1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * wm8904.c -- WM8904 ALSA SoC Audio driver
4 *
5 * Copyright 2009-12 Wolfson Microelectronics plc
6 *
7 * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
8 */
9
10 #include <linux/clk.h>
11 #include <linux/module.h>
12 #include <linux/init.h>
13 #include <linux/delay.h>
14 #include <linux/pm.h>
15 #include <linux/i2c.h>
16 #include <linux/regmap.h>
17 #include <linux/regulator/consumer.h>
18 #include <linux/slab.h>
19 #include <sound/core.h>
20 #include <sound/pcm.h>
21 #include <sound/pcm_params.h>
22 #include <sound/soc.h>
23 #include <sound/initval.h>
24 #include <sound/tlv.h>
25 #include <sound/wm8904.h>
26
27 #include "wm8904.h"
28
29 enum wm8904_type {
30 WM8904,
31 WM8912,
32 };
33
34 #define WM8904_NUM_DCS_CHANNELS 4
35
36 #define WM8904_NUM_SUPPLIES 5
37 static const char *wm8904_supply_names[WM8904_NUM_SUPPLIES] = {
38 "DCVDD",
39 "DBVDD",
40 "AVDD",
41 "CPVDD",
42 "MICVDD",
43 };
44
45 /* codec private data */
46 struct wm8904_priv {
47 struct regmap *regmap;
48 struct clk *mclk;
49
50 enum wm8904_type devtype;
51
52 struct regulator_bulk_data supplies[WM8904_NUM_SUPPLIES];
53
54 struct wm8904_pdata *pdata;
55
56 int deemph;
57
58 /* Platform provided DRC configuration */
59 const char **drc_texts;
60 int drc_cfg;
61 struct soc_enum drc_enum;
62
63 /* Platform provided ReTune mobile configuration */
64 int num_retune_mobile_texts;
65 const char **retune_mobile_texts;
66 int retune_mobile_cfg;
67 struct soc_enum retune_mobile_enum;
68
69 /* FLL setup */
70 int fll_src;
71 int fll_fref;
72 int fll_fout;
73
74 /* Clocking configuration */
75 unsigned int mclk_rate;
76 int sysclk_src;
77 unsigned int sysclk_rate;
78
79 int tdm_width;
80 int tdm_slots;
81 int bclk;
82 int fs;
83
84 /* DC servo configuration - cached offset values */
85 int dcs_state[WM8904_NUM_DCS_CHANNELS];
86 };
87
88 static const struct reg_default wm8904_reg_defaults[] = {
89 { 4, 0x0018 }, /* R4 - Bias Control 0 */
90 { 5, 0x0000 }, /* R5 - VMID Control 0 */
91 { 6, 0x0000 }, /* R6 - Mic Bias Control 0 */
92 { 7, 0x0000 }, /* R7 - Mic Bias Control 1 */
93 { 8, 0x0001 }, /* R8 - Analogue DAC 0 */
94 { 9, 0x9696 }, /* R9 - mic Filter Control */
95 { 10, 0x0001 }, /* R10 - Analogue ADC 0 */
96 { 12, 0x0000 }, /* R12 - Power Management 0 */
97 { 14, 0x0000 }, /* R14 - Power Management 2 */
98 { 15, 0x0000 }, /* R15 - Power Management 3 */
99 { 18, 0x0000 }, /* R18 - Power Management 6 */
100 { 20, 0x945E }, /* R20 - Clock Rates 0 */
101 { 21, 0x0C05 }, /* R21 - Clock Rates 1 */
102 { 22, 0x0006 }, /* R22 - Clock Rates 2 */
103 { 24, 0x0050 }, /* R24 - Audio Interface 0 */
104 { 25, 0x000A }, /* R25 - Audio Interface 1 */
105 { 26, 0x00E4 }, /* R26 - Audio Interface 2 */
106 { 27, 0x0040 }, /* R27 - Audio Interface 3 */
107 { 30, 0x00C0 }, /* R30 - DAC Digital Volume Left */
108 { 31, 0x00C0 }, /* R31 - DAC Digital Volume Right */
109 { 32, 0x0000 }, /* R32 - DAC Digital 0 */
110 { 33, 0x0008 }, /* R33 - DAC Digital 1 */
111 { 36, 0x00C0 }, /* R36 - ADC Digital Volume Left */
112 { 37, 0x00C0 }, /* R37 - ADC Digital Volume Right */
113 { 38, 0x0010 }, /* R38 - ADC Digital 0 */
114 { 39, 0x0000 }, /* R39 - Digital Microphone 0 */
115 { 40, 0x01AF }, /* R40 - DRC 0 */
116 { 41, 0x3248 }, /* R41 - DRC 1 */
117 { 42, 0x0000 }, /* R42 - DRC 2 */
118 { 43, 0x0000 }, /* R43 - DRC 3 */
119 { 44, 0x0085 }, /* R44 - Analogue Left Input 0 */
120 { 45, 0x0085 }, /* R45 - Analogue Right Input 0 */
121 { 46, 0x0044 }, /* R46 - Analogue Left Input 1 */
122 { 47, 0x0044 }, /* R47 - Analogue Right Input 1 */
123 { 57, 0x002D }, /* R57 - Analogue OUT1 Left */
124 { 58, 0x002D }, /* R58 - Analogue OUT1 Right */
125 { 59, 0x0039 }, /* R59 - Analogue OUT2 Left */
126 { 60, 0x0039 }, /* R60 - Analogue OUT2 Right */
127 { 61, 0x0000 }, /* R61 - Analogue OUT12 ZC */
128 { 67, 0x0000 }, /* R67 - DC Servo 0 */
129 { 69, 0xAAAA }, /* R69 - DC Servo 2 */
130 { 71, 0xAAAA }, /* R71 - DC Servo 4 */
131 { 72, 0xAAAA }, /* R72 - DC Servo 5 */
132 { 90, 0x0000 }, /* R90 - Analogue HP 0 */
133 { 94, 0x0000 }, /* R94 - Analogue Lineout 0 */
134 { 98, 0x0000 }, /* R98 - Charge Pump 0 */
135 { 104, 0x0004 }, /* R104 - Class W 0 */
136 { 108, 0x0000 }, /* R108 - Write Sequencer 0 */
137 { 109, 0x0000 }, /* R109 - Write Sequencer 1 */
138 { 110, 0x0000 }, /* R110 - Write Sequencer 2 */
139 { 111, 0x0000 }, /* R111 - Write Sequencer 3 */
140 { 112, 0x0000 }, /* R112 - Write Sequencer 4 */
141 { 116, 0x0000 }, /* R116 - FLL Control 1 */
142 { 117, 0x0007 }, /* R117 - FLL Control 2 */
143 { 118, 0x0000 }, /* R118 - FLL Control 3 */
144 { 119, 0x2EE0 }, /* R119 - FLL Control 4 */
145 { 120, 0x0004 }, /* R120 - FLL Control 5 */
146 { 121, 0x0014 }, /* R121 - GPIO Control 1 */
147 { 122, 0x0010 }, /* R122 - GPIO Control 2 */
148 { 123, 0x0010 }, /* R123 - GPIO Control 3 */
149 { 124, 0x0000 }, /* R124 - GPIO Control 4 */
150 { 126, 0x0000 }, /* R126 - Digital Pulls */
151 { 128, 0xFFFF }, /* R128 - Interrupt Status Mask */
152 { 129, 0x0000 }, /* R129 - Interrupt Polarity */
153 { 130, 0x0000 }, /* R130 - Interrupt Debounce */
154 { 134, 0x0000 }, /* R134 - EQ1 */
155 { 135, 0x000C }, /* R135 - EQ2 */
156 { 136, 0x000C }, /* R136 - EQ3 */
157 { 137, 0x000C }, /* R137 - EQ4 */
158 { 138, 0x000C }, /* R138 - EQ5 */
159 { 139, 0x000C }, /* R139 - EQ6 */
160 { 140, 0x0FCA }, /* R140 - EQ7 */
161 { 141, 0x0400 }, /* R141 - EQ8 */
162 { 142, 0x00D8 }, /* R142 - EQ9 */
163 { 143, 0x1EB5 }, /* R143 - EQ10 */
164 { 144, 0xF145 }, /* R144 - EQ11 */
165 { 145, 0x0B75 }, /* R145 - EQ12 */
166 { 146, 0x01C5 }, /* R146 - EQ13 */
167 { 147, 0x1C58 }, /* R147 - EQ14 */
168 { 148, 0xF373 }, /* R148 - EQ15 */
169 { 149, 0x0A54 }, /* R149 - EQ16 */
170 { 150, 0x0558 }, /* R150 - EQ17 */
171 { 151, 0x168E }, /* R151 - EQ18 */
172 { 152, 0xF829 }, /* R152 - EQ19 */
173 { 153, 0x07AD }, /* R153 - EQ20 */
174 { 154, 0x1103 }, /* R154 - EQ21 */
175 { 155, 0x0564 }, /* R155 - EQ22 */
176 { 156, 0x0559 }, /* R156 - EQ23 */
177 { 157, 0x4000 }, /* R157 - EQ24 */
178 { 161, 0x0000 }, /* R161 - Control Interface Test 1 */
179 { 204, 0x0000 }, /* R204 - Analogue Output Bias 0 */
180 { 247, 0x0000 }, /* R247 - FLL NCO Test 0 */
181 { 248, 0x0019 }, /* R248 - FLL NCO Test 1 */
182 };
183
wm8904_volatile_register(struct device * dev,unsigned int reg)184 static bool wm8904_volatile_register(struct device *dev, unsigned int reg)
185 {
186 switch (reg) {
187 case WM8904_SW_RESET_AND_ID:
188 case WM8904_REVISION:
189 case WM8904_DC_SERVO_1:
190 case WM8904_DC_SERVO_6:
191 case WM8904_DC_SERVO_7:
192 case WM8904_DC_SERVO_8:
193 case WM8904_DC_SERVO_9:
194 case WM8904_DC_SERVO_READBACK_0:
195 case WM8904_INTERRUPT_STATUS:
196 return true;
197 default:
198 return false;
199 }
200 }
201
wm8904_readable_register(struct device * dev,unsigned int reg)202 static bool wm8904_readable_register(struct device *dev, unsigned int reg)
203 {
204 switch (reg) {
205 case WM8904_SW_RESET_AND_ID:
206 case WM8904_REVISION:
207 case WM8904_BIAS_CONTROL_0:
208 case WM8904_VMID_CONTROL_0:
209 case WM8904_MIC_BIAS_CONTROL_0:
210 case WM8904_MIC_BIAS_CONTROL_1:
211 case WM8904_ANALOGUE_DAC_0:
212 case WM8904_MIC_FILTER_CONTROL:
213 case WM8904_ANALOGUE_ADC_0:
214 case WM8904_POWER_MANAGEMENT_0:
215 case WM8904_POWER_MANAGEMENT_2:
216 case WM8904_POWER_MANAGEMENT_3:
217 case WM8904_POWER_MANAGEMENT_6:
218 case WM8904_CLOCK_RATES_0:
219 case WM8904_CLOCK_RATES_1:
220 case WM8904_CLOCK_RATES_2:
221 case WM8904_AUDIO_INTERFACE_0:
222 case WM8904_AUDIO_INTERFACE_1:
223 case WM8904_AUDIO_INTERFACE_2:
224 case WM8904_AUDIO_INTERFACE_3:
225 case WM8904_DAC_DIGITAL_VOLUME_LEFT:
226 case WM8904_DAC_DIGITAL_VOLUME_RIGHT:
227 case WM8904_DAC_DIGITAL_0:
228 case WM8904_DAC_DIGITAL_1:
229 case WM8904_ADC_DIGITAL_VOLUME_LEFT:
230 case WM8904_ADC_DIGITAL_VOLUME_RIGHT:
231 case WM8904_ADC_DIGITAL_0:
232 case WM8904_DIGITAL_MICROPHONE_0:
233 case WM8904_DRC_0:
234 case WM8904_DRC_1:
235 case WM8904_DRC_2:
236 case WM8904_DRC_3:
237 case WM8904_ANALOGUE_LEFT_INPUT_0:
238 case WM8904_ANALOGUE_RIGHT_INPUT_0:
239 case WM8904_ANALOGUE_LEFT_INPUT_1:
240 case WM8904_ANALOGUE_RIGHT_INPUT_1:
241 case WM8904_ANALOGUE_OUT1_LEFT:
242 case WM8904_ANALOGUE_OUT1_RIGHT:
243 case WM8904_ANALOGUE_OUT2_LEFT:
244 case WM8904_ANALOGUE_OUT2_RIGHT:
245 case WM8904_ANALOGUE_OUT12_ZC:
246 case WM8904_DC_SERVO_0:
247 case WM8904_DC_SERVO_1:
248 case WM8904_DC_SERVO_2:
249 case WM8904_DC_SERVO_4:
250 case WM8904_DC_SERVO_5:
251 case WM8904_DC_SERVO_6:
252 case WM8904_DC_SERVO_7:
253 case WM8904_DC_SERVO_8:
254 case WM8904_DC_SERVO_9:
255 case WM8904_DC_SERVO_READBACK_0:
256 case WM8904_ANALOGUE_HP_0:
257 case WM8904_ANALOGUE_LINEOUT_0:
258 case WM8904_CHARGE_PUMP_0:
259 case WM8904_CLASS_W_0:
260 case WM8904_WRITE_SEQUENCER_0:
261 case WM8904_WRITE_SEQUENCER_1:
262 case WM8904_WRITE_SEQUENCER_2:
263 case WM8904_WRITE_SEQUENCER_3:
264 case WM8904_WRITE_SEQUENCER_4:
265 case WM8904_FLL_CONTROL_1:
266 case WM8904_FLL_CONTROL_2:
267 case WM8904_FLL_CONTROL_3:
268 case WM8904_FLL_CONTROL_4:
269 case WM8904_FLL_CONTROL_5:
270 case WM8904_GPIO_CONTROL_1:
271 case WM8904_GPIO_CONTROL_2:
272 case WM8904_GPIO_CONTROL_3:
273 case WM8904_GPIO_CONTROL_4:
274 case WM8904_DIGITAL_PULLS:
275 case WM8904_INTERRUPT_STATUS:
276 case WM8904_INTERRUPT_STATUS_MASK:
277 case WM8904_INTERRUPT_POLARITY:
278 case WM8904_INTERRUPT_DEBOUNCE:
279 case WM8904_EQ1:
280 case WM8904_EQ2:
281 case WM8904_EQ3:
282 case WM8904_EQ4:
283 case WM8904_EQ5:
284 case WM8904_EQ6:
285 case WM8904_EQ7:
286 case WM8904_EQ8:
287 case WM8904_EQ9:
288 case WM8904_EQ10:
289 case WM8904_EQ11:
290 case WM8904_EQ12:
291 case WM8904_EQ13:
292 case WM8904_EQ14:
293 case WM8904_EQ15:
294 case WM8904_EQ16:
295 case WM8904_EQ17:
296 case WM8904_EQ18:
