1 /* 2 * ALSA SoC I2S Audio Layer for Broadcom BCM2835 SoC 3 * 4 * Author: Florian Meier <florian.meier@koalo.de> 5 * Copyright 2013 6 * 7 * Based on 8 * Raspberry Pi PCM I2S ALSA Driver 9 * Copyright (c) by Phil Poole 2013 10 * 11 * ALSA SoC I2S (McBSP) Audio Layer for TI DAVINCI processor 12 * Vladimir Barinov, <vbarinov@embeddedalley.com> 13 * Copyright (C) 2007 MontaVista Software, Inc., <source@mvista.com> 14 * 15 * OMAP ALSA SoC DAI driver using McBSP port 16 * Copyright (C) 2008 Nokia Corporation 17 * Contact: Jarkko Nikula <jarkko.nikula@bitmer.com> 18 * Peter Ujfalusi <peter.ujfalusi@ti.com> 19 * 20 * Freescale SSI ALSA SoC Digital Audio Interface (DAI) driver 21 * Author: Timur Tabi <timur@freescale.com> 22 * Copyright 2007-2010 Freescale Semiconductor, Inc. 23 * 24 * This program is free software; you can redistribute it and/or 25 * modify it under the terms of the GNU General Public License 26 * version 2 as published by the Free Software Foundation. 27 * 28 * This program is distributed in the hope that it will be useful, but 29 * WITHOUT ANY WARRANTY; without even the implied warranty of 30 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU 31 * General Public License for more details. 32 */ 33 34 #include <linux/init.h> 35 #include <linux/module.h> 36 #include <linux/device.h> 37 #include <linux/slab.h> 38 #include <linux/delay.h> 39 #include <linux/io.h> 40 #include <linux/clk.h> 41 42 #include <sound/core.h> 43 #include <sound/pcm.h> 44 #include <sound/pcm_params.h> 45 #include <sound/initval.h> 46 #include <sound/soc.h> 47 #include <sound/dmaengine_pcm.h> 48 49 /* Clock registers */ 50 #define BCM2835_CLK_PCMCTL_REG 0x00 51 #define BCM2835_CLK_PCMDIV_REG 0x04 52 53 /* Clock register settings */ 54 #define BCM2835_CLK_PASSWD (0x5a000000) 55 #define BCM2835_CLK_PASSWD_MASK (0xff000000) 56 #define BCM2835_CLK_MASH(v) ((v) << 9) 57 #define BCM2835_CLK_FLIP BIT(8) 58 #define BCM2835_CLK_BUSY BIT(7) 59 #define BCM2835_CLK_KILL BIT(5) 60 #define BCM2835_CLK_ENAB BIT(4) 61 #define BCM2835_CLK_SRC(v) (v) 62 63 #define BCM2835_CLK_SHIFT (12) 64 #define BCM2835_CLK_DIVI(v) ((v) << BCM2835_CLK_SHIFT) 65 #define BCM2835_CLK_DIVF(v) (v) 66 #define BCM2835_CLK_DIVF_MASK (0xFFF) 67 68 enum { 69 BCM2835_CLK_MASH_0 = 0, 70 BCM2835_CLK_MASH_1, 71 BCM2835_CLK_MASH_2, 72 BCM2835_CLK_MASH_3, 73 }; 74 75 enum { 76 BCM2835_CLK_SRC_GND = 0, 77 BCM2835_CLK_SRC_OSC, 78 BCM2835_CLK_SRC_DBG0, 79 BCM2835_CLK_SRC_DBG1, 80 BCM2835_CLK_SRC_PLLA, 81 BCM2835_CLK_SRC_PLLC, 82 BCM2835_CLK_SRC_PLLD, 83 BCM2835_CLK_SRC_HDMI, 84 }; 85 86 /* Most clocks are not useable (freq = 0) */ 87 static const unsigned int bcm2835_clk_freq[BCM2835_CLK_SRC_HDMI+1] = { 88 [BCM2835_CLK_SRC_GND] = 0, 89 [BCM2835_CLK_SRC_OSC] = 19200000, 90 [BCM2835_CLK_SRC_DBG0] = 0, 91 [BCM2835_CLK_SRC_DBG1] = 0, 92 [BCM2835_CLK_SRC_PLLA] = 0, 93 [BCM2835_CLK_SRC_PLLC] = 0, 94 [BCM2835_CLK_SRC_PLLD] = 500000000, 95 [BCM2835_CLK_SRC_HDMI] = 0, 96 }; 97 98 /* I2S registers */ 99 #define BCM2835_I2S_CS_A_REG 0x00 100 #define BCM2835_I2S_FIFO_A_REG 0x04 101 #define BCM2835_I2S_MODE_A_REG 0x08 102 #define BCM2835_I2S_RXC_A_REG 0x0c 103 #define BCM2835_I2S_TXC_A_REG 