1 /* 2 * Copyright(c) 2007 Intel Corporation. All rights reserved. 3 * 4 * This program is free software; you can redistribute it and/or modify it 5 * under the terms and conditions of the GNU General Public License, 6 * version 2, as published by the Free Software Foundation. 7 * 8 * This program is distributed in the hope it will be useful, but WITHOUT 9 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 10 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 11 * more details. 12 * 13 * You should have received a copy of the GNU General Public License along with 14 * this program; if not, write to the Free Software Foundation, Inc., 15 * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. 16 * 17 * Maintained at www.Open-FCoE.org 18 */ 19 20 #ifndef _FC_FS_H_ 21 #define _FC_FS_H_ 22 23 #include <linux/types.h> 24 25 /* 26 * Fibre Channel Framing and Signalling definitions. 27 * From T11 FC-FS-2 Rev 0.90 - 9 August 2005. 28 */ 29 30 /* 31 * Frame header 32 */ 33 struct fc_frame_header { 34 __u8 fh_r_ctl; /* routing control */ 35 __u8 fh_d_id[3]; /* Destination ID */ 36 37 __u8 fh_cs_ctl; /* class of service control / pri */ 38 __u8 fh_s_id[3]; /* Source ID */ 39 40 __u8 fh_type; /* see enum fc_fh_type below */ 41 __u8 fh_f_ctl[3]; /* frame control */ 42 43 __u8 fh_seq_id; /* sequence ID */ 44 __u8 fh_df_ctl; /* data field control */ 45 __be16 fh_seq_cnt; /* sequence count */ 46 47 __be16 fh_ox_id; /* originator exchange ID */ 48 __be16 fh_rx_id; /* responder exchange ID */ 49 __be32 fh_parm_offset; /* parameter or relative offset */ 50 }; 51 52 #define FC_FRAME_HEADER_LEN 24 /* expected length of structure */ 53 54 #define FC_MAX_PAYLOAD 2112U /* max payload length in bytes */ 55 #define FC_MIN_MAX_PAYLOAD 256U /* lower limit on max payload */ 56 57 #define FC_MAX_FRAME (FC_MAX_PAYLOAD + FC_FRAME_HEADER_LEN) 58 #define FC_MIN_MAX_FRAME (FC_MIN_MAX_PAYLOAD + FC_FRAME_HEADER_LEN) 59 60 /* 61 * fh_r_ctl - Routing control definitions. 62 */ 63 /* 64 * FC-4 device_data. 65 */ 66 enum fc_rctl { 67 FC_RCTL_DD_UNCAT = 0x00, /* uncategorized information */ 68 FC_RCTL_DD_SOL_DATA = 0x01, /* solicited data */ 69 FC_RCTL_DD_UNSOL_CTL = 0x02, /* unsolicited control */ 70 FC_RCTL_DD_SOL_CTL = 0x03, /* solicited control or reply */ 71 FC_RCTL_DD_UNSOL_DATA = 0x04, /* unsolicited data */ 72 FC_RCTL_DD_DATA_DESC = 0x05, /* data descriptor */ 73 FC_RCTL_DD_UNSOL_CMD = 0x06, /* unsolicited command */ 74 FC_RCTL_DD_CMD_STATUS = 0x07, /* command status */ 75 76 #define FC_RCTL_ILS_REQ FC_RCTL_DD_UNSOL_CTL /* ILS request */ 77 #define FC_RCTL_ILS_REP FC_RCTL_DD_SOL_CTL /* ILS reply */ 78 79 /* 80 * Extended Link_Data 81 */ 82 FC_RCTL_ELS_REQ = 0x22, /* extended link services request */ 83 FC_RCTL_ELS_REP = 0x23, /* extended link services reply */ 84 FC_RCTL_ELS4_REQ = 0x32, /* FC-4 ELS request */ 85 FC_RCTL_ELS4_REP = 0x33, /* FC-4 ELS reply */ 86 /* 87 * Optional Extended Headers 88 */ 89 FC_RCTL_VFTH = 0x50, /* virtual fabric tagging header */ 90 FC_RCTL_IFRH = 0x51, /* inter-fabric routing header */ 91 FC_RCTL_ENCH = 0x52, /* encapsulation header */ 92 /* 93 * Basic Link Services fh_r_ctl values. 94 */ 95 FC_RCTL_BA_NOP = 0x80, /* basic link service NOP */ 96 FC_RCTL_BA_ABTS = 0x81, /* basic link service abort */ 97 FC_RCTL_BA_RMC = 0x82, /* remove connection */ 98 FC_RCTL_BA_ACC = 0x84, /* basic accept */ 99 FC_RCTL_BA_RJT = 0x85, /* basic reject */ 100 FC_RCTL_BA_PRMT = 0x86, /* dedicated connection preempted */ 101 /* 102 * Link Control Information. 103 */ 104 FC_RCTL_ACK_1 = 0xc0, /* acknowledge_1 */ 105 FC_RCTL_ACK_0 = 0xc1, /* acknowledge_0 */ 106 FC_RCTL_P_RJT = 0xc2, /* port reject */ 107 FC_RCTL_F_RJT = 0xc3, /* fabric reject */ 108 FC_RCTL_P_BSY = 0xc4, /* port busy */ 109 FC_RCTL_F_BSY = 0xc5, /* fabric busy to data frame */ 110 FC_RCTL_F_BSYL = 0xc6, /* fabric busy to link control frame */ 111 FC_RCTL_LCR = 0xc7, /* link credit reset */ 112 FC_RCTL_END = 0xc9, /* end */ 113 }; 114 /* incomplete list of definitions */ 115 116 /* 117 * R_CTL names initializer. 118 * Please keep this matching the above definitions. 119 */ 120 #define FC_RCTL_NAMES_INIT { \ 121 [FC_RCTL_DD_UNCAT] = "uncat", \ 122 [FC_RCTL_DD_SOL_DATA] = "sol data", \ 123 [FC_RCTL_DD_UNSOL_CTL] = "unsol ctl", \ 124 [FC_RCTL_DD_SOL_CTL] = "sol ctl/reply", \ 125 [FC_RCTL_DD_UNSOL_DATA] = "unsol data", \ 126 [FC_RCTL_DD_DATA_DESC] = "data desc", \ 127 [FC_RCTL_DD_UNSOL_CMD] = "unsol cmd", \ 128 [FC_RCTL_DD_CMD_STATUS] = "cmd status", \ 129 [FC_RCTL_ELS_REQ] = "ELS req", \ 130 [FC_RCTL_ELS_REP] = "ELS rep", \ 131 [FC_RCTL_ELS4_REQ] = "FC-4 ELS req", \ 132 [FC_RCTL_ELS4_REP] = "FC-4 ELS rep", \ 133 [FC_RCTL_BA_NOP] = "BLS NOP", \ 134 [FC_RCTL_BA_ABTS] = "BLS abort", \ 135 [FC_RCTL_BA_RMC] = "BLS remove connection", \ 136 [FC_RCTL_BA_ACC] = "BLS accept", \ 137 [FC_RCTL_BA_RJT] = "BLS reject", \ 138 [FC_RCTL_BA_PRMT] = "BLS dedicated connection preempted", \ 139 [FC_RCTL_ACK_1] = "LC ACK_1", \ 140 [FC_RCTL_ACK_0] = "LC ACK_0", \ 141 [FC_RCTL_P_RJT] = "LC port reject", \ 142 [FC_RCTL_F_RJT] = "LC fabric reject", \ 143 [FC_RCTL_P_BSY] = "LC port busy", \ 144 [FC_RCTL_F_BSY] = "LC fabric busy to data frame", \ 145 [FC_RCTL_F_BSYL] = "LC fabric busy to link control frame",\ 146 [FC_RCTL_LCR] = "LC link credit reset", \ 147 [FC_RCTL_END] = "LC end", \ 148 } 149 150 /* 151 * Well-known fabric addresses. 