297 case WM8904_EQ19:
298 case WM8904_EQ20:
299 case WM8904_EQ21:
300 case WM8904_EQ22:
301 case WM8904_EQ23:
302 case WM8904_EQ24:
303 case WM8904_CONTROL_INTERFACE_TEST_1:
304 case WM8904_ADC_TEST_0:
305 case WM8904_ANALOGUE_OUTPUT_BIAS_0:
306 case WM8904_FLL_NCO_TEST_0:
307 case WM8904_FLL_NCO_TEST_1:
308 return true;
309 default:
310 return false;
311 }
312 }
313
wm8904_configure_clocking(struct snd_soc_component * component)314 static int wm8904_configure_clocking(struct snd_soc_component *component)
315 {
316 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
317 unsigned int clock0, clock2, rate;
318
319 /* Gate the clock while we're updating to avoid misclocking */
320 clock2 = snd_soc_component_read(component, WM8904_CLOCK_RATES_2);
321 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_2,
322 WM8904_SYSCLK_SRC, 0);
323
324 /* This should be done on init() for bypass paths */
325 switch (wm8904->sysclk_src) {
326 case WM8904_CLK_MCLK:
327 dev_dbg(component->dev, "Using %dHz MCLK\n", wm8904->mclk_rate);
328
329 clock2 &= ~WM8904_SYSCLK_SRC;
330 rate = wm8904->mclk_rate;
331
332 /* Ensure the FLL is stopped */
333 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
334 WM8904_FLL_OSC_ENA | WM8904_FLL_ENA, 0);
335 break;
336
337 case WM8904_CLK_FLL:
338 dev_dbg(component->dev, "Using %dHz FLL clock\n",
339 wm8904->fll_fout);
340
341 clock2 |= WM8904_SYSCLK_SRC;
342 rate = wm8904->fll_fout;
343 break;
344
345 default:
346 dev_err(component->dev, "System clock not configured\n");
347 return -EINVAL;
348 }
349
350 /* SYSCLK shouldn't be over 13.5MHz */
351 if (rate > 13500000) {
352 clock0 = WM8904_MCLK_DIV;
353 wm8904->sysclk_rate = rate / 2;
354 } else {
355 clock0 = 0;
356 wm8904->sysclk_rate = rate;
357 }
358
359 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_0, WM8904_MCLK_DIV,
360 clock0);
361
362 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_2,
363 WM8904_CLK_SYS_ENA | WM8904_SYSCLK_SRC, clock2);
364
365 dev_dbg(component->dev, "CLK_SYS is %dHz\n", wm8904->sysclk_rate);
366
367 return 0;
368 }
369
wm8904_set_drc(struct snd_soc_component * component)370 static void wm8904_set_drc(struct snd_soc_component *component)
371 {
372 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
373 struct wm8904_pdata *pdata = wm8904->pdata;
374 int save, i;
375
376 /* Save any enables; the configuration should clear them. */
377 save = snd_soc_component_read(component, WM8904_DRC_0);
378
379 for (i = 0; i < WM8904_DRC_REGS; i++)
380 snd_soc_component_update_bits(component, WM8904_DRC_0 + i, 0xffff,
381 pdata->drc_cfgs[wm8904->drc_cfg].regs[i]);
382
383 /* Reenable the DRC */
384 snd_soc_component_update_bits(component, WM8904_DRC_0,
385 WM8904_DRC_ENA | WM8904_DRC_DAC_PATH, save);
386 }
387
wm8904_put_drc_enum(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)388 static int wm8904_put_drc_enum(struct snd_kcontrol *kcontrol,
389 struct snd_ctl_elem_value *ucontrol)
390 {
391 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
392 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
393 struct wm8904_pdata *pdata = wm8904->pdata;
394 int value = ucontrol->value.enumerated.item[0];
395
396 if (value >= pdata->num_drc_cfgs)
397 return -EINVAL;
398
399 wm8904->drc_cfg = value;
400
401 wm8904_set_drc(component);
402
403 return 0;
404 }
405
wm8904_get_drc_enum(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)406 static int wm8904_get_drc_enum(struct snd_kcontrol *kcontrol,
407 struct snd_ctl_elem_value *ucontrol)
408 {
409 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
410 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
411
412 ucontrol->value.enumerated.item[0] = wm8904->drc_cfg;
413
414 return 0;
415 }
416
wm8904_set_retune_mobile(struct snd_soc_component * component)417 static void wm8904_set_retune_mobile(struct snd_soc_component *component)
418 {
419 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
420 struct wm8904_pdata *pdata = wm8904->pdata;
421 int best, best_val, save, i, cfg;
422
423 if (!pdata || !wm8904->num_retune_mobile_texts)
424 return;
425
426 /* Find the version of the currently selected configuration
427 * with the nearest sample rate. */
428 cfg = wm8904->retune_mobile_cfg;
429 best = 0;
430 best_val = INT_MAX;
431 for (i = 0; i < pdata->num_retune_mobile_cfgs; i++) {
432 if (strcmp(pdata->retune_mobile_cfgs[i].name,
433 wm8904->retune_mobile_texts[cfg]) == 0 &&
434 abs(pdata->retune_mobile_cfgs[i].rate
435 - wm8904->fs) < best_val) {
436 best = i;
437 best_val = abs(pdata->retune_mobile_cfgs[i].rate
438 - wm8904->fs);
439 }
440 }
441
442 dev_dbg(component->dev, "ReTune Mobile %s/%dHz for %dHz sample rate\n",
443 pdata->retune_mobile_cfgs[best].name,
444 pdata->retune_mobile_cfgs[best].rate,
445 wm8904->fs);
446
447 /* The EQ will be disabled while reconfiguring it, remember the
448 * current configuration.
449 */
450 save = snd_soc_component_read(component, WM8904_EQ1);
451
452 for (i = 0; i < WM8904_EQ_REGS; i++)
453 snd_soc_component_update_bits(component, WM8904_EQ1 + i, 0xffff,
454 pdata->retune_mobile_cfgs[best].regs[i]);
455
456 snd_soc_component_update_bits(component, WM8904_EQ1, WM8904_EQ_ENA, save);
457 }
458
wm8904_put_retune_mobile_enum(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)459 static int wm8904_put_retune_mobile_enum(struct snd_kcontrol *kcontrol,
460 struct snd_ctl_elem_value *ucontrol)
461 {
462 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
463 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
464 struct wm8904_pdata *pdata = wm8904->pdata;
465 int value = ucontrol->value.enumerated.item[0];
466
467 if (value >= pdata->num_retune_mobile_cfgs)
468 return -EINVAL;
469
470 wm8904->retune_mobile_cfg = value;
471
472 wm8904_set_retune_mobile(component);
473
474 return 0;
475 }
476
wm8904_get_retune_mobile_enum(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)477 static int wm8904_get_retune_mobile_enum(struct snd_kcontrol *kcontrol,
478 struct snd_ctl_elem_value *ucontrol)
479 {
480 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
481 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
482
483 ucontrol->value.enumerated.item[0] = wm8904->retune_mobile_cfg;
484
485 return 0;
486 }
487
488 static int deemph_settings[] = { 0, 32000, 44100, 48000 };
489
wm8904_set_deemph(struct snd_soc_component * component)490 static int wm8904_set_deemph(struct snd_soc_component *component)
491 {
492 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
493 int val, i, best;
494
495 /* If we're using deemphasis select the nearest available sample
496 * rate.
497 */
498 if (wm8904->deemph) {
499 best = 1;
500 for (i = 2; i < ARRAY_SIZE(deemph_settings); i++) {
501 if (abs(deemph_settings[i] - wm8904->fs) <
502 abs(deemph_settings[best] - wm8904->fs))
503 best = i;
504 }
505
506 val = best << WM8904_DEEMPH_SHIFT;
507 } else {
508 val = 0;
509 }
510
511 dev_dbg(component->dev, "Set deemphasis %d\n", val);
512
513 return snd_soc_component_update_bits(component, WM8904_DAC_DIGITAL_1,
514 WM8904_DEEMPH_MASK, val);
515 }
516
wm8904_get_deemph(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)517 static int wm8904_get_deemph(struct snd_kcontrol *kcontrol,
518 struct snd_ctl_elem_value *ucontrol)
519 {
520 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
521 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
522
523 ucontrol->value.integer.value[0] = wm8904->deemph;
524 return 0;
525 }
526
wm8904_put_deemph(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)527 static int wm8904_put_deemph(struct snd_kcontrol *kcontrol,
528 struct snd_ctl_elem_value *ucontrol)
529 {
530 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
531 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
532 unsigned int deemph = ucontrol->value.integer.value[0];
533
534 if (deemph > 1)
535 return -EINVAL;
536
537 wm8904->deemph = deemph;
538
539 return wm8904_set_deemph(component);
540 }
541
542 static const DECLARE_TLV_DB_SCALE(dac_boost_tlv, 0, 600, 0);
543 static const DECLARE_TLV_DB_SCALE(digital_tlv, -7200, 75, 1);
544 static const DECLARE_TLV_DB_SCALE(out_tlv, -5700, 100, 0);
545 static const DECLARE_TLV_DB_SCALE(sidetone_tlv, -3600, 300, 0);
546 static const DECLARE_TLV_DB_SCALE(eq_tlv, -1200, 100, 0);
547
548 static const char *hpf_mode_text[] = {
549 "Hi-fi", "Voice 1", "Voice 2", "Voice 3"
550 };
551
552 static SOC_ENUM_SINGLE_DECL(hpf_mode, WM8904_ADC_DIGITAL_0, 5,
553 hpf_mode_text);
554
wm8904_adc_osr_put(struct snd_kcontrol * kcontrol,struct snd_ctl_elem_value * ucontrol)555 static int wm8904_adc_osr_put(struct snd_kcontrol *kcontrol,
556 struct snd_ctl_elem_value *ucontrol)
557 {
558 struct snd_soc_component *component = snd_soc_kcontrol_component(kcontrol);
559 unsigned int val;
560 int ret;
561
562 ret = snd_soc_put_volsw(kcontrol, ucontrol);
563 if (ret < 0)
564 return ret;
565
566 if (ucontrol->value.integer.value[0])
567 val = 0;
568 else
569 val = WM8904_ADC_128_OSR_TST_MODE | WM8904_ADC_BIASX1P5;
570
571 snd_soc_component_update_bits(component, WM8904_ADC_TEST_0,
572 WM8904_ADC_128_OSR_TST_MODE | WM8904_ADC_BIASX1P5,
573 val);
574
575 return ret;
576 }
577
578 static const struct snd_kcontrol_new wm8904_adc_snd_controls[] = {
579 SOC_DOUBLE_R_TLV("Digital Capture Volume", WM8904_ADC_DIGITAL_VOLUME_LEFT,
580 WM8904_ADC_DIGITAL_VOLUME_RIGHT, 1, 119, 0, digital_tlv),
581
582 /* No TLV since it depends on mode */
583 SOC_DOUBLE_R("Capture Volume", WM8904_ANALOGUE_LEFT_INPUT_0,
584 WM8904_ANALOGUE_RIGHT_INPUT_0, 0, 31, 0),
585 SOC_DOUBLE_R("Capture Switch", WM8904_ANALOGUE_LEFT_INPUT_0,
586 WM8904_ANALOGUE_RIGHT_INPUT_0, 7, 1, 1),
587
588 SOC_SINGLE("High Pass Filter Switch", WM8904_ADC_DIGITAL_0, 4, 1, 0),
589 SOC_ENUM("High Pass Filter Mode", hpf_mode),
