1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * mac80211 <-> driver interface 4 * 5 * Copyright 2002-2005, Devicescape Software, Inc. 6 * Copyright 2006-2007 Jiri Benc <jbenc@suse.cz> 7 * Copyright 2007-2010 Johannes Berg <johannes@sipsolutions.net> 8 * Copyright 2013-2014 Intel Mobile Communications GmbH 9 * Copyright (C) 2015 - 2017 Intel Deutschland GmbH 10 * Copyright (C) 2018 - 2021 Intel Corporation 11 */ 12 13 #ifndef MAC80211_H 14 #define MAC80211_H 15 16 #include <linux/bug.h> 17 #include <linux/kernel.h> 18 #include <linux/if_ether.h> 19 #include <linux/skbuff.h> 20 #include <linux/ieee80211.h> 21 #include <net/cfg80211.h> 22 #include <net/codel.h> 23 #include <net/ieee80211_radiotap.h> 24 #include <asm/unaligned.h> 25 26 /** 27 * DOC: Introduction 28 * 29 * mac80211 is the Linux stack for 802.11 hardware that implements 30 * only partial functionality in hard- or firmware. This document 31 * defines the interface between mac80211 and low-level hardware 32 * drivers. 33 */ 34 35 /** 36 * DOC: Calling mac80211 from interrupts 37 * 38 * Only ieee80211_tx_status_irqsafe() and ieee80211_rx_irqsafe() can be 39 * called in hardware interrupt context. The low-level driver must not call any 40 * other functions in hardware interrupt context. If there is a need for such 41 * call, the low-level driver should first ACK the interrupt and perform the 42 * IEEE 802.11 code call after this, e.g. from a scheduled workqueue or even 43 * tasklet function. 44 * 45 * NOTE: If the driver opts to use the _irqsafe() functions, it may not also 46 * use the non-IRQ-safe functions! 47 */ 48 49 /** 50 * DOC: Warning 51 * 52 * If you're reading this document and not the header file itself, it will 53 * be incomplete because not all documentation has been converted yet. 54 */ 55 56 /** 57 * DOC: Frame format 58 * 59 * As a general rule, when frames are passed between mac80211 and the driver, 60 * they start with the IEEE 802.11 header and include the same octets that are 61 * sent over the air except for the FCS which should be calculated by the 62 * hardware. 63 * 64 * There are, however, various exceptions to this rule for advanced features: 65 * 66 * The first exception is for hardware encryption and decryption offload 67 * where the IV/ICV may or may not be generated in hardware. 68 * 69 * Secondly, when the hardware handles fragmentation, the frame handed to 70 * the driver from mac80211 is the MSDU, not the MPDU. 71 */ 72 73 /** 74 * DOC: mac80211 workqueue 75 * 76 * mac80211 provides its own workqueue for drivers and internal mac80211 use. 77 * The workqueue is a single threaded workqueue and can only be accessed by 78 * helpers for sanity checking. Drivers must ensure all work added onto the 79 * mac80211 workqueue should be cancelled on the driver stop() callback. 80 * 81 * mac80211 will flushed the workqueue upon interface removal and during 82 * suspend. 83 * 84 * All work performed on the mac80211 workqueue must not acquire the RTNL lock. 85 * 86 */ 87 88 /** 89 * DOC: mac80211 software tx queueing 90 * 91 * mac80211 provides an optional intermediate queueing implementation designed 92 * to allow the driver to keep hardware queues short and provide some fairness 93 * between different stations/interfaces. 94 * In this model, the driver pulls data frames from the mac80211 queue instead 95 * of letting mac80211 push them via drv_tx(). 96 * Other frames (e.g. control or management) are still pushed using drv_tx(). 97 * 98 * Drivers indicate that they use this model by implementing the .wake_tx_queue 99 * driver operation. 100 * 101 * Intermediate queues (struct ieee80211_txq) are kept per-sta per-tid, with 102 * another per-sta for non-data/non-mgmt and bufferable management frames, and 103 * a single per-vif queue for multicast data frames. 104 * 105 * The driver is expected to initialize its private per-queue data for stations 106 * and interfaces in the .add_interface and .sta_add ops. 107 * 108 * The driver can't access the queue directly. To dequeue a frame from a 109 * txq, it calls ieee80211_tx_dequeue(). Whenever mac80211 adds a new frame to a 110 * queue, it calls the .wake_tx_queue driver op. 111 * 112 * Drivers can optionally delegate responsibility for scheduling queues to 113 * mac80211, to take advantage of airtime fairness accounting. In this case, to 114 * obtain the next queue to pull frames from, the driver calls 115 * ieee80211_next_txq(). The driver is then expected to return the txq using 116 * ieee80211_return_txq(). 117 * 118 * For AP powersave TIM handling, the driver only needs to indicate if it has 119 * buffered packets in the driver specific data structures by calling 120 * ieee80211_sta_set_buffered(). For frames buffered in the ieee80211_txq 121 * struct, mac80211 sets the appropriate TIM PVB bits and calls 122 * .release_buffered_frames(). 123 * In that callback the driver is therefore expected to release its own 124 * buffered frames and afterwards also frames from the ieee80211_txq (obtained 125 * via the usual ieee80211_tx_dequeue). 126 */ 127 128 struct device; 129 130 /** 131 * enum ieee80211_max_queues - maximum number of queues 132 * 133 * @IEEE80211_MAX_QUEUES: Maximum number of regular device queues. 134 * @IEEE80211_MAX_QUEUE_MAP: bitmap with maximum queues set 135 */ 136 enum ieee80211_max_queues { 137 IEEE80211_MAX_QUEUES = 16, 138 IEEE80211_MAX_QUEUE_MAP = BIT(IEEE80211_MAX_QUEUES) - 1, 139 }; 140 141 #define IEEE80211_INVAL_HW_QUEUE 0xff 142 143 /** 144 * enum ieee80211_ac_numbers - AC numbers as used in mac80211 145 * @IEEE80211_AC_VO: voice 146 * @IEEE80211_AC_VI: video 147 * @IEEE80211_AC_BE: best effort 148 * @IEEE80211_AC_BK: background 149 */ 150 enum ieee80211_ac_numbers { 151 IEEE80211_AC_VO = 0, 152 IEEE80211_AC_VI = 1, 153 IEEE80211_AC_BE = 2, 154 IEEE80211_AC_BK = 3, 155 }; 156 157 /** 158 * struct ieee80211_tx_queue_params - transmit queue configuration 159 * 160 * The information provided in this structure is required for QoS 161 * transmit queue configuration. Cf. IEEE 802.11 7.3.2.29. 162 * 163 * @aifs: arbitration interframe space [0..255] 164 * @cw_min: minimum contention window [a value of the form 165 * 2^n-1 in the range 1..32767] 166 * @cw_max: maximum contention window [like @cw_min] 167 * @txop: maximum burst time in units of 32 usecs, 0 meaning disabled 168 * @acm: is mandatory admission control required for the access category 169 * @uapsd: is U-APSD mode enabled for the queue 170 * @mu_edca: is the MU EDCA configured 171 * @mu_edca_param_rec: MU EDCA Parameter Record for HE 172 */ 173 struct ieee80211_tx_queue_params { 174 u16 txop; 175 u16 cw_min; 176 u16 cw_max; 177 u8 aifs; 178 bool acm; 179 bool uapsd; 180 bool mu_edca; 181 struct ieee80211_he_mu_edca_param_ac_rec mu_edca_param_rec; 182 }; 183 184 struct ieee80211_low_level_stats { 185 unsigned int dot11ACKFailureCount; 186 unsigned int dot11RTSFailureCount; 187 unsigned int dot11FCSErrorCount; 188 unsigned int dot11RTSSuccessCount; 189 }; 190 191 /** 192 * enum ieee80211_chanctx_change - change flag for channel context 193 * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed 194 * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed 195 * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed 196 * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel, 197 * this is used only with channel switching with CSA 198 * @IEEE80211_CHANCTX_CHANGE_MIN_WIDTH: The min required channel width changed 199 */ 200 enum ieee80211_chanctx_change { 201 IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0), 202 IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1), 203 IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2), 204 IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3), 205 IEEE80211_CHANCTX_CHANGE_MIN_WIDTH = BIT(4), 206 }; 207 208 /** 209 * struct ieee80211_chanctx_conf - channel context that vifs may be tuned to 210 * 211 * This is the driver-visible part. The ieee80211_chanctx 212 * that contains it is visible in mac80211 only. 213 * 214 * @def: the channel definition 215 * @min_def: the minimum channel definition currently required. 216 * @rx_chains_static: The number of RX chains that must always be 217 * active on the channel to receive MIMO transmissions 218 * @rx_chains_dynamic: The number of RX chains that must be enabled 219 * after RTS/CTS handshake to receive SMPS MIMO transmissions; 220 * this will always be >= @rx_chains_static. 221 * @radar_enabled: whether radar detection is enabled on this channel. 222 * @drv_priv: data area for driver use, will always be aligned to 223 * sizeof(void *), size is determined in hw information. 224 */ 225 struct ieee80211_chanctx_conf { 226 struct cfg80211_chan_def def; 227 struct cfg80211_chan_def min_def; 228 229 u8 rx_chains_static, rx_chains_dynamic; 230 231 bool radar_enabled; 232 233 u8 drv_priv[] __aligned(sizeof(void *)); 234 }; 235 236 /** 237 * enum ieee80211_chanctx_switch_mode - channel context switch mode 238 * @CHANCTX_SWMODE_REASSIGN_VIF: Both old and new contexts already 239 * exist (and will continue to exist), but the virtual interface 240 * needs to be switched from one to the other. 241 * @CHANCTX_SWMODE_SWAP_CONTEXTS: The old context exists but will stop 242 * to exist with this call, the new context doesn't exist but 243 * will be active after this call, the virtual interface switches 244 * from the old to the new (note that the driver may of course 245 * implement this as an on-the-fly chandef switch of the existing 246 * hardware context, but the mac80211 pointer for the old context 247 * will cease to exist and only the new one will later be used 248 * for changes/removal.) 249 */ 250 enum ieee80211_chanctx_switch_mode { 251 CHANCTX_SWMODE_REASSIGN_VIF, 252 CHANCTX_SWMODE_SWAP_CONTEXTS, 253 }; 254 255 /** 256 * struct ieee80211_vif_chanctx_switch - vif chanctx switch information 257 * 258 * This is structure is used to pass information about a vif that 259 * needs to switch from one chanctx to another. The 260 * &ieee80211_chanctx_switch_mode defines how the switch should be 261 * done. 262 * 263 * @vif: the vif that should be switched from old_ctx to new_ctx 264 * @old_ctx: the old context to which the vif was assigned 265 * @new_ctx: the new context to which the vif must be assigned 266 */ 267 struct ieee80211_vif_chanctx_switch { 268 struct ieee80211_vif *vif; 269 struct ieee80211_chanctx_conf *old_ctx; 270 struct ieee80211_chanctx_conf *new_ctx; 271 }; 272 273 /** 274 * enum ieee80211_bss_change - BSS change notification flags 275 * 276 * These flags are used with the bss_info_changed() callback 277 * to indicate which BSS parameter changed. 278 * 279 * @BSS_CHANGED_ASSOC: association status changed (associated/disassociated), 280 * also implies a change in the AID. 281 * @BSS_CHANGED_ERP_CTS_PROT: CTS protection changed 282 * @BSS_CHANGED_ERP_PREAMBLE: preamble changed 283 * @BSS_CHANGED_ERP_SLOT: slot timing changed 284 * @BSS_CHANGED_HT: 802.11n parameters changed 285 * @BSS_CHANGED_BASIC_RATES: Basic rateset changed 286 * @BSS_CHANGED_BEACON_INT: Beacon interval changed 287 * @BSS_CHANGED_BSSID: BSSID changed, for whatever 288 * reason (IBSS and managed mode) 289 * @BSS_CHANGED_BEACON: Beacon data changed, retrieve 290 * new beacon (beaconing modes) 291 * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be 292 * enabled/disabled (beaconing modes) 293 * @BSS_CHANGED_CQM: Connection quality monitor config changed 294 * @BSS_CHANGED_IBSS: IBSS join status changed 295 * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed. 296 * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note 297 * that it is only ever disabled for station mode. 298 * @BSS_CHANGED_IDLE: Idle changed for this BSS/interface. 299 * @BSS_CHANGED_SSID: SSID changed for this BSS (AP and IBSS mode) 300 * @BSS_CHANGED_AP_PROBE_RESP: Probe Response changed for this BSS (AP mode) 301 * @BSS_CHANGED_PS: PS changed for this BSS (STA mode) 302 * @BSS_CHANGED_TXPOWER: TX power setting changed for this interface 303 * @BSS_CHANGED_P2P_PS: P2P powersave settings (CTWindow, opportunistic PS) 304 * changed 305 * @BSS_CHANGED_BEACON_INFO: Data from the AP's beacon became available: 306 * currently dtim_period only is under consideration. 307 * @BSS_CHANGED_BANDWIDTH: The bandwidth used by this interface changed, 308 * note that this is only called when it changes after the channel 309 * context had been assigned. 310 * @BSS_CHANGED_OCB: OCB join status changed 311 * @BSS_CHANGED_MU_GROUPS: VHT MU-MIMO group id or user position changed 312 * @BSS_CHANGED_KEEP_ALIVE: keep alive options (idle period or protected 313 * keep alive) changed. 314 * @BSS_CHANGED_MCAST_RATE: Multicast Rate setting changed for this interface 315 * @BSS_CHANGED_FTM_RESPONDER: fine timing measurement request responder 316 * functionality changed for this BSS (AP mode). 317 * @BSS_CHANGED_TWT: TWT status changed 318 * @BSS_CHANGED_HE_OBSS_PD: OBSS Packet Detection status changed. 319 * @BSS_CHANGED_HE_BSS_COLOR: BSS Color has changed 320 * @BSS_CHANGED_FILS_DISCOVERY: FILS discovery status changed. 321 * @BSS_CHANGED_UNSOL_BCAST_PROBE_RESP: Unsolicited broadcast probe response 322 * status changed. 323 * 324 */ 325 enum ieee80211_bss_change { 326 BSS_CHANGED_ASSOC = 1<<0, 327 BSS_CHANGED_ERP_CTS_PROT = 1<<1, 328 BSS_CHANGED_ERP_PREAMBLE = 1<<2, 329 BSS_CHANGED_ERP_SLOT = 1<<3, 330 BSS_CHANGED_HT = 1<<4, 331 BSS_CHANGED_BASIC_RATES = 1<<5, 332 BSS_CHANGED_BEACON_INT = 1<<6, 333 BSS_CHANGED_BSSID = 1<<7, 334 BSS_CHANGED_BEACON = 1<<8, 335 BSS_CHANGED_BEACON_ENABLED = 1<<9, 336 BSS_CHANGED_CQM = 1<<10, 337 BSS_CHANGED_IBSS = 1<<11, 338 BSS_CHANGED_ARP_FILTER = 1<<12, 339 BSS_CHANGED_QOS = 1<<13, 340 BSS_CHANGED_IDLE = 1<<14, 341 BSS_CHANGED_SSID = 1<<15, 342 BSS_CHANGED_AP_PROBE_RESP = 1<<16, 343 BSS_CHANGED_PS = 1<<17, 344 BSS_CHANGED_TXPOWER = 1<<18, 345 BSS_CHANGED_P2P_PS = 1<<19, 346 BSS_CHANGED_BEACON_INFO = 1<<20, 347 BSS_CHANGED_BANDWIDTH = 1<<21, 348 BSS_CHANGED_OCB = 1<<22, 349 BSS_CHANGED_MU_GROUPS = 1<<23, 350 BSS_CHANGED_KEEP_ALIVE = 1<<24, 351 BSS_CHANGED_MCAST_RATE = 1<<25, 352 BSS_CHANGED_FTM_RESPONDER = 1<<26, 353 BSS_CHANGED_TWT = 1<<27, 354 BSS_CHANGED_HE_OBSS_PD = 1<<28, 355 BSS_CHANGED_HE_BSS_COLOR = 1<<29, 356 BSS_CHANGED_FILS_DISCOVERY = 1<<30, 357 BSS_CHANGED_UNSOL_BCAST_PROBE_RESP = 1<<31, 358 359 /* when adding here, make sure to change ieee80211_reconfig */ 360 }; 361 362 /* 363 * The maximum number of IPv4 addresses listed for ARP filtering. If the number 364 * of addresses for an interface increase beyond this value, hardware ARP 365 * filtering will be disabled. 366 */ 367 #define IEEE80211_BSS_ARP_ADDR_LIST_LEN 4 368 369 /** 370 * enum ieee80211_event_type - event to be notified to the low level driver 371 * @RSSI_EVENT: AP's rssi crossed the a threshold set by the driver. 372 * @MLME_EVENT: event related to MLME 373 * @BAR_RX_EVENT: a BAR was received 374 * @BA_FRAME_TIMEOUT: Frames were released from the reordering buffer because 375 * they timed out. This won't be called for each frame released, but only 376 * once each time the timeout triggers. 377 */ 378 enum ieee80211_event_type { 379 RSSI_EVENT, 380 MLME_EVENT, 381 BAR_RX_EVENT, 382 BA_FRAME_TIMEOUT, 383 }; 384 385 /** 386 * enum ieee80211_rssi_event_data - relevant when event type is %RSSI_EVENT 387 * @RSSI_EVENT_HIGH: AP's rssi went below the threshold set by the driver. 388 * @RSSI_EVENT_LOW: AP's rssi went above the threshold set by the driver. 389 */ 390 enum ieee80211_rssi_event_data { 391 RSSI_EVENT_HIGH, 392 RSSI_EVENT_LOW, 393 }; 394 395 /** 396 * struct ieee80211_rssi_event - data attached to an %RSSI_EVENT 397 * @data: See &enum ieee80211_rssi_event_data 398 */ 399 struct ieee80211_rssi_event { 400 enum ieee80211_rssi_event_data data; 401 }; 402 403 /** 404 * enum ieee80211_mlme_event_data - relevant when event type is %MLME_EVENT 405 * @AUTH_EVENT: the MLME operation is authentication 406 * @ASSOC_EVENT: the MLME operation is association 407 * @DEAUTH_RX_EVENT: deauth received.. 408 * @DEAUTH_TX_EVENT: deauth sent. 409 */ 410 enum ieee80211_mlme_event_data { 411 AUTH_EVENT, 412 ASSOC_EVENT, 413 DEAUTH_RX_EVENT, 414 DEAUTH_TX_EVENT, 415 }; 416 417 /** 418 * enum ieee80211_mlme_event_status - relevant when event type is %MLME_EVENT 419 * @MLME_SUCCESS: the MLME operation completed successfully. 420 * @MLME_DENIED: the MLME operation was denied by the peer. 421 * @MLME_TIMEOUT: the MLME operation timed out. 422 */ 423 enum ieee80211_mlme_event_status { 424 MLME_SUCCESS, 425 MLME_DENIED, 426 MLME_TIMEOUT, 427 }; 428 429 /** 430 * struct ieee80211_mlme_event - data attached to an %MLME_EVENT 431 * @data: See &enum ieee80211_mlme_event_data 432 * @status: See &enum ieee80211_mlme_event_status 433 * @reason: the reason code if applicable 434 */ 435 struct ieee80211_mlme_event { 436 enum ieee80211_mlme_event_data data; 437 enum ieee80211_mlme_event_status status; 438 u16 reason; 439 }; 440 441 /** 442 * struct ieee80211_ba_event - data attached for BlockAck related events 443 * @sta: pointer to the &ieee80211_sta to which this event relates 444 * @tid: the tid 445 * @ssn: the starting sequence number (for %BAR_RX_EVENT) 446 */ 447 struct ieee80211_ba_event { 448 struct ieee80211_sta *sta; 449 u16 tid; 450 u16 ssn; 451 }; 452 453 /** 454 * struct ieee80211_event - event to be sent to the driver 455 * @type: The event itself. See &enum ieee80211_event_type. 456 * @rssi: relevant if &type is %RSSI_EVENT 457 * @mlme: relevant if &type is %AUTH_EVENT 458 * @ba: relevant if &type is %BAR_RX_EVENT or %BA_FRAME_TIMEOUT 459 * @u:union holding the fields above 460 */ 461 struct ieee80211_event { 462 enum ieee80211_event_type type; 463 union { 464 struct ieee80211_rssi_event rssi; 465 struct ieee80211_mlme_event mlme; 466 struct ieee80211_ba_event ba; 467 } u; 468 }; 469 470 /** 471 * struct ieee80211_mu_group_data - STA's VHT MU-MIMO group data 472 * 473 * This structure describes the group id data of VHT MU-MIMO 474 * 475 * @membership: 64 bits array - a bit is set if station is member of the group 476 * @position: 2 bits per group id indicating the position in the group 477 */ 478 struct ieee80211_mu_group_data { 479 u8 membership[WLAN_MEMBERSHIP_LEN]; 480 u8 position[WLAN_USER_POSITION_LEN]; 481 }; 482 483 /** 484 * struct ieee80211_ftm_responder_params - FTM responder parameters 485 * 486 * @lci: LCI subelement content 487 * @civicloc: CIVIC location subelement content 488 * @lci_len: LCI data length 489 * @civicloc_len: Civic data length 490 */ 491 struct ieee80211_ftm_responder_params { 492 const u8 *lci; 493 const u8 *civicloc; 494 size_t lci_len; 495 size_t civicloc_len; 496 }; 497 498 /** 499 * struct ieee80211_fils_discovery - FILS discovery parameters from 500 * IEEE Std 802.11ai-2016, Annex C.3 MIB detail. 501 * 502 * @min_interval: Minimum packet interval in TUs (0 - 10000) 503 * @max_interval: Maximum packet interval in TUs (0 - 10000) 504 */ 505 struct ieee80211_fils_discovery { 506 u32 min_interval; 507 u32 max_interval; 508 }; 509 510 /** 511 * struct ieee80211_bss_conf - holds the BSS's changing parameters 512 * 513 * This structure keeps information about a BSS (and an association 514 * to that BSS) that can change during the lifetime of the BSS. 515 * 516 * @htc_trig_based_pkt_ext: default PE in 4us units, if BSS supports HE 517 * @multi_sta_back_32bit: supports BA bitmap of 32-bits in Multi-STA BACK 518 * @uora_exists: is the UORA element advertised by AP 519 * @ack_enabled: indicates support to receive a multi-TID that solicits either 520 * ACK, BACK or both 521 * @uora_ocw_range: UORA element's OCW Range field 522 * @frame_time_rts_th: HE duration RTS threshold, in units of 32us 523 * @he_support: does this BSS support HE 524 * @twt_requester: does this BSS support TWT requester (relevant for managed 525 * mode only, set if the AP advertises TWT responder role) 526 * @twt_responder: does this BSS support TWT requester (relevant for managed 527 * mode only, set if the AP advertises TWT responder role) 528 * @twt_protected: does this BSS support protected TWT frames 529 * @twt_broadcast: does this BSS support broadcast TWT 530 * @assoc: association status 531 * @ibss_joined: indicates whether this station is part of an IBSS 532 * or not 533 * @ibss_creator: indicates if a new IBSS network is being created 534 * @aid: association ID number, valid only when @assoc is true 535 * @use_cts_prot: use CTS protection 536 * @use_short_preamble: use 802.11b short preamble 537 * @use_short_slot: use short slot time (only relevant for ERP) 538 * @dtim_period: num of beacons before the next DTIM, for beaconing, 539 * valid in station mode only if after the driver was notified 540 * with the %BSS_CHANGED_BEACON_INFO flag, will be non-zero then. 541 * @sync_tsf: last beacon's/probe response's TSF timestamp (could be old 542 * as it may have been received during scanning long ago). If the 543 * HW flag %IEEE80211_HW_TIMING_BEACON_ONLY is set, then this can 544 * only come from a beacon, but might not become valid until after 545 * association when a beacon is received (which is notified with the 546 * %BSS_CHANGED_DTIM flag.). See also sync_dtim_count important notice. 547 * @sync_device_ts: the device timestamp corresponding to the sync_tsf, 548 * the driver/device can use this to calculate synchronisation 549 * (see @sync_tsf). See also sync_dtim_count important notice. 550 * @sync_dtim_count: Only valid when %IEEE80211_HW_TIMING_BEACON_ONLY 551 * is requested, see @sync_tsf/@sync_device_ts. 552 * IMPORTANT: These three sync_* parameters would possibly be out of sync 553 * by the time the driver will use them. The synchronized view is currently 554 * guaranteed only in certain callbacks. 555 * @beacon_int: beacon interval 556 * @assoc_capability: capabilities taken from assoc resp 557 * @basic_rates: bitmap of basic rates, each bit stands for an 558 * index into the rate table configured by the driver in 559 * the current band. 560 * @beacon_rate: associated AP's beacon TX rate 561 * @mcast_rate: per-band multicast rate index + 1 (0: disabled) 562 * @bssid: The BSSID for this BSS 563 * @enable_beacon: whether beaconing should be enabled or not 564 * @chandef: Channel definition for this BSS -- the hardware might be 565 * configured a higher bandwidth than this BSS uses, for example. 566 * @mu_group: VHT MU-MIMO group membership data 567 * @ht_operation_mode: HT operation mode like in &struct ieee80211_ht_operation. 568 * This field is only valid when the channel is a wide HT/VHT channel. 569 * Note that with TDLS this can be the case (channel is HT, protection must 570 * be used from this field) even when the BSS association isn't using HT. 571 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value 572 * implies disabled. As with the cfg80211 callback, a change here should 573 * cause an event to be sent indicating where the current value is in 574 * relation to the newly configured threshold. 575 * @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value 576 * implies disabled. This is an alternative mechanism to the single 577 * threshold event and can't be enabled simultaneously with it. 578 * @cqm_rssi_high: Connection quality monitor RSSI upper threshold. 