806 return; 1807 } 1808 1809 dbri->pipes[pipe].desc = dbri->next_desc[rd]; 1810 status = dbri->dma->desc[rd].word1; 1811 dbri->dma->desc[rd].word1 = 0; /* Reset it for next time. */ 1812 1813 info = &dbri->stream_info[DBRI_REC]; 1814 info->offset += DBRI_RD_CNT(status); 1815 1816 /* FIXME: Check status */ 1817 1818 dprintk(D_INT, "Recv RD %d, status 0x%02x, len %d\n", 1819 rd, DBRI_RD_STATUS(status), DBRI_RD_CNT(status)); 1820 1821 /* Notify ALSA */ 1822 spin_unlock(&dbri->lock); 1823 snd_pcm_period_elapsed(info->substream); 1824 spin_lock(&dbri->lock); 1825 } 1826 1827 static void dbri_process_one_interrupt(struct snd_dbri *dbri, int x) 1828 { 1829 int val = D_INTR_GETVAL(x); 1830 int channel = D_INTR_GETCHAN(x); 1831 int command = D_INTR_GETCMD(x); 1832 int code = D_INTR_GETCODE(x); 1833 #ifdef DBRI_DEBUG 1834 int rval = D_INTR_GETRVAL(x); 1835 #endif 1836 1837 if (channel == D_INTR_CMD) { 1838 dprintk(D_CMD, "INTR: Command: %-5s Value:%d\n", 1839 cmds[command], val); 1840 } else { 1841 dprintk(D_INT, "INTR: Chan:%d Code:%d Val:%#x\n", 1842 channel, code, rval); 1843 } 1844 1845 switch (code) { 1846 case D_INTR_CMDI: 1847 if (command != D_WAIT) 1848 printk(KERN_ERR "DBRI: Command read interrupt\n"); 1849 break; 1850 case D_INTR_BRDY: 1851 reception_complete_intr(dbri, channel); 1852 break; 1853 case D_INTR_XCMP: 1854 case D_INTR_MINT: 1855 transmission_complete_intr(dbri, channel); 1856 break; 1857 case D_INTR_UNDR: 1858 /* UNDR - Transmission underrun 1859 * resend SDP command with clear pipe bit (C) set 1860 */ 1861 { 1862 /* FIXME: do something useful in case of underrun */ 1863 printk(KERN_ERR "DBRI: Underrun error\n"); 1864 #if 0 1865 s32 *cmd; 1866 int pipe = channel; 1867 int td = dbri->pipes[pipe].desc; 1868 1869 dbri->dma->desc[td].word4 = 0; 1870 cmd = dbri_cmdlock(dbri, NoGetLock); 1871 *(cmd++) = DBRI_CMD(D_SDP, 0, 1872 dbri->pipes[pipe].sdp 1873 | D_SDP_P | D_SDP_C | D_SDP_2SAME); 1874 *(cmd++) = dbri->dma_dvma + dbri_dma_off(desc, td); 1875 dbri_cmdsend(dbri, cmd); 1876 #endif 1877 } 1878 break; 1879 case D_INTR_FXDT: 1880 /* FXDT - Fixed data change */ 1881 if (dbri->pipes[channel].sdp & D_SDP_MSB) 1882 val = reverse_bytes(val, dbri->pipes[channel].length); 1883 1884 if (dbri->pipes[channel].recv_fixed_ptr) 1885 *(dbri->pipes[channel].recv_fixed_ptr) = val; 1886 break; 1887 default: 1888 if (channel != D_INTR_CMD) 1889 printk(KERN_WARNING 1890 "DBRI: Ignored Interrupt: %d (0x%x)\n", code, x); 1891 } 1892 } 1893 1894 /* dbri_process_interrupt_buffer advances through the DBRI's interrupt 1895 * buffer until it finds a zero word (indicating nothing more to do 1896 * right now). Non-zero words require processing and are handed off 1897 * to dbri_process_one_interrupt AFTER advancing the pointer. 1898 */ 1899 static void dbri_process_interrupt_buffer(struct snd_dbri *dbri) 1900 { 1901 s32 x; 1902 1903 while ((x = dbri->dma->intr[dbri->dbri_irqp]) != 0) { 1904 dbri->dma->intr[dbri->dbri_irqp] = 0; 1905 dbri->dbri_irqp++; 1906 if (dbri->dbri_irqp == DBRI_INT_BLK) 1907 dbri->dbri_irqp = 1; 1908 1909 dbri_process_one_interrupt(dbri, x); 1910 } 1911 } 1912 1913 static irqreturn_t snd_dbri_interrupt(int irq, void *dev_id) 1914 { 1915 struct snd_dbri *dbri = dev_id; 1916 static int errcnt = 0; 1917 int x; 1918 1919 if (dbri == NULL) 1920 return IRQ_NONE; 