590 SOC_SINGLE_EXT("ADC 128x OSR Switch", WM8904_ANALOGUE_ADC_0, 0, 1, 0,
591 snd_soc_get_volsw, wm8904_adc_osr_put),
592 };
593
594 static const char *drc_path_text[] = {
595 "ADC", "DAC"
596 };
597
598 static SOC_ENUM_SINGLE_DECL(drc_path, WM8904_DRC_0, 14, drc_path_text);
599
600 static const struct snd_kcontrol_new wm8904_dac_snd_controls[] = {
601 SOC_SINGLE_TLV("Digital Playback Boost Volume",
602 WM8904_AUDIO_INTERFACE_0, 9, 3, 0, dac_boost_tlv),
603 SOC_DOUBLE_R_TLV("Digital Playback Volume", WM8904_DAC_DIGITAL_VOLUME_LEFT,
604 WM8904_DAC_DIGITAL_VOLUME_RIGHT, 1, 96, 0, digital_tlv),
605
606 SOC_DOUBLE_R_TLV("Headphone Volume", WM8904_ANALOGUE_OUT1_LEFT,
607 WM8904_ANALOGUE_OUT1_RIGHT, 0, 63, 0, out_tlv),
608 SOC_DOUBLE_R("Headphone Switch", WM8904_ANALOGUE_OUT1_LEFT,
609 WM8904_ANALOGUE_OUT1_RIGHT, 8, 1, 1),
610 SOC_DOUBLE_R("Headphone ZC Switch", WM8904_ANALOGUE_OUT1_LEFT,
611 WM8904_ANALOGUE_OUT1_RIGHT, 6, 1, 0),
612
613 SOC_DOUBLE_R_TLV("Line Output Volume", WM8904_ANALOGUE_OUT2_LEFT,
614 WM8904_ANALOGUE_OUT2_RIGHT, 0, 63, 0, out_tlv),
615 SOC_DOUBLE_R("Line Output Switch", WM8904_ANALOGUE_OUT2_LEFT,
616 WM8904_ANALOGUE_OUT2_RIGHT, 8, 1, 1),
617 SOC_DOUBLE_R("Line Output ZC Switch", WM8904_ANALOGUE_OUT2_LEFT,
618 WM8904_ANALOGUE_OUT2_RIGHT, 6, 1, 0),
619
620 SOC_SINGLE("EQ Switch", WM8904_EQ1, 0, 1, 0),
621 SOC_SINGLE("DRC Switch", WM8904_DRC_0, 15, 1, 0),
622 SOC_ENUM("DRC Path", drc_path),
623 SOC_SINGLE("DAC OSRx2 Switch", WM8904_DAC_DIGITAL_1, 6, 1, 0),
624 SOC_SINGLE_BOOL_EXT("DAC Deemphasis Switch", 0,
625 wm8904_get_deemph, wm8904_put_deemph),
626 };
627
628 static const struct snd_kcontrol_new wm8904_snd_controls[] = {
629 SOC_DOUBLE_TLV("Digital Sidetone Volume", WM8904_DAC_DIGITAL_0, 4, 8, 15, 0,
630 sidetone_tlv),
631 };
632
633 static const struct snd_kcontrol_new wm8904_eq_controls[] = {
634 SOC_SINGLE_TLV("EQ1 Volume", WM8904_EQ2, 0, 24, 0, eq_tlv),
635 SOC_SINGLE_TLV("EQ2 Volume", WM8904_EQ3, 0, 24, 0, eq_tlv),
636 SOC_SINGLE_TLV("EQ3 Volume", WM8904_EQ4, 0, 24, 0, eq_tlv),
637 SOC_SINGLE_TLV("EQ4 Volume", WM8904_EQ5, 0, 24, 0, eq_tlv),
638 SOC_SINGLE_TLV("EQ5 Volume", WM8904_EQ6, 0, 24, 0, eq_tlv),
639 };
640
cp_event(struct snd_soc_dapm_widget * w,struct snd_kcontrol * kcontrol,int event)641 static int cp_event(struct snd_soc_dapm_widget *w,
642 struct snd_kcontrol *kcontrol, int event)
643 {
644 if (WARN_ON(event != SND_SOC_DAPM_POST_PMU))
645 return -EINVAL;
646
647 /* Maximum startup time */
648 udelay(500);
649
650 return 0;
651 }
652
sysclk_event(struct snd_soc_dapm_widget * w,struct snd_kcontrol * kcontrol,int event)653 static int sysclk_event(struct snd_soc_dapm_widget *w,
654 struct snd_kcontrol *kcontrol, int event)
655 {
656 struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
657 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
658
659 switch (event) {
660 case SND_SOC_DAPM_PRE_PMU:
661 /* If we're using the FLL then we only start it when
662 * required; we assume that the configuration has been
663 * done previously and all we need to do is kick it
664 * off.
665 */
666 switch (wm8904->sysclk_src) {
667 case WM8904_CLK_FLL:
668 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
669 WM8904_FLL_OSC_ENA,
670 WM8904_FLL_OSC_ENA);
671
672 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
673 WM8904_FLL_ENA,
674 WM8904_FLL_ENA);
675 break;
676
677 default:
678 break;
679 }
680 break;
681
682 case SND_SOC_DAPM_POST_PMD:
683 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
684 WM8904_FLL_OSC_ENA | WM8904_FLL_ENA, 0);
685 break;
686 }
687
688 return 0;
689 }
690
out_pga_event(struct snd_soc_dapm_widget * w,struct snd_kcontrol * kcontrol,int event)691 static int out_pga_event(struct snd_soc_dapm_widget *w,
692 struct snd_kcontrol *kcontrol, int event)
693 {
694 struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
695 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
696 int reg, val;
697 int dcs_mask;
698 int dcs_l, dcs_r;
699 int dcs_l_reg, dcs_r_reg;
700 int an_out_reg;
701 int timeout;
702 int pwr_reg;
703
704 /* This code is shared between HP and LINEOUT; we do all our
705 * power management in stereo pairs to avoid latency issues so
706 * we reuse shift to identify which rather than strcmp() the
707 * name. */
708 reg = w->shift;
709
710 switch (reg) {
711 case WM8904_ANALOGUE_HP_0:
712 pwr_reg = WM8904_POWER_MANAGEMENT_2;
713 dcs_mask = WM8904_DCS_ENA_CHAN_0 | WM8904_DCS_ENA_CHAN_1;
714 dcs_r_reg = WM8904_DC_SERVO_8;
715 dcs_l_reg = WM8904_DC_SERVO_9;
716 an_out_reg = WM8904_ANALOGUE_OUT1_LEFT;
717 dcs_l = 0;
718 dcs_r = 1;
719 break;
720 case WM8904_ANALOGUE_LINEOUT_0:
721 pwr_reg = WM8904_POWER_MANAGEMENT_3;
722 dcs_mask = WM8904_DCS_ENA_CHAN_2 | WM8904_DCS_ENA_CHAN_3;
723 dcs_r_reg = WM8904_DC_SERVO_6;
724 dcs_l_reg = WM8904_DC_SERVO_7;
725 an_out_reg = WM8904_ANALOGUE_OUT2_LEFT;
726 dcs_l = 2;
727 dcs_r = 3;
728 break;
729 default:
730 WARN(1, "Invalid reg %d\n", reg);
731 return -EINVAL;
732 }
733
734 switch (event) {
735 case SND_SOC_DAPM_PRE_PMU:
736 /* Power on the PGAs */
737 snd_soc_component_update_bits(component, pwr_reg,
738 WM8904_HPL_PGA_ENA | WM8904_HPR_PGA_ENA,
739 WM8904_HPL_PGA_ENA | WM8904_HPR_PGA_ENA);
740
741 /* Power on the amplifier */
742 snd_soc_component_update_bits(component, reg,
743 WM8904_HPL_ENA | WM8904_HPR_ENA,
744 WM8904_HPL_ENA | WM8904_HPR_ENA);
745
746
747 /* Enable the first stage */
748 snd_soc_component_update_bits(component, reg,
749 WM8904_HPL_ENA_DLY | WM8904_HPR_ENA_DLY,
750 WM8904_HPL_ENA_DLY | WM8904_HPR_ENA_DLY);
751
752 /* Power up the DC servo */
753 snd_soc_component_update_bits(component, WM8904_DC_SERVO_0,
754 dcs_mask, dcs_mask);
755
756 /* Either calibrate the DC servo or restore cached state
757 * if we have that.
758 */
759 if (wm8904->dcs_state[dcs_l] || wm8904->dcs_state[dcs_r]) {
760 dev_dbg(component->dev, "Restoring DC servo state\n");
761
762 snd_soc_component_write(component, dcs_l_reg,
763 wm8904->dcs_state[dcs_l]);
764 snd_soc_component_write(component, dcs_r_reg,
765 wm8904->dcs_state[dcs_r]);
766
767 snd_soc_component_write(component, WM8904_DC_SERVO_1, dcs_mask);
768
769 timeout = 20;
770 } else {
771 dev_dbg(component->dev, "Calibrating DC servo\n");
772
773 snd_soc_component_write(component, WM8904_DC_SERVO_1,
774 dcs_mask << WM8904_DCS_TRIG_STARTUP_0_SHIFT);
775
776 timeout = 500;
777 }
778
779 /* Wait for DC servo to complete */
780 dcs_mask <<= WM8904_DCS_CAL_COMPLETE_SHIFT;
781 do {
782 val = snd_soc_component_read(component, WM8904_DC_SERVO_READBACK_0);
783 if ((val & dcs_mask) == dcs_mask)
784 break;
785
786 msleep(1);
787 } while (--timeout);
788
789 if ((val & dcs_mask) != dcs_mask)
790 dev_warn(component->dev, "DC servo timed out\n");
791 else
792 dev_dbg(component->dev, "DC servo ready\n");
793
794 /* Enable the output stage */
795 snd_soc_component_update_bits(component, reg,
796 WM8904_HPL_ENA_OUTP | WM8904_HPR_ENA_OUTP,
797 WM8904_HPL_ENA_OUTP | WM8904_HPR_ENA_OUTP);
798
799 /* Update volume, requires PGA to be powered */
800 val = snd_soc_component_read(component, an_out_reg);
801 snd_soc_component_write(component, an_out_reg, val);
802 break;
803
804 case SND_SOC_DAPM_POST_PMU:
805 /* Unshort the output itself */
806 snd_soc_component_update_bits(component, reg,
807 WM8904_HPL_RMV_SHORT |
808 WM8904_HPR_RMV_SHORT,
809 WM8904_HPL_RMV_SHORT |
810 WM8904_HPR_RMV_SHORT);
811
812 break;
813
814 case SND_SOC_DAPM_PRE_PMD:
815 /* Short the output */
816 snd_soc_component_update_bits(component, reg,
817 WM8904_HPL_RMV_SHORT |
818 WM8904_HPR_RMV_SHORT, 0);
819 break;
820
821 case SND_SOC_DAPM_POST_PMD:
822 /* Cache the DC servo configuration; this will be
823 * invalidated if we change the configuration. */
824 wm8904->dcs_state[dcs_l] = snd_soc_component_read(component, dcs_l_reg);
825 wm8904->dcs_state[dcs_r] = snd_soc_component_read(component, dcs_r_reg);
826
827 snd_soc_component_update_bits(component, WM8904_DC_SERVO_0,
828 dcs_mask, 0);
829
830 /* Disable the amplifier input and output stages */
831 snd_soc_component_update_bits(component, reg,
832 WM8904_HPL_ENA | WM8904_HPR_ENA |
833 WM8904_HPL_ENA_DLY | WM8904_HPR_ENA_DLY |
834 WM8904_HPL_ENA_OUTP | WM8904_HPR_ENA_OUTP,
835 0);
836
837 /* PGAs too */
838 snd_soc_component_update_bits(component, pwr_reg,
839 WM8904_HPL_PGA_ENA | WM8904_HPR_PGA_ENA,
840 0);
841 break;
842 }
843
844 return 0;
845 }
846
847 static const char *input_mode_text[] = {
848 "Single-Ended", "Differential Line", "Differential Mic"
849 };
850
851 static const char *lin_text[] = {
852 "IN1L", "IN2L", "IN3L"
853 };
854
855 static SOC_ENUM_SINGLE_DECL(lin_enum, WM8904_ANALOGUE_LEFT_INPUT_1, 2,
856 lin_text);
857
858 static const struct snd_kcontrol_new lin_mux =
859 SOC_DAPM_ENUM("Left Capture Mux", lin_enum);
860
861 static SOC_ENUM_SINGLE_DECL(lin_inv_enum, WM8904_ANALOGUE_LEFT_INPUT_1, 4,
862 lin_text);
863
864 static const struct snd_kcontrol_new lin_inv_mux =
865 SOC_DAPM_ENUM("Left Capture Inverting Mux", lin_inv_enum);
866
867 static SOC_ENUM_SINGLE_DECL(lin_mode_enum,
868 WM8904_ANALOGUE_LEFT_INPUT_1, 0,
869 input_mode_text);
870
871 static const struct snd_kcontrol_new lin_mode =
872 SOC_DAPM_ENUM("Left Capture Mode", lin_mode_enum);
873
874 static const char *rin_text[] = {
875 "IN1R", "IN2R", "IN3R"
876 };
877
878 static SOC_ENUM_SINGLE_DECL(rin_enum, WM8904_ANALOGUE_RIGHT_INPUT_1, 2,
879 rin_text);
880
881 static const struct snd_kcontrol_new rin_mux =
882 SOC_DAPM_ENUM("Right Capture Mux", rin_enum);
883
884 static SOC_ENUM_SINGLE_DECL(rin_inv_enum, WM8904_ANALOGUE_RIGHT_INPUT_1, 4,
885 rin_text);
886
887 static const struct snd_kcontrol_new rin_inv_mux =
888 SOC_DAPM_ENUM("Right Capture Inverting Mux", rin_inv_enum);
889
890 static SOC_ENUM_SINGLE_DECL(rin_mode_enum,
891 WM8904_ANALOGUE_RIGHT_INPUT_1, 0,
892 input_mode_text);
893