579 * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis 580 * @arp_addr_list: List of IPv4 addresses for hardware ARP filtering. The 581 * may filter ARP queries targeted for other addresses than listed here. 582 * The driver must allow ARP queries targeted for all address listed here 583 * to pass through. An empty list implies no ARP queries need to pass. 584 * @arp_addr_cnt: Number of addresses currently on the list. Note that this 585 * may be larger than %IEEE80211_BSS_ARP_ADDR_LIST_LEN (the arp_addr_list 586 * array size), it's up to the driver what to do in that case. 587 * @qos: This is a QoS-enabled BSS. 588 * @idle: This interface is idle. There's also a global idle flag in the 589 * hardware config which may be more appropriate depending on what 590 * your driver/device needs to do. 591 * @ps: power-save mode (STA only). This flag is NOT affected by 592 * offchannel/dynamic_ps operations. 593 * @ssid: The SSID of the current vif. Valid in AP and IBSS mode. 594 * @ssid_len: Length of SSID given in @ssid. 595 * @hidden_ssid: The SSID of the current vif is hidden. Only valid in AP-mode. 596 * @txpower: TX power in dBm. INT_MIN means not configured. 597 * @txpower_type: TX power adjustment used to control per packet Transmit 598 * Power Control (TPC) in lower driver for the current vif. In particular 599 * TPC is enabled if value passed in %txpower_type is 600 * NL80211_TX_POWER_LIMITED (allow using less than specified from 601 * userspace), whereas TPC is disabled if %txpower_type is set to 602 * NL80211_TX_POWER_FIXED (use value configured from userspace) 603 * @p2p_noa_attr: P2P NoA attribute for P2P powersave 604 * @allow_p2p_go_ps: indication for AP or P2P GO interface, whether it's allowed 605 * to use P2P PS mechanism or not. AP/P2P GO is not allowed to use P2P PS 606 * if it has associated clients without P2P PS support. 607 * @max_idle_period: the time period during which the station can refrain from 608 * transmitting frames to its associated AP without being disassociated. 609 * In units of 1000 TUs. Zero value indicates that the AP did not include 610 * a (valid) BSS Max Idle Period Element. 611 * @protected_keep_alive: if set, indicates that the station should send an RSN 612 * protected frame to the AP to reset the idle timer at the AP for the 613 * station. 614 * @ftm_responder: whether to enable or disable fine timing measurement FTM 615 * responder functionality. 616 * @ftmr_params: configurable lci/civic parameter when enabling FTM responder. 617 * @nontransmitted: this BSS is a nontransmitted BSS profile 618 * @transmitter_bssid: the address of transmitter AP 619 * @bssid_index: index inside the multiple BSSID set 620 * @bssid_indicator: 2^bssid_indicator is the maximum number of APs in set 621 * @ema_ap: AP supports enhancements of discovery and advertisement of 622 * nontransmitted BSSIDs 623 * @profile_periodicity: the least number of beacon frames need to be received 624 * in order to discover all the nontransmitted BSSIDs in the set. 625 * @he_oper: HE operation information of the BSS (AP/Mesh) or of the AP we are 626 * connected to (STA) 627 * @he_obss_pd: OBSS Packet Detection parameters. 628 * @he_bss_color: BSS coloring settings, if BSS supports HE 629 * @fils_discovery: FILS discovery configuration 630 * @unsol_bcast_probe_resp_interval: Unsolicited broadcast probe response 631 * interval. 632 * @s1g: BSS is S1G BSS (affects Association Request format). 633 * @beacon_tx_rate: The configured beacon transmit rate that needs to be passed 634 * to driver when rate control is offloaded to firmware. 635 */ 636 struct ieee80211_bss_conf { 637 const u8 *bssid; 638 u8 htc_trig_based_pkt_ext; 639 bool uora_exists; 640 u8 uora_ocw_range; 641 u16 frame_time_rts_th; 642 bool he_support; 643 bool twt_requester; 644 bool twt_responder; 645 bool twt_protected; 646 bool twt_broadcast; 647 /* association related data */ 648 bool assoc, ibss_joined; 649 bool ibss_creator; 650 u16 aid; 651 /* erp related data */ 652 bool use_cts_prot; 653 bool use_short_preamble; 654 bool use_short_slot; 655 bool enable_beacon; 656 u8 dtim_period; 657 u16 beacon_int; 658 u16 assoc_capability; 659 u64 sync_tsf; 660 u32 sync_device_ts; 661 u8 sync_dtim_count; 662 u32 basic_rates; 663 struct ieee80211_rate *beacon_rate; 664 int mcast_rate[NUM_NL80211_BANDS]; 665 u16 ht_operation_mode; 666 s32 cqm_rssi_thold; 667 u32 cqm_rssi_hyst; 668 s32 cqm_rssi_low; 669 s32 cqm_rssi_high; 670 struct cfg80211_chan_def chandef; 671 struct ieee80211_mu_group_data mu_group; 672 __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN]; 673 int arp_addr_cnt; 674 bool qos; 675 bool idle; 676 bool ps; 677 u8 ssid[IEEE80211_MAX_SSID_LEN]; 678 size_t ssid_len; 679 bool hidden_ssid; 680 int txpower; 681 enum nl80211_tx_power_setting txpower_type; 682 struct ieee80211_p2p_noa_attr p2p_noa_attr; 683 bool allow_p2p_go_ps; 684 u16 max_idle_period; 685 bool protected_keep_alive; 686 bool ftm_responder; 687 struct ieee80211_ftm_responder_params *ftmr_params; 688 /* Multiple BSSID data */ 689 bool nontransmitted; 690 u8 transmitter_bssid[ETH_ALEN]; 691 u8 bssid_index; 692 u8 bssid_indicator; 693 bool ema_ap; 694 u8 profile_periodicity; 695 struct { 696 u32 params; 697 u16 nss_set; 698 } he_oper; 699 struct ieee80211_he_obss_pd he_obss_pd; 700 struct cfg80211_he_bss_color he_bss_color; 701 struct ieee80211_fils_discovery fils_discovery; 702 u32 unsol_bcast_probe_resp_interval; 703 bool s1g; 704 struct cfg80211_bitrate_mask beacon_tx_rate; 705 }; 706 707 /** 708 * enum mac80211_tx_info_flags - flags to describe transmission information/status 709 * 710 * These flags are used with the @flags member of &ieee80211_tx_info. 711 * 712 * @IEEE80211_TX_CTL_REQ_TX_STATUS: require TX status callback for this frame. 713 * @IEEE80211_TX_CTL_ASSIGN_SEQ: The driver has to assign a sequence 714 * number to this frame, taking care of not overwriting the fragment 715 * number and increasing the sequence number only when the 716 * IEEE80211_TX_CTL_FIRST_FRAGMENT flag is set. mac80211 will properly 717 * assign sequence numbers to QoS-data frames but cannot do so correctly 718 * for non-QoS-data and management frames because beacons need them from 719 * that counter as well and mac80211 cannot guarantee proper sequencing. 720 * If this flag is set, the driver should instruct the hardware to 721 * assign a sequence number to the frame or assign one itself. Cf. IEEE 722 * 802.11-2007 7.1.3.4.1 paragraph 3. This flag will always be set for 723 * beacons and always be clear for frames without a sequence number field. 724 * @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack 725 * @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination 726 * station 727 * @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame 728 * @IEEE80211_TX_CTL_SEND_AFTER_DTIM: send this frame after DTIM beacon 729 * @IEEE80211_TX_CTL_AMPDU: this frame should be sent as part of an A-MPDU 730 * @IEEE80211_TX_CTL_INJECTED: Frame was injected, internal to mac80211. 731 * @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted 732 * because the destination STA was in powersave mode. Note that to 733 * avoid race conditions, the filter must be set by the hardware or 734 * firmware upon receiving a frame that indicates that the station 735 * went to sleep (must be done on device to filter frames already on 736 * the queue) and may only be unset after mac80211 gives the OK for 737 * that by setting the IEEE80211_TX_CTL_CLEAR_PS_FILT (see above), 738 * since only then is it guaranteed that no more frames are in the 739 * hardware queue. 740 * @IEEE80211_TX_STAT_ACK: Frame was acknowledged 741 * @IEEE80211_TX_STAT_AMPDU: The frame was aggregated, so status 742 * is for the whole aggregation. 743 * @IEEE80211_TX_STAT_AMPDU_NO_BACK: no block ack was returned, 744 * so consider using block ack request (BAR). 745 * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: internal to mac80211, can be 746 * set by rate control algorithms to indicate probe rate, will 747 * be cleared for fragmented frames (except on the last fragment) 748 * @IEEE80211_TX_INTFL_OFFCHAN_TX_OK: Internal to mac80211. Used to indicate 749 * that a frame can be transmitted while the queues are stopped for 750 * off-channel operation. 751 * @IEEE80211_TX_CTL_HW_80211_ENCAP: This frame uses hardware encapsulation 752 * (header conversion) 753 * @IEEE80211_TX_INTFL_RETRIED: completely internal to mac80211, 754 * used to indicate that a frame was already retried due to PS 755 * @IEEE80211_TX_INTFL_DONT_ENCRYPT: completely internal to mac80211, 756 * used to indicate frame should not be encrypted 757 * @IEEE80211_TX_CTL_NO_PS_BUFFER: This frame is a response to a poll 758 * frame (PS-Poll or uAPSD) or a non-bufferable MMPDU and must 759 * be sent although the station is in powersave mode. 760 * @IEEE80211_TX_CTL_MORE_FRAMES: More frames will be passed to the 761 * transmit function after the current frame, this can be used 762 * by drivers to kick the DMA queue only if unset or when the 763 * queue gets full. 764 * @IEEE80211_TX_INTFL_RETRANSMISSION: This frame is being retransmitted 765 * after TX status because the destination was asleep, it must not 766 * be modified again (no seqno assignment, crypto, etc.) 767 * @IEEE80211_TX_INTFL_MLME_CONN_TX: This frame was transmitted by the MLME 768 * code for connection establishment, this indicates that its status 769 * should kick the MLME state machine. 770 * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211 771 * MLME command (internal to mac80211 to figure out whether to send TX 772 * status to user space) 773 * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame 774 * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this 775 * frame and selects the maximum number of streams that it can use. 776 * @IEEE80211_TX_CTL_TX_OFFCHAN: Marks this packet to be transmitted on 777 * the off-channel channel when a remain-on-channel offload is done 778 * in hardware -- normal packets still flow and are expected to be 779 * handled properly by the device. 780 * @IEEE80211_TX_INTFL_TKIP_MIC_FAILURE: Marks this packet to be used for TKIP 781 * testing. It will be sent out with incorrect Michael MIC key to allow 782 * TKIP countermeasures to be tested. 783 * @IEEE80211_TX_CTL_NO_CCK_RATE: This frame will be sent at non CCK rate. 784 * This flag is actually used for management frame especially for P2P 785 * frames not being sent at CCK rate in 2GHz band. 786 * @IEEE80211_TX_STATUS_EOSP: This packet marks the end of service period, 787 * when its status is reported the service period ends. For frames in 788 * an SP that mac80211 transmits, it is already set; for driver frames 789 * the driver may set this flag. It is also used to do the same for 790 * PS-Poll responses. 791 * @IEEE80211_TX_CTL_USE_MINRATE: This frame will be sent at lowest rate. 792 * This flag is used to send nullfunc frame at minimum rate when 793 * the nullfunc is used for connection monitoring purpose. 794 * @IEEE80211_TX_CTL_DONTFRAG: Don't fragment this packet even if it 795 * would be fragmented by size (this is optional, only used for 796 * monitor injection). 797 * @IEEE80211_TX_STAT_NOACK_TRANSMITTED: A frame that was marked with 798 * IEEE80211_TX_CTL_NO_ACK has been successfully transmitted without 799 * any errors (like issues specific to the driver/HW). 800 * This flag must not be set for frames that don't request no-ack 801 * behaviour with IEEE80211_TX_CTL_NO_ACK. 802 * 803 * Note: If you have to add new flags to the enumeration, then don't 804 * forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary. 805 */ 806 enum mac80211_tx_info_flags { 807 IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), 808 IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1), 809 IEEE80211_TX_CTL_NO_ACK = BIT(2), 810 IEEE80211_TX_CTL_CLEAR_PS_FILT = BIT(3), 811 IEEE80211_TX_CTL_FIRST_FRAGMENT = BIT(4), 812 IEEE80211_TX_CTL_SEND_AFTER_DTIM = BIT(5), 813 IEEE80211_TX_CTL_AMPDU = BIT(6), 814 IEEE80211_TX_CTL_INJECTED = BIT(7), 815 IEEE80211_TX_STAT_TX_FILTERED = BIT(8), 816 IEEE80211_TX_STAT_ACK = BIT(9), 817 IEEE80211_TX_STAT_AMPDU = BIT(10), 818 IEEE80211_TX_STAT_AMPDU_NO_BACK = BIT(11), 819 IEEE80211_TX_CTL_RATE_CTRL_PROBE = BIT(12), 820 IEEE80211_TX_INTFL_OFFCHAN_TX_OK = BIT(13), 821 IEEE80211_TX_CTL_HW_80211_ENCAP = BIT(14), 822 IEEE80211_TX_INTFL_RETRIED = BIT(15), 823 IEEE80211_TX_INTFL_DONT_ENCRYPT = BIT(16), 824 IEEE80211_TX_CTL_NO_PS_BUFFER = BIT(17), 825 IEEE80211_TX_CTL_MORE_FRAMES = BIT(18), 826 IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), 827 IEEE80211_TX_INTFL_MLME_CONN_TX = BIT(20), 828 IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21), 829 IEEE80211_TX_CTL_LDPC = BIT(22), 830 IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24), 831 IEEE80211_TX_CTL_TX_OFFCHAN = BIT(25), 832 IEEE80211_TX_INTFL_TKIP_MIC_FAILURE = BIT(26), 833 IEEE80211_TX_CTL_NO_CCK_RATE = BIT(27), 834 IEEE80211_TX_STATUS_EOSP = BIT(28), 835 IEEE80211_TX_CTL_USE_MINRATE = BIT(29), 836 IEEE80211_TX_CTL_DONTFRAG = BIT(30), 837 IEEE80211_TX_STAT_NOACK_TRANSMITTED = BIT(31), 838 }; 839 840 #define IEEE80211_TX_CTL_STBC_SHIFT 23 841 842 #define IEEE80211_TX_RC_S1G_MCS IEEE80211_TX_RC_VHT_MCS 843 844 /** 845 * enum mac80211_tx_control_flags - flags to describe transmit control 846 * 847 * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control 848 * protocol frame (e.g. EAP) 849 * @IEEE80211_TX_CTRL_PS_RESPONSE: This frame is a response to a poll 850 * frame (PS-Poll or uAPSD). 851 * @IEEE80211_TX_CTRL_RATE_INJECT: This frame is injected with rate information 852 * @IEEE80211_TX_CTRL_AMSDU: This frame is an A-MSDU frame 853 * @IEEE80211_TX_CTRL_FAST_XMIT: This frame is going through the fast_xmit path 854 * @IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP: This frame skips mesh path lookup 855 * @IEEE80211_TX_INTCFL_NEED_TXPROCESSING: completely internal to mac80211, 856 * used to indicate that a pending frame requires TX processing before 857 * it can be sent out. 858 * @IEEE80211_TX_CTRL_NO_SEQNO: Do not overwrite the sequence number that 859 * has already been assigned to this frame. 860 * @IEEE80211_TX_CTRL_DONT_REORDER: This frame should not be reordered 861 * relative to other frames that have this flag set, independent 862 * of their QoS TID or other priority field values. 863 * 864 * These flags are used in tx_info->control.flags. 865 */ 866 enum mac80211_tx_control_flags { 867 IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0), 868 IEEE80211_TX_CTRL_PS_RESPONSE = BIT(1), 869 IEEE80211_TX_CTRL_RATE_INJECT = BIT(2), 870 IEEE80211_TX_CTRL_AMSDU = BIT(3), 871 IEEE80211_TX_CTRL_FAST_XMIT = BIT(4), 872 IEEE80211_TX_CTRL_SKIP_MPATH_LOOKUP = BIT(5), 873 IEEE80211_TX_INTCFL_NEED_TXPROCESSING = BIT(6), 874 IEEE80211_TX_CTRL_NO_SEQNO = BIT(7), 875 IEEE80211_TX_CTRL_DONT_REORDER = BIT(8), 876 }; 877 878 /* 879 * This definition is used as a mask to clear all temporary flags, which are 880 * set by the tx handlers for each transmission attempt by the mac80211 stack. 881 */ 882 #define IEEE80211_TX_TEMPORARY_FLAGS (IEEE80211_TX_CTL_NO_ACK | \ 883 IEEE80211_TX_CTL_CLEAR_PS_FILT | IEEE80211_TX_CTL_FIRST_FRAGMENT | \ 884 IEEE80211_TX_CTL_SEND_AFTER_DTIM | IEEE80211_TX_CTL_AMPDU | \ 885 IEEE80211_TX_STAT_TX_FILTERED | IEEE80211_TX_STAT_ACK | \ 886 IEEE80211_TX_STAT_AMPDU | IEEE80211_TX_STAT_AMPDU_NO_BACK | \ 887 IEEE80211_TX_CTL_RATE_CTRL_PROBE | IEEE80211_TX_CTL_NO_PS_BUFFER | \ 888 IEEE80211_TX_CTL_MORE_FRAMES | IEEE80211_TX_CTL_LDPC | \ 889 IEEE80211_TX_CTL_STBC | IEEE80211_TX_STATUS_EOSP) 890 891 /** 892 * enum mac80211_rate_control_flags - per-rate flags set by the 893 * Rate Control algorithm. 894 * 895 * These flags are set by the Rate control algorithm for each rate during tx, 896 * in the @flags member of struct ieee80211_tx_rate. 897 * 898 * @IEEE80211_TX_RC_USE_RTS_CTS: Use RTS/CTS exchange for this rate. 899 * @IEEE80211_TX_RC_USE_CTS_PROTECT: CTS-to-self protection is required. 900 * This is set if the current BSS requires ERP protection. 901 * @IEEE80211_TX_RC_USE_SHORT_PREAMBLE: Use short preamble. 902 * @IEEE80211_TX_RC_MCS: HT rate. 903 * @IEEE80211_TX_RC_VHT_MCS: VHT MCS rate, in this case the idx field is split 904 * into a higher 4 bits (Nss) and lower 4 bits (MCS number) 905 * @IEEE80211_TX_RC_GREEN_FIELD: Indicates whether this rate should be used in 906 * Greenfield mode. 907 * @IEEE80211_TX_RC_40_MHZ_WIDTH: Indicates if the Channel Width should be 40 MHz. 908 * @IEEE80211_TX_RC_80_MHZ_WIDTH: Indicates 80 MHz transmission 909 * @IEEE80211_TX_RC_160_MHZ_WIDTH: Indicates 160 MHz transmission 910 * (80+80 isn't supported yet) 911 * @IEEE80211_TX_RC_DUP_DATA: The frame should be transmitted on both of the 912 * adjacent 20 MHz channels, if the current channel type is 913 * NL80211_CHAN_HT40MINUS or NL80211_CHAN_HT40PLUS. 914 * @IEEE80211_TX_RC_SHORT_GI: Short Guard interval should be used for this rate. 915 */ 916 enum mac80211_rate_control_flags { 917 IEEE80211_TX_RC_USE_RTS_CTS = BIT(0), 918 IEEE80211_TX_RC_USE_CTS_PROTECT = BIT(1), 919 IEEE80211_TX_RC_USE_SHORT_PREAMBLE = BIT(2), 920 921 /* rate index is an HT/VHT MCS instead of an index */ 922 IEEE80211_TX_RC_MCS = BIT(3), 923 IEEE80211_TX_RC_GREEN_FIELD = BIT(4), 924 IEEE80211_TX_RC_40_MHZ_WIDTH = BIT(5), 925 IEEE80211_TX_RC_DUP_DATA = BIT(6), 926 IEEE80211_TX_RC_SHORT_GI = BIT(7), 927 IEEE80211_TX_RC_VHT_MCS = BIT(8), 928 IEEE80211_TX_RC_80_MHZ_WIDTH = BIT(9), 929 IEEE80211_TX_RC_160_MHZ_WIDTH = BIT(10), 930 }; 931 932 933 /* there are 40 bytes if you don't need the rateset to be kept */ 934 #define IEEE80211_TX_INFO_DRIVER_DATA_SIZE 40 935 936 /* if you do need the rateset, then you have less space */ 937 #define IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE 24 938 939 /* maximum number of rate stages */ 940 #define IEEE80211_TX_MAX_RATES 4 941 942 /* maximum number of rate table entries */ 943 #define IEEE80211_TX_RATE_TABLE_SIZE 4 944 945 /** 946 * struct ieee80211_tx_rate - rate selection/status 947 * 948 * @idx: rate index to attempt to send with 949 * @flags: rate control flags (&enum mac80211_rate_control_flags) 950 * @count: number of tries in this rate before going to the next rate 951 * 952 * A value of -1 for @idx indicates an invalid rate and, if used 953 * in an array of retry rates, that no more rates should be tried. 954 * 955 * When used for transmit status reporting, the driver should 956 * always report the rate along with the flags it used. 957 * 958 * &struct ieee80211_tx_info contains an array of these structs 959 * in the control information, and it will be filled by the rate 960 * control algorithm according to what should be sent. For example, 961 * if this array contains, in the format { <idx>, <count> } the 962 * information:: 963 * 964 * { 3, 2 }, { 2, 2 }, { 1, 4 }, { -1, 0 }, { -1, 0 } 965 * 966 * then this means that the frame should be transmitted 967 * up to twice at rate 3, up to twice at rate 2, and up to four 968 * times at rate 1 if it doesn't get acknowledged. Say it gets 969 * acknowledged by the peer after the fifth attempt, the status 970 * information should then contain:: 971 * 972 * { 3, 2 }, { 2, 2 }, { 1, 1 }, { -1, 0 } ... 973 * 974 * since it was transmitted twice at rate 3, twice at rate 2 975 * and once at rate 1 after which we received an acknowledgement. 976 */ 977 struct ieee80211_tx_rate { 978 s8 idx; 979 u16 count:5, 980 flags:11; 981 } __packed; 982 983 #define IEEE80211_MAX_TX_RETRY 31 984 985 static inline void ieee80211_rate_set_vht(struct ieee80211_tx_rate *rate, 986 u8 mcs, u8 nss) 987 { 988 WARN_ON(mcs & ~0xF); 989 WARN_ON((nss - 1) & ~0x7); 990 rate->idx = ((nss - 1) << 4) | mcs; 991 } 992 993 static inline u8 994 ieee80211_rate_get_vht_mcs(const struct ieee80211_tx_rate *rate) 995 { 996 return rate->idx & 0xF; 997 } 998 999 static inline u8 1000 ieee80211_rate_get_vht_nss(const struct ieee80211_tx_rate *rate) 1001 { 1002 return (rate->idx >> 4) + 1; 1003 } 1004 1005 /** 1006 * struct ieee80211_tx_info - skb transmit information 1007 * 1008 * This structure is placed in skb->cb for three uses: 1009 * (1) mac80211 TX control - mac80211 tells the driver what to do 1010 * (2) driver internal use (if applicable) 1011 * (3) TX status information - driver tells mac80211 what happened 1012 * 1013 * @flags: transmit info flags, defined above 1014 * @band: the band to transmit on (use for checking for races) 1015 * @hw_queue: HW queue to put the frame on, skb_get_queue_mapping() gives the AC 1016 * @ack_frame_id: internal frame ID for TX status, used internally 1017 * @tx_time_est: TX time estimate in units of 4us, used internally 1018 * @control: union part for control data 1019 * @control.rates: TX rates array to try 1020 * @control.rts_cts_rate_idx: rate for RTS or CTS 1021 * @control.use_rts: use RTS 1022 * @control.use_cts_prot: use RTS/CTS 1023 * @control.short_preamble: use short preamble (CCK only) 1024 * @control.skip_table: skip externally configured rate table 1025 * @control.jiffies: timestamp for expiry on powersave clients 1026 * @control.vif: virtual interface (may be NULL) 1027 * @control.hw_key: key to encrypt with (may be NULL) 1028 * @control.flags: control flags, see &enum mac80211_tx_control_flags 1029 * @control.enqueue_time: enqueue time (for iTXQs) 1030 * @driver_rates: alias to @control.rates to reserve space 1031 * @pad: padding 1032 * @rate_driver_data: driver use area if driver needs @control.rates 1033 * @status: union part for status data 1034 * @status.rates: attempted rates 1035 * @status.ack_signal: ACK signal 1036 * @status.ampdu_ack_len: AMPDU ack length 1037 * @status.ampdu_len: AMPDU length 1038 * @status.antenna: (legacy, kept only for iwlegacy) 1039 * @status.tx_time: airtime consumed for transmission; note this is only 1040 * used for WMM AC, not for airtime fairness 1041 * @status.is_valid_ack_signal: ACK signal is valid 1042 * @status.status_driver_data: driver use area 1043 * @ack: union part for pure ACK data 1044 * @ack.cookie: cookie for the ACK 1045 * @driver_data: array of driver_data pointers 1046 * @ampdu_ack_len: number of acked aggregated frames. 1047 * relevant only if IEEE80211_TX_STAT_AMPDU was set. 1048 * @ampdu_len: number of aggregated frames. 