1 /* 2 * Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver 3 * 4 * Author: Timur Tabi <timur@freescale.com> 5 * 6 * Copyright 2007-2010 Freescale Semiconductor, Inc. 7 * 8 * This file is licensed under the terms of the GNU General Public License 9 * version 2. This program is licensed "as is" without any warranty of any 10 * kind, whether express or implied. 11 * 12 * 13 * Some notes why imx-pcm-fiq is used instead of DMA on some boards: 14 * 15 * The i.MX SSI core has some nasty limitations in AC97 mode. While most 16 * sane processor vendors have a FIFO per AC97 slot, the i.MX has only 17 * one FIFO which combines all valid receive slots. We cannot even select 18 * which slots we want to receive. The WM9712 with which this driver 19 * was developed with always sends GPIO status data in slot 12 which 20 * we receive in our (PCM-) data stream. The only chance we have is to 21 * manually skip this data in the FIQ handler. With sampling rates different 22 * from 48000Hz not every frame has valid receive data, so the ratio 23 * between pcm data and GPIO status data changes. Our FIQ handler is not 24 * able to handle this, hence this driver only works with 48000Hz sampling 25 * rate. 26 * Reading and writing AC97 registers is another challenge. The core 27 * provides us status bits when the read register is updated with *another* 28 * value. When we read the same register two times (and the register still 29 * contains the same value) these status bits are not set. We work 30 * around this by not polling these bits but only wait a fixed delay. 31 */ 32 33 #include <linux/init.h> 34 #include <linux/io.h> 35 #include <linux/module.h> 36 #include <linux/interrupt.h> 37 #include <linux/clk.h> 38 #include <linux/device.h> 39 #include <linux/delay.h> 40 #include <linux/slab.h> 41 #include <linux/of_address.h> 42 #include <linux/of_irq.h> 43 #include <linux/of_platform.h> 44 45 #include <sound/core.h> 46 #include <sound/pcm.h> 47 #include <sound/pcm_params.h> 48 #include <sound/initval.h> 49 #include <sound/soc.h> 50 #include <sound/dmaengine_pcm.h> 51 52 #include "fsl_ssi.h" 53 #include "imx-pcm.h" 54 55 #ifdef PPC 56 #define read_ssi(addr) in_be32(addr) 57 #define write_ssi(val, addr) out_be32(addr, val) 58 #define write_ssi_mask(addr, clear, set) clrsetbits_be32(addr, clear, set) 59 #else 60 #define read_ssi(addr) readl(addr) 61 #define write_ssi(val, addr) writel(val, addr) 62 /* 63 * FIXME: Proper locking should be added at write_ssi_mask caller level 64 * to ensure this register read/modify/write sequence is race free. 65 */ 66 static inline void write_ssi_mask(u32 __iomem *addr, u32 clear, u32 set) 67 { 68 u32 val = readl(addr); 69 val = (val & ~clear) | set; 70 writel(val, addr); 71 } 72 #endif 73 74 /** 75 * FSLSSI_I2S_RATES: sample rates supported by the I2S 76 * 77 * This driver currently only supports the SSI running in I2S slave mode, 78 * which means the codec determines the sample rate. Therefore, we tell 79 * ALSA that we support all rates and let the codec driver decide what rates 80 * are really supported. 81 */ 82 #define FSLSSI_I2S_RATES (SNDRV_PCM_RATE_5512 | SNDRV_PCM_RATE_8000_192000 | \ 83 SNDRV_PCM_RATE_CONTINUOUS) 84 85 /** 86 * FSLSSI_I2S_FORMATS: audio formats supported by the SSI 87 * 88 * This driver currently only supports the SSI running in I2S slave mode. 89 * 90 * The SSI has a limitation in that the samples must be in the same byte 91 * order as the host CPU. This is because when multiple bytes are written 92 * to the STX register, the bytes and bits must be written in the same 93 * order. The STX is a shift register, so all the bits need to be aligned 94 * (bit-endianness must match byte-endianness). Processors typically write 95 * the bits within a byte in the same order that the bytes of a word are 96 * written in. So if the host CPU is big-endian, then only big-endian 97 * samples will be written to STX properly. 