1 // SPDX-License-Identifier: GPL-2.0
2 //
3 // Serial Sound Interface (I2S) support for SH7760/SH7780
4 //
5 // Copyright (c) 2007 Manuel Lauss <mano@roarinelk.homelinux.net>
6 //
7 // dont forget to set IPSEL/OMSEL register bits (in your board code) to
8 // enable SSI output pins!
9
10 /*
11 * LIMITATIONS:
12 * The SSI unit has only one physical data line, so full duplex is
13 * impossible. This can be remedied on the SH7760 by using the
14 * other SSI unit for recording; however the SH7780 has only 1 SSI
15 * unit, and its pins are shared with the AC97 unit, among others.
16 *
17 * FEATURES:
18 * The SSI features "compressed mode": in this mode it continuously
19 * streams PCM data over the I2S lines and uses LRCK as a handshake
20 * signal. Can be used to send compressed data (AC3/DTS) to a DSP.
21 * The number of bits sent over the wire in a frame can be adjusted
22 * and can be independent from the actual sample bit depth. This is
23 * useful to support TDM mode codecs like the AD1939 which have a
24 * fixed TDM slot size, regardless of sample resolution.
25 */
26
27 #include <linux/init.h>
28 #include <linux/module.h>
29 #include <linux/platform_device.h>
30 #include <sound/core.h>
31 #include <sound/pcm.h>
32 #include <sound/initval.h>
33 #include <sound/soc.h>
34 #include <asm/io.h>
35
36 #define SSICR 0x00
37 #define SSISR 0x04
38
39 #define CR_DMAEN (1 << 28)
40 #define CR_CHNL_SHIFT 22
41 #define CR_CHNL_MASK (3 << CR_CHNL_SHIFT)
42 #define CR_DWL_SHIFT 19
43 #define CR_DWL_MASK (7 << CR_DWL_SHIFT)
44 #define CR_SWL_SHIFT 16
45 #define CR_SWL_MASK (7 << CR_SWL_SHIFT)
46 #define CR_SCK_MASTER (1 << 15) /* bitclock master bit */
47 #define CR_SWS_MASTER (1 << 14) /* wordselect master bit */
48 #define CR_SCKP (1 << 13) /* I2Sclock polarity */
49 #define CR_SWSP (1 << 12) /* LRCK polarity */
50 #define CR_SPDP (1 << 11)
51 #define CR_SDTA (1 << 10) /* i2s alignment (msb/lsb) */
52 #define CR_PDTA (1 << 9) /* fifo data alignment */
53 #define CR_DEL (1 << 8) /* delay data by 1 i2sclk */
54 #define CR_BREN (1 << 7) /* clock gating in burst mode */
55 #define CR_CKDIV_SHIFT 4
56 #define CR_CKDIV_MASK (7 << CR_CKDIV_SHIFT) /* bitclock divider */
57 #define CR_MUTE (1 << 3) /* SSI mute */
58 #define CR_CPEN (1 << 2) /* compressed mode */
59 #define CR_TRMD (1 << 1) /* transmit/receive select */
60 #define CR_EN (1 << 0) /* enable SSI */
61
62 #define SSIREG(reg) (*(unsigned long *)(ssi->mmio + (reg)))
63
64 struct ssi_priv {
65 unsigned long mmio;
66 unsigned long sysclk;
67 int inuse;
68 } ssi_cpu_data[] = {
69 #if defined(CONFIG_CPU_SUBTYPE_SH7760)
70 {
71 .mmio = 0xFE680000,
72 },
73 {
74 .mmio = 0xFE690000,
75 },
76 #elif defined(CONFIG_CPU_SUBTYPE_SH7780)
77 {
78 .mmio = 0xFFE70000,
79 },
80 #else
81 #error "Unsupported SuperH SoC"
82 #endif
83 };
84
85 /*
86 * track usage of the SSI; it is simplex-only so prevent attempts of
87 * concurrent playback + capture. FIXME: any locking required?