1049 * relevant only if IEEE80211_TX_STAT_AMPDU was set. 1050 * @ack_signal: signal strength of the ACK frame 1051 */ 1052 struct ieee80211_tx_info { 1053 /* common information */ 1054 u32 flags; 1055 u32 band:3, 1056 ack_frame_id:13, 1057 hw_queue:4, 1058 tx_time_est:10; 1059 /* 2 free bits */ 1060 1061 union { 1062 struct { 1063 union { 1064 /* rate control */ 1065 struct { 1066 struct ieee80211_tx_rate rates[ 1067 IEEE80211_TX_MAX_RATES]; 1068 s8 rts_cts_rate_idx; 1069 u8 use_rts:1; 1070 u8 use_cts_prot:1; 1071 u8 short_preamble:1; 1072 u8 skip_table:1; 1073 /* 2 bytes free */ 1074 }; 1075 /* only needed before rate control */ 1076 unsigned long jiffies; 1077 }; 1078 /* NB: vif can be NULL for injected frames */ 1079 struct ieee80211_vif *vif; 1080 struct ieee80211_key_conf *hw_key; 1081 u32 flags; 1082 codel_time_t enqueue_time; 1083 } control; 1084 struct { 1085 u64 cookie; 1086 } ack; 1087 struct { 1088 struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES]; 1089 s32 ack_signal; 1090 u8 ampdu_ack_len; 1091 u8 ampdu_len; 1092 u8 antenna; 1093 u16 tx_time; 1094 bool is_valid_ack_signal; 1095 void *status_driver_data[19 / sizeof(void *)]; 1096 } status; 1097 struct { 1098 struct ieee80211_tx_rate driver_rates[ 1099 IEEE80211_TX_MAX_RATES]; 1100 u8 pad[4]; 1101 1102 void *rate_driver_data[ 1103 IEEE80211_TX_INFO_RATE_DRIVER_DATA_SIZE / sizeof(void *)]; 1104 }; 1105 void *driver_data[ 1106 IEEE80211_TX_INFO_DRIVER_DATA_SIZE / sizeof(void *)]; 1107 }; 1108 }; 1109 1110 static inline u16 1111 ieee80211_info_set_tx_time_est(struct ieee80211_tx_info *info, u16 tx_time_est) 1112 { 1113 /* We only have 10 bits in tx_time_est, so store airtime 1114 * in increments of 4us and clamp the maximum to 2**12-1 1115 */ 1116 info->tx_time_est = min_t(u16, tx_time_est, 4095) >> 2; 1117 return info->tx_time_est << 2; 1118 } 1119 1120 static inline u16 1121 ieee80211_info_get_tx_time_est(struct ieee80211_tx_info *info) 1122 { 1123 return info->tx_time_est << 2; 1124 } 1125 1126 /** 1127 * struct ieee80211_tx_status - extended tx status info for rate control 1128 * 1129 * @sta: Station that the packet was transmitted for 1130 * @info: Basic tx status information 1131 * @skb: Packet skb (can be NULL if not provided by the driver) 1132 * @rate: The TX rate that was used when sending the packet 1133 * @free_list: list where processed skbs are stored to be free'd by the driver 1134 */ 1135 struct ieee80211_tx_status { 1136 struct ieee80211_sta *sta; 1137 struct ieee80211_tx_info *info; 1138 struct sk_buff *skb; 1139 struct rate_info *rate; 1140 struct list_head *free_list; 1141 }; 1142 1143 /** 1144 * struct ieee80211_scan_ies - descriptors for different blocks of IEs 1145 * 1146 * This structure is used to point to different blocks of IEs in HW scan 1147 * and scheduled scan. These blocks contain the IEs passed by userspace 1148 * and the ones generated by mac80211. 1149 * 1150 * @ies: pointers to band specific IEs. 1151 * @len: lengths of band_specific IEs. 1152 * @common_ies: IEs for all bands (especially vendor specific ones) 1153 * @common_ie_len: length of the common_ies 1154 */ 1155 struct ieee80211_scan_ies { 1156 const u8 *ies[NUM_NL80211_BANDS]; 1157 size_t len[NUM_NL80211_BANDS]; 1158 const u8 *common_ies; 1159 size_t common_ie_len; 1160 }; 1161 1162 1163 static inline struct ieee80211_tx_info *IEEE80211_SKB_CB(struct sk_buff *skb) 1164 { 1165 return (struct ieee80211_tx_info *)skb->cb; 1166 } 1167 1168 static inline struct ieee80211_rx_status *IEEE80211_SKB_RXCB(struct sk_buff *skb) 1169 { 1170 return (struct ieee80211_rx_status *)skb->cb; 1171 } 1172 1173 /** 1174 * ieee80211_tx_info_clear_status - clear TX status 1175 * 1176 * @info: The &struct ieee80211_tx_info to be cleared. 1177 * 1178 * When the driver passes an skb back to mac80211, it must report 1179 * a number of things in TX status. This function clears everything 1180 * in the TX status but the rate control information (it does clear 1181 * the count since you need to fill that in anyway). 1182 * 1183 * NOTE: You can only use this function if you do NOT use 1184 * info->driver_data! Use info->rate_driver_data 1185 * instead if you need only the less space that allows. 1186 */ 1187 static inline void 1188 ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info) 1189 { 1190 int i; 1191 1192 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 1193 offsetof(struct ieee80211_tx_info, control.rates)); 1194 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 1195 offsetof(struct ieee80211_tx_info, driver_rates)); 1196 BUILD_BUG_ON(offsetof(struct ieee80211_tx_info, status.rates) != 8); 1197 /* clear the rate counts */ 1198 for (i = 0; i < IEEE80211_TX_MAX_RATES; i++) 1199 info->status.rates[i].count = 0; 1200 1201 BUILD_BUG_ON( 1202 offsetof(struct ieee80211_tx_info, status.ack_signal) != 20); 1203 memset(&info->status.ampdu_ack_len, 0, 1204 sizeof(struct ieee80211_tx_info) - 1205 offsetof(struct ieee80211_tx_info, status.ampdu_ack_len)); 1206 } 1207 1208 1209 /** 1210 * enum mac80211_rx_flags - receive flags 1211 * 1212 * These flags are used with the @flag member of &struct ieee80211_rx_status. 1213 * @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame. 1214 * Use together with %RX_FLAG_MMIC_STRIPPED. 1215 * @RX_FLAG_DECRYPTED: This frame was decrypted in hardware. 1216 * @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame, 1217 * verification has been done by the hardware. 1218 * @RX_FLAG_IV_STRIPPED: The IV and ICV are stripped from this frame. 1219 * If this flag is set, the stack cannot do any replay detection 1220 * hence the driver or hardware will have to do that. 1221 * @RX_FLAG_PN_VALIDATED: Currently only valid for CCMP/GCMP frames, this 1222 * flag indicates that the PN was verified for replay protection. 1223 * Note that this flag is also currently only supported when a frame 1224 * is also decrypted (ie. @RX_FLAG_DECRYPTED must be set) 1225 * @RX_FLAG_DUP_VALIDATED: The driver should set this flag if it did 1226 * de-duplication by itself. 1227 * @RX_FLAG_FAILED_FCS_CRC: Set this flag if the FCS check failed on 1228 * the frame. 1229 * @RX_FLAG_FAILED_PLCP_CRC: Set this flag if the PCLP check failed on 1230 * the frame. 1231 * @RX_FLAG_MACTIME_START: The timestamp passed in the RX status (@mactime 1232 * field) is valid and contains the time the first symbol of the MPDU 1233 * was received. This is useful in monitor mode and for proper IBSS 1234 * merging. 1235 * @RX_FLAG_MACTIME_END: The timestamp passed in the RX status (@mactime 1236 * field) is valid and contains the time the last symbol of the MPDU 1237 * (including FCS) was received. 1238 * @RX_FLAG_MACTIME_PLCP_START: The timestamp passed in the RX status (@mactime 1239 * field) is valid and contains the time the SYNC preamble was received. 1240 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present. 1241 * Valid only for data frames (mainly A-MPDU) 1242 * @RX_FLAG_AMPDU_DETAILS: A-MPDU details are known, in particular the reference 1243 * number (@ampdu_reference) must be populated and be a distinct number for 1244 * each A-MPDU 1245 * @RX_FLAG_AMPDU_LAST_KNOWN: last subframe is known, should be set on all 1246 * subframes of a single A-MPDU 1247 * @RX_FLAG_AMPDU_IS_LAST: this subframe is the last subframe of the A-MPDU 1248 * @RX_FLAG_AMPDU_DELIM_CRC_ERROR: A delimiter CRC error has been detected 1249 * on this subframe 1250 * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC 1251 * is stored in the @ampdu_delimiter_crc field) 1252 * @RX_FLAG_MIC_STRIPPED: The mic was stripped of this packet. Decryption was 1253 * done by the hardware 1254 * @RX_FLAG_ONLY_MONITOR: Report frame only to monitor interfaces without 1255 * processing it in any regular way. 1256 * This is useful if drivers offload some frames but still want to report 1257 * them for sniffing purposes. 1258 * @RX_FLAG_SKIP_MONITOR: Process and report frame to all interfaces except 1259 * monitor interfaces. 1260 * This is useful if drivers offload some frames but still want to report 1261 * them for sniffing purposes. 1262 * @RX_FLAG_AMSDU_MORE: Some drivers may prefer to report separate A-MSDU 1263 * subframes instead of a one huge frame for performance reasons. 1264 * All, but the last MSDU from an A-MSDU should have this flag set. E.g. 1265 * if an A-MSDU has 3 frames, the first 2 must have the flag set, while 1266 * the 3rd (last) one must not have this flag set. The flag is used to 1267 * deal with retransmission/duplication recovery properly since A-MSDU 1268 * subframes share the same sequence number. Reported subframes can be 1269 * either regular MSDU or singly A-MSDUs. Subframes must not be 1270 * interleaved with other frames. 1271 * @RX_FLAG_RADIOTAP_VENDOR_DATA: This frame contains vendor-specific 1272 * radiotap data in the skb->data (before the frame) as described by 1273 * the &struct ieee80211_vendor_radiotap. 1274 * @RX_FLAG_ALLOW_SAME_PN: Allow the same PN as same packet before. 1275 * This is used for AMSDU subframes which can have the same PN as 1276 * the first subframe. 1277 * @RX_FLAG_ICV_STRIPPED: The ICV is stripped from this frame. CRC checking must 1278 * be done in the hardware. 1279 * @RX_FLAG_AMPDU_EOF_BIT: Value of the EOF bit in the A-MPDU delimiter for this 1280 * frame 1281 * @RX_FLAG_AMPDU_EOF_BIT_KNOWN: The EOF value is known 1282 * @RX_FLAG_RADIOTAP_HE: HE radiotap data is present 1283 * (&struct ieee80211_radiotap_he, mac80211 will fill in 1284 * 1285 * - DATA3_DATA_MCS 1286 * - DATA3_DATA_DCM 1287 * - DATA3_CODING 1288 * - DATA5_GI 1289 * - DATA5_DATA_BW_RU_ALLOC 1290 * - DATA6_NSTS 1291 * - DATA3_STBC 1292 * 1293 * from the RX info data, so leave those zeroed when building this data) 1294 * @RX_FLAG_RADIOTAP_HE_MU: HE MU radiotap data is present 1295 * (&struct ieee80211_radiotap_he_mu) 1296 * @RX_FLAG_RADIOTAP_LSIG: L-SIG radiotap data is present 1297 * @RX_FLAG_NO_PSDU: use the frame only for radiotap reporting, with 1298 * the "0-length PSDU" field included there. The value for it is 1299 * in &struct ieee80211_rx_status. Note that if this value isn't 1300 * known the frame shouldn't be reported. 1301 * @RX_FLAG_8023: the frame has an 802.3 header (decap offload performed by 1302 * hardware or driver) 1303 */ 1304 enum mac80211_rx_flags { 1305 RX_FLAG_MMIC_ERROR = BIT(0), 1306 RX_FLAG_DECRYPTED = BIT(1), 1307 RX_FLAG_MACTIME_PLCP_START = BIT(2), 1308 RX_FLAG_MMIC_STRIPPED = BIT(3), 1309 RX_FLAG_IV_STRIPPED = BIT(4), 1310 RX_FLAG_FAILED_FCS_CRC = BIT(5), 1311 RX_FLAG_FAILED_PLCP_CRC = BIT(6), 1312 RX_FLAG_MACTIME_START = BIT(7), 1313 RX_FLAG_NO_SIGNAL_VAL = BIT(8), 1314 RX_FLAG_AMPDU_DETAILS = BIT(9), 1315 RX_FLAG_PN_VALIDATED = BIT(10), 1316 RX_FLAG_DUP_VALIDATED = BIT(11), 1317 RX_FLAG_AMPDU_LAST_KNOWN = BIT(12), 1318 RX_FLAG_AMPDU_IS_LAST = BIT(13), 1319 RX_FLAG_AMPDU_DELIM_CRC_ERROR = BIT(14), 1320 RX_FLAG_AMPDU_DELIM_CRC_KNOWN = BIT(15), 1321 RX_FLAG_MACTIME_END = BIT(16), 1322 RX_FLAG_ONLY_MONITOR = BIT(17), 1323 RX_FLAG_SKIP_MONITOR = BIT(18), 1324 RX_FLAG_AMSDU_MORE = BIT(19), 1325 RX_FLAG_RADIOTAP_VENDOR_DATA = BIT(20), 1326 RX_FLAG_MIC_STRIPPED = BIT(21), 1327 RX_FLAG_ALLOW_SAME_PN = BIT(22), 1328 RX_FLAG_ICV_STRIPPED = BIT(23), 1329 RX_FLAG_AMPDU_EOF_BIT = BIT(24), 1330 RX_FLAG_AMPDU_EOF_BIT_KNOWN = BIT(25), 1331 RX_FLAG_RADIOTAP_HE = BIT(26), 1332 RX_FLAG_RADIOTAP_HE_MU = BIT(27), 1333 RX_FLAG_RADIOTAP_LSIG = BIT(28), 1334 RX_FLAG_NO_PSDU = BIT(29), 1335 RX_FLAG_8023 = BIT(30), 1336 }; 1337 1338 /** 1339 * enum mac80211_rx_encoding_flags - MCS & bandwidth flags 1340 * 1341 * @RX_ENC_FLAG_SHORTPRE: Short preamble was used for this frame 1342 * @RX_ENC_FLAG_SHORT_GI: Short guard interval was used 1343 * @RX_ENC_FLAG_HT_GF: This frame was received in a HT-greenfield transmission, 1344 * if the driver fills this value it should add 1345 * %IEEE80211_RADIOTAP_MCS_HAVE_FMT 1346 * to @hw.radiotap_mcs_details to advertise that fact. 1347 * @RX_ENC_FLAG_LDPC: LDPC was used 1348 * @RX_ENC_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3 1349 * @RX_ENC_FLAG_BF: packet was beamformed 1350 */ 1351 enum mac80211_rx_encoding_flags { 1352 RX_ENC_FLAG_SHORTPRE = BIT(0), 1353 RX_ENC_FLAG_SHORT_GI = BIT(2), 1354 RX_ENC_FLAG_HT_GF = BIT(3), 1355 RX_ENC_FLAG_STBC_MASK = BIT(4) | BIT(5), 1356 RX_ENC_FLAG_LDPC = BIT(6), 1357 RX_ENC_FLAG_BF = BIT(7), 1358 }; 1359 1360 #define RX_ENC_FLAG_STBC_SHIFT 4 1361 1362 enum mac80211_rx_encoding { 1363 RX_ENC_LEGACY = 0, 1364 RX_ENC_HT, 1365 RX_ENC_VHT, 1366 RX_ENC_HE, 1367 }; 1368 1369 /** 1370 * struct ieee80211_rx_status - receive status 1371 * 1372 * The low-level driver should provide this information (the subset 1373 * supported by hardware) to the 802.11 code with each received 1374 * frame, in the skb's control buffer (cb). 1375 * 1376 * @mactime: value in microseconds of the 64-bit Time Synchronization Function 1377 * (TSF) timer when the first data symbol (MPDU) arrived at the hardware. 1378 * @boottime_ns: CLOCK_BOOTTIME timestamp the frame was received at, this is 1379 * needed only for beacons and probe responses that update the scan cache. 1380 * @device_timestamp: arbitrary timestamp for the device, mac80211 doesn't use 1381 * it but can store it and pass it back to the driver for synchronisation 1382 * @band: the active band when this frame was received 1383 * @freq: frequency the radio was tuned to when receiving this frame, in MHz 1384 * This field must be set for management frames, but isn't strictly needed 1385 * for data (other) frames - for those it only affects radiotap reporting. 1386 * @freq_offset: @freq has a positive offset of 500Khz. 1387 * @signal: signal strength when receiving this frame, either in dBm, in dB or 1388 * unspecified depending on the hardware capabilities flags 1389 * @IEEE80211_HW_SIGNAL_* 1390 * @chains: bitmask of receive chains for which separate signal strength 1391 * values were filled. 1392 * @chain_signal: per-chain signal strength, in dBm (unlike @signal, doesn't 1393 * support dB or unspecified units) 1394 * @antenna: antenna used 1395 * @rate_idx: index of data rate into band's supported rates or MCS index if 1396 * HT or VHT is used (%RX_FLAG_HT/%RX_FLAG_VHT) 1397 * @nss: number of streams (VHT and HE only) 1398 * @flag: %RX_FLAG_\* 1399 * @encoding: &enum mac80211_rx_encoding 1400 * @bw: &enum rate_info_bw 1401 * @enc_flags: uses bits from &enum mac80211_rx_encoding_flags 1402 * @he_ru: HE RU, from &enum nl80211_he_ru_alloc 1403 * @he_gi: HE GI, from &enum nl80211_he_gi 1404 * @he_dcm: HE DCM value 1405 * @rx_flags: internal RX flags for mac80211 1406 * @ampdu_reference: A-MPDU reference number, must be a different value for 1407 * each A-MPDU but the same for each subframe within one A-MPDU 1408 * @ampdu_delimiter_crc: A-MPDU delimiter CRC 1409 * @zero_length_psdu_type: radiotap type of the 0-length PSDU 1410 */ 1411 struct ieee80211_rx_status { 1412 u64 mactime; 1413 u64 boottime_ns; 1414 u32 device_timestamp; 1415 u32 ampdu_reference; 1416 u32 flag; 1417 u16 freq: 13, freq_offset: 1; 1418 u8 enc_flags; 1419 u8 encoding:2, bw:3, he_ru:3; 1420 u8 he_gi:2, he_dcm:1; 1421 u8 rate_idx; 1422 u8 nss; 1423 u8 rx_flags; 1424 u8 band; 1425 u8 antenna; 1426 s8 signal; 1427 u8 chains; 1428 s8 chain_signal[IEEE80211_MAX_CHAINS]; 1429 u8 ampdu_delimiter_crc; 1430 u8 zero_length_psdu_type; 1431 }; 1432 1433 static inline u32 1434 ieee80211_rx_status_to_khz(struct ieee80211_rx_status *rx_status) 1435 { 1436 return MHZ_TO_KHZ(rx_status->freq) + 1437 (rx_status->freq_offset ? 500 : 0); 1438 } 1439 1440 /** 1441 * struct ieee80211_vendor_radiotap - vendor radiotap data information 1442 * @present: presence bitmap for this vendor namespace 1443 * (this could be extended in the future if any vendor needs more 1444 * bits, the radiotap spec does allow for that) 1445 * @align: radiotap vendor namespace alignment. This defines the needed 1446 * alignment for the @data field below, not for the vendor namespace 1447 * description itself (which has a fixed 2-byte alignment) 1448 * Must be a power of two, and be set to at least 1! 1449 * @oui: radiotap vendor namespace OUI 1450 * @subns: radiotap vendor sub namespace 1451 * @len: radiotap vendor sub namespace skip length, if alignment is done 1452 * then that's added to this, i.e. this is only the length of the 1453 * @data field. 1454 * @pad: number of bytes of padding after the @data, this exists so that 1455 * the skb data alignment can be preserved even if the data has odd 1456 * length 1457 * @data: the actual vendor namespace data 1458 * 1459 * This struct, including the vendor data, goes into the skb->data before 1460 * the 802.11 header. It's split up in mac80211 using the align/oui/subns 1461 * data. 1462 */ 1463 struct ieee80211_vendor_radiotap { 1464 u32 present; 1465 u8 align; 1466 u8 oui[3]; 1467 u8 subns; 1468 u8 pad; 1469 u16 len; 1470 u8 data[]; 1471 } __packed; 1472 1473 /** 1474 * enum ieee80211_conf_flags - configuration flags 1475 * 1476 * Flags to define PHY configuration options 1477 * 1478 * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this 1479 * to determine for example whether to calculate timestamps for packets 1480 * or not, do not use instead of filter flags! 1481 * @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only). 1482 * This is the power save mode defined by IEEE 802.11-2007 section 11.2, 1483 * meaning that the hardware still wakes up for beacons, is able to 1484 * transmit frames and receive the possible acknowledgment frames. 1485 * Not to be confused with hardware specific wakeup/sleep states, 1486 * driver is responsible for that. See the section "Powersave support" 1487 * for more. 1488 * @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set 1489 * the driver should be prepared to handle configuration requests but 1490 * may turn the device off as much as possible. Typically, this flag will 1491 * be set when an interface is set UP but not associated or scanning, but 1492 * it can also be unset in that case when monitor interfaces are active. 1493 * @IEEE80211_CONF_OFFCHANNEL: The device is currently not on its main 1494 * operating channel. 1495 */ 1496 enum ieee80211_conf_flags { 1497 IEEE80211_CONF_MONITOR = (1<<0), 1498 IEEE80211_CONF_PS = (1<<1), 1499 IEEE80211_CONF_IDLE = (1<<2), 1500 IEEE80211_CONF_OFFCHANNEL = (1<<3), 1501 }; 1502 1503 1504 /** 1505 * enum ieee80211_conf_changed - denotes which configuration changed 1506 * 1507 * @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed 1508 * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed 1509 * @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed 1510 * @IEEE80211_CONF_CHANGE_POWER: the TX power changed 1511 * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed 1512 * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed 1513 * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed 1514 * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed 1515 * Note that this is only valid if channel contexts are not used, 1516 * otherwise each channel context has the number of chains listed. 1517 */ 1518 enum ieee80211_conf_changed { 1519 IEEE80211_CONF_CHANGE_SMPS = BIT(1), 1520 IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2), 1521 IEEE80211_CONF_CHANGE_MONITOR = BIT(3), 1522 IEEE80211_CONF_CHANGE_PS = BIT(4), 1523 IEEE80211_CONF_CHANGE_POWER = BIT(5), 1524 IEEE80211_CONF_CHANGE_CHANNEL = BIT(6), 1525 IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7), 1526 IEEE80211_CONF_CHANGE_IDLE = BIT(8), 1527 }; 1528 1529 /** 1530 * enum ieee80211_smps_mode - spatial multiplexing power save mode 1531 * 1532 * @IEEE80211_SMPS_AUTOMATIC: automatic 1533 * @IEEE80211_SMPS_OFF: off 1534 * @IEEE80211_SMPS_STATIC: static 1535 * @IEEE80211_SMPS_DYNAMIC: dynamic 1536 * @IEEE80211_SMPS_NUM_MODES: internal, don't use 1537 */ 1538 enum ieee80211_smps_mode { 1539 IEEE80211_SMPS_AUTOMATIC, 1540 IEEE80211_SMPS_OFF, 1541 IEEE80211_SMPS_STATIC, 1542 IEEE80211_SMPS_DYNAMIC, 1543 1544 /* keep last */ 1545 IEEE80211_SMPS_NUM_MODES, 1546 }; 1547 1548 /** 1549 * struct ieee80211_conf - configuration of the device 1550 * 1551 * This struct indicates how the driver shall configure the hardware. 1552 * 1553 * @flags: configuration flags defined above 1554 * 1555 * @listen_interval: listen interval in units of beacon interval 1556 * @ps_dtim_period: The DTIM period of the AP we're connected to, for use 1557 * in power saving. Power saving will not be enabled until a beacon 1558 * has been received and the DTIM period is known. 1559 * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the 1560 * powersave documentation below. This variable is valid only when 1561 * the CONF_PS flag is set. 1562 * 1563 * @power_level: requested transmit power (in dBm), backward compatibility 1564 * value only that is set to the minimum of all interfaces 1565 * 1566 * @chandef: the channel definition to tune to 1567 * @radar_enabled: whether radar detection is enabled 1568 * 1569 * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame 1570 * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11, 1571 * but actually means the number of transmissions not the number of retries 1572 * @short_frame_max_tx_count: Maximum number of transmissions for a "short" 1573 * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the 1574 * number of transmissions not the number of retries 1575 * 1576 * @smps_mode: spatial multiplexing powersave mode; note that 1577 * %IEEE80211_SMPS_STATIC is used when the device is not 1578 * configured for an HT channel. 1579 * Note that this is only valid if channel contexts are not used, 1580 * otherwise each channel context has the number of chains listed. 1581 */ 1582 struct ieee80211_conf { 1583 u32 flags; 1584 int power_level, dynamic_ps_timeout; 1585 1586 u16 listen_interval; 1587 u8 ps_dtim_period; 1588 1589 u8 long_frame_max_tx_count, short_frame_max_tx_count; 1590 1591 struct cfg80211_chan_def chandef; 1592 bool radar_enabled; 1593 enum ieee80211_smps_mode smps_mode; 1594 }; 1595 1596 /** 1597 * struct ieee80211_channel_switch - holds the channel switch data 1598 * 1599 * The information provided in this structure is required for channel switch 1600 * operation. 1601 * 1602 * @timestamp: value in microseconds of the 64-bit Time Synchronization 1603 * Function (TSF) timer when the frame containing the channel switch 1604 * announcement was received. This is simply the rx.mactime parameter 1605 * the driver passed into mac80211. 1606 * @device_timestamp: arbitrary timestamp for the device, this is the 1607 * rx.device_timestamp parameter the driver passed to mac80211. 1608 * @block_tx: Indicates whether transmission must be blocked before the 1609 * scheduled channel switch, as indicated by the AP. 1610 * @chandef: the new channel to switch to 1611 * @count: the number of TBTT's until the channel switch event 1612 * @delay: maximum delay between the time the AP transmitted the last beacon in 1613 * current channel and the expected time of the first beacon in the new 1614 * channel, expressed in TU. 1615 */ 1616 struct ieee80211_channel_switch { 1617 u64 timestamp; 1618 u32 device_timestamp; 1619 bool block_tx; 1620 struct cfg80211_chan_def chandef; 1621 u8 count; 1622 u32 delay; 1623 }; 1624 1625 /** 1626 * enum ieee80211_vif_flags - virtual interface flags 1627 * 1628 * @IEEE80211_VIF_BEACON_FILTER: the device performs beacon filtering 1629 * on this virtual interface to avoid unnecessary CPU wakeups 1630 * @IEEE80211_VIF_SUPPORTS_CQM_RSSI: the device can do connection quality 1631 * monitoring on this virtual interface -- i.e. it can monitor 1632 * connection quality related parameters, such as the RSSI level and 1633 * provide notifications if configured trigger levels are reached. 1634 * @IEEE80211_VIF_SUPPORTS_UAPSD: The device can do U-APSD for this 1635 * interface. This flag should be set during interface addition, 1636 * but may be set/cleared as late as authentication to an AP. It is 1637 * only valid for managed/station mode interfaces. 1638 * @IEEE80211_VIF_GET_NOA_UPDATE: request to handle NOA attributes 1639 * and send P2P_PS notification to the driver if NOA changed, even 1640 * this is not pure P2P vif. 1641 */ 1642 enum ieee80211_vif_flags { 1643 IEEE80211_VIF_BEACON_FILTER = BIT(0), 1644 IEEE80211_VIF_SUPPORTS_CQM_RSSI = BIT(1), 1645 IEEE80211_VIF_SUPPORTS_UAPSD = BIT(2), 1646 IEEE80211_VIF_GET_NOA_UPDATE = BIT(3), 1647 }; 1648 1649 1650 /** 1651 * enum ieee80211_offload_flags - virtual interface offload flags 1652 * 1653 * @IEEE80211_OFFLOAD_ENCAP_ENABLED: tx encapsulation offload is enabled 1654 * The driver supports sending frames passed as 802.3 frames by mac80211. 