1// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
2/*
3 * Copyright 2020-2021 TQ-Systems GmbH
4 */
5
6#include "imx8mm.dtsi"
7
8/ {
9	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
10	compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
11
12	memory@40000000 {
13		device_type = "memory";
14		/*  our minimum RAM config will be 1024 MiB */
15		reg = <0x00000000 0x40000000 0 0x40000000>;
16	};
17
18	/* e-MMC IO, needed for HS modes */
19	reg_vcc1v8: regulator-vcc1v8 {
20		compatible = "regulator-fixed";
21		regulator-name = "TQMA8MXML_VCC1V8";
22		regulator-min-microvolt = <1800000>;
23		regulator-max-microvolt = <1800000>;
24	};
25
26	/* identical to buck4_reg, but should never change */
27	reg_vcc3v3: regulator-vcc3v3 {
28		compatible = "regulator-fixed";
29		regulator-name = "TQMA8MXML_VCC3V3";
30		regulator-min-microvolt = <3300000>;
31		regulator-max-microvolt = <3300000>;
32	};
33
34	reserved-memory {
35		#address-cells = <2>;
36		#size-cells = <2>;
37		ranges;
38
39		/* global autoconfigured region for contiguous allocations */
40		linux,cma {
41			compatible = "shared-dma-pool";
42			reusable;
43			/* 640 MiB */
44			size = <0 0x28000000>;
45			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
46			alloc-ranges = <0 0x40000000 0 0x78000000>;
47			linux,cma-default;
48		};
49	};
50};
51
52&A53_0 {
53	cpu-supply = <&buck2_reg>;
54};
55
56&flexspi {
57	pinctrl-names = "default";
58	pinctrl-0 = <&pinctrl_flexspi>;
59	status = "okay";
60
61	flash0: flash@0 {
62		compatible = "jedec,spi-nor";
63		reg = <0>;
64		#address-cells = <1>;
65		#size-cells = <1>;
66		spi-max-frequency = <84000000>;
67		spi-tx-bus-width = <1>;
68		spi-rx-bus-width = <4>;
69	};
70};
71
72&gpu_2d {
73	status = "okay";
74};
75
76&gpu_3d {
77	status = "okay";
78};
79
80&i2c1 {
81	clock-frequency = <100000>;
82	pinctrl-names = "default", "gpio";
83	pinctrl-0 = <&pinctrl_i2c1>;
84	pinctrl-1 = <&pinctrl_i2c1_gpio>;
85	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
86	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
87	status = "okay";
88
89	sensor0: temperature-sensor-eeprom@1b {
90		compatible = "nxp,se97", "jedec,jc-42.4-temp";
91		reg = <0x1b>;
92	};
93
94	pca9450: pmic@25 {
95		compatible = "nxp,pca9450a";
96		reg = <0x25>;
97
98		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
99		pinctrl-0 = <&pinctrl_pmic>;
100		pinctrl-names = "default";
101		interrupt-parent = <&gpio1>;
102		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
103
104		regulators {
105			/* V_0V85_SOC: 0.85 */
106			buck1_reg: BUCK1 {
107				regulator-name = "BUCK1";
108				regulator-min-microvolt = <850000>;
109				regulator-max-microvolt = <850000>;
110				regulator-boot-on;
111				regulator-always-on;
112				regulator-ramp-delay = <3125>;
113			};
114
115			/* VDD_ARM */
116			buck2_reg: BUCK2 {
117				regulator-name = "BUCK2";
118				regulator-min-microvolt = <850000>;
119				regulator-max-microvolt = <1000000>;
120				regulator-boot-on;
121				regulator-always-on;
122				nxp,dvs-run-voltage = <950000>;
123				nxp,dvs-standby-voltage = <850000>;
124				regulator-ramp-delay = <3125>;
125			};
126
127			/* V_0V85_GPU / DRAM / VPU */
128			buck3_reg: BUCK3 {
129				regulator-name = "BUCK3";
130				regulator-min-microvolt = <850000>;
131				regulator-max-microvolt = <950000>;
132				regulator-boot-on;
133				regulator-always-on;
134				regulator-ramp-delay = <3125>;
135			};
136
137			/* VCC3V3 -> VMMC, ... must not be changed */
138			buck4_reg: BUCK4 {
139				regulator-name = "BUCK4";
140				regulator-min-microvolt = <3300000>;
141				regulator-max-microvolt = <3300000>;
142				regulator-boot-on;
143				regulator-always-on;
144			};
145
146			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
147			buck5_reg: BUCK5 {
148				regulator-name = "BUCK5";
149				regulator-min-microvolt = <1800000>;
150				regulator-max-microvolt = <1800000>;
151				regulator-boot-on;
152				regulator-always-on;
153			};
154
155			/* V_1V1 -> RAM, ... must not be changed */
156			buck6_reg: BUCK6 {
157				regulator-name = "BUCK6";
158				regulator-min-microvolt = <1100000>;
159				regulator-max-microvolt = <1100000>;
160				regulator-boot-on;
161				regulator-always-on;
162			};
163
164			/* V_1V8_SNVS */
165			ldo1_reg: LDO1 {
166				regulator-name = "LDO1";
167				regulator-min-microvolt = <1800000>;
168				regulator-max-microvolt = <1800000>;
169				regulator-boot-on;
170				regulator-always-on;
171			};
172
173			/* V_0V8_SNVS */
174			ldo2_reg: LDO2 {
175				regulator-name = "LDO2";
176				regulator-min-microvolt = <800000>;
177				regulator-max-microvolt = <850000>;
178				regulator-boot-on;
179				regulator-always-on;
180			};
181
182			/* V_1V8_ANA */
183			ldo3_reg: LDO3 {
184				regulator-name = "LDO3";
185				regulator-min-microvolt = <1800000>;
186				regulator-max-microvolt = <1800000>;
187				regulator-boot-on;
188				regulator-always-on;
189			};
190
191			/* V_0V9_MIPI */
192			ldo4_reg: LDO4 {
193				regulator-name = "LDO4";
194				regulator-min-microvolt = <900000>;
195				regulator-max-microvolt = <900000>;
196				regulator-boot-on;
197				regulator-always-on;
198			};
199
200			/* VCC SD IO - switched using SD2 VSELECT */
201			ldo5_reg: LDO5 {