894 static const struct snd_kcontrol_new rin_mode =
895 SOC_DAPM_ENUM("Right Capture Mode", rin_mode_enum);
896
897 static const char *aif_text[] = {
898 "Left", "Right"
899 };
900
901 static SOC_ENUM_SINGLE_DECL(aifoutl_enum, WM8904_AUDIO_INTERFACE_0, 7,
902 aif_text);
903
904 static const struct snd_kcontrol_new aifoutl_mux =
905 SOC_DAPM_ENUM("AIFOUTL Mux", aifoutl_enum);
906
907 static SOC_ENUM_SINGLE_DECL(aifoutr_enum, WM8904_AUDIO_INTERFACE_0, 6,
908 aif_text);
909
910 static const struct snd_kcontrol_new aifoutr_mux =
911 SOC_DAPM_ENUM("AIFOUTR Mux", aifoutr_enum);
912
913 static SOC_ENUM_SINGLE_DECL(aifinl_enum, WM8904_AUDIO_INTERFACE_0, 5,
914 aif_text);
915
916 static const struct snd_kcontrol_new aifinl_mux =
917 SOC_DAPM_ENUM("AIFINL Mux", aifinl_enum);
918
919 static SOC_ENUM_SINGLE_DECL(aifinr_enum, WM8904_AUDIO_INTERFACE_0, 4,
920 aif_text);
921
922 static const struct snd_kcontrol_new aifinr_mux =
923 SOC_DAPM_ENUM("AIFINR Mux", aifinr_enum);
924
925 static const struct snd_soc_dapm_widget wm8904_core_dapm_widgets[] = {
926 SND_SOC_DAPM_SUPPLY("SYSCLK", WM8904_CLOCK_RATES_2, 2, 0, sysclk_event,
927 SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD),
928 SND_SOC_DAPM_SUPPLY("CLK_DSP", WM8904_CLOCK_RATES_2, 1, 0, NULL, 0),
929 SND_SOC_DAPM_SUPPLY("TOCLK", WM8904_CLOCK_RATES_2, 0, 0, NULL, 0),
930 };
931
932 static const struct snd_soc_dapm_widget wm8904_adc_dapm_widgets[] = {
933 SND_SOC_DAPM_INPUT("IN1L"),
934 SND_SOC_DAPM_INPUT("IN1R"),
935 SND_SOC_DAPM_INPUT("IN2L"),
936 SND_SOC_DAPM_INPUT("IN2R"),
937 SND_SOC_DAPM_INPUT("IN3L"),
938 SND_SOC_DAPM_INPUT("IN3R"),
939
940 SND_SOC_DAPM_SUPPLY("MICBIAS", WM8904_MIC_BIAS_CONTROL_0, 0, 0, NULL, 0),
941
942 SND_SOC_DAPM_MUX("Left Capture Mux", SND_SOC_NOPM, 0, 0, &lin_mux),
943 SND_SOC_DAPM_MUX("Left Capture Inverting Mux", SND_SOC_NOPM, 0, 0,
944 &lin_inv_mux),
945 SND_SOC_DAPM_MUX("Left Capture Mode", SND_SOC_NOPM, 0, 0, &lin_mode),
946 SND_SOC_DAPM_MUX("Right Capture Mux", SND_SOC_NOPM, 0, 0, &rin_mux),
947 SND_SOC_DAPM_MUX("Right Capture Inverting Mux", SND_SOC_NOPM, 0, 0,
948 &rin_inv_mux),
949 SND_SOC_DAPM_MUX("Right Capture Mode", SND_SOC_NOPM, 0, 0, &rin_mode),
950
951 SND_SOC_DAPM_PGA("Left Capture PGA", WM8904_POWER_MANAGEMENT_0, 1, 0,
952 NULL, 0),
953 SND_SOC_DAPM_PGA("Right Capture PGA", WM8904_POWER_MANAGEMENT_0, 0, 0,
954 NULL, 0),
955
956 SND_SOC_DAPM_ADC("ADCL", NULL, WM8904_POWER_MANAGEMENT_6, 1, 0),
957 SND_SOC_DAPM_ADC("ADCR", NULL, WM8904_POWER_MANAGEMENT_6, 0, 0),
958
959 SND_SOC_DAPM_MUX("AIFOUTL Mux", SND_SOC_NOPM, 0, 0, &aifoutl_mux),
960 SND_SOC_DAPM_MUX("AIFOUTR Mux", SND_SOC_NOPM, 0, 0, &aifoutr_mux),
961
962 SND_SOC_DAPM_AIF_OUT("AIFOUTL", "Capture", 0, SND_SOC_NOPM, 0, 0),
963 SND_SOC_DAPM_AIF_OUT("AIFOUTR", "Capture", 1, SND_SOC_NOPM, 0, 0),
964 };
965
966 static const struct snd_soc_dapm_widget wm8904_dac_dapm_widgets[] = {
967 SND_SOC_DAPM_AIF_IN("AIFINL", "Playback", 0, SND_SOC_NOPM, 0, 0),
968 SND_SOC_DAPM_AIF_IN("AIFINR", "Playback", 1, SND_SOC_NOPM, 0, 0),
969
970 SND_SOC_DAPM_MUX("DACL Mux", SND_SOC_NOPM, 0, 0, &aifinl_mux),
971 SND_SOC_DAPM_MUX("DACR Mux", SND_SOC_NOPM, 0, 0, &aifinr_mux),
972
973 SND_SOC_DAPM_DAC("DACL", NULL, WM8904_POWER_MANAGEMENT_6, 3, 0),
974 SND_SOC_DAPM_DAC("DACR", NULL, WM8904_POWER_MANAGEMENT_6, 2, 0),
975
976 SND_SOC_DAPM_SUPPLY("Charge pump", WM8904_CHARGE_PUMP_0, 0, 0, cp_event,
977 SND_SOC_DAPM_POST_PMU),
978
979 SND_SOC_DAPM_PGA("HPL PGA", SND_SOC_NOPM, 1, 0, NULL, 0),
980 SND_SOC_DAPM_PGA("HPR PGA", SND_SOC_NOPM, 0, 0, NULL, 0),
981
982 SND_SOC_DAPM_PGA("LINEL PGA", SND_SOC_NOPM, 1, 0, NULL, 0),
983 SND_SOC_DAPM_PGA("LINER PGA", SND_SOC_NOPM, 0, 0, NULL, 0),
984
985 SND_SOC_DAPM_PGA_E("Headphone Output", SND_SOC_NOPM, WM8904_ANALOGUE_HP_0,
986 0, NULL, 0, out_pga_event,
987 SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU |
988 SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMD),
989 SND_SOC_DAPM_PGA_E("Line Output", SND_SOC_NOPM, WM8904_ANALOGUE_LINEOUT_0,
990 0, NULL, 0, out_pga_event,
991 SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMU |
992 SND_SOC_DAPM_PRE_PMD | SND_SOC_DAPM_POST_PMD),
993
994 SND_SOC_DAPM_OUTPUT("HPOUTL"),
995 SND_SOC_DAPM_OUTPUT("HPOUTR"),
996 SND_SOC_DAPM_OUTPUT("LINEOUTL"),
997 SND_SOC_DAPM_OUTPUT("LINEOUTR"),
998 };
999
1000 static const char *out_mux_text[] = {
1001 "DAC", "Bypass"
1002 };
1003
1004 static SOC_ENUM_SINGLE_DECL(hpl_enum, WM8904_ANALOGUE_OUT12_ZC, 3,
1005 out_mux_text);
1006
1007 static const struct snd_kcontrol_new hpl_mux =
1008 SOC_DAPM_ENUM("HPL Mux", hpl_enum);
1009
1010 static SOC_ENUM_SINGLE_DECL(hpr_enum, WM8904_ANALOGUE_OUT12_ZC, 2,
1011 out_mux_text);
1012
1013 static const struct snd_kcontrol_new hpr_mux =
1014 SOC_DAPM_ENUM("HPR Mux", hpr_enum);
1015
1016 static SOC_ENUM_SINGLE_DECL(linel_enum, WM8904_ANALOGUE_OUT12_ZC, 1,
1017 out_mux_text);
1018
1019 static const struct snd_kcontrol_new linel_mux =
1020 SOC_DAPM_ENUM("LINEL Mux", linel_enum);
1021
1022 static SOC_ENUM_SINGLE_DECL(liner_enum, WM8904_ANALOGUE_OUT12_ZC, 0,
1023 out_mux_text);
1024
1025 static const struct snd_kcontrol_new liner_mux =
1026 SOC_DAPM_ENUM("LINER Mux", liner_enum);
1027
1028 static const char *sidetone_text[] = {
1029 "None", "Left", "Right"
1030 };
1031
1032 static SOC_ENUM_SINGLE_DECL(dacl_sidetone_enum, WM8904_DAC_DIGITAL_0, 2,
1033 sidetone_text);
1034
1035 static const struct snd_kcontrol_new dacl_sidetone_mux =
1036 SOC_DAPM_ENUM("Left Sidetone Mux", dacl_sidetone_enum);
1037
1038 static SOC_ENUM_SINGLE_DECL(dacr_sidetone_enum, WM8904_DAC_DIGITAL_0, 0,
1039 sidetone_text);
1040
1041 static const struct snd_kcontrol_new dacr_sidetone_mux =
1042 SOC_DAPM_ENUM("Right Sidetone Mux", dacr_sidetone_enum);
1043
1044 static const struct snd_soc_dapm_widget wm8904_dapm_widgets[] = {
1045 SND_SOC_DAPM_SUPPLY("Class G", WM8904_CLASS_W_0, 0, 1, NULL, 0),
1046 SND_SOC_DAPM_PGA("Left Bypass", SND_SOC_NOPM, 0, 0, NULL, 0),
1047 SND_SOC_DAPM_PGA("Right Bypass", SND_SOC_NOPM, 0, 0, NULL, 0),
1048
1049 SND_SOC_DAPM_MUX("Left Sidetone", SND_SOC_NOPM, 0, 0, &dacl_sidetone_mux),
1050 SND_SOC_DAPM_MUX("Right Sidetone", SND_SOC_NOPM, 0, 0, &dacr_sidetone_mux),
1051
1052 SND_SOC_DAPM_MUX("HPL Mux", SND_SOC_NOPM, 0, 0, &hpl_mux),
1053 SND_SOC_DAPM_MUX("HPR Mux", SND_SOC_NOPM, 0, 0, &hpr_mux),
1054 SND_SOC_DAPM_MUX("LINEL Mux", SND_SOC_NOPM, 0, 0, &linel_mux),
1055 SND_SOC_DAPM_MUX("LINER Mux", SND_SOC_NOPM, 0, 0, &liner_mux),
1056 };
1057
1058 static const struct snd_soc_dapm_route core_intercon[] = {
1059 { "CLK_DSP", NULL, "SYSCLK" },
1060 { "TOCLK", NULL, "SYSCLK" },
1061 };
1062
1063 static const struct snd_soc_dapm_route adc_intercon[] = {
1064 { "Left Capture Mux", "IN1L", "IN1L" },
1065 { "Left Capture Mux", "IN2L", "IN2L" },
1066 { "Left Capture Mux", "IN3L", "IN3L" },
1067
1068 { "Left Capture Inverting Mux", "IN1L", "IN1L" },
1069 { "Left Capture Inverting Mux", "IN2L", "IN2L" },
1070 { "Left Capture Inverting Mux", "IN3L", "IN3L" },
1071
1072 { "Left Capture Mode", "Single-Ended", "Left Capture Inverting Mux" },
1073 { "Left Capture Mode", "Differential Line", "Left Capture Mux" },
1074 { "Left Capture Mode", "Differential Line", "Left Capture Inverting Mux" },
1075 { "Left Capture Mode", "Differential Mic", "Left Capture Mux" },
1076 { "Left Capture Mode", "Differential Mic", "Left Capture Inverting Mux" },
1077
1078 { "Right Capture Mux", "IN1R", "IN1R" },
1079 { "Right Capture Mux", "IN2R", "IN2R" },
1080 { "Right Capture Mux", "IN3R", "IN3R" },
1081
1082 { "Right Capture Inverting Mux", "IN1R", "IN1R" },
1083 { "Right Capture Inverting Mux", "IN2R", "IN2R" },
1084 { "Right Capture Inverting Mux", "IN3R", "IN3R" },
1085
1086 { "Right Capture Mode", "Single-Ended", "Right Capture Inverting Mux" },
1087 { "Right Capture Mode", "Differential Line", "Right Capture Mux" },
1088 { "Right Capture Mode", "Differential Line", "Right Capture Inverting Mux" },
1089 { "Right Capture Mode", "Differential Mic", "Right Capture Mux" },
1090 { "Right Capture Mode", "Differential Mic", "Right Capture Inverting Mux" },
1091
1092 { "Left Capture PGA", NULL, "Left Capture Mode" },
1093 { "Right Capture PGA", NULL, "Right Capture Mode" },
1094
1095 { "AIFOUTL Mux", "Left", "ADCL" },
1096 { "AIFOUTL Mux", "Right", "ADCR" },
1097 { "AIFOUTR Mux", "Left", "ADCL" },
1098 { "AIFOUTR Mux", "Right", "ADCR" },
1099
1100 { "AIFOUTL", NULL, "AIFOUTL Mux" },
1101 { "AIFOUTR", NULL, "AIFOUTR Mux" },
1102
1103 { "ADCL", NULL, "CLK_DSP" },
1104 { "ADCL", NULL, "Left Capture PGA" },
1105
1106 { "ADCR", NULL, "CLK_DSP" },
1107 { "ADCR", NULL, "Right Capture PGA" },
1108 };
1109
1110 static const struct snd_soc_dapm_route dac_intercon[] = {
1111 { "DACL Mux", "Left", "AIFINL" },
1112 { "DACL Mux", "Right", "AIFINR" },
1113
1114 { "DACR Mux", "Left", "AIFINL" },
1115 { "DACR Mux", "Right", "AIFINR" },
1116
1117 { "DACL", NULL, "DACL Mux" },
1118 { "DACL", NULL, "CLK_DSP" },
1119
1120 { "DACR", NULL, "DACR Mux" },
1121 { "DACR", NULL, "CLK_DSP" },
1122
1123 { "Charge pump", NULL, "SYSCLK" },
1124
1125 { "Headphone Output", NULL, "HPL PGA" },
1126 { "Headphone Output", NULL, "HPR PGA" },
1127 { "Headphone Output", NULL, "Charge pump" },
1128 { "Headphone Output", NULL, "TOCLK" },
1129
1130 { "Line Output", NULL, "LINEL PGA" },
1131 { "Line Output", NULL, "LINER PGA" },
1132 { "Line Output", NULL, "Charge pump" },
1133 { "Line Output", NULL, "TOCLK" },
1134
1135 { "HPOUTL", NULL, "Headphone Output" },
1136 { "HPOUTR", NULL, "Headphone Output" },
1137
1138 { "LINEOUTL", NULL, "Line Output" },
1139 { "LINEOUTR", NULL, "Line Output" },
1140 };
1141
1142 static const struct snd_soc_dapm_route wm8904_intercon[] = {
1143 { "Left Sidetone", "Left", "ADCL" },
1144 { "Left Sidetone", "Right", "ADCR" },
1145 { "DACL", NULL, "Left Sidetone" },
1146