0x10 104 #define BCM2835_I2S_DREQ_A_REG 0x14 105 #define BCM2835_I2S_INTEN_A_REG 0x18 106 #define BCM2835_I2S_INTSTC_A_REG 0x1c 107 #define BCM2835_I2S_GRAY_REG 0x20 108 109 /* I2S register settings */ 110 #define BCM2835_I2S_STBY BIT(25) 111 #define BCM2835_I2S_SYNC BIT(24) 112 #define BCM2835_I2S_RXSEX BIT(23) 113 #define BCM2835_I2S_RXF BIT(22) 114 #define BCM2835_I2S_TXE BIT(21) 115 #define BCM2835_I2S_RXD BIT(20) 116 #define BCM2835_I2S_TXD BIT(19) 117 #define BCM2835_I2S_RXR BIT(18) 118 #define BCM2835_I2S_TXW BIT(17) 119 #define BCM2835_I2S_CS_RXERR BIT(16) 120 #define BCM2835_I2S_CS_TXERR BIT(15) 121 #define BCM2835_I2S_RXSYNC BIT(14) 122 #define BCM2835_I2S_TXSYNC BIT(13) 123 #define BCM2835_I2S_DMAEN BIT(9) 124 #define BCM2835_I2S_RXTHR(v) ((v) << 7) 125 #define BCM2835_I2S_TXTHR(v) ((v) << 5) 126 #define BCM2835_I2S_RXCLR BIT(4) 127 #define BCM2835_I2S_TXCLR BIT(3) 128 #define BCM2835_I2S_TXON BIT(2) 129 #define BCM2835_I2S_RXON BIT(1) 130 #define BCM2835_I2S_EN (1) 131 132 #define BCM2835_I2S_CLKDIS BIT(28) 133 #define BCM2835_I2S_PDMN BIT(27) 134 #define BCM2835_I2S_PDME BIT(26) 135 #define BCM2835_I2S_FRXP BIT(25) 136 #define BCM2835_I2S_FTXP BIT(24) 137 #define BCM2835_I2S_CLKM BIT(23) 138 #define BCM2835_I2S_CLKI BIT(22) 139 #define BCM2835_I2S_FSM BIT(21) 140 #define BCM2835_I2S_FSI BIT(20) 141 #define BCM2835_I2S_FLEN(v) ((v) << 10) 142 #define BCM2835_I2S_FSLEN(v) (v) 143 144 #define BCM2835_I2S_CHWEX BIT(15) 145 #define BCM2835_I2S_CHEN BIT(14) 146 #define BCM2835_I2S_CHPOS(v) ((v) << 4) 147 #define BCM2835_I2S_CHWID(v) (v) 148 #define BCM2835_I2S_CH1(v) ((v) << 16) 149 #define BCM2835_I2S_CH2(v) (v) 150 151 #define BCM2835_I2S_TX_PANIC(v) ((v) << 24) 152 #define BCM2835_I2S_RX_PANIC(v) ((v) << 16) 153 #define BCM2835_I2S_TX(v) ((v) << 8) 154 #define BCM2835_I2S_RX(v) (v) 155 156 #define BCM2835_I2S_INT_RXERR BIT(3) 157 #define BCM2835_I2S_INT_TXERR BIT(2) 158 #define BCM2835_I2S_INT_RXR BIT(1) 159 #define BCM2835_I2S_INT_TXW BIT(0) 160 161 /* I2S DMA interface */ 162 /* FIXME: Needs IOMMU support */ 163 #define BCM2835_VCMMU_SHIFT (0x7E000000 - 0x20000000) 164 165 /* General device struct */ 166 struct bcm2835_i2s_dev { 167 struct device *dev; 168 struct snd_dmaengine_dai_dma_data dma_data[2]; 169 unsigned int fmt; 170 unsigned int bclk_ratio; 171 172 struct regmap *i2s_regmap; 173 struct regmap *clk_regmap; 174 }; 175 176 static void bcm2835_i2s_start_clock(struct bcm2835_i2s_dev *dev) 177 { 178 /* Start the clock if in master mode */ 179 unsigned int master = dev->fmt & SND_SOC_DAIFMT_MASTER_MASK; 180 181 switch (master) { 182 case SND_SOC_DAIFMT_CBS_CFS: 183 case SND_SOC_DAIFMT_CBS_CFM: 184 regmap_update_bits(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, 185 BCM2835_CLK_PASSWD_MASK | BCM2835_CLK_ENAB, 186 BCM2835_CLK_PASSWD | BCM2835_CLK_ENAB); 187 break; 188 default: 189 break; 190 } 191 } 192 193 static void bcm2835_i2s_stop_clock(struct bcm2835_i2s_dev *dev) 194 { 195 uint32_t clkreg; 196 int timeout = 1000; 197 198 /* Stop clock */ 199 regmap_update_bits(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, 200 BCM2835_CLK_PASSWD_MASK | BCM2835_CLK_ENAB, 201 BCM2835_CLK_PASSWD); 202 203 /* Wait for the BUSY flag going down */ 204 while (--timeout) { 205 regmap_read(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, &clkreg); 206 if (!