1655 * It must also support sending 802.11 packets for the same interface. 1656 * @IEEE80211_OFFLOAD_ENCAP_4ADDR: support 4-address mode encapsulation offload 1657 * @IEEE80211_OFFLOAD_DECAP_ENABLED: rx encapsulation offload is enabled 1658 * The driver supports passing received 802.11 frames as 802.3 frames to 1659 * mac80211. 1660 */ 1661 1662 enum ieee80211_offload_flags { 1663 IEEE80211_OFFLOAD_ENCAP_ENABLED = BIT(0), 1664 IEEE80211_OFFLOAD_ENCAP_4ADDR = BIT(1), 1665 IEEE80211_OFFLOAD_DECAP_ENABLED = BIT(2), 1666 }; 1667 1668 /** 1669 * struct ieee80211_vif - per-interface data 1670 * 1671 * Data in this structure is continually present for driver 1672 * use during the life of a virtual interface. 1673 * 1674 * @type: type of this virtual interface 1675 * @bss_conf: BSS configuration for this interface, either our own 1676 * or the BSS we're associated to 1677 * @addr: address of this interface 1678 * @p2p: indicates whether this AP or STA interface is a p2p 1679 * interface, i.e. a GO or p2p-sta respectively 1680 * @csa_active: marks whether a channel switch is going on. Internally it is 1681 * write-protected by sdata_lock and local->mtx so holding either is fine 1682 * for read access. 1683 * @mu_mimo_owner: indicates interface owns MU-MIMO capability 1684 * @driver_flags: flags/capabilities the driver has for this interface, 1685 * these need to be set (or cleared) when the interface is added 1686 * or, if supported by the driver, the interface type is changed 1687 * at runtime, mac80211 will never touch this field 1688 * @offloaad_flags: hardware offload capabilities/flags for this interface. 1689 * These are initialized by mac80211 before calling .add_interface, 1690 * .change_interface or .update_vif_offload and updated by the driver 1691 * within these ops, based on supported features or runtime change 1692 * restrictions. 1693 * @hw_queue: hardware queue for each AC 1694 * @cab_queue: content-after-beacon (DTIM beacon really) queue, AP mode only 1695 * @chanctx_conf: The channel context this interface is assigned to, or %NULL 1696 * when it is not assigned. This pointer is RCU-protected due to the TX 1697 * path needing to access it; even though the netdev carrier will always 1698 * be off when it is %NULL there can still be races and packets could be 1699 * processed after it switches back to %NULL. 1700 * @debugfs_dir: debugfs dentry, can be used by drivers to create own per 1701 * interface debug files. Note that it will be NULL for the virtual 1702 * monitor interface (if that is requested.) 1703 * @probe_req_reg: probe requests should be reported to mac80211 for this 1704 * interface. 1705 * @rx_mcast_action_reg: multicast Action frames should be reported to mac80211 1706 * for this interface. 1707 * @drv_priv: data area for driver use, will always be aligned to 1708 * sizeof(void \*). 1709 * @txq: the multicast data TX queue (if driver uses the TXQ abstraction) 1710 * @txqs_stopped: per AC flag to indicate that intermediate TXQs are stopped, 1711 * protected by fq->lock. 1712 * @offload_flags: 802.3 -> 802.11 enapsulation offload flags, see 1713 * &enum ieee80211_offload_flags. 1714 * @color_change_active: marks whether a color change is ongoing. Internally it is 1715 * write-protected by sdata_lock and local->mtx so holding either is fine 1716 * for read access. 1717 * @color_change_color: the bss color that will be used after the change. 1718 */ 1719 struct ieee80211_vif { 1720 enum nl80211_iftype type; 1721 struct ieee80211_bss_conf bss_conf; 1722 u8 addr[ETH_ALEN] __aligned(2); 1723 bool p2p; 1724 bool csa_active; 1725 bool mu_mimo_owner; 1726 1727 u8 cab_queue; 1728 u8 hw_queue[IEEE80211_NUM_ACS]; 1729 1730 struct ieee80211_txq *txq; 1731 1732 struct ieee80211_chanctx_conf __rcu *chanctx_conf; 1733 1734 u32 driver_flags; 1735 u32 offload_flags; 1736 1737 #ifdef CONFIG_MAC80211_DEBUGFS 1738 struct dentry *debugfs_dir; 1739 #endif 1740 1741 bool probe_req_reg; 1742 bool rx_mcast_action_reg; 1743 1744 bool txqs_stopped[IEEE80211_NUM_ACS]; 1745 1746 bool color_change_active; 1747 u8 color_change_color; 1748 1749 /* must be last */ 1750 u8 drv_priv[] __aligned(sizeof(void *)); 1751 }; 1752 1753 static inline bool ieee80211_vif_is_mesh(struct ieee80211_vif *vif) 1754 { 1755 #ifdef CONFIG_MAC80211_MESH 1756 return vif->type == NL80211_IFTYPE_MESH_POINT; 1757 #endif 1758 return false; 1759 } 1760 1761 /** 1762 * wdev_to_ieee80211_vif - return a vif struct from a wdev 1763 * @wdev: the wdev to get the vif for 1764 * 1765 * This can be used by mac80211 drivers with direct cfg80211 APIs 1766 * (like the vendor commands) that get a wdev. 1767 * 1768 * Note that this function may return %NULL if the given wdev isn't 1769 * associated with a vif that the driver knows about (e.g. monitor 1770 * or AP_VLAN interfaces.) 1771 */ 1772 struct ieee80211_vif *wdev_to_ieee80211_vif(struct wireless_dev *wdev); 1773 1774 /** 1775 * ieee80211_vif_to_wdev - return a wdev struct from a vif 1776 * @vif: the vif to get the wdev for 1777 * 1778 * This can be used by mac80211 drivers with direct cfg80211 APIs 1779 * (like the vendor commands) that needs to get the wdev for a vif. 1780 * This can also be useful to get the netdev associated to a vif. 1781 */ 1782 struct wireless_dev *ieee80211_vif_to_wdev(struct ieee80211_vif *vif); 1783 1784 /** 1785 * enum ieee80211_key_flags - key flags 1786 * 1787 * These flags are used for communication about keys between the driver 1788 * and mac80211, with the @flags parameter of &struct ieee80211_key_conf. 1789 * 1790 * @IEEE80211_KEY_FLAG_GENERATE_IV: This flag should be set by the 1791 * driver to indicate that it requires IV generation for this 1792 * particular key. Setting this flag does not necessarily mean that SKBs 1793 * will have sufficient tailroom for ICV or MIC. 1794 * @IEEE80211_KEY_FLAG_GENERATE_MMIC: This flag should be set by 1795 * the driver for a TKIP key if it requires Michael MIC 1796 * generation in software. 1797 * @IEEE80211_KEY_FLAG_PAIRWISE: Set by mac80211, this flag indicates 1798 * that the key is pairwise rather then a shared key. 1799 * @IEEE80211_KEY_FLAG_SW_MGMT_TX: This flag should be set by the driver for a 1800 * CCMP/GCMP key if it requires CCMP/GCMP encryption of management frames 1801 * (MFP) to be done in software. 1802 * @IEEE80211_KEY_FLAG_PUT_IV_SPACE: This flag should be set by the driver 1803 * if space should be prepared for the IV, but the IV 1804 * itself should not be generated. Do not set together with 1805 * @IEEE80211_KEY_FLAG_GENERATE_IV on the same key. Setting this flag does 1806 * not necessarily mean that SKBs will have sufficient tailroom for ICV or 1807 * MIC. 1808 * @IEEE80211_KEY_FLAG_RX_MGMT: This key will be used to decrypt received 1809 * management frames. The flag can help drivers that have a hardware 1810 * crypto implementation that doesn't deal with management frames 1811 * properly by allowing them to not upload the keys to hardware and 1812 * fall back to software crypto. Note that this flag deals only with 1813 * RX, if your crypto engine can't deal with TX you can also set the 1814 * %IEEE80211_KEY_FLAG_SW_MGMT_TX flag to encrypt such frames in SW. 1815 * @IEEE80211_KEY_FLAG_GENERATE_IV_MGMT: This flag should be set by the 1816 * driver for a CCMP/GCMP key to indicate that is requires IV generation 1817 * only for management frames (MFP). 1818 * @IEEE80211_KEY_FLAG_RESERVE_TAILROOM: This flag should be set by the 1819 * driver for a key to indicate that sufficient tailroom must always 1820 * be reserved for ICV or MIC, even when HW encryption is enabled. 1821 * @IEEE80211_KEY_FLAG_PUT_MIC_SPACE: This flag should be set by the driver for 1822 * a TKIP key if it only requires MIC space. Do not set together with 1823 * @IEEE80211_KEY_FLAG_GENERATE_MMIC on the same key. 1824 * @IEEE80211_KEY_FLAG_NO_AUTO_TX: Key needs explicit Tx activation. 1825 * @IEEE80211_KEY_FLAG_GENERATE_MMIE: This flag should be set by the driver 1826 * for a AES_CMAC key to indicate that it requires sequence number 1827 * generation only 1828 */ 1829 enum ieee80211_key_flags { 1830 IEEE80211_KEY_FLAG_GENERATE_IV_MGMT = BIT(0), 1831 IEEE80211_KEY_FLAG_GENERATE_IV = BIT(1), 1832 IEEE80211_KEY_FLAG_GENERATE_MMIC = BIT(2), 1833 IEEE80211_KEY_FLAG_PAIRWISE = BIT(3), 1834 IEEE80211_KEY_FLAG_SW_MGMT_TX = BIT(4), 1835 IEEE80211_KEY_FLAG_PUT_IV_SPACE = BIT(5), 1836 IEEE80211_KEY_FLAG_RX_MGMT = BIT(6), 1837 IEEE80211_KEY_FLAG_RESERVE_TAILROOM = BIT(7), 1838 IEEE80211_KEY_FLAG_PUT_MIC_SPACE = BIT(8), 1839 IEEE80211_KEY_FLAG_NO_AUTO_TX = BIT(9), 1840 IEEE80211_KEY_FLAG_GENERATE_MMIE = BIT(10), 1841 }; 1842 1843 /** 1844 * struct ieee80211_key_conf - key information 1845 * 1846 * This key information is given by mac80211 to the driver by 1847 * the set_key() callback in &struct ieee80211_ops. 1848 * 1849 * @hw_key_idx: To be set by the driver, this is the key index the driver 1850 * wants to be given when a frame is transmitted and needs to be 1851 * encrypted in hardware. 1852 * @cipher: The key's cipher suite selector. 1853 * @tx_pn: PN used for TX keys, may be used by the driver as well if it 1854 * needs to do software PN assignment by itself (e.g. due to TSO) 1855 * @flags: key flags, see &enum ieee80211_key_flags. 1856 * @keyidx: the key index (0-3) 1857 * @keylen: key material length 1858 * @key: key material. For ALG_TKIP the key is encoded as a 256-bit (32 byte) 1859 * data block: 1860 * - Temporal Encryption Key (128 bits) 1861 * - Temporal Authenticator Tx MIC Key (64 bits) 1862 * - Temporal Authenticator Rx MIC Key (64 bits) 1863 * @icv_len: The ICV length for this key type 1864 * @iv_len: The IV length for this key type 1865 */ 1866 struct ieee80211_key_conf { 1867 atomic64_t tx_pn; 1868 u32 cipher; 1869 u8 icv_len; 1870 u8 iv_len; 1871 u8 hw_key_idx; 1872 s8 keyidx; 1873 u16 flags; 1874 u8 keylen; 1875 u8 key[]; 1876 }; 1877 1878 #define IEEE80211_MAX_PN_LEN 16 1879 1880 #define TKIP_PN_TO_IV16(pn) ((u16)(pn & 0xffff)) 1881 #define TKIP_PN_TO_IV32(pn) ((u32)((pn >> 16) & 0xffffffff)) 1882 1883 /** 1884 * struct ieee80211_key_seq - key sequence counter 1885 * 1886 * @tkip: TKIP data, containing IV32 and IV16 in host byte order 1887 * @ccmp: PN data, most significant byte first (big endian, 1888 * reverse order than in packet) 1889 * @aes_cmac: PN data, most significant byte first (big endian, 1890 * reverse order than in packet) 1891 * @aes_gmac: PN data, most significant byte first (big endian, 1892 * reverse order than in packet) 1893 * @gcmp: PN data, most significant byte first (big endian, 1894 * reverse order than in packet) 1895 * @hw: data for HW-only (e.g. cipher scheme) keys 1896 */ 1897 struct ieee80211_key_seq { 1898 union { 1899 struct { 1900 u32 iv32; 1901 u16 iv16; 1902 } tkip; 1903 struct { 1904 u8 pn[6]; 1905 } ccmp; 1906 struct { 1907 u8 pn[6]; 1908 } aes_cmac; 1909 struct { 1910 u8 pn[6]; 1911 } aes_gmac; 1912 struct { 1913 u8 pn[6]; 1914 } gcmp; 1915 struct { 1916 u8 seq[IEEE80211_MAX_PN_LEN]; 1917 u8 seq_len; 1918 } hw; 1919 }; 1920 }; 1921 1922 /** 1923 * struct ieee80211_cipher_scheme - cipher scheme 1924 * 1925 * This structure contains a cipher scheme information defining 1926 * the secure packet crypto handling. 1927 * 1928 * @cipher: a cipher suite selector 1929 * @iftype: a cipher iftype bit mask indicating an allowed cipher usage 1930 * @hdr_len: a length of a security header used the cipher 1931 * @pn_len: a length of a packet number in the security header 1932 * @pn_off: an offset of pn from the beginning of the security header 1933 * @key_idx_off: an offset of key index byte in the security header 1934 * @key_idx_mask: a bit mask of key_idx bits 1935 * @key_idx_shift: a bit shift needed to get key_idx 1936 * key_idx value calculation: 1937 * (sec_header_base[key_idx_off] & key_idx_mask) >> key_idx_shift 1938 * @mic_len: a mic length in bytes 1939 */ 1940 struct ieee80211_cipher_scheme { 1941 u32 cipher; 1942 u16 iftype; 1943 u8 hdr_len; 1944 u8 pn_len; 1945 u8 pn_off; 1946 u8 key_idx_off; 1947 u8 key_idx_mask; 1948 u8 key_idx_shift; 1949 u8 mic_len; 1950 }; 1951 1952 /** 1953 * enum set_key_cmd - key command 1954 * 1955 * Used with the set_key() callback in &struct ieee80211_ops, this 1956 * indicates whether a key is being removed or added. 1957 * 1958 * @SET_KEY: a key is set 1959 * @DISABLE_KEY: a key must be disabled 1960 */ 1961 enum set_key_cmd { 1962 SET_KEY, DISABLE_KEY, 1963 }; 1964 1965 /** 1966 * enum ieee80211_sta_state - station state 1967 * 1968 * @IEEE80211_STA_NOTEXIST: station doesn't exist at all, 1969 * this is a special state for add/remove transitions 1970 * @IEEE80211_STA_NONE: station exists without special state 1971 * @IEEE80211_STA_AUTH: station is authenticated 1972 * @IEEE80211_STA_ASSOC: station is associated 1973 * @IEEE80211_STA_AUTHORIZED: station is authorized (802.1X) 1974 */ 1975 enum ieee80211_sta_state { 1976 /* NOTE: These need to be ordered correctly! */ 1977 IEEE80211_STA_NOTEXIST, 1978 IEEE80211_STA_NONE, 1979 IEEE80211_STA_AUTH, 1980 IEEE80211_STA_ASSOC, 1981 IEEE80211_STA_AUTHORIZED, 1982 }; 1983 1984 /** 1985 * enum ieee80211_sta_rx_bandwidth - station RX bandwidth 1986 * @IEEE80211_STA_RX_BW_20: station can only receive 20 MHz 1987 * @IEEE80211_STA_RX_BW_40: station can receive up to 40 MHz 1988 * @IEEE80211_STA_RX_BW_80: station can receive up to 80 MHz 1989 * @IEEE80211_STA_RX_BW_160: station can receive up to 160 MHz 1990 * (including 80+80 MHz) 1991 * 1992 * Implementation note: 20 must be zero to be initialized 1993 * correctly, the values must be sorted. 1994 */ 1995 enum ieee80211_sta_rx_bandwidth { 1996 IEEE80211_STA_RX_BW_20 = 0, 1997 IEEE80211_STA_RX_BW_40, 1998 IEEE80211_STA_RX_BW_80, 1999 IEEE80211_STA_RX_BW_160, 2000 }; 2001 2002 /** 2003 * struct ieee80211_sta_rates - station rate selection table 2004 * 2005 * @rcu_head: RCU head used for freeing the table on update 2006 * @rate: transmit rates/flags to be used by default. 2007 * Overriding entries per-packet is possible by using cb tx control. 2008 */ 2009 struct ieee80211_sta_rates { 2010 struct rcu_head rcu_head; 2011 struct { 2012 s8 idx; 2013 u8 count; 2014 u8 count_cts; 2015 u8 count_rts; 2016 u16 flags; 2017 } rate[IEEE80211_TX_RATE_TABLE_SIZE]; 2018 }; 2019 2020 /** 2021 * struct ieee80211_sta_txpwr - station txpower configuration 2022 * 2023 * Used to configure txpower for station. 2024 * 2025 * @power: indicates the tx power, in dBm, to be used when sending data frames 2026 * to the STA. 2027 * @type: In particular if TPC %type is NL80211_TX_POWER_LIMITED then tx power 2028 * will be less than or equal to specified from userspace, whereas if TPC 2029 * %type is NL80211_TX_POWER_AUTOMATIC then it indicates default tx power. 2030 * NL80211_TX_POWER_FIXED is not a valid configuration option for 2031 * per peer TPC. 2032 */ 2033 struct ieee80211_sta_txpwr { 2034 s16 power; 2035 enum nl80211_tx_power_setting type; 2036 }; 2037 2038 /** 2039 * struct ieee80211_sta - station table entry 2040 * 2041 * A station table entry represents a station we are possibly 2042 * communicating with. Since stations are RCU-managed in 2043 * mac80211, any ieee80211_sta pointer you get access to must 2044 * either be protected by rcu_read_lock() explicitly or implicitly, 2045 * or you must take good care to not use such a pointer after a 2046 * call to your sta_remove callback that removed it. 2047 * 2048 * @addr: MAC address 2049 * @aid: AID we assigned to the station if we're an AP 2050 * @supp_rates: Bitmap of supported rates (per band) 2051 * @ht_cap: HT capabilities of this STA; restricted to our own capabilities 2052 * @vht_cap: VHT capabilities of this STA; restricted to our own capabilities 2053 * @he_cap: HE capabilities of this STA 2054 * @he_6ghz_capa: on 6 GHz, holds the HE 6 GHz band capabilities 2055 * @max_rx_aggregation_subframes: maximal amount of frames in a single AMPDU 2056 * that this station is allowed to transmit to us. 2057 * Can be modified by driver. 2058 * @wme: indicates whether the STA supports QoS/WME (if local devices does, 2059 * otherwise always false) 2060 * @drv_priv: data area for driver use, will always be aligned to 2061 * sizeof(void \*), size is determined in hw information. 2062 * @uapsd_queues: bitmap of queues configured for uapsd. Only valid 2063 * if wme is supported. The bits order is like in 2064 * IEEE80211_WMM_IE_STA_QOSINFO_AC_*. 2065 * @max_sp: max Service Period. Only valid if wme is supported. 2066 * @bandwidth: current bandwidth the station can receive with 2067 * @rx_nss: in HT/VHT, the maximum number of spatial streams the 2068 * station can receive at the moment, changed by operating mode 2069 * notifications and capabilities. The value is only valid after 2070 * the station moves to associated state. 2071 * @smps_mode: current SMPS mode (off, static or dynamic) 2072 * @rates: rate control selection table 2073 * @tdls: indicates whether the STA is a TDLS peer 2074 * @tdls_initiator: indicates the STA is an initiator of the TDLS link. Only 2075 * valid if the STA is a TDLS peer in the first place. 2076 * @mfp: indicates whether the STA uses management frame protection or not. 2077 * @max_amsdu_subframes: indicates the maximal number of MSDUs in a single 2078 * A-MSDU. Taken from the Extended Capabilities element. 0 means 2079 * unlimited. 2080 * @support_p2p_ps: indicates whether the STA supports P2P PS mechanism or not. 2081 * @max_rc_amsdu_len: Maximum A-MSDU size in bytes recommended by rate control. 2082 * @max_tid_amsdu_len: Maximum A-MSDU size in bytes for this TID 2083 * @txpwr: the station tx power configuration 2084 * @txq: per-TID data TX queues (if driver uses the TXQ abstraction); note that 2085 * the last entry (%IEEE80211_NUM_TIDS) is used for non-data frames 2086 */ 2087 struct ieee80211_sta { 2088 u32 supp_rates[NUM_NL80211_BANDS]; 2089 u8 addr[ETH_ALEN]; 2090 u16 aid; 2091 struct ieee80211_sta_ht_cap ht_cap; 2092 struct ieee80211_sta_vht_cap vht_cap; 2093 struct ieee80211_sta_he_cap he_cap; 2094 struct ieee80211_he_6ghz_capa he_6ghz_capa; 2095 u16 max_rx_aggregation_subframes; 2096 bool wme; 2097 u8 uapsd_queues; 2098 u8 max_sp; 2099 u8 rx_nss; 2100 enum ieee80211_sta_rx_bandwidth bandwidth; 2101 enum ieee80211_smps_mode smps_mode; 2102 struct ieee80211_sta_rates __rcu *rates; 2103 bool tdls; 2104 bool tdls_initiator; 2105 bool mfp; 2106 u8 max_amsdu_subframes; 2107 2108 /** 2109 * @max_amsdu_len: 2110 * indicates the maximal length of an A-MSDU in bytes. 2111 * This field is always valid for packets with a VHT preamble. 2112 * For packets with a HT preamble, additional limits apply: 2113 * 2114 * * If the skb is transmitted as part of a BA agreement, the 2115 * A-MSDU maximal size is min(max_amsdu_len, 4065) bytes. 2116 * * If the skb is not part of a BA agreement, the A-MSDU maximal 2117 * size is min(max_amsdu_len, 7935) bytes. 2118 * 2119 * Both additional HT limits must be enforced by the low level 2120 * driver. This is defined by the spec (IEEE 802.11-2012 section 2121 * 8.3.2.2 NOTE 2). 2122 */ 2123 u16 max_amsdu_len; 2124 bool support_p2p_ps; 2125 u16 max_rc_amsdu_len; 2126 u16 max_tid_amsdu_len[IEEE80211_NUM_TIDS]; 2127 struct ieee80211_sta_txpwr txpwr; 2128 2129 struct ieee80211_txq *txq[IEEE80211_NUM_TIDS + 1]; 2130 2131 /* must be last */ 2132 u8 drv_priv[] __aligned(sizeof(void *)); 2133 }; 2134 2135 /** 2136 * enum sta_notify_cmd - sta notify command 2137 * 2138 * Used with the sta_notify() callback in &struct ieee80211_ops, this 2139 * indicates if an associated station made a power state transition. 2140 * 2141 * @STA_NOTIFY_SLEEP: a station is now sleeping 2142 * @STA_NOTIFY_AWAKE: a sleeping station woke up 2143 */ 2144 enum sta_notify_cmd { 2145 STA_NOTIFY_SLEEP, STA_NOTIFY_AWAKE, 2146 }; 2147 2148 /** 2149 * struct ieee80211_tx_control - TX control data 2150 * 2151 * @sta: station table entry, this sta pointer may be NULL and 2152 * it is not allowed to copy the pointer, due to RCU. 2153 */ 2154 struct ieee80211_tx_control { 2155 struct ieee80211_sta *sta; 2156 }; 2157 2158 /** 2159 * struct ieee80211_txq - Software intermediate tx queue 2160 * 2161 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 2162 * @sta: station table entry, %NULL for per-vif queue 2163 * @tid: the TID for this queue (unused for per-vif queue), 2164 * %IEEE80211_NUM_TIDS for non-data (if enabled) 2165 * @ac: the AC for this queue 2166 * @drv_priv: driver private area, sized by hw->txq_data_size 2167 * 2168 * The driver can obtain packets from this queue by calling 2169 * ieee80211_tx_dequeue(). 2170 */ 2171 struct ieee80211_txq { 2172 struct ieee80211_vif *vif; 2173 struct ieee80211_sta *sta; 2174 u8 tid; 2175 u8 ac; 2176 2177 /* must be last */ 2178 u8 drv_priv[] __aligned(sizeof(void *)); 2179 }; 2180 2181 /** 2182 * enum ieee80211_hw_flags - hardware flags 2183 * 2184 * These flags are used to indicate hardware capabilities to 2185 * the stack. Generally, flags here should have their meaning 2186 * done in a way that the simplest hardware doesn't need setting 2187 * any particular flags. There are some exceptions to this rule, 2188 * however, so you are advised to review these flags carefully. 2189 * 2190 * @IEEE80211_HW_HAS_RATE_CONTROL: 2191 * The hardware or firmware includes rate control, and cannot be 2192 * controlled by the stack. As such, no rate control algorithm 2193 * should be instantiated, and the TX rate reported to userspace 2194 * will be taken from the TX status instead of the rate control 2195 * algorithm. 2196 * Note that this requires that the driver implement a number of 2197 * callbacks so it has the correct information, it needs to have 2198 * the @set_rts_threshold callback and must look at the BSS config 2199 * @use_cts_prot for G/N protection, @use_short_slot for slot 2200 * timing in 2.4 GHz and @use_short_preamble for preambles for 2201 * CCK frames. 2202 * 2203 * @IEEE80211_HW_RX_INCLUDES_FCS: 2204 * Indicates that received frames passed to the stack include 2205 * the FCS at the end. 2206 * 2207 * @IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING: 2208 * Some wireless LAN chipsets buffer broadcast/multicast frames 2209 * for power saving stations in the hardware/firmware and others 2210 * rely on the host system for such buffering. This option is used 2211 * to configure the IEEE 802.11 upper layer to buffer broadcast and 2212 * multicast frames when there are power saving stations so that 2213 * the driver can fetch them with ieee80211_get_buffered_bc(). 2214 * 2215 * @IEEE80211_HW_SIGNAL_UNSPEC: 2216 * Hardware can provide signal values but we don't know its units. We 2217 * expect values between 0 and @max_signal. 2218 * If possible please provide dB or dBm instead. 2219 * 2220 * @IEEE80211_HW_SIGNAL_DBM: 2221 * Hardware gives signal values in dBm, decibel difference from 2222 * one milliwatt. This is the preferred method since it is standardized 2223 * between different devices. @max_signal does not need to be set. 2224 * 2225 * @IEEE80211_HW_SPECTRUM_MGMT: 2226 * Hardware supports spectrum management defined in 802.11h 2227 * Measurement, Channel Switch, Quieting, TPC 2228 * 2229 * @IEEE80211_HW_AMPDU_AGGREGATION: 2230 * Hardware supports 11n A-MPDU aggregation. 