1 #ifndef SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED 2 #define SOUND_FIREWIRE_DICE_INTERFACE_H_INCLUDED 3 4 /* 5 * DICE device interface definitions 6 */ 7 8 /* 9 * Generally, all registers can be read like memory, i.e., with quadlet read or 10 * block read transactions with at least quadlet-aligned offset and length. 11 * Writes are not allowed except where noted; quadlet-sized registers must be 12 * written with a quadlet write transaction. 13 * 14 * All values are in big endian. The DICE firmware runs on a little-endian CPU 15 * and just byte-swaps _all_ quadlets on the bus, so values without endianness 16 * (e.g. strings) get scrambled and must be byte-swapped again by the driver. 17 */ 18 19 /* 20 * Streaming is handled by the "DICE driver" interface. Its registers are 21 * located in this private address space. 22 */ 23 #define DICE_PRIVATE_SPACE 0xffffe0000000uLL 24 25 /* 26 * The registers are organized in several sections, which are organized 27 * separately to allow them to be extended individually. Whether a register is 28 * supported can be detected by checking its offset against its section's size. 29 * 30 * The section offset values are relative to DICE_PRIVATE_SPACE; the offset/ 31 * size values are measured in quadlets. Read-only. 32 */ 33 #define DICE_GLOBAL_OFFSET 0x00 34 #define DICE_GLOBAL_SIZE 0x04 35 #define DICE_TX_OFFSET 0x08 36 #define DICE_TX_SIZE 0x0c 37 #define DICE_RX_OFFSET 0x10 38 #define DICE_RX_SIZE 0x14 39 #define DICE_EXT_SYNC_OFFSET 0x18 40 #define DICE_EXT_SYNC_SIZE 0x1c 41 #define DICE_UNUSED2_OFFSET 0x20 42 #define DICE_UNUSED2_SIZE 0x24 43 44 /* 45 * Global settings. 46 */ 47 48 /* 49 * Stores the full 64-bit address (node ID and offset in the node's address 50 * space) where the device will send notifications. Must be changed with 51 * a compare/swap transaction by the owner. This register is automatically 52 * cleared on a bus reset. 53 */ 54 #define GLOBAL_OWNER 0x000 55 #define OWNER_NO_OWNER 0xffff000000000000uLL 56 #define OWNER_NODE_SHIFT 48 57 58 /* 59 * A bitmask with asynchronous events; read-only. When any event(s) happen, 60 * the bits of previous events are cleared, and the value of this register is 61 * also written to the address stored in the owner register. 62 */ 63 #define GLOBAL_NOTIFICATION 0x008 64 /* Some registers in the Rx/Tx sections may have changed. */ 65 #define NOTIFY_RX_CFG_CHG 0x00000001 66 #define NOTIFY_TX_CFG_CHG 0x00000002 67 /* Lock status of the current clock source may have changed. */ 68 #define NOTIFY_LOCK_CHG 0x00000010 69 /* Write to the clock select register has been finished. */ 70 #define NOTIFY_CLOCK_ACCEPTED 0x00000020 71 /* Lock status of some clock source has changed. */ 72 #define NOTIFY_EXT_STATUS 0x00000040 73 /* Other bits may be used for device-specific events. */ 74 75 /* 76 * A name that can be customized for each device; read/write. Padded with zero 77 * bytes. Quadlets are byte-swapped. The encoding is whatever the host driver 78 * happens to be using. 