1config MAC80211 2 tristate "Generic IEEE 802.11 Networking Stack (mac80211)" 3 select CRYPTO 4 select CRYPTO_ECB 5 select CRYPTO_ARC4 6 select CRYPTO_AES 7 select CRC32 8 select WIRELESS_EXT 9 select CFG80211 10 select NET_SCH_FIFO 11 ---help--- 12 This option enables the hardware independent IEEE 802.11 13 networking stack. 14 15menu "Rate control algorithm selection" 16 depends on MAC80211 != n 17 18choice 19 prompt "Default rate control algorithm" 20 default MAC80211_RC_DEFAULT_PID 21 ---help--- 22 This option selects the default rate control algorithm 23 mac80211 will use. Note that this default can still be 24 overriden through the ieee80211_default_rc_algo module 25 parameter if different algorithms are available. 26 27config MAC80211_RC_DEFAULT_PID 28 bool "PID controller based rate control algorithm" 29 select MAC80211_RC_PID 30 ---help--- 31 Select the PID controller based rate control as the 32 default rate control algorithm. You should choose 33 this unless you know what you are doing. 34 35config MAC80211_RC_DEFAULT_NONE 36 bool "No default algorithm" 37 depends on EMBEDDED 38 help 39 Selecting this option will select no default algorithm 40 and allow you to not build any. Do not choose this 41 option unless you know your driver comes with another 42 suitable algorithm. 43endchoice 44 45comment "Selecting 'y' for an algorithm will" 46comment "build the algorithm into mac80211." 47 48config MAC80211_RC_DEFAULT 49 string 50 default "pid" if MAC80211_RC_DEFAULT_PID 51 default "" 52 53config MAC80211_RC_PID 54 tristate "PID controller based rate control algorithm" 55 ---help--- 56 This option enables a TX rate control algorithm for 57 mac80211 that uses a PID controller to select the TX 58 rate. 59 60 Say Y or M unless you're sure you want to use a 61 different rate control algorithm. 62 63endmenu 64 65config MAC80211_MESH 66 bool "Enable mac80211 mesh networking (pre-802.11s) support" 67 depends on MAC80211 && EXPERIMENTAL 68 ---help--- 69 This options enables support of Draft 802.11s mesh networking. 70 The implementation is based on Draft 1.08 of the Mesh Networking 71 amendment. For more information visit http://o11s.org/. 72 73 74config MAC80211_LEDS 75 bool "Enable LED triggers" 76 depends on MAC80211 && LEDS_TRIGGERS 77 ---help--- 78 This option enables a few LED triggers for different 79 packet receive/transmit events. 80 81config MAC80211_DEBUGFS 82 bool "Export mac80211 internals in DebugFS" 83 depends on MAC80211 && DEBUG_FS 84 ---help--- 85 Select this to see extensive information about 86 the internal state of mac80211 in debugfs. 87 88 Say N unless you know you need this. 89 90config MAC80211_DEBUG_PACKET_ALIGNMENT 91 bool "Enable packet alignment debugging" 92 depends on MAC80211 93 help 94 This option is recommended for driver authors and strongly 95 discouraged for everybody else, it will trigger a warning 96 when a driver hands mac80211 a buffer that is aligned in 97 a way that will cause problems with the IP stack on some 98 architectures. 99 100 Say N unless you're writing a mac80211 based driver. 101 102config MAC80211_DEBUG 103 bool "Enable debugging output" 104 depends on MAC80211 105 ---help--- 106 This option will enable debug tracing output for the 107 ieee80211 network stack. 108 109 If you are not trying to debug or develop the ieee80211 110 subsystem, you most likely want to say N here. 111 112config MAC80211_HT_DEBUG 113 bool "Enable HT debugging output" 114 depends on MAC80211_DEBUG 115 ---help--- 116 This option enables 802.11n High Throughput features 117 debug tracing output. 118 119 If you are not trying to debug of develop the ieee80211 120 subsystem, you most likely want to say N here. 121 122config MAC80211_VERBOSE_DEBUG 123 bool "Verbose debugging output" 124 depends on MAC80211_DEBUG 125 126config MAC80211_LOWTX_FRAME_DUMP 127 bool "Debug frame dumping" 128 depends on MAC80211_DEBUG 129 ---help--- 130 Selecting this option will cause the stack to 131 print a message for each frame that is handed 132 to the lowlevel driver for transmission. This 133 message includes all MAC addresses and the 134 frame control field. 135 136 If unsure, say N and insert the debugging code 137 you require into the driver you are debugging. 138 139config TKIP_DEBUG 140 bool "TKIP debugging" 141 depends on MAC80211_DEBUG 142 143config MAC80211_DEBUG_COUNTERS 144 bool "Extra statistics for TX/RX debugging" 145 depends on MAC80211_DEBUG 146 147config MAC80211_IBSS_DEBUG 148 bool "Support for IBSS testing" 149 depends on MAC80211_DEBUG 150 ---help--- 151 Say Y here if you intend to debug the IBSS code. 152 153config MAC80211_VERBOSE_PS_DEBUG 154 bool "Verbose powersave mode debugging" 155 depends on MAC80211_DEBUG 156 ---help--- 157 Say Y here to print out verbose powersave 158 mode debug messages. 159 160config MAC80211_VERBOSE_MPL_DEBUG 161 bool "Verbose mesh peer link debugging" 162 depends on MAC80211_DEBUG && MAC80211_MESH 163 ---help--- 164 Say Y here to print out verbose mesh peer link 165 debug messages. 166