(clkreg & BCM2835_CLK_BUSY)) 207 break; 208 } 209 210 if (!timeout) { 211 /* KILL the clock */ 212 dev_err(dev->dev, "I2S clock didn't stop. Kill the clock!\n"); 213 regmap_update_bits(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, 214 BCM2835_CLK_KILL | BCM2835_CLK_PASSWD_MASK, 215 BCM2835_CLK_KILL | BCM2835_CLK_PASSWD); 216 } 217 } 218 219 static void bcm2835_i2s_clear_fifos(struct bcm2835_i2s_dev *dev, 220 bool tx, bool rx) 221 { 222 int timeout = 1000; 223 uint32_t syncval; 224 uint32_t csreg; 225 uint32_t i2s_active_state; 226 uint32_t clkreg; 227 uint32_t clk_active_state; 228 uint32_t off; 229 uint32_t clr; 230 231 off = tx ? BCM2835_I2S_TXON : 0; 232 off |= rx ? BCM2835_I2S_RXON : 0; 233 234 clr = tx ? BCM2835_I2S_TXCLR : 0; 235 clr |= rx ? BCM2835_I2S_RXCLR : 0; 236 237 /* Backup the current state */ 238 regmap_read(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, &csreg); 239 i2s_active_state = csreg & (BCM2835_I2S_RXON | BCM2835_I2S_TXON); 240 241 regmap_read(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, &clkreg); 242 clk_active_state = clkreg & BCM2835_CLK_ENAB; 243 244 /* Start clock if not running */ 245 if (!clk_active_state) { 246 regmap_update_bits(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, 247 BCM2835_CLK_PASSWD_MASK | BCM2835_CLK_ENAB, 248 BCM2835_CLK_PASSWD | BCM2835_CLK_ENAB); 249 } 250 251 /* Stop I2S module */ 252 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, off, 0); 253 254 /* 255 * Clear the FIFOs 256 * Requires at least 2 PCM clock cycles to take effect 257 */ 258 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, clr, clr); 259 260 /* Wait for 2 PCM clock cycles */ 261 262 /* 263 * Toggle the SYNC flag. After 2 PCM clock cycles it can be read back 264 * FIXME: This does not seem to work for slave mode! 265 */ 266 regmap_read(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, &syncval); 267 syncval &= BCM2835_I2S_SYNC; 268 269 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, 270 BCM2835_I2S_SYNC, ~syncval); 271 272 /* Wait for the SYNC flag changing it's state */ 273 while (--timeout) { 274 regmap_read(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, &csreg); 275 if ((csreg & BCM2835_I2S_SYNC) != syncval) 276 break; 277 } 278 279 if (!timeout) 280 dev_err(dev->dev, "I2S SYNC error!\n"); 281 282 /* Stop clock if it was not running before */ 283 if (!clk_active_state) 284 bcm2835_i2s_stop_clock(dev); 285 286 /* Restore I2S state */ 287 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, 288 BCM2835_I2S_RXON | BCM2835_I2S_TXON, i2s_active_state); 289 } 290 291 static int bcm2835_i2s_set_dai_fmt(struct snd_soc_dai *dai, 292 unsigned int fmt) 293 { 294 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 295 dev->fmt = fmt; 296 return 0; 297 } 298 299 static int bcm2835_i2s_set_dai_bclk_ratio(struct snd_soc_dai *dai, 300 unsigned int ratio) 301 { 302 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 303 dev->bclk_ratio = ratio; 304 return 0; 305 } 306 