79 */ 80 #define GLOBAL_NICK_NAME 0x00c 81 #define NICK_NAME_SIZE 64 82 83 /* 84 * The current sample rate and clock source; read/write. Whether a clock 85 * source or sample rate is supported is device-specific; the internal clock 86 * source is always available. Low/mid/high = up to 48/96/192 kHz. This 87 * register can be changed even while streams are running. 88 */ 89 #define GLOBAL_CLOCK_SELECT 0x04c 90 #define CLOCK_SOURCE_MASK 0x000000ff 91 #define CLOCK_SOURCE_AES1 0x00000000 92 #define CLOCK_SOURCE_AES2 0x00000001 93 #define CLOCK_SOURCE_AES3 0x00000002 94 #define CLOCK_SOURCE_AES4 0x00000003 95 #define CLOCK_SOURCE_AES_ANY 0x00000004 96 #define CLOCK_SOURCE_ADAT 0x00000005 97 #define CLOCK_SOURCE_TDIF 0x00000006 98 #define CLOCK_SOURCE_WC 0x00000007 99 #define CLOCK_SOURCE_ARX1 0x00000008 100 #define CLOCK_SOURCE_ARX2 0x00000009 101 #define CLOCK_SOURCE_ARX3 0x0000000a 102 #define CLOCK_SOURCE_ARX4 0x0000000b 103 #define CLOCK_SOURCE_INTERNAL 0x0000000c 104 #define CLOCK_RATE_MASK 0x0000ff00 105 #define CLOCK_RATE_32000 0x00000000 106 #define CLOCK_RATE_44100 0x00000100 107 #define CLOCK_RATE_48000 0x00000200 108 #define CLOCK_RATE_88200 0x00000300 109 #define CLOCK_RATE_96000 0x00000400 110 #define CLOCK_RATE_176400 0x00000500 111 #define CLOCK_RATE_192000 0x00000600 112 #define CLOCK_RATE_ANY_LOW 0x00000700 113 #define CLOCK_RATE_ANY_MID 0x00000800 114 #define CLOCK_RATE_ANY_HIGH 0x00000900 115 #define CLOCK_RATE_NONE 0x00000a00 116 #define CLOCK_RATE_SHIFT 8 117 118 /* 119 * Enable streaming; read/write. Writing a non-zero value (re)starts all 120 * streams that have a valid iso channel set; zero stops all streams. The 121 * streams' parameters must be configured before starting. This register is 122 * automatically cleared on a bus reset. 123 */ 124 #define GLOBAL_ENABLE 0x050 125 126 /* 127 * Status of the sample clock; read-only. 128 */ 129 #define GLOBAL_STATUS 0x054 130 /* The current clock source is locked. */ 131 #define STATUS_SOURCE_LOCKED 0x00000001 132 /* The actual sample rate; CLOCK_RATE_32000-_192000 or _NONE. */ 133 #define STATUS_NOMINAL_RATE_MASK 0x0000ff00 134 135 /* 136 * Status of all clock sources; read-only. 137 */ 138 #define GLOBAL_EXTENDED_STATUS 0x058 139 /* 140 * The _LOCKED bits always show the current status; any change generates 141 * a notification. 142 */ 143 #define EXT_STATUS_AES1_LOCKED 0x00000001 144 #define EXT_STATUS_AES2_LOCKED 0x00000002 145 #define EXT_STATUS_AES3_LOCKED 0x00000004 146 #define EXT_STATUS_AES4_LOCKED 0x00000008 147 #define EXT_STATUS_ADAT_LOCKED 0x00000010 148 #define EXT_STATUS_TDIF_LOCKED 0x00000020 149 #define EXT_STATUS_ARX1_LOCKED 0x00000040 150 #define EXT_STATUS_ARX2_LOCKED 0x00000080 151 #define EXT_STATUS_ARX3_LOCKED 0x00000100 152 #define EXT_STATUS_ARX4_LOCKED 0x00000200 153 #define EXT_STATUS_WC_LOCKED 0x00000400 154 /* 155 * The _SLIP bits do not generate notifications; a set bit indicates that an 156 * error occurred since the last time when this register was read with 157 * a quadlet read transaction. 