1 // SPDX-License-Identifier: GPL-2.0-only 2 /****************************************************************************** 3 4 AudioScience HPI driver 5 Copyright (C) 1997-2011 AudioScience Inc. <support@audioscience.com> 6 7 8 Hardware Programming Interface (HPI) for AudioScience ASI6200 series adapters. 9 These PCI bus adapters are based on the TI C6711 DSP. 10 11 Exported functions: 12 void HPI_6000(struct hpi_message *phm, struct hpi_response *phr) 13 14 #defines 15 HIDE_PCI_ASSERTS to show the PCI asserts 16 PROFILE_DSP2 get profile data from DSP2 if present (instead of DSP 1) 17 18 (C) Copyright AudioScience Inc. 1998-2003 19 *******************************************************************************/ 20 #define SOURCEFILE_NAME "hpi6000.c" 21 22 #include "hpi_internal.h" 23 #include "hpimsginit.h" 24 #include "hpidebug.h" 25 #include "hpi6000.h" 26 #include "hpidspcd.h" 27 #include "hpicmn.h" 28 29 #define HPI_HIF_BASE (0x00000200) /* start of C67xx internal RAM */ 30 #define HPI_HIF_ADDR(member) \ 31 (HPI_HIF_BASE + offsetof(struct hpi_hif_6000, member)) 32 #define HPI_HIF_ERROR_MASK 0x4000 33 34 /* HPI6000 specific error codes */ 35 #define HPI6000_ERROR_BASE 900 /* not actually used anywhere */ 36 37 /* operational/messaging errors */ 38 #define HPI6000_ERROR_MSG_RESP_IDLE_TIMEOUT 901 39 #define HPI6000_ERROR_RESP_GET_LEN 902 40 #define HPI6000_ERROR_MSG_RESP_GET_RESP_ACK 903 41 #define HPI6000_ERROR_MSG_GET_ADR 904 42 #define HPI6000_ERROR_RESP_GET_ADR 905 43 #define HPI6000_ERROR_MSG_RESP_BLOCKWRITE32 906 44 #define HPI6000_ERROR_MSG_RESP_BLOCKREAD32 907 45 46 #define HPI6000_ERROR_CONTROL_CACHE_PARAMS 909 47 48 #define HPI6000_ERROR_SEND_DATA_IDLE_TIMEOUT 911 49 #define HPI6000_ERROR_SEND_DATA_ACK 912 50 #define HPI6000_ERROR_SEND_DATA_ADR 913 51 #define HPI6000_ERROR_SEND_DATA_TIMEOUT 914 52 #define HPI6000_ERROR_SEND_DATA_CMD 915 53 #define HPI6000_ERROR_SEND_DATA_WRITE 916 54 #define HPI6000_ERROR_SEND_DATA_IDLECMD 917 55 56 #define HPI6000_ERROR_GET_DATA_IDLE_TIMEOUT 921 57 #define HPI6000_ERROR_GET_DATA_ACK 922 58 #define HPI6000_ERROR_GET_DATA_CMD 923 59 #define HPI6000_ERROR_GET_DATA_READ 924 60 #define HPI6000_ERROR_GET_DATA_IDLECMD 925 61 62 #define HPI6000_ERROR_CONTROL_CACHE_ADDRLEN 951 63 #define HPI6000_ERROR_CONTROL_CACHE_READ 952 64 #define HPI6000_ERROR_CONTROL_CACHE_FLUSH 953 65 66 #define HPI6000_ERROR_MSG_RESP_GETRESPCMD 961 67 #define HPI6000_ERROR_MSG_RESP_IDLECMD 962 68 69 /* Initialisation/bootload errors */ 70 #define HPI6000_ERROR_UNHANDLED_SUBSYS_ID 930 71 72 /* can't access PCI2040 */ 73 #define HPI6000_ERROR_INIT_PCI2040 931 74 /* can't access DSP HPI i/f */ 75 #define HPI6000_ERROR_INIT_DSPHPI 932 76 /* can't access internal DSP memory */ 77 #define HPI6000_ERROR_INIT_DSPINTMEM 933 78 /* can't access SDRAM - test#1 */ 79 #define HPI6000_ERROR_INIT_SDRAM1 934 80 /* can't access SDRAM - test#2 */ 81 #define HPI6000_ERROR_INIT_SDRAM2 935 82 83 #define HPI6000_ERROR_INIT_VERIFY 938 84 85 #define HPI6000_ERROR_INIT_NOACK 939 86 87 #define HPI6000_ERROR_INIT_PLDTEST1 941 88 #define HPI6000_ERROR_INIT_PLDTEST2 942 89 90 /* local defines */ 91 92 #define HIDE_PCI_ASSERTS 93 #define PROFILE_DSP2 94 95 /* for PCI2040 i/f chip */ 96 /* HPI CSR registers */ 97 /* word offsets from CSR base */ 98 /* use when io addresses defined as u32 * */ 99 100 #define INTERRUPT_EVENT_SET 0 101 #define INTERRUPT_EVENT_CLEAR 1 102 #define INTERRUPT_MASK_SET 2 103 #define INTERRUPT_MASK_CLEAR 3 104 #define HPI_ERROR_REPORT 4 105 #define HPI_RESET 5 106 #define HPI_DATA_WIDTH 6 107 108 #define MAX_DSPS 2 109 /* HPI registers, spaced 8K bytes = 2K words apart */ 110 #define DSP_SPACING 0x800 111 112 #define CONTROL 0x0000 113 #define ADDRESS 0x0200 114 #define DATA_AUTOINC 0x0400 115 #define DATA 0x0600 116 117 #define TIMEOUT 500000 118 119 struct dsp_obj { 120 __iomem u32 *prHPI_control; 121 __iomem u32 *prHPI_address; 122 __iomem u32 *prHPI_data; 123 __iomem u32 *prHPI_data_auto_inc; 124 char c_dsp_rev; /*A, B */ 125 u32 control_cache_address_on_dsp; 126 u32 control_cache_length_on_dsp; 127 struct hpi_adapter_obj *pa_parent_adapter; 128 }; 129 130 struct hpi_hw_obj { 131 __iomem u32 *dw2040_HPICSR; 132 __iomem u32 *dw2040_HPIDSP; 133 134 u16 num_dsp; 135 struct dsp_obj ado[MAX_DSPS]; 136 137 u32 message_buffer_address_on_dsp; 138 u32 response_buffer_address_on_dsp; 139 u32 pCI2040HPI_error_count; 140 141 struct hpi_control_cache_single control_cache[HPI_NMIXER_CONTROLS]; 142 struct hpi_control_cache *p_cache; 143 }; 144 145 static u16 hpi6000_dsp_block_write32(struct hpi_adapter_obj *pao, 146 u16 dsp_index, u32 hpi_address, u32 *source, u32 count); 147 static u16 hpi6000_dsp_block_read32(struct hpi_adapter_obj *pao, 148 u16 dsp_index, u32 hpi_address, u32 *dest, u32 count); 149 150 static short hpi6000_adapter_boot_load_dsp(struct hpi_adapter_obj *pao, 151 u32 *pos_error_code); 152 static short hpi6000_check_PCI2040_error_flag(struct hpi_adapter_obj *pao, 153 u16 read_or_write); 154 #define H6READ 1 155 #define H6WRITE 0 156 157 static short hpi6000_update_control_cache(struct hpi_adapter_obj *pao, 158 struct hpi_message *phm); 159 static short hpi6000_message_response_sequence(struct hpi_adapter_obj *pao, 160 u16 dsp_index, struct hpi_message *phm, struct hpi_response *phr); 161 162 static void hw_message(struct hpi_adapter_obj *pao, struct hpi_message *phm, 163 struct hpi_response *phr); 164 165 static short hpi6000_wait_dsp_ack(struct hpi_adapter_obj *pao, u16 dsp_index, 166 u32 ack_value); 167 168 static short hpi6000_send_host_command(struct hpi_adapter_obj *pao, 169 u16 dsp_index, u32 host_cmd); 170 171 static void hpi6000_send_dsp_interrupt(struct dsp_obj *pdo); 172 173 static short hpi6000_send_data(struct hpi_adapter_obj *pao, u16 dsp_index, 174 struct hpi_message *phm, struct hpi_response *phr); 175 176 static short hpi6000_get_data(struct hpi_adapter_obj *pao, u16 dsp_index, 177 struct hpi_message *phm, struct hpi_response *phr); 178 179 static void hpi_write_word(struct dsp_obj *pdo, u32 address, u32 data); 180 181 static u32 hpi_read_word(struct dsp_obj *pdo, u32 address); 182 183 static void hpi_write_block(struct dsp_obj *pdo, u32 address, u32 *pdata, 184 u32 length); 185 186 static void hpi_read_block(struct dsp_obj *pdo, u32 address, u32 *pdata, 187 u32 length); 188 189 static void subsys_create_adapter(struct hpi_message *phm, 190 struct hpi_response *phr); 191 192 static void adapter_delete(struct hpi_adapter_obj *pao, 193 struct hpi_message *phm, struct hpi_response *phr); 194 195 static void adapter_get_asserts(struct