307 static int bcm2835_i2s_hw_params(struct snd_pcm_substream *substream, 308 struct snd_pcm_hw_params *params, 309 struct snd_soc_dai *dai) 310 { 311 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 312 313 unsigned int sampling_rate = params_rate(params); 314 unsigned int data_length, data_delay, bclk_ratio; 315 unsigned int ch1pos, ch2pos, mode, format; 316 unsigned int mash = BCM2835_CLK_MASH_1; 317 unsigned int divi, divf, target_frequency; 318 int clk_src = -1; 319 unsigned int master = dev->fmt & SND_SOC_DAIFMT_MASTER_MASK; 320 bool bit_master = (master == SND_SOC_DAIFMT_CBS_CFS 321 || master == SND_SOC_DAIFMT_CBS_CFM); 322 323 bool frame_master = (master == SND_SOC_DAIFMT_CBS_CFS 324 || master == SND_SOC_DAIFMT_CBM_CFS); 325 uint32_t csreg; 326 327 /* 328 * If a stream is already enabled, 329 * the registers are already set properly. 330 */ 331 regmap_read(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, &csreg); 332 333 if (csreg & (BCM2835_I2S_TXON | BCM2835_I2S_RXON)) 334 return 0; 335 336 /* 337 * Adjust the data length according to the format. 338 * We prefill the half frame length with an integer 339 * divider of 2400 as explained at the clock settings. 340 * Maybe it is overwritten there, if the Integer mode 341 * does not apply. 342 */ 343 switch (params_format(params)) { 344 case SNDRV_PCM_FORMAT_S16_LE: 345 data_length = 16; 346 bclk_ratio = 40; 347 break; 348 case SNDRV_PCM_FORMAT_S32_LE: 349 data_length = 32; 350 bclk_ratio = 80; 351 break; 352 default: 353 return -EINVAL; 354 } 355 356 /* If bclk_ratio already set, use that one. */ 357 if (dev->bclk_ratio) 358 bclk_ratio = dev->bclk_ratio; 359 360 /* 361 * Clock Settings 362 * 363 * The target frequency of the bit clock is 364 * sampling rate * frame length 365 * 366 * Integer mode: 367 * Sampling rates that are multiples of 8000 kHz 368 * can be driven by the oscillator of 19.2 MHz 369 * with an integer divider as long as the frame length 370 * is an integer divider of 19200000/8000=2400 as set up above. 371 * This is no longer possible if the sampling rate 372 * is too high (e.g. 192 kHz), because the oscillator is too slow. 373 * 374 * MASH mode: 375 * For all other sampling rates, it is not possible to 376 * have an integer divider. Approximate the clock 377 * with the MASH module that induces a slight frequency 378 * variance. To minimize that it is best to have the fastest 379 * clock here. That is PLLD with 500 MHz. 380 */ 381 target_frequency = sampling_rate * bclk_ratio; 382 clk_src = BCM2835_CLK_SRC_OSC; 383 mash = BCM2835_CLK_MASH_0; 384 385 if (bcm2835_clk_freq[clk_src] % target_frequency == 0 386 && bit_master && frame_master) { 387 divi = bcm2835_clk_freq[clk_src] / target_frequency; 388 divf = 0; 389 } else { 390 uint64_t dividend; 391 392 if (!dev->bclk_ratio) { 393 /* 394 * Overwrite bclk_ratio, because the 395 * above trick is not needed or can 396 * not be used. 397 */ 398 bclk_ratio = 2 * data_length; 399 } 400 401 target_frequency = sampling_rate * bclk_ratio; 402 403 clk_src = BCM2835_CLK_SRC_PLLD; 404 mash = BCM2835_CLK_MASH_1; 405 406 dividend = bcm2835_clk_freq[clk_src]; 407 dividend <<= BCM2835_CLK_SHIFT; 