202				regulator-name = "LDO5";
203				regulator-min-microvolt = <1800000>;
204				regulator-max-microvolt = <3300000>;
205			};
206		};
207	};
208
209
210	pcf85063: rtc@51 {
211		compatible = "nxp,pcf85063a";
212		reg = <0x51>;
213		quartz-load-femtofarads = <7000>;
214	};
215
216	eeprom1: eeprom@53 {
217		compatible = "nxp,se97b", "atmel,24c02";
218		read-only;
219		reg = <0x53>;
220		pagesize = <16>;
221	};
222
223	eeprom0: eeprom@57 {
224		compatible = "atmel,24c64";
225		reg = <0x57>;
226		pagesize = <32>;
227	};
228};
229
230&pcie_phy {
231	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
232	fsl,clkreq-unsupported;
233};
234
235&usdhc3 {
236	pinctrl-names = "default", "state_100mhz", "state_200mhz";
237	pinctrl-0 = <&pinctrl_usdhc3>;
238	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
239	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
240	bus-width = <8>;
241	non-removable;
242	no-sd;
243	no-sdio;
244	vmmc-supply = <&reg_vcc3v3>;
245	vqmmc-supply = <&reg_vcc1v8>;
246	status = "okay";
247};
248
249/*
250 * Attention:
251 * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
252 * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
253 */
254&wdog1 {
255	pinctrl-names = "default";
256	pinctrl-0 = <&pinctrl_wdog>;
257	fsl,ext-reset-output;
258	status = "okay";
259};
260
261&iomuxc {
262	pinctrl_flexspi: flexspigrp {
263		fsl,pins = <MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x82>,
264			   <MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82>,
265			   <MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82>,
266			   <MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82>,
267			   <MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82>,
268			   <MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82>;
269	};
270
271	pinctrl_i2c1: i2c1grp {
272		fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x40000004>,
273			   <MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x40000004>;
274	};
275
276	pinctrl_i2c1_gpio: i2c1gpiogrp {
277		fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x40000004>,
278			   <MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x40000004>;
279	};
280
281	pinctrl_pmic: pmicgrp {
282		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x94>;
283	};
284
285	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
286		fsl,pins = <MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x84>;
287	};
288
289	pinctrl_usdhc3: usdhc3grp {
290		fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d4>,
291			   <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
292			   <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
293			   <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
294			   <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
295			   <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
296			   <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
297			   <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
298			   <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
299			   <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
300			   <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
301			   /* option USDHC3_RESET_B not defined, only in RM */
302			   <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x84>;
303	};
304
305	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
306		fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d2>,
307			   <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
308			   <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
309			   <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
310			   <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
311			   <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
312			   <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
313			   <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
314			   <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
315			   <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
316			   <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
317			   /* option USDHC3_RESET_B not defined, only in RM */
318			   <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x84>;
319	};
320
321	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
322		fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d6>,
323			   <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
324			   <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
325			   <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
326			   <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
327			   <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
328			   <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
329			   <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
330			   <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
331			   <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
332			   <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
333			   /* option USDHC3_RESET_B not defined, only in RM */
334			   <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x84>;
335	};
336
337	pinctrl_wdog: wdoggrp {
338		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x84>;
339	};
340};
341