2231 * 2232 * @IEEE80211_HW_SUPPORTS_PS: 2233 * Hardware has power save support (i.e. can go to sleep). 2234 * 2235 * @IEEE80211_HW_PS_NULLFUNC_STACK: 2236 * Hardware requires nullfunc frame handling in stack, implies 2237 * stack support for dynamic PS. 2238 * 2239 * @IEEE80211_HW_SUPPORTS_DYNAMIC_PS: 2240 * Hardware has support for dynamic PS. 2241 * 2242 * @IEEE80211_HW_MFP_CAPABLE: 2243 * Hardware supports management frame protection (MFP, IEEE 802.11w). 2244 * 2245 * @IEEE80211_HW_REPORTS_TX_ACK_STATUS: 2246 * Hardware can provide ack status reports of Tx frames to 2247 * the stack. 2248 * 2249 * @IEEE80211_HW_CONNECTION_MONITOR: 2250 * The hardware performs its own connection monitoring, including 2251 * periodic keep-alives to the AP and probing the AP on beacon loss. 2252 * 2253 * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC: 2254 * This device needs to get data from beacon before association (i.e. 2255 * dtim_period). 2256 * 2257 * @IEEE80211_HW_SUPPORTS_PER_STA_GTK: The device's crypto engine supports 2258 * per-station GTKs as used by IBSS RSN or during fast transition. If 2259 * the device doesn't support per-station GTKs, but can be asked not 2260 * to decrypt group addressed frames, then IBSS RSN support is still 2261 * possible but software crypto will be used. Advertise the wiphy flag 2262 * only in that case. 2263 * 2264 * @IEEE80211_HW_AP_LINK_PS: When operating in AP mode the device 2265 * autonomously manages the PS status of connected stations. When 2266 * this flag is set mac80211 will not trigger PS mode for connected 2267 * stations based on the PM bit of incoming frames. 2268 * Use ieee80211_start_ps()/ieee8021_end_ps() to manually configure 2269 * the PS mode of connected stations. 2270 * 2271 * @IEEE80211_HW_TX_AMPDU_SETUP_IN_HW: The device handles TX A-MPDU session 2272 * setup strictly in HW. mac80211 should not attempt to do this in 2273 * software. 2274 * 2275 * @IEEE80211_HW_WANT_MONITOR_VIF: The driver would like to be informed of 2276 * a virtual monitor interface when monitor interfaces are the only 2277 * active interfaces. 2278 * 2279 * @IEEE80211_HW_NO_AUTO_VIF: The driver would like for no wlanX to 2280 * be created. It is expected user-space will create vifs as 2281 * desired (and thus have them named as desired). 2282 * 2283 * @IEEE80211_HW_SW_CRYPTO_CONTROL: The driver wants to control which of the 2284 * crypto algorithms can be done in software - so don't automatically 2285 * try to fall back to it if hardware crypto fails, but do so only if 2286 * the driver returns 1. This also forces the driver to advertise its 2287 * supported cipher suites. 2288 * 2289 * @IEEE80211_HW_SUPPORT_FAST_XMIT: The driver/hardware supports fast-xmit, 2290 * this currently requires only the ability to calculate the duration 2291 * for frames. 2292 * 2293 * @IEEE80211_HW_QUEUE_CONTROL: The driver wants to control per-interface 2294 * queue mapping in order to use different queues (not just one per AC) 2295 * for different virtual interfaces. See the doc section on HW queue 2296 * control for more details. 2297 * 2298 * @IEEE80211_HW_SUPPORTS_RC_TABLE: The driver supports using a rate 2299 * selection table provided by the rate control algorithm. 2300 * 2301 * @IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF: Use the P2P Device address for any 2302 * P2P Interface. This will be honoured even if more than one interface 2303 * is supported. 2304 * 2305 * @IEEE80211_HW_TIMING_BEACON_ONLY: Use sync timing from beacon frames 2306 * only, to allow getting TBTT of a DTIM beacon. 2307 * 2308 * @IEEE80211_HW_SUPPORTS_HT_CCK_RATES: Hardware supports mixing HT/CCK rates 2309 * and can cope with CCK rates in an aggregation session (e.g. by not 2310 * using aggregation for such frames.) 2311 * 2312 * @IEEE80211_HW_CHANCTX_STA_CSA: Support 802.11h based channel-switch (CSA) 2313 * for a single active channel while using channel contexts. When support 2314 * is not enabled the default action is to disconnect when getting the 2315 * CSA frame. 2316 * 2317 * @IEEE80211_HW_SUPPORTS_CLONED_SKBS: The driver will never modify the payload 2318 * or tailroom of TX skbs without copying them first. 2319 * 2320 * @IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS: The HW supports scanning on all bands 2321 * in one command, mac80211 doesn't have to run separate scans per band. 2322 * 2323 * @IEEE80211_HW_TDLS_WIDER_BW: The device/driver supports wider bandwidth 2324 * than then BSS bandwidth for a TDLS link on the base channel. 2325 * 2326 * @IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU: The driver supports receiving A-MSDUs 2327 * within A-MPDU. 2328 * 2329 * @IEEE80211_HW_BEACON_TX_STATUS: The device/driver provides TX status 2330 * for sent beacons. 2331 * 2332 * @IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR: Hardware (or driver) requires that each 2333 * station has a unique address, i.e. each station entry can be identified 2334 * by just its MAC address; this prevents, for example, the same station 2335 * from connecting to two virtual AP interfaces at the same time. 2336 * 2337 * @IEEE80211_HW_SUPPORTS_REORDERING_BUFFER: Hardware (or driver) manages the 2338 * reordering buffer internally, guaranteeing mac80211 receives frames in 2339 * order and does not need to manage its own reorder buffer or BA session 2340 * timeout. 2341 * 2342 * @IEEE80211_HW_USES_RSS: The device uses RSS and thus requires parallel RX, 2343 * which implies using per-CPU station statistics. 2344 * 2345 * @IEEE80211_HW_TX_AMSDU: Hardware (or driver) supports software aggregated 2346 * A-MSDU frames. Requires software tx queueing and fast-xmit support. 2347 * When not using minstrel/minstrel_ht rate control, the driver must 2348 * limit the maximum A-MSDU size based on the current tx rate by setting 2349 * max_rc_amsdu_len in struct ieee80211_sta. 2350 * 2351 * @IEEE80211_HW_TX_FRAG_LIST: Hardware (or driver) supports sending frag_list 2352 * skbs, needed for zero-copy software A-MSDU. 2353 * 2354 * @IEEE80211_HW_REPORTS_LOW_ACK: The driver (or firmware) reports low ack event 2355 * by ieee80211_report_low_ack() based on its own algorithm. For such 2356 * drivers, mac80211 packet loss mechanism will not be triggered and driver 2357 * is completely depending on firmware event for station kickout. 2358 * 2359 * @IEEE80211_HW_SUPPORTS_TX_FRAG: Hardware does fragmentation by itself. 2360 * The stack will not do fragmentation. 2361 * The callback for @set_frag_threshold should be set as well. 2362 * 2363 * @IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA: Hardware supports buffer STA on 2364 * TDLS links. 2365 * 2366 * @IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP: The driver requires the 2367 * mgd_prepare_tx() callback to be called before transmission of a 2368 * deauthentication frame in case the association was completed but no 2369 * beacon was heard. This is required in multi-channel scenarios, where the 2370 * virtual interface might not be given air time for the transmission of 2371 * the frame, as it is not synced with the AP/P2P GO yet, and thus the 2372 * deauthentication frame might not be transmitted. 2373 * 2374 * @IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP: The driver (or firmware) doesn't 2375 * support QoS NDP for AP probing - that's most likely a driver bug. 2376 * 2377 * @IEEE80211_HW_BUFF_MMPDU_TXQ: use the TXQ for bufferable MMPDUs, this of 2378 * course requires the driver to use TXQs to start with. 2379 * 2380 * @IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW: (Hardware) rate control supports VHT 2381 * extended NSS BW (dot11VHTExtendedNSSBWCapable). This flag will be set if 2382 * the selected rate control algorithm sets %RATE_CTRL_CAPA_VHT_EXT_NSS_BW 2383 * but if the rate control is built-in then it must be set by the driver. 2384 * See also the documentation for that flag. 2385 * 2386 * @IEEE80211_HW_STA_MMPDU_TXQ: use the extra non-TID per-station TXQ for all 2387 * MMPDUs on station interfaces. This of course requires the driver to use 2388 * TXQs to start with. 2389 * 2390 * @IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN: Driver does not report accurate A-MPDU 2391 * length in tx status information 2392 * 2393 * @IEEE80211_HW_SUPPORTS_MULTI_BSSID: Hardware supports multi BSSID 2394 * 2395 * @IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID: Hardware supports multi BSSID 2396 * only for HE APs. Applies if @IEEE80211_HW_SUPPORTS_MULTI_BSSID is set. 2397 * 2398 * @IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT: The card and driver is only 2399 * aggregating MPDUs with the same keyid, allowing mac80211 to keep Tx 2400 * A-MPDU sessions active while rekeying with Extended Key ID. 2401 * 2402 * @IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD: Hardware supports tx encapsulation 2403 * offload 2404 * 2405 * @IEEE80211_HW_SUPPORTS_RX_DECAP_OFFLOAD: Hardware supports rx decapsulation 2406 * offload 2407 * 2408 * @IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP: Hardware supports concurrent rx 2409 * decapsulation offload and passing raw 802.11 frames for monitor iface. 2410 * If this is supported, the driver must pass both 802.3 frames for real 2411 * usage and 802.11 frames with %RX_FLAG_ONLY_MONITOR set for monitor to 2412 * the stack. 2413 * 2414 * @NUM_IEEE80211_HW_FLAGS: number of hardware flags, used for sizing arrays 2415 */ 2416 enum ieee80211_hw_flags { 2417 IEEE80211_HW_HAS_RATE_CONTROL, 2418 IEEE80211_HW_RX_INCLUDES_FCS, 2419 IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING, 2420 IEEE80211_HW_SIGNAL_UNSPEC, 2421 IEEE80211_HW_SIGNAL_DBM, 2422 IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC, 2423 IEEE80211_HW_SPECTRUM_MGMT, 2424 IEEE80211_HW_AMPDU_AGGREGATION, 2425 IEEE80211_HW_SUPPORTS_PS, 2426 IEEE80211_HW_PS_NULLFUNC_STACK, 2427 IEEE80211_HW_SUPPORTS_DYNAMIC_PS, 2428 IEEE80211_HW_MFP_CAPABLE, 2429 IEEE80211_HW_WANT_MONITOR_VIF, 2430 IEEE80211_HW_NO_AUTO_VIF, 2431 IEEE80211_HW_SW_CRYPTO_CONTROL, 2432 IEEE80211_HW_SUPPORT_FAST_XMIT, 2433 IEEE80211_HW_REPORTS_TX_ACK_STATUS, 2434 IEEE80211_HW_CONNECTION_MONITOR, 2435 IEEE80211_HW_QUEUE_CONTROL, 2436 IEEE80211_HW_SUPPORTS_PER_STA_GTK, 2437 IEEE80211_HW_AP_LINK_PS, 2438 IEEE80211_HW_TX_AMPDU_SETUP_IN_HW, 2439 IEEE80211_HW_SUPPORTS_RC_TABLE, 2440 IEEE80211_HW_P2P_DEV_ADDR_FOR_INTF, 2441 IEEE80211_HW_TIMING_BEACON_ONLY, 2442 IEEE80211_HW_SUPPORTS_HT_CCK_RATES, 2443 IEEE80211_HW_CHANCTX_STA_CSA, 2444 IEEE80211_HW_SUPPORTS_CLONED_SKBS, 2445 IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS, 2446 IEEE80211_HW_TDLS_WIDER_BW, 2447 IEEE80211_HW_SUPPORTS_AMSDU_IN_AMPDU, 2448 IEEE80211_HW_BEACON_TX_STATUS, 2449 IEEE80211_HW_NEEDS_UNIQUE_STA_ADDR, 2450 IEEE80211_HW_SUPPORTS_REORDERING_BUFFER, 2451 IEEE80211_HW_USES_RSS, 2452 IEEE80211_HW_TX_AMSDU, 2453 IEEE80211_HW_TX_FRAG_LIST, 2454 IEEE80211_HW_REPORTS_LOW_ACK, 2455 IEEE80211_HW_SUPPORTS_TX_FRAG, 2456 IEEE80211_HW_SUPPORTS_TDLS_BUFFER_STA, 2457 IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP, 2458 IEEE80211_HW_DOESNT_SUPPORT_QOS_NDP, 2459 IEEE80211_HW_BUFF_MMPDU_TXQ, 2460 IEEE80211_HW_SUPPORTS_VHT_EXT_NSS_BW, 2461 IEEE80211_HW_STA_MMPDU_TXQ, 2462 IEEE80211_HW_TX_STATUS_NO_AMPDU_LEN, 2463 IEEE80211_HW_SUPPORTS_MULTI_BSSID, 2464 IEEE80211_HW_SUPPORTS_ONLY_HE_MULTI_BSSID, 2465 IEEE80211_HW_AMPDU_KEYBORDER_SUPPORT, 2466 IEEE80211_HW_SUPPORTS_TX_ENCAP_OFFLOAD, 2467 IEEE80211_HW_SUPPORTS_RX_DECAP_OFFLOAD, 2468 IEEE80211_HW_SUPPORTS_CONC_MON_RX_DECAP, 2469 2470 /* keep last, obviously */ 2471 NUM_IEEE80211_HW_FLAGS 2472 }; 2473 2474 /** 2475 * struct ieee80211_hw - hardware information and state 2476 * 2477 * This structure contains the configuration and hardware 2478 * information for an 802.11 PHY. 2479 * 2480 * @wiphy: This points to the &struct wiphy allocated for this 2481 * 802.11 PHY. You must fill in the @perm_addr and @dev 2482 * members of this structure using SET_IEEE80211_DEV() 2483 * and SET_IEEE80211_PERM_ADDR(). Additionally, all supported 2484 * bands (with channels, bitrates) are registered here. 2485 * 2486 * @conf: &struct ieee80211_conf, device configuration, don't use. 2487 * 2488 * @priv: pointer to private area that was allocated for driver use 2489 * along with this structure. 2490 * 2491 * @flags: hardware flags, see &enum ieee80211_hw_flags. 2492 * 2493 * @extra_tx_headroom: headroom to reserve in each transmit skb 2494 * for use by the driver (e.g. for transmit headers.) 2495 * 2496 * @extra_beacon_tailroom: tailroom to reserve in each beacon tx skb. 2497 * Can be used by drivers to add extra IEs. 2498 * 2499 * @max_signal: Maximum value for signal (rssi) in RX information, used 2500 * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB 2501 * 2502 * @max_listen_interval: max listen interval in units of beacon interval 2503 * that HW supports 2504 * 2505 * @queues: number of available hardware transmit queues for 2506 * data packets. WMM/QoS requires at least four, these 2507 * queues need to have configurable access parameters. 2508 * 2509 * @rate_control_algorithm: rate control algorithm for this hardware. 2510 * If unset (NULL), the default algorithm will be used. Must be 2511 * set before calling ieee80211_register_hw(). 2512 * 2513 * @vif_data_size: size (in bytes) of the drv_priv data area 2514 * within &struct ieee80211_vif. 2515 * @sta_data_size: size (in bytes) of the drv_priv data area 2516 * within &struct ieee80211_sta. 2517 * @chanctx_data_size: size (in bytes) of the drv_priv data area 2518 * within &struct ieee80211_chanctx_conf. 2519 * @txq_data_size: size (in bytes) of the drv_priv data area 2520 * within @struct ieee80211_txq. 2521 * 2522 * @max_rates: maximum number of alternate rate retry stages the hw 2523 * can handle. 2524 * @max_report_rates: maximum number of alternate rate retry stages 2525 * the hw can report back. 2526 * @max_rate_tries: maximum number of tries for each stage 2527 * 2528 * @max_rx_aggregation_subframes: maximum buffer size (number of 2529 * sub-frames) to be used for A-MPDU block ack receiver 2530 * aggregation. 2531 * This is only relevant if the device has restrictions on the 2532 * number of subframes, if it relies on mac80211 to do reordering 2533 * it shouldn't be set. 2534 * 2535 * @max_tx_aggregation_subframes: maximum number of subframes in an 2536 * aggregate an HT/HE device will transmit. In HT AddBA we'll 2537 * advertise a constant value of 64 as some older APs crash if 2538 * the window size is smaller (an example is LinkSys WRT120N 2539 * with FW v1.0.07 build 002 Jun 18 2012). 2540 * For AddBA to HE capable peers this value will be used. 2541 * 2542 * @max_tx_fragments: maximum number of tx buffers per (A)-MSDU, sum 2543 * of 1 + skb_shinfo(skb)->nr_frags for each skb in the frag_list. 2544 * 2545 * @offchannel_tx_hw_queue: HW queue ID to use for offchannel TX 2546 * (if %IEEE80211_HW_QUEUE_CONTROL is set) 2547 * 2548 * @radiotap_mcs_details: lists which MCS information can the HW 2549 * reports, by default it is set to _MCS, _GI and _BW but doesn't 2550 * include _FMT. Use %IEEE80211_RADIOTAP_MCS_HAVE_\* values, only 2551 * adding _BW is supported today. 2552 * 2553 * @radiotap_vht_details: lists which VHT MCS information the HW reports, 2554 * the default is _GI | _BANDWIDTH. 2555 * Use the %IEEE80211_RADIOTAP_VHT_KNOWN_\* values. 2556 * 2557 * @radiotap_he: HE radiotap validity flags 2558 * 2559 * @radiotap_timestamp: Information for the radiotap timestamp field; if the 2560 * @units_pos member is set to a non-negative value then the timestamp 2561 * field will be added and populated from the &struct ieee80211_rx_status 2562 * device_timestamp. 2563 * @radiotap_timestamp.units_pos: Must be set to a combination of a 2564 * IEEE80211_RADIOTAP_TIMESTAMP_UNIT_* and a 2565 * IEEE80211_RADIOTAP_TIMESTAMP_SPOS_* value. 2566 * @radiotap_timestamp.accuracy: If non-negative, fills the accuracy in the 2567 * radiotap field and the accuracy known flag will be set. 2568 * 2569 * @netdev_features: netdev features to be set in each netdev created 2570 * from this HW. Note that not all features are usable with mac80211, 2571 * other features will be rejected during HW registration. 2572 * 2573 * @uapsd_queues: This bitmap is included in (re)association frame to indicate 2574 * for each access category if it is uAPSD trigger-enabled and delivery- 2575 * enabled. Use IEEE80211_WMM_IE_STA_QOSINFO_AC_* to set this bitmap. 2576 * Each bit corresponds to different AC. Value '1' in specific bit means 2577 * that corresponding AC is both trigger- and delivery-enabled. '0' means 2578 * neither enabled. 2579 * 2580 * @uapsd_max_sp_len: maximum number of total buffered frames the WMM AP may 2581 * deliver to a WMM STA during any Service Period triggered by the WMM STA. 2582 * Use IEEE80211_WMM_IE_STA_QOSINFO_SP_* for correct values. 2583 * 2584 * @n_cipher_schemes: a size of an array of cipher schemes definitions. 2585 * @cipher_schemes: a pointer to an array of cipher scheme definitions 2586 * supported by HW. 2587 * @max_nan_de_entries: maximum number of NAN DE functions supported by the 2588 * device. 2589 * 2590 * @tx_sk_pacing_shift: Pacing shift to set on TCP sockets when frames from 2591 * them are encountered. The default should typically not be changed, 2592 * unless the driver has good reasons for needing more buffers. 2593 * 2594 * @weight_multiplier: Driver specific airtime weight multiplier used while 2595 * refilling deficit of each TXQ. 2596 * 2597 * @max_mtu: the max mtu could be set. 2598 */ 2599 struct ieee80211_hw { 2600 struct ieee80211_conf conf; 2601 struct wiphy *wiphy; 2602 const char *rate_control_algorithm; 2603 void *priv; 2604 unsigned long flags[BITS_TO_LONGS(NUM_IEEE80211_HW_FLAGS)]; 2605 unsigned int extra_tx_headroom; 2606 unsigned int extra_beacon_tailroom; 2607 int vif_data_size; 2608 int sta_data_size; 2609 int chanctx_data_size; 2610 int txq_data_size; 2611 u16 queues; 2612 u16 max_listen_interval; 2613 s8 max_signal; 2614 u8 max_rates; 2615 u8 max_report_rates; 2616 u8 max_rate_tries; 2617 u16 max_rx_aggregation_subframes; 2618 u16 max_tx_aggregation_subframes; 2619 u8 max_tx_fragments; 2620 u8 offchannel_tx_hw_queue; 2621 u8 radiotap_mcs_details; 2622 u16 radiotap_vht_details; 2623 struct { 2624 int units_pos; 2625 s16 accuracy; 2626 } radiotap_timestamp; 2627 netdev_features_t netdev_features; 2628 u8 uapsd_queues; 2629 u8 uapsd_max_sp_len; 2630 u8 n_cipher_schemes; 2631 const struct ieee80211_cipher_scheme *cipher_schemes; 2632 u8 max_nan_de_entries; 2633 u8 tx_sk_pacing_shift; 2634 u8 weight_multiplier; 2635 u32 max_mtu; 2636 }; 2637 2638 static inline bool _ieee80211_hw_check(struct ieee80211_hw *hw, 2639 enum ieee80211_hw_flags flg) 2640 { 2641 return test_bit(flg, hw->flags); 2642 } 2643 #define ieee80211_hw_check(hw, flg) _ieee80211_hw_check(hw, IEEE80211_HW_##flg) 2644 2645 static inline void _ieee80211_hw_set(struct ieee80211_hw *hw, 2646 enum ieee80211_hw_flags flg) 2647 { 2648 return __set_bit(flg, hw->flags); 2649 } 2650 #define ieee80211_hw_set(hw, flg) _ieee80211_hw_set(hw, IEEE80211_HW_##flg) 2651 2652 /** 2653 * struct ieee80211_scan_request - hw scan request 2654 * 2655 * @ies: pointers different parts of IEs (in req.ie) 2656 * @req: cfg80211 request. 2657 */ 2658 struct ieee80211_scan_request { 2659 struct ieee80211_scan_ies ies; 2660 2661 /* Keep last */ 2662 struct cfg80211_scan_request req; 2663 }; 2664 2665 /** 2666 * struct ieee80211_tdls_ch_sw_params - TDLS channel switch parameters 2667 * 2668 * @sta: peer this TDLS channel-switch request/response came from 2669 * @chandef: channel referenced in a TDLS channel-switch request 2670 * @action_code: see &enum ieee80211_tdls_actioncode 2671 * @status: channel-switch response status 2672 * @timestamp: time at which the frame was received 2673 * @switch_time: switch-timing parameter received in the frame 2674 * @switch_timeout: switch-timing parameter received in the frame 2675 * @tmpl_skb: TDLS switch-channel response template 2676 * @ch_sw_tm_ie: offset of the channel-switch timing IE inside @tmpl_skb 2677 */ 2678 struct ieee80211_tdls_ch_sw_params { 2679 struct ieee80211_sta *sta; 2680 struct cfg80211_chan_def *chandef; 2681 u8 action_code; 2682 u32 status; 2683 u32 timestamp; 2684 u16 switch_time; 2685 u16 switch_timeout; 2686 struct sk_buff *tmpl_skb; 2687 u32 ch_sw_tm_ie; 2688 }; 2689 2690 /** 2691 * wiphy_to_ieee80211_hw - return a mac80211 driver hw struct from a wiphy 2692 * 2693 * @wiphy: the &struct wiphy which we want to query 2694 * 2695 * mac80211 drivers can use this to get to their respective 2696 * &struct ieee80211_hw. Drivers wishing to get to their own private 2697 * structure can then access it via hw->priv. Note that mac802111 drivers should 2698 * not use wiphy_priv() to try to get their private driver structure as this 2699 * is already used internally by mac80211. 2700 * 2701 * Return: The mac80211 driver hw struct of @wiphy. 2702 */ 2703 struct ieee80211_hw *wiphy_to_ieee80211_hw(struct wiphy *wiphy); 2704 2705 /** 2706 * SET_IEEE80211_DEV - set device for 802.11 hardware 2707 * 2708 * @hw: the &struct ieee80211_hw to set the device for 2709 * @dev: the &struct device of this 802.11 device 2710 */ 2711 static inline void SET_IEEE80211_DEV(struct ieee80211_hw *hw, struct device *dev) 2712 { 2713 set_wiphy_dev(hw->wiphy, dev); 2714 } 2715 2716 /** 2717 * SET_IEEE80211_PERM_ADDR - set the permanent MAC address for 802.11 hardware 2718 * 2719 * @hw: the &struct ieee80211_hw to set the MAC address for 2720 * @addr: the address to set 2721 */ 2722 static inline void SET_IEEE80211_PERM_ADDR(struct ieee80211_hw *hw, const u8 *addr) 2723 { 2724 memcpy(hw->wiphy->perm_addr, addr, ETH_ALEN); 2725 } 2726 2727 static inline struct ieee80211_rate * 2728 ieee80211_get_tx_rate(const struct ieee80211_hw *hw, 2729 const struct ieee80211_tx_info *c) 2730 { 2731 if (WARN_ON_ONCE(c->control.rates[0].idx < 0)) 2732 return NULL; 2733 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[0].idx]; 2734 } 2735 2736 static inline struct ieee80211_rate * 2737 ieee80211_get_rts_cts_rate(const struct ieee80211_hw *hw, 2738 const struct ieee80211_tx_info *c) 2739 { 2740 if (c->control.rts_cts_rate_idx < 0) 2741 return NULL; 2742 return &hw->wiphy->bands[c->band]->bitrates[c->control.rts_cts_rate_idx]; 2743 } 2744 2745 static inline struct ieee80211_rate * 2746 ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, 2747 const struct ieee80211_tx_info *c, int idx) 2748 { 2749 if (c->control.rates[idx + 1].idx < 0) 2750 return NULL; 2751 return &hw->wiphy->bands[c->band]->bitrates[c->control.rates[idx + 1].idx]; 2752 } 2753 2754 /** 2755 * ieee80211_free_txskb - free TX skb 2756 * @hw: the hardware 2757 * @skb: the skb 2758 * 2759 * Free a transmit skb. Use this function when some failure 2760 * to transmit happened and thus status cannot be reported. 2761 */ 2762 void ieee80211_free_txskb(struct ieee80211_hw *hw, struct sk_buff *skb); 2763 2764 /** 2765 * DOC: Hardware crypto acceleration 2766 * 2767 * mac80211 is capable of taking advantage of many hardware 2768 * acceleration designs for encryption and decryption operations. 