hpi_adapter_obj *pao, 196 struct hpi_message *phm, struct hpi_response *phr); 197 198 static short create_adapter_obj(struct hpi_adapter_obj *pao, 199 u32 *pos_error_code); 200 201 static void delete_adapter_obj(struct hpi_adapter_obj *pao); 202 203 /* local globals */ 204 205 static u16 gw_pci_read_asserts; /* used to count PCI2040 errors */ 206 static u16 gw_pci_write_asserts; /* used to count PCI2040 errors */ 207 208 static void subsys_message(struct hpi_message *phm, struct hpi_response *phr) 209 { 210 switch (phm->function) { 211 case HPI_SUBSYS_CREATE_ADAPTER: 212 subsys_create_adapter(phm, phr); 213 break; 214 default: 215 phr->error = HPI_ERROR_INVALID_FUNC; 216 break; 217 } 218 } 219 220 static void control_message(struct hpi_adapter_obj *pao, 221 struct hpi_message *phm, struct hpi_response *phr) 222 { 223 struct hpi_hw_obj *phw = pao->priv; 224 225 switch (phm->function) { 226 case HPI_CONTROL_GET_STATE: 227 if (pao->has_control_cache) { 228 u16 err; 229 err = hpi6000_update_control_cache(pao, phm); 230 231 if (err) { 232 if (err >= HPI_ERROR_BACKEND_BASE) { 233 phr->error = 234 HPI_ERROR_CONTROL_CACHING; 235 phr->specific_error = err; 236 } else { 237 phr->error = err; 238 } 239 break; 240 } 241 242 if (hpi_check_control_cache(phw->p_cache, phm, phr)) 243 break; 244 } 245 hw_message(pao, phm, phr); 246 break; 247 case HPI_CONTROL_SET_STATE: 248 hw_message(pao, phm, phr); 249 hpi_cmn_control_cache_sync_to_msg(phw->p_cache, phm, phr); 250 break; 251 252 case HPI_CONTROL_GET_INFO: 253 default: 254 hw_message(pao, phm, phr); 255 break; 256 } 257 } 258 259 static void adapter_message(struct hpi_adapter_obj *pao, 260 struct hpi_message *phm, struct hpi_response *phr) 261 { 262 switch (phm->function) { 263 case HPI_ADAPTER_GET_ASSERT: 264 adapter_get_asserts(pao, phm, phr); 265 break; 266 267 case HPI_ADAPTER_DELETE: 268 adapter_delete(pao, phm, phr); 269 break; 270 271 default: 272 hw_message(pao, phm, phr); 273 break; 274 } 275 } 276 277 static void outstream_message(struct hpi_adapter_obj *pao, 278 struct hpi_message *phm, struct hpi_response *phr) 279 { 280 switch (phm->function) { 281 case HPI_OSTREAM_HOSTBUFFER_ALLOC: 282 case HPI_OSTREAM_HOSTBUFFER_FREE: 283 /* Don't let these messages go to the HW function because 284 * they're called without locking the spinlock. 285 * For the HPI6000 adapters the HW would return 286 * HPI_ERROR_INVALID_FUNC anyway. 287 */ 288 phr->error = HPI_ERROR_INVALID_FUNC; 289 break; 290 default: 291 hw_message(pao, phm, phr); 292 return; 293 } 294 } 295 296 static void instream_message(struct hpi_adapter_obj *pao, 297 struct hpi_message *phm, struct hpi_response *phr) 298 { 299 300 switch (phm->function) { 301 case HPI_ISTREAM_HOSTBUFFER_ALLOC: 302 case HPI_ISTREAM_HOSTBUFFER_FREE: 303 /* Don't let these messages go to the HW function because 304 * they're called without locking the spinlock. 305 * For the HPI6000 adapters the HW would return 306 * HPI_ERROR_INVALID_FUNC anyway. 307 */ 308 phr->error = HPI_ERROR_INVALID_FUNC; 309 break; 310 default: 311 hw_message(pao, phm, phr); 312 return; 313 } 314 } 315 316 /************************************************************************/ 317 /** HPI_6000() 318 * Entry point from HPIMAN 319 * All calls to the HPI start here 320 */ 321 void HPI_6000(struct hpi_message *phm, struct hpi_response *phr) 322 { 323 struct hpi_adapter_obj *pao = NULL; 324 325 if (phm->object != HPI_OBJ_SUBSYSTEM) { 326 pao = hpi_find_adapter(phm->adapter_index); 327 if (!pao) { 328 hpi_init_response(phr, phm->object, phm->function, 329 HPI_ERROR_BAD_ADAPTER_NUMBER); 330 HPI_DEBUG_LOG(DEBUG, "invalid adapter index: %d \n", 331 phm->adapter_index); 332 return; 333 } 334 335 /* Don't even try to communicate with crashed DSP */ 336 if (pao->dsp_crashed >= 10) { 337 hpi_init_response(phr, phm->object, phm->function, 338 HPI_ERROR_DSP_HARDWARE); 339 HPI_DEBUG_LOG(DEBUG, "adapter %d dsp crashed\n", 340 phm->adapter_index); 341 return; 342 } 343 } 344 /* Init default response including the size field */ 345 if (phm->function != HPI_SUBSYS_CREATE_ADAPTER) 346 hpi_init_response(phr, phm->object, phm->function, 347 HPI_ERROR_PROCESSING_MESSAGE); 348 349 switch (phm->type) { 350 case HPI_TYPE_REQUEST: 351 switch (phm->object) { 352 case HPI_OBJ_SUBSYSTEM: 353 subsys_message(phm, phr); 354 break; 355 356 case HPI_OBJ_ADAPTER: 357 phr->size = 358 sizeof(struct hpi_response_header) + 359 sizeof(struct hpi_adapter_res); 360 adapter_message(pao, phm, phr); 361 break; 362 363 case HPI_OBJ_CONTROL: 364 control_message(pao, phm, phr); 365 break; 366 367 case HPI_OBJ_OSTREAM: 368 outstream_message(pao, phm, phr); 369 break; 370 371 case HPI_OBJ_ISTREAM: 372 instream_message(pao, phm, phr); 373 break; 374 375 default: 376 hw_message(pao, phm, phr); 377 break; 378 } 379 break; 380 381 default: 382 phr->error = HPI_ERROR_INVALID_TYPE; 383 break; 384 } 385 } 386 387 /************************************************************************/ 388 /* SUBSYSTEM */ 389 390 /* create an adapter object and initialise it based on resource information 391 * passed in the message 392 * NOTE - you cannot use this function AND the FindAdapters function at the 393 * same time, the application must use only one of them to get the adapters 394 */ 395 static void subsys_create_adapter(struct hpi_message *phm, 396 struct hpi_response *phr) 397 { 398 /* create temp adapter obj, because we don't know what index yet */ 399 struct hpi_adapter_obj ao; 400 struct hpi_adapter_obj *pao; 401 u32 os_error_code; 402 u16 err = 0; 403 u32 dsp_index = 0; 404 405 HPI_DEBUG_LOG(VERBOSE, "subsys_create_adapter\n"); 406 407 memset(&ao, 0, sizeof(ao)); 408 409 ao.priv = kzalloc(sizeof(struct hpi_hw_obj), GFP_KERNEL); 410 if (!ao.priv) { 411 HPI_DEBUG_LOG(ERROR, "can't get mem for adapter object\n"); 412 phr->error = HPI_ERROR_MEMORY_ALLOC; 413 return; 414 } 415 416 /* create the adapter object based on the resource information */ 417 ao.pci = *phm->u.s.resource.r.pci; 418 419 err = create_adapter_obj(&ao, &os_error_code); 420 if (err) { 421 delete_adapter_obj(&ao); 422 if (err >= HPI_ERROR_BACKEND_BASE) { 423 phr->error = HPI_ERROR_DSP_BOOTLOAD; 424 phr->specific_error = err; 425 } else { 426 phr->error = err; 427 } 428 429 phr->u.s.data = os_error_code; 430 return; 431 } 432 /* need to update paParentAdapter */ 433 pao = hpi_find_adapter(ao.index); 434 if (!pao) { 435 /* We just added this adapter, why can't we find it!? */ 436 HPI_DEBUG_LOG(ERROR, "lost adapter after boot\n"); 437 phr->error = HPI_ERROR_BAD_ADAPTER; 438 return; 439 } 