1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved. 4 */ 5 6 #ifndef _UFS_QUIRKS_H_ 7 #define _UFS_QUIRKS_H_ 8 9 /* return true if s1 is a prefix of s2 */ 10 #define STR_PRFX_EQUAL(s1, s2) !strncmp(s1, s2, strlen(s1)) 11 12 #define UFS_ANY_VENDOR 0xFFFF 13 #define UFS_ANY_MODEL "ANY_MODEL" 14 15 #define UFS_VENDOR_MICRON 0x12C 16 #define UFS_VENDOR_SAMSUNG 0x1CE 17 #define UFS_VENDOR_SKHYNIX 0x1AD 18 #define UFS_VENDOR_TOSHIBA 0x198 19 #define UFS_VENDOR_WDC 0x145 20 21 /** 22 * ufs_dev_quirk - ufs device quirk info 23 * @card: ufs card details 24 * @quirk: device quirk 25 */ 26 struct ufs_dev_quirk { 27 u16 wmanufacturerid; 28 const u8 *model; 29 unsigned int quirk; 30 }; 31 32 /* 33 * Some vendor's UFS device sends back to back NACs for the DL data frames 34 * causing the host controller to raise the DFES error status. Sometimes 35 * such UFS devices send back to back NAC without waiting for new 36 * retransmitted DL frame from the host and in such cases it might be possible 37 * the Host UniPro goes into bad state without raising the DFES error 38 * interrupt. If this happens then all the pending commands would timeout 39 * only after respective SW command (which is generally too large). 40 * 41 * We can workaround such device behaviour like this: 42 * - As soon as SW sees the DL NAC error, it should schedule the error handler 43 * - Error handler would sleep for 50ms to see if there are any fatal errors 44 * raised by UFS controller. 45 * - If there are fatal errors then SW does normal error recovery. 46 * - If there are no fatal errors then SW sends the NOP command to device 47 * to check if link is alive. 48 * - If NOP command times out, SW does normal error recovery 49 * - If NOP command succeed, skip the error handling. 50 * 51 * If DL NAC error is seen multiple times with some vendor's UFS devices then 52 * enable this quirk to initiate quick error recovery and also silence related 53 * error logs to reduce spamming of kernel logs. 54 */ 55 #define UFS_DEVICE_QUIRK_RECOVERY_FROM_DL_NAC_ERRORS (1 << 2) 56 57 /* 58 * Few Toshiba UFS device models advertise RX_MIN_ACTIVATETIME_CAPABILITY as 59 * 600us which may not be enough for reliable hibern8 exit hardware sequence 60 * from UFS device. 61 * To workaround this issue, host should set its PA_TACTIVATE time to 1ms even 62 * if device advertises RX_MIN_ACTIVATETIME_CAPABILITY less than 1ms. 63 */ 64 #define UFS_DEVICE_QUIRK_PA_TACTIVATE (1 << 4) 65 66 /* 67 * It seems some UFS devices may keep drawing more than sleep current 68 * (atleast for 500us) from UFS rails (especially from VCCQ rail). 69 * To avoid this situation, add 2ms delay before putting these UFS 70 * rails in LPM mode. 71 */ 72 #define UFS_DEVICE_QUIRK_DELAY_BEFORE_LPM (1 << 6) 73 74 /* 75 * Some UFS devices require host PA_TACTIVATE to be lower than device 76 * PA_TACTIVATE, enabling this quirk ensure this. 77 */ 78 #define UFS_DEVICE_QUIRK_HOST_PA_TACTIVATE (1 << 7) 79 80 /* 81 * The max. value PA_SaveConfigTime is 250 (10us) but this is not enough for 82 * some vendors. 83 * Gear switch from PWM to HS may fail even with this max. PA_SaveConfigTime. 84 * Gear switch can be issued by host controller as an error recovery and any 85 * software delay will not help on this case so we need to increase 86 * PA_SaveConfigTime to >32us as per vendor recommendation. 87 */ 88 #define UFS_DEVICE_QUIRK_HOST_PA_SAVECONFIGTIME (1 << 8) 89 90 /* 91 * Some UFS devices require VS_DebugSaveConfigTime is 0x10, 92 * enabling this quirk ensure this. 93 */ 94 #define UFS_DEVICE_QUIRK_HOST_VS_DEBUGSAVECONFIGTIME (1 << 9) 95 96 /* 97 * Some pre-3.1 UFS devices can support extended features by upgrading 98 * the firmware. Enable this quirk to make UFS core driver probe and enable 99 * supported features on such devices. 100 */ 101 #define UFS_DEVICE_QUIRK_SUPPORT_EXTENDED_FEATURES (1 << 10) 102 103 /* 104 * Some UFS devices require delay after VCC power rail is turned-off. 105 * Enable this quirk to introduce 5ms delays after VCC power-off during 106 * suspend flow. 107 */ 108 #define UFS_DEVICE_QUIRK_DELAY_AFTER_LPM (1 << 11) 109 110 /* 111 * Some UFS devices require L2P entry should be swapped before being sent to the 112 * UFS device for HPB READ command. 113 */ 114 #define UFS_DEVICE_QUIRK_SWAP_L2P_ENTRY_FOR_HPB_READ (1 << 12) 115 116 #endif /* UFS_QUIRKS_H_ */ 117