xref: /openbmc/linux/scripts/dtc/include-prefixes/arm64/qcom/ipq6018.dtsi (revision bf74ee101d3403d72dac5997be083ac41028c66b)

// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
 * IPQ6018 SoC device tree source
 *
 * Copyright (c) 2019, The Linux Foundation. All rights reserved.
 */

#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
#include <dt-bindings/reset/qcom,gcc-ipq6018.h>
#include <dt-bindings/clock/qcom,apss-ipq.h>

/ {
	#address-cells = <2>;
	#size-cells = <2>;
	interrupt-parent = <&intc>;

	clocks {
		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			clock-frequency = <32000>;
			#clock-cells = <0>;
		};

		xo: xo {
			compatible = "fixed-clock";
			clock-frequency = <24000000>;
			#clock-cells = <0>;
		};
	};

	cpus: cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			reg = <0x0>;
			enable-method = "psci";
			next-level-cache = <&L2_0>;
			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
			clock-names = "cpu";
			operating-points-v2 = <&cpu_opp_table>;
			cpu-supply = <&ipq6018_s2>;
		};

		CPU1: cpu@1 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			enable-method = "psci";
			reg = <0x1>;
			next-level-cache = <&L2_0>;
			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
			clock-names = "cpu";
			operating-points-v2 = <&cpu_opp_table>;
			cpu-supply = <&ipq6018_s2>;
		};

		CPU2: cpu@2 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			enable-method = "psci";
			reg = <0x2>;
			next-level-cache = <&L2_0>;
			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
			clock-names = "cpu";
			operating-points-v2 = <&cpu_opp_table>;
			cpu-supply = <&ipq6018_s2>;
		};

		CPU3: cpu@3 {
			device_type = "cpu";
			compatible = "arm,cortex-a53";
			enable-method = "psci";
			reg = <0x3>;
			next-level-cache = <&L2_0>;
			clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
			clock-names = "cpu";
			operating-points-v2 = <&cpu_opp_table>;
			cpu-supply = <&ipq6018_s2>;
		};

		L2_0: l2-cache {
			compatible = "cache";
			cache-level = <2>;
			cache-unified;
		};
	};

	firmware {
		scm {
			compatible = "qcom,scm-ipq6018", "qcom,scm";
			qcom,dload-mode = <&tcsr 0x6100>;
		};
	};

	cpu_opp_table: opp-table-cpu {
		compatible = "operating-points-v2";
		opp-shared;

		opp-864000000 {
			opp-hz = /bits/ 64 <864000000>;
			opp-microvolt = <725000>;
			clock-latency-ns = <200000>;
		};

		opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-microvolt = <787500>;
			clock-latency-ns = <200000>;
		};

		opp-1320000000 {
			opp-hz = /bits/ 64 <1320000000>;
			opp-microvolt = <862500>;
			clock-latency-ns = <200000>;
		};

		opp-1440000000 {
			opp-hz = /bits/ 64 <1440000000>;
			opp-microvolt = <925000>;
			clock-latency-ns = <200000>;
		};

		opp-1608000000 {
			opp-hz = /bits/ 64 <1608000000>;
			opp-microvolt = <987500>;
			clock-latency-ns = <200000>;
		};

		opp-1800000000 {
			opp-hz = /bits/ 64 <1800000000>;
			opp-microvolt = <1062500>;
			clock-latency-ns = <200000>;
		};
	};

	pmuv8: pmu {
		compatible = "arm,cortex-a53-pmu";
		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
	};

	psci: psci {
		compatible = "arm,psci-1.0";
		method = "smc";
	};

	rpm: remoteproc {
		compatible = "qcom,ipq6018-rpm-proc", "qcom,rpm-proc";

		glink-edge {
			compatible = "qcom,glink-rpm";
			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
			qcom,rpm-msg-ram = <&rpm_msg_ram>;
			mboxes = <&apcs_glb 0>;

			rpm_requests: rpm-requests {
				compatible = "qcom,rpm-ipq6018";
				qcom,glink-channels = "rpm_requests";

				regulators {
					compatible = "qcom,rpm-mp5496-regulators";

					ipq6018_s2: s2 {
						regulator-min-microvolt = <725000>;
						regulator-max-microvolt = <1062500>;
						regulator-always-on;
					};
				};
			};
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		rpm_msg_ram: memory@60000 {
			reg = <0x0 0x00060000 0x0 0x6000>;
			no-map;
		};