440 441 for (dsp_index = 0; dsp_index < MAX_DSPS; dsp_index++) { 442 struct hpi_hw_obj *phw = pao->priv; 443 phw->ado[dsp_index].pa_parent_adapter = pao; 444 } 445 446 phr->u.s.adapter_type = ao.type; 447 phr->u.s.adapter_index = ao.index; 448 phr->error = 0; 449 } 450 451 static void adapter_delete(struct hpi_adapter_obj *pao, 452 struct hpi_message *phm, struct hpi_response *phr) 453 { 454 delete_adapter_obj(pao); 455 hpi_delete_adapter(pao); 456 phr->error = 0; 457 } 458 459 /* this routine is called from SubSysFindAdapter and SubSysCreateAdapter */ 460 static short create_adapter_obj(struct hpi_adapter_obj *pao, 461 u32 *pos_error_code) 462 { 463 short boot_error = 0; 464 u32 dsp_index = 0; 465 u32 control_cache_size = 0; 466 u32 control_cache_count = 0; 467 struct hpi_hw_obj *phw = pao->priv; 468 469 /* The PCI2040 has the following address map */ 470 /* BAR0 - 4K = HPI control and status registers on PCI2040 (HPI CSR) */ 471 /* BAR1 - 32K = HPI registers on DSP */ 472 phw->dw2040_HPICSR = pao->pci.ap_mem_base[0]; 473 phw->dw2040_HPIDSP = pao->pci.ap_mem_base[1]; 474 HPI_DEBUG_LOG(VERBOSE, "csr %p, dsp %p\n", phw->dw2040_HPICSR, 475 phw->dw2040_HPIDSP); 476 477 /* set addresses for the possible DSP HPI interfaces */ 478 for (dsp_index = 0; dsp_index < MAX_DSPS; dsp_index++) { 479 phw->ado[dsp_index].prHPI_control = 480 phw->dw2040_HPIDSP + (CONTROL + 481 DSP_SPACING * dsp_index); 482 483 phw->ado[dsp_index].prHPI_address = 484 phw->dw2040_HPIDSP + (ADDRESS + 485 DSP_SPACING * dsp_index); 486 phw->ado[dsp_index].prHPI_data = 487 phw->dw2040_HPIDSP + (DATA + DSP_SPACING * dsp_index); 488 489 phw->ado[dsp_index].prHPI_data_auto_inc = 490 phw->dw2040_HPIDSP + (DATA_AUTOINC + 491 DSP_SPACING * dsp_index); 492 493 HPI_DEBUG_LOG(VERBOSE, "ctl %p, adr %p, dat %p, dat++ %p\n", 494 phw->ado[dsp_index].prHPI_control, 495 phw->ado[dsp_index].prHPI_address, 496 phw->ado[dsp_index].prHPI_data, 497 phw->ado[dsp_index].prHPI_data_auto_inc); 498 499 phw->ado[dsp_index].pa_parent_adapter = pao; 500 } 501 502 phw->pCI2040HPI_error_count = 0; 503 pao->has_control_cache = 0; 504 505 /* Set the default number of DSPs on this card */ 506 /* This is (conditionally) adjusted after bootloading */ 507 /* of the first DSP in the bootload section. */ 508 phw->num_dsp = 1; 509 510 boot_error = hpi6000_adapter_boot_load_dsp(pao, pos_error_code); 511 if (boot_error) 512 return boot_error; 513 514 HPI_DEBUG_LOG(INFO, "bootload DSP OK\n"); 515 516 phw->message_buffer_address_on_dsp = 0L; 517 phw->response_buffer_address_on_dsp = 0L; 518 519 /* get info about the adapter by asking the adapter */ 520 /* send a HPI_ADAPTER_GET_INFO message */ 521 { 522 struct hpi_message hm; 523 struct hpi_response hr0; /* response from DSP 0 */ 524 struct hpi_response hr1; /* response from DSP 1 */ 525 u16 error = 0; 526 527 HPI_DEBUG_LOG(VERBOSE, "send ADAPTER_GET_INFO\n"); 528 memset(&hm, 0, sizeof(hm)); 529 hm.type = HPI_TYPE_REQUEST; 530 hm.size = sizeof(struct hpi_message); 531 hm.object = HPI_OBJ_ADAPTER; 532 hm.function = HPI_ADAPTER_GET_INFO; 533 hm.adapter_index = 0; 534 memset(&hr0, 0, sizeof(hr0)); 535 memset(&hr1, 0, sizeof(hr1)); 536 hr0.size = sizeof(hr0); 537 hr1.size = sizeof(hr1); 538 539 error = hpi6000_message_response_sequence(pao, 0, &hm, &hr0); 540 if (hr0.error) { 541 HPI_DEBUG_LOG(DEBUG, "message error %d\n", hr0.error); 542 return hr0.error; 543 } 544 if (phw->num_dsp == 2) { 545 error = hpi6000_message_response_sequence(pao, 1, &hm, 546 &hr1); 547 if (error) 548 return error; 549 } 550 pao->type = hr0.u.ax.info.adapter_type; 551 pao->index = hr0.u.ax.info.adapter_index; 552 } 553 554 memset(&phw->control_cache[0], 0, 555 sizeof(struct hpi_control_cache_single) * 556 HPI_NMIXER_CONTROLS); 557 /* Read the control cache length to figure out if it is turned on */ 558 control_cache_size = 559 hpi_read_word(&phw->ado[0], 560 HPI_HIF_ADDR(control_cache_size_in_bytes)); 561 if (control_cache_size) { 562 control_cache_count = 563 hpi_read_word(&phw->ado[0], 564 HPI_HIF_ADDR(control_cache_count)); 565 566 phw->p_cache = 567 hpi_alloc_control_cache(control_cache_count, 568 control_cache_size, (unsigned char *) 569 &phw->control_cache[0] 570 ); 571 if (phw->p_cache) 572 pao->has_control_cache = 1; 573 } 574 575 HPI_DEBUG_LOG(DEBUG, "get adapter info ASI%04X index %d\n", pao->type, 576 pao->index); 577 578 if (phw->p_cache) 579 phw->p_cache->adap_idx = pao->index; 580 581 return hpi_add_adapter(pao); 582 } 583 584 static void delete_adapter_obj(struct hpi_adapter_obj *pao) 585 { 586 struct hpi_hw_obj *phw = pao->priv; 587 588 if (pao->has_control_cache) 589 hpi_free_control_cache(phw->p_cache); 590 591 /* reset DSPs on adapter */ 592 iowrite32(0x0003000F, phw->dw2040_HPICSR + HPI_RESET); 593 594 kfree(phw); 595 } 596 597 /************************************************************************/ 598 /* ADAPTER */ 599 600 static void adapter_get_asserts(struct hpi_adapter_obj *pao, 601 struct hpi_message *phm, struct hpi_response *phr) 602 { 603 #ifndef HIDE_PCI_ASSERTS 604 /* if we have PCI2040 asserts then collect them */ 605 if ((gw_pci_read_asserts > 0) || (gw_pci_write_asserts > 0)) { 606 phr->u.ax.assert.p1 = 607 gw_pci_read_asserts * 100 + gw_pci_write_asserts; 608 phr->u.ax.assert.p2 = 0; 609 phr->u.ax.assert.count = 1; /* assert count */ 610 phr->u.ax.assert.dsp_index = -1; /* "dsp index" */ 611 strcpy(phr->u.ax.assert.sz_message, "PCI2040 error"); 612 phr->u.ax.assert.dsp_msg_addr = 0; 613 gw_pci_read_asserts = 0; 614 gw_pci_write_asserts = 0; 615 phr->error = 0; 616 } else 617 #endif 618 hw_message(pao, phm, phr); /*get DSP asserts */ 619 620 return; 621 } 622 623 /************************************************************************/ 624 /* LOW-LEVEL */ 625 626 static short hpi6000_adapter_boot_load_dsp(struct hpi_adapter_obj *pao, 627 u32 *pos_error_code) 628 { 629 struct hpi_hw_obj *phw = pao->priv; 630 short error; 631 u32 timeout; 632 u32 read = 0; 633 u32 i = 0; 634 u32 data = 0; 635 u32 j = 0; 636 u32 test_addr = 0x80000000; 637 u32 test_data = 0x00000001; 638 u32 dw2040_reset = 0; 639 u32 dsp_index = 0; 640 u32 endian = 0; 641 u32 adapter_info = 0; 642 u32 delay = 0; 643 644 struct dsp_code dsp_code; 645 u16 boot_load_family = 0; 646 647 /* NOTE don't use wAdapterType in this routine. It is not setup yet */ 648 649 switch (pao->pci.pci_dev->subsystem_device) { 650 case 0x5100: 651 case 0x5110: /* ASI5100 revB or higher with C6711D */ 652 case 0x5200: /* ASI5200 PCIe version of ASI5100 */ 653 case 0x6100: 654 case 0x6200: 655 boot_load_family = HPI_ADAPTER_FAMILY_ASI(0x6200); 