88 */
ssi_startup(struct snd_pcm_substream * substream,struct snd_soc_dai * dai)89 static int ssi_startup(struct snd_pcm_substream *substream,
90 struct snd_soc_dai *dai)
91 {
92 struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
93 if (ssi->inuse) {
94 pr_debug("ssi: already in use!\n");
95 return -EBUSY;
96 } else
97 ssi->inuse = 1;
98 return 0;
99 }
100
ssi_shutdown(struct snd_pcm_substream * substream,struct snd_soc_dai * dai)101 static void ssi_shutdown(struct snd_pcm_substream *substream,
102 struct snd_soc_dai *dai)
103 {
104 struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
105
106 ssi->inuse = 0;
107 }
108
ssi_trigger(struct snd_pcm_substream * substream,int cmd,struct snd_soc_dai * dai)109 static int ssi_trigger(struct snd_pcm_substream *substream, int cmd,
110 struct snd_soc_dai *dai)
111 {
112 struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
113
114 switch (cmd) {
115 case SNDRV_PCM_TRIGGER_START:
116 SSIREG(SSICR) |= CR_DMAEN | CR_EN;
117 break;
118 case SNDRV_PCM_TRIGGER_STOP:
119 SSIREG(SSICR) &= ~(CR_DMAEN | CR_EN);
120 break;
121 default:
122 return -EINVAL;
123 }
124
125 return 0;
126 }
127
ssi_hw_params(struct snd_pcm_substream * substream,struct snd_pcm_hw_params * params,struct snd_soc_dai * dai)128 static int ssi_hw_params(struct snd_pcm_substream *substream,
129 struct snd_pcm_hw_params *params,
130 struct snd_soc_dai *dai)
131 {
132 struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
133 unsigned long ssicr = SSIREG(SSICR);
134 unsigned int bits, channels, swl, recv, i;
135
136 channels = params_channels(params);
137 bits = params->msbits;
138 recv = (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) ? 0 : 1;
139
140 pr_debug("ssi_hw_params() enter\nssicr was %08lx\n", ssicr);
141 pr_debug("bits: %u channels: %u\n", bits, channels);
142
143 ssicr &= ~(CR_TRMD | CR_CHNL_MASK | CR_DWL_MASK | CR_PDTA |
144 CR_SWL_MASK);
145
146 /* direction (send/receive) */
147 if (!recv)
148 ssicr |= CR_TRMD; /* transmit */
149
150 /* channels */
151 if ((channels < 2) || (channels > 8) || (channels & 1)) {
152 pr_debug("ssi: invalid number of channels\n");
153 return -EINVAL;
154 }
155 ssicr |= ((channels >> 1) - 1) << CR_CHNL_SHIFT;
156
157 /* DATA WORD LENGTH (DWL): databits in audio sample */
158 i = 0;
159 switch (bits) {
160 case 32: ++i;
161 case 24: ++i;
162 case 22: ++i;
163 case 20: ++i;
164 case 18: ++i;
165 case 16: ++i;
166 ssicr |= i << CR_DWL_SHIFT;
167 case 8: break;
168 default:
169 pr_debug("ssi: invalid sample width\n");
170 return -EINVAL;
171 }
172
173 /*
174 * SYSTEM WORD LENGTH: size in bits of half a frame over the I2S
175 * wires. This is usually bits_per_sample x channels/2; i.e. in
176 * Stereo mode the SWL equals DWL. SWL can be bigger than the
177 * product of (channels_per_slot x samplebits), e.g. for codecs
178 * like the AD1939 which only accept 32bit wide TDM slots. For
179 * "standard" I2S operation we set SWL = chans / 2 * DWL here.