2769 * 2770 * The set_key() callback in the &struct ieee80211_ops for a given 2771 * device is called to enable hardware acceleration of encryption and 2772 * decryption. The callback takes a @sta parameter that will be NULL 2773 * for default keys or keys used for transmission only, or point to 2774 * the station information for the peer for individual keys. 2775 * Multiple transmission keys with the same key index may be used when 2776 * VLANs are configured for an access point. 2777 * 2778 * When transmitting, the TX control data will use the @hw_key_idx 2779 * selected by the driver by modifying the &struct ieee80211_key_conf 2780 * pointed to by the @key parameter to the set_key() function. 2781 * 2782 * The set_key() call for the %SET_KEY command should return 0 if 2783 * the key is now in use, -%EOPNOTSUPP or -%ENOSPC if it couldn't be 2784 * added; if you return 0 then hw_key_idx must be assigned to the 2785 * hardware key index, you are free to use the full u8 range. 2786 * 2787 * Note that in the case that the @IEEE80211_HW_SW_CRYPTO_CONTROL flag is 2788 * set, mac80211 will not automatically fall back to software crypto if 2789 * enabling hardware crypto failed. The set_key() call may also return the 2790 * value 1 to permit this specific key/algorithm to be done in software. 2791 * 2792 * When the cmd is %DISABLE_KEY then it must succeed. 2793 * 2794 * Note that it is permissible to not decrypt a frame even if a key 2795 * for it has been uploaded to hardware, the stack will not make any 2796 * decision based on whether a key has been uploaded or not but rather 2797 * based on the receive flags. 2798 * 2799 * The &struct ieee80211_key_conf structure pointed to by the @key 2800 * parameter is guaranteed to be valid until another call to set_key() 2801 * removes it, but it can only be used as a cookie to differentiate 2802 * keys. 2803 * 2804 * In TKIP some HW need to be provided a phase 1 key, for RX decryption 2805 * acceleration (i.e. iwlwifi). Those drivers should provide update_tkip_key 2806 * handler. 2807 * The update_tkip_key() call updates the driver with the new phase 1 key. 2808 * This happens every time the iv16 wraps around (every 65536 packets). The 2809 * set_key() call will happen only once for each key (unless the AP did 2810 * rekeying), it will not include a valid phase 1 key. The valid phase 1 key is 2811 * provided by update_tkip_key only. The trigger that makes mac80211 call this 2812 * handler is software decryption with wrap around of iv16. 2813 * 2814 * The set_default_unicast_key() call updates the default WEP key index 2815 * configured to the hardware for WEP encryption type. This is required 2816 * for devices that support offload of data packets (e.g. ARP responses). 2817 * 2818 * Mac80211 drivers should set the @NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 flag 2819 * when they are able to replace in-use PTK keys according to the following 2820 * requirements: 2821 * 1) They do not hand over frames decrypted with the old key to mac80211 2822 once the call to set_key() with command %DISABLE_KEY has been completed, 2823 2) either drop or continue to use the old key for any outgoing frames queued 2824 at the time of the key deletion (including re-transmits), 2825 3) never send out a frame queued prior to the set_key() %SET_KEY command 2826 encrypted with the new key when also needing 2827 @IEEE80211_KEY_FLAG_GENERATE_IV and 2828 4) never send out a frame unencrypted when it should be encrypted. 2829 Mac80211 will not queue any new frames for a deleted key to the driver. 2830 */ 2831 2832 /** 2833 * DOC: Powersave support 2834 * 2835 * mac80211 has support for various powersave implementations. 2836 * 2837 * First, it can support hardware that handles all powersaving by itself, 2838 * such hardware should simply set the %IEEE80211_HW_SUPPORTS_PS hardware 2839 * flag. In that case, it will be told about the desired powersave mode 2840 * with the %IEEE80211_CONF_PS flag depending on the association status. 2841 * The hardware must take care of sending nullfunc frames when necessary, 2842 * i.e. when entering and leaving powersave mode. The hardware is required 2843 * to look at the AID in beacons and signal to the AP that it woke up when 2844 * it finds traffic directed to it. 2845 * 2846 * %IEEE80211_CONF_PS flag enabled means that the powersave mode defined in 2847 * IEEE 802.11-2007 section 11.2 is enabled. This is not to be confused 2848 * with hardware wakeup and sleep states. Driver is responsible for waking 2849 * up the hardware before issuing commands to the hardware and putting it 2850 * back to sleep at appropriate times. 2851 * 2852 * When PS is enabled, hardware needs to wakeup for beacons and receive the 2853 * buffered multicast/broadcast frames after the beacon. Also it must be 2854 * possible to send frames and receive the acknowledment frame. 2855 * 2856 * Other hardware designs cannot send nullfunc frames by themselves and also 2857 * need software support for parsing the TIM bitmap. This is also supported 2858 * by mac80211 by combining the %IEEE80211_HW_SUPPORTS_PS and 2859 * %IEEE80211_HW_PS_NULLFUNC_STACK flags. The hardware is of course still 2860 * required to pass up beacons. The hardware is still required to handle 2861 * waking up for multicast traffic; if it cannot the driver must handle that 2862 * as best as it can, mac80211 is too slow to do that. 2863 * 2864 * Dynamic powersave is an extension to normal powersave in which the 2865 * hardware stays awake for a user-specified period of time after sending a 2866 * frame so that reply frames need not be buffered and therefore delayed to 2867 * the next wakeup. It's compromise of getting good enough latency when 2868 * there's data traffic and still saving significantly power in idle 2869 * periods. 2870 * 2871 * Dynamic powersave is simply supported by mac80211 enabling and disabling 2872 * PS based on traffic. Driver needs to only set %IEEE80211_HW_SUPPORTS_PS 2873 * flag and mac80211 will handle everything automatically. Additionally, 2874 * hardware having support for the dynamic PS feature may set the 2875 * %IEEE80211_HW_SUPPORTS_DYNAMIC_PS flag to indicate that it can support 2876 * dynamic PS mode itself. The driver needs to look at the 2877 * @dynamic_ps_timeout hardware configuration value and use it that value 2878 * whenever %IEEE80211_CONF_PS is set. In this case mac80211 will disable 2879 * dynamic PS feature in stack and will just keep %IEEE80211_CONF_PS 2880 * enabled whenever user has enabled powersave. 2881 * 2882 * Driver informs U-APSD client support by enabling 2883 * %IEEE80211_VIF_SUPPORTS_UAPSD flag. The mode is configured through the 2884 * uapsd parameter in conf_tx() operation. Hardware needs to send the QoS 2885 * Nullfunc frames and stay awake until the service period has ended. To 2886 * utilize U-APSD, dynamic powersave is disabled for voip AC and all frames 2887 * from that AC are transmitted with powersave enabled. 2888 * 2889 * Note: U-APSD client mode is not yet supported with 2890 * %IEEE80211_HW_PS_NULLFUNC_STACK. 2891 */ 2892 2893 /** 2894 * DOC: Beacon filter support 2895 * 2896 * Some hardware have beacon filter support to reduce host cpu wakeups 2897 * which will reduce system power consumption. It usually works so that 2898 * the firmware creates a checksum of the beacon but omits all constantly 2899 * changing elements (TSF, TIM etc). Whenever the checksum changes the 2900 * beacon is forwarded to the host, otherwise it will be just dropped. That 2901 * way the host will only receive beacons where some relevant information 2902 * (for example ERP protection or WMM settings) have changed. 2903 * 2904 * Beacon filter support is advertised with the %IEEE80211_VIF_BEACON_FILTER 2905 * interface capability. The driver needs to enable beacon filter support 2906 * whenever power save is enabled, that is %IEEE80211_CONF_PS is set. When 2907 * power save is enabled, the stack will not check for beacon loss and the 2908 * driver needs to notify about loss of beacons with ieee80211_beacon_loss(). 2909 * 2910 * The time (or number of beacons missed) until the firmware notifies the 2911 * driver of a beacon loss event (which in turn causes the driver to call 2912 * ieee80211_beacon_loss()) should be configurable and will be controlled 2913 * by mac80211 and the roaming algorithm in the future. 2914 * 2915 * Since there may be constantly changing information elements that nothing 2916 * in the software stack cares about, we will, in the future, have mac80211 2917 * tell the driver which information elements are interesting in the sense 2918 * that we want to see changes in them. This will include 2919 * 2920 * - a list of information element IDs 2921 * - a list of OUIs for the vendor information element 2922 * 2923 * Ideally, the hardware would filter out any beacons without changes in the 2924 * requested elements, but if it cannot support that it may, at the expense 2925 * of some efficiency, filter out only a subset. For example, if the device 2926 * doesn't support checking for OUIs it should pass up all changes in all 2927 * vendor information elements. 2928 * 2929 * Note that change, for the sake of simplification, also includes information 2930 * elements appearing or disappearing from the beacon. 2931 * 2932 * Some hardware supports an "ignore list" instead, just make sure nothing 2933 * that was requested is on the ignore list, and include commonly changing 2934 * information element IDs in the ignore list, for example 11 (BSS load) and 2935 * the various vendor-assigned IEs with unknown contents (128, 129, 133-136, 2936 * 149, 150, 155, 156, 173, 176, 178, 179, 219); for forward compatibility 2937 * it could also include some currently unused IDs. 2938 * 2939 * 2940 * In addition to these capabilities, hardware should support notifying the 2941 * host of changes in the beacon RSSI. This is relevant to implement roaming 2942 * when no traffic is flowing (when traffic is flowing we see the RSSI of 2943 * the received data packets). This can consist in notifying the host when 2944 * the RSSI changes significantly or when it drops below or rises above 2945 * configurable thresholds. In the future these thresholds will also be 2946 * configured by mac80211 (which gets them from userspace) to implement 2947 * them as the roaming algorithm requires. 2948 * 2949 * If the hardware cannot implement this, the driver should ask it to 2950 * periodically pass beacon frames to the host so that software can do the 2951 * signal strength threshold checking. 2952 */ 2953 2954 /** 2955 * DOC: Spatial multiplexing power save 2956 * 2957 * SMPS (Spatial multiplexing power save) is a mechanism to conserve 2958 * power in an 802.11n implementation. For details on the mechanism 2959 * and rationale, please refer to 802.11 (as amended by 802.11n-2009) 2960 * "11.2.3 SM power save". 2961 * 2962 * The mac80211 implementation is capable of sending action frames 2963 * to update the AP about the station's SMPS mode, and will instruct 2964 * the driver to enter the specific mode. It will also announce the 2965 * requested SMPS mode during the association handshake. Hardware 2966 * support for this feature is required, and can be indicated by 2967 * hardware flags. 2968 * 2969 * The default mode will be "automatic", which nl80211/cfg80211 2970 * defines to be dynamic SMPS in (regular) powersave, and SMPS 2971 * turned off otherwise. 2972 * 2973 * To support this feature, the driver must set the appropriate 2974 * hardware support flags, and handle the SMPS flag to the config() 2975 * operation. It will then with this mechanism be instructed to 2976 * enter the requested SMPS mode while associated to an HT AP. 2977 */ 2978 2979 /** 2980 * DOC: Frame filtering 2981 * 2982 * mac80211 requires to see many management frames for proper 2983 * operation, and users may want to see many more frames when 2984 * in monitor mode. However, for best CPU usage and power consumption, 2985 * having as few frames as possible percolate through the stack is 2986 * desirable. Hence, the hardware should filter as much as possible. 2987 * 2988 * To achieve this, mac80211 uses filter flags (see below) to tell 2989 * the driver's configure_filter() function which frames should be 2990 * passed to mac80211 and which should be filtered out. 2991 * 2992 * Before configure_filter() is invoked, the prepare_multicast() 2993 * callback is invoked with the parameters @mc_count and @mc_list 2994 * for the combined multicast address list of all virtual interfaces. 2995 * It's use is optional, and it returns a u64 that is passed to 2996 * configure_filter(). Additionally, configure_filter() has the 2997 * arguments @changed_flags telling which flags were changed and 2998 * @total_flags with the new flag states. 2999 * 3000 * If your device has no multicast address filters your driver will 3001 * need to check both the %FIF_ALLMULTI flag and the @mc_count 3002 * parameter to see whether multicast frames should be accepted 3003 * or dropped. 3004 * 3005 * All unsupported flags in @total_flags must be cleared. 3006 * Hardware does not support a flag if it is incapable of _passing_ 3007 * the frame to the stack. Otherwise the driver must ignore 3008 * the flag, but not clear it. 3009 * You must _only_ clear the flag (announce no support for the 3010 * flag to mac80211) if you are not able to pass the packet type 3011 * to the stack (so the hardware always filters it). 3012 * So for example, you should clear @FIF_CONTROL, if your hardware 3013 * always filters control frames. If your hardware always passes 3014 * control frames to the kernel and is incapable of filtering them, 3015 * you do _not_ clear the @FIF_CONTROL flag. 3016 * This rule applies to all other FIF flags as well. 3017 */ 3018 3019 /** 3020 * DOC: AP support for powersaving clients 3021 * 3022 * In order to implement AP and P2P GO modes, mac80211 has support for 3023 * client powersaving, both "legacy" PS (PS-Poll/null data) and uAPSD. 3024 * There currently is no support for sAPSD. 3025 * 3026 * There is one assumption that mac80211 makes, namely that a client 3027 * will not poll with PS-Poll and trigger with uAPSD at the same time. 3028 * Both are supported, and both can be used by the same client, but 3029 * they can't be used concurrently by the same client. This simplifies 3030 * the driver code. 3031 * 3032 * The first thing to keep in mind is that there is a flag for complete 3033 * driver implementation: %IEEE80211_HW_AP_LINK_PS. If this flag is set, 3034 * mac80211 expects the driver to handle most of the state machine for 3035 * powersaving clients and will ignore the PM bit in incoming frames. 3036 * Drivers then use ieee80211_sta_ps_transition() to inform mac80211 of 3037 * stations' powersave transitions. In this mode, mac80211 also doesn't 3038 * handle PS-Poll/uAPSD. 3039 * 3040 * In the mode without %IEEE80211_HW_AP_LINK_PS, mac80211 will check the 3041 * PM bit in incoming frames for client powersave transitions. When a 3042 * station goes to sleep, we will stop transmitting to it. There is, 3043 * however, a race condition: a station might go to sleep while there is 3044 * data buffered on hardware queues. If the device has support for this 3045 * it will reject frames, and the driver should give the frames back to 3046 * mac80211 with the %IEEE80211_TX_STAT_TX_FILTERED flag set which will 3047 * cause mac80211 to retry the frame when the station wakes up. The 3048 * driver is also notified of powersave transitions by calling its 3049 * @sta_notify callback. 3050 * 3051 * When the station is asleep, it has three choices: it can wake up, 3052 * it can PS-Poll, or it can possibly start a uAPSD service period. 3053 * Waking up is implemented by simply transmitting all buffered (and 3054 * filtered) frames to the station. This is the easiest case. When 3055 * the station sends a PS-Poll or a uAPSD trigger frame, mac80211 3056 * will inform the driver of this with the @allow_buffered_frames 3057 * callback; this callback is optional. mac80211 will then transmit 3058 * the frames as usual and set the %IEEE80211_TX_CTL_NO_PS_BUFFER 3059 * on each frame. The last frame in the service period (or the only 3060 * response to a PS-Poll) also has %IEEE80211_TX_STATUS_EOSP set to 3061 * indicate that it ends the service period; as this frame must have 3062 * TX status report it also sets %IEEE80211_TX_CTL_REQ_TX_STATUS. 3063 * When TX status is reported for this frame, the service period is 3064 * marked has having ended and a new one can be started by the peer. 3065 * 3066 * Additionally, non-bufferable MMPDUs can also be transmitted by 3067 * mac80211 with the %IEEE80211_TX_CTL_NO_PS_BUFFER set in them. 3068 * 3069 * Another race condition can happen on some devices like iwlwifi 3070 * when there are frames queued for the station and it wakes up 3071 * or polls; the frames that are already queued could end up being 3072 * transmitted first instead, causing reordering and/or wrong 3073 * processing of the EOSP. The cause is that allowing frames to be 3074 * transmitted to a certain station is out-of-band communication to 3075 * the device. To allow this problem to be solved, the driver can 3076 * call ieee80211_sta_block_awake() if frames are buffered when it 3077 * is notified that the station went to sleep. When all these frames 3078 * have been filtered (see above), it must call the function again 3079 * to indicate that the station is no longer blocked. 3080 * 3081 * If the driver buffers frames in the driver for aggregation in any 3082 * way, it must use the ieee80211_sta_set_buffered() call when it is 3083 * notified of the station going to sleep to inform mac80211 of any 3084 * TIDs that have frames buffered. Note that when a station wakes up 3085 * this information is reset (hence the requirement to call it when 3086 * informed of the station going to sleep). Then, when a service 3087 * period starts for any reason, @release_buffered_frames is called 3088 * with the number of frames to be released and which TIDs they are 3089 * to come from. In this case, the driver is responsible for setting 3090 * the EOSP (for uAPSD) and MORE_DATA bits in the released frames, 3091 * to help the @more_data parameter is passed to tell the driver if 3092 * there is more data on other TIDs -- the TIDs to release frames 3093 * from are ignored since mac80211 doesn't know how many frames the 3094 * buffers for those TIDs contain. 3095 * 3096 * If the driver also implement GO mode, where absence periods may 3097 * shorten service periods (or abort PS-Poll responses), it must 3098 * filter those response frames except in the case of frames that 3099 * are buffered in the driver -- those must remain buffered to avoid 3100 * reordering. Because it is possible that no frames are released 3101 * in this case, the driver must call ieee80211_sta_eosp() 3102 * to indicate to mac80211 that the service period ended anyway. 3103 * 3104 * Finally, if frames from multiple TIDs are released from mac80211 3105 * but the driver might reorder them, it must clear & set the flags 3106 * appropriately (only the last frame may have %IEEE80211_TX_STATUS_EOSP) 3107 * and also take care of the EOSP and MORE_DATA bits in the frame. 3108 * The driver may also use ieee80211_sta_eosp() in this case. 3109 * 3110 * Note that if the driver ever buffers frames other than QoS-data 3111 * frames, it must take care to never send a non-QoS-data frame as 3112 * the last frame in a service period, adding a QoS-nulldata frame 3113 * after a non-QoS-data frame if needed. 3114 */ 3115 3116 /** 3117 * DOC: HW queue control 3118 * 3119 * Before HW queue control was introduced, mac80211 only had a single static 3120 * assignment of per-interface AC software queues to hardware queues. This 3121 * was problematic for a few reasons: 3122 * 1) off-channel transmissions might get stuck behind other frames 3123 * 2) multiple virtual interfaces couldn't be handled correctly 3124 * 3) after-DTIM frames could get stuck behind other frames 3125 * 3126 * To solve this, hardware typically uses multiple different queues for all 3127 * the different usages, and this needs to be propagated into mac80211 so it 3128 * won't have the same problem with the software queues. 3129 * 3130 * Therefore, mac80211 now offers the %IEEE80211_HW_QUEUE_CONTROL capability 3131 * flag that tells it that the driver implements its own queue control. To do 3132 * so, the driver will set up the various queues in each &struct ieee80211_vif 3133 * and the offchannel queue in &struct ieee80211_hw. In response, mac80211 will 3134 * use those queue IDs in the hw_queue field of &struct ieee80211_tx_info and 3135 * if necessary will queue the frame on the right software queue that mirrors 3136 * the hardware queue. 3137 * Additionally, the driver has to then use these HW queue IDs for the queue 3138 * management functions (ieee80211_stop_queue() et al.) 3139 * 3140 * The driver is free to set up the queue mappings as needed, multiple virtual 3141 * interfaces may map to the same hardware queues if needed. The setup has to 3142 * happen during add_interface or change_interface callbacks. For example, a 3143 * driver supporting station+station and station+AP modes might decide to have 3144 * 10 hardware queues to handle different scenarios: 3145 * 3146 * 4 AC HW queues for 1st vif: 0, 1, 2, 3 3147 * 4 AC HW queues for 2nd vif: 4, 5, 6, 7 3148 * after-DTIM queue for AP: 8 3149 * off-channel queue: 9 3150 * 3151 * It would then set up the hardware like this: 3152 * hw.offchannel_tx_hw_queue = 9 3153 * 3154 * and the first virtual interface that is added as follows: 3155 * vif.hw_queue[IEEE80211_AC_VO] = 0 3156 * vif.hw_queue[IEEE80211_AC_VI] = 1 3157 * vif.hw_queue[IEEE80211_AC_BE] = 2 3158 * vif.hw_queue[IEEE80211_AC_BK] = 3 3159 * vif.cab_queue = 8 // if AP mode, otherwise %IEEE80211_INVAL_HW_QUEUE 3160 * and the second virtual interface with 4-7. 3161 * 3162 * If queue 6 gets full, for example, mac80211 would only stop the second 3163 * virtual interface's BE queue since virtual interface queues are per AC. 3164 * 3165 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE 3166 * whenever the queue is not used (i.e. the interface is not in AP mode) if the 3167 * queue could potentially be shared since mac80211 will look at cab_queue when 3168 * a queue is stopped/woken even if the interface is not in AP mode. 3169 */ 3170 3171 /** 3172 * enum ieee80211_filter_flags - hardware filter flags 3173 * 3174 * These flags determine what the filter in hardware should be 3175 * programmed to let through and what should not be passed to the 3176 * stack. It is always safe to pass more frames than requested, 3177 * but this has negative impact on power consumption. 3178 * 3179 * @FIF_ALLMULTI: pass all multicast frames, this is used if requested 3180 * by the user or if the hardware is not capable of filtering by 3181 * multicast address. 