1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2020, Linaro Ltd. 4 */ 5 6/dts-v1/; 7 8#include <dt-bindings/leds/common.h> 9#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 10#include <dt-bindings/sound/qcom,q6afe.h> 11#include <dt-bindings/sound/qcom,q6asm.h> 12#include "sm8250.dtsi" 13#include "pm8150.dtsi" 14#include "pm8150b.dtsi" 15#include "pm8150l.dtsi" 16 17/ { 18 model = "Qualcomm Technologies, Inc. Robotics RB5"; 19 compatible = "qcom,qrb5165-rb5", "qcom,sm8250"; 20 qcom,msm-id = <455 0x20001>; 21 qcom,board-id = <11 3>; 22 23 aliases { 24 serial0 = &uart12; 25 sdhc2 = &sdhc_2; 26 }; 27 28 chosen { 29 stdout-path = "serial0:115200n8"; 30 }; 31 32 /* Fixed crystal oscillator dedicated to MCP2518FD */ 33 clk40M: can-clock { 34 compatible = "fixed-clock"; 35 #clock-cells = <0>; 36 clock-frequency = <40000000>; 37 }; 38 39 dc12v: dc12v-regulator { 40 compatible = "regulator-fixed"; 41 regulator-name = "DC12V"; 42 regulator-min-microvolt = <12000000>; 43 regulator-max-microvolt = <12000000>; 44 regulator-always-on; 45 }; 46 47 hdmi-out { 48 compatible = "hdmi-connector"; 49 type = "a"; 50 51 port { 52 hdmi_con: endpoint { 53 remote-endpoint = <<9611_out>; 54 }; 55 }; 56 }; 57 58 leds { 59 compatible = "gpio-leds"; 60 61 led-user4 { 62 label = "green:user4"; 63 function = LED_FUNCTION_INDICATOR; 64 color = <LED_COLOR_ID_GREEN>; 65 gpios = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; 66 linux,default-trigger = "panic-indicator"; 67 default-state = "off"; 68 }; 69 70 led-wlan { 71 label = "yellow:wlan"; 72 function = LED_FUNCTION_WLAN; 73 color = <LED_COLOR_ID_YELLOW>; 74 gpios = <&pm8150_gpios 9 GPIO_ACTIVE_HIGH>; 75 linux,default-trigger = "phy0tx"; 76 default-state = "off"; 77 }; 78 79 led-bt { 80 label = "blue:bt"; 81 function = LED_FUNCTION_BLUETOOTH; 82 color = <LED_COLOR_ID_BLUE>; 83 gpios = <&pm8150_gpios 7 GPIO_ACTIVE_HIGH>; 84 linux,default-trigger = "bluetooth-power"; 85 default-state = "off"; 86 }; 87 }; 88 89 lt9611_1v2: lt9611-vdd12-regulator { 90 compatible = "regulator-fixed"; 91 regulator-name = "LT9611_1V2"; 92 93 vin-supply = <&vdc_3v3>; 94 regulator-min-microvolt = <1200000>; 95 regulator-max-microvolt = <1200000>; 96 }; 97 98 lt9611_3v3: lt9611-3v3 { 99 compatible = "regulator-fixed"; 100 regulator-name = "LT9611_3V3"; 101 102 vin-supply = <&vdc_3v3>; 103 regulator-min-microvolt = <3300000>; 104 regulator-max-microvolt = <3300000>; 105 regulator-boot-on; 106 regulator-always-on; 107 }; 108 109 thermal-zones { 110 conn-thermal { 111 polling-delay-passive = <0>; 112 polling-delay = <0>; 113 thermal-sensors = <&pm8150b_adc_tm 0>; 114 115 trips { 116 active-config0 { 117 temperature = <125000>; 118 hysteresis = <1000>; 119 type = "critical"; 120 }; 121 }; 122 }; 123 124 pm8150l-thermal { 125 polling-delay-passive = <0>; 126 polling-delay = <0>; 127 thermal-sensors = <&pm8150l_adc_tm 1>; 128 129 trips { 130 active-config0 { 131 temperature = <50000>; 132 hysteresis = <4000>; 133 type = "passive"; 134 }; 135 }; 136 }; 137 138 skin-msm-thermal { 139 polling-delay-passive = <0>; 140 polling-delay = <0>; 141 thermal-sensors = <&pm8150l_adc_tm 0>; 142 143 trips { 144 active-config0 { 145 temperature = <50000>; 146 hysteresis = <4000>; 147 type = "passive"; 148 }; 149 }; 150 }; 151 152 wifi-thermal { 153 polling-delay-passive = <0>; 154 polling-delay = <0>; 155 thermal-sensors = <&pm8150_adc_tm 1>; 156 157 trips { 158 active-config0 { 159 temperature = <52000>; 160 hysteresis = <4000>; 161 type = "passive"; 162 }; 163 }; 164 }; 165 166 xo-thermal { 167 polling-delay-passive = <0>; 168 polling-delay = <0>; 169 thermal-sensors = <&pm8150_adc_tm 0>; 170 171 trips { 172 