1/* 2 * dts file for Hisilicon HiKey Development Board 3 * 4 * Copyright (C) 2015, Hisilicon Ltd. 5 * 6 */ 7 8/dts-v1/; 9#include "hi6220.dtsi" 10#include "hikey-pinctrl.dtsi" 11#include <dt-bindings/gpio/gpio.h> 12 13/ { 14 model = "HiKey Development Board"; 15 compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220"; 16 17 aliases { 18 serial0 = &uart0; /* On board UART0 */ 19 serial1 = &uart1; /* BT UART */ 20 serial2 = &uart2; /* LS Expansion UART0 */ 21 serial3 = &uart3; /* LS Expansion UART1 */ 22 }; 23 24 chosen { 25 stdout-path = "serial3:115200n8"; 26 }; 27 28 /* 29 * Reserve below regions from memory node: 30 * 31 * 0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using 32 * 0x06df,f000 - 0x06df,ffff: Mailbox message data 33 * 0x0740,f000 - 0x0740,ffff: MCU firmware section 34 * 0x3e00,0000 - 0x3fff,ffff: OP-TEE 35 */ 36 memory@0 { 37 device_type = "memory"; 38 reg = <0x00000000 0x00000000 0x00000000 0x05e00000>, 39 <0x00000000 0x05f00000 0x00000000 0x00eff000>, 40 <0x00000000 0x06e00000 0x00000000 0x0060f000>, 41 <0x00000000 0x07410000 0x00000000 0x36bf0000>; 42 }; 43 44 soc { 45 spi0: spi@f7106000 { 46 status = "ok"; 47 }; 48 49 i2c0: i2c@f7100000 { 50 status = "ok"; 51 }; 52 53 i2c1: i2c@f7101000 { 54 status = "ok"; 55 }; 56 57 uart1: uart@f7111000 { 58 status = "ok"; 59 }; 60 61 uart2: uart@f7112000 { 62 status = "ok"; 63 }; 64 65 uart3: uart@f7113000 { 66 status = "ok"; 67 }; 68 69 /* 70 * Legend: proper name = the GPIO line is used as GPIO 71 * NC = not connected (not routed from the SoC) 72 * "[PER]" = pin is muxed for peripheral (not GPIO) 73 * "" = no idea, schematic doesn't say, could be 74 * unrouted (not connected to any external pin) 75 * LSEC = Low Speed External Connector 76 * HSEC = High Speed External Connector 77 * 78 * Pin assignments taken from LeMaker and CircuitCo Schematics 79 * Rev A1. 80 * 81 * For the lines routed to the external connectors the 82 * lines are named after the 96Boards CE Specification 1.0, 83 * Appendix "Expansion Connector Signal Description". 84 * 85 * When the 96Board naming of a line and the schematic name of 86 * the same line are in conflict, the 96Board specification 87 * takes precedence, which means that the external UART on the 88 * LSEC is named UART0 while the schematic and SoC names this 89 * UART2. This is only for the informational lines i.e. "[FOO]", 90 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only 91 * ones actually used for GPIO. 92 */ 93 gpio0: gpio@f8011000 { 94 gpio-line-names = "PWR_HOLD", "DSI_SEL", 95 "USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON", 96 "PWRON_DET", "5V_HUB_EN"; 97 }; 98 99 gpio1: gpio@f8012000 { 100 gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N", 101 "WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON"; 102 }; 103 104 gpio2: gpio@f8013000 { 105 gpio-line-names = 106 "GPIO-A", /* LSEC Pin 23: GPIO2_0 */ 107 "GPIO-B", /* LSEC Pin 24: GPIO2_1 */ 108 "GPIO-C", /* LSEC Pin 25: GPIO2_2 */ 109 "GPIO-D", /* LSEC Pin 26: GPIO2_3 */ 110 "GPIO-E", /* LSEC Pin 27: GPIO2_4 */ 111 "USB_ID_DET", "USB_VBUS_DET", 112 "GPIO-H"; /* LSEC Pin 30: GPIO2_7 */ 113 }; 114 115 gpio3: gpio@f8014000 { 116 gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "", 117 "WLAN_ACTIVE", "NC", "NC"; 118 }; 119 120 gpio4: gpio@f7020000 { 121 gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3", 122 "USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE"; 123 }; 124 125 gpio5: gpio@f7021000 { 126 gpio-line-names = "NC", "NC", 127 "[UART1_RxD]", /* LSEC Pin 11: UART3_RX */ 128 "[UART1_TxD]", /* LSEC Pin 13: UART3_TX */ 129 "[AUX_SSI1]", "NC", 130 "[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */ 131 "[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */ 132 }; 133 134 gpio6: gpio@f7022000 { 135 gpio-line-names = 136 "[SPI0_DIN]", /* Pin 10: SPI0_DI */ 137 "[SPI0_DOUT]", /* Pin 14: SPI0_DO */ 138 "[SPI0_CS]", /* Pin 12: SPI0_CS_N */ 139 "[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */ 140 "NC", "NC", "NC", 141 "GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */ 142 }; 143 144 gpio7: gpio@f7023000 { 145 gpio-line-names = "NC", "NC", "NC", "NC", 146 "[PCM_DI]", /* Pin 22: MODEM_PCM_DI */ 147 "[PCM_DO]", /* Pin 20: MODEM_PCM_DO */ 148 "NC", "NC"; 149 }; 150 151 gpio8: gpio@f7024000 { 152 gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC", 153 "", "", "", "", "", ""; 154 }; 155 156 gpio9: gpio@f7025000 { 157 gpio-line-names = "", 158 "GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */ 159 "GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */ 160 "NC", "NC", "NC", "NC", "[ISP_CCLK0]"; 161 }; 162 163 gpio10: gpio@f7026000 { 164 gpio-line-names = "BOOT_SEL", 165 "[ISP_CCLK1]", 166 "GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */ 167 "GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */ 168 "NC", "NC", 169 "[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */ 170 "[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */ 171 }; 172 173 gpio11: gpio@f7027000 { 174 gpio-line-names = 175 "[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */ 176 "[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */ 177 "", "NC", "NC", "NC", "", ""; 178 }; 179 180 gpio12: gpio@f7028000 { 181 gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]", 182 "[BT_PCM_DO]", 183 "NC", "NC", "NC", "NC", 184 "GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */ 185 }; 186 187 gpio13: gpio@f7029000 { 188 gpio-line-names = "[UART0_RX]", "[UART0_TX]", 189 "[BT_UART1_CTS]", "[BT_UART1_RTS]", 190 "[BT_UART1_RX]", "[BT_UART1_TX]", 191 "[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */ 192 "[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */ 193 }; 194 195 gpio14: gpio@f702a000 { 196 gpio-line-names = 197 "[UART0_RxD]", /* LSEC Pin 7: UART2_RX */ 198 "[UART0_TxD]", /* LSEC Pin 5: UART2_TX */ 199 "[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */ 200 "[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */ 201 "[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */ 202 "[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */ 203 "[I2C2_SCL]", "[I2C2_SDA]"; 204 }; 205 206 gpio15: gpio@f702b000 { 207 gpio-line-names = "", "", "", "", "", "", "NC", ""; 208 }; 209 210 /* GPIO blocks 16 thru 19 do not appear to be routed to pins */ 211 212 dwmmc_2: dwmmc2@f723f000 { 213 ti,non-removable; 214 non-removable; 215 /* WL_EN */ 216 vmmc-supply = <&wlan_en_reg>; 217 218 #address-cells = <0x1>; 219 #size-cells = <0x0>; 220 wlcore: wlcore@2 { 221 compatible = "ti,wl1835"; 222 reg = <2>; /* sdio func num */ 223 /* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */ 224 interrupt-parent = <&gpio1>; 225 interrupts = <3 IRQ_TYPE_EDGE_RISING>; 226 }; 227 }; 228 229 wlan_en_reg: regulator@1 { 230 compatible = "regulator-fixed"; 231 regulator-name = "wlan-en-regulator"; 232 regulator-min-microvolt = <1800000>; 233 regulator-max-microvolt = <1800000>; 234 /* WLAN_EN GPIO */ 235 gpio = <&gpio0 5 0>; 236 /* WLAN card specific delay */ 237 startup-delay-us = <70000>; 238 enable-active-high; 239 }; 240 }; 241 242 leds { 243 compatible = "gpio-leds"; 244 user_led4 { 245 label = "user_led4"; 246 gpios = <&gpio4 0 0>; /* <&gpio_user_led_1>; */ 247 linux,default-trigger = "heartbeat"; 248 }; 249 250 user_led3 { 251 label = "user_led3"; 252 gpios = <&gpio4 1 0>; /* <&gpio_user_led_2>; */ 253 linux,default-trigger = "mmc0"; 254 }; 255 256 user_led2 { 257 label = "user_led2"; 258 gpios = <&gpio4 2 0>; /* <&gpio_user_led_3>; */ 259 linux,default-trigger = "mmc1"; 260 }; 261 262 user_led1 { 263 label = "user_led1"; 264 gpios = <&gpio4 3 0>; /* <&gpio_user_led_4>; */ 265 linux,default-trigger = "cpu0"; 266 }; 267 268 wlan_active_led { 269 label = "wifi_active"; 270 gpios = <&gpio3 5 0>; /* <&gpio_wlan_active_led>; */ 271 linux,default-trigger = "phy0tx"; 272 default-state = "off"; 273 }; 274 275 bt_active_led { 276 label = "bt_active"; 277 gpios = <&gpio4 7 0>; /* <&gpio_bt_active_led>; */ 278 linux,default-trigger = "hci0rx"; 279 default-state = "off"; 280 }; 281 }; 282 283 pmic: pmic@f8000000 { 284 compatible = "hisilicon,hi655x-pmic"; 285 reg = <0x0 0xf8000000 0x0 0x1000>; 286 interrupt-controller; 287 #interrupt-cells = <2>; 288 pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; 289 290 regulators { 291 ldo2: LDO2 { 292 regulator-name = "LDO2_2V8"; 293 regulator-min-microvolt = <2500000>; 294 regulator-max-microvolt = <3200000>; 295 regulator-enable-ramp-delay = <120>; 296 }; 297 298 ldo7: LDO7 { 299 regulator-name = "LDO7_SDIO"; 300 regulator-min-microvolt = <1800000>; 301 regulator-max-microvolt = <3300000>; 302 regulator-enable-ramp-delay = <120>; 303 }; 304 305 ldo10: LDO10 { 306 regulator-name = "LDO10_2V85"; 307 regulator-min-microvolt = <1800000>; 308 regulator-max-microvolt = <3000000>; 309 regulator-enable-ramp-delay = <360>; 310 }; 311 312 ldo13: LDO13 { 313 regulator-name = "LDO13_1V8"; 314 regulator-min-microvolt = <1600000>; 315 regulator-max-microvolt = <1950000>; 316 regulator-enable-ramp-delay = <120>; 317 }; 318 319 ldo14: LDO14 { 320 regulator-name = "LDO14_2V8"; 321 regulator-min-microvolt = <2500000>; 322 regulator-max-microvolt = <3200000>; 323 regulator-enable-ramp-delay = <120>; 324 }; 325 326 ldo15: LDO15 { 327 regulator-name = "LDO15_1V8"; 328 regulator-min-microvolt = <1600000>; 329 regulator-max-microvolt = <1950000>; 330 regulator-boot-on; 331 regulator-always-on; 332 regulator-enable-ramp-delay = <120>; 333 }; 334 335 ldo17: LDO17 { 336 regulator-name = "LDO17_2V5"; 337 regulator-min-microvolt = <2500000>; 338 regulator-max-microvolt = <3200000>; 339 regulator-enable-ramp-delay = <120>; 340 }; 341 342 ldo19: LDO19 { 343 regulator-name = "LDO19_3V0"; 344 regulator-min-microvolt = <1800000>; 345 regulator-max-microvolt = <3000000>; 346 regulator-enable-ramp-delay = <360>; 347 }; 348 349 ldo21: LDO21 { 350 regulator-name = "LDO21_1V8"; 351 regulator-min-microvolt = <1650000>; 352 regulator-max-microvolt = <2000000>; 353 regulator-always-on; 354 regulator-enable-ramp-delay = <120>; 355 }; 356 357 ldo22: LDO22 { 358 regulator-name = "LDO22_1V2"; 359 regulator-min-microvolt = <900000>; 360 regulator-max-microvolt = <1200000>; 361 regulator-boot-on; 362 regulator-always-on; 363 regulator-enable-ramp-delay = <120>; 364 }; 365 }; 366 }; 367}; 368 369&uart2 { 370 label = "LS-UART0"; 371}; 372&uart3 { 373 label = "LS-UART1"; 374}; 375