98 */ 99 #ifdef __BIG_ENDIAN 100 #define FSLSSI_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_BE | \ 101 SNDRV_PCM_FMTBIT_S18_3BE | SNDRV_PCM_FMTBIT_S20_3BE | \ 102 SNDRV_PCM_FMTBIT_S24_3BE | SNDRV_PCM_FMTBIT_S24_BE) 103 #else 104 #define FSLSSI_I2S_FORMATS (SNDRV_PCM_FMTBIT_S8 | SNDRV_PCM_FMTBIT_S16_LE | \ 105 SNDRV_PCM_FMTBIT_S18_3LE | SNDRV_PCM_FMTBIT_S20_3LE | \ 106 SNDRV_PCM_FMTBIT_S24_3LE | SNDRV_PCM_FMTBIT_S24_LE) 107 #endif 108 109 /* SIER bitflag of interrupts to enable */ 110 #define SIER_FLAGS (CCSR_SSI_SIER_TFRC_EN | CCSR_SSI_SIER_TDMAE | \ 111 CCSR_SSI_SIER_TIE | CCSR_SSI_SIER_TUE0_EN | \ 112 CCSR_SSI_SIER_TUE1_EN | CCSR_SSI_SIER_RFRC_EN | \ 113 CCSR_SSI_SIER_RDMAE | CCSR_SSI_SIER_RIE | \ 114 CCSR_SSI_SIER_ROE0_EN | CCSR_SSI_SIER_ROE1_EN) 115 116 /** 117 * fsl_ssi_private: per-SSI private data 118 * 119 * @ssi: pointer to the SSI's registers 120 * @ssi_phys: physical address of the SSI registers 121 * @irq: IRQ of this SSI 122 * @first_stream: pointer to the stream that was opened first 123 * @second_stream: pointer to second stream 124 * @playback: the number of playback streams opened 125 * @capture: the number of capture streams opened 126 * @cpu_dai: the CPU DAI for this device 127 * @dev_attr: the sysfs device attribute structure 128 * @stats: SSI statistics 129 * @name: name for this device 130 */ 131 struct fsl_ssi_private { 132 struct ccsr_ssi __iomem *ssi; 133 dma_addr_t ssi_phys; 134 unsigned int irq; 135 struct snd_pcm_substream *first_stream; 136 struct snd_pcm_substream *second_stream; 137 unsigned int fifo_depth; 138 struct snd_soc_dai_driver cpu_dai_drv; 139 struct device_attribute dev_attr; 140 struct platform_device *pdev; 141 142 bool new_binding; 143 bool ssi_on_imx; 144 bool imx_ac97; 145 bool use_dma; 146 struct clk *clk; 147 struct snd_dmaengine_dai_dma_data dma_params_tx; 148 struct snd_dmaengine_dai_dma_data dma_params_rx; 149 struct imx_dma_data filter_data_tx; 150 struct imx_dma_data filter_data_rx; 151 struct imx_pcm_fiq_params fiq_params; 152 153 struct { 154 unsigned int rfrc; 155 unsigned int tfrc; 156 unsigned int cmdau; 157 unsigned int cmddu; 158 unsigned int rxt; 159 unsigned int rdr1; 160 unsigned int rdr0; 161 unsigned int tde1; 162 unsigned int tde0; 163 unsigned int roe1; 164 unsigned int roe0; 165 unsigned int tue1; 166 unsigned int tue0; 167 unsigned int tfs; 168 unsigned int rfs; 169 unsigned int tls; 170 unsigned int rls; 171 unsigned int rff1; 172 unsigned int rff0; 173 unsigned int tfe1; 174 unsigned int tfe0; 175 } stats; 176 177 char name[1]; 178 }; 179 180 /** 181 * fsl_ssi_isr: SSI interrupt handler 182 * 183 * Although it's possible to use the interrupt handler to send and receive 184 * data to/from the SSI, we use the DMA instead. Programming is more 185 * complicated, but the performance is much better. 186 * 187 * This interrupt handler is used only to gather statistics. 188 * 189 * @irq: IRQ of the SSI device 190 * @dev_id: pointer to the ssi_private structure for this SSI device 191 */ 192 static irqreturn_t fsl_ssi_isr(int irq, void *dev_id) 193 { 194 struct fsl_ssi_private *ssi_private = dev_id; 195 struct ccsr_ssi __iomem *ssi = ssi_private->ssi; 196 irqreturn_t ret = IRQ_NONE; 197 __be32 sisr; 198 __be32 sisr2 = 0; 199 200 /* We got an interrupt, so read the status register to see what we 201 were interrupted for. We mask it with the Interrupt Enable register 202 so that we only check for events that we're interested in. 203 */ 204 sisr = read_ssi(&ssi->sisr) & SIER_FLAGS; 205 206 if (sisr & CCSR_SSI_SISR_RFRC) { 207 ssi_private->stats.rfrc++; 208 sisr2 |= CCSR_SSI_SISR_RFRC; 209 ret = IRQ_HANDLED; 210 } 211 212 if (sisr & CCSR_SSI_SISR_TFRC) { 213 ssi_private->stats.tfrc++; 214 sisr2 |= CCSR_SSI_SISR_TFRC; 215 ret = IRQ_HANDLED; 216 } 217 218 if (sisr & CCSR_SSI_SISR_CMDAU) { 219 ssi_private->stats.cmdau++; 220 ret = IRQ_HANDLED; 221 } 222 223 if (sisr & CCSR_SSI_SISR_CMDDU) { 224 ssi_private->stats.cmddu++; 225 ret = IRQ_HANDLED; 226 } 227 228 if (sisr & CCSR_SSI_SISR_RXT) { 229 ssi_private->stats.rxt++; 230 ret = IRQ_HANDLED; 231 } 232 233 if (sisr & CCSR_SSI_SISR_RDR1) { 234 ssi_private->stats.rdr1++; 235 ret = IRQ_HANDLED; 236 } 237 238 if (sisr & CCSR_SSI_SISR_RDR0) { 239 ssi_private->stats.rdr0++; 240 ret = IRQ_HANDLED; 241 } 242 243 if (sisr & CCSR_SSI_SISR_TDE1) { 244 ssi_private->stats.tde1++; 245 ret = IRQ_HANDLED; 246 } 247 248 if (sisr & CCSR_SSI_SISR_TDE0) { 249 ssi_private->stats.tde0++; 250 ret = IRQ_HANDLED; 251 } 252 253 if (sisr & CCSR_SSI_SISR_ROE1) { 254 ssi_private->stats.roe1++; 255 sisr2 |= CCSR_SSI_SISR_ROE1; 256 ret = IRQ_HANDLED; 257 } 258 259 if (sisr & CCSR_SSI_SISR_ROE0) { 260 ssi_private->stats.roe0++; 261 sisr2 |= CCSR_SSI_SISR_ROE0; 262 ret = IRQ_HANDLED; 263 } 264 265 if (sisr & CCSR_SSI_SISR_TUE1) { 266 ssi_private->stats.tue1++; 267 sisr2 |= CCSR_SSI_SISR_TUE1; 268 ret = IRQ_HANDLED; 269 } 270 271 if (sisr & CCSR_SSI_SISR_TUE0) { 272 ssi_private->stats.tue0++; 273 sisr2 |= CCSR_SSI_SISR_TUE0; 274 ret = IRQ_HANDLED; 275 } 276 277 if (sisr & CCSR_SSI_SISR_TFS) { 