1147 { "Right Sidetone", "Left", "ADCL" },
1148 { "Right Sidetone", "Right", "ADCR" },
1149 { "DACR", NULL, "Right Sidetone" },
1150
1151 { "Left Bypass", NULL, "Class G" },
1152 { "Left Bypass", NULL, "Left Capture PGA" },
1153
1154 { "Right Bypass", NULL, "Class G" },
1155 { "Right Bypass", NULL, "Right Capture PGA" },
1156
1157 { "HPL Mux", "DAC", "DACL" },
1158 { "HPL Mux", "Bypass", "Left Bypass" },
1159
1160 { "HPR Mux", "DAC", "DACR" },
1161 { "HPR Mux", "Bypass", "Right Bypass" },
1162
1163 { "LINEL Mux", "DAC", "DACL" },
1164 { "LINEL Mux", "Bypass", "Left Bypass" },
1165
1166 { "LINER Mux", "DAC", "DACR" },
1167 { "LINER Mux", "Bypass", "Right Bypass" },
1168
1169 { "HPL PGA", NULL, "HPL Mux" },
1170 { "HPR PGA", NULL, "HPR Mux" },
1171
1172 { "LINEL PGA", NULL, "LINEL Mux" },
1173 { "LINER PGA", NULL, "LINER Mux" },
1174 };
1175
1176 static const struct snd_soc_dapm_route wm8912_intercon[] = {
1177 { "HPL PGA", NULL, "DACL" },
1178 { "HPR PGA", NULL, "DACR" },
1179
1180 { "LINEL PGA", NULL, "DACL" },
1181 { "LINER PGA", NULL, "DACR" },
1182 };
1183
wm8904_add_widgets(struct snd_soc_component * component)1184 static int wm8904_add_widgets(struct snd_soc_component *component)
1185 {
1186 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
1187 struct snd_soc_dapm_context *dapm = snd_soc_component_get_dapm(component);
1188
1189 snd_soc_dapm_new_controls(dapm, wm8904_core_dapm_widgets,
1190 ARRAY_SIZE(wm8904_core_dapm_widgets));
1191 snd_soc_dapm_add_routes(dapm, core_intercon,
1192 ARRAY_SIZE(core_intercon));
1193
1194 switch (wm8904->devtype) {
1195 case WM8904:
1196 snd_soc_add_component_controls(component, wm8904_adc_snd_controls,
1197 ARRAY_SIZE(wm8904_adc_snd_controls));
1198 snd_soc_add_component_controls(component, wm8904_dac_snd_controls,
1199 ARRAY_SIZE(wm8904_dac_snd_controls));
1200 snd_soc_add_component_controls(component, wm8904_snd_controls,
1201 ARRAY_SIZE(wm8904_snd_controls));
1202
1203 snd_soc_dapm_new_controls(dapm, wm8904_adc_dapm_widgets,
1204 ARRAY_SIZE(wm8904_adc_dapm_widgets));
1205 snd_soc_dapm_new_controls(dapm, wm8904_dac_dapm_widgets,
1206 ARRAY_SIZE(wm8904_dac_dapm_widgets));
1207 snd_soc_dapm_new_controls(dapm, wm8904_dapm_widgets,
1208 ARRAY_SIZE(wm8904_dapm_widgets));
1209
1210 snd_soc_dapm_add_routes(dapm, adc_intercon,
1211 ARRAY_SIZE(adc_intercon));
1212 snd_soc_dapm_add_routes(dapm, dac_intercon,
1213 ARRAY_SIZE(dac_intercon));
1214 snd_soc_dapm_add_routes(dapm, wm8904_intercon,
1215 ARRAY_SIZE(wm8904_intercon));
1216 break;
1217
1218 case WM8912:
1219 snd_soc_add_component_controls(component, wm8904_dac_snd_controls,
1220 ARRAY_SIZE(wm8904_dac_snd_controls));
1221
1222 snd_soc_dapm_new_controls(dapm, wm8904_dac_dapm_widgets,
1223 ARRAY_SIZE(wm8904_dac_dapm_widgets));
1224
1225 snd_soc_dapm_add_routes(dapm, dac_intercon,
1226 ARRAY_SIZE(dac_intercon));
1227 snd_soc_dapm_add_routes(dapm, wm8912_intercon,
1228 ARRAY_SIZE(wm8912_intercon));
1229 break;
1230 }
1231
1232 return 0;
1233 }
1234
1235 static struct {
1236 int ratio;
1237 unsigned int clk_sys_rate;
1238 } clk_sys_rates[] = {
1239 { 64, 0 },
1240 { 128, 1 },
1241 { 192, 2 },
1242 { 256, 3 },
1243 { 384, 4 },
1244 { 512, 5 },
1245 { 786, 6 },
1246 { 1024, 7 },
1247 { 1408, 8 },
1248 { 1536, 9 },
1249 };
1250
1251 static struct {
1252 int rate;
1253 int sample_rate;
1254 } sample_rates[] = {
1255 { 8000, 0 },
1256 { 11025, 1 },
1257 { 12000, 1 },
1258 { 16000, 2 },
1259 { 22050, 3 },
1260 { 24000, 3 },
1261 { 32000, 4 },
1262 { 44100, 5 },
1263 { 48000, 5 },
1264 };
1265
1266 static struct {
1267 int div; /* *10 due to .5s */
1268 int bclk_div;
1269 } bclk_divs[] = {
1270 { 10, 0 },
1271 { 15, 1 },
1272 { 20, 2 },
1273 { 30, 3 },
1274 { 40, 4 },
1275 { 50, 5 },
1276 { 55, 6 },
1277 { 60, 7 },
1278 { 80, 8 },
1279 { 100, 9 },
1280 { 110, 10 },
1281 { 120, 11 },
1282 { 160, 12 },
1283 { 200, 13 },
1284 { 220, 14 },
1285 { 240, 16 },
1286 { 200, 17 },
1287 { 320, 18 },
1288 { 440, 19 },
1289 { 480, 20 },
1290 };
1291
1292
wm8904_hw_params(struct snd_pcm_substream * substream,struct snd_pcm_hw_params * params,struct snd_soc_dai * dai)1293 static int wm8904_hw_params(struct snd_pcm_substream *substream,
1294 struct snd_pcm_hw_params *params,
1295 struct snd_soc_dai *dai)
1296 {
1297 struct snd_soc_component *component = dai->component;
1298 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
1299 int ret, i, best, best_val, cur_val;
1300 unsigned int aif1 = 0;
1301 unsigned int aif2 = 0;
1302 unsigned int aif3 = 0;
1303 unsigned int clock1 = 0;
1304 unsigned int dac_digital1 = 0;
1305
1306 /* What BCLK do we need? */
1307 wm8904->fs = params_rate(params);
1308 if (wm8904->tdm_slots) {
1309 dev_dbg(component->dev, "Configuring for %d %d bit TDM slots\n",
1310 wm8904->tdm_slots, wm8904->tdm_width);
1311 wm8904->bclk = snd_soc_calc_bclk(wm8904->fs,
1312 wm8904->tdm_width, 2,
1313 wm8904->tdm_slots);
1314 } else {
1315 wm8904->bclk = snd_soc_params_to_bclk(params);
1316 }
1317
1318 switch (params_width(params)) {
1319 case 16:
1320 break;
1321 case 20:
1322 aif1 |= 0x40;
1323 break;
1324 case 24:
1325 aif1 |= 0x80;
1326 break;
1327 case 32:
1328 aif1 |= 0xc0;
1329 break;
1330 default:
1331 return -EINVAL;
1332 }
1333
1334
1335 dev_dbg(component->dev, "Target BCLK is %dHz\n", wm8904->bclk);
1336
1337 ret = wm8904_configure_clocking(component);
1338 if (ret != 0)
1339 return ret;
1340
1341 /* Select nearest CLK_SYS_RATE */
1342 best = 0;
1343 best_val = abs((wm8904->sysclk_rate / clk_sys_rates[0].ratio)
1344 - wm8904->fs);
1345 for (i = 1; i < ARRAY_SIZE(clk_sys_rates); i++) {
1346 cur_val = abs((wm8904->sysclk_rate /
1347 clk_sys_rates[i].ratio) - wm8904->fs);
1348 if (cur_val < best_val) {
1349 best = i;
1350 best_val = cur_val;
1351 }
1352 }
1353 dev_dbg(component->dev, "Selected CLK_SYS_RATIO of %d\n",
1354 clk_sys_rates[best].ratio);
1355 clock1 |= (clk_sys_rates[best].clk_sys_rate
1356 << WM8904_CLK_SYS_RATE_SHIFT);
1357
1358 /* SAMPLE_RATE */
1359 best = 0;
1360 best_val = abs(wm8904->fs - sample_rates[0].rate);
1361 for (i = 1; i < ARRAY_SIZE(sample_rates); i++) {
1362 /* Closest match */
1363 cur_val = abs(wm8904->fs - sample_rates[i].rate);
1364 if (cur_val < best_val) {
1365 best = i;
1366 best_val = cur_val;
1367 }
1368 }
1369 dev_dbg(component->dev, "Selected SAMPLE_RATE of %dHz\n",
1370 sample_rates[best].rate);
1371 clock1 |= (sample_rates[best].sample_rate
1372 << WM8904_SAMPLE_RATE_SHIFT);
1373
1374 /* Enable sloping stopband filter for low sample rates */
1375 if (wm8904->fs <= 24000)
1376 dac_digital1 |= WM8904_DAC_SB_FILT;
1377
1378 /* BCLK_DIV */
1379 best = 0;
1380 best_val = INT_MAX;
1381 for (i = 0; i < ARRAY_SIZE(bclk_divs); i++) {
1382 cur_val = ((wm8904->sysclk_rate * 10) / bclk_divs[i].div)
1383 - wm8904->bclk;
1384 if (cur_val < 0) /* Table is sorted */
1385 break;
1386 if (cur_val < best_val) {
1387 best = i;
1388 best_val = cur_val;
1389 }
1390 }
1391 wm8904->bclk = (wm8904->sysclk_rate * 10) / bclk_divs[best].div;
1392 dev_dbg(component->dev, "Selected BCLK_DIV of %d for %dHz BCLK\n",
1393 bclk_divs[best].div, wm8904->bclk);
1394 aif2 |= bclk_divs[best].bclk_div;
1395
1396 /* LRCLK is a simple fraction of BCLK */
1397 dev_dbg(component->dev, "LRCLK_RATE is %d\n", wm8904->bclk / wm8904->fs);
1398 aif3 |= wm8904->bclk / wm8904->fs;
1399
1400 /* Apply the settings */
1401 snd_soc_component_update_bits(component, WM8904_DAC_DIGITAL_1,
1402 WM8904_DAC_SB_FILT, dac_digital1);
1403 snd_soc_component_update_bits(component, WM8904_AUDIO_INTERFACE_1,
1404 WM8904_AIF_WL_MASK, aif1);
1405 snd_soc_component_update_bits(component, WM8904_AUDIO_INTERFACE_2,
1406 WM8904_BCLK_DIV_MASK, aif2);
1407 snd_soc_component_update_bits(component, WM8904_AUDIO_INTERFACE_3,
1408 WM8904_LRCLK_RATE_MASK, aif3);
1409 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_1,
1410 WM8904_SAMPLE_RATE_MASK |
1411 WM8904_CLK_SYS_RATE_MASK, clock1);
1412
1413 /* Update filters for the new settings */
1414 wm8904_set_retune_mobile(component);
1415 wm8904_set_deemph(component);
1416
1417 return 0;
1418 }
1419
wm8904_set_fmt(struct snd_soc_dai * dai,unsigned int fmt)1420 static int wm8904_set_fmt(struct snd_soc_dai *dai, unsigned int fmt)
1421 {
1422 struct snd_soc_component *component = dai->component;
1423 unsigned int aif1 = 0;
1424 unsigned int aif3 = 0;
1425
1426 switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
1427 case SND_SOC_DAIFMT_CBS_CFS:
1428 break;
1429 case SND_SOC_DAIFMT_CBS_CFM:
1430 aif3 |= WM8904_LRCLK_DIR;
1431 break;
1432 case SND_SOC_DAIFMT_CBM_CFS:
1433 aif1 |= WM8904_BCLK_DIR;
1434 break;
1435 case SND_SOC_DAIFMT_CBM_CFM:
1436 aif1 |= WM8904_BCLK_DIR;
1437 aif3 |= WM8904_LRCLK_DIR;
1438 break;
1439 default:
1440 return -EINVAL;
1441 }
1442
1443 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
1444 case SND_SOC_DAIFMT_DSP_B:
1445 aif1 |= 0x3 | WM8904_AIF_LRCLK_INV;
1446 fallthrough;
1447 case SND_SOC_DAIFMT_DSP_A:
1448 aif1 |= 0x3;
1449 break;
1450 case SND_SOC_DAIFMT_I2S:
1451 aif1 |= 0x2;
1452 break;
1453 case SND_SOC_DAIFMT_RIGHT_J:
1454 break;
1455 case SND_SOC_DAIFMT_LEFT_J:
1456 aif1 |= 0x1;
1457 break;
1458 default:
1459 return -EINVAL;
1460 }
1461
1462 switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
1463 case SND_SOC_DAIFMT_DSP_A:
1464 case SND_SOC_DAIFMT_DSP_B:
1465 /* frame inversion not valid for DSP modes */
1466 switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
1467 case SND_SOC_DAIFMT_NB_NF:
1468 break;
1469 case SND_SOC_DAIFMT_IB_NF:
1470 aif1 |= WM8904_AIF_BCLK_INV;
1471 break;
1472 default:
1473 return -EINVAL;
1474 }
1475 break;
1476
1477 case SND_SOC_DAIFMT_I2S:
1478 case SND_SOC_DAIFMT_RIGHT_J:
1479 case SND_SOC_DAIFMT_LEFT_J:
1480 switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
1481 case SND_SOC_DAIFMT_NB_NF:
1482 break;
1483 case SND_SOC_DAIFMT_IB_IF:
1484 aif1 |= WM8904_AIF_BCLK_INV | WM8904_AIF_LRCLK_INV;
1485 break;
1486 case SND_SOC_DAIFMT_IB_NF:
1487 aif1 |= WM8904_AIF_BCLK_INV;
1488 break;
1489 case SND_SOC_DAIFMT_NB_IF:
1490 aif1 |= WM8904_AIF_LRCLK_INV;
1491 break;
1492 default:
1493 return -EINVAL;
1494 }
1495 break;
1496 default:
1497 return -EINVAL;
1498 }
1499
1500 snd_soc_component_update_bits(component, WM8904_AUDIO_INTERFACE_1,
1501 WM8904_AIF_BCLK_INV | WM8904_AIF_LRCLK_INV |
1502 WM8904_AIF_FMT_MASK | WM8904_BCLK_DIR, aif1);
1503 snd_soc_component_update_bits(component, WM8904_AUDIO_INTERFACE_3,
1504 WM8904_LRCLK_DIR, aif3);
1505
1506 return 0;
1507 }
1508
1509
wm8904_set_tdm_slot(struct snd_soc_dai * dai,unsigned int tx_mask,unsigned int rx_mask,int slots,int slot_width)1510 static int wm8904_set_tdm_slot(struct snd_soc_dai *dai, unsigned int tx_mask,
1511 unsigned int rx_mask, int slots, int slot_width)
1512 {
1513 struct snd_soc_component *component = dai->component;
1514 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
1515 int aif1 = 0;
1516
1517 /* Don't need to validate anything if we're turning off TDM */
1518 if (slots == 0)
1519 goto out;
1520
1521 /* Note that we allow configurations we can't handle ourselves -
1522 * for example, we can generate clocks for slots 2 and up even if
1523 * we can't use those slots ourselves.
1524 */
1525 aif1 |= WM8904_AIFADC_TDM | WM8904_AIFDAC_TDM;
1526
1527 switch (rx_mask) {
1528 case 3:
1529 break;
1530 case 0xc:
1531 aif1 |= WM8904_AIFADC_TDM_CHAN;
1532 break;
1533 default:
1534 return -EINVAL;
1535 }
1536
1537
1538 switch (tx_mask) {
1539 case 3:
1540 break;
1541 case 0xc:
1542 aif1 |= WM8904_AIFDAC_TDM_CHAN;
1543 break;
1544 default:
1545 return -EINVAL;
1546 }
1547
1548 out:
1549 wm8904->tdm_width = slot_width;
1550 wm8904->tdm_slots = slots / 2;
1551
1552 snd_soc_component_update_bits(component, WM8904_AUDIO_INTERFACE_1,
1553 WM8904_AIFADC_TDM | WM8904_AIFADC_TDM_CHAN |
1554 WM8904_AIFDAC_TDM | WM8904_AIFDAC_TDM_CHAN, aif1);
1555
1556 return 0;
1557 }
1558
1559 struct _fll_div {
1560 u16 fll_fratio;
1561 u16 fll_outdiv;
1562 u16 fll_clk_ref_div;
1563 u16 n;
1564 u16 k;
1565 };
1566
1567 /* The size in bits of the FLL divide multiplied by 10
1568 * to allow rounding later */
1569 #define FIXED_FLL_SIZE ((1 << 16) * 10)
1570
1571 static struct {
1572 unsigned int min;
1573 unsigned int max;
1574 u16 fll_fratio;
1575 int ratio;
1576 } fll_fratios[] = {
1577 { 0, 64000, 4, 16 },
1578 { 64000, 128000, 3, 8 },
1579 { 128000, 256000, 2, 4 },
1580 { 256000, 1000000, 1, 2 },
1581 { 1000000, 13500000, 0, 1 },
1582 };
1583
fll_factors(struct _fll_div * fll_div,unsigned int Fref,unsigned int Fout)1584 static int fll_factors(struct _fll_div *fll_div, unsigned int Fref,
1585 unsigned int Fout)
1586 {
1587 u64 Kpart;
1588 unsigned int K, Ndiv, Nmod, target;
1589 unsigned int div;
1590 int i;
1591
1592 /* Fref must be <=13.5MHz */
1593 div = 1;
1594 fll_div->fll_clk_ref_div = 0;
1595 while ((Fref / div) > 13500000) {
1596 div *= 2;
1597 fll_div->fll_clk_ref_div++;
1598
1599 if (div > 8) {
1600 pr_err("Can't scale %dMHz input down to <=13.5MHz\n",
1601 Fref);
1602 return -EINVAL;
1603 }
1604 }
1605
1606 pr_debug("Fref=%u Fout=%u\n", Fref, Fout);
1607
1608 /* Apply the division for our remaining calculations */
1609 Fref /= div;
1610
1611 /* Fvco should be 90-100MHz; don't check the upper bound */
1612 div = 4;
1613 while (Fout * div < 90000000) {
1614 div++;
1615 if (div > 64) {
1616 pr_err("Unable to find FLL_OUTDIV for Fout=%uHz\n",
1617 Fout);
1618 return -EINVAL;
1619 }
1620 }
1621 target = Fout * div;
1622 fll_div->fll_outdiv = div - 1;
1623
1624 pr_debug("Fvco=%dHz\n", target);
1625
1626 /* Find an appropriate FLL_FRATIO and factor it out of the target */
1627 for (i = 0; i < ARRAY_SIZE(fll_fratios); i++) {
1628 if (fll_fratios[i].min <= Fref && Fref <= fll_fratios[i].max) {
1629 fll_div->fll_fratio = fll_fratios[i].fll_fratio;
1630 target /= fll_fratios[i].ratio;
1631 break;
1632 }
1633 }
1634 if (i == ARRAY_SIZE(fll_fratios)) {
1635 pr_err("Unable to find FLL_FRATIO for Fref=%uHz\n", Fref);
1636 return -EINVAL;
1637 }
1638
1639 /* Now, calculate N.K */
1640 Ndiv = target / Fref;
1641
1642 fll_div->n = Ndiv;
1643 Nmod = target % Fref;
1644 pr_debug("Nmod=%d\n", Nmod);
1645
1646 /* Calculate fractional part - scale up so we can round. */
1647 Kpart = FIXED_FLL_SIZE * (long long)Nmod;
1648
1649 do_div(Kpart, Fref);
1650
1651 K = Kpart & 0xFFFFFFFF;
1652
1653 if ((K % 10) >= 5)
1654 K += 5;
1655
1656 /* Move down to proper range now rounding is done */
1657 fll_div->k = K / 10;
1658
1659 pr_debug("N=%x K=%x FLL_FRATIO=%x FLL_OUTDIV=%x FLL_CLK_REF_DIV=%x\n",
1660 fll_div->n, fll_div->k,
1661 fll_div->fll_fratio, fll_div->fll_outdiv,
1662 fll_div->fll_clk_ref_div);
1663
1664 return 0;
1665 }
1666
wm8904_set_fll(struct snd_soc_dai * dai,int fll_id,int source,unsigned int Fref,unsigned int Fout)1667 static int wm8904_set_fll(struct snd_soc_dai *dai, int fll_id, int source,
1668 unsigned int Fref, unsigned int Fout)
1669 {
1670 struct snd_soc_component *component = dai->component;
1671 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
1672 struct _fll_div fll_div;
1673 int ret, val;
1674 int clock2, fll1;
1675
1676 /* Any change? */
1677 if (source == wm8904->fll_src && Fref == wm8904->fll_fref &&
1678 Fout == wm8904->fll_fout)
1679 return 0;
1680
1681 clock2 = snd_soc_component_read(component, WM8904_CLOCK_RATES_2);
1682
1683 if (Fout == 0) {
1684 dev_dbg(component->dev, "FLL disabled\n");
1685
1686 wm8904->fll_fref = 0;
1687 wm8904->fll_fout = 0;
1688
1689 /* Gate SYSCLK to avoid glitches */
1690 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_2,
1691 WM8904_CLK_SYS_ENA, 0);
1692
1693 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
1694 WM8904_FLL_OSC_ENA | WM8904_FLL_ENA, 0);
1695
1696 goto out;
1697 }
1698
1699 /* Validate the FLL ID */
1700 switch (source) {
1701 case WM8904_FLL_MCLK:
1702 case WM8904_FLL_LRCLK:
1703 case WM8904_FLL_BCLK:
1704 ret = fll_factors(&fll_div, Fref, Fout);
1705 if (ret != 0)
1706 return ret;
1707 break;
1708
1709 case WM8904_FLL_FREE_RUNNING:
1710 dev_dbg(component->dev, "Using free running FLL\n");
1711 /* Force 12MHz and output/4 for now */
1712 Fout = 12000000;
1713 Fref = 12000000;
1714
1715 memset(&fll_div, 0, sizeof(fll_div));
1716 fll_div.fll_outdiv = 3;
1717 break;
1718
1719 default:
1720 dev_err(component->dev, "Unknown FLL ID %d\n", fll_id);
1721 return -EINVAL;
1722 }
1723
1724 /* Save current state then disable the FLL and SYSCLK to avoid
1725 * misclocking */
1726 fll1 = snd_soc_component_read(component, WM8904_FLL_CONTROL_1);
1727 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_2,
1728 WM8904_CLK_SYS_ENA, 0);
1729 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
1730 WM8904_FLL_OSC_ENA | WM8904_FLL_ENA, 0);
1731
1732 /* Unlock forced oscilator control to switch it on/off */
1733 snd_soc_component_update_bits(component, WM8904_CONTROL_INTERFACE_TEST_1,
1734 WM8904_USER_KEY, WM8904_USER_KEY);
1735
1736 if (fll_id == WM8904_FLL_FREE_RUNNING) {
1737 val = WM8904_FLL_FRC_NCO;
1738 } else {
1739 val = 0;
1740 }
1741
1742 snd_soc_component_update_bits(component, WM8904_FLL_NCO_TEST_1, WM8904_FLL_FRC_NCO,
1743 val);
1744 snd_soc_component_update_bits(component, WM8904_CONTROL_INTERFACE_TEST_1,
1745 WM8904_USER_KEY, 0);
1746
1747 switch (fll_id) {
1748 case WM8904_FLL_MCLK:
1749 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_5,
1750 WM8904_FLL_CLK_REF_SRC_MASK, 0);
1751 break;
1752
1753 case WM8904_FLL_LRCLK:
1754 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_5,
1755 WM8904_FLL_CLK_REF_SRC_MASK, 1);
1756 break;
1757
1758 case WM8904_FLL_BCLK:
1759 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_5,
1760 WM8904_FLL_CLK_REF_SRC_MASK, 2);
1761 break;
1762 }
1763
1764 if (fll_div.k)
1765 val = WM8904_FLL_FRACN_ENA;
1766 else
1767 val = 0;
1768 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
1769 WM8904_FLL_FRACN_ENA, val);
1770
1771 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_2,
1772 WM8904_FLL_OUTDIV_MASK | WM8904_FLL_FRATIO_MASK,
1773 (fll_div.fll_outdiv << WM8904_FLL_OUTDIV_SHIFT) |
1774 (fll_div.fll_fratio << WM8904_FLL_FRATIO_SHIFT));
1775
1776 snd_soc_component_write(component, WM8904_FLL_CONTROL_3, fll_div.k);
1777
1778 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_4, WM8904_FLL_N_MASK,
1779 fll_div.n << WM8904_FLL_N_SHIFT);
1780
1781 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_5,
1782 WM8904_FLL_CLK_REF_DIV_MASK,
1783 fll_div.fll_clk_ref_div
1784 << WM8904_FLL_CLK_REF_DIV_SHIFT);
1785
1786 dev_dbg(component->dev, "FLL configured for %dHz->%dHz\n", Fref, Fout);
1787
1788 wm8904->fll_fref = Fref;
1789 wm8904->fll_fout = Fout;
1790 wm8904->fll_src = source;
1791
1792 /* Enable the FLL if it was previously active */
1793 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
1794 WM8904_FLL_OSC_ENA, fll1);
1795 snd_soc_component_update_bits(component, WM8904_FLL_CONTROL_1,
1796 WM8904_FLL_ENA, fll1);
1797
1798 out:
1799 /* Reenable SYSCLK if it was previously active */
1800 snd_soc_component_update_bits(component, WM8904_CLOCK_RATES_2,
1801 WM8904_CLK_SYS_ENA, clock2);
1802
1803 return 0;
1804 }
1805
wm8904_set_sysclk(struct snd_soc_dai * dai,int clk_id,unsigned int freq,int dir)1806 static int wm8904_set_sysclk(struct snd_soc_dai *dai, int clk_id,
1807 unsigned int freq, int dir)
1808 {
1809 struct snd_soc_component *component = dai->component;
1810 struct wm8904_priv *priv = snd_soc_component_get_drvdata(component);
1811 unsigned long mclk_freq;
1812 int ret;
1813
1814 switch (clk_id) {
1815 case WM8904_CLK_AUTO:
1816 /* We don't have any rate constraints, so just ignore the
1817 * request to disable constraining.