1921 spin_lock(&dbri->lock); 1922 1923 /* 1924 * Read it, so the interrupt goes away. 1925 */ 1926 x = sbus_readl(dbri->regs + REG1); 1927 1928 if (x & (D_MRR | D_MLE | D_LBG | D_MBE)) { 1929 u32 tmp; 1930 1931 if (x & D_MRR) 1932 printk(KERN_ERR 1933 "DBRI: Multiple Error Ack on SBus reg1=0x%x\n", 1934 x); 1935 if (x & D_MLE) 1936 printk(KERN_ERR 1937 "DBRI: Multiple Late Error on SBus reg1=0x%x\n", 1938 x); 1939 if (x & D_LBG) 1940 printk(KERN_ERR 1941 "DBRI: Lost Bus Grant on SBus reg1=0x%x\n", x); 1942 if (x & D_MBE) 1943 printk(KERN_ERR 1944 "DBRI: Burst Error on SBus reg1=0x%x\n", x); 1945 1946 /* Some of these SBus errors cause the chip's SBus circuitry 1947 * to be disabled, so just re-enable and try to keep going. 1948 * 1949 * The only one I've seen is MRR, which will be triggered 1950 * if you let a transmit pipe underrun, then try to CDP it. 1951 * 1952 * If these things persist, we reset the chip. 1953 */ 1954 if ((++errcnt) % 10 == 0) { 1955 dprintk(D_INT, "Interrupt errors exceeded.\n"); 1956 dbri_reset(dbri); 1957 } else { 1958 tmp = sbus_readl(dbri->regs + REG0); 1959 tmp &= ~(D_D); 1960 sbus_writel(tmp, dbri->regs + REG0); 1961 } 1962 } 1963 1964 dbri_process_interrupt_buffer(dbri); 1965 1966 spin_unlock(&dbri->lock); 1967 1968 return IRQ_HANDLED; 1969 } 1970 1971 /**************************************************************************** 1972 PCM Interface 1973 ****************************************************************************/ 1974 static struct snd_pcm_hardware snd_dbri_pcm_hw = { 1975 .info = SNDRV_PCM_INFO_MMAP | 1976 SNDRV_PCM_INFO_INTERLEAVED | 1977 SNDRV_PCM_INFO_BLOCK_TRANSFER | 1978 SNDRV_PCM_INFO_MMAP_VALID | 1979 SNDRV_PCM_INFO_BATCH, 1980 .formats = SNDRV_PCM_FMTBIT_MU_LAW | 1981 SNDRV_PCM_FMTBIT_A_LAW | 1982 SNDRV_PCM_FMTBIT_U8 | 1983 SNDRV_PCM_FMTBIT_S16_BE, 1984 .rates = SNDRV_PCM_RATE_8000_48000 | SNDRV_PCM_RATE_5512, 1985 .rate_min = 5512, 1986 .rate_max = 48000, 1987 .channels_min = 1, 1988 .channels_max = 2, 1989 .buffer_bytes_max = 64 * 1024, 1990 .period_bytes_min = 1, 1991 .period_bytes_max = DBRI_TD_MAXCNT, 1992 .periods_min = 1, 1993 .periods_max = 1024, 1994 }; 1995 1996 static int snd_hw_rule_format(struct snd_pcm_hw_params *params, 1997 struct snd_pcm_hw_rule *rule) 1998 { 1999 struct snd_interval *c = hw_param_interval(params, 2000 SNDRV_PCM_HW_PARAM_CHANNELS); 2001 struct snd_mask *f = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT); 2002 struct snd_mask fmt; 2003 2004 snd_mask_any(&fmt); 2005 if (c->min > 1) { 2006 fmt.bits[0] &= SNDRV_PCM_FMTBIT_S16_BE; 2007 return snd_mask_refine(f, &fmt); 2008 } 2009 return 0; 2010 } 2011 2012 static int snd_hw_rule_channels(struct snd_pcm_hw_params *params, 2013 struct snd_pcm_hw_rule *rule) 2014 { 2015 struct snd_interval *c = hw_param_interval(params, 2016 SNDRV_PCM_HW_PARAM_CHANNELS); 2017 struct snd_mask *f = hw_param_mask(params, SNDRV_PCM_HW_PARAM_FORMAT); 2018 struct snd_interval ch; 2019 2020 snd_interval_any(&ch); 2021 if (!(f->bits[0] & SNDRV_PCM_FMTBIT_S16_BE)) { 2022 ch.min = 1; 2023 ch.max = 1; 2024 ch.integer = 1; 2025 return snd_interval_refine(c, &ch); 2026 } 2027 return 0; 2028 } 2029 2030 static int snd_dbri_open(struct snd_pcm_substream *substream) 2031 { 2032 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2033 struct snd_pcm_runtime *runtime = substream->runtime; 2034 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2035 unsigned long flags; 2036 2037 dprintk(D_USR, "open audio output.