3182 * 3183 * @FIF_FCSFAIL: pass frames with failed FCS (but you need to set the 3184 * %RX_FLAG_FAILED_FCS_CRC for them) 3185 * 3186 * @FIF_PLCPFAIL: pass frames with failed PLCP CRC (but you need to set 3187 * the %RX_FLAG_FAILED_PLCP_CRC for them 3188 * 3189 * @FIF_BCN_PRBRESP_PROMISC: This flag is set during scanning to indicate 3190 * to the hardware that it should not filter beacons or probe responses 3191 * by BSSID. Filtering them can greatly reduce the amount of processing 3192 * mac80211 needs to do and the amount of CPU wakeups, so you should 3193 * honour this flag if possible. 3194 * 3195 * @FIF_CONTROL: pass control frames (except for PS Poll) addressed to this 3196 * station 3197 * 3198 * @FIF_OTHER_BSS: pass frames destined to other BSSes 3199 * 3200 * @FIF_PSPOLL: pass PS Poll frames 3201 * 3202 * @FIF_PROBE_REQ: pass probe request frames 3203 * 3204 * @FIF_MCAST_ACTION: pass multicast Action frames 3205 */ 3206 enum ieee80211_filter_flags { 3207 FIF_ALLMULTI = 1<<1, 3208 FIF_FCSFAIL = 1<<2, 3209 FIF_PLCPFAIL = 1<<3, 3210 FIF_BCN_PRBRESP_PROMISC = 1<<4, 3211 FIF_CONTROL = 1<<5, 3212 FIF_OTHER_BSS = 1<<6, 3213 FIF_PSPOLL = 1<<7, 3214 FIF_PROBE_REQ = 1<<8, 3215 FIF_MCAST_ACTION = 1<<9, 3216 }; 3217 3218 /** 3219 * enum ieee80211_ampdu_mlme_action - A-MPDU actions 3220 * 3221 * These flags are used with the ampdu_action() callback in 3222 * &struct ieee80211_ops to indicate which action is needed. 3223 * 3224 * Note that drivers MUST be able to deal with a TX aggregation 3225 * session being stopped even before they OK'ed starting it by 3226 * calling ieee80211_start_tx_ba_cb_irqsafe, because the peer 3227 * might receive the addBA frame and send a delBA right away! 3228 * 3229 * @IEEE80211_AMPDU_RX_START: start RX aggregation 3230 * @IEEE80211_AMPDU_RX_STOP: stop RX aggregation 3231 * @IEEE80211_AMPDU_TX_START: start TX aggregation, the driver must either 3232 * call ieee80211_start_tx_ba_cb_irqsafe() or 3233 * call ieee80211_start_tx_ba_cb_irqsafe() with status 3234 * %IEEE80211_AMPDU_TX_START_DELAY_ADDBA to delay addba after 3235 * ieee80211_start_tx_ba_cb_irqsafe is called, or just return the special 3236 * status %IEEE80211_AMPDU_TX_START_IMMEDIATE. 3237 * @IEEE80211_AMPDU_TX_OPERATIONAL: TX aggregation has become operational 3238 * @IEEE80211_AMPDU_TX_STOP_CONT: stop TX aggregation but continue transmitting 3239 * queued packets, now unaggregated. After all packets are transmitted the 3240 * driver has to call ieee80211_stop_tx_ba_cb_irqsafe(). 3241 * @IEEE80211_AMPDU_TX_STOP_FLUSH: stop TX aggregation and flush all packets, 3242 * called when the station is removed. There's no need or reason to call 3243 * ieee80211_stop_tx_ba_cb_irqsafe() in this case as mac80211 assumes the 3244 * session is gone and removes the station. 3245 * @IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: called when TX aggregation is stopped 3246 * but the driver hasn't called ieee80211_stop_tx_ba_cb_irqsafe() yet and 3247 * now the connection is dropped and the station will be removed. Drivers 3248 * should clean up and drop remaining packets when this is called. 3249 */ 3250 enum ieee80211_ampdu_mlme_action { 3251 IEEE80211_AMPDU_RX_START, 3252 IEEE80211_AMPDU_RX_STOP, 3253 IEEE80211_AMPDU_TX_START, 3254 IEEE80211_AMPDU_TX_STOP_CONT, 3255 IEEE80211_AMPDU_TX_STOP_FLUSH, 3256 IEEE80211_AMPDU_TX_STOP_FLUSH_CONT, 3257 IEEE80211_AMPDU_TX_OPERATIONAL, 3258 }; 3259 3260 #define IEEE80211_AMPDU_TX_START_IMMEDIATE 1 3261 #define IEEE80211_AMPDU_TX_START_DELAY_ADDBA 2 3262 3263 /** 3264 * struct ieee80211_ampdu_params - AMPDU action parameters 3265 * 3266 * @action: the ampdu action, value from %ieee80211_ampdu_mlme_action. 3267 * @sta: peer of this AMPDU session 3268 * @tid: tid of the BA session 3269 * @ssn: start sequence number of the session. TX/RX_STOP can pass 0. When 3270 * action is set to %IEEE80211_AMPDU_RX_START the driver passes back the 3271 * actual ssn value used to start the session and writes the value here. 3272 * @buf_size: reorder buffer size (number of subframes). Valid only when the 3273 * action is set to %IEEE80211_AMPDU_RX_START or 3274 * %IEEE80211_AMPDU_TX_OPERATIONAL 3275 * @amsdu: indicates the peer's ability to receive A-MSDU within A-MPDU. 3276 * valid when the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL 3277 * @timeout: BA session timeout. Valid only when the action is set to 3278 * %IEEE80211_AMPDU_RX_START 3279 */ 3280 struct ieee80211_ampdu_params { 3281 enum ieee80211_ampdu_mlme_action action; 3282 struct ieee80211_sta *sta; 3283 u16 tid; 3284 u16 ssn; 3285 u16 buf_size; 3286 bool amsdu; 3287 u16 timeout; 3288 }; 3289 3290 /** 3291 * enum ieee80211_frame_release_type - frame release reason 3292 * @IEEE80211_FRAME_RELEASE_PSPOLL: frame released for PS-Poll 3293 * @IEEE80211_FRAME_RELEASE_UAPSD: frame(s) released due to 3294 * frame received on trigger-enabled AC 3295 */ 3296 enum ieee80211_frame_release_type { 3297 IEEE80211_FRAME_RELEASE_PSPOLL, 3298 IEEE80211_FRAME_RELEASE_UAPSD, 3299 }; 3300 3301 /** 3302 * enum ieee80211_rate_control_changed - flags to indicate what changed 3303 * 3304 * @IEEE80211_RC_BW_CHANGED: The bandwidth that can be used to transmit 3305 * to this station changed. The actual bandwidth is in the station 3306 * information -- for HT20/40 the IEEE80211_HT_CAP_SUP_WIDTH_20_40 3307 * flag changes, for HT and VHT the bandwidth field changes. 3308 * @IEEE80211_RC_SMPS_CHANGED: The SMPS state of the station changed. 3309 * @IEEE80211_RC_SUPP_RATES_CHANGED: The supported rate set of this peer 3310 * changed (in IBSS mode) due to discovering more information about 3311 * the peer. 3312 * @IEEE80211_RC_NSS_CHANGED: N_SS (number of spatial streams) was changed 3313 * by the peer 3314 */ 3315 enum ieee80211_rate_control_changed { 3316 IEEE80211_RC_BW_CHANGED = BIT(0), 3317 IEEE80211_RC_SMPS_CHANGED = BIT(1), 3318 IEEE80211_RC_SUPP_RATES_CHANGED = BIT(2), 3319 IEEE80211_RC_NSS_CHANGED = BIT(3), 3320 }; 3321 3322 /** 3323 * enum ieee80211_roc_type - remain on channel type 3324 * 3325 * With the support for multi channel contexts and multi channel operations, 3326 * remain on channel operations might be limited/deferred/aborted by other 3327 * flows/operations which have higher priority (and vice versa). 3328 * Specifying the ROC type can be used by devices to prioritize the ROC 3329 * operations compared to other operations/flows. 3330 * 3331 * @IEEE80211_ROC_TYPE_NORMAL: There are no special requirements for this ROC. 3332 * @IEEE80211_ROC_TYPE_MGMT_TX: The remain on channel request is required 3333 * for sending management frames offchannel. 3334 */ 3335 enum ieee80211_roc_type { 3336 IEEE80211_ROC_TYPE_NORMAL = 0, 3337 IEEE80211_ROC_TYPE_MGMT_TX, 3338 }; 3339 3340 /** 3341 * enum ieee80211_reconfig_type - reconfig type 3342 * 3343 * This enum is used by the reconfig_complete() callback to indicate what 3344 * reconfiguration type was completed. 3345 * 3346 * @IEEE80211_RECONFIG_TYPE_RESTART: hw restart type 3347 * (also due to resume() callback returning 1) 3348 * @IEEE80211_RECONFIG_TYPE_SUSPEND: suspend type (regardless 3349 * of wowlan configuration) 3350 */ 3351 enum ieee80211_reconfig_type { 3352 IEEE80211_RECONFIG_TYPE_RESTART, 3353 IEEE80211_RECONFIG_TYPE_SUSPEND, 3354 }; 3355 3356 /** 3357 * struct ieee80211_prep_tx_info - prepare TX information 3358 * @duration: if non-zero, hint about the required duration, 3359 * only used with the mgd_prepare_tx() method. 3360 * @subtype: frame subtype (auth, (re)assoc, deauth, disassoc) 3361 * @success: whether the frame exchange was successful, only 3362 * used with the mgd_complete_tx() method, and then only 3363 * valid for auth and (re)assoc. 3364 */ 3365 struct ieee80211_prep_tx_info { 3366 u16 duration; 3367 u16 subtype; 3368 u8 success:1; 3369 }; 3370 3371 /** 3372 * struct ieee80211_ops - callbacks from mac80211 to the driver 3373 * 3374 * This structure contains various callbacks that the driver may 3375 * handle or, in some cases, must handle, for example to configure 3376 * the hardware to a new channel or to transmit a frame. 3377 * 3378 * @tx: Handler that 802.11 module calls for each transmitted frame. 3379 * skb contains the buffer starting from the IEEE 802.11 header. 3380 * The low-level driver should send the frame out based on 3381 * configuration in the TX control data. This handler should, 3382 * preferably, never fail and stop queues appropriately. 3383 * Must be atomic. 3384 * 3385 * @start: Called before the first netdevice attached to the hardware 3386 * is enabled. This should turn on the hardware and must turn on 3387 * frame reception (for possibly enabled monitor interfaces.) 3388 * Returns negative error codes, these may be seen in userspace, 3389 * or zero. 3390 * When the device is started it should not have a MAC address 3391 * to avoid acknowledging frames before a non-monitor device 3392 * is added. 3393 * Must be implemented and can sleep. 3394 * 3395 * @stop: Called after last netdevice attached to the hardware 3396 * is disabled. This should turn off the hardware (at least 3397 * it must turn off frame reception.) 3398 * May be called right after add_interface if that rejects 3399 * an interface. If you added any work onto the mac80211 workqueue 3400 * you should ensure to cancel it on this callback. 3401 * Must be implemented and can sleep. 3402 * 3403 * @suspend: Suspend the device; mac80211 itself will quiesce before and 3404 * stop transmitting and doing any other configuration, and then 3405 * ask the device to suspend. This is only invoked when WoWLAN is 3406 * configured, otherwise the device is deconfigured completely and 3407 * reconfigured at resume time. 3408 * The driver may also impose special conditions under which it 3409 * wants to use the "normal" suspend (deconfigure), say if it only 3410 * supports WoWLAN when the device is associated. In this case, it 3411 * must return 1 from this function. 3412 * 3413 * @resume: If WoWLAN was configured, this indicates that mac80211 is 3414 * now resuming its operation, after this the device must be fully 3415 * functional again. If this returns an error, the only way out is 3416 * to also unregister the device. If it returns 1, then mac80211 3417 * will also go through the regular complete restart on resume. 3418 * 3419 * @set_wakeup: Enable or disable wakeup when WoWLAN configuration is 3420 * modified. The reason is that device_set_wakeup_enable() is 3421 * supposed to be called when the configuration changes, not only 3422 * in suspend(). 3423 * 3424 * @add_interface: Called when a netdevice attached to the hardware is 3425 * enabled. Because it is not called for monitor mode devices, @start 3426 * and @stop must be implemented. 3427 * The driver should perform any initialization it needs before 3428 * the device can be enabled. The initial configuration for the 3429 * interface is given in the conf parameter. 3430 * The callback may refuse to add an interface by returning a 3431 * negative error code (which will be seen in userspace.) 3432 * Must be implemented and can sleep. 3433 * 3434 * @change_interface: Called when a netdevice changes type. This callback 3435 * is optional, but only if it is supported can interface types be 3436 * switched while the interface is UP. The callback may sleep. 3437 * Note that while an interface is being switched, it will not be 3438 * found by the interface iteration callbacks. 3439 * 3440 * @remove_interface: Notifies a driver that an interface is going down. 3441 * The @stop callback is called after this if it is the last interface 3442 * and no monitor interfaces are present. 3443 * When all interfaces are removed, the MAC address in the hardware 3444 * must be cleared so the device no longer acknowledges packets, 3445 * the mac_addr member of the conf structure is, however, set to the 3446 * MAC address of the device going away. 3447 * Hence, this callback must be implemented. It can sleep. 3448 * 3449 * @config: Handler for configuration requests. IEEE 802.11 code calls this 3450 * function to change hardware configuration, e.g., channel. 3451 * This function should never fail but returns a negative error code 3452 * if it does. The callback can sleep. 3453 * 3454 * @bss_info_changed: Handler for configuration requests related to BSS 3455 * parameters that may vary during BSS's lifespan, and may affect low 3456 * level driver (e.g. assoc/disassoc status, erp parameters). 3457 * This function should not be used if no BSS has been set, unless 3458 * for association indication. The @changed parameter indicates which 3459 * of the bss parameters has changed when a call is made. The callback 3460 * can sleep. 3461 * 3462 * @prepare_multicast: Prepare for multicast filter configuration. 3463 * This callback is optional, and its return value is passed 3464 * to configure_filter(). This callback must be atomic. 3465 * 3466 * @configure_filter: Configure the device's RX filter. 3467 * See the section "Frame filtering" for more information. 3468 * This callback must be implemented and can sleep. 3469 * 3470 * @config_iface_filter: Configure the interface's RX filter. 3471 * This callback is optional and is used to configure which frames 3472 * should be passed to mac80211. The filter_flags is the combination 3473 * of FIF_* flags. The changed_flags is a bit mask that indicates 3474 * which flags are changed. 3475 * This callback can sleep. 3476 * 3477 * @set_tim: Set TIM bit. mac80211 calls this function when a TIM bit 3478 * must be set or cleared for a given STA. Must be atomic. 3479 * 3480 * @set_key: See the section "Hardware crypto acceleration" 3481 * This callback is only called between add_interface and 3482 * remove_interface calls, i.e. while the given virtual interface 3483 * is enabled. 3484 * Returns a negative error code if the key can't be added. 3485 * The callback can sleep. 3486 * 3487 * @update_tkip_key: See the section "Hardware crypto acceleration" 3488 * This callback will be called in the context of Rx. Called for drivers 3489 * which set IEEE80211_KEY_FLAG_TKIP_REQ_RX_P1_KEY. 3490 * The callback must be atomic. 3491 * 3492 * @set_rekey_data: If the device supports GTK rekeying, for example while the 3493 * host is suspended, it can assign this callback to retrieve the data 3494 * necessary to do GTK rekeying, this is the KEK, KCK and replay counter. 3495 * After rekeying was done it should (for example during resume) notify 3496 * userspace of the new replay counter using ieee80211_gtk_rekey_notify(). 3497 * 3498 * @set_default_unicast_key: Set the default (unicast) key index, useful for 3499 * WEP when the device sends data packets autonomously, e.g. for ARP 3500 * offloading. The index can be 0-3, or -1 for unsetting it. 3501 * 3502 * @hw_scan: Ask the hardware to service the scan request, no need to start 3503 * the scan state machine in stack. The scan must honour the channel 3504 * configuration done by the regulatory agent in the wiphy's 3505 * registered bands. The hardware (or the driver) needs to make sure 3506 * that power save is disabled. 3507 * The @req ie/ie_len members are rewritten by mac80211 to contain the 3508 * entire IEs after the SSID, so that drivers need not look at these 3509 * at all but just send them after the SSID -- mac80211 includes the 3510 * (extended) supported rates and HT information (where applicable). 3511 * When the scan finishes, ieee80211_scan_completed() must be called; 3512 * note that it also must be called when the scan cannot finish due to 3513 * any error unless this callback returned a negative error code. 3514 * This callback is also allowed to return the special return value 1, 3515 * this indicates that hardware scan isn't desirable right now and a 3516 * software scan should be done instead. A driver wishing to use this 3517 * capability must ensure its (hardware) scan capabilities aren't 3518 * advertised as more capable than mac80211's software scan is. 3519 * The callback can sleep. 3520 * 3521 * @cancel_hw_scan: Ask the low-level tp cancel the active hw scan. 3522 * The driver should ask the hardware to cancel the scan (if possible), 3523 * but the scan will be completed only after the driver will call 3524 * ieee80211_scan_completed(). 3525 * This callback is needed for wowlan, to prevent enqueueing a new 3526 * scan_work after the low-level driver was already suspended. 3527 * The callback can sleep. 3528 * 3529 * @sched_scan_start: Ask the hardware to start scanning repeatedly at 3530 * specific intervals. The driver must call the 3531 * ieee80211_sched_scan_results() function whenever it finds results. 3532 * This process will continue until sched_scan_stop is called. 3533 * 3534 * @sched_scan_stop: Tell the hardware to stop an ongoing scheduled scan. 3535 * In this case, ieee80211_sched_scan_stopped() must not be called. 3536 * 3537 * @sw_scan_start: Notifier function that is called just before a software scan 3538 * is started. Can be NULL, if the driver doesn't need this notification. 3539 * The mac_addr parameter allows supporting NL80211_SCAN_FLAG_RANDOM_ADDR, 3540 * the driver may set the NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR flag if it 3541 * can use this parameter. The callback can sleep. 3542 * 3543 * @sw_scan_complete: Notifier function that is called just after a 3544 * software scan finished. Can be NULL, if the driver doesn't need 3545 * this notification. 3546 * The callback can sleep. 3547 * 3548 * @get_stats: Return low-level statistics. 3549 * Returns zero if statistics are available. 3550 * The callback can sleep. 3551 * 3552 * @get_key_seq: If your device implements encryption in hardware and does 3553 * IV/PN assignment then this callback should be provided to read the 3554 * IV/PN for the given key from hardware. 3555 * The callback must be atomic. 3556 * 3557 * @set_frag_threshold: Configuration of fragmentation threshold. Assign this 3558 * if the device does fragmentation by itself. Note that to prevent the 3559 * stack from doing fragmentation IEEE80211_HW_SUPPORTS_TX_FRAG 3560 * should be set as well. 3561 * The callback can sleep. 3562 * 3563 * @set_rts_threshold: Configuration of RTS threshold (if device needs it) 3564 * The callback can sleep. 3565 * 3566 * @sta_add: Notifies low level driver about addition of an associated station, 3567 * AP, IBSS/WDS/mesh peer etc. This callback can sleep. 3568 * 3569 * @sta_remove: Notifies low level driver about removal of an associated 3570 * station, AP, IBSS/WDS/mesh peer etc. Note that after the callback 3571 * returns it isn't safe to use the pointer, not even RCU protected; 3572 * no RCU grace period is guaranteed between returning here and freeing 3573 * the station. See @sta_pre_rcu_remove if needed. 3574 * This callback can sleep. 3575 * 3576 * @sta_add_debugfs: Drivers can use this callback to add debugfs files 3577 * when a station is added to mac80211's station list. This callback 3578 * should be within a CONFIG_MAC80211_DEBUGFS conditional. This 3579 * callback can sleep. 3580 * 3581 * @sta_notify: Notifies low level driver about power state transition of an 3582 * associated station, AP, IBSS/WDS/mesh peer etc. For a VIF operating 3583 * in AP mode, this callback will not be called when the flag 3584 * %IEEE80211_HW_AP_LINK_PS is set. Must be atomic. 3585 * 3586 * @sta_set_txpwr: Configure the station tx power. This callback set the tx 3587 * power for the station. 3588 * This callback can sleep. 3589 * 3590 * @sta_state: Notifies low level driver about state transition of a 3591 * station (which can be the AP, a client, IBSS/WDS/mesh peer etc.) 3592 * This callback is mutually exclusive with @sta_add/@sta_remove. 3593 * It must not fail for down transitions but may fail for transitions 3594 * up the list of states. Also note that after the callback returns it 3595 * isn't safe to use the pointer, not even RCU protected - no RCU grace 3596 * period is guaranteed between returning here and freeing the station. 3597 * See @sta_pre_rcu_remove if needed. 3598 * The callback can sleep. 3599 * 3600 * @sta_pre_rcu_remove: Notify driver about station removal before RCU 3601 * synchronisation. This is useful if a driver needs to have station 3602 * pointers protected using RCU, it can then use this call to clear 3603 * the pointers instead of waiting for an RCU grace period to elapse 3604 * in @sta_state. 3605 * The callback can sleep. 3606 * 3607 * @sta_rc_update: Notifies the driver of changes to the bitrates that can be 3608 * used to transmit to the station. The changes are advertised with bits 3609 * from &enum ieee80211_rate_control_changed and the values are reflected 3610 * in the station data. This callback should only be used when the driver 3611 * uses hardware rate control (%IEEE80211_HW_HAS_RATE_CONTROL) since 3612 * otherwise the rate control algorithm is notified directly. 3613 * Must be atomic. 3614 * @sta_rate_tbl_update: Notifies the driver that the rate table changed. This 3615 * is only used if the configured rate control algorithm actually uses 3616 * the new rate table API, and is therefore optional. Must be atomic. 3617 * 3618 * @sta_statistics: Get statistics for this station. For example with beacon 3619 * filtering, the statistics kept by mac80211 might not be accurate, so 3620 * let the driver pre-fill the statistics. The driver can fill most of 3621 * the values (indicating which by setting the filled bitmap), but not 3622 * all of them make sense - see the source for which ones are possible. 3623 * Statistics that the driver doesn't fill will be filled by mac80211. 3624 * The callback can sleep. 3625 * 3626 * @conf_tx: Configure TX queue parameters (EDCF (aifs, cw_min, cw_max), 3627 * bursting) for a hardware TX queue. 3628 * Returns a negative error code on failure. 3629 * The callback can sleep. 3630 * 3631 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently, 3632 * this is only used for IBSS mode BSSID merging and debugging. Is not a 3633 * required function. 3634 * The callback can sleep. 3635 * 3636 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware. 3637 * Currently, this is only used for IBSS mode debugging. Is not a 3638 * required function. 3639 * The callback can sleep. 3640 * 3641 * @offset_tsf: Offset the TSF timer by the specified value in the 3642 * firmware/hardware. Preferred to set_tsf as it avoids delay between 3643 * calling set_tsf() and hardware getting programmed, which will show up 3644 * as TSF delay. Is not a required function. 3645 * The callback can sleep. 3646 * 3647 * @reset_tsf: Reset the TSF timer and allow firmware/hardware to synchronize 3648 * with other STAs in the IBSS. This is only used in IBSS mode. This 3649 * function is optional if the firmware/hardware takes full care of 3650 * TSF synchronization. 3651 * The callback can sleep. 3652 * 3653 * @tx_last_beacon: Determine whether the last IBSS beacon was sent by us. 3654 * This is needed only for IBSS mode and the result of this function is 3655 * used to determine whether to reply to Probe Requests. 3656 * Returns non-zero if this device sent the last beacon. 3657 * The callback can sleep. 3658 * 3659 * @get_survey: Return per-channel survey information 3660 * 3661 * @rfkill_poll: Poll rfkill hardware state. If you need this, you also 3662 * need to set wiphy->rfkill_poll to %true before registration, 3663 * and need to call wiphy_rfkill_set_hw_state() in the callback. 