		bootloader@4a100000 {
			reg = <0x0 0x4a100000 0x0 0x400000>;
			no-map;
		};

		sbl@4a500000 {
			reg = <0x0 0x4a500000 0x0 0x100000>;
			no-map;
		};

		tz: memory@4a600000 {
			reg = <0x0 0x4a600000 0x0 0x400000>;
			no-map;
		};

		smem_region: memory@4aa00000 {
			reg = <0x0 0x4aa00000 0x0 0x100000>;
			no-map;
		};

		q6_region: memory@4ab00000 {
			reg = <0x0 0x4ab00000 0x0 0x5500000>;
			no-map;
		};
	};

	smem {
		compatible = "qcom,smem";
		memory-region = <&smem_region>;
		hwlocks = <&tcsr_mutex 3>;
	};

	soc: soc@0 {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x0 0xffffffff>;
		dma-ranges;
		compatible = "simple-bus";

		qusb_phy_1: qusb@59000 {
			compatible = "qcom,ipq6018-qusb2-phy";
			reg = <0x0 0x00059000 0x0 0x180>;
			#phy-cells = <0>;

			clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
				 <&xo>;
			clock-names = "cfg_ahb", "ref";

			resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
			status = "disabled";
		};

		ssphy_0: ssphy@78000 {
			compatible = "qcom,ipq6018-qmp-usb3-phy";
			reg = <0x0 0x00078000 0x0 0x1c4>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_USB0_AUX_CLK>,
				 <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>;
			clock-names = "aux", "cfg_ahb", "ref";

			resets = <&gcc GCC_USB0_PHY_BCR>,
				 <&gcc GCC_USB3PHY_0_PHY_BCR>;
			reset-names = "phy","common";
			status = "disabled";

			usb0_ssphy: phy@78200 {
				reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
				      <0x0 0x00078400 0x0 0x200>, /* Rx */
				      <0x0 0x00078800 0x0 0x1f8>, /* PCS */
				      <0x0 0x00078600 0x0 0x044>; /* PCS misc */
				#phy-cells = <0>;
				#clock-cells = <0>;
				clocks = <&gcc GCC_USB0_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "gcc_usb0_pipe_clk_src";
			};
		};

		qusb_phy_0: qusb@79000 {
			compatible = "qcom,ipq6018-qusb2-phy";
			reg = <0x0 0x00079000 0x0 0x180>;
			#phy-cells = <0>;

			clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
				<&xo>;
			clock-names = "cfg_ahb", "ref";

			resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
			status = "disabled";
		};

		pcie_phy: phy@84000 {
			compatible = "qcom,ipq6018-qmp-pcie-phy";
			reg = <0x0 0x00084000 0x0 0x1bc>; /* Serdes PLL */
			status = "disabled";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_PCIE0_AUX_CLK>,
				<&gcc GCC_PCIE0_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";

			resets = <&gcc GCC_PCIE0_PHY_BCR>,
				<&gcc GCC_PCIE0PHY_PHY_BCR>;
			reset-names = "phy",
				      "common";

			pcie_phy0: phy@84200 {
				reg = <0x0 0x00084200 0x0 0x16c>, /* Serdes Tx */
				      <0x0 0x00084400 0x0 0x200>, /* Serdes Rx */
				      <0x0 0x00084800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */
				      <0x0 0x00084c00 0x0 0xf4>; /* pcs_misc */
				#phy-cells = <0>;

				clocks = <&gcc GCC_PCIE0_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "gcc_pcie0_pipe_clk_src";
				#clock-cells = <0>;
			};
		};

		mdio: mdio@90000 {
			#address-cells = <1>;
			#size-cells = <0>;
			compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio";
			reg = <0x0 0x00090000 0x0 0x64>;
			clocks = <&gcc GCC_MDIO_AHB_CLK>;
			clock-names = "gcc_mdio_ahb_clk";
			status = "disabled";
		};

		qfprom: efuse@a4000 {
			compatible = "qcom,ipq6018-qfprom", "qcom,qfprom";
			reg = <0x0 0x000a4000 0x0 0x2000>;
			#address-cells = <1>;
			#size-cells = <1>;
		};