\n"); 2038 runtime->hw = snd_dbri_pcm_hw; 2039 2040 spin_lock_irqsave(&dbri->lock, flags); 2041 info->substream = substream; 2042 info->offset = 0; 2043 info->dvma_buffer = 0; 2044 info->pipe = -1; 2045 spin_unlock_irqrestore(&dbri->lock, flags); 2046 2047 snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, 2048 snd_hw_rule_format, NULL, SNDRV_PCM_HW_PARAM_FORMAT, 2049 -1); 2050 snd_pcm_hw_rule_add(runtime, 0, SNDRV_PCM_HW_PARAM_FORMAT, 2051 snd_hw_rule_channels, NULL, 2052 SNDRV_PCM_HW_PARAM_CHANNELS, 2053 -1); 2054 2055 cs4215_open(dbri); 2056 2057 return 0; 2058 } 2059 2060 static int snd_dbri_close(struct snd_pcm_substream *substream) 2061 { 2062 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2063 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2064 2065 dprintk(D_USR, "close audio output.\n"); 2066 info->substream = NULL; 2067 info->offset = 0; 2068 2069 return 0; 2070 } 2071 2072 static int snd_dbri_hw_params(struct snd_pcm_substream *substream, 2073 struct snd_pcm_hw_params *hw_params) 2074 { 2075 struct snd_pcm_runtime *runtime = substream->runtime; 2076 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2077 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2078 int direction; 2079 int ret; 2080 2081 /* set sampling rate, audio format and number of channels */ 2082 ret = cs4215_prepare(dbri, params_rate(hw_params), 2083 params_format(hw_params), 2084 params_channels(hw_params)); 2085 if (ret != 0) 2086 return ret; 2087 2088 if ((ret = snd_pcm_lib_malloc_pages(substream, 2089 params_buffer_bytes(hw_params))) < 0) { 2090 printk(KERN_ERR "malloc_pages failed with %d\n", ret); 2091 return ret; 2092 } 2093 2094 /* hw_params can get called multiple times. Only map the DMA once. 2095 */ 2096 if (info->dvma_buffer == 0) { 2097 if (DBRI_STREAMNO(substream) == DBRI_PLAY) 2098 direction = DMA_TO_DEVICE; 2099 else 2100 direction = DMA_FROM_DEVICE; 2101 2102 info->dvma_buffer = 2103 dma_map_single(&dbri->op->dev, 2104 runtime->dma_area, 2105 params_buffer_bytes(hw_params), 2106 direction); 2107 } 2108 2109 direction = params_buffer_bytes(hw_params); 2110 dprintk(D_USR, "hw_params: %d bytes, dvma=%x\n", 2111 direction, info->dvma_buffer); 2112 return 0; 2113 } 2114 2115 static int snd_dbri_hw_free(struct snd_pcm_substream *substream) 2116 { 2117 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2118 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2119 int direction; 2120 2121 dprintk(D_USR, "hw_free.\n"); 2122 2123 /* hw_free can get called multiple times. Only unmap the DMA once. 2124 */ 2125 if (info->dvma_buffer) { 2126 if (DBRI_STREAMNO(substream) == DBRI_PLAY) 2127 direction = DMA_TO_DEVICE; 2128 else 2129 direction = DMA_FROM_DEVICE; 2130 2131 dma_unmap_single(&dbri->op->dev, info->dvma_buffer, 2132 substream->runtime->buffer_size, direction); 2133 info->dvma_buffer = 0; 2134 } 2135 if (info->pipe != -1) { 2136 reset_pipe(dbri, info->pipe); 2137 info->pipe = -1; 2138 } 2139 2140 return snd_pcm_lib_free_pages(substream); 2141 } 2142 2143 static int snd_dbri_prepare(struct snd_pcm_substream *substream) 2144 { 2145 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2146 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2147 int ret; 2148 2149 info->size = snd_pcm_lib_buffer_bytes(substream); 2150 if (DBRI_STREAMNO(substream) == DBRI_PLAY) 2151 info->pipe = 4; /* Send pipe */ 2152 else 2153 info->pipe = 6; /* Receive pipe */ 2154 2155 spin_lock_irq(&dbri->lock); 2156 info->offset = 0; 2157 2158 /* Setup the all the transmit/receive descriptors to cover the 2159 * whole DMA buffer. 