180 * Waiting for ASoC to get TDM support ;-)
181 */
182 if ((bits > 16) && (bits <= 24)) {
183 bits = 24; /* these are padded by the SSI */
184 /*ssicr |= CR_PDTA;*/ /* cpu/data endianness ? */
185 }
186 i = 0;
187 swl = (bits * channels) / 2;
188 switch (swl) {
189 case 256: ++i;
190 case 128: ++i;
191 case 64: ++i;
192 case 48: ++i;
193 case 32: ++i;
194 case 16: ++i;
195 ssicr |= i << CR_SWL_SHIFT;
196 case 8: break;
197 default:
198 pr_debug("ssi: invalid system word length computed\n");
199 return -EINVAL;
200 }
201
202 SSIREG(SSICR) = ssicr;
203
204 pr_debug("ssi_hw_params() leave\nssicr is now %08lx\n", ssicr);
205 return 0;
206 }
207
ssi_set_sysclk(struct snd_soc_dai * cpu_dai,int clk_id,unsigned int freq,int dir)208 static int ssi_set_sysclk(struct snd_soc_dai *cpu_dai, int clk_id,
209 unsigned int freq, int dir)
210 {
211 struct ssi_priv *ssi = &ssi_cpu_data[cpu_dai->id];
212
213 ssi->sysclk = freq;
214
215 return 0;
216 }
217
218 /*
219 * This divider is used to generate the SSI_SCK (I2S bitclock) from the
220 * clock at the HAC_BIT_CLK ("oversampling clock") pin.
221 */
ssi_set_clkdiv(struct snd_soc_dai * dai,int did,int div)222 static int ssi_set_clkdiv(struct snd_soc_dai *dai, int did, int div)
223 {
224 struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
225 unsigned long ssicr;
226 int i;
227
228 i = 0;
229 ssicr = SSIREG(SSICR) & ~CR_CKDIV_MASK;
230 switch (div) {
231 case 16: ++i;
232 case 8: ++i;
233 case 4: ++i;
234 case 2: ++i;
235 SSIREG(SSICR) = ssicr | (i << CR_CKDIV_SHIFT);
236 case 1: break;
237 default:
238 pr_debug("ssi: invalid sck divider %d\n", div);
239 return -EINVAL;
240 }
241
242 return 0;
243 }
244
ssi_set_fmt(struct snd_soc_dai * dai,unsigned int fmt)245 static int ssi_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
246 {
247 struct ssi_priv *ssi = &ssi_cpu_data[dai->id];
248 unsigned long ssicr = SSIREG(SSICR);
249
250 pr_debug("ssi_set_fmt()\nssicr was 0x%08lx\n", ssicr);
251
252 ssicr &= ~(CR_DEL | CR_PDTA | CR_BREN | CR_SWSP | CR_SCKP |
253 CR_SWS_MASTER | CR_SCK_MASTER);
254
255 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
256 case SND_SOC_DAIFMT_I2S:
257 break;
258 case SND_SOC_DAIFMT_RIGHT_J:
259 ssicr |= CR_DEL | CR_PDTA;
260 break;
261 case SND_SOC_DAIFMT_LEFT_J:
262 ssicr |= CR_DEL;
263 break;
264 default:
265 pr_debug("ssi: unsupported format\n");
266 return -EINVAL;
267 }
268
269 switch (fmt & SND_SOC_DAIFMT_CLOCK_MASK) {
270 case SND_SOC_DAIFMT_CONT:
271 break;
272 case SND_SOC_DAIFMT_GATED:
273 ssicr |= CR_BREN;
274 break;
275 }
276
277 switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
278 case SND_SOC_DAIFMT_NB_NF:
279 ssicr |= CR_SCKP; /* sample data at low clkedge */
280 break;
281 case SND_SOC_DAIFMT_NB_IF:
282 ssicr |= CR_SCKP | CR_SWSP;
283 break;
284 case SND_SOC_DAIFMT_IB_NF:
285 break;
286 case SND_SOC_DAIFMT_IB_IF:
287 ssicr |= CR_SWSP; /* word select starts low */
288 break;
289 default:
290 pr_debug("ssi: invalid inversion\n");
291 return -EINVAL;
292 }
293
294 switch (fmt & SND_SOC_DAIFMT_CLOCK_PROVIDER_MASK) {
295 case SND_SOC_DAIFMT_BC_FC:
296 break;
297 case SND_SOC_DAIFMT_BP_FC:
298 ssicr |= CR_SCK_MASTER;
299 break;
300 case SND_SOC_DAIFMT_BC_FP:
301 ssicr |= CR_SWS_MASTER;
302 break;
303 case SND_SOC_DAIFMT_BP_FP:
304 ssicr |= CR_SWS_MASTER | CR_SCK_MASTER;
305 break;
306 default:
307 pr_debug("ssi: invalid master/secondary configuration\n");
308 return -EINVAL;
309 }
310
311 SSIREG(SSICR) = ssicr;
312 pr_debug("ssi_set_fmt() leave\nssicr is now 0x%08lx\n", ssicr);
313
314 return 0;
315 }
316
317 /* the SSI depends on an external clocksource (at HAC_BIT_CLK) even in
318 * Master mode, so really this is board specific; the SSI can do any
319 * rate with the right bitclk and divider settings.