active-config0 { 173 temperature = <50000>; 174 hysteresis = <4000>; 175 type = "passive"; 176 }; 177 }; 178 }; 179 }; 180 181 vbat: vbat-regulator { 182 compatible = "regulator-fixed"; 183 regulator-name = "VBAT"; 184 vin-supply = <&vreg_l11c_3p3>; 185 regulator-min-microvolt = <4200000>; 186 regulator-max-microvolt = <4200000>; 187 regulator-always-on; 188 }; 189 190 vbat_som: vbat-som-regulator { 191 compatible = "regulator-fixed"; 192 regulator-name = "VBAT_SOM"; 193 vin-supply = <&dc12v>; 194 regulator-min-microvolt = <4200000>; 195 regulator-max-microvolt = <4200000>; 196 regulator-always-on; 197 }; 198 199 vdc_3v3: vdc-3v3-regulator { 200 compatible = "regulator-fixed"; 201 regulator-name = "VDC_3V3"; 202 vin-supply = <&vreg_l11c_3p3>; 203 regulator-min-microvolt = <3300000>; 204 regulator-max-microvolt = <3300000>; 205 regulator-always-on; 206 }; 207 208 vdc_5v: vdc-5v-regulator { 209 compatible = "regulator-fixed"; 210 regulator-name = "VDC_5V"; 211 212 regulator-min-microvolt = <5000000>; 213 regulator-max-microvolt = <5000000>; 214 regulator-always-on; 215 vin-supply = <&vreg_l11c_3p3>; 216 }; 217 218 vph_pwr: vph-pwr-regulator { 219 compatible = "regulator-fixed"; 220 regulator-name = "vph_pwr"; 221 regulator-min-microvolt = <3700000>; 222 regulator-max-microvolt = <3700000>; 223 regulator-always-on; 224 }; 225 226 vreg_s4a_1p8: vreg-s4a-1p8 { 227 compatible = "regulator-fixed"; 228 regulator-name = "vreg_s4a_1p8"; 229 regulator-min-microvolt = <1800000>; 230 regulator-max-microvolt = <1800000>; 231 regulator-always-on; 232 }; 233}; 234 235&adsp { 236 status = "okay"; 237 firmware-name = "qcom/sm8250/adsp.mbn"; 238}; 239 240&apps_rsc { 241 pm8009-rpmh-regulators { 242 compatible = "qcom,pm8009-1-rpmh-regulators"; 243 qcom,pmic-id = "f"; 244 245 vdd-s1-supply = <&vph_pwr>; 246 vdd-s2-supply = <&vph_pwr>; 247 vdd-l2-supply = <&vreg_s8c_1p3>; 248 vdd-l5-l6-supply = <&vreg_bob>; 249 vdd-l7-supply = <&vreg_s4a_1p8>; 250 251 vreg_s2f_0p95: smps2 { 252 regulator-name = "vreg_s2f_0p95"; 253 regulator-min-microvolt = <900000>; 254 regulator-max-microvolt = <952000>; 255 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 256 }; 257 258 vreg_l1f_1p1: ldo1 { 259 regulator-name = "vreg_l1f_1p1"; 260 regulator-min-microvolt = <1104000>; 261 regulator-max-microvolt = <1104000>; 262 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 263 }; 264 265 vreg_l2f_1p2: ldo2 { 266 regulator-name = "vreg_l2f_1p2"; 267 regulator-min-microvolt = <1200000>; 268 regulator-max-microvolt = <1200000>; 269 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 270 }; 271 272 vreg_l6f_2p8: ldo6 { 273 regulator-name = "vreg_l6f_2p8"; 274 regulator-min-microvolt = <2800000>; 275 regulator-max-microvolt = <2800000>; 276 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 277 }; 278 279 vreg_l7f_1p8: ldo7 { 280 regulator-name = "vreg_l7f_1p8"; 281 regulator-min-microvolt = <1800000>; 282 regulator-max-microvolt = <1800000>; 283 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 284 }; 285 }; 286 287 pm8150-rpmh-regulators { 288 compatible = "qcom,pm8150-rpmh-regulators"; 289 qcom,pmic-id = "a"; 290 291 vdd-s1-supply = <&vph_pwr>; 292 vdd-s2-supply = <&vph_pwr>; 293 vdd-s3-supply = <&vph_pwr>; 294 vdd-s4-supply = <&vph_pwr>; 295 vdd-s5-supply = <&vph_pwr>; 296 vdd-s6-supply = <&vph_pwr>; 297 vdd-s7-supply = <&vph_pwr>; 298 vdd-s8-supply = <&vph_pwr>; 299 vdd-s9-supply = <&vph_pwr>; 300 vdd-s10-supply = <&vph_pwr>; 301 vdd-l2-l10-supply = <&vreg_bob>; 302 vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>; 303 vdd-l6-l9-supply = <&vreg_s8c_1p3>; 304 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; 305 vdd-l13-l16-l17-supply = <&vreg_bob>; 306 307 vreg_l2a_3p1: ldo2 { 308 regulator-name = "vreg_l2a_3p1"; 309 regulator-min-microvolt = <3072000>; 310 regulator-max-microvolt = <3072000>; 311 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 312 }; 313 314 vreg_l3a_0p9: ldo3 { 315 regulator-name = "vreg_l3a_0p9"; 316 regulator-min-microvolt = <928000>; 317 regulator-max-microvolt = <932000>; 318 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 319 }; 320 321 vreg_l5a_0p88: ldo5 { 322 regulator-name = "vreg_l5a_0p88"; 323 regulator-min-microvolt = <880000>; 324 regulator-max-microvolt = <880000>; 325 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 326 }; 327 328 vreg_l6a_1p2: ldo6 { 329 regulator-name = "vreg_l6a_1p2"; 330 regulator-min-microvolt = <1200000>; 331 regulator-max-microvolt = <1200000>; 332 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 333 }; 334 335 vreg_l7a_1p7: ldo7 { 336 regulator-name = "vreg_l7a_1p7"; 337 regulator-min-microvolt = <1704000>; 338 regulator-max-microvolt = <1800000>; 339 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 340 }; 341 342 vreg_l9a_1p2: ldo9 { 343 regulator-name = "vreg_l9a_1p2"; 344 regulator-min-microvolt = <1200000>; 345 regulator-max-microvolt = <1200000>; 346 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 347 }; 348 349 vreg_l10a_1p8: ldo10 { 350 regulator-name = "vreg_l10a_1p8"; 351 regulator-min-microvolt = <1800000>; 352 regulator-max-microvolt = <1800000>; 353 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 354 }; 355 356 vreg_l12a_1p8: ldo12 { 357 regulator-name = "vreg_l12a_1p8"; 358 regulator-min-microvolt = <1800000>; 359 regulator-max-microvolt = <1800000>; 360 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 361 }; 362 363 vreg_l13a_ts_3p0: ldo13 { 364 regulator-name = "vreg_l13a_ts_3p0"; 365 regulator-min-microvolt = <3008000>; 366 regulator-max-microvolt = <3008000>; 367 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 368 }; 369 370 vreg_l14a_1p8: ldo14 { 371 regulator-name = "vreg_l14a_1p8"; 372 regulator-min-microvolt = <1800000>; 373 regulator-max-microvolt = <1880000>; 374 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 375 }; 376 377 vreg_l15a_1p8: ldo15 { 378 regulator-name = "vreg_l15a_1p8"; 379 regulator-min-microvolt = <1800000>; 380 regulator-max-microvolt = <1800000>; 381 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 382 }; 383 384 vreg_l16a_2p7: ldo16 { 385 regulator-name = "vreg_l16a_2p7"; 386 regulator-min-microvolt = <2704000>; 387 regulator-max-microvolt = <2960000>; 388 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 389 }; 390 391 vreg_l17a_3p0: ldo17 { 392 regulator-name = "vreg_l17a_3p0"; 393 regulator-min-microvolt = <2856000>; 394 regulator-max-microvolt = <3008000>; 395 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 396 }; 397 398 vreg_l18a_0p92: ldo18 { 399 regulator-name = "vreg_l18a_0p92"; 400 regulator-min-microvolt = <800000>; 401 regulator-max-microvolt = <912000>; 402 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 403 }; 404 405 vreg_s5a_1p9: smps5 { 406 regulator-name = "vreg_s5a_1p9"; 407 regulator-min-microvolt = <1904000>; 408 regulator-max-microvolt = <2000000>; 409 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 410 }; 411 412 vreg_s6a_0p95: smps6 { 413 regulator-name = "vreg_s6a_0p95"; 414 regulator-min-microvolt = <920000>; 415 regulator-max-microvolt = <1128000>; 416 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 417 }; 418 }; 419 420 pm8150l-rpmh-regulators { 421 compatible = "qcom,pm8150l-rpmh-regulators"; 422 qcom,pmic-id = "c"; 423 424 vdd-s1-supply = <&vph_pwr>; 425 vdd-s2-supply = <&vph_pwr>; 426 vdd-s3-supply = <&vph_pwr>; 