408 do_div(dividend, target_frequency); 409 divi = dividend >> BCM2835_CLK_SHIFT; 410 divf = dividend & BCM2835_CLK_DIVF_MASK; 411 } 412 413 /* Set clock divider */ 414 regmap_write(dev->clk_regmap, BCM2835_CLK_PCMDIV_REG, BCM2835_CLK_PASSWD 415 | BCM2835_CLK_DIVI(divi) 416 | BCM2835_CLK_DIVF(divf)); 417 418 /* Setup clock, but don't start it yet */ 419 regmap_write(dev->clk_regmap, BCM2835_CLK_PCMCTL_REG, BCM2835_CLK_PASSWD 420 | BCM2835_CLK_MASH(mash) 421 | BCM2835_CLK_SRC(clk_src)); 422 423 /* Setup the frame format */ 424 format = BCM2835_I2S_CHEN; 425 426 if (data_length > 24) 427 format |= BCM2835_I2S_CHWEX; 428 429 format |= BCM2835_I2S_CHWID((data_length-8)&0xf); 430 431 switch (dev->fmt & SND_SOC_DAIFMT_FORMAT_MASK) { 432 case SND_SOC_DAIFMT_I2S: 433 data_delay = 1; 434 break; 435 default: 436 /* 437 * TODO 438 * Others are possible but are not implemented at the moment. 439 */ 440 dev_err(dev->dev, "%s:bad format\n", __func__); 441 return -EINVAL; 442 } 443 444 ch1pos = data_delay; 445 ch2pos = bclk_ratio / 2 + data_delay; 446 447 switch (params_channels(params)) { 448 case 2: 449 format = BCM2835_I2S_CH1(format) | BCM2835_I2S_CH2(format); 450 format |= BCM2835_I2S_CH1(BCM2835_I2S_CHPOS(ch1pos)); 451 format |= BCM2835_I2S_CH2(BCM2835_I2S_CHPOS(ch2pos)); 452 break; 453 default: 454 return -EINVAL; 455 } 456 457 /* 458 * Set format for both streams. 459 * We cannot set another frame length 460 * (and therefore word length) anyway, 461 * so the format will be the same. 462 */ 463 regmap_write(dev->i2s_regmap, BCM2835_I2S_RXC_A_REG, format); 464 regmap_write(dev->i2s_regmap, BCM2835_I2S_TXC_A_REG, format); 465 466 /* Setup the I2S mode */ 467 mode = 0; 468 469 if (data_length <= 16) { 470 /* 471 * Use frame packed mode (2 channels per 32 bit word) 472 * We cannot set another frame length in the second stream 473 * (and therefore word length) anyway, 474 * so the format will be the same. 475 */ 476 mode |= BCM2835_I2S_FTXP | BCM2835_I2S_FRXP; 477 } 478 479 mode |= BCM2835_I2S_FLEN(bclk_ratio - 1); 480 mode |= BCM2835_I2S_FSLEN(bclk_ratio / 2); 481 482 /* Master or slave? */ 483 switch (dev->fmt & SND_SOC_DAIFMT_MASTER_MASK) { 484 case SND_SOC_DAIFMT_CBS_CFS: 485 /* CPU is master */ 486 break; 487 case SND_SOC_DAIFMT_CBM_CFS: 488 /* 489 * CODEC is bit clock master 490 * CPU is frame master 491 */ 492 mode |= BCM2835_I2S_CLKM; 493 break; 494 case SND_SOC_DAIFMT_CBS_CFM: 495 /* 496 * CODEC is frame master 497 * CPU is bit clock master 498 */ 499 mode |= BCM2835_I2S_FSM; 500 break; 501 case SND_SOC_DAIFMT_CBM_CFM: 502 /* CODEC is master */ 503 mode |= BCM2835_I2S_CLKM; 504 mode |= BCM2835_I2S_FSM; 505 break; 506 default: 507 dev_err(dev->dev, "%s:bad master\n", __func__); 508 return -EINVAL; 509 } 510 511 /* 512 * Invert clocks? 513 * 514 * The BCM approach seems to be inverted to the classical I2S approach. 