1818 */
1819 if (!freq)
1820 return 0;
1821
1822 mclk_freq = clk_get_rate(priv->mclk);
1823 /* enable FLL if a different sysclk is desired */
1824 if (mclk_freq != freq) {
1825 priv->sysclk_src = WM8904_CLK_FLL;
1826 ret = wm8904_set_fll(dai, WM8904_FLL_MCLK,
1827 WM8904_FLL_MCLK,
1828 mclk_freq, freq);
1829 if (ret)
1830 return ret;
1831 break;
1832 }
1833 clk_id = WM8904_CLK_MCLK;
1834 fallthrough;
1835
1836 case WM8904_CLK_MCLK:
1837 priv->sysclk_src = clk_id;
1838 priv->mclk_rate = freq;
1839 break;
1840
1841 case WM8904_CLK_FLL:
1842 priv->sysclk_src = clk_id;
1843 break;
1844
1845 default:
1846 return -EINVAL;
1847 }
1848
1849 dev_dbg(dai->dev, "Clock source is %d at %uHz\n", clk_id, freq);
1850
1851 wm8904_configure_clocking(component);
1852
1853 return 0;
1854 }
1855
wm8904_mute(struct snd_soc_dai * codec_dai,int mute,int direction)1856 static int wm8904_mute(struct snd_soc_dai *codec_dai, int mute, int direction)
1857 {
1858 struct snd_soc_component *component = codec_dai->component;
1859 int val;
1860
1861 if (mute)
1862 val = WM8904_DAC_MUTE;
1863 else
1864 val = 0;
1865
1866 snd_soc_component_update_bits(component, WM8904_DAC_DIGITAL_1, WM8904_DAC_MUTE, val);
1867
1868 return 0;
1869 }
1870
wm8904_set_bias_level(struct snd_soc_component * component,enum snd_soc_bias_level level)1871 static int wm8904_set_bias_level(struct snd_soc_component *component,
1872 enum snd_soc_bias_level level)
1873 {
1874 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
1875 int ret;
1876
1877 switch (level) {
1878 case SND_SOC_BIAS_ON:
1879 break;
1880
1881 case SND_SOC_BIAS_PREPARE:
1882 /* VMID resistance 2*50k */
1883 snd_soc_component_update_bits(component, WM8904_VMID_CONTROL_0,
1884 WM8904_VMID_RES_MASK,
1885 0x1 << WM8904_VMID_RES_SHIFT);
1886
1887 /* Normal bias current */
1888 snd_soc_component_update_bits(component, WM8904_BIAS_CONTROL_0,
1889 WM8904_ISEL_MASK, 2 << WM8904_ISEL_SHIFT);
1890 break;
1891
1892 case SND_SOC_BIAS_STANDBY:
1893 if (snd_soc_component_get_bias_level(component) == SND_SOC_BIAS_OFF) {
1894 ret = regulator_bulk_enable(ARRAY_SIZE(wm8904->supplies),
1895 wm8904->supplies);
1896 if (ret != 0) {
1897 dev_err(component->dev,
1898 "Failed to enable supplies: %d\n",
1899 ret);
1900 return ret;
1901 }
1902
1903 ret = clk_prepare_enable(wm8904->mclk);
1904 if (ret) {
1905 dev_err(component->dev,
1906 "Failed to enable MCLK: %d\n", ret);
1907 regulator_bulk_disable(ARRAY_SIZE(wm8904->supplies),
1908 wm8904->supplies);
1909 return ret;
1910 }
1911
1912 regcache_cache_only(wm8904->regmap, false);
1913 regcache_sync(wm8904->regmap);
1914
1915 /* Enable bias */
1916 snd_soc_component_update_bits(component, WM8904_BIAS_CONTROL_0,
1917 WM8904_BIAS_ENA, WM8904_BIAS_ENA);
1918
1919 /* Enable VMID, VMID buffering, 2*5k resistance */
1920 snd_soc_component_update_bits(component, WM8904_VMID_CONTROL_0,
1921 WM8904_VMID_ENA |
1922 WM8904_VMID_RES_MASK,
1923 WM8904_VMID_ENA |
1924 0x3 << WM8904_VMID_RES_SHIFT);
1925
1926 /* Let VMID ramp */
1927 msleep(1);
1928 }
1929
1930 /* Maintain VMID with 2*250k */
1931 snd_soc_component_update_bits(component, WM8904_VMID_CONTROL_0,
1932 WM8904_VMID_RES_MASK,
1933 0x2 << WM8904_VMID_RES_SHIFT);
1934
1935 /* Bias current *0.5 */
1936 snd_soc_component_update_bits(component, WM8904_BIAS_CONTROL_0,
1937 WM8904_ISEL_MASK, 0);
1938 break;
1939
1940 case SND_SOC_BIAS_OFF:
1941 /* Turn off VMID */
1942 snd_soc_component_update_bits(component, WM8904_VMID_CONTROL_0,
1943 WM8904_VMID_RES_MASK | WM8904_VMID_ENA, 0);
1944
1945 /* Stop bias generation */
1946 snd_soc_component_update_bits(component, WM8904_BIAS_CONTROL_0,
1947 WM8904_BIAS_ENA, 0);
1948
1949 snd_soc_component_write(component, WM8904_SW_RESET_AND_ID, 0);
1950 regcache_cache_only(wm8904->regmap, true);
1951 regcache_mark_dirty(wm8904->regmap);
1952
1953 regulator_bulk_disable(ARRAY_SIZE(wm8904->supplies),
1954 wm8904->supplies);
1955 clk_disable_unprepare(wm8904->mclk);
1956 break;
1957 }
1958 return 0;
1959 }
1960
1961 #define WM8904_RATES SNDRV_PCM_RATE_8000_96000
1962
1963 #define WM8904_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S20_3LE |\
1964 SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE)
1965
1966 static const struct snd_soc_dai_ops wm8904_dai_ops = {
1967 .set_sysclk = wm8904_set_sysclk,
1968 .set_fmt = wm8904_set_fmt,
1969 .set_tdm_slot = wm8904_set_tdm_slot,
1970 .set_pll = wm8904_set_fll,
1971 .hw_params = wm8904_hw_params,
1972 .mute_stream = wm8904_mute,
1973 .no_capture_mute = 1,
1974 };
1975
1976 static struct snd_soc_dai_driver wm8904_dai = {
1977 .name = "wm8904-hifi",
1978 .playback = {
1979 .stream_name = "Playback",
1980 .channels_min = 2,
1981 .channels_max = 2,
1982 .rates = WM8904_RATES,
1983 .formats = WM8904_FORMATS,
1984 },
1985 .capture = {
1986 .stream_name = "Capture",
1987 .channels_min = 2,
1988 .channels_max = 2,
1989 .rates = WM8904_RATES,
1990 .formats = WM8904_FORMATS,
1991 },
1992 .ops = &wm8904_dai_ops,
1993 .symmetric_rate = 1,
1994 };
1995
wm8904_handle_retune_mobile_pdata(struct snd_soc_component * component)1996 static void wm8904_handle_retune_mobile_pdata(struct snd_soc_component *component)
1997 {
1998 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
1999 struct wm8904_pdata *pdata = wm8904->pdata;
2000 struct snd_kcontrol_new control =
2001 SOC_ENUM_EXT("EQ Mode",
2002 wm8904->retune_mobile_enum,
2003 wm8904_get_retune_mobile_enum,
2004 wm8904_put_retune_mobile_enum);
2005 int ret, i, j;
2006 const char **t;
2007
2008 /* We need an array of texts for the enum API but the number
2009 * of texts is likely to be less than the number of
2010 * configurations due to the sample rate dependency of the
2011 * configurations. */
2012 wm8904->num_retune_mobile_texts = 0;
2013 wm8904->retune_mobile_texts = NULL;
2014 for (i = 0; i < pdata->num_retune_mobile_cfgs; i++) {
2015 for (j = 0; j < wm8904->num_retune_mobile_texts; j++) {
2016 if (strcmp(pdata->retune_mobile_cfgs[i].name,
2017 wm8904->retune_mobile_texts[j]) == 0)
2018 break;
2019 }
2020
2021 if (j != wm8904->num_retune_mobile_texts)
2022 continue;
2023
2024 /* Expand the array... */
2025 t = krealloc(wm8904->retune_mobile_texts,
2026 sizeof(char *) *
2027 (wm8904->num_retune_mobile_texts + 1),
2028 GFP_KERNEL);
2029 if (t == NULL)
2030 continue;
2031
2032 /* ...store the new entry... */
2033 t[wm8904->num_retune_mobile_texts] =
2034 pdata->retune_mobile_cfgs[i].name;
2035
2036 /* ...and remember the new version. */
2037 wm8904->num_retune_mobile_texts++;
2038 wm8904->retune_mobile_texts = t;
2039 }
2040
2041 dev_dbg(component->dev, "Allocated %d unique ReTune Mobile names\n",
2042 wm8904->num_retune_mobile_texts);
2043
2044 wm8904->retune_mobile_enum.items = wm8904->num_retune_mobile_texts;
2045 wm8904->retune_mobile_enum.texts = wm8904->retune_mobile_texts;
2046
2047 ret = snd_soc_add_component_controls(component, &control, 1);
2048 if (ret != 0)
2049 dev_err(component->dev,
2050 "Failed to add ReTune Mobile control: %d\n", ret);
2051 }
2052
wm8904_handle_pdata(struct snd_soc_component * component)2053 static void wm8904_handle_pdata(struct snd_soc_component *component)
2054 {
2055 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
2056 struct wm8904_pdata *pdata = wm8904->pdata;
2057 int ret, i;
2058
2059 if (!pdata) {
2060 snd_soc_add_component_controls(component, wm8904_eq_controls,
2061 ARRAY_SIZE(wm8904_eq_controls));
2062 return;
2063 }
2064
2065 dev_dbg(component->dev, "%d DRC configurations\n", pdata->num_drc_cfgs);
2066
2067 if (pdata->num_drc_cfgs) {
2068 struct snd_kcontrol_new control =
2069 SOC_ENUM_EXT("DRC Mode", wm8904->drc_enum,
2070 wm8904_get_drc_enum, wm8904_put_drc_enum);
2071
2072 /* We need an array of texts for the enum API */
2073 wm8904->drc_texts = kmalloc_array(pdata->num_drc_cfgs,
2074 sizeof(char *),
2075 GFP_KERNEL);
2076 if (!wm8904->drc_texts)
2077 return;
2078
2079 for (i = 0; i < pdata->num_drc_cfgs; i++)
2080 wm8904->drc_texts[i] = pdata->drc_cfgs[i].name;
2081
2082 wm8904->drc_enum.items = pdata->num_drc_cfgs;
2083 wm8904->drc_enum.texts = wm8904->drc_texts;
2084
2085 ret = snd_soc_add_component_controls(component, &control, 1);
2086 if (ret != 0)
2087 dev_err(component->dev,
2088 "Failed to add DRC mode control: %d\n", ret);