		prng: qrng@e3000 {
			compatible = "qcom,prng-ee";
			reg = <0x0 0x000e3000 0x0 0x1000>;
			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "core";
		};

		cryptobam: dma-controller@704000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x0 0x00704000 0x0 0x20000>;
			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <1>;
			qcom,controlled-remotely;
		};

		crypto: crypto@73a000 {
			compatible = "qcom,crypto-v5.1";
			reg = <0x0 0x0073a000 0x0 0x6000>;
			clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
				 <&gcc GCC_CRYPTO_AXI_CLK>,
				 <&gcc GCC_CRYPTO_CLK>;
			clock-names = "iface", "bus", "core";
			dmas = <&cryptobam 2>, <&cryptobam 3>;
			dma-names = "rx", "tx";
		};

		tlmm: pinctrl@1000000 {
			compatible = "qcom,ipq6018-pinctrl";
			reg = <0x0 0x01000000 0x0 0x300000>;
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&tlmm 0 0 80>;
			interrupt-controller;
			#interrupt-cells = <2>;

			serial_3_pins: serial3-state {
				pins = "gpio44", "gpio45";
				function = "blsp2_uart";
				drive-strength = <8>;
				bias-pull-down;
			};

			qpic_pins: qpic-state {
				pins = "gpio1", "gpio3", "gpio4",
					"gpio5", "gpio6", "gpio7",
					"gpio8", "gpio10", "gpio11",
					"gpio12", "gpio13", "gpio14",
					"gpio15", "gpio17";
				function = "qpic_pad";
				drive-strength = <8>;
				bias-disable;
			};
		};

		gcc: gcc@1800000 {
			compatible = "qcom,gcc-ipq6018";
			reg = <0x0 0x01800000 0x0 0x80000>;
			clocks = <&xo>, <&sleep_clk>;
			clock-names = "xo", "sleep_clk";
			#clock-cells = <1>;
			#reset-cells = <1>;
		};

		tcsr_mutex: hwlock@1905000 {
			compatible = "qcom,ipq6018-tcsr-mutex", "qcom,tcsr-mutex";
			reg = <0x0 0x01905000 0x0 0x20000>;
			#hwlock-cells = <1>;
		};

		tcsr: syscon@1937000 {
			compatible = "qcom,tcsr-ipq6018", "syscon";
			reg = <0x0 0x01937000 0x0 0x21000>;
		};

		usb2: usb@70f8800 {
			compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
			reg = <0x0 0x070f8800 0x0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_USB1_MASTER_CLK>,
				 <&gcc GCC_USB1_SLEEP_CLK>,
				 <&gcc GCC_USB1_MOCK_UTMI_CLK>;
			clock-names = "core",
				      "sleep",
				      "mock_utmi";

			assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>,
					  <&gcc GCC_USB1_MOCK_UTMI_CLK>;
			assigned-clock-rates = <133330000>,
					       <24000000>;
			resets = <&gcc GCC_USB1_BCR>;
			status = "disabled";

			dwc_1: usb@7000000 {
				compatible = "snps,dwc3";
				reg = <0x0 0x07000000 0x0 0xcd00>;
				interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
				phys = <&qusb_phy_1>;
				phy-names = "usb2-phy";
				tx-fifo-resize;
				snps,is-utmi-l1-suspend;
				snps,hird-threshold = /bits/ 8 <0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_u3_susphy_quirk;
				dr_mode = "host";
			};
		};

		blsp_dma: dma-controller@7884000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x0 0x07884000 0x0 0x2b000>;
			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
		};

		blsp1_uart3: serial@78b1000 {
			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
			reg = <0x0 0x078b1000 0x0 0x200>;
			interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			status = "disabled";
		};

		blsp1_spi1: spi@78b5000 {
			compatible = "qcom,spi-qup-v2.2.1";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x078b5000 0x0 0x600>;
			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		blsp1_spi2: spi@78b6000 {
			compatible = "qcom,spi-qup-v2.2.1";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x078b6000 0x0 0x600>;
			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		blsp1_i2c2: i2c@78b6000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x078b6000 0x0 0x600>;
			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			clock-frequency = <400000>;
			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		blsp1_i2c3: i2c@78b7000 {
			compatible = "qcom,i2c-qup-v2.2.1";
			#address-cells = <1>;
			#size-cells = <0>;
			reg = <0x0 0x078b7000 0x0 0x600>;
			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
				 <&gcc GCC_BLSP1_AHB_CLK>;
			clock-names = "core", "iface";
			clock-frequency = <400000>;
			dmas = <&blsp_dma 16>, <&blsp_dma 17>;
			dma-names = "tx", "rx";
			status = "disabled";
		};