515 */ 516 switch (dev->fmt & SND_SOC_DAIFMT_INV_MASK) { 517 case SND_SOC_DAIFMT_NB_NF: 518 /* None. Therefore, both for BCM */ 519 mode |= BCM2835_I2S_CLKI; 520 mode |= BCM2835_I2S_FSI; 521 break; 522 case SND_SOC_DAIFMT_IB_IF: 523 /* Both. Therefore, none for BCM */ 524 break; 525 case SND_SOC_DAIFMT_NB_IF: 526 /* 527 * Invert only frame sync. Therefore, 528 * invert only bit clock for BCM 529 */ 530 mode |= BCM2835_I2S_CLKI; 531 break; 532 case SND_SOC_DAIFMT_IB_NF: 533 /* 534 * Invert only bit clock. Therefore, 535 * invert only frame sync for BCM 536 */ 537 mode |= BCM2835_I2S_FSI; 538 break; 539 default: 540 return -EINVAL; 541 } 542 543 regmap_write(dev->i2s_regmap, BCM2835_I2S_MODE_A_REG, mode); 544 545 /* Setup the DMA parameters */ 546 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, 547 BCM2835_I2S_RXTHR(1) 548 | BCM2835_I2S_TXTHR(1) 549 | BCM2835_I2S_DMAEN, 0xffffffff); 550 551 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_DREQ_A_REG, 552 BCM2835_I2S_TX_PANIC(0x10) 553 | BCM2835_I2S_RX_PANIC(0x30) 554 | BCM2835_I2S_TX(0x30) 555 | BCM2835_I2S_RX(0x20), 0xffffffff); 556 557 /* Clear FIFOs */ 558 bcm2835_i2s_clear_fifos(dev, true, true); 559 560 return 0; 561 } 562 563 static int bcm2835_i2s_prepare(struct snd_pcm_substream *substream, 564 struct snd_soc_dai *dai) 565 { 566 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 567 uint32_t cs_reg; 568 569 bcm2835_i2s_start_clock(dev); 570 571 /* 572 * Clear both FIFOs if the one that should be started 573 * is not empty at the moment. This should only happen 574 * after overrun. Otherwise, hw_params would have cleared 575 * the FIFO. 576 */ 577 regmap_read(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, &cs_reg); 578 579 if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK 580 && !(cs_reg & BCM2835_I2S_TXE)) 581 bcm2835_i2s_clear_fifos(dev, true, false); 582 else if (substream->stream == SNDRV_PCM_STREAM_CAPTURE 583 && (cs_reg & BCM2835_I2S_RXD)) 584 bcm2835_i2s_clear_fifos(dev, false, true); 585 586 return 0; 587 } 588 589 static void bcm2835_i2s_stop(struct bcm2835_i2s_dev *dev, 590 struct snd_pcm_substream *substream, 591 struct snd_soc_dai *dai) 592 { 593 uint32_t mask; 594 595 if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) 596 mask = BCM2835_I2S_RXON; 597 else 598 mask = BCM2835_I2S_TXON; 599 600 regmap_update_bits(dev->i2s_regmap, 601 BCM2835_I2S_CS_A_REG, mask, 0); 602 603 /* Stop also the clock when not SND_SOC_DAIFMT_CONT */ 604 if (!dai->active && !(dev->fmt & SND_SOC_DAIFMT_CONT)) 605 bcm2835_i2s_stop_clock(dev); 606 } 607 608 static int bcm2835_i2s_trigger(struct snd_pcm_substream *substream, int cmd, 609 struct snd_soc_dai *dai) 610 { 611 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 612 uint32_t mask; 613 614 switch (cmd) { 615 case SNDRV_PCM_TRIGGER_START: 616 case SNDRV_PCM_TRIGGER_RESUME: 617 case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: 618 bcm2835_i2s_start_clock(dev); 619 620 if (substream->stream == SNDRV_PCM_STREAM_CAPTURE) 621 mask = BCM2835_I2S_RXON; 622 else 623 mask = BCM2835_I2S_TXON; 624 625 regmap_update_bits(dev->i2s_regmap, 626 BCM2835_I2S_CS_A_REG, mask, mask); 627 break; 628 629 case SNDRV_PCM_TRIGGER_STOP: 630 case SNDRV_PCM_TRIGGER_SUSPEND: 631 case SNDRV_PCM_TRIGGER_PAUSE_PUSH: 632 bcm2835_i2s_stop(dev, substream, dai); 633 break; 634 default: 635 return -EINVAL; 636 } 637 638 return 0; 639 } 640 641 static int bcm2835_i2s_startup(struct snd_pcm_substream *substream, 642 struct snd_soc_dai *dai) 643 { 644 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 645 646 if (dai->active) 647 return 0; 648 649 /* Should this still be running stop it */ 650 bcm2835_i2s_stop_clock(dev); 651 652 /* Enable PCM block */ 653 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, 654 BCM2835_I2S_EN, BCM2835_I2S_EN); 655 656 /* 657 * Disable STBY. 658 * Requires at least 4 PCM clock cycles to take effect. 