656 break; 657 default: 658 return HPI6000_ERROR_UNHANDLED_SUBSYS_ID; 659 } 660 661 /* reset all DSPs, indicate two DSPs are present 662 * set RST3-=1 to disconnect HAD8 to set DSP in little endian mode 663 */ 664 endian = 0; 665 dw2040_reset = 0x0003000F; 666 iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET); 667 668 /* read back register to make sure PCI2040 chip is functioning 669 * note that bits 4..15 are read-only and so should always return zero, 670 * even though we wrote 1 to them 671 */ 672 hpios_delay_micro_seconds(1000); 673 delay = ioread32(phw->dw2040_HPICSR + HPI_RESET); 674 675 if (delay != dw2040_reset) { 676 HPI_DEBUG_LOG(ERROR, "INIT_PCI2040 %x %x\n", dw2040_reset, 677 delay); 678 return HPI6000_ERROR_INIT_PCI2040; 679 } 680 681 /* Indicate that DSP#0,1 is a C6X */ 682 iowrite32(0x00000003, phw->dw2040_HPICSR + HPI_DATA_WIDTH); 683 /* set Bit30 and 29 - which will prevent Target aborts from being 684 * issued upon HPI or GP error 685 */ 686 iowrite32(0x60000000, phw->dw2040_HPICSR + INTERRUPT_MASK_SET); 687 688 /* isolate DSP HAD8 line from PCI2040 so that 689 * Little endian can be set by pullup 690 */ 691 dw2040_reset = dw2040_reset & (~(endian << 3)); 692 iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET); 693 694 phw->ado[0].c_dsp_rev = 'B'; /* revB */ 695 phw->ado[1].c_dsp_rev = 'B'; /* revB */ 696 697 /*Take both DSPs out of reset, setting HAD8 to the correct Endian */ 698 dw2040_reset = dw2040_reset & (~0x00000001); /* start DSP 0 */ 699 iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET); 700 dw2040_reset = dw2040_reset & (~0x00000002); /* start DSP 1 */ 701 iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET); 702 703 /* set HAD8 back to PCI2040, now that DSP set to little endian mode */ 704 dw2040_reset = dw2040_reset & (~0x00000008); 705 iowrite32(dw2040_reset, phw->dw2040_HPICSR + HPI_RESET); 706 /*delay to allow DSP to get going */ 707 hpios_delay_micro_seconds(100); 708 709 /* loop through all DSPs, downloading DSP code */ 710 for (dsp_index = 0; dsp_index < phw->num_dsp; dsp_index++) { 711 struct dsp_obj *pdo = &phw->ado[dsp_index]; 712 713 /* configure DSP so that we download code into the SRAM */ 714 /* set control reg for little endian, HWOB=1 */ 715 iowrite32(0x00010001, pdo->prHPI_control); 716 717 /* test access to the HPI address register (HPIA) */ 718 test_data = 0x00000001; 719 for (j = 0; j < 32; j++) { 720 iowrite32(test_data, pdo->prHPI_address); 721 data = ioread32(pdo->prHPI_address); 722 if (data != test_data) { 723 HPI_DEBUG_LOG(ERROR, "INIT_DSPHPI %x %x %x\n", 724 test_data, data, dsp_index); 725 return HPI6000_ERROR_INIT_DSPHPI; 726 } 727 test_data = test_data << 1; 728 } 729 730 /* if C6713 the setup PLL to generate 225MHz from 25MHz. 731 * Since the PLLDIV1 read is sometimes wrong, even on a C6713, 732 * we're going to do this unconditionally 733 */ 734 /* PLLDIV1 should have a value of 8000 after reset */ 735 /* 736 if (HpiReadWord(pdo,0x01B7C118) == 0x8000) 737 */ 738 { 739 /* C6713 datasheet says we cannot program PLL from HPI, 740 * and indeed if we try to set the PLL multiply from the 741 * HPI, the PLL does not seem to lock, 742 * so we enable the PLL and use the default of x 7 743 */ 744 /* bypass PLL */ 745 hpi_write_word(pdo, 0x01B7C100, 0x0000); 746 hpios_delay_micro_seconds(100); 747 748 /* ** use default of PLL x7 ** */ 749 /* EMIF = 225/3=75MHz */ 750 hpi_write_word(pdo, 0x01B7C120, 0x8002); 751 hpios_delay_micro_seconds(100); 752 753 /* peri = 225/2 */ 754 hpi_write_word(pdo, 0x01B7C11C, 0x8001); 755 hpios_delay_micro_seconds(100); 756 757 /* cpu = 225/1 */ 758 hpi_write_word(pdo, 0x01B7C118, 0x8000); 759 760 /* ~2ms delay */ 761 hpios_delay_micro_seconds(2000); 762 763 /* PLL not bypassed */ 764 hpi_write_word(pdo, 0x01B7C100, 0x0001); 765 /* ~2ms delay */ 766 hpios_delay_micro_seconds(2000); 767 } 768 769 /* test r/w to internal DSP memory 770 * C6711 has L2 cache mapped to 0x0 when reset 771 * 772 * revB - because of bug 3.0.1 last HPI read 773 * (before HPI address issued) must be non-autoinc 774 */ 775 /* test each bit in the 32bit word */ 776 for (i = 0; i < 100; i++) { 777 test_addr = 0x00000000; 778 test_data = 0x00000001; 779 for (j = 0; j < 32; j++) { 780 hpi_write_word(pdo, test_addr + i, test_data); 781 data = hpi_read_word(pdo, test_addr + i); 782 if (data != test_data) { 783 HPI_DEBUG_LOG(ERROR, 784 "DSP mem %x %x %x %x\n", 785 test_addr + i, test_data, 786 data, dsp_index); 787 788 return HPI6000_ERROR_INIT_DSPINTMEM; 789 } 790 test_data = test_data << 1; 791 } 792 } 793 794 /* memory map of ASI6200 795 00000000-0000FFFF 16Kx32 internal program 796 01800000-019FFFFF Internal peripheral 797 80000000-807FFFFF CE0 2Mx32 SDRAM running @ 100MHz 798 90000000-9000FFFF CE1 Async peripherals: 799 800 EMIF config 801 ------------ 802 Global EMIF control 803 0 - 804 1 - 805 2 - 806 3 CLK2EN = 1 CLKOUT2 enabled 807 4 CLK1EN = 0 CLKOUT1 disabled 808 5 EKEN = 1 <--!! C6713 specific, enables ECLKOUT 809 6 - 810 7 NOHOLD = 1 external HOLD disabled 811 8 HOLDA = 0 HOLDA output is low 812 9 HOLD = 0 HOLD input is low 813 10 ARDY = 1 ARDY input is high 814 11 BUSREQ = 0 BUSREQ output is low 815 12,13 Reserved = 1 816 */ 817 hpi_write_word(pdo, 0x01800000, 0x34A8); 818 819 /* EMIF CE0 setup - 2Mx32 Sync DRAM 820 31..28 Wr setup 821 27..22 Wr strobe 822 21..20 Wr hold 823 19..16 Rd setup 824 15..14 - 825 13..8 Rd strobe 826 7..4 MTYPE 0011 Sync DRAM 32bits 827 3 Wr hold MSB 828 2..0 Rd hold 829 */ 830 hpi_write_word(pdo, 0x01800008, 0x00000030); 831 832 /* EMIF SDRAM Extension 833 31-21 0 834 20 WR2RD = 0 835 19-18 WR2DEAC = 1 836 17 WR2WR = 0 837 16-15 R2WDQM = 2 838 14-12 RD2WR = 4 839 11-10 RD2DEAC = 1 840 9 RD2RD = 1 841 8-7 THZP = 10b 842 6-5 TWR = 2-1 = 01b (tWR = 10ns) 843 4 TRRD = 0b = 2 ECLK (tRRD = 14ns) 844 3-1 TRAS = 5-1 = 100b (Tras=42ns = 5 ECLK) 845 1 CAS latency = 3 ECLK 846 (for Micron 2M32-7 operating at 100Mhz) 847 */ 848 849 /* need to use this else DSP code crashes */ 850 hpi_write_word(pdo, 0x01800020, 0x001BDF29); 851 852 /* EMIF SDRAM control - set up for a 2Mx32 SDRAM (512x32x4 bank) 853 31 - - 854 30 SDBSZ 1 4 bank 855 29..28 SDRSZ 00 11 row address pins 856 27..26 SDCSZ 01 8 column address pins 857 25 RFEN 1 refersh enabled 858 24 INIT 1 init SDRAM 859 23..20 TRCD 0001 860 19..16 TRP 0001 861 15..12 TRC 0110 862 11..0 - - 863 */ 864 /* need to use this else DSP code crashes */ 865 hpi_write_word(pdo, 0x01800018, 0x47117000); 866 867 /* EMIF SDRAM Refresh Timing */ 868 hpi_write_word(pdo, 0x0180001C, 0x00000410); 869 870 /*MIF