2160 */ 2161 ret = setup_descs(dbri, DBRI_STREAMNO(substream), 2162 snd_pcm_lib_period_bytes(substream)); 2163 2164 spin_unlock_irq(&dbri->lock); 2165 2166 dprintk(D_USR, "prepare audio output. %d bytes\n", info->size); 2167 return ret; 2168 } 2169 2170 static int snd_dbri_trigger(struct snd_pcm_substream *substream, int cmd) 2171 { 2172 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2173 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2174 int ret = 0; 2175 2176 switch (cmd) { 2177 case SNDRV_PCM_TRIGGER_START: 2178 dprintk(D_USR, "start audio, period is %d bytes\n", 2179 (int)snd_pcm_lib_period_bytes(substream)); 2180 /* Re-submit the TDs. */ 2181 xmit_descs(dbri); 2182 break; 2183 case SNDRV_PCM_TRIGGER_STOP: 2184 dprintk(D_USR, "stop audio.\n"); 2185 reset_pipe(dbri, info->pipe); 2186 break; 2187 default: 2188 ret = -EINVAL; 2189 } 2190 2191 return ret; 2192 } 2193 2194 static snd_pcm_uframes_t snd_dbri_pointer(struct snd_pcm_substream *substream) 2195 { 2196 struct snd_dbri *dbri = snd_pcm_substream_chip(substream); 2197 struct dbri_streaminfo *info = DBRI_STREAM(dbri, substream); 2198 snd_pcm_uframes_t ret; 2199 2200 ret = bytes_to_frames(substream->runtime, info->offset) 2201 % substream->runtime->buffer_size; 2202 dprintk(D_USR, "I/O pointer: %ld frames of %ld.\n", 2203 ret, substream->runtime->buffer_size); 2204 return ret; 2205 } 2206 2207 static struct snd_pcm_ops snd_dbri_ops = { 2208 .open = snd_dbri_open, 2209 .close = snd_dbri_close, 2210 .ioctl = snd_pcm_lib_ioctl, 2211 .hw_params = snd_dbri_hw_params, 2212 .hw_free = snd_dbri_hw_free, 2213 .prepare = snd_dbri_prepare, 2214 .trigger = snd_dbri_trigger, 2215 .pointer = snd_dbri_pointer, 2216 }; 2217 2218 static int __devinit snd_dbri_pcm(struct snd_card *card) 2219 { 2220 struct snd_pcm *pcm; 2221 int err; 2222 2223 if ((err = snd_pcm_new(card, 2224 /* ID */ "sun_dbri", 2225 /* device */ 0, 2226 /* playback count */ 1, 2227 /* capture count */ 1, &pcm)) < 0) 2228 return err; 2229 2230 snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_PLAYBACK, &snd_dbri_ops); 2231 snd_pcm_set_ops(pcm, SNDRV_PCM_STREAM_CAPTURE, &snd_dbri_ops); 2232 2233 pcm->private_data = card->private_data; 2234 pcm->info_flags = 0; 2235 strcpy(pcm->name, card->shortname); 2236 2237 if ((err = snd_pcm_lib_preallocate_pages_for_all(pcm, 2238 SNDRV_DMA_TYPE_CONTINUOUS, 2239 snd_dma_continuous_data(GFP_KERNEL), 2240 64 * 1024, 64 * 1024)) < 0) 2241 return err; 2242 2243 return 0; 2244 } 2245 2246 /***************************************************************************** 2247 Mixer interface 2248 *****************************************************************************/ 2249 2250 static int snd_cs4215_info_volume(struct snd_kcontrol *kcontrol, 2251 struct snd_ctl_elem_info *uinfo) 2252 { 2253 uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; 2254 uinfo->count = 2; 2255 