659 */ 660 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, 661 BCM2835_I2S_STBY, BCM2835_I2S_STBY); 662 663 return 0; 664 } 665 666 static void bcm2835_i2s_shutdown(struct snd_pcm_substream *substream, 667 struct snd_soc_dai *dai) 668 { 669 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 670 671 bcm2835_i2s_stop(dev, substream, dai); 672 673 /* If both streams are stopped, disable module and clock */ 674 if (dai->active) 675 return; 676 677 /* Disable the module */ 678 regmap_update_bits(dev->i2s_regmap, BCM2835_I2S_CS_A_REG, 679 BCM2835_I2S_EN, 0); 680 681 /* 682 * Stopping clock is necessary, because stop does 683 * not stop the clock when SND_SOC_DAIFMT_CONT 684 */ 685 bcm2835_i2s_stop_clock(dev); 686 } 687 688 static const struct snd_soc_dai_ops bcm2835_i2s_dai_ops = { 689 .startup = bcm2835_i2s_startup, 690 .shutdown = bcm2835_i2s_shutdown, 691 .prepare = bcm2835_i2s_prepare, 692 .trigger = bcm2835_i2s_trigger, 693 .hw_params = bcm2835_i2s_hw_params, 694 .set_fmt = bcm2835_i2s_set_dai_fmt, 695 .set_bclk_ratio = bcm2835_i2s_set_dai_bclk_ratio 696 }; 697 698 static int bcm2835_i2s_dai_probe(struct snd_soc_dai *dai) 699 { 700 struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai); 701 702 snd_soc_dai_init_dma_data(dai, 703 &dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK], 704 &dev->dma_data[SNDRV_PCM_STREAM_CAPTURE]); 705 706 return 0; 707 } 708 709 static struct snd_soc_dai_driver bcm2835_i2s_dai = { 710 .name = "bcm2835-i2s", 711 .probe = bcm2835_i2s_dai_probe, 712 .playback = { 713 .channels_min = 2, 714 .channels_max = 2, 715 .rates = SNDRV_PCM_RATE_8000_192000, 716 .formats = SNDRV_PCM_FMTBIT_S16_LE 717 | SNDRV_PCM_FMTBIT_S32_LE 718 }, 719 .capture = { 720 .channels_min = 2, 721 .channels_max = 2, 722 .rates = SNDRV_PCM_RATE_8000_192000, 723 .formats = SNDRV_PCM_FMTBIT_S16_LE 724 | SNDRV_PCM_FMTBIT_S32_LE 725 }, 726 .ops = &bcm2835_i2s_dai_ops, 727 .symmetric_rates = 1 728 }; 729 730 static bool bcm2835_i2s_volatile_reg(struct device *dev, unsigned int reg) 731 { 732 switch (reg) { 733 case BCM2835_I2S_CS_A_REG: 734 case BCM2835_I2S_FIFO_A_REG: 735 case BCM2835_I2S_INTSTC_A_REG: 736 case BCM2835_I2S_GRAY_REG: 737 return true; 738 default: 739 return false; 740 }; 741 } 742 743 static bool bcm2835_i2s_precious_reg(struct device *dev, unsigned int reg) 744 { 745 switch (reg) { 746 case BCM2835_I2S_FIFO_A_REG: 747 return true; 748 default: 749 return false; 750 }; 751 } 752 753 static bool bcm2835_clk_volatile_reg(struct device *dev, unsigned int reg) 754 { 755 switch (reg) { 756 case BCM2835_CLK_PCMCTL_REG: 757 return true; 758 default: 759 return false; 760 }; 761 } 762 763 static const struct regmap_config bcm2835_regmap_config[] = { 764 { 765 .reg_bits = 32, 766 .reg_stride = 4, 767 .val_bits = 32, 768 .max_register = BCM2835_I2S_GRAY_REG, 769 .precious_reg = bcm2835_i2s_precious_reg, 770 .volatile_reg = bcm2835_i2s_volatile_reg, 771 .cache_type = REGCACHE_RBTREE, 772 }, 773 { 774 .reg_bits = 32, 775 .reg_stride = 4, 776 .val_bits = 32, 777 .max_register = BCM2835_CLK_PCMDIV_REG, 778 .volatile_reg = bcm2835_clk_volatile_reg, 779 .cache_type = REGCACHE_RBTREE, 780 }, 781 }; 782 783 static const struct snd_soc_component_driver bcm2835_i2s_component = { 784 .name = "bcm2835-i2s-comp", 785 }; 786 787 static int bcm2835_i2s_probe(struct platform_device *pdev) 788 { 789 struct bcm2835_i2s_dev *dev; 790 int i; 791 int ret; 792 struct regmap *regmap[2]; 793 struct resource *mem[2]; 794 795 /* Request both ioareas */ 796 for (i = 0; i <= 1; i++) { 797 void __iomem *base; 798 799 mem[i] = platform_get_resource(pdev, IORESOURCE_MEM, i); 800 base = devm_ioremap_resource(&pdev->dev, mem[i]); 801 if (IS_ERR(base)) 802 return PTR_ERR(base); 803 804 regmap[i] = devm_regmap_init_mmio(&pdev->dev, base, 805 &bcm2835_regmap_config[i]); 806 if (IS_ERR(regmap[i])) 807 return PTR_ERR(regmap[i]); 808 } 809 810 dev = devm_kzalloc(&pdev->dev, sizeof(*dev), 811 GFP_KERNEL); 812 if (!dev) 813 return -ENOMEM; 814 815 dev->i2s_regmap = regmap[0]; 816 dev->clk_regmap = regmap[1]; 817 818 /* Set the DMA address */ 819 dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].addr = 820 (dma_addr_t)mem[0]->start + BCM2835_I2S_FIFO_A_REG 821 + BCM2835_VCMMU_SHIFT; 822 823 dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].addr = 824 (dma_addr_t)mem[0]->start + BCM2835_I2S_FIFO_A_REG 825 + BCM2835_VCMMU_SHIFT; 826 827 /* Set the bus width */ 828 dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].addr_width = 829 DMA_SLAVE_BUSWIDTH_4_BYTES; 830 dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].addr_width = 831 DMA_SLAVE_BUSWIDTH_4_BYTES; 832 833 /* Set burst */ 834 dev->dma_data[SNDRV_PCM_STREAM_PLAYBACK].maxburst = 2; 835 dev->dma_data[SNDRV_PCM_STREAM_CAPTURE].maxburst = 2; 836 837 /* BCLK ratio - use default */ 838 dev->bclk_ratio = 0; 839 840 /* Store the pdev */ 841 dev->dev = &pdev->dev; 842 dev_set_drvdata(&pdev->dev, dev); 843 844 ret = devm_snd_soc_register_component(&pdev->dev, 845 &bcm2835_i2s_component, &bcm2835_i2s_dai, 1); 846 if (ret) { 847 dev_err(&pdev->dev, "Could not register DAI: %d\n", ret); 848 return ret; 849 } 850 851 ret = devm_snd_dmaengine_pcm_register(&pdev->dev, NULL, 0); 852 if (ret) { 853 dev_err(&pdev->dev, "Could not register PCM: %d\n", ret); 854 return ret; 855 } 856 857 return 0; 858 } 859 860 static const struct of_device_id bcm2835_i2s_of_match[] = { 861 { .compatible = "brcm,bcm2835-i2s", }, 862 {}, 863 }; 864 865 static struct platform_driver bcm2835_i2s_driver = { 866 .probe = bcm2835_i2s_probe, 867 .driver = { 868 .name = "bcm2835-i2s", 869 .of_match_table = bcm2835_i2s_of_match, 870 }, 871 }; 872 873 module_platform_driver(bcm2835_i2s_driver); 874 875 MODULE_ALIAS("platform:bcm2835-i2s"); 876 MODULE_DESCRIPTION("BCM2835 I2S interface"); 877 MODULE_AUTHOR("Florian Meier <florian.meier@koalo.de>"); 878 MODULE_LICENSE("GPL v2"); 879