152 */ 153 enum fc_well_known_fid { 154 FC_FID_NONE = 0x000000, /* No destination */ 155 FC_FID_BCAST = 0xffffff, /* broadcast */ 156 FC_FID_FLOGI = 0xfffffe, /* fabric login */ 157 FC_FID_FCTRL = 0xfffffd, /* fabric controller */ 158 FC_FID_DIR_SERV = 0xfffffc, /* directory server */ 159 FC_FID_TIME_SERV = 0xfffffb, /* time server */ 160 FC_FID_MGMT_SERV = 0xfffffa, /* management server */ 161 FC_FID_QOS = 0xfffff9, /* QoS Facilitator */ 162 FC_FID_ALIASES = 0xfffff8, /* alias server (FC-PH2) */ 163 FC_FID_SEC_KEY = 0xfffff7, /* Security key dist. server */ 164 FC_FID_CLOCK = 0xfffff6, /* clock synch server */ 165 FC_FID_MCAST_SERV = 0xfffff5, /* multicast server */ 166 }; 167 168 #define FC_FID_WELL_KNOWN_MAX 0xffffff /* highest well-known fabric ID */ 169 #define FC_FID_WELL_KNOWN_BASE 0xfffff5 /* start of well-known fabric ID */ 170 171 /* 172 * Other well-known addresses, outside the above contiguous range. 173 */ 174 #define FC_FID_DOM_MGR 0xfffc00 /* domain manager base */ 175 176 /* 177 * Fabric ID bytes. 178 */ 179 #define FC_FID_DOMAIN 0 180 #define FC_FID_PORT 1 181 #define FC_FID_LINK 2 182 183 /* 184 * fh_type codes 185 */ 186 enum fc_fh_type { 187 FC_TYPE_BLS = 0x00, /* basic link service */ 188 FC_TYPE_ELS = 0x01, /* extended link service */ 189 FC_TYPE_IP = 0x05, /* IP over FC, RFC 4338 */ 190 FC_TYPE_FCP = 0x08, /* SCSI FCP */ 191 FC_TYPE_CT = 0x20, /* Fibre Channel Services (FC-CT) */ 192 FC_TYPE_ILS = 0x22, /* internal link service */ 193 FC_TYPE_NVME = 0x28, /* FC-NVME */ 194 }; 195 196 /* 197 * FC_TYPE names initializer. 198 * Please keep this matching the above definitions. 199 */ 200 #define FC_TYPE_NAMES_INIT { \ 201 [FC_TYPE_BLS] = "BLS", \ 202 [FC_TYPE_ELS] = "ELS", \ 203 [FC_TYPE_IP] = "IP", \ 204 [FC_TYPE_FCP] = "FCP", \ 205 [FC_TYPE_CT] = "CT", \ 206 [FC_TYPE_ILS] = "ILS", \ 207 [FC_TYPE_NVME] = "NVME", \ 208 } 209 210 /* 211 * Exchange IDs. 212 */ 213 #define FC_XID_UNKNOWN 0xffff /* unknown exchange ID */ 214 #define FC_XID_MIN 0x0 /* supported min exchange ID */ 215 #define FC_XID_MAX 0xfffe /* supported max exchange ID */ 216 217 /* 218 * fh_f_ctl - Frame control flags. 