CE1 setup - Async peripherals 871 @100MHz bus speed, each cycle is 10ns, 872 31..28 Wr setup = 1 873 27..22 Wr strobe = 3 30ns 874 21..20 Wr hold = 1 875 19..16 Rd setup =1 876 15..14 Ta = 2 877 13..8 Rd strobe = 3 30ns 878 7..4 MTYPE 0010 Async 32bits 879 3 Wr hold MSB =0 880 2..0 Rd hold = 1 881 */ 882 { 883 u32 cE1 = 884 (1L << 28) | (3L << 22) | (1L << 20) | (1L << 885 16) | (2L << 14) | (3L << 8) | (2L << 4) | 1L; 886 hpi_write_word(pdo, 0x01800004, cE1); 887 } 888 889 /* delay a little to allow SDRAM and DSP to "get going" */ 890 hpios_delay_micro_seconds(1000); 891 892 /* test access to SDRAM */ 893 { 894 test_addr = 0x80000000; 895 test_data = 0x00000001; 896 /* test each bit in the 32bit word */ 897 for (j = 0; j < 32; j++) { 898 hpi_write_word(pdo, test_addr, test_data); 899 data = hpi_read_word(pdo, test_addr); 900 if (data != test_data) { 901 HPI_DEBUG_LOG(ERROR, 902 "DSP dram %x %x %x %x\n", 903 test_addr, test_data, data, 904 dsp_index); 905 906 return HPI6000_ERROR_INIT_SDRAM1; 907 } 908 test_data = test_data << 1; 909 } 910 /* test every Nth address in the DRAM */ 911 #define DRAM_SIZE_WORDS 0x200000 /*2_mx32 */ 912 #define DRAM_INC 1024 913 test_addr = 0x80000000; 914 test_data = 0x0; 915 for (i = 0; i < DRAM_SIZE_WORDS; i = i + DRAM_INC) { 916 hpi_write_word(pdo, test_addr + i, test_data); 917 test_data++; 918 } 919 test_addr = 0x80000000; 920 test_data = 0x0; 921 for (i = 0; i < DRAM_SIZE_WORDS; i = i + DRAM_INC) { 922 data = hpi_read_word(pdo, test_addr + i); 923 if (data != test_data) { 924 HPI_DEBUG_LOG(ERROR, 925 "DSP dram %x %x %x %x\n", 926 test_addr + i, test_data, 927 data, dsp_index); 928 return HPI6000_ERROR_INIT_SDRAM2; 929 } 930 test_data++; 931 } 932 933 } 934 935 /* write the DSP code down into the DSPs memory */ 936 error = hpi_dsp_code_open(boot_load_family, pao->pci.pci_dev, 937 &dsp_code, pos_error_code); 938 939 if (error) 940 return error; 941 942 while (1) { 943 u32 length; 944 u32 address; 945 u32 type; 946 u32 *pcode; 947 948 error = hpi_dsp_code_read_word(&dsp_code, &length); 949 if (error) 950 break; 951 if (length == 0xFFFFFFFF) 952 break; /* end of code */ 953 954 error = hpi_dsp_code_read_word(&dsp_code, &address); 955 if (error) 956 break; 957 error = hpi_dsp_code_read_word(&dsp_code, &type); 958 if (error) 959 break; 960 error = hpi_dsp_code_read_block(length, &dsp_code, 961 &pcode); 962 if (error) 963 break; 964 error = hpi6000_dsp_block_write32(pao, (u16)dsp_index, 965 address, pcode, length); 966 if (error) 967 break; 968 } 969 970 if (error) { 971 hpi_dsp_code_close(&dsp_code); 972 return error; 973 } 974 /* verify that code was written correctly */ 975 /* this time through, assume no errors in DSP code file/array */ 976 hpi_dsp_code_rewind(&dsp_code); 977 while (1) { 978 u32 length; 979 u32 address; 980 u32 type; 981 u32 *pcode; 982 983 hpi_dsp_code_read_word(&dsp_code, &length); 984 if (length == 0xFFFFFFFF) 985 break; /* end of code */ 986 987 hpi_dsp_code_read_word(&dsp_code, &address); 988 hpi_dsp_code_read_word(&dsp_code, &type); 989 hpi_dsp_code_read_block(length, &dsp_code, &pcode); 990 991 for (i = 0; i < length; i++) { 992 data = hpi_read_word(pdo, address); 993 if (data != *pcode) { 994 error = HPI6000_ERROR_INIT_VERIFY; 995 HPI_DEBUG_LOG(ERROR, 996 "DSP verify %x %x %x %x\n", 997 address, *pcode, data, 998 dsp_index); 999 break; 1000 } 1001 pcode++; 1002 address += 4; 1003 } 1004 if (error) 1005 break; 1006 } 1007 hpi_dsp_code_close(&dsp_code); 1008 if (error) 1009 return error; 1010 1011 /* zero out the hostmailbox */ 1012 { 1013 u32 address = HPI_HIF_ADDR(host_cmd); 1014 for (i = 0; i < 4; i++) { 1015 hpi_write_word(pdo, address, 0); 1016 address += 4; 1017 } 1018 } 1019 /* write the DSP number into the hostmailbox */ 1020 /* structure before starting the DSP */ 1021 hpi_write_word(pdo, HPI_HIF_ADDR(dsp_number), dsp_index); 1022 1023 /* write the DSP adapter Info into the */ 1024 /* hostmailbox before starting the DSP */ 1025 if (dsp_index > 0) 1026 hpi_write_word(pdo, HPI_HIF_ADDR(adapter_info), 1027 adapter_info); 1028 1029 /* step 3. Start code by sending interrupt */ 1030 iowrite32(0x00030003, pdo->prHPI_control); 1031 hpios_delay_micro_seconds(10000); 1032 1033 /* wait for a non-zero value in hostcmd - 1034 * indicating initialization is complete 1035 * 1036 * Init could take a while if DSP checks SDRAM memory 1037 * Was 200000. Increased to 2000000 for ASI8801 so we 1038 * don't get 938 errors. 1039 */ 1040 timeout = 2000000; 1041 while (timeout) { 1042 do { 1043 read = hpi_read_word(pdo, 1044 HPI_HIF_ADDR(host_cmd)); 1045 } while (--timeout 1046 && hpi6000_check_PCI2040_error_flag(pao, 1047 H6READ)); 1048 1049 if (read) 1050 break; 1051 /* The following is a workaround for bug #94: 1052 * Bluescreen on install and subsequent boots on a 1053 * DELL PowerEdge 600SC PC with 1.8GHz P4 and 1054 * ServerWorks chipset. Without this delay the system 1055 * locks up with a bluescreen (NOT GPF or pagefault). 1056 */ 1057 else 1058 hpios_delay_micro_seconds(10000); 1059 } 1060 if (timeout == 0) 1061 return HPI6000_ERROR_INIT_NOACK; 1062 1063 /* read the DSP adapter Info from the */ 1064 /* hostmailbox structure after starting the DSP */ 1065 if (dsp_index == 0) { 1066 /*u32 dwTestData=0; */ 1067 u32 mask = 0; 1068 1069 adapter_info = 1070 hpi_read_word(pdo, 1071 HPI_HIF_ADDR(adapter_info)); 1072 if (HPI_ADAPTER_FAMILY_ASI 1073 (HPI_HIF_ADAPTER_INFO_EXTRACT_ADAPTER 1074 (adapter_info)) == 1075 HPI_ADAPTER_FAMILY_ASI(0x6200)) 1076 /* all 6200 cards have this many DSPs */ 1077 phw->num_dsp = 2; 1078 1079 /* test that the PLD is programmed */ 1080 /* and we can read/write 24bits */ 1081 #define PLD_BASE_ADDRESS 0x90000000L /*for ASI6100/6200/8800 */ 1082 1083 switch (boot_load_family) { 1084 case HPI_ADAPTER_FAMILY_ASI(0x6200): 1085 /* ASI6100/6200 has 24bit path to FPGA */ 1086 mask = 0xFFFFFF00L; 1087 /* ASI5100 uses AX6 code, */ 1088 /* but has no PLD r/w register to test */ 1089 if (HPI_ADAPTER_FAMILY_ASI(pao->pci.pci_dev-> 1090 subsystem_device) == 1091 HPI_ADAPTER_FAMILY_ASI(0x5100)) 1092 mask = 0x00000000L; 1093 /* ASI5200 uses AX6 code, */ 1094 /* but has no PLD r/w register to test */ 1095 if (HPI_ADAPTER_FAMILY_ASI(pao->pci.pci_dev-> 1096 subsystem_device) == 1097 HPI_ADAPTER_FAMILY_ASI(0x5200)) 1098 mask = 0x00000000L; 1099 break; 1100 case HPI_ADAPTER_FAMILY_ASI(0x8800): 1101 /* ASI8800 has 16bit path to FPGA */ 1102 mask = 0xFFFF0000L; 1103 break; 1104 } 1105 test_data = 0xAAAAAA00L & mask; 1106 /* write to 24 bit Debug register (D31-D8) */ 1107 hpi_write_word(pdo, PLD_BASE_ADDRESS + 4L, test_data); 1108 read = hpi_read_word(pdo, 1109 PLD_BASE_ADDRESS + 4L) & mask; 1110 if (read != test_data) { 1111 HPI_DEBUG_LOG(ERROR, "PLD %x %x\n", test_data, 1112 read); 1113 return HPI6000_ERROR_INIT_PLDTEST1; 1114 } 1115 test_data = 0x55555500L & mask; 1116 hpi_write_word(pdo, PLD_BASE_ADDRESS + 4L, test_data); 1117 read = hpi_read_word(pdo, 1118 PLD_BASE_ADDRESS + 4L) & mask; 1119 if (read != test_data) { 1120 HPI_DEBUG_LOG(ERROR, "PLD %x %x\n", test_data, 1121 read); 1122 return HPI6000_ERROR_INIT_PLDTEST2; 1123 } 1124 } 1125 } /* for numDSP */ 1126 return 0; 1127 } 1128 1129 #define PCI_TIMEOUT 100 1130 1131 static int hpi_set_address(struct dsp_obj *pdo, u32 address) 1132 { 1133 u32 timeout = PCI_TIMEOUT; 1134 1135 do { 1136 iowrite32(address, pdo->prHPI_address); 1137 } while (hpi6000_check_PCI2040_error_flag(pdo->pa_parent_adapter, 1138 H6WRITE) 1139 && --timeout); 1140 1141 if (timeout) 1142 return 0; 1143 1144 return 1; 1145 } 1146 1147 /* write one word to the HPI port */ 1148 static void hpi_write_word(struct dsp_obj *pdo, u32 address, u32 data) 1149 { 1150 if (hpi_set_address(pdo, address)) 1151 return; 1152 iowrite32(data, pdo->prHPI_data); 1153 } 1154 1155 /* read one word from the HPI port */ 1156 static u32 hpi_read_word(struct dsp_obj *pdo, u32 address) 1157 { 1158 u32 data = 0; 1159 1160 if (hpi_set_address(pdo, address)) 1161 return 0; /*? No way to return error */ 1162 1163 /* take care of errata in revB DSP (2.0.1) */ 1164 data = ioread32(pdo->prHPI_data); 1165 return data; 1166 } 1167 1168 /* write a block of 32bit words to the DSP HPI port using auto-inc mode */ 1169 static void hpi_write_block(struct dsp_obj *pdo, u32 address, u32 *pdata, 1170 u32 length) 1171 { 1172 u16 length16 = length - 1; 1173 1174 if (length == 0) 1175 return; 1176 1177 if (hpi_set_address(pdo, address)) 1178 return; 1179 1180 iowrite32_rep(pdo->prHPI_data_auto_inc, pdata, length16); 1181 1182 /* take care of errata in revB DSP (2.0.1) */ 1183 /* must end with non auto-inc */ 1184 iowrite32(*(pdata + length - 1), pdo->prHPI_data); 1185 } 1186 1187 /** read a block of 32bit words from the DSP HPI port using auto-inc mode 1188 */ 1189 static void hpi_read_block(struct dsp_obj *pdo, u32 address, u32 *pdata, 1190 u32 length) 1191 { 1192 u16 length16 = length - 1; 1193 1194 if (length == 0) 1195 return; 1196 1197 if (hpi_set_address(pdo, address)) 1198 return; 1199 1200 ioread32_rep(pdo->prHPI_data_auto_inc, pdata, length16); 1201 1202 /* take care of errata in revB DSP (2.0.1) */ 1203 /* must end with non auto-inc */ 1204 *(pdata + length - 1) = ioread32(pdo->prHPI_data); 1205 } 1206 1207 static u16 hpi6000_dsp_block_write32(struct hpi_adapter_obj *pao, 1208 u16 dsp_index, u32 hpi_address, u32 *source, u32 count) 1209 { 1210 struct hpi_hw_obj *phw = pao->priv; 1211 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1212 u32 time_out = PCI_TIMEOUT; 1213 int c6711_burst_size = 128; 1214 u32 local_hpi_address = hpi_address; 1215 int local_count = count; 1216 int xfer_size; 1217 u32 *pdata = source; 1218 1219 while (local_count) { 1220 if (local_count > c6711_burst_size) 1221 xfer_size = c6711_burst_size; 1222 else 1223 xfer_size = local_count; 1224 1225 time_out = PCI_TIMEOUT; 1226 do { 1227 hpi_write_block(pdo, local_hpi_address, pdata, 1228 xfer_size); 1229 } while (hpi6000_check_PCI2040_error_flag(pao, H6WRITE) 1230 && --time_out); 1231 1232 if (!time_out) 1233 break; 1234 pdata += xfer_size; 1235 local_hpi_address += sizeof(u32) * xfer_size; 1236 local_count -= xfer_size; 1237 } 1238 1239 if (time_out) 1240 return 0; 1241 else 1242 return 1; 1243 } 1244 1245 static u16 hpi6000_dsp_block_read32(struct hpi_adapter_obj *pao, 1246 u16 dsp_index, u32 hpi_address, u32 *dest, u32 count) 1247 { 1248 struct hpi_hw_obj *phw = pao->priv; 1249 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1250 u32 time_out = PCI_TIMEOUT; 1251 int c6711_burst_size = 16; 1252 u32 local_hpi_address = hpi_address; 1253 int local_count = count; 1254 int xfer_size; 1255 u32 *pdata = dest; 1256 1257 while (local_count) { 1258 if (local_count > c6711_burst_size) 1259 xfer_size = c6711_burst_size; 1260 else 1261 xfer_size = local_count; 1262 1263 time_out = PCI_TIMEOUT; 1264 do { 1265 hpi_read_block(pdo, local_hpi_address, pdata, 1266 xfer_size); 1267 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) 1268 && --time_out); 1269 if (!time_out) 1270 break; 1271 1272 pdata += xfer_size; 1273 local_hpi_address += sizeof(u32) * xfer_size; 1274 local_count -= xfer_size; 1275 } 1276 1277 if (time_out) 1278 return 0; 1279 else 1280 return 1; 1281 } 1282 1283 static short hpi6000_message_response_sequence(struct hpi_adapter_obj *pao, 1284 u16 dsp_index, struct hpi_message *phm, struct hpi_response *phr) 1285 { 1286 struct hpi_hw_obj *phw = pao->priv; 1287 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1288 u32 timeout; 1289 u16 ack; 1290 u32 address; 1291 u32 length; 1292 u32 *p_data; 1293 u16 error = 0; 1294 1295 ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_IDLE); 1296 if (ack & HPI_HIF_ERROR_MASK) { 1297 pao->dsp_crashed++; 1298 return HPI6000_ERROR_MSG_RESP_IDLE_TIMEOUT; 1299 } 1300 pao->dsp_crashed = 0; 1301 1302 /* get the message address and size */ 1303 if (phw->message_buffer_address_on_dsp == 0) { 1304 timeout = TIMEOUT; 1305 do { 1306 address = 1307 hpi_read_word(pdo, 1308 HPI_HIF_ADDR(message_buffer_address)); 1309 phw->message_buffer_address_on_dsp = address; 1310 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) 1311 && --timeout); 1312 if (!timeout) 1313 return HPI6000_ERROR_MSG_GET_ADR; 1314 } else 1315 address = phw->message_buffer_address_on_dsp; 1316 1317 length = phm->size; 1318 1319 /* send the message */ 1320 p_data = (u32 *)phm; 1321 if (hpi6000_dsp_block_write32(pao, dsp_index, address, p_data, 1322 (u16)length / 4)) 1323 return HPI6000_ERROR_MSG_RESP_BLOCKWRITE32; 1324 1325 if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_GET_RESP)) 1326 return HPI6000_ERROR_MSG_RESP_GETRESPCMD; 1327 hpi6000_send_dsp_interrupt(pdo); 1328 1329 ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_GET_RESP); 1330 if (ack & HPI_HIF_ERROR_MASK) 1331 return HPI6000_ERROR_MSG_RESP_GET_RESP_ACK; 1332 1333 /* get the response address */ 1334 if (phw->response_buffer_address_on_dsp == 0) { 1335 timeout = TIMEOUT; 1336 do { 1337 address = 1338 hpi_read_word(pdo, 1339 HPI_HIF_ADDR(response_buffer_address)); 1340 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) 1341 && --timeout); 1342 phw->response_buffer_address_on_dsp = address; 1343 1344 if (!timeout) 1345 return HPI6000_ERROR_RESP_GET_ADR; 1346 } else 1347 address = phw->response_buffer_address_on_dsp; 1348 1349 /* read the length of the response back from the DSP */ 1350 timeout = TIMEOUT; 1351 do { 1352 length = hpi_read_word(pdo, HPI_HIF_ADDR(length)); 1353 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) && --timeout); 1354 if (!timeout) 1355 return HPI6000_ERROR_RESP_GET_LEN; 1356 1357 if (length > phr->size) 1358 return HPI_ERROR_RESPONSE_BUFFER_TOO_SMALL; 1359 1360 /* get the response */ 1361 p_data = (u32 *)phr; 1362 if (hpi6000_dsp_block_read32(pao, dsp_index, address, p_data, 1363 (u16)length / 4)) 1364 return HPI6000_ERROR_MSG_RESP_BLOCKREAD32; 1365 1366 /* set i/f back to idle */ 1367 if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_IDLE)) 1368 return HPI6000_ERROR_MSG_RESP_IDLECMD; 1369 hpi6000_send_dsp_interrupt(pdo); 1370 1371 error = hpi_validate_response(phm, phr); 1372 return error; 1373 } 1374 1375 /* have to set up the below defines to match stuff in the MAP file */ 1376 1377 #define MSG_ADDRESS (HPI_HIF_BASE+0x18) 1378 #define MSG_LENGTH 11 1379 #define RESP_ADDRESS (HPI_HIF_BASE+0x44) 1380 #define RESP_LENGTH 16 1381 #define QUEUE_START (HPI_HIF_BASE+0x88) 1382 #define QUEUE_SIZE 0x8000 1383 1384 static short hpi6000_send_data_check_adr(u32 address, u32 length_in_dwords) 1385 { 1386 /*#define CHECKING // comment this line in to enable checking */ 1387 #ifdef CHECKING 1388 if (address < (u32)MSG_ADDRESS) 1389 return 0; 1390 if (address > (u32)(QUEUE_START + QUEUE_SIZE)) 1391 return 0; 1392 if ((address + (length_in_dwords << 2)) > 1393 (u32)(QUEUE_START + QUEUE_SIZE)) 1394 return 0; 1395 #else 1396 (void)address; 1397 (void)length_in_dwords; 1398 return 1; 1399 #endif 1400 } 1401 1402 static short hpi6000_send_data(struct hpi_adapter_obj *pao, u16 dsp_index, 1403 struct hpi_message *phm, struct hpi_response *phr) 1404 { 1405 struct hpi_hw_obj *phw = pao->priv; 1406 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1407 u32 data_sent = 0; 1408 u16 ack; 1409 u32 length, address; 1410 u32 *p_data = (u32 *)phm->u.d.u.data.pb_data; 1411 u16 time_out = 8; 1412 1413 (void)phr; 1414 1415 /* round dwDataSize down to nearest 4 bytes */ 1416 while ((data_sent < (phm->u.d.u.data.data_size & ~3L)) 1417 && --time_out) { 1418 ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_IDLE); 1419 if (ack & HPI_HIF_ERROR_MASK) 1420 return HPI6000_ERROR_SEND_DATA_IDLE_TIMEOUT; 1421 1422 if (hpi6000_send_host_command(pao, dsp_index, 1423 HPI_HIF_SEND_DATA)) 1424 return HPI6000_ERROR_SEND_DATA_CMD; 1425 1426 hpi6000_send_dsp_interrupt(pdo); 1427 1428 ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_SEND_DATA); 1429 1430 if (ack & HPI_HIF_ERROR_MASK) 1431 return HPI6000_ERROR_SEND_DATA_ACK; 1432 1433 do { 1434 /* get the address and size */ 1435 address = hpi_read_word(pdo, HPI_HIF_ADDR(address)); 1436 /* DSP returns number of DWORDS */ 1437 length = hpi_read_word(pdo, HPI_HIF_ADDR(length)); 1438 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ)); 1439 1440 if (!hpi6000_send_data_check_adr(address, length)) 1441 return HPI6000_ERROR_SEND_DATA_ADR; 1442 1443 /* send the data. break data into 512 DWORD blocks (2K bytes) 1444 * and send using block write. 2Kbytes is the max as this is the 1445 * memory window given to the HPI data register by the PCI2040 1446 */ 1447 1448 { 1449 u32 len = length; 1450 u32 blk_len = 512; 1451 while (len) { 1452 if (len < blk_len) 1453 blk_len = len; 1454 if (hpi6000_dsp_block_write32(pao, dsp_index, 1455 address, p_data, blk_len)) 1456 return HPI6000_ERROR_SEND_DATA_WRITE; 1457 address += blk_len * 4; 1458 p_data += blk_len; 1459 len -= blk_len; 1460 } 1461 } 1462 1463 if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_IDLE)) 1464 return HPI6000_ERROR_SEND_DATA_IDLECMD; 1465 1466 hpi6000_send_dsp_interrupt(pdo); 1467 1468 data_sent += length * 4; 1469 } 1470 if (!time_out) 1471 return HPI6000_ERROR_SEND_DATA_TIMEOUT; 1472 return 0; 1473 } 1474 1475 static short hpi6000_get_data(struct hpi_adapter_obj *pao, u16 dsp_index, 1476 struct hpi_message *phm, struct hpi_response *phr) 1477 { 1478 struct hpi_hw_obj *phw = pao->priv; 1479 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1480 u32 data_got = 0; 1481 u16 ack; 1482 u32 length, address; 1483 u32 *p_data = (u32 *)phm->u.d.u.data.pb_data; 1484 1485 (void)phr; /* this parameter not used! */ 1486 1487 /* round dwDataSize down to nearest 4 bytes */ 1488 while (data_got < (phm->u.d.u.data.data_size & ~3L)) { 1489 ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_IDLE); 1490 if (ack & HPI_HIF_ERROR_MASK) 1491 return HPI6000_ERROR_GET_DATA_IDLE_TIMEOUT; 1492 1493 if (hpi6000_send_host_command(pao, dsp_index, 1494 HPI_HIF_GET_DATA)) 1495 return HPI6000_ERROR_GET_DATA_CMD; 1496 hpi6000_send_dsp_interrupt(pdo); 1497 1498 ack = hpi6000_wait_dsp_ack(pao, dsp_index, HPI_HIF_GET_DATA); 1499 1500 if (ack & HPI_HIF_ERROR_MASK) 1501 return HPI6000_ERROR_GET_DATA_ACK; 1502 1503 /* get the address and size */ 1504 do { 1505 address = hpi_read_word(pdo, HPI_HIF_ADDR(address)); 1506 length = hpi_read_word(pdo, HPI_HIF_ADDR(length)); 1507 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ)); 1508 1509 /* read the data */ 1510 { 1511 u32 len = length; 1512 u32 blk_len = 512; 1513 while (len) { 1514 if (len < blk_len) 1515 blk_len = len; 1516 if (hpi6000_dsp_block_read32(pao, dsp_index, 1517 address, p_data, blk_len)) 1518 return HPI6000_ERROR_GET_DATA_READ; 1519 address += blk_len * 4; 1520 p_data += blk_len; 1521 len -= blk_len; 1522 } 1523 } 1524 1525 if (hpi6000_send_host_command(pao, dsp_index, HPI_HIF_IDLE)) 1526 return HPI6000_ERROR_GET_DATA_IDLECMD; 1527 hpi6000_send_dsp_interrupt(pdo); 1528 1529 data_got += length * 4; 1530 } 1531 return 0; 1532 } 1533 1534 static void hpi6000_send_dsp_interrupt(struct dsp_obj *pdo) 1535 { 1536 iowrite32(0x00030003, pdo->prHPI_control); /* DSPINT */ 1537 } 1538 1539 static short hpi6000_send_host_command(struct hpi_adapter_obj *pao, 1540 u16 dsp_index, u32 host_cmd) 1541 { 1542 struct hpi_hw_obj *phw = pao->priv; 1543 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1544 u32 timeout = TIMEOUT; 1545 1546 /* set command */ 1547 do { 1548 hpi_write_word(pdo, HPI_HIF_ADDR(host_cmd), host_cmd); 1549 /* flush the FIFO */ 1550 hpi_set_address(pdo, HPI_HIF_ADDR(host_cmd)); 1551 } while (hpi6000_check_PCI2040_error_flag(pao, H6WRITE) && --timeout); 1552 1553 /* reset the interrupt bit */ 1554 iowrite32(0x00040004, pdo->prHPI_control); 1555 1556 if (timeout) 1557 return 0; 1558 else 1559 return 1; 1560 } 