278 ssi_private->stats.tfs++; 279 ret = IRQ_HANDLED; 280 } 281 282 if (sisr & CCSR_SSI_SISR_RFS) { 283 ssi_private->stats.rfs++; 284 ret = IRQ_HANDLED; 285 } 286 287 if (sisr & CCSR_SSI_SISR_TLS) { 288 ssi_private->stats.tls++; 289 ret = IRQ_HANDLED; 290 } 291 292 if (sisr & CCSR_SSI_SISR_RLS) { 293 ssi_private->stats.rls++; 294 ret = IRQ_HANDLED; 295 } 296 297 if (sisr & CCSR_SSI_SISR_RFF1) { 298 ssi_private->stats.rff1++; 299 ret = IRQ_HANDLED; 300 } 301 302 if (sisr & CCSR_SSI_SISR_RFF0) { 303 ssi_private->stats.rff0++; 304 ret = IRQ_HANDLED; 305 } 306 307 if (sisr & CCSR_SSI_SISR_TFE1) { 308 ssi_private->stats.tfe1++; 309 ret = IRQ_HANDLED; 310 } 311 312 if (sisr & CCSR_SSI_SISR_TFE0) { 313 ssi_private->stats.tfe0++; 314 ret = IRQ_HANDLED; 315 } 316 317 /* Clear the bits that we set */ 318 if (sisr2) 319 write_ssi(sisr2, &ssi->sisr); 320 321 return ret; 322 } 323 324 static int fsl_ssi_setup(struct fsl_ssi_private *ssi_private) 325 { 326 struct ccsr_ssi __iomem *ssi = ssi_private->ssi; 327 u8 i2s_mode; 328 u8 wm; 329 int synchronous = ssi_private->cpu_dai_drv.symmetric_rates; 330 331 if (ssi_private->imx_ac97) 332 i2s_mode = CCSR_SSI_SCR_I2S_MODE_NORMAL | CCSR_SSI_SCR_NET; 333 else 334 i2s_mode = CCSR_SSI_SCR_I2S_MODE_SLAVE; 335 336 /* 337 * Section 16.5 of the MPC8610 reference manual says that the SSI needs 338 * to be disabled before updating the registers we set here. 339 */ 340 write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0); 341 342 /* 343 * Program the SSI into I2S Slave Non-Network Synchronous mode. Also 344 * enable the transmit and receive FIFO. 345 * 346 * FIXME: Little-endian samples require a different shift dir 347 */ 348 write_ssi_mask(&ssi->scr, 349 CCSR_SSI_SCR_I2S_MODE_MASK | CCSR_SSI_SCR_SYN, 350 CCSR_SSI_SCR_TFR_CLK_DIS | 351 i2s_mode | 352 (synchronous ? CCSR_SSI_SCR_SYN : 0)); 353 354 write_ssi(CCSR_SSI_STCR_TXBIT0 | CCSR_SSI_STCR_TFEN0 | 355 CCSR_SSI_STCR_TFSI | CCSR_SSI_STCR_TEFS | 356 CCSR_SSI_STCR_TSCKP, &ssi->stcr); 357 358 write_ssi(CCSR_SSI_SRCR_RXBIT0 | CCSR_SSI_SRCR_RFEN0 | 359 CCSR_SSI_SRCR_RFSI | CCSR_SSI_SRCR_REFS | 360 CCSR_SSI_SRCR_RSCKP, &ssi->srcr); 361 /* 362 * The DC and PM bits are only used if the SSI is the clock master. 363 */ 364 365 /* 366 * Set the watermark for transmit FIFI 0 and receive FIFO 0. We don't 367 * use FIFO 1. We program the transmit water to signal a DMA transfer 368 * if there are only two (or fewer) elements left in the FIFO. Two 369 * elements equals one frame (left channel, right channel). This value, 370 * however, depends on the depth of the transmit buffer. 371 * 372 * We set the watermark on the same level as the DMA burstsize. For 373 * fiq it is probably better to use the biggest possible watermark 374 * size. 375 */ 376 if (ssi_private->use_dma) 377 wm = ssi_private->fifo_depth - 2; 378 else 379 wm = ssi_private->fifo_depth; 380 381 write_ssi(CCSR_SSI_SFCSR_TFWM0(wm) | CCSR_SSI_SFCSR_RFWM0(wm) | 382 CCSR_SSI_SFCSR_TFWM1(wm) | CCSR_SSI_SFCSR_RFWM1(wm), 383 &ssi->sfcsr); 384 385 /* 386 * For ac97 interrupts are enabled with the startup of the substream 387 * because it is also running without an active substream. Normally SSI 388 * is only enabled when there is a substream. 389 */ 390 if (ssi_private->imx_ac97) { 391 /* 392 * Setup the clock control register 393 */ 394 write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13), 395 &ssi->stccr); 396 write_ssi(CCSR_SSI_SxCCR_WL(17) | CCSR_SSI_SxCCR_DC(13), 397 &ssi->srccr); 398 399 /* 400 * Enable AC97 mode and startup the SSI 401 */ 402 write_ssi(CCSR_SSI_SACNT_AC97EN | CCSR_SSI_SACNT_FV, 403 &ssi->sacnt); 404 write_ssi(0xff, &ssi->saccdis); 405 write_ssi(0x300, &ssi->saccen); 406 407 /* 408 * Enable SSI, Transmit and Receive 409 */ 410 write_ssi_mask(&ssi->scr, 0, CCSR_SSI_SCR_SSIEN | 411 CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE); 412 413 write_ssi(CCSR_SSI_SOR_WAIT(3), &ssi->sor); 414 } 415 416 return 0; 417 } 418 419 420 /** 421 * fsl_ssi_startup: create a new substream 422 * 423 * This is the first function called when a stream is opened. 424 * 425 * If this is the first stream open, then grab the IRQ and program most of 426 * the SSI registers. 427 */ 428 static int fsl_ssi_startup(struct snd_pcm_substream *substream, 429 struct snd_soc_dai *dai) 430 { 431 struct snd_soc_pcm_runtime *rtd = substream->private_data; 432 struct fsl_ssi_private *ssi_private = 433 snd_soc_dai_get_drvdata(rtd->cpu_dai); 434 int synchronous = ssi_private->cpu_dai_drv.symmetric_rates; 435 436 /* 437 * If this is the first stream opened, then request the IRQ 438 * and initialize the SSI registers. 