158 */ 159 #define EXT_STATUS_AES1_SLIP 0x00010000 160 #define EXT_STATUS_AES2_SLIP 0x00020000 161 #define EXT_STATUS_AES3_SLIP 0x00040000 162 #define EXT_STATUS_AES4_SLIP 0x00080000 163 #define EXT_STATUS_ADAT_SLIP 0x00100000 164 #define EXT_STATUS_TDIF_SLIP 0x00200000 165 #define EXT_STATUS_ARX1_SLIP 0x00400000 166 #define EXT_STATUS_ARX2_SLIP 0x00800000 167 #define EXT_STATUS_ARX3_SLIP 0x01000000 168 #define EXT_STATUS_ARX4_SLIP 0x02000000 169 #define EXT_STATUS_WC_SLIP 0x04000000 170 171 /* 172 * The measured rate of the current clock source, in Hz; read-only. 173 */ 174 #define GLOBAL_SAMPLE_RATE 0x05c 175 176 /* 177 * The version of the DICE driver specification that this device conforms to; 178 * read-only. 179 */ 180 #define GLOBAL_VERSION 0x060 181 182 /* Some old firmware versions do not have the following global registers: */ 183 184 /* 185 * Supported sample rates and clock sources; read-only. 186 */ 187 #define GLOBAL_CLOCK_CAPABILITIES 0x064 188 #define CLOCK_CAP_RATE_32000 0x00000001 189 #define CLOCK_CAP_RATE_44100 0x00000002 190 #define CLOCK_CAP_RATE_48000 0x00000004 191 #define CLOCK_CAP_RATE_88200 0x00000008 192 #define CLOCK_CAP_RATE_96000 0x00000010 193 #define CLOCK_CAP_RATE_176400 0x00000020 194 #define CLOCK_CAP_RATE_192000 0x00000040 195 #define CLOCK_CAP_SOURCE_AES1 0x00010000 196 #define CLOCK_CAP_SOURCE_AES2 0x00020000 197 #define CLOCK_CAP_SOURCE_AES3 0x00040000 198 #define CLOCK_CAP_SOURCE_AES4 0x00080000 199 #define CLOCK_CAP_SOURCE_AES_ANY 0x00100000 200 #define CLOCK_CAP_SOURCE_ADAT 0x00200000 201 #define CLOCK_CAP_SOURCE_TDIF 0x00400000 202 #define CLOCK_CAP_SOURCE_WC 0x00800000 203 #define CLOCK_CAP_SOURCE_ARX1 0x01000000 204 #define CLOCK_CAP_SOURCE_ARX2 0x02000000 205 #define CLOCK_CAP_SOURCE_ARX3 0x04000000 206 #define CLOCK_CAP_SOURCE_ARX4 0x08000000 207 #define CLOCK_CAP_SOURCE_INTERNAL 0x10000000 208 209 /* 210 * Names of all clock sources; read-only. Quadlets are byte-swapped. Names 211 * are separated with one backslash, the list is terminated with two 212 * backslashes. Unused clock sources are included. 213 */ 214 #define GLOBAL_CLOCK_SOURCE_NAMES 0x068 215 #define CLOCK_SOURCE_NAMES_SIZE 256 216 217 /* 218 * Capture stream settings. This section includes the number/size registers 219 * and the registers of all streams. 220 */ 221 222 /* 223 * The number of supported capture streams; read-only. 224 */ 225 #define TX_NUMBER 0x000 226 227 /* 228 * The size of one stream's register block, in quadlets; read-only. The 229 * registers of the first stream follow immediately afterwards; the registers 230 * of the following streams are offset by this register's value. 231 */ 232 #define TX_SIZE 0x004 233 234 /* 235 * The isochronous channel number on which packets are sent, or -1 if the 236 * stream is not to be used; read/write. 237 */ 238 #define TX_ISOCHRONOUS 0x008 239 240 /* 241 * The number of audio channels; read-only. There will be one quadlet per 242 * channel; the first channel is the first quadlet in a data block. 243 */ 244 #define TX_NUMBER_AUDIO 0x00c 245 246 /* 247 * The number of MIDI ports, 0-8; read-only. If > 0, there will be one 248 * additional quadlet in each data block, following the audio quadlets. 249 */ 250 #define TX_NUMBER_MIDI 0x010 251 252 /* 253 * The speed at which the packets are sent, SCODE_100-_400; read/write. 254 * SCODE_800 is only available in Dice III. 255 */ 256 #define TX_SPEED 0x014 257 258 /* 259 * Names of all audio channels; read-only. Quadlets are byte-swapped. Names 260 * are separated with one backslash, the list is terminated with two 261 * backslashes. 