1config MAC80211 2 tristate "Generic IEEE 802.11 Networking Stack (mac80211)" 3 select CRYPTO 4 select CRYPTO_ECB 5 select CRYPTO_ARC4 6 select CRYPTO_AES 7 select CRC32 8 select WIRELESS_EXT 9 select CFG80211 10 select NET_SCH_FIFO 11 ---help--- 12 This option enables the hardware independent IEEE 802.11 13 networking stack. 14 15menu "Rate control algorithm selection" 16 depends on MAC80211 != n 17 18choice 19 prompt "Default rate control algorithm" 20 default MAC80211_RC_DEFAULT_PID 21 ---help--- 22 This option selects the default rate control algorithm 23 mac80211 will use. Note that this default can still be 24 overriden through the ieee80211_default_rc_algo module 25 parameter if different algorithms are available. 26 27config MAC80211_RC_DEFAULT_PID 28 bool "PID controller based rate control algorithm" 29 select MAC80211_RC_PID 30 ---help--- 31 Select the PID controller based rate control as the 32 default rate control algorithm. You should choose 33 this unless you know what you are doing. 34 35config MAC80211_RC_DEFAULT_NONE 36 bool "No default algorithm" 37 depends on EMBEDDED 38 help 39 Selecting this option will select no default algorithm 40 and allow you to not build any. Do not choose this 41 option unless you know your driver comes with another 42 suitable algorithm. 43endchoice 44 45comment "Selecting 'y' for an algorithm will" 46comment "build the algorithm into mac80211." 47 48config MAC80211_RC_DEFAULT 49 string 50 default "pid" if MAC80211_RC_DEFAULT_PID 51 default "" 52 53config MAC80211_RC_PID 54 tristate "PID controller based rate control algorithm" 55 ---help--- 56 This option enables a TX rate control algorithm for 57 mac80211 that uses a PID controller to select the TX 58 rate. 59 60 Say Y or M unless you're sure you want to use a 61 different rate control algorithm. 62 63endmenu 64 65config MAC80211_MESH 66 bool "Enable mac80211 mesh networking (pre-802.11s) support" 67 depends on MAC80211 && EXPERIMENTAL 68 ---help--- 69 This options enables support of Draft 802.11s mesh networking. 70 The implementation is based on Draft 1.08 of the Mesh Networking 71 amendment. For more information visit http://o11s.org/. 72 73 74config MAC80211_LEDS 75 bool "Enable LED triggers" 76 depends on MAC80211 77 select NEW_LEDS 78 select LEDS_TRIGGERS 79 ---help--- 80 This option enables a few LED triggers for different 81 packet receive/transmit events. 82 83config MAC80211_DEBUGFS 84 bool "Export mac80211 internals in DebugFS" 85 depends on MAC80211 && DEBUG_FS 86 ---help--- 87 Select this to see extensive information about 88 the internal state of mac80211 in debugfs. 89 90 Say N unless you know you need this. 91 92config MAC80211_DEBUG_PACKET_ALIGNMENT 93 bool "Enable packet alignment debugging" 94 depends on MAC80211 95 help 96 This option is recommended for driver authors and strongly 97 discouraged for everybody else, it will trigger a warning 98 when a driver hands mac80211 a buffer that is aligned in 99 a way that will cause problems with the IP stack on some 100 architectures. 101 102 Say N unless you're writing a mac80211 based driver. 103 104config MAC80211_DEBUG 105 bool "Enable debugging output" 106 depends on MAC80211 107 ---help--- 108 This option will enable debug tracing output for the 109 ieee80211 network stack. 110 111 If you are not trying to debug or develop the ieee80211 112 subsystem, you most likely want to say N here. 113 114config MAC80211_HT_DEBUG 115 bool "Enable HT debugging output" 116 depends on MAC80211_DEBUG 117 ---help--- 118 This option enables 802.11n High Throughput features 119 debug tracing output. 120 121 If you are not trying to debug of develop the ieee80211 122 subsystem, you most likely want to say N here. 123 124config MAC80211_VERBOSE_DEBUG 125 bool "Verbose debugging output" 126 depends on MAC80211_DEBUG 127 128config MAC80211_LOWTX_FRAME_DUMP 129 bool "Debug frame dumping" 130 depends on MAC80211_DEBUG 131 ---help--- 132 Selecting this option will cause the stack to 133 print a message for each frame that is handed 134 to the lowlevel driver for transmission. This 135 message includes all MAC addresses and the 136 frame control field. 137 138 If unsure, say N and insert the debugging code 139 you require into the driver you are debugging. 140 141config TKIP_DEBUG 142 bool "TKIP debugging" 143 depends on MAC80211_DEBUG 144 145config MAC80211_DEBUG_COUNTERS 146 bool "Extra statistics for TX/RX debugging" 147 depends on MAC80211_DEBUG 148 149config MAC80211_IBSS_DEBUG 150 bool "Support for IBSS testing" 151 depends on MAC80211_DEBUG 152 ---help--- 153 Say Y here if you intend to debug the IBSS code. 154 155config MAC80211_VERBOSE_PS_DEBUG 156 bool "Verbose powersave mode debugging" 157 depends on MAC80211_DEBUG 158 ---help--- 159 Say Y here to print out verbose powersave 160 mode debug messages. 161 162config MAC80211_VERBOSE_MPL_DEBUG 163 bool "Verbose mesh peer link debugging" 164 depends on MAC80211_DEBUG && MAC80211_MESH 165 ---help--- 166 Say Y here to print out verbose mesh peer link 167 debug messages. 168