439 */ 440 if (!ssi_private->first_stream) { 441 ssi_private->first_stream = substream; 442 443 /* 444 * fsl_ssi_setup was already called by ac97_init earlier if 445 * the driver is in ac97 mode. 446 */ 447 if (!ssi_private->imx_ac97) 448 fsl_ssi_setup(ssi_private); 449 } else { 450 if (synchronous) { 451 struct snd_pcm_runtime *first_runtime = 452 ssi_private->first_stream->runtime; 453 /* 454 * This is the second stream open, and we're in 455 * synchronous mode, so we need to impose sample 456 * sample size constraints. This is because STCCR is 457 * used for playback and capture in synchronous mode, 458 * so there's no way to specify different word 459 * lengths. 460 * 461 * Note that this can cause a race condition if the 462 * second stream is opened before the first stream is 463 * fully initialized. We provide some protection by 464 * checking to make sure the first stream is 465 * initialized, but it's not perfect. ALSA sometimes 466 * re-initializes the driver with a different sample 467 * rate or size. If the second stream is opened 468 * before the first stream has received its final 469 * parameters, then the second stream may be 470 * constrained to the wrong sample rate or size. 471 */ 472 if (!first_runtime->sample_bits) { 473 dev_err(substream->pcm->card->dev, 474 "set sample size in %s stream first\n", 475 substream->stream == 476 SNDRV_PCM_STREAM_PLAYBACK 477 ? "capture" : "playback"); 478 return -EAGAIN; 479 } 480 481 snd_pcm_hw_constraint_minmax(substream->runtime, 482 SNDRV_PCM_HW_PARAM_SAMPLE_BITS, 483 first_runtime->sample_bits, 484 first_runtime->sample_bits); 485 } 486 487 ssi_private->second_stream = substream; 488 } 489 490 return 0; 491 } 492 493 /** 494 * fsl_ssi_hw_params - program the sample size 495 * 496 * Most of the SSI registers have been programmed in the startup function, 497 * but the word length must be programmed here. Unfortunately, programming 498 * the SxCCR.WL bits requires the SSI to be temporarily disabled. This can 499 * cause a problem with supporting simultaneous playback and capture. If 500 * the SSI is already playing a stream, then that stream may be temporarily 501 * stopped when you start capture. 502 * 503 * Note: The SxCCR.DC and SxCCR.PM bits are only used if the SSI is the 504 * clock master. 505 */ 506 static int fsl_ssi_hw_params(struct snd_pcm_substream *substream, 507 struct snd_pcm_hw_params *hw_params, struct snd_soc_dai *cpu_dai) 508 { 509 struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(cpu_dai); 510 struct ccsr_ssi __iomem *ssi = ssi_private->ssi; 511 unsigned int sample_size = 512 snd_pcm_format_width(params_format(hw_params)); 513 u32 wl = CCSR_SSI_SxCCR_WL(sample_size); 514 int enabled = read_ssi(&ssi->scr) & CCSR_SSI_SCR_SSIEN; 515 516 /* 517 * If we're in synchronous mode, and the SSI is already enabled, 518 * then STCCR is already set properly. 519 */ 520 if (enabled && ssi_private->cpu_dai_drv.symmetric_rates) 521 return 0; 522 523 /* 524 * FIXME: The documentation says that SxCCR[WL] should not be 525 * modified while the SSI is enabled. The only time this can 526 * happen is if we're trying to do simultaneous playback and 527 * capture in asynchronous mode. Unfortunately, I have been enable 528 * to get that to work at all on the P1022DS. Therefore, we don't 529 * bother to disable/enable the SSI when setting SxCCR[WL], because 530 * the SSI will stop anyway. Maybe one day, this will get fixed. 531 */ 532 533 /* In synchronous mode, the SSI uses STCCR for capture */ 534 if ((substream->stream == SNDRV_PCM_STREAM_PLAYBACK) || 535 ssi_private->cpu_dai_drv.symmetric_rates) 536 write_ssi_mask(&ssi->stccr, CCSR_SSI_SxCCR_WL_MASK, wl); 537 else 538 write_ssi_mask(&ssi->srccr, CCSR_SSI_SxCCR_WL_MASK, wl); 539 540 return 0; 541 } 542 543 /** 544 * fsl_ssi_trigger: start and stop the DMA transfer. 