219 */ 220 #define FC_FC_EX_CTX (1 << 23) /* sent by responder to exchange */ 221 #define FC_FC_SEQ_CTX (1 << 22) /* sent by responder to sequence */ 222 #define FC_FC_FIRST_SEQ (1 << 21) /* first sequence of this exchange */ 223 #define FC_FC_LAST_SEQ (1 << 20) /* last sequence of this exchange */ 224 #define FC_FC_END_SEQ (1 << 19) /* last frame of sequence */ 225 #define FC_FC_END_CONN (1 << 18) /* end of class 1 connection pending */ 226 #define FC_FC_RES_B17 (1 << 17) /* reserved */ 227 #define FC_FC_SEQ_INIT (1 << 16) /* transfer of sequence initiative */ 228 #define FC_FC_X_ID_REASS (1 << 15) /* exchange ID has been changed */ 229 #define FC_FC_X_ID_INVAL (1 << 14) /* exchange ID invalidated */ 230 231 #define FC_FC_ACK_1 (1 << 12) /* 13:12 = 1: ACK_1 expected */ 232 #define FC_FC_ACK_N (2 << 12) /* 13:12 = 2: ACK_N expected */ 233 #define FC_FC_ACK_0 (3 << 12) /* 13:12 = 3: ACK_0 expected */ 234 235 #define FC_FC_RES_B11 (1 << 11) /* reserved */ 236 #define FC_FC_RES_B10 (1 << 10) /* reserved */ 237 #define FC_FC_RETX_SEQ (1 << 9) /* retransmitted sequence */ 238 #define FC_FC_UNI_TX (1 << 8) /* unidirectional transmit (class 1) */ 239 #define FC_FC_CONT_SEQ(i) ((i) << 6) 240 #define FC_FC_ABT_SEQ(i) ((i) << 4) 241 #define FC_FC_REL_OFF (1 << 3) /* parameter is relative offset */ 242 #define FC_FC_RES2 (1 << 2) /* reserved */ 243 #define FC_FC_FILL(i) ((i) & 3) /* 1:0: bytes of trailing fill */ 244 245 /* 246 * BA_ACC payload. 247 */ 248 struct fc_ba_acc { 249 __u8 ba_seq_id_val; /* SEQ_ID validity */ 250 #define FC_BA_SEQ_ID_VAL 0x80 251 __u8 ba_seq_id; /* SEQ_ID of seq last deliverable */ 252 __u8 ba_resvd[2]; /* reserved */ 253 __be16 ba_ox_id; /* OX_ID for aborted seq or exch */ 254 __be16 ba_rx_id; /* RX_ID for aborted seq or exch */ 255 __be16 ba_low_seq_cnt; /* low SEQ_CNT of aborted seq */ 256 __be16 ba_high_seq_cnt; /* high SEQ_CNT of aborted seq */ 257 }; 258 259 /* 260 * BA_RJT: Basic Reject payload. 261 */ 262 struct fc_ba_rjt { 263 __u8 br_resvd; /* reserved */ 264 __u8 br_reason; /* reason code */ 265 __u8 br_explan; /* reason explanation */ 266 __u8 br_vendor; /* vendor unique code */ 267 }; 268 269 /* 270 * BA_RJT reason codes. 271 * From FS-2. 272 */ 273 enum fc_ba_rjt_reason { 274 FC_BA_RJT_NONE = 0, /* in software this means no reject */ 275 FC_BA_RJT_INVL_CMD = 0x01, /* invalid command code */ 276 FC_BA_RJT_LOG_ERR = 0x03, /* logical error */ 277 FC_BA_RJT_LOG_BUSY = 0x05, /* logical busy */ 278 FC_BA_RJT_PROTO_ERR = 0x07, /* protocol error */ 279 FC_BA_RJT_UNABLE = 0x09, /* unable to perform request */ 280 FC_BA_RJT_VENDOR = 0xff, /* vendor-specific (see br_vendor) */ 281 }; 282 283 /* 284 * BA_RJT reason code explanations. 285 */ 286 enum fc_ba_rjt_explan { 287 FC_BA_RJT_EXP_NONE = 0x00, /* no additional expanation */ 288 FC_BA_RJT_INV_XID = 0x03, /* invalid OX_ID-RX_ID combination */ 289 FC_BA_RJT_ABT = 0x05, /* sequence aborted, no seq info */ 290 }; 291 292 /* 293 * P_RJT or F_RJT: Port Reject or Fabric Reject parameter field. 