uinfo->value.integer.min = 0; 2256 if (kcontrol->private_value == DBRI_PLAY) 2257 uinfo->value.integer.max = DBRI_MAX_VOLUME; 2258 else 2259 uinfo->value.integer.max = DBRI_MAX_GAIN; 2260 return 0; 2261 } 2262 2263 static int snd_cs4215_get_volume(struct snd_kcontrol *kcontrol, 2264 struct snd_ctl_elem_value *ucontrol) 2265 { 2266 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2267 struct dbri_streaminfo *info; 2268 2269 if (snd_BUG_ON(!dbri)) 2270 return -EINVAL; 2271 info = &dbri->stream_info[kcontrol->private_value]; 2272 2273 ucontrol->value.integer.value[0] = info->left_gain; 2274 ucontrol->value.integer.value[1] = info->right_gain; 2275 return 0; 2276 } 2277 2278 static int snd_cs4215_put_volume(struct snd_kcontrol *kcontrol, 2279 struct snd_ctl_elem_value *ucontrol) 2280 { 2281 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2282 struct dbri_streaminfo *info = 2283 &dbri->stream_info[kcontrol->private_value]; 2284 unsigned int vol[2]; 2285 int changed = 0; 2286 2287 vol[0] = ucontrol->value.integer.value[0]; 2288 vol[1] = ucontrol->value.integer.value[1]; 2289 if (kcontrol->private_value == DBRI_PLAY) { 2290 if (vol[0] > DBRI_MAX_VOLUME || vol[1] > DBRI_MAX_VOLUME) 2291 return -EINVAL; 2292 } else { 2293 if (vol[0] > DBRI_MAX_GAIN || vol[1] > DBRI_MAX_GAIN) 2294 return -EINVAL; 2295 } 2296 2297 if (info->left_gain != vol[0]) { 2298 info->left_gain = vol[0]; 2299 changed = 1; 2300 } 2301 if (info->right_gain != vol[1]) { 2302 info->right_gain = vol[1]; 2303 changed = 1; 2304 } 2305 if (changed) { 2306 /* First mute outputs, and wait 1/8000 sec (125 us) 2307 * to make sure this takes. This avoids clicking noises. 2308 */ 2309 cs4215_setdata(dbri, 1); 2310 udelay(125); 2311 cs4215_setdata(dbri, 0); 2312 } 2313 return changed; 2314 } 2315 2316 static int snd_cs4215_info_single(struct snd_kcontrol *kcontrol, 2317 struct snd_ctl_elem_info *uinfo) 2318 { 2319 int mask = (kcontrol->private_value >> 16) & 0xff; 2320 2321 uinfo->type = (mask == 1) ? 2322 SNDRV_CTL_ELEM_TYPE_BOOLEAN : SNDRV_CTL_ELEM_TYPE_INTEGER; 2323 uinfo->count = 1; 2324 uinfo->value.integer.min = 0; 2325 uinfo->value.integer.max = mask; 2326 return 0; 2327 } 2328 2329 static int snd_cs4215_get_single(struct snd_kcontrol *kcontrol, 2330 struct snd_ctl_elem_value *ucontrol) 2331 { 2332 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2333 int elem = kcontrol->private_value & 0xff; 2334 int shift = (kcontrol->private_value >> 8) & 0xff; 2335 int mask = (kcontrol->private_value >> 16) & 0xff; 2336 int invert = (kcontrol->private_value >> 24) & 1; 2337 2338 if (snd_BUG_ON(!dbri)) 2339 return -EINVAL; 2340 2341 if (elem < 4) 2342 ucontrol->value.integer.value[0] = 2343 (dbri->mm.data[elem] >> shift) & mask; 2344 else 2345 ucontrol->value.integer.value[0] = 2346 (dbri->mm.ctrl[elem - 4] >> shift) & mask; 2347 2348 if (invert == 1) 2349 ucontrol->value.integer.value[0] = 2350 mask - ucontrol->value.integer.value[0]; 2351 return 0; 2352 } 2353 2354 static int snd_cs4215_put_single(struct snd_kcontrol *kcontrol, 2355 struct snd_ctl_elem_value *ucontrol) 2356 { 2357 struct snd_dbri *dbri = snd_kcontrol_chip(kcontrol); 2358 int elem = kcontrol->private_value & 0xff; 2359 int shift = (kcontrol->private_value >> 8) & 0xff; 2360 int mask = (kcontrol->private_value >> 16) & 0xff; 2361 int invert = (kcontrol->private_value >> 24) & 1; 2362 int changed = 0; 2363 unsigned short val; 2364 2365 if (snd_BUG_ON(!dbri)) 2366 return -EINVAL; 2367 2368 val = (ucontrol->value.integer.value[0] & mask); 2369 if (invert == 1) 2370 val = mask - val; 2371 val <<= shift; 2372 2373 if (elem < 4) { 2374 dbri->mm.data[elem] = (dbri->mm.data[elem] & 2375 ~(mask << shift)) | val; 2376 changed = (val != dbri->mm.data[elem]); 2377 } else { 2378 dbri->mm.ctrl[elem - 4] = (dbri->mm.ctrl[elem - 4] & 2379 ~(mask << shift)) | val; 2380 changed = (val != dbri->mm.ctrl[elem - 4]); 2381 } 2382 2383 dprintk(D_GEN, "put_single: mask=0x%x, changed=%d, " 2384 "mixer-value=%ld, mm-value=0x%x\n", 2385 mask, changed, ucontrol->value.integer.value[0], 2386 dbri->mm.data[elem & 3]); 2387 2388 if (changed) { 2389 /* First mute outputs, and wait 1/8000 sec (125 us) 2390 * to make sure this takes. This avoids clicking noises. 2391 */ 2392 cs4215_setdata(dbri, 1); 2393 udelay(125); 2394 cs4215_setdata(dbri, 0); 2395 } 2396 return changed; 2397 } 2398 2399 /* Entries 0-3 map to the 4 data timeslots, entries 4-7 map to the 4 control 2400 timeslots. Shift is the bit offset in the timeslot, mask defines the 2401 number of bits. invert is a boolean for use with attenuation. 2402 */ 2403 #define CS4215_SINGLE(xname, entry, shift, mask, invert) \ 2404 { .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname), \ 2405 .info = snd_cs4215_info_single, \ 2406 .get = snd_cs4215_get_single, .put = snd_cs4215_put_single, \ 2407 .private_value = (entry) | ((shift) << 8) | ((mask) << 16) | \ 2408 ((invert) << 24) }, 2409 2410 static struct snd_kcontrol_new dbri_controls[] __devinitdata = { 2411 { 2412 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 2413 .name = "Playback Volume", 2414 .info = snd_cs4215_info_volume, 2415 .get = snd_cs4215_get_volume, 2416 .put = snd_cs4215_put_volume, 2417 .private_value = DBRI_PLAY, 2418 }, 2419 CS4215_SINGLE("Headphone switch", 0, 7, 1, 0) 2420 CS4215_SINGLE("Line out switch", 0, 6, 1, 0) 2421 CS4215_SINGLE("Speaker switch", 1, 6, 1, 0) 2422 { 2423 .iface = SNDRV_CTL_ELEM_IFACE_MIXER, 2424 .name = "Capture Volume", 2425 .info = snd_cs4215_info_volume, 2426 .get = snd_cs4215_get_volume, 2427 .put = snd_cs4215_put_volume, 2428 .private_value = DBRI_REC, 2429 }, 2430 /* FIXME: mic/line switch */ 2431 CS4215_SINGLE("Line in switch", 2, 4, 1, 0) 2432 CS4215_SINGLE("High Pass Filter switch", 5, 7, 1, 0) 2433 CS4215_SINGLE("Monitor Volume", 3, 4, 0xf, 1) 2434 CS4215_SINGLE("Mic boost", 4, 4, 1, 1) 2435 }; 2436 2437 static int __devinit snd_dbri_mixer(struct snd_card *card) 2438 { 2439 int idx, err; 2440 struct snd_dbri *dbri; 2441 2442 if (snd_BUG_ON(!card || !card->private_data)) 2443 return -EINVAL; 2444 dbri = card->private_data; 2445 2446 strcpy(card->mixername, card->shortname); 2447 2448 for (idx = 0; idx < ARRAY_SIZE(dbri_controls); idx++) { 2449 err = snd_ctl_add(card, 2450 snd_ctl_new1(&dbri_controls[idx], dbri)); 2451 if (err < 0) 2452 return err; 2453 } 2454 2455 for (idx = DBRI_REC; idx < DBRI_NO_STREAMS; idx++) { 2456 dbri->stream_info[idx].left_gain = 0; 2457 dbri->stream_info[idx].right_gain = 0; 2458 } 2459 2460 return 0; 2461 } 2462 2463 /**************************************************************************** 2464 /proc interface 2465 ****************************************************************************/ 2466 static void dbri_regs_read(struct snd_info_entry *entry, 2467 struct snd_info_buffer *buffer) 2468 { 2469 struct snd_dbri *dbri = entry->private_data; 2470 2471 snd_iprintf(buffer, "REG0: 0x%x\n", sbus_readl(dbri->regs + REG0)); 2472 snd_iprintf(buffer, "REG2: 0x%x\n", sbus_readl(dbri->regs + REG2)); 2473 snd_iprintf(buffer, "REG8: 0x%x\n", sbus_readl(dbri->regs + REG8)); 2474 snd_iprintf(buffer, "REG9: 0x%x\n", sbus_readl(dbri->regs + REG9)); 2475 } 2476 2477 #ifdef DBRI_DEBUG 2478 static void dbri_debug_read(struct snd_info_entry *entry, 2479 struct snd_info_buffer *buffer) 2480 { 2481 struct snd_dbri *dbri = entry->private_data; 2482 int pipe; 2483 snd_iprintf(buffer, "debug=%d\n", dbri_debug); 2484 2485 for (pipe = 0; pipe < 32; pipe++) { 2486 if (pipe_active(dbri, pipe)) { 2487 struct dbri_pipe *pptr = &dbri->pipes[pipe]; 2488 snd_iprintf(buffer, 2489 "Pipe %d: %s SDP=0x%x desc=%d, " 2490 "len=%d next %d\n", 2491 pipe, 2492 (pptr->sdp & D_SDP_TO_SER) ? "output" : 2493 "input", 2494 pptr->sdp, pptr->desc, 2495 pptr->length, pptr->nextpipe); 2496 } 2497 } 2498 } 2499 #endif 2500 2501 static void __devinit snd_dbri_proc(struct snd_card *card) 2502 { 2503 struct snd_dbri *dbri = card->private_data; 2504 struct snd_info_entry *entry; 2505 2506 if (!snd_card_proc_new(card, "regs", &entry)) 2507 snd_info_set_text_ops(entry, dbri, dbri_regs_read); 2508 2509 #ifdef DBRI_DEBUG 2510 if (!snd_card_proc_new(card, "debug", &entry)) { 2511 snd_info_set_text_ops(entry, dbri, dbri_debug_read); 2512 entry->mode = S_IFREG | S_IRUGO; /* Readable only. */ 2513 } 2514 #endif 2515 } 2516 2517 /* 2518 **************************************************************************** 2519 **************************** Initialization ******************************** 2520 **************************************************************************** 2521 */ 2522 static void snd_dbri_free(struct snd_dbri *dbri); 2523 2524 static int __devinit snd_dbri_create(struct snd_card *card, 2525 struct of_device *op, 2526 int irq, int dev) 2527 { 2528 struct snd_dbri *dbri = card->private_data; 2529 int err; 2530 2531 spin_lock_init(&dbri->lock); 2532 dbri->op = op; 2533 dbri->irq = irq; 2534 2535 dbri->dma = dma_alloc_coherent(&op->dev, 2536 sizeof(struct dbri_dma), 2537 &dbri->dma_dvma, GFP_ATOMIC); 2538 if (!dbri->dma) 2539 return -ENOMEM; 2540 memset((void *)dbri->dma, 0, sizeof(struct dbri_dma)); 2541 2542 dprintk(D_GEN, "DMA Cmd Block 0x%p (0x%08x)\n", 2543 dbri->dma, dbri->dma_dvma); 2544 2545 /* Map the registers into memory. */ 2546 dbri->regs_size = resource_size(&op->resource[0]); 2547 dbri->regs = of_ioremap(&op->resource[0], 0, 2548 dbri->regs_size, "DBRI Registers"); 2549 if (!dbri->regs) { 2550 printk(KERN_ERR "DBRI: could not allocate registers\n"); 2551 dma_free_coherent(&op->dev, sizeof(struct dbri_dma), 2552 (void *)dbri->dma, dbri->dma_dvma); 2553 return -EIO; 2554 } 2555 2556 err = request_irq(dbri->irq, snd_dbri_interrupt, IRQF_SHARED, 2557 "DBRI audio", dbri); 2558 if (err) { 2559 printk(KERN_ERR "DBRI: Can't get irq %d\n", dbri->irq); 2560 of_iounmap(&op->resource[0], dbri->regs, dbri->regs_size); 2561 dma_free_coherent(&op->dev, sizeof(struct dbri_dma), 2562 (void *)dbri->dma, dbri->dma_dvma); 2563 return