3664 * The callback can sleep. 3665 * 3666 * @set_coverage_class: Set slot time for given coverage class as specified 3667 * in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout 3668 * accordingly; coverage class equals to -1 to enable ACK timeout 3669 * estimation algorithm (dynack). To disable dynack set valid value for 3670 * coverage class. This callback is not required and may sleep. 3671 * 3672 * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may 3673 * be %NULL. The callback can sleep. 3674 * @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep. 3675 * 3676 * @flush: Flush all pending frames from the hardware queue, making sure 3677 * that the hardware queues are empty. The @queues parameter is a bitmap 3678 * of queues to flush, which is useful if different virtual interfaces 3679 * use different hardware queues; it may also indicate all queues. 3680 * If the parameter @drop is set to %true, pending frames may be dropped. 3681 * Note that vif can be NULL. 3682 * The callback can sleep. 3683 * 3684 * @channel_switch: Drivers that need (or want) to offload the channel 3685 * switch operation for CSAs received from the AP may implement this 3686 * callback. They must then call ieee80211_chswitch_done() to indicate 3687 * completion of the channel switch. 3688 * 3689 * @set_antenna: Set antenna configuration (tx_ant, rx_ant) on the device. 3690 * Parameters are bitmaps of allowed antennas to use for TX/RX. Drivers may 3691 * reject TX/RX mask combinations they cannot support by returning -EINVAL 3692 * (also see nl80211.h @NL80211_ATTR_WIPHY_ANTENNA_TX). 3693 * 3694 * @get_antenna: Get current antenna configuration from device (tx_ant, rx_ant). 3695 * 3696 * @remain_on_channel: Starts an off-channel period on the given channel, must 3697 * call back to ieee80211_ready_on_channel() when on that channel. Note 3698 * that normal channel traffic is not stopped as this is intended for hw 3699 * offload. Frames to transmit on the off-channel channel are transmitted 3700 * normally except for the %IEEE80211_TX_CTL_TX_OFFCHAN flag. When the 3701 * duration (which will always be non-zero) expires, the driver must call 3702 * ieee80211_remain_on_channel_expired(). 3703 * Note that this callback may be called while the device is in IDLE and 3704 * must be accepted in this case. 3705 * This callback may sleep. 3706 * @cancel_remain_on_channel: Requests that an ongoing off-channel period is 3707 * aborted before it expires. This callback may sleep. 3708 * 3709 * @set_ringparam: Set tx and rx ring sizes. 3710 * 3711 * @get_ringparam: Get tx and rx ring current and maximum sizes. 3712 * 3713 * @tx_frames_pending: Check if there is any pending frame in the hardware 3714 * queues before entering power save. 3715 * 3716 * @set_bitrate_mask: Set a mask of rates to be used for rate control selection 3717 * when transmitting a frame. Currently only legacy rates are handled. 3718 * The callback can sleep. 3719 * @event_callback: Notify driver about any event in mac80211. See 3720 * &enum ieee80211_event_type for the different types. 3721 * The callback must be atomic. 3722 * 3723 * @release_buffered_frames: Release buffered frames according to the given 3724 * parameters. In the case where the driver buffers some frames for 3725 * sleeping stations mac80211 will use this callback to tell the driver 3726 * to release some frames, either for PS-poll or uAPSD. 3727 * Note that if the @more_data parameter is %false the driver must check 3728 * if there are more frames on the given TIDs, and if there are more than 3729 * the frames being released then it must still set the more-data bit in 3730 * the frame. If the @more_data parameter is %true, then of course the 3731 * more-data bit must always be set. 3732 * The @tids parameter tells the driver which TIDs to release frames 3733 * from, for PS-poll it will always have only a single bit set. 3734 * In the case this is used for a PS-poll initiated release, the 3735 * @num_frames parameter will always be 1 so code can be shared. In 3736 * this case the driver must also set %IEEE80211_TX_STATUS_EOSP flag 3737 * on the TX status (and must report TX status) so that the PS-poll 3738 * period is properly ended. This is used to avoid sending multiple 3739 * responses for a retried PS-poll frame. 3740 * In the case this is used for uAPSD, the @num_frames parameter may be 3741 * bigger than one, but the driver may send fewer frames (it must send 3742 * at least one, however). In this case it is also responsible for 3743 * setting the EOSP flag in the QoS header of the frames. Also, when the 3744 * service period ends, the driver must set %IEEE80211_TX_STATUS_EOSP 3745 * on the last frame in the SP. Alternatively, it may call the function 3746 * ieee80211_sta_eosp() to inform mac80211 of the end of the SP. 3747 * This callback must be atomic. 3748 * @allow_buffered_frames: Prepare device to allow the given number of frames 3749 * to go out to the given station. The frames will be sent by mac80211 3750 * via the usual TX path after this call. The TX information for frames 3751 * released will also have the %IEEE80211_TX_CTL_NO_PS_BUFFER flag set 3752 * and the last one will also have %IEEE80211_TX_STATUS_EOSP set. In case 3753 * frames from multiple TIDs are released and the driver might reorder 3754 * them between the TIDs, it must set the %IEEE80211_TX_STATUS_EOSP flag 3755 * on the last frame and clear it on all others and also handle the EOSP 3756 * bit in the QoS header correctly. Alternatively, it can also call the 3757 * ieee80211_sta_eosp() function. 3758 * The @tids parameter is a bitmap and tells the driver which TIDs the 3759 * frames will be on; it will at most have two bits set. 3760 * This callback must be atomic. 3761 * 3762 * @get_et_sset_count: Ethtool API to get string-set count. 3763 * 3764 * @get_et_stats: Ethtool API to get a set of u64 stats. 3765 * 3766 * @get_et_strings: Ethtool API to get a set of strings to describe stats 3767 * and perhaps other supported types of ethtool data-sets. 3768 * 3769 * @mgd_prepare_tx: Prepare for transmitting a management frame for association 3770 * before associated. In multi-channel scenarios, a virtual interface is 3771 * bound to a channel before it is associated, but as it isn't associated 3772 * yet it need not necessarily be given airtime, in particular since any 3773 * transmission to a P2P GO needs to be synchronized against the GO's 3774 * powersave state. mac80211 will call this function before transmitting a 3775 * management frame prior to having successfully associated to allow the 3776 * driver to give it channel time for the transmission, to get a response 3777 * and to be able to synchronize with the GO. 3778 * For drivers that set %IEEE80211_HW_DEAUTH_NEED_MGD_TX_PREP, mac80211 3779 * would also call this function before transmitting a deauthentication 3780 * frame in case that no beacon was heard from the AP/P2P GO. 3781 * The callback will be called before each transmission and upon return 3782 * mac80211 will transmit the frame right away. 3783 * Additional information is passed in the &struct ieee80211_prep_tx_info 3784 * data. If duration there is greater than zero, mac80211 hints to the 3785 * driver the duration for which the operation is requested. 3786 * The callback is optional and can (should!) sleep. 3787 * @mgd_complete_tx: Notify the driver that the response frame for a previously 3788 * transmitted frame announced with @mgd_prepare_tx was received, the data 3789 * is filled similarly to @mgd_prepare_tx though the duration is not used. 3790 * 3791 * @mgd_protect_tdls_discover: Protect a TDLS discovery session. After sending 3792 * a TDLS discovery-request, we expect a reply to arrive on the AP's 3793 * channel. We must stay on the channel (no PSM, scan, etc.), since a TDLS 3794 * setup-response is a direct packet not buffered by the AP. 3795 * mac80211 will call this function just before the transmission of a TDLS 3796 * discovery-request. The recommended period of protection is at least 3797 * 2 * (DTIM period). 3798 * The callback is optional and can sleep. 3799 * 3800 * @add_chanctx: Notifies device driver about new channel context creation. 3801 * This callback may sleep. 3802 * @remove_chanctx: Notifies device driver about channel context destruction. 3803 * This callback may sleep. 3804 * @change_chanctx: Notifies device driver about channel context changes that 3805 * may happen when combining different virtual interfaces on the same 3806 * channel context with different settings 3807 * This callback may sleep. 3808 * @assign_vif_chanctx: Notifies device driver about channel context being bound 3809 * to vif. Possible use is for hw queue remapping. 3810 * This callback may sleep. 3811 * @unassign_vif_chanctx: Notifies device driver about channel context being 3812 * unbound from vif. 3813 * This callback may sleep. 3814 * @switch_vif_chanctx: switch a number of vifs from one chanctx to 3815 * another, as specified in the list of 3816 * @ieee80211_vif_chanctx_switch passed to the driver, according 3817 * to the mode defined in &ieee80211_chanctx_switch_mode. 3818 * This callback may sleep. 3819 * 3820 * @start_ap: Start operation on the AP interface, this is called after all the 3821 * information in bss_conf is set and beacon can be retrieved. A channel 3822 * context is bound before this is called. Note that if the driver uses 3823 * software scan or ROC, this (and @stop_ap) isn't called when the AP is 3824 * just "paused" for scanning/ROC, which is indicated by the beacon being 3825 * disabled/enabled via @bss_info_changed. 3826 * @stop_ap: Stop operation on the AP interface. 3827 * 3828 * @reconfig_complete: Called after a call to ieee80211_restart_hw() and 3829 * during resume, when the reconfiguration has completed. 3830 * This can help the driver implement the reconfiguration step (and 3831 * indicate mac80211 is ready to receive frames). 3832 * This callback may sleep. 3833 * 3834 * @ipv6_addr_change: IPv6 address assignment on the given interface changed. 3835 * Currently, this is only called for managed or P2P client interfaces. 3836 * This callback is optional; it must not sleep. 3837 * 3838 * @channel_switch_beacon: Starts a channel switch to a new channel. 3839 * Beacons are modified to include CSA or ECSA IEs before calling this 3840 * function. The corresponding count fields in these IEs must be 3841 * decremented, and when they reach 1 the driver must call 3842 * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get() 3843 * get the csa counter decremented by mac80211, but must check if it is 3844 * 1 using ieee80211_beacon_counter_is_complete() after the beacon has been 3845 * transmitted and then call ieee80211_csa_finish(). 3846 * If the CSA count starts as zero or 1, this function will not be called, 3847 * since there won't be any time to beacon before the switch anyway. 3848 * @pre_channel_switch: This is an optional callback that is called 3849 * before a channel switch procedure is started (ie. when a STA 3850 * gets a CSA or a userspace initiated channel-switch), allowing 3851 * the driver to prepare for the channel switch. 3852 * @post_channel_switch: This is an optional callback that is called 3853 * after a channel switch procedure is completed, allowing the 3854 * driver to go back to a normal configuration. 3855 * @abort_channel_switch: This is an optional callback that is called 3856 * when channel switch procedure was completed, allowing the 3857 * driver to go back to a normal configuration. 3858 * @channel_switch_rx_beacon: This is an optional callback that is called 3859 * when channel switch procedure is in progress and additional beacon with 3860 * CSA IE was received, allowing driver to track changes in count. 3861 * @join_ibss: Join an IBSS (on an IBSS interface); this is called after all 3862 * information in bss_conf is set up and the beacon can be retrieved. A 3863 * channel context is bound before this is called. 3864 * @leave_ibss: Leave the IBSS again. 3865 * 3866 * @get_expected_throughput: extract the expected throughput towards the 3867 * specified station. The returned value is expressed in Kbps. It returns 0 3868 * if the RC algorithm does not have proper data to provide. 3869 * 3870 * @get_txpower: get current maximum tx power (in dBm) based on configuration 3871 * and hardware limits. 3872 * 3873 * @tdls_channel_switch: Start channel-switching with a TDLS peer. The driver 3874 * is responsible for continually initiating channel-switching operations 3875 * and returning to the base channel for communication with the AP. The 3876 * driver receives a channel-switch request template and the location of 3877 * the switch-timing IE within the template as part of the invocation. 3878 * The template is valid only within the call, and the driver can 3879 * optionally copy the skb for further re-use. 3880 * @tdls_cancel_channel_switch: Stop channel-switching with a TDLS peer. Both 3881 * peers must be on the base channel when the call completes. 3882 * @tdls_recv_channel_switch: a TDLS channel-switch related frame (request or 3883 * response) has been received from a remote peer. The driver gets 3884 * parameters parsed from the incoming frame and may use them to continue 3885 * an ongoing channel-switch operation. In addition, a channel-switch 3886 * response template is provided, together with the location of the 3887 * switch-timing IE within the template. The skb can only be used within 3888 * the function call. 3889 * 3890 * @wake_tx_queue: Called when new packets have been added to the queue. 3891 * @sync_rx_queues: Process all pending frames in RSS queues. This is a 3892 * synchronization which is needed in case driver has in its RSS queues 3893 * pending frames that were received prior to the control path action 3894 * currently taken (e.g. disassociation) but are not processed yet. 3895 * 3896 * @start_nan: join an existing NAN cluster, or create a new one. 3897 * @stop_nan: leave the NAN cluster. 3898 * @nan_change_conf: change NAN configuration. The data in cfg80211_nan_conf 3899 * contains full new configuration and changes specify which parameters 3900 * are changed with respect to the last NAN config. 3901 * The driver gets both full configuration and the changed parameters since 3902 * some devices may need the full configuration while others need only the 3903 * changed parameters. 3904 * @add_nan_func: Add a NAN function. Returns 0 on success. The data in 3905 * cfg80211_nan_func must not be referenced outside the scope of 3906 * this call. 3907 * @del_nan_func: Remove a NAN function. The driver must call 3908 * ieee80211_nan_func_terminated() with 3909 * NL80211_NAN_FUNC_TERM_REASON_USER_REQUEST reason code upon removal. 3910 * @can_aggregate_in_amsdu: Called in order to determine if HW supports 3911 * aggregating two specific frames in the same A-MSDU. The relation 3912 * between the skbs should be symmetric and transitive. Note that while 3913 * skb is always a real frame, head may or may not be an A-MSDU. 3914 * @get_ftm_responder_stats: Retrieve FTM responder statistics, if available. 3915 * Statistics should be cumulative, currently no way to reset is provided. 3916 * 3917 * @start_pmsr: start peer measurement (e.g. FTM) (this call can sleep) 3918 * @abort_pmsr: abort peer measurement (this call can sleep) 3919 * @set_tid_config: Apply TID specific configurations. This callback may sleep. 3920 * @reset_tid_config: Reset TID specific configuration for the peer. 3921 * This callback may sleep. 3922 * @update_vif_offload: Update virtual interface offload flags 3923 * This callback may sleep. 3924 * @sta_set_4addr: Called to notify the driver when a station starts/stops using 3925 * 4-address mode 3926 * @set_sar_specs: Update the SAR (TX power) settings. 3927 * @sta_set_decap_offload: Called to notify the driver when a station is allowed 3928 * to use rx decapsulation offload 3929 * @add_twt_setup: Update hw with TWT agreement parameters received from the peer. 3930 * This callback allows the hw to check if requested parameters 3931 * are supported and if there is enough room for a new agreement. 3932 * The hw is expected to set agreement result in the req_type field of 3933 * twt structure. 3934 * @twt_teardown_request: Update the hw with TWT teardown request received 3935 * from the peer. 3936 */ 3937 struct ieee80211_ops { 3938 void (*tx)(struct ieee80211_hw *hw, 3939 struct ieee80211_tx_control *control, 3940 struct sk_buff *skb); 3941 int (*start)(struct ieee80211_hw *hw); 3942 void (*stop)(struct ieee80211_hw *hw); 3943 #ifdef CONFIG_PM 3944 int (*suspend)(struct ieee80211_hw *hw, struct cfg80211_wowlan *wowlan); 3945 int (*resume)(struct ieee80211_hw *hw); 3946 void (*set_wakeup)(struct ieee80211_hw *hw, bool enabled); 3947 #endif 3948 int (*add_interface)(struct ieee80211_hw *hw, 3949 struct ieee80211_vif *vif); 3950 int (*change_interface)(struct ieee80211_hw *hw, 3951 struct ieee80211_vif *vif, 3952 enum nl80211_iftype new_type, bool p2p); 3953 void (*remove_interface)(struct ieee80211_hw *hw, 3954 struct ieee80211_vif *vif); 3955 int (*config)(struct ieee80211_hw *hw, u32 changed); 3956 void (*bss_info_changed)(struct ieee80211_hw *hw, 3957 struct ieee80211_vif *vif, 3958 struct ieee80211_bss_conf *info, 3959 u32 changed); 3960 3961 int (*start_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 3962 void (*stop_ap)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 3963 3964 u64 (*prepare_multicast)(struct ieee80211_hw *hw, 3965 struct netdev_hw_addr_list *mc_list); 3966 void (*configure_filter)(struct ieee80211_hw *hw, 3967 unsigned int changed_flags, 3968 unsigned int *total_flags, 3969 u64 multicast); 3970 void (*config_iface_filter)(struct ieee80211_hw *hw, 3971 struct ieee80211_vif *vif, 3972 unsigned int filter_flags, 3973 unsigned int changed_flags); 3974 int (*set_tim)(struct ieee80211_hw *hw, struct ieee80211_sta *sta, 3975 bool set); 3976 int (*set_key)(struct ieee80211_hw *hw, enum set_key_cmd cmd, 3977 struct ieee80211_vif *vif, struct ieee80211_sta *sta, 3978 struct ieee80211_key_conf *key); 3979 void (*update_tkip_key)(struct ieee80211_hw *hw, 3980 struct ieee80211_vif *vif, 3981 struct ieee80211_key_conf *conf, 3982 struct ieee80211_sta *sta, 3983 u32 iv32, u16 *phase1key); 3984 void (*set_rekey_data)(struct ieee80211_hw *hw, 3985 struct ieee80211_vif *vif, 3986 struct cfg80211_gtk_rekey_data *data); 3987 void (*set_default_unicast_key)(struct ieee80211_hw *hw, 3988 struct ieee80211_vif *vif, int idx); 3989 int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 3990 struct ieee80211_scan_request *req); 3991 void (*cancel_hw_scan)(struct ieee80211_hw *hw, 3992 struct ieee80211_vif *vif); 3993 int (*sched_scan_start)(struct ieee80211_hw *hw, 3994 struct ieee80211_vif *vif, 3995 struct cfg80211_sched_scan_request *req, 3996 struct ieee80211_scan_ies *ies); 3997 int (*sched_scan_stop)(struct ieee80211_hw *hw, 3998 struct ieee80211_vif *vif); 3999 void (*sw_scan_start)(struct ieee80211_hw *hw, 4000 struct ieee80211_vif *vif, 4001 const u8 *mac_addr); 4002 void (*sw_scan_complete)(struct ieee80211_hw *hw, 4003 struct ieee80211_vif *vif); 4004 int (*get_stats)(struct ieee80211_hw *hw, 4005 struct ieee80211_low_level_stats *stats); 4006 void (*get_key_seq)(struct ieee80211_hw *hw, 4007 struct ieee80211_key_conf *key, 4008 struct ieee80211_key_seq *seq); 4009 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value); 4010 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value); 4011 int (*sta_add)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4012 struct ieee80211_sta *sta); 4013 int (*sta_remove)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4014 struct ieee80211_sta *sta); 4015 #ifdef CONFIG_MAC80211_DEBUGFS 4016 void (*sta_add_debugfs)(struct ieee80211_hw *hw, 4017 struct ieee80211_vif *vif, 4018 struct ieee80211_sta *sta, 4019 struct dentry *dir); 4020 #endif 4021 void (*sta_notify)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4022 enum sta_notify_cmd, struct ieee80211_sta *sta); 4023 int (*sta_set_txpwr)(struct ieee80211_hw *hw, 4024 struct ieee80211_vif *vif, 4025 struct ieee80211_sta *sta); 4026 int (*sta_state)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4027 struct ieee80211_sta *sta, 4028 enum ieee80211_sta_state old_state, 4029 enum ieee80211_sta_state new_state); 4030 void (*sta_pre_rcu_remove)(struct ieee80211_hw *hw, 4031 struct ieee80211_vif *vif, 4032 struct ieee80211_sta *sta); 4033 void (*sta_rc_update)(struct ieee80211_hw *hw, 4034 struct ieee80211_vif *vif, 4035 struct ieee80211_sta *sta, 4036 u32 changed); 4037 void (*sta_rate_tbl_update)(struct ieee80211_hw *hw, 4038 struct ieee80211_vif *vif, 4039 struct ieee80211_sta *sta); 4040 void (*sta_statistics)(struct ieee80211_hw *hw, 4041 struct ieee80211_vif *vif, 4042 struct ieee80211_sta *sta, 4043 struct station_info *sinfo); 4044 int (*conf_tx)(struct ieee80211_hw *hw, 4045 struct ieee80211_vif *vif, u16 ac, 4046 const struct ieee80211_tx_queue_params *params); 4047 u64 (*get_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 4048 void (*set_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4049 u64 tsf); 4050 void (*offset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4051 s64 offset); 4052 void (*reset_tsf)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 4053 int (*tx_last_beacon)(struct ieee80211_hw *hw); 4054 4055 /** 4056 * @ampdu_action: 4057 * Perform a certain A-MPDU action. 4058 * The RA/TID combination determines the destination and TID we want 4059 * the ampdu action to be performed for. The action is defined through 4060 * ieee80211_ampdu_mlme_action. 4061 * When the action is set to %IEEE80211_AMPDU_TX_OPERATIONAL the driver 4062 * may neither send aggregates containing more subframes than @buf_size 4063 * nor send aggregates in a way that lost frames would exceed the 4064 * buffer size. If just limiting the aggregate size, this would be 4065 * possible with a buf_size of 8: 4066 * 4067 * - ``TX: 1.....7`` 4068 * - ``RX: 2....7`` (lost frame #1) 4069 * - ``TX: 8..1...`` 4070 * 4071 * which is invalid since #1 was now re-transmitted well past the 4072 * buffer size of 8. Correct ways to retransmit #1 would be: 4073 * 4074 * - ``TX: 1 or`` 4075 * - ``TX: 18 or`` 4076 * - ``TX: 81`` 4077 * 4078 * Even ``189`` would be wrong since 1 could be lost again. 4079 * 4080 * Returns a negative error code on failure. The driver may return 4081 * %IEEE80211_AMPDU_TX_START_IMMEDIATE for %IEEE80211_AMPDU_TX_START 4082 * if the session can start immediately. 4083 * 4084 * The callback can sleep. 4085 */ 4086 int (*ampdu_action)(struct ieee80211_hw *hw, 4087 struct ieee80211_vif *vif, 4088 struct ieee80211_ampdu_params *params); 4089 int (*get_survey)(struct ieee80211_hw *hw, int idx, 4090 struct survey_info *survey); 4091 void (*rfkill_poll)(struct ieee80211_hw *hw); 4092 void (*set_coverage_class)(struct ieee80211_hw *hw, s16 coverage_class); 4093 #ifdef CONFIG_NL80211_TESTMODE 4094 int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4095 void *data, int len); 4096 int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb, 4097 struct netlink_callback *cb, 4098 void *data, int len); 4099 #