427 vdd-s4-supply = <&vph_pwr>; 428 vdd-s5-supply = <&vph_pwr>; 429 vdd-s6-supply = <&vph_pwr>; 430 vdd-s7-supply = <&vph_pwr>; 431 vdd-s8-supply = <&vph_pwr>; 432 vdd-l1-l8-supply = <&vreg_s4a_1p8>; 433 vdd-l2-l3-supply = <&vreg_s8c_1p3>; 434 vdd-l4-l5-l6-supply = <&vreg_bob>; 435 vdd-l7-l11-supply = <&vreg_bob>; 436 vdd-l9-l10-supply = <&vreg_bob>; 437 vdd-bob-supply = <&vph_pwr>; 438 439 vreg_bob: bob { 440 regulator-name = "vreg_bob"; 441 regulator-min-microvolt = <3008000>; 442 regulator-max-microvolt = <4000000>; 443 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 444 }; 445 446 vreg_l1c_1p8: ldo1 { 447 regulator-name = "vreg_l1c_1p8"; 448 regulator-min-microvolt = <1800000>; 449 regulator-max-microvolt = <1800000>; 450 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 451 }; 452 453 vreg_l2c_1p2: ldo2 { 454 regulator-name = "vreg_l2c_1p2"; 455 regulator-min-microvolt = <1200000>; 456 regulator-max-microvolt = <1200000>; 457 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 458 }; 459 460 vreg_l3c_0p8: ldo3 { 461 regulator-name = "vreg_l3c_0p8"; 462 regulator-min-microvolt = <800000>; 463 regulator-max-microvolt = <800000>; 464 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 465 }; 466 467 vreg_l4c_1p7: ldo4 { 468 regulator-name = "vreg_l4c_1p7"; 469 regulator-min-microvolt = <1704000>; 470 regulator-max-microvolt = <2928000>; 471 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 472 }; 473 474 vreg_l5c_1p8: ldo5 { 475 regulator-name = "vreg_l5c_1p8"; 476 regulator-min-microvolt = <1800000>; 477 regulator-max-microvolt = <2928000>; 478 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 479 }; 480 481 vreg_l6c_2p96: ldo6 { 482 regulator-name = "vreg_l6c_2p96"; 483 regulator-min-microvolt = <1800000>; 484 regulator-max-microvolt = <2960000>; 485 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 486 }; 487 488 vreg_l7c_cam_vcm0_2p85: ldo7 { 489 regulator-name = "vreg_l7c_cam_vcm0_2p85"; 490 regulator-min-microvolt = <2856000>; 491 regulator-max-microvolt = <3104000>; 492 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 493 }; 494 495 vreg_l8c_1p8: ldo8 { 496 regulator-name = "vreg_l8c_1p8"; 497 regulator-min-microvolt = <1800000>; 498 regulator-max-microvolt = <1800000>; 499 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 500 }; 501 502 vreg_l9c_2p96: ldo9 { 503 regulator-name = "vreg_l9c_2p96"; 504 regulator-min-microvolt = <2704000>; 505 regulator-max-microvolt = <2960000>; 506 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 507 }; 508 509 vreg_l10c_3p0: ldo10 { 510 regulator-name = "vreg_l10c_3p0"; 511 regulator-min-microvolt = <3000000>; 512 regulator-max-microvolt = <3000000>; 513 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 514 }; 515 516 vreg_l11c_3p3: ldo11 { 517 regulator-name = "vreg_l11c_3p3"; 518 regulator-min-microvolt = <3296000>; 519 regulator-max-microvolt = <3296000>; 520 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 521 regulator-always-on; 522 }; 523 524 vreg_s8c_1p3: smps8 { 525 regulator-name = "vreg_s8c_1p3"; 526 regulator-min-microvolt = <1352000>; 527 regulator-max-microvolt = <1352000>; 528 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 529 }; 530 }; 531}; 532 533&cdsp { 534 status = "okay"; 535 firmware-name = "qcom/sm8250/cdsp.mbn"; 536}; 537 538&dsi0 { 539 status = "okay"; 540 vdda-supply = <&vreg_l9a_1p2>; 541 542#if 0 543 qcom,dual-dsi-mode; 544 qcom,master-dsi; 545#endif 546 547 ports { 548 port@1 { 549 endpoint { 550 remote-endpoint = <<9611_a>; 551 data-lanes = <0 1 2 3>; 552 }; 553 }; 554 }; 555}; 556 557&dsi0_phy { 558 status = "okay"; 559 vdds-supply = <&vreg_l5a_0p88>; 560}; 561 562&gmu { 563 