2089
2090 wm8904_set_drc(component);
2091 }
2092
2093 dev_dbg(component->dev, "%d ReTune Mobile configurations\n",
2094 pdata->num_retune_mobile_cfgs);
2095
2096 if (pdata->num_retune_mobile_cfgs)
2097 wm8904_handle_retune_mobile_pdata(component);
2098 else
2099 snd_soc_add_component_controls(component, wm8904_eq_controls,
2100 ARRAY_SIZE(wm8904_eq_controls));
2101 }
2102
2103
wm8904_probe(struct snd_soc_component * component)2104 static int wm8904_probe(struct snd_soc_component *component)
2105 {
2106 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
2107
2108 switch (wm8904->devtype) {
2109 case WM8904:
2110 break;
2111 case WM8912:
2112 memset(&wm8904_dai.capture, 0, sizeof(wm8904_dai.capture));
2113 break;
2114 default:
2115 dev_err(component->dev, "Unknown device type %d\n",
2116 wm8904->devtype);
2117 return -EINVAL;
2118 }
2119
2120 wm8904_handle_pdata(component);
2121
2122 wm8904_add_widgets(component);
2123
2124 return 0;
2125 }
2126
wm8904_remove(struct snd_soc_component * component)2127 static void wm8904_remove(struct snd_soc_component *component)
2128 {
2129 struct wm8904_priv *wm8904 = snd_soc_component_get_drvdata(component);
2130
2131 kfree(wm8904->retune_mobile_texts);
2132 kfree(wm8904->drc_texts);
2133 }
2134
2135 static const struct snd_soc_component_driver soc_component_dev_wm8904 = {
2136 .probe = wm8904_probe,
2137 .remove = wm8904_remove,
2138 .set_bias_level = wm8904_set_bias_level,
2139 .use_pmdown_time = 1,
2140 .endianness = 1,
2141 };
2142
2143 static const struct regmap_config wm8904_regmap = {
2144 .reg_bits = 8,
2145 .val_bits = 16,
2146
2147 .max_register = WM8904_MAX_REGISTER,
2148 .volatile_reg = wm8904_volatile_register,
2149 .readable_reg = wm8904_readable_register,
2150
2151 .cache_type = REGCACHE_MAPLE,
2152 .reg_defaults = wm8904_reg_defaults,
2153 .num_reg_defaults = ARRAY_SIZE(wm8904_reg_defaults),
2154 };
2155
2156 #ifdef CONFIG_OF
2157 static const struct of_device_id wm8904_of_match[] = {
2158 {
2159 .compatible = "wlf,wm8904",
2160 .data = (void *)WM8904,
2161 }, {
2162 .compatible = "wlf,wm8912",
2163 .data = (void *)WM8912,
2164 }, {
2165 /* sentinel */
2166 }
2167 };
2168 MODULE_DEVICE_TABLE(of, wm8904_of_match);
2169 #endif
2170
2171 static const struct i2c_device_id wm8904_i2c_id[];
2172
wm8904_i2c_probe(struct i2c_client * i2c)2173 static int wm8904_i2c_probe(struct i2c_client *i2c)
2174 {
2175 struct wm8904_priv *wm8904;
2176 unsigned int val;
2177 int ret, i;
2178
2179 wm8904 = devm_kzalloc(&i2c->dev, sizeof(struct wm8904_priv),
2180 GFP_KERNEL);
2181 if (wm8904 == NULL)
2182 return -ENOMEM;
2183
2184 wm8904->mclk = devm_clk_get(&i2c->dev, "mclk");
2185 if (IS_ERR(wm8904->mclk)) {
2186 ret = PTR_ERR(wm8904->mclk);
2187 dev_err(&i2c->dev, "Failed to get MCLK\n");
2188 return ret;
2189 }
2190
2191 wm8904->regmap = devm_regmap_init_i2c(i2c, &wm8904_regmap);
2192 if (IS_ERR(wm8904->regmap)) {
2193 ret = PTR_ERR(wm8904->regmap);
2194 dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
2195 ret);
2196 return ret;
2197 }
2198
2199 if (i2c->dev.of_node) {
2200 const struct of_device_id *match;
2201
2202 match = of_match_node(wm8904_of_match, i2c->dev.of_node);
2203 if (match == NULL)
2204 return -EINVAL;
2205 wm8904->devtype = (uintptr_t)match->data;
2206 } else {
2207 const struct i2c_device_id *id =
2208 i2c_match_id(wm8904_i2c_id, i2c);
2209 wm8904->devtype = id->driver_data;
2210 }
2211
2212 i2c_set_clientdata(i2c, wm8904);
2213 wm8904->pdata = i2c->dev.platform_data;
2214
2215 for (i = 0; i < ARRAY_SIZE(wm8904->supplies); i++)
2216 wm8904->supplies[i].supply = wm8904_supply_names[i];
2217
2218 ret = devm_regulator_bulk_get(&i2c->dev, ARRAY_SIZE(wm8904->supplies),
2219 wm8904->supplies);
2220 if (ret != 0) {
2221 dev_err(&i2c->dev, "Failed to request supplies: %d\n", ret);
2222 return ret;
2223 }
2224
2225 ret = regulator_bulk_enable(ARRAY_SIZE(wm8904->supplies),
2226 wm8904->supplies);
2227 if (ret != 0) {
2228 dev_err(&i2c->dev, "Failed to enable supplies: %d\n", ret);
2229 return ret;
2230 }
2231
2232 ret = regmap_read(wm8904->regmap, WM8904_SW_RESET_AND_ID, &val);
2233 if (ret < 0) {
2234 dev_err(&i2c->dev, "Failed to read ID register: %d\n", ret);
2235 goto err_enable;
2236 }
2237 if (val != 0x8904) {
2238 dev_err(&i2c->dev, "Device is not a WM8904, ID is %x\n", val);
2239 ret = -EINVAL;
2240 goto err_enable;
2241 }
2242
2243 ret = regmap_read(wm8904->regmap, WM8904_REVISION, &val);
2244 if (ret < 0) {
2245 dev_err(&i2c->dev, "Failed to read device revision: %d\n",
2246 ret);
2247 goto err_enable;
2248 }
2249 dev_info(&i2c->dev, "revision %c\n", val + 'A');
2250
2251 ret = regmap_write(wm8904->regmap, WM8904_SW_RESET_AND_ID, 0);
2252 if (ret < 0) {
2253 dev_err(&i2c->dev, "Failed to issue reset: %d\n", ret);
2254 goto err_enable;
2255 }
2256
2257 /* Change some default settings - latch VU and enable ZC */
2258 regmap_update_bits(wm8904->regmap, WM8904_ADC_DIGITAL_VOLUME_LEFT,
2259 WM8904_ADC_VU, WM8904_ADC_VU);
2260 regmap_update_bits(wm8904->regmap, WM8904_ADC_DIGITAL_VOLUME_RIGHT,
2261 WM8904_ADC_VU, WM8904_ADC_VU);
2262 regmap_update_bits(wm8904->regmap, WM8904_DAC_DIGITAL_VOLUME_LEFT,
2263 WM8904_DAC_VU, WM8904_DAC_VU);
2264 regmap_update_bits(wm8904->regmap, WM8904_DAC_DIGITAL_VOLUME_RIGHT,
2265 WM8904_DAC_VU, WM8904_DAC_VU);
2266 regmap_update_bits(wm8904->regmap, WM8904_ANALOGUE_OUT1_LEFT,
2267 WM8904_HPOUT_VU | WM8904_HPOUTLZC,
2268 WM8904_HPOUT_VU | WM8904_HPOUTLZC);
2269 regmap_update_bits(wm8904->regmap, WM8904_ANALOGUE_OUT1_RIGHT,
2270 WM8904_HPOUT_VU | WM8904_HPOUTRZC,
2271 WM8904_HPOUT_VU | WM8904_HPOUTRZC);
2272 regmap_update_bits(wm8904->regmap, WM8904_ANALOGUE_OUT2_LEFT,
2273 WM8904_LINEOUT_VU | WM8904_LINEOUTLZC,
2274 WM8904_LINEOUT_VU | WM8904_LINEOUTLZC);
2275 regmap_update_bits(wm8904->regmap, WM8904_ANALOGUE_OUT2_RIGHT,
2276 WM8904_LINEOUT_VU | WM8904_LINEOUTRZC,
2277 WM8904_LINEOUT_VU | WM8904_LINEOUTRZC);
2278 regmap_update_bits(wm8904->regmap, WM8904_CLOCK_RATES_0,
2279 WM8904_SR_MODE, 0);
2280
2281 /* Apply configuration from the platform data. */
2282 if (wm8904->pdata) {
2283 for (i = 0; i < WM8904_GPIO_REGS; i++) {
2284 if (!wm8904->pdata->gpio_cfg[i])
2285 continue;
2286
2287 regmap_update_bits(wm8904->regmap,
2288 WM8904_GPIO_CONTROL_1 + i,
2289 0xffff,
2290 wm8904->pdata->gpio_cfg[i]);
2291 }
2292
2293 /* Zero is the default value for these anyway */
2294 for (i = 0; i < WM8904_MIC_REGS; i++)
2295 regmap_update_bits(wm8904->regmap,
2296 WM8904_MIC_BIAS_CONTROL_0 + i,
2297 0xffff,
2298 wm8904->pdata->mic_cfg[i]);
2299 }
2300
2301 /* Set Class W by default - this will be managed by the Class
2302 * G widget at runtime where bypass paths are available.
2303 */
2304 regmap_update_bits(wm8904->regmap, WM8904_CLASS_W_0,
2305 WM8904_CP_DYN_PWR, WM8904_CP_DYN_PWR);
2306
2307 /* Use normal bias source */
2308 regmap_update_bits(wm8904->regmap, WM8904_BIAS_CONTROL_0,
2309 WM8904_POBCTRL, 0);
2310
2311 /* Fill the cache for the ADC test register */
2312 regmap_read(wm8904->regmap, WM8904_ADC_TEST_0, &val);
2313
2314 /* Can leave the device powered off until we need it */
2315 regcache_cache_only(wm8904->regmap, true);
2316 regulator_bulk_disable(ARRAY_SIZE(wm8904->supplies), wm8904->supplies);
2317
2318 ret = devm_snd_soc_register_component(&i2c->dev,
2319 &soc_component_dev_wm8904, &wm8904_dai, 1);
2320 if (ret != 0)
2321 return ret;
2322
2323 return 0;
2324
2325 err_enable:
2326 regulator_bulk_disable(ARRAY_SIZE(wm8904->supplies), wm8904->supplies);
2327 return ret;
2328 }
2329
2330 static const struct i2c_device_id wm8904_i2c_id[] = {
2331 { "wm8904", WM8904 },
2332 { "wm8912", WM8912 },
2333 { "wm8918", WM8904 }, /* Actually a subset, updates to follow */
2334 { }
2335 };
2336 MODULE_DEVICE_TABLE(i2c, wm8904_i2c_id);
2337
2338 static struct i2c_driver wm8904_i2c_driver = {
2339 .driver = {
2340 .name = "wm8904",
2341 .of_match_table = of_match_ptr(wm8904_of_match),
2342 },
2343 .probe = wm8904_i2c_probe,
2344 .id_table = wm8904_i2c_id,
2345 };
2346
2347 module_i2c_driver(wm8904_i2c_driver);
2348
2349 MODULE_DESCRIPTION("ASoC WM8904 driver");
2350 MODULE_AUTHOR("Mark Brown <broonie@opensource.wolfsonmicro.com>");
2351 MODULE_LICENSE("GPL");
2352