err; 2564 } 2565 2566 /* Do low level initialization of the DBRI and CS4215 chips */ 2567 dbri_initialize(dbri); 2568 err = cs4215_init(dbri); 2569 if (err) { 2570 snd_dbri_free(dbri); 2571 return err; 2572 } 2573 2574 return 0; 2575 } 2576 2577 static void snd_dbri_free(struct snd_dbri *dbri) 2578 { 2579 dprintk(D_GEN, "snd_dbri_free\n"); 2580 dbri_reset(dbri); 2581 2582 if (dbri->irq) 2583 free_irq(dbri->irq, dbri); 2584 2585 if (dbri->regs) 2586 of_iounmap(&dbri->op->resource[0], dbri->regs, dbri->regs_size); 2587 2588 if (dbri->dma) 2589 dma_free_coherent(&dbri->op->dev, 2590 sizeof(struct dbri_dma), 2591 (void *)dbri->dma, dbri->dma_dvma); 2592 } 2593 2594 static int __devinit dbri_probe(struct of_device *op, const struct of_device_id *match) 2595 { 2596 struct snd_dbri *dbri; 2597 struct resource *rp; 2598 struct snd_card *card; 2599 static int dev = 0; 2600 int irq; 2601 int err; 2602 2603 if (dev >= SNDRV_CARDS) 2604 return -ENODEV; 2605 if (!enable[dev]) { 2606 dev++; 2607 return -ENOENT; 2608 } 2609 2610 irq = op->irqs[0]; 2611 if (irq <= 0) { 2612 printk(KERN_ERR "DBRI-%d: No IRQ.\n", dev); 2613 return -ENODEV; 2614 } 2615 2616 err = snd_card_create(index[dev], id[dev], THIS_MODULE, 2617 sizeof(struct snd_dbri), &card); 2618 if (err < 0) 2619 return err; 2620 2621 strcpy(card->driver, "DBRI"); 2622 strcpy(card->shortname, "Sun DBRI"); 2623 rp = &op->resource[0]; 2624 sprintf(card->longname, "%s at 0x%02lx:0x%016Lx, irq %d", 2625 card->shortname, 2626 rp->flags & 0xffL, (unsigned long long)rp->start, irq); 2627 2628 err = snd_dbri_create(card, op, irq, dev); 2629 if (err < 0) { 2630 snd_card_free(card); 2631 return err; 2632 } 2633 2634 dbri = card->private_data; 2635 err = snd_dbri_pcm(card); 2636 if (err < 0) 2637 goto _err; 2638 2639 err = snd_dbri_mixer(card); 2640 if (err < 0) 2641 goto _err; 2642 2643 /* /proc file handling */ 2644 snd_dbri_proc(card); 2645 dev_set_drvdata(&op->dev, card); 2646 2647 err = snd_card_register(card); 2648 if (err < 0) 2649 goto _err; 2650 2651 printk(KERN_INFO "audio%d at %p (irq %d) is DBRI(%c)+CS4215(%d)\n", 2652 dev, dbri->regs, 2653 dbri->irq, op->node->name[9], dbri->mm.version); 2654 dev++; 2655 2656 return 0; 2657 2658 _err: 2659 snd_dbri_free(dbri); 2660 snd_card_free(card); 2661 return err; 2662 } 2663 2664 static int __devexit dbri_remove(struct of_device *op) 2665 { 2666 struct snd_card *card = dev_get_drvdata(&op->dev); 2667 2668 snd_dbri_free(card->private_data); 2669 snd_card_free(card); 2670 2671 dev_set_drvdata(&op->dev, NULL); 2672 2673 return 0; 2674 } 2675 2676 static const struct of_device_id dbri_match[] = { 2677 { 2678 .name = "SUNW,DBRIe", 2679 }, 2680 { 2681 .name = "SUNW,DBRIf", 2682 }, 2683 {}, 2684 }; 2685 2686 MODULE_DEVICE_TABLE(of, dbri_match); 2687 2688 static struct of_platform_driver dbri_sbus_driver = { 2689 .name = "dbri", 2690 .match_table = dbri_match, 2691 .probe = dbri_probe, 2692 .remove = __devexit_p(dbri_remove), 2693 }; 2694 2695 /* Probe for the dbri chip and then attach the driver. */ 2696 static int __init dbri_init(void) 2697 { 2698 return of_register_driver(&dbri_sbus_driver, &of_bus_type); 2699 } 2700 2701 static void __exit dbri_exit(void) 2702 { 2703 of_unregister_driver(&dbri_sbus_driver); 2704 } 2705 2706 module_init(dbri_init); 2707 module_exit(dbri_exit); 2708