262 */ 263 #define TX_NAMES 0x018 264 #define TX_NAMES_SIZE 256 265 266 /* 267 * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio 268 * channel. 269 */ 270 #define TX_AC3_CAPABILITIES 0x118 271 272 /* 273 * Send audio data with IEC60958 label; read/write. Bitmask with one bit per 274 * audio channel. This register can be changed even while the stream is 275 * running. 276 */ 277 #define TX_AC3_ENABLE 0x11c 278 279 /* 280 * Playback stream settings. This section includes the number/size registers 281 * and the registers of all streams. 282 */ 283 284 /* 285 * The number of supported playback streams; read-only. 286 */ 287 #define RX_NUMBER 0x000 288 289 /* 290 * The size of one stream's register block, in quadlets; read-only. The 291 * registers of the first stream follow immediately afterwards; the registers 292 * of the following streams are offset by this register's value. 293 */ 294 #define RX_SIZE 0x004 295 296 /* 297 * The isochronous channel number on which packets are received, or -1 if the 298 * stream is not to be used; read/write. 299 */ 300 #define RX_ISOCHRONOUS 0x008 301 302 /* 303 * Index of first quadlet to be interpreted; read/write. If > 0, that many 304 * quadlets at the beginning of each data block will be ignored, and all the 305 * audio and MIDI quadlets will follow. 306 */ 307 #define RX_SEQ_START 0x00c 308 309 /* 310 * The number of audio channels; read-only. There will be one quadlet per 311 * channel. 312 */ 313 #define RX_NUMBER_AUDIO 0x010 314 315 /* 316 * The number of MIDI ports, 0-8; read-only. If > 0, there will be one 317 * additional quadlet in each data block, following the audio quadlets. 318 */ 319 #define RX_NUMBER_MIDI 0x014 320 321 /* 322 * Names of all audio channels; read-only. Quadlets are byte-swapped. Names 323 * are separated with one backslash, the list is terminated with two 324 * backslashes. 325 */ 326 #define RX_NAMES 0x018 327 #define RX_NAMES_SIZE 256 328 329 /* 330 * Audio IEC60958 capabilities; read-only. Bitmask with one bit per audio 331 * channel. 332 */ 333 #define RX_AC3_CAPABILITIES 0x118 334 335 /* 336 * Receive audio data with IEC60958 label; read/write. Bitmask with one bit 337 * per audio channel. This register can be changed even while the stream is 338 * running. 339 */ 340 #define RX_AC3_ENABLE 0x11c 341 342 /* 343 * Extended synchronization information. 344 * This section can be read completely with a block read request. 345 */ 346 347 /* 348 * Current clock source; read-only. 349 */ 350 #define EXT_SYNC_CLOCK_SOURCE 0x000 351 352 /* 353 * Clock source is locked (boolean); read-only. 354 */ 355 #define EXT_SYNC_LOCKED 0x004 356 357 /* 358 * Current sample rate (CLOCK_RATE_* >> CLOCK_RATE_SHIFT), _32000-_192000 or 359 * _NONE; read-only. 360 */ 361 #define EXT_SYNC_RATE 0x008 362 363 /* 364 * ADAT user data bits; read-only. 365 */ 366 #define EXT_SYNC_ADAT_USER_DATA 0x00c 367 /* The data bits, if available. */ 368 #define ADAT_USER_DATA_MASK 0x0f 369 /* The data bits are not available. */ 370 #define ADAT_USER_DATA_NO_DATA 0x10 371 372 #endif 373