		qpic_bam: dma-controller@7984000 {
			compatible = "qcom,bam-v1.7.0";
			reg = <0x0 0x07984000 0x0 0x1a000>;
			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gcc GCC_QPIC_AHB_CLK>;
			clock-names = "bam_clk";
			#dma-cells = <1>;
			qcom,ee = <0>;
			status = "disabled";
		};

		qpic_nand: nand-controller@79b0000 {
			compatible = "qcom,ipq6018-nand";
			reg = <0x0 0x079b0000 0x0 0x10000>;
			#address-cells = <1>;
			#size-cells = <0>;
			clocks = <&gcc GCC_QPIC_CLK>,
				 <&gcc GCC_QPIC_AHB_CLK>;
			clock-names = "core", "aon";

			dmas = <&qpic_bam 0>,
			       <&qpic_bam 1>,
			       <&qpic_bam 2>;
			dma-names = "tx", "rx", "cmd";
			pinctrl-0 = <&qpic_pins>;
			pinctrl-names = "default";
			status = "disabled";
		};

		usb3: usb@8af8800 {
			compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
			reg = <0x0 0x08af8800 0x0 0x400>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
				<&gcc GCC_USB0_MASTER_CLK>,
				<&gcc GCC_USB0_SLEEP_CLK>,
				<&gcc GCC_USB0_MOCK_UTMI_CLK>;
			clock-names = "cfg_noc",
				"core",
				"sleep",
				"mock_utmi";

			assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
					  <&gcc GCC_USB0_MASTER_CLK>,
					  <&gcc GCC_USB0_MOCK_UTMI_CLK>;
			assigned-clock-rates = <133330000>,
					       <133330000>,
					       <24000000>;

			resets = <&gcc GCC_USB0_BCR>;
			status = "disabled";

			dwc_0: usb@8a00000 {
				compatible = "snps,dwc3";
				reg = <0x0 0x08a00000 0x0 0xcd00>;
				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
				phys = <&qusb_phy_0>, <&usb0_ssphy>;
				phy-names = "usb2-phy", "usb3-phy";
				clocks = <&xo>;
				clock-names = "ref";
				tx-fifo-resize;
				snps,parkmode-disable-ss-quirk;
				snps,is-utmi-l1-suspend;
				snps,hird-threshold = /bits/ 8 <0x0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_u3_susphy_quirk;
				dr_mode = "host";
			};
		};

		intc: interrupt-controller@b000000 {
			compatible = "qcom,msm-qgic2";
			#address-cells = <2>;
			#size-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x0 0x0b000000 0x0 0x1000>,  /*GICD*/
			      <0x0 0x0b002000 0x0 0x1000>,  /*GICC*/
			      <0x0 0x0b001000 0x0 0x1000>,  /*GICH*/
			      <0x0 0x0b004000 0x0 0x1000>;  /*GICV*/
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
			ranges = <0 0 0 0xb00a000 0 0xffd>;

			v2m@0 {
				compatible = "arm,gic-v2m-frame";
				msi-controller;
				reg = <0x0 0x0 0x0 0xffd>;
			};
		};

		watchdog@b017000 {
			compatible = "qcom,kpss-wdt";
			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
			reg = <0x0 0x0b017000 0x0 0x40>;
			clocks = <&sleep_clk>;
			timeout-sec = <10>;
		};

		apcs_glb: mailbox@b111000 {
			compatible = "qcom,ipq6018-apcs-apps-global";
			reg = <0x0 0x0b111000 0x0 0x1000>;
			#clock-cells = <1>;
			clocks = <&a53pll>, <&xo>;
			clock-names = "pll", "xo";
			#mbox-cells = <1>;
		};

		a53pll: clock@b116000 {
			compatible = "qcom,ipq6018-a53pll";
			reg = <0x0 0x0b116000 0x0 0x40>;
			#clock-cells = <0>;
			clocks = <&xo>;
			clock-names = "xo";
		};

		timer@b120000 {
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0 0 0x10000000>;
			compatible = "arm,armv7-timer-mem";
			reg = <0x0 0x0b120000 0x0 0x1000>;