294 */ 295 struct fc_pf_rjt { 296 __u8 rj_action; /* reserved */ 297 __u8 rj_reason; /* reason code */ 298 __u8 rj_resvd; /* reserved */ 299 __u8 rj_vendor; /* vendor unique code */ 300 }; 301 302 /* 303 * P_RJT and F_RJT reject reason codes. 304 */ 305 enum fc_pf_rjt_reason { 306 FC_RJT_NONE = 0, /* non-reject (reserved by standard) */ 307 FC_RJT_INVL_DID = 0x01, /* invalid destination ID */ 308 FC_RJT_INVL_SID = 0x02, /* invalid source ID */ 309 FC_RJT_P_UNAV_T = 0x03, /* port unavailable, temporary */ 310 FC_RJT_P_UNAV = 0x04, /* port unavailable, permanent */ 311 FC_RJT_CLS_UNSUP = 0x05, /* class not supported */ 312 FC_RJT_DEL_USAGE = 0x06, /* delimiter usage error */ 313 FC_RJT_TYPE_UNSUP = 0x07, /* type not supported */ 314 FC_RJT_LINK_CTL = 0x08, /* invalid link control */ 315 FC_RJT_R_CTL = 0x09, /* invalid R_CTL field */ 316 FC_RJT_F_CTL = 0x0a, /* invalid F_CTL field */ 317 FC_RJT_OX_ID = 0x0b, /* invalid originator exchange ID */ 318 FC_RJT_RX_ID = 0x0c, /* invalid responder exchange ID */ 319 FC_RJT_SEQ_ID = 0x0d, /* invalid sequence ID */ 320 FC_RJT_DF_CTL = 0x0e, /* invalid DF_CTL field */ 321 FC_RJT_SEQ_CNT = 0x0f, /* invalid SEQ_CNT field */ 322 FC_RJT_PARAM = 0x10, /* invalid parameter field */ 323 FC_RJT_EXCH_ERR = 0x11, /* exchange error */ 324 FC_RJT_PROTO = 0x12, /* protocol error */ 325 FC_RJT_LEN = 0x13, /* incorrect length */ 326 FC_RJT_UNEXP_ACK = 0x14, /* unexpected ACK */ 327 FC_RJT_FAB_CLASS = 0x15, /* class unsupported by fabric entity */ 328 FC_RJT_LOGI_REQ = 0x16, /* login required */ 329 FC_RJT_SEQ_XS = 0x17, /* excessive sequences attempted */ 330 FC_RJT_EXCH_EST = 0x18, /* unable to establish exchange */ 331 FC_RJT_FAB_UNAV = 0x1a, /* fabric unavailable */ 332 FC_RJT_VC_ID = 0x1b, /* invalid VC_ID (class 4) */ 333 FC_RJT_CS_CTL = 0x1c, /* invalid CS_CTL field */ 334 FC_RJT_INSUF_RES = 0x1d, /* insuff. resources for VC (Class 4) */ 335 FC_RJT_INVL_CLS = 0x1f, /* invalid class of service */ 336 FC_RJT_PREEMT_RJT = 0x20, /* preemption request rejected */ 337 FC_RJT_PREEMT_DIS = 0x21, /* preemption not enabled */ 338 FC_RJT_MCAST_ERR = 0x22, /* multicast error */ 339 FC_RJT_MCAST_ET = 0x23, /* multicast error terminate */ 340 FC_RJT_PRLI_REQ = 0x24, /* process login required */ 341 FC_RJT_INVL_ATT = 0x25, /* invalid attachment */ 342 FC_RJT_VENDOR = 0xff, /* vendor specific reject */ 343 }; 344 345 /* default timeout values */ 346 347 #define FC_DEF_E_D_TOV 2000UL 348 #define FC_DEF_R_A_TOV 10000UL 349 350 #endif /* _FC_FS_H_ */ 351