status = "okay"; 564}; 565 566&gpu { 567 status = "okay"; 568 569 zap-shader { 570 memory-region = <&gpu_mem>; 571 firmware-name = "qcom/sm8250/a650_zap.mbn"; 572 }; 573}; 574 575/* LS-I2C0 */ 576&i2c4 { 577 status = "okay"; 578}; 579 580&i2c5 { 581 status = "okay"; 582 clock-frequency = <400000>; 583 584 lt9611_codec: hdmi-bridge@2b { 585 compatible = "lontium,lt9611uxc"; 586 reg = <0x2b>; 587 #sound-dai-cells = <1>; 588 589 interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>; 590 591 reset-gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_HIGH>; 592 593 vdd-supply = <<9611_1v2>; 594 vcc-supply = <<9611_3v3>; 595 596 pinctrl-names = "default"; 597 pinctrl-0 = <<9611_irq_pin <9611_rst_pin>; 598 599 ports { 600 #address-cells = <1>; 601 #size-cells = <0>; 602 603 port@0 { 604 reg = <0>; 605 606 lt9611_a: endpoint { 607 remote-endpoint = <&dsi0_out>; 608 }; 609 }; 610 611#if 0 612 port@1 { 613 reg = <1>; 614 615 lt9611_b: endpoint { 616 remote-endpoint = <&dsi1_out>; 617 }; 618 }; 619#endif 620 621 port@2 { 622 reg = <2>; 623 624 lt9611_out: endpoint { 625 remote-endpoint = <&hdmi_con>; 626 }; 627 }; 628 629 }; 630 }; 631}; 632 633/* LS-I2C1 */ 634&i2c15 { 635 status = "okay"; 636}; 637 638&mdss { 639 status = "okay"; 640}; 641 642&mdss_mdp { 643 status = "okay"; 644}; 645 646&pm8150_adc { 647 xo-therm@4c { 648 reg = <ADC5_XO_THERM_100K_PU>; 649 qcom,ratiometric; 650 qcom,hw-settle-time = <200>; 651 }; 652 653 wifi-therm@4e { 654 reg = <ADC5_AMUX_THM2_100K_PU>; 655 qcom,ratiometric; 656 qcom,hw-settle-time = <200>; 657 }; 658}; 659 660&pm8150_adc_tm { 661 status = "okay"; 662 663 xo-therm@0 { 664 reg = <0>; 665 io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>; 666 qcom,ratiometric; 667 qcom,hw-settle-time-us = <200>; 668 }; 669 670 wifi-therm@1 { 671 reg = <1>; 672 io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; 673 qcom,ratiometric; 674 qcom,hw-settle-time-us = <200>; 675 }; 676}; 677 678&pcie0 { 679 status = "okay"; 680}; 681 682&pcie0_phy { 683 status = "okay"; 684 vdda-phy-supply = <&vreg_l5a_0p88>; 685 vdda-pll-supply = <&vreg_l9a_1p2>; 686}; 687 688&pcie1 { 689 status = "okay"; 690}; 691 692&pcie1_phy { 693 status = "okay"; 694 vdda-phy-supply = <&vreg_l5a_0p88>; 695 vdda-pll-supply = <&vreg_l9a_1p2>; 696}; 697 698&pcie2 { 699 status = "okay"; 700}; 701 702&pcie2_phy { 703 status = "okay"; 704 vdda-phy-supply = <&vreg_l5a_0p88>; 705 vdda-pll-supply = <&vreg_l9a_1p2>; 706}; 707 708&pm8150_gpios { 709 gpio-reserved-ranges = <1 1>, <3 2>, <7 1>; 710 gpio-line-names = 711 "NC", 712 "OPTION2", 713 "PM_GPIO-F", 714 "PM_SLP_CLK_IN", 715 "OPTION1", 716 "VOL_UP_N", 717 "PM8250_GPIO7", /* Blue LED */ 718 "SP_ARI_PWR_ALARM", 719 "GPIO_9_P", /* Yellow LED */ 720 "GPIO_10_P"; /* Green LED */ 721}; 722 723&pm8150b_adc { 724 conn-therm@4f { 725 reg = <ADC5_AMUX_THM3_100K_PU>; 726 qcom,ratiometric; 727 qcom,hw-settle-time = <200>; 728 }; 729}; 730 731&pm8150b_adc_tm { 732 status = "okay"; 733 734 conn-therm@0 { 735 reg = <0>; 736 io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; 737 qcom,ratiometric; 738 qcom,hw-settle-time-us = <200>; 739 }; 740}; 741 742&pm8150b_gpios { 743 gpio-line-names = 744 "NC", 745 "NC", 746 "NC", 747 "NC", 748 "HAP_BOOST_EN", /* SOM */ 749 "SMB_STAT", /* SOM */ 750 "NC", 751 "NC", 752 "SDM_FORCE_USB_BOOT", 753 "NC", 754 "NC", 755 "NC"; 756}; 757 758&pm8150l_adc { 759 skin-msm-therm@4e { 760 reg = <ADC5_AMUX_THM2_100K_PU>; 761 qcom,ratiometric; 762 qcom,hw-settle-time = <200>; 763 }; 764 765 pm8150l-therm@4f { 766 reg = <ADC5_AMUX_THM3_100K_PU>; 767 qcom,ratiometric; 768 qcom,hw-settle-time = <200>; 769 }; 770}; 771 772&pm8150l_adc_tm { 773 status = "okay"; 