320 */
321 #define SSI_RATES \
322 SNDRV_PCM_RATE_8000_192000
323
324 /* the SSI can do 8-32 bit samples, with 8 possible channels */
325 #define SSI_FMTS \
326 (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_U8 | \
327 SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_U16_LE | \
328 SNDRV_PCM_FMTBIT_S20_3LE | SNDRV_PCM_FMTBIT_U20_3LE | \
329 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_U24_3LE | \
330 SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_U32_LE)
331
332 static const struct snd_soc_dai_ops ssi_dai_ops = {
333 .startup = ssi_startup,
334 .shutdown = ssi_shutdown,
335 .trigger = ssi_trigger,
336 .hw_params = ssi_hw_params,
337 .set_sysclk = ssi_set_sysclk,
338 .set_clkdiv = ssi_set_clkdiv,
339 .set_fmt = ssi_set_fmt,
340 };
341
342 static struct snd_soc_dai_driver sh4_ssi_dai[] = {
343 {
344 .name = "ssi-dai.0",
345 .playback = {
346 .rates = SSI_RATES,
347 .formats = SSI_FMTS,
348 .channels_min = 2,
349 .channels_max = 8,
350 },
351 .capture = {
352 .rates = SSI_RATES,
353 .formats = SSI_FMTS,
354 .channels_min = 2,
355 .channels_max = 8,
356 },
357 .ops = &ssi_dai_ops,
358 },
359 #ifdef CONFIG_CPU_SUBTYPE_SH7760
360 {
361 .name = "ssi-dai.1",
362 .playback = {
363 .rates = SSI_RATES,
364 .formats = SSI_FMTS,
365 .channels_min = 2,
366 .channels_max = 8,
367 },
368 .capture = {
369 .rates = SSI_RATES,
370 .formats = SSI_FMTS,
371 .channels_min = 2,
372 .channels_max = 8,
373 },
374 .ops = &ssi_dai_ops,
375 },
376 #endif
377 };
378
379 static const struct snd_soc_component_driver sh4_ssi_component = {
380 .name = "sh4-ssi",
381 .legacy_dai_naming = 1,
382 };
383
sh4_soc_dai_probe(struct platform_device * pdev)384 static int sh4_soc_dai_probe(struct platform_device *pdev)
385 {
386 return devm_snd_soc_register_component(&pdev->dev, &sh4_ssi_component,
387 sh4_ssi_dai,
388 ARRAY_SIZE(sh4_ssi_dai));
389 }
390
391 static struct platform_driver sh4_ssi_driver = {
392 .driver = {
393 .name = "sh4-ssi-dai",
394 },
395
396 .probe = sh4_soc_dai_probe,
397 };
398
399 module_platform_driver(sh4_ssi_driver);
400
401 MODULE_LICENSE("GPL v2");
402 MODULE_DESCRIPTION("SuperH onchip SSI (I2S) audio driver");
403 MODULE_AUTHOR("Manuel Lauss <mano@roarinelk.homelinux.net>");
404