			frame@b120000 {
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b121000 0x1000>,
				      <0x0b122000 0x1000>;
			};

			frame@b123000 {
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b123000 0x1000>;
				status = "disabled";
			};

			frame@b124000 {
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b124000 0x1000>;
				status = "disabled";
			};

			frame@b125000 {
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b125000 0x1000>;
				status = "disabled";
			};

			frame@b126000 {
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b126000 0x1000>;
				status = "disabled";
			};

			frame@b127000 {
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b127000 0x1000>;
				status = "disabled";
			};

			frame@b128000 {
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				reg = <0x0b128000 0x1000>;
				status = "disabled";
			};
		};

		q6v5_wcss: remoteproc@cd00000 {
			compatible = "qcom,ipq6018-wcss-pil";
			reg = <0x0 0x0cd00000 0x0 0x4040>,
			      <0x0 0x004ab000 0x0 0x20>;
			reg-names = "qdsp6",
				    "rmb";
			interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
					      <&wcss_smp2p_in 0 0>,
					      <&wcss_smp2p_in 1 0>,
					      <&wcss_smp2p_in 2 0>,
					      <&wcss_smp2p_in 3 0>;
			interrupt-names = "wdog",
					  "fatal",
					  "ready",
					  "handover",
					  "stop-ack";

			resets = <&gcc GCC_WCSSAON_RESET>,
				 <&gcc GCC_WCSS_BCR>,
				 <&gcc GCC_WCSS_Q6_BCR>;

			reset-names = "wcss_aon_reset",
				      "wcss_reset",
				      "wcss_q6_reset";

			clocks = <&gcc GCC_PRNG_AHB_CLK>;
			clock-names = "prng";

			qcom,halt-regs = <&tcsr 0x18000 0x1b000 0xe000>;

			qcom,smem-states = <&wcss_smp2p_out 0>,
					   <&wcss_smp2p_out 1>;
			qcom,smem-state-names = "shutdown",
						"stop";

			memory-region = <&q6_region>;

			glink-edge {
				interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>;
				label = "rtr";
				qcom,remote-pid = <1>;
				mboxes = <&apcs_glb 8>;

				qrtr_requests {
					qcom,glink-channels = "IPCRTR";
				};
			};
		};

		pcie0: pci@20000000 {
			compatible = "qcom,pcie-ipq6018";
			reg = <0x0 0x20000000 0x0 0xf1d>,
			      <0x0 0x20000f20 0x0 0xa8>,
			      <0x0 0x20001000 0x0 0x1000>,
			      <0x0 0x80000 0x0 0x4000>,
			      <0x0 0x20100000 0x0 0x1000>;
			reg-names = "dbi", "elbi", "atu", "parf", "config";

			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <1>;
			max-link-speed = <3>;
			#address-cells = <3>;
			#size-cells = <2>;

			phys = <&pcie_phy0>;
			phy-names = "pciephy";

			ranges = <0x81000000 0x0 0x00000000 0x0 0x20200000 0x0 0x10000>,
				 <0x82000000 0x0 0x20220000 0x0 0x20220000 0x0 0xfde0000>;

			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";

			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 0 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 0 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 0 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 0 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
				 <&gcc GCC_PCIE0_AXI_M_CLK>,
				 <&gcc GCC_PCIE0_AXI_S_CLK>,
				 <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
				 <&gcc PCIE0_RCHNG_CLK>;
			clock-names = "iface",
				      "axi_m",
				      "axi_s",
				      "axi_bridge",
				      "rchng";

			resets = <&gcc GCC_PCIE0_PIPE_ARES>,
				 <&gcc GCC_PCIE0_SLEEP_ARES>,
				 <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
				 <&gcc GCC_PCIE0_AXI_MASTER_ARES>,
				 <&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
				 <&gcc GCC_PCIE0_AHB_ARES>,
				 <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
				 <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
			reset-names = "pipe",
				      "sleep",
				      "sticky",
				      "axi_m",
				      "axi_s",
				      "ahb",
				      "axi_m_sticky",
				      "axi_s_sticky";

			status = "disabled";
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
	};

	wcss: wcss-smp2p {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;

		interrupt-parent = <&intc>;
		interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apcs_glb 9>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		wcss_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		wcss_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};
};