1561 1562 /* if the PCI2040 has recorded an HPI timeout, reset the error and return 1 */ 1563 static short hpi6000_check_PCI2040_error_flag(struct hpi_adapter_obj *pao, 1564 u16 read_or_write) 1565 { 1566 u32 hPI_error; 1567 1568 struct hpi_hw_obj *phw = pao->priv; 1569 1570 /* read the error bits from the PCI2040 */ 1571 hPI_error = ioread32(phw->dw2040_HPICSR + HPI_ERROR_REPORT); 1572 if (hPI_error) { 1573 /* reset the error flag */ 1574 iowrite32(0L, phw->dw2040_HPICSR + HPI_ERROR_REPORT); 1575 phw->pCI2040HPI_error_count++; 1576 if (read_or_write == 1) 1577 gw_pci_read_asserts++; /************* inc global */ 1578 else 1579 gw_pci_write_asserts++; 1580 return 1; 1581 } else 1582 return 0; 1583 } 1584 1585 static short hpi6000_wait_dsp_ack(struct hpi_adapter_obj *pao, u16 dsp_index, 1586 u32 ack_value) 1587 { 1588 struct hpi_hw_obj *phw = pao->priv; 1589 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1590 u32 ack = 0L; 1591 u32 timeout; 1592 u32 hPIC = 0L; 1593 1594 /* wait for host interrupt to signal ack is ready */ 1595 timeout = TIMEOUT; 1596 while (--timeout) { 1597 hPIC = ioread32(pdo->prHPI_control); 1598 if (hPIC & 0x04) /* 0x04 = HINT from DSP */ 1599 break; 1600 } 1601 if (timeout == 0) 1602 return HPI_HIF_ERROR_MASK; 1603 1604 /* wait for dwAckValue */ 1605 timeout = TIMEOUT; 1606 while (--timeout) { 1607 /* read the ack mailbox */ 1608 ack = hpi_read_word(pdo, HPI_HIF_ADDR(dsp_ack)); 1609 if (ack == ack_value) 1610 break; 1611 if ((ack & HPI_HIF_ERROR_MASK) 1612 && !hpi6000_check_PCI2040_error_flag(pao, H6READ)) 1613 break; 1614 /*for (i=0;i<1000;i++) */ 1615 /* dwPause=i+1; */ 1616 } 1617 if (ack & HPI_HIF_ERROR_MASK) 1618 /* indicates bad read from DSP - 1619 typically 0xffffff is read for some reason */ 1620 ack = HPI_HIF_ERROR_MASK; 1621 1622 if (timeout == 0) 1623 ack = HPI_HIF_ERROR_MASK; 1624 return (short)ack; 1625 } 1626 1627 static short hpi6000_update_control_cache(struct hpi_adapter_obj *pao, 1628 struct hpi_message *phm) 1629 { 1630 const u16 dsp_index = 0; 1631 struct hpi_hw_obj *phw = pao->priv; 1632 struct dsp_obj *pdo = &phw->ado[dsp_index]; 1633 u32 timeout; 1634 u32 cache_dirty_flag; 1635 u16 err; 1636 1637 hpios_dsplock_lock(pao); 1638 1639 timeout = TIMEOUT; 1640 do { 1641 cache_dirty_flag = 1642 hpi_read_word((struct dsp_obj *)pdo, 1643 HPI_HIF_ADDR(control_cache_is_dirty)); 1644 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) && --timeout); 1645 if (!timeout) { 1646 err = HPI6000_ERROR_CONTROL_CACHE_PARAMS; 1647 goto unlock; 1648 } 1649 1650 if (cache_dirty_flag) { 1651 /* read the cached controls */ 1652 u32 address; 1653 u32 length; 1654 1655 timeout = TIMEOUT; 1656 if (pdo->control_cache_address_on_dsp == 0) { 1657 do { 1658 address = 1659 hpi_read_word((struct dsp_obj *)pdo, 1660 HPI_HIF_ADDR(control_cache_address)); 1661 1662 length = hpi_read_word((struct dsp_obj *)pdo, 1663 HPI_HIF_ADDR 1664 (control_cache_size_in_bytes)); 1665 } while (hpi6000_check_PCI2040_error_flag(pao, H6READ) 1666 && --timeout); 1667 if (!timeout) { 1668 err = HPI6000_ERROR_CONTROL_CACHE_ADDRLEN; 1669 goto unlock; 1670 } 1671 pdo->control_cache_address_on_dsp = address; 1672 pdo->control_cache_length_on_dsp = length; 1673 } else { 1674 address = pdo->control_cache_address_on_dsp; 1675 length = pdo->control_cache_length_on_dsp; 1676 } 1677 1678 if (hpi6000_dsp_block_read32(pao, dsp_index, address, 1679 (u32 *)&phw->control_cache[0], 1680 length / sizeof(u32))) { 1681 err = HPI6000_ERROR_CONTROL_CACHE_READ; 1682 goto unlock; 1683 } 1684 do { 1685 hpi_write_word((struct dsp_obj *)pdo, 1686 HPI_HIF_ADDR(control_cache_is_dirty), 0); 1687 /* flush the FIFO */ 1688 hpi_set_address(pdo, HPI_HIF_ADDR(host_cmd)); 1689 } while (hpi6000_check_PCI2040_error_flag(pao, H6WRITE) 1690 && --timeout); 1691 if (!timeout) { 1692 err = HPI6000_ERROR_CONTROL_CACHE_FLUSH; 1693 goto unlock; 1694 } 1695 1696 } 1697 err = 0; 1698 1699 unlock: 1700 hpios_dsplock_unlock(pao); 1701 return err; 1702 } 1703 1704 /** Get dsp index for multi DSP adapters only */ 1705 static u16 get_dsp_index(struct hpi_adapter_obj *pao, struct hpi_message *phm) 1706 { 1707 u16 ret = 0; 1708 switch (phm->object) { 1709 case HPI_OBJ_ISTREAM: 1710 if (phm->obj_index < 2) 1711 ret = 1; 1712 break; 1713 case HPI_OBJ_PROFILE: 1714 ret = phm->obj_index; 1715 break; 1716 default: 1717 break; 1718 } 1719 return ret; 1720 } 1721 1722 /** Complete transaction with DSP 1723 1724 Send message, get response, send or get stream data if any. 1725 */ 1726 static void hw_message(struct hpi_adapter_obj *pao, struct hpi_message *phm, 1727 struct hpi_response *phr) 1728 { 1729 u16 error = 0; 1730 u16 dsp_index = 0; 1731 struct hpi_hw_obj *phw = pao->priv; 1732 u16 num_dsp = phw->num_dsp; 1733 1734 if (num_dsp < 2) 1735 dsp_index = 0; 1736 else { 1737 dsp_index = get_dsp_index(pao, phm); 1738 1739 /* is this checked on the DSP anyway? */ 1740 if ((phm->function == HPI_ISTREAM_GROUP_ADD) 1741 || (phm->function == HPI_OSTREAM_GROUP_ADD)) { 1742 struct hpi_message hm; 1743 u16 add_index; 1744 hm.obj_index = phm->u.d.u.stream.stream_index; 1745 hm.object = phm->u.d.u.stream.object_type; 1746 add_index = get_dsp_index(pao, &hm); 1747 if (add_index != dsp_index) { 1748 phr->error = HPI_ERROR_NO_INTERDSP_GROUPS; 1749 return; 1750 } 1751 } 1752 } 1753 1754 hpios_dsplock_lock(pao); 1755 error = hpi6000_message_response_sequence(pao, dsp_index, phm, phr); 1756 1757 if (error) /* something failed in the HPI/DSP interface */ 1758 goto err; 1759 1760 if (phr->error) /* something failed in the DSP */ 1761 goto out; 1762 1763 switch (phm->function) { 1764 case HPI_OSTREAM_WRITE: 1765 case HPI_ISTREAM_ANC_WRITE: 1766 error = hpi6000_send_data(pao, dsp_index, phm, phr); 1767 break; 1768 case HPI_ISTREAM_READ: 1769 case HPI_OSTREAM_ANC_READ: 1770 error = hpi6000_get_data(pao, dsp_index, phm, phr); 1771 break; 1772 case HPI_ADAPTER_GET_ASSERT: 1773 phr->u.ax.assert.dsp_index = 0; /* dsp 0 default */ 1774 if (num_dsp == 2) { 1775 if (!phr->u.ax.assert.count) { 1776 /* no assert from dsp 0, check dsp 1 */ 1777 error = hpi6000_message_response_sequence(pao, 1778 1, phm, phr); 1779 phr->u.ax.assert.dsp_index = 1; 1780 } 1781 } 1782 } 1783 1784 err: 1785 if (error) { 1786 if (error >= HPI_ERROR_BACKEND_BASE) { 1787 phr->error = HPI_ERROR_DSP_COMMUNICATION; 1788 phr->specific_error = error; 1789 } else { 1790 phr->error = error; 1791 } 1792 1793 /* just the header of the response is valid */ 1794 phr->size = sizeof(struct hpi_response_header); 1795 } 1796 out: 1797 hpios_dsplock_unlock(pao); 1798 return; 1799 } 1800