774 775 skin-msm-therm@0 { 776 reg = <0>; 777 io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>; 778 qcom,ratiometric; 779 qcom,hw-settle-time-us = <200>; 780 }; 781 782 pm8150l-therm@1 { 783 reg = <1>; 784 io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; 785 qcom,ratiometric; 786 qcom,hw-settle-time-us = <200>; 787 }; 788}; 789 790&pm8150l_gpios { 791 gpio-line-names = 792 "NC", 793 "PM3003A_EN", 794 "NC", 795 "NC", 796 "PM_GPIO5", /* HDMI RST_N */ 797 "PM_GPIO-A", /* PWM */ 798 "PM_GPIO7", 799 "NC", 800 "NC", 801 "PM_GPIO-B", 802 "NC", 803 "PM3003A_MODE"; 804 805 lt9611_rst_pin: lt9611-rst-state { 806 pins = "gpio5"; 807 function = "normal"; 808 809 output-high; 810 input-disable; 811 power-source = <0>; 812 }; 813}; 814 815&pm8150l_lpg { 816 status = "okay"; 817 818 #address-cells = <1>; 819 #size-cells = <0>; 820 821 led@1 { 822 reg = <1>; 823 color = <LED_COLOR_ID_GREEN>; 824 function = LED_FUNCTION_HEARTBEAT; 825 function-enumerator = <3>; 826 827 linux,default-trigger = "heartbeat"; 828 default-state = "on"; 829 }; 830 831 led@2 { 832 reg = <2>; 833 color = <LED_COLOR_ID_GREEN>; 834 function = LED_FUNCTION_INDICATOR; 835 function-enumerator = <2>; 836 default-state = "on"; 837 }; 838 839 led@3 { 840 reg = <3>; 841 color = <LED_COLOR_ID_GREEN>; 842 function = LED_FUNCTION_INDICATOR; 843 function-enumerator = <1>; 844 }; 845}; 846 847&pon_pwrkey { 848 status = "okay"; 849}; 850 851&pon_resin { 852 status = "okay"; 853 854 linux,code = <KEY_VOLUMEDOWN>; 855}; 856 857&qupv3_id_0 { 858 status = "okay"; 859}; 860 861&qupv3_id_1 { 862 status = "okay"; 863}; 864 865&qupv3_id_2 { 866 status = "okay"; 867}; 868 869&q6afedai { 870 dai@16 { 871 reg = <PRIMARY_MI2S_RX>; 872 qcom,sd-lines = <0 1 2 3>; 873 }; 874}; 875 876/* TERT I2S Uses 1 I2S SD Lines for audio on LT9611 HDMI Bridge */ 877&q6afedai { 878 dai@20 { 879 reg = <TERTIARY_MI2S_RX>; 880 qcom,sd-lines = <0>; 881 }; 882}; 883 884&q6asmdai { 885 dai@0 { 886 reg = <0>; 887 }; 888 889 dai@1 { 890 reg = <1>; 891 }; 892 893 dai@2 { 894 reg = <2>; 895 }; 896}; 897 898&sdhc_2 { 899 status = "okay"; 900 pinctrl-names = "default"; 901 pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>; 902 vmmc-supply = <&vreg_l9c_2p96>; 903 vqmmc-supply = <&vreg_l6c_2p96>; 904 cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; 905 bus-width = <4>; 906 no-sdio; 907 no-mmc; 908}; 909 910&sound { 911 compatible = "qcom,qrb5165-rb5-sndcard"; 912 pinctrl-0 = <&tert_mi2s_active>; 913 pinctrl-names = "default"; 914 model = "Qualcomm-RB5-WSA8815-Speakers-DMIC0"; 915 audio-routing = 916 "SpkrLeft IN", "WSA_SPK1 OUT", 917 "SpkrRight IN", "WSA_SPK2 OUT", 918 "VA DMIC0", "vdd-micb", 919 "VA DMIC1", "vdd-micb", 920 "MM_DL1", "MultiMedia1 Playback", 921 "MM_DL2", "MultiMedia2 Playback", 922 "MultiMedia3 Capture", "MM_UL3"; 923 924 mm1-dai-link { 925 link-name = "MultiMedia1"; 926 cpu { 927 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; 928 }; 929 }; 930 931 mm2-dai-link { 932 link-name = "MultiMedia2"; 933 cpu { 934 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; 935 }; 936 }; 937 938 mm3-dai-link { 939 link-name = "MultiMedia3"; 940 cpu { 941 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; 942 }; 943 }; 944 945 hdmi-dai-link { 946 link-name = "HDMI Playback"; 947 cpu { 948 sound-dai = <&q6afedai TERTIARY_MI2S_RX>; 949 }; 950 951 platform { 952 sound-dai = <&q6routing>; 953 }; 954 955 codec { 956 sound-dai = <<9611_codec 0>; 957 }; 958 }; 959 960 dma-dai-link { 961 link-name = "WSA Playback"; 962 cpu { 963 sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>; 964 }; 965 966 platform { 967 sound-dai = <&q6routing>; 968 }; 969 970 codec { 971 sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; 972 }; 973 }; 974 975 va-dai-link { 976 link-name = "VA Capture"; 977 cpu { 978 sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>; 979 }; 980 981 platform { 982 sound-dai = <&q6routing>; 983 }; 984 985 codec { 986 sound-dai = <&vamacro 0>; 987 }; 988 }; 989}; 990 991/* CAN */ 992&spi0 { 993 status = "okay"; 994 pinctrl-names = "default"; 995 pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs_gpio>; 996 cs-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>; 997 998 can@0 { 999 compatible = "microchip,mcp2518fd"; 1000 reg = <0>; 1001 clocks = <&clk40M>; 1002 interrupts-extended = <&tlmm 15 IRQ_TYPE_LEVEL_LOW>; 1003 spi-max-frequency = <10000000>; 1004 vdd-supply = <&vdc_5v>; 1005 xceiver-supply = <&vdc_5v>; 1006 }; 1007}; 1008 1009&swr0 { 1010 status = "okay"; 1011 1012 left_spkr: speaker@0,3 { 1013 compatible = "sdw10217211000"; 1014 reg = <0 3>; 1015 powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; 1016 #thermal-sensor-cells = <0>; 1017 sound-name-prefix = "SpkrLeft"; 1018 #sound-dai-cells = <0>; 1019 }; 1020 1021 right_spkr: speaker@0,4 { 1022 compatible = "sdw10217211000"; 1023 reg = <0 4>; 1024 powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; 1025 #thermal-sensor-cells = <0>; 1026 sound-name-prefix = "SpkrRight"; 1027 #sound-dai-cells = <0>; 1028 }; 1029}; 1030 1031&tlmm { 1032 gpio-reserved-ranges = <40 4>; 1033 gpio-line-names = 1034 "GPIO-MM", 1035 "GPIO-NN", 1036 "GPIO-OO", 1037 "GPIO-PP", 1038 "GPIO-A", 1039 "GPIO-C", 1040 "GPIO-E", 1041 "GPIO-D", 1042 "I2C0-SDA", 1043 "I2C0-SCL", 1044 "GPIO-TT", /* GPIO_10 */ 1045 "NC", 1046 "GPIO_12_I2C_SDA", 1047 "GPIO_13_I2C_SCL", 1048 "GPIO-X", 1049 "GPIO_15_RGMII_INT", 1050 "HST_BT_UART_CTS", 1051 "HST_BT_UART_RFR", 1052 "HST_BT_UART_TX", 1053 "HST_BT_UART_RX", 1054 "HST_WLAN_EN", /* GPIO_20 */ 1055 "HST_BT_EN", 1056 "GPIO-AAA", 1057 "GPIO-BBB", 1058 "GPIO-CCC", 1059 "GPIO-Z", 1060 "GPIO-DDD", 1061 "GPIO-BB", 1062 "GPIO_28_CAN_SPI_MISO", 1063 "GPIO_29_CAN_SPI_MOSI", 1064 "GPIO_30_CAN_SPI_CLK", /* GPIO_30 */ 1065 "GPIO_31_CAN_SPI_CS", 1066 "GPIO-UU", 1067 "NC", 1068 "UART1_TXD_SOM", 1069 "UART1_RXD_SOM", 1070 "UART0_CTS", 1071 "UART0_RTS", 1072 "UART0_TXD", 1073 "UART0_RXD", 1074 "SPI1_MISO", /* GPIO_40 */ 1075 "SPI1_MOSI", 1076 "SPI1_CLK", 1077 "SPI1_CS", 1078 "I2C1_SDA", 1079 "I2C1_SCL", 1080 "GPIO-F", 1081 "GPIO-JJ", 1082 "Board_ID1", 1083 "Board_ID2", 1084 "NC", /* GPIO_50 */ 1085 "NC", 1086 "SPI0_MISO", 1087 "SPI0_MOSI", 1088 "SPI0_SCLK", 1089 "SPI0_CS", 1090 "GPIO-QQ", 1091 "GPIO-RR", 1092 "USB2LAN_RESET", 1093 "USB2LAN_EXTWAKE", 1094 "NC", /* GPIO_60 */ 1095 "NC", 1096 "NC", 1097 "LT9611_INT", 1098 "GPIO-AA", 1099 "USB_CC_DIR", 1100 "GPIO-G", 1101 "GPIO-LL", 1102 "USB_DP_HPD_1P8", 1103 "NC", 1104 "NC", /* GPIO_70 */ 1105 "SD_CMD", 1106 "SD_DAT3", 1107 "SD_SCLK", 1108 "SD_DAT2", 1109 "SD_DAT1", 1110 "SD_DAT0", /* BOOT_CFG3 */ 1111 "SD_UFS_CARD_DET_N", 1112 "GPIO-II", 1113 "PCIE0_RST_N", 1114 "PCIE0_CLK_REQ_N", /* GPIO_80 */ 1115 "PCIE0_WAKE_N", 1116 "GPIO-CC", 1117 "GPIO-DD", 1118 "GPIO-EE", 1119 "GPIO-FF", 1120 "GPIO-GG", 1121 "GPIO-HH", 1122 "GPIO-VV", 1123 "GPIO-WW", 1124 "NC", /* GPIO_90 */ 1125 "NC", 1126 "GPIO-K", 1127 "GPIO-I", 1128 "CSI0_MCLK", 1129 "CSI1_MCLK", 1130 "CSI2_MCLK", 1131 "CSI3_MCLK", 1132 "GPIO-AA", /* CSI4_MCLK */ 1133 "GPIO-BB", /* CSI5_MCLK */ 1134 "GPIO-KK", /* GPIO_100 */ 1135 "CCI_I2C_SDA0", 1136 "CCI_I2C_SCL0", 1137 "CCI_I2C_SDA1", 1138 "CCI_I2C_SCL1", 1139 "CCI_I2C_SDA2", 1140 "CCI_I2C_SCL2", 1141 "CCI_I2C_SDA3", 1142 "CCI_I2C_SCL3", 1143 "GPIO-L", 1144 "NC", /* GPIO_110 */ 1145 "NC", 1146 "ACCEL_INT", 1147 "GYRO_INT", 1148 "GPIO-J", 1149 "GPIO-YY", 1150 "GPIO-H", 1151 "GPIO-ZZ", 1152 "NC", 1153 "NC", 1154 "NC", /* GPIO_120 */ 1155 "NC", 1156 "MAG_INT", 1157 "MAG_DRDY_INT", 1158 "HST_SW_CTRL", 1159 "GPIO-M", 1160 "GPIO-N", 1161 "GPIO-O", 1162 "GPIO-P", 1163 "PS_INT", 1164 "WSA1_EN", /* GPIO_130 */ 1165 "USB_HUB_RESET", 1166 "SDM_FORCE_USB_BOOT", 1167 "I2S1_CLK_HDMI", 1168 "I2S1_DATA0_HDMI", 1169 "I2S1_WS_HDMI", 1170 "GPIO-B", 1171 "GPIO_137", /* To LT9611_I2S_MCLK_3V3 */ 1172 "PCM_CLK", 1173 "PCM_DI", 1174 "PCM_DO", /* GPIO_140 */ 1175 "PCM_FS", 1176 "HST_SLIM_CLK", 1177 "HST_SLIM_DATA", 1178 "GPIO-U", 1179 "GPIO-Y", 1180 "GPIO-R", 1181 "GPIO-Q", 1182 "GPIO-S", 1183 "GPIO-T", 1184 "GPIO-V", /* GPIO_150 */ 1185 "GPIO-W", 1186 "DMIC_CLK1", 1187 "DMIC_DATA1", 1188 "DMIC_CLK2", 1189 "DMIC_DATA2", 1190 "WSA_SWR_CLK", 1191 "WSA_SWR_DATA", 1192 "DMIC_CLK3", 1193 "DMIC_DATA3", 1194 "I2C4_SDA", /* GPIO_160 */ 1195 "I2C4_SCL", 1196 "SPI3_CS1", 1197 "SPI3_CS2", 1198 "SPI2_MISO_LS3", 1199 "SPI2_MOSI_LS3", 1200 "SPI2_CLK_LS3", 1201 "SPI2_ACCEL_CS_LS3", 1202 "SPI2_CS1", 1203 "NC", 1204 "GPIO-SS", /* GPIO_170 */ 1205 "GPIO-XX", 1206 "SPI3_MISO", 1207 "SPI3_MOSI", 1208 "SPI3_CLK", 1209 "SPI3_CS", 1210 "HST_BLE_SNS_UART_TX", 1211 "HST_BLE_SNS_UART_RX", 1212 "HST_WLAN_UART_TX", 1213 "HST_WLAN_UART_RX"; 1214 1215 lt9611_irq_pin: lt9611-irq-state { 1216 pins = "gpio63"; 1217 function = "gpio"; 1218 bias-disable; 1219 }; 1220 1221 sdc2_default_state: sdc2-default-state { 1222 clk-pins { 1223 pins = "sdc2_clk"; 1224 bias-disable; 1225 drive-strength = <16>; 1226 }; 1227 1228 cmd-pins { 1229 pins = "sdc2_cmd"; 1230 bias-pull-up; 1231 drive-strength = <10>; 1232 }; 1233 1234 data-pins { 1235 pins = "sdc2_data"; 1236 bias-pull-up; 1237 drive-strength = <10>; 1238 }; 1239 }; 1240 1241 sdc2_card_det_n: sd-card-det-n-state { 1242 pins = "gpio77"; 1243 function = "gpio"; 1244 bias-pull-up; 1245 }; 1246}; 1247 1248&uart12 { 1249 status = "okay"; 1250}; 1251 1252&ufs_mem_hc { 1253 status = "okay"; 1254 1255 vcc-supply = <&vreg_l17a_3p0>; 1256 vcc-max-microamp = <800000>; 1257 vccq-supply = <&vreg_l6a_1p2>; 1258 vccq-max-microamp = <800000>; 1259 vccq2-supply = <&vreg_s4a_1p8>; 1260 vccq2-max-microamp = <800000>; 1261}; 1262 1263&ufs_mem_phy { 1264 status = "okay"; 1265 1266 vdda-phy-supply = <&vreg_l5a_0p88>; 1267 vdda-pll-supply = <&vreg_l9a_1p2>; 1268}; 1269 1270&usb_1 { 1271 status = "okay"; 1272}; 1273 1274&usb_1_dwc3 { 1275 dr_mode = "peripheral"; 1276}; 1277 1278&usb_1_hsphy { 1279 status = "okay"; 1280 1281 vdda-pll-supply = <&vreg_l5a_0p88>; 1282 vdda33-supply = <&vreg_l2a_3p1>; 1283 vdda18-supply = <&vreg_l12a_1p8>; 1284}; 1285 1286&usb_1_qmpphy { 1287 status = "okay"; 1288 1289 vdda-phy-supply = <&vreg_l9a_1p2>; 1290 vdda-pll-supply = <&vreg_l18a_0p92>; 1291}; 1292 1293&usb_2 { 1294 status = "okay"; 1295}; 1296 1297&usb_2_dwc3 { 1298 dr_mode = "host"; 1299}; 1300 1301&usb_2_hsphy { 1302 status = "okay"; 1303 1304 vdda-pll-supply = <&vreg_l5a_0p88>; 1305 vdda33-supply = <&vreg_l2a_3p1>; 1306 vdda18-supply = <&vreg_l12a_1p8>; 1307}; 1308 1309&usb_2_qmpphy { 1310 status = "okay"; 1311 1312 vdda-phy-supply = <&vreg_l9a_1p2>; 1313 vdda-pll-supply = <&vreg_l18a_0p92>; 1314}; 1315 1316&vamacro { 1317 pinctrl-0 = <&dmic01_active>; 1318 pinctrl-names = "default"; 1319 vdd-micb-supply = <&vreg_s4a_1p8>; 1320 qcom,dmic-sample-rate = <600000>; 1321}; 1322 1323&venus { 1324 status = "okay"; 1325}; 1326 1327&wsamacro { 1328 status = "okay"; 1329}; 1330 1331/* PINCTRL - additions to nodes defined in sm8250.dtsi */ 1332&qup_spi0_cs_gpio { 1333 drive-strength = <6>; 1334 bias-disable; 1335}; 1336 1337&qup_spi0_data_clk { 1338 drive-strength = <6>; 1339 bias-disable; 1340}; 1341