545 * 546 * This function is called by ALSA to start, stop, pause, and resume the DMA 547 * transfer of data. 548 * 549 * The DMA channel is in external master start and pause mode, which 550 * means the SSI completely controls the flow of data. 551 */ 552 static int fsl_ssi_trigger(struct snd_pcm_substream *substream, int cmd, 553 struct snd_soc_dai *dai) 554 { 555 struct snd_soc_pcm_runtime *rtd = substream->private_data; 556 struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai); 557 struct ccsr_ssi __iomem *ssi = ssi_private->ssi; 558 unsigned int sier_bits; 559 560 /* 561 * Enable only the interrupts and DMA requests 562 * that are needed for the channel. As the fiq 563 * is polling for this bits, we have to ensure 564 * that this are aligned with the preallocated 565 * buffers 566 */ 567 568 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) { 569 if (ssi_private->use_dma) 570 sier_bits = SIER_FLAGS; 571 else 572 sier_bits = CCSR_SSI_SIER_TIE | CCSR_SSI_SIER_TFE0_EN; 573 } else { 574 if (ssi_private->use_dma) 575 sier_bits = SIER_FLAGS; 576 else 577 sier_bits = CCSR_SSI_SIER_RIE | CCSR_SSI_SIER_RFF0_EN; 578 } 579 580 switch (cmd) { 581 case SNDRV_PCM_TRIGGER_START: 582 case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: 583 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) 584 write_ssi_mask(&ssi->scr, 0, 585 CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_TE); 586 else 587 write_ssi_mask(&ssi->scr, 0, 588 CCSR_SSI_SCR_SSIEN | CCSR_SSI_SCR_RE); 589 break; 590 591 case SNDRV_PCM_TRIGGER_STOP: 592 case SNDRV_PCM_TRIGGER_PAUSE_PUSH: 593 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) 594 write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_TE, 0); 595 else 596 write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_RE, 0); 597 598 if (!ssi_private->imx_ac97 && (read_ssi(&ssi->scr) & 599 (CCSR_SSI_SCR_TE | CCSR_SSI_SCR_RE)) == 0) 600 write_ssi_mask(&ssi->scr, CCSR_SSI_SCR_SSIEN, 0); 601 break; 602 603 default: 604 return -EINVAL; 605 } 606 607 write_ssi(sier_bits, &ssi->sier); 608 609 return 0; 610 } 611 612 /** 613 * fsl_ssi_shutdown: shutdown the SSI 614 * 615 * Shutdown the SSI if there are no other substreams open. 616 */ 617 static void fsl_ssi_shutdown(struct snd_pcm_substream *substream, 618 struct snd_soc_dai *dai) 619 { 620 struct snd_soc_pcm_runtime *rtd = substream->private_data; 621 struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(rtd->cpu_dai); 622 623 if (ssi_private->first_stream == substream) 624 ssi_private->first_stream = ssi_private->second_stream; 625 626 ssi_private->second_stream = NULL; 627 } 628 629 static int fsl_ssi_dai_probe(struct snd_soc_dai *dai) 630 { 631 struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata(dai); 632 633 if (ssi_private->ssi_on_imx && ssi_private->use_dma) { 634 dai->playback_dma_data = &ssi_private->dma_params_tx; 635 dai->capture_dma_data = &ssi_private->dma_params_rx; 636 } 637 638 return 0; 639 } 640 641 static const struct snd_soc_dai_ops fsl_ssi_dai_ops = { 642 .startup = fsl_ssi_startup, 643 .hw_params = fsl_ssi_hw_params, 644 .shutdown = fsl_ssi_shutdown, 645 .trigger = fsl_ssi_trigger, 646 }; 647 648 /* Template for the CPU dai driver structure */ 649 static struct snd_soc_dai_driver fsl_ssi_dai_template = { 650 .probe = fsl_ssi_dai_probe, 651 .playback = { 652 /* The SSI does not support monaural audio. */ 653 .channels_min = 2, 654 .channels_max = 2, 655 .rates = FSLSSI_I2S_RATES, 656 .formats = FSLSSI_I2S_FORMATS, 657 }, 658 .capture = { 659 .channels_min = 2, 660 .channels_max = 2, 661 .rates = FSLSSI_I2S_RATES, 662 .formats = FSLSSI_I2S_FORMATS, 663 }, 664 .ops = &fsl_ssi_dai_ops, 665 }; 666 667 static const struct snd_soc_component_driver fsl_ssi_component = { 668 .name = "fsl-ssi", 669 }; 670 671 /** 672 * fsl_ssi_ac97_trigger: start and stop the AC97 receive/transmit. 673 * 674 * This function is called by ALSA to start, stop, pause, and resume the 675 * transfer of data. 676 */ 677 static int fsl_ssi_ac97_trigger(struct snd_pcm_substream *substream, int cmd, 678 struct snd_soc_dai *dai) 679 { 680 struct snd_soc_pcm_runtime *rtd = substream->private_data; 681 struct fsl_ssi_private *ssi_private = snd_soc_dai_get_drvdata( 682 rtd->cpu_dai); 683 struct ccsr_ssi __iomem *ssi = ssi_private->ssi; 684 685 switch (cmd) { 686 case SNDRV_PCM_TRIGGER_START: 687 case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: 688 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) 689 write_ssi_mask(&ssi->sier, 0, CCSR_SSI_SIER_TIE | 690 CCSR_SSI_SIER_TFE0_EN); 691 else 692 write_ssi_mask(&ssi->sier, 0, CCSR_SSI_SIER_RIE | 693 CCSR_SSI_SIER_RFF0_EN); 694 break; 695 696 case SNDRV_PCM_TRIGGER_STOP: 697 case SNDRV_PCM_TRIGGER_PAUSE_PUSH: 698 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) 699 write_ssi_mask(&ssi->sier, CCSR_SSI_SIER_TIE | 700 CCSR_SSI_SIER_TFE0_EN, 0); 701 else 702 write_ssi_mask(&ssi->sier, CCSR_SSI_SIER_RIE | 703 CCSR_SSI_SIER_RFF0_EN, 0); 704 break; 705 706 default: 707 return -EINVAL; 708 } 709 710 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK) 711 write_ssi(CCSR_SSI_SOR_TX_CLR, &ssi->sor); 712 else 713 write_ssi(CCSR_SSI_SOR_RX_CLR, &ssi->sor); 714 715 return 0; 716 } 717 718 static const struct snd_soc_dai_ops fsl_ssi_ac97_dai_ops = { 719 .startup = fsl_ssi_startup, 720 .shutdown = fsl_ssi_shutdown, 721 .trigger = fsl_ssi_ac97_trigger, 722 }; 723 724 static struct snd_soc_dai_driver fsl_ssi_ac97_dai = { 725 .ac97_control = 1, 726 .playback = { 727 .stream_name = "AC97 Playback", 728 .channels_min = 2, 729 .channels_max = 2, 730 .rates = SNDRV_PCM_RATE_8000_48000, 731 .formats = SNDRV_PCM_FMTBIT_S16_LE, 732 }, 733 .capture = { 734 .stream_name = "AC97 Capture", 735 .channels_min = 2, 736 .channels_max = 2, 737 .rates = SNDRV_PCM_RATE_48000, 738 .formats = SNDRV_PCM_FMTBIT_S16_LE, 739 }, 740 .ops = &fsl_ssi_ac97_dai_ops, 741 }; 742 743 744 static struct fsl_ssi_private *fsl_ac97_data; 745 746 static void fsl_ssi_ac97_init(void) 747 { 748 fsl_ssi_setup(fsl_ac97_data); 749 } 750 751 void fsl_ssi_ac97_write(struct snd_ac97 *ac97, unsigned short reg, 752 unsigned short val) 753 { 754 struct ccsr_ssi *ssi = fsl_ac97_data->ssi; 755 unsigned int lreg; 756 unsigned int lval; 757 758 if (reg > 0x7f) 759 return; 760 761 762 lreg = reg << 12; 763 write_ssi(lreg, &ssi->sacadd); 764 765 lval = val << 4; 766 write_ssi(lval , &ssi->sacdat); 767 768 write_ssi_mask(&ssi->sacnt, CCSR_SSI_SACNT_RDWR_MASK, 769 CCSR_SSI_SACNT_WR); 770 udelay(100); 771 } 772 773 unsigned short fsl_ssi_ac97_read(struct snd_ac97 *ac97, 774 unsigned short reg) 775 { 776 struct ccsr_ssi *ssi = fsl_ac97_data->ssi; 777 778 unsigned short val = -1; 779 unsigned int lreg; 780 781 lreg = (reg & 0x7f) << 12; 782 write_ssi(lreg, &ssi->sacadd); 783 write_ssi_mask(&ssi->sacnt, CCSR_SSI_SACNT_RDWR_MASK, 784 CCSR_SSI_SACNT_RD); 785 786 udelay(100); 787 788 val = (read_ssi(&ssi->sacdat) >> 4) & 0xffff; 789 790 return val; 791 } 792 793 static struct snd_ac97_bus_ops fsl_ssi_ac97_ops = { 794 .read = fsl_ssi_ac97_read, 795 .write = fsl_ssi_ac97_write, 796 }; 797 798 /* Show the statistics of a flag only if its interrupt is enabled. The 799 * compiler will optimze this code to a no-op if the interrupt is not 800 * enabled. 801 */ 802 #define SIER_SHOW(flag, name) \ 803 do { \ 804 if (SIER_FLAGS & CCSR_SSI_SIER_##flag) \ 805 length += sprintf(buf + length, #name "=%u\n", \ 806 ssi_private->stats.name); \ 807 } while (0) 808 809 810 /** 811 * fsl_sysfs_ssi_show: display SSI statistics 812 * 813 * Display the statistics for the current SSI device. To avoid confusion, 814 * we only show those counts that are enabled. 815 */ 816 static ssize_t fsl_sysfs_ssi_show(struct device *dev, 817 struct device_attribute *attr, char *buf) 818 { 819 struct fsl_ssi_private *ssi_private = 820 container_of(attr, struct fsl_ssi_private, dev_attr); 821 ssize_t length = 0; 822 823 SIER_SHOW(RFRC_EN, rfrc); 824 SIER_SHOW(TFRC_EN, tfrc); 825 SIER_SHOW(CMDAU_EN, cmdau); 826 SIER_SHOW(CMDDU_EN, cmddu); 827 SIER_SHOW(RXT_EN, rxt); 828 SIER_SHOW(RDR1_EN, rdr1); 829 SIER_SHOW(RDR0_EN, rdr0); 830 SIER_SHOW(TDE1_EN, tde1); 831 SIER_SHOW(TDE0_EN, tde0); 832 SIER_SHOW(ROE1_EN, roe1); 833 SIER_SHOW(ROE0_EN, roe0); 834 SIER_SHOW(TUE1_EN, tue1); 835 SIER_SHOW(TUE0_EN, tue0); 836 SIER_SHOW(TFS_EN, tfs); 837 SIER_SHOW(RFS_EN, rfs); 838 SIER_SHOW(TLS_EN, tls); 839 SIER_SHOW(RLS_EN, rls); 840 SIER_SHOW(RFF1_EN, rff1); 841 SIER_SHOW(RFF0_EN, rff0); 842 SIER_SHOW(TFE1_EN, tfe1); 843 SIER_SHOW(TFE0_EN, tfe0); 844 845 return length; 846 } 847 848 /** 849 * Make every character in a string lower-case 850 */ 851 static void make_lowercase(char *s) 852 { 853 char *p = s; 854 char c; 855 856 while ((c = *p)) { 857 if ((c >= 'A') && (c <= 'Z')) 858 *p = c + ('a' - 'A'); 859 p++; 860 } 861 } 862 863 static int fsl_ssi_probe(struct platform_device *pdev) 864 { 865 struct fsl_ssi_private *ssi_private; 866 int ret = 0; 867 struct device_attribute *dev_attr = NULL; 868 struct device_node *np = pdev->dev.of_node; 869 const char *p, *sprop; 870 const uint32_t *iprop; 871 struct resource res; 872 char name[64]; 873 bool shared; 874 bool ac97 = false; 875 876 /* SSIs that are not connected on the board should have a 877 * status = "disabled" 878 * property in their device tree nodes. 879 */ 880 if (!of_device_is_available(np)) 881 return -ENODEV; 882 883 /* We only support the SSI in "I2S Slave" mode */ 884 sprop = of_get_property(np, "fsl,mode", NULL); 885 if (!sprop) { 886 dev_err(&pdev->dev, "fsl,mode property is necessary\n"); 887 return -EINVAL; 888 } 889 if (!strcmp(sprop, "ac97-slave")) { 890 ac97 = true; 891 } else if (strcmp(sprop, "i2s-slave")) { 892 dev_notice(&pdev->dev, "mode %s is unsupported\n", sprop); 893 return -ENODEV; 894 } 895 896 /* The DAI name is the last part of the full name of the node. */ 897 p = strrchr(np->full_name, '/') + 1; 898 ssi_private = devm_kzalloc(&pdev->dev, sizeof(*ssi_private) + strlen(p), 899 GFP_KERNEL); 900 if (!ssi_private) { 901 dev_err(&pdev->dev, "could not allocate DAI object\n"); 902 return -ENOMEM; 903 } 904 905 strcpy(ssi_private->name, p); 906 907 ssi_private->use_dma = !of_property_read_bool(np, 908 "fsl,fiq-stream-filter"); 909 910 if (ac97) { 911 memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_ac97_dai, 912 sizeof(fsl_ssi_ac97_dai)); 913 914 fsl_ac97_data = ssi_private; 915 ssi_private->imx_ac97 = true; 916 917 snd_soc_set_ac97_ops_of_reset(&fsl_ssi_ac97_ops, pdev); 918 } else { 919 /* Initialize this copy of the CPU DAI driver structure */ 920 memcpy(&ssi_private->cpu_dai_drv, &fsl_ssi_dai_template, 921 sizeof(fsl_ssi_dai_template)); 922 } 923 ssi_private->cpu_dai_drv.name = ssi_private->name; 924 925 /* Get the addresses and IRQ */ 926 ret = of_address_to_resource(np, 0, &res); 927 if (ret) { 928 dev_err(&pdev->dev, "could not determine device resources\n"); 929 return ret; 930 } 931 ssi_private->ssi = of_iomap(np, 0); 932 if (!ssi_private->ssi) { 933 dev_err(&pdev->dev, "could not map device resources\n"); 934 return -ENOMEM; 935 } 936 ssi_private->ssi_phys = res.start; 937 938 ssi_private->irq = irq_of_parse_and_map(np, 0); 939 if (ssi_private->irq == 0) { 940 dev_err(&pdev->dev, "no irq for node %s\n", np->full_name); 941 return -ENXIO; 942 } 943 944 /* Are the RX and the TX clocks locked? */ 945 if (!of_find_property(np, "fsl,ssi-asynchronous", NULL)) 946 ssi_private->cpu_dai_drv.symmetric_rates = 1; 947 948 /* Determine the FIFO depth. */ 949 iprop = of_get_property(np, "fsl,fifo-depth", NULL); 950 if (iprop) 951 ssi_private->fifo_depth = be32_to_cpup(iprop); 952 else 953 /* Older 8610 DTs didn't have the fifo-depth property */ 954 ssi_private->fifo_depth = 8; 955 956 if (of_device_is_compatible(pdev->dev.of_node, "fsl,imx21-ssi")) { 957 u32 dma_events[2]; 958 ssi_private->ssi_on_imx = true; 959 960 ssi_private->clk = devm_clk_get(&pdev->dev, NULL); 961 if (IS_ERR(ssi_private->clk)) { 962 ret = PTR_ERR(ssi_private->clk); 963 dev_err(&pdev->dev, "could not get clock: %d\n", ret); 964 goto error_irqmap; 965 } 966 ret = clk_prepare_enable(ssi_private->clk); 967 if (ret) { 968 dev_err(&pdev->dev, "clk_prepare_enable failed: %d\n", 969 ret); 970 goto error_irqmap; 971 } 972 973 /* 974 * We have burstsize be "fifo_depth - 2" to match the SSI 975 * watermark setting in fsl_ssi_startup(). 976 */ 977 ssi_private->dma_params_tx.maxburst = 978 ssi_private->fifo_depth - 2; 979 ssi_private->dma_params_rx.maxburst = 980 ssi_private->fifo_depth - 2; 981 ssi_private->dma_params_tx.addr = 982 ssi_private->ssi_phys + offsetof(struct ccsr_ssi, stx0); 983 ssi_private->dma_params_rx.addr = 984 ssi_private->ssi_phys + offsetof(struct ccsr_ssi, srx0); 985 ssi_private->dma_params_tx.filter_data = 986 &ssi_private->filter_data_tx; 987 ssi_private->dma_params_rx.filter_data = 988 &ssi_private->filter_data_rx; 989 if (!of_property_read_bool(pdev->dev.of_node, "dmas") && 990 ssi_private->use_dma) { 991 /* 992 * FIXME: This is a temporary solution until all 993 * necessary dma drivers support the generic dma 994 * bindings. 995 */ 996 ret = of_property_read_u32_array(pdev->dev.of_node, 997 "fsl,ssi-dma-events", dma_events, 2); 998 if (ret && ssi_private->use_dma) { 999 dev_err(&pdev->dev, "could not get dma events but fsl-ssi is configured to use DMA\n"); 1000 goto error_clk; 1001 } 1002 } 1003 1004 shared = of_device_is_compatible(of_get_parent(np), 1005 "fsl,spba-bus"); 1006 1007 imx_pcm_dma_params_init_data(&ssi_private->filter_data_tx, 1008 dma_events[0], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI); 1009 imx_pcm_dma_params_init_data(&ssi_private->filter_data_rx, 1010 dma_events[1], shared ? IMX_DMATYPE_SSI_SP : IMX_DMATYPE_SSI); 1011 } else if (ssi_private->use_dma) { 1012 /* The 'name' should not have any slashes in it. */ 1013 ret = devm_request_irq(&pdev->dev, ssi_private->irq, 1014 fsl_ssi_isr, 0, ssi_private->name, 1015 ssi_private); 1016 if (ret < 0) { 1017 dev_err(&pdev->dev, "could not claim irq %u\n", 1018 ssi_private->irq); 1019 goto error_irqmap; 1020 } 1021 } 1022 1023 /* Initialize the the device_attribute structure */ 1024 dev_attr = &ssi_private->dev_attr; 1025 sysfs_attr_init(&dev_attr->attr); 1026 dev_attr->attr.name = "statistics"; 1027 dev_attr->attr.mode = S_IRUGO; 1028 dev_attr->show = fsl_sysfs_ssi_show; 1029 1030 ret = device_create_file(&pdev->dev, dev_attr); 1031 if (ret) { 1032 dev_err(&pdev->dev, "could not create sysfs %s file\n", 1033 ssi_private->dev_attr.attr.name); 1034 goto error_clk; 1035 } 1036 1037 /* Register with ASoC */ 1038 dev_set_drvdata(&pdev->dev, ssi_private); 1039 1040 ret = snd_soc_register_component(&pdev->dev, &fsl_ssi_component, 1041 &ssi_private->cpu_dai_drv, 1); 1042 if (ret) { 1043 dev_err(&pdev->dev, "failed to register DAI: %d\n", ret); 1044 goto error_dev; 1045 } 1046 1047 if (ssi_private->ssi_on_imx) { 1048 if (!ssi_private->use_dma) { 1049 1050 /* 1051 * Some boards use an incompatible codec. To get it 1052 * working, we are using imx-fiq-pcm-audio, that 1053 * can handle those codecs. DMA is not possible in this 1054 * situation. 1055 */ 1056 1057 ssi_private->fiq_params.irq = ssi_private->irq; 1058 ssi_private->fiq_params.base = ssi_private->ssi; 1059 ssi_private->fiq_params.dma_params_rx = 1060 &ssi_private->dma_params_rx; 1061 ssi_private->fiq_params.dma_params_tx = 1062 &ssi_private->dma_params_tx; 1063 1064 ret = imx_pcm_fiq_init(pdev, &ssi_private->fiq_params); 1065 if (ret) 1066 goto error_dev; 1067 } else { 1068 ret = imx_pcm_dma_init(pdev); 1069 if (ret) 1070 goto error_dev; 1071 } 1072 } 1073 1074 /* 1075 * If codec-handle property is missing from SSI node, we assume 1076 * that the machine driver uses new binding which does not require 1077 * SSI driver to trigger machine driver's probe. 1078 */ 1079 if (!of_get_property(np, "codec-handle", NULL)) { 1080 ssi_private->new_binding = true; 1081 goto done; 1082 } 1083 1084 /* Trigger the machine driver's probe function. The platform driver 1085 * name of the machine driver is taken from /compatible property of the 1086 * device tree. We also pass the address of the CPU DAI driver 1087 * structure. 1088 */ 1089 sprop = of_get_property(of_find_node_by_path("/"), "compatible", NULL); 1090 /* Sometimes the compatible name has a "fsl," prefix, so we strip it. */ 1091 p = strrchr(sprop, ','); 1092 if (p) 1093 sprop = p + 1; 1094 snprintf(name, sizeof(name), "snd-soc-%s", sprop); 1095 make_lowercase(name); 1096 1097 ssi_private->pdev = 1098 platform_device_register_data(&pdev->dev, name, 0, NULL, 0); 1099 if (IS_ERR(ssi_private->pdev)) { 1100 ret = PTR_ERR(ssi_private->pdev); 1101 dev_err(&pdev->dev, "failed to register platform: %d\n", ret); 1102 goto error_dai; 1103 } 1104 1105 done: 1106 if (ssi_private->imx_ac97) 1107 fsl_ssi_ac97_init(); 1108 1109 return 0; 1110 1111 error_dai: 1112 if (ssi_private->ssi_on_imx) 1113 imx_pcm_dma_exit(pdev); 1114 snd_soc_unregister_component(&pdev->dev); 1115 1116 error_dev: 1117 device_remove_file(&pdev->dev, dev_attr); 1118 1119 error_clk: 1120 if (ssi_private->ssi_on_imx) 1121 clk_disable_unprepare(ssi_private->clk); 1122 1123 error_irqmap: 1124 irq_dispose_mapping(ssi_private->irq); 1125 1126 return ret; 1127 } 1128 1129 static int fsl_ssi_remove(struct platform_device *pdev) 1130 { 1131 struct fsl_ssi_private *ssi_private = dev_get_drvdata(&pdev->dev); 1132 1133 if (!ssi_private->new_binding) 1134 platform_device_unregister(ssi_private->pdev); 1135 if (ssi_private->ssi_on_imx) 1136 imx_pcm_dma_exit(pdev); 1137 snd_soc_unregister_component(&pdev->dev); 1138 dev_set_drvdata(&pdev->dev, NULL); 1139 device_remove_file(&pdev->dev, &ssi_private->dev_attr); 1140 if (ssi_private->ssi_on_imx) 1141 clk_disable_unprepare(ssi_private->clk); 1142 irq_dispose_mapping(ssi_private->irq); 1143 1144 return 0; 1145 } 1146 1147 static const struct of_device_id fsl_ssi_ids[] = { 1148 { .compatible = "fsl,mpc8610-ssi", }, 1149 { .compatible = "fsl,imx21-ssi", }, 1150 {} 1151 }; 1152 MODULE_DEVICE_TABLE(of, fsl_ssi_ids); 1153 1154 static struct platform_driver fsl_ssi_driver = { 1155 .driver = { 1156 .name = "fsl-ssi-dai", 1157 .owner = THIS_MODULE, 1158 .of_match_table = fsl_ssi_ids, 1159 }, 1160 .probe = fsl_ssi_probe, 1161 .remove = fsl_ssi_remove, 1162 }; 1163 1164 module_platform_driver(fsl_ssi_driver); 1165 1166 MODULE_ALIAS("platform:fsl-ssi-dai"); 1167 MODULE_AUTHOR("Timur Tabi <timur@freescale.com>"); 1168 MODULE_DESCRIPTION("Freescale Synchronous Serial Interface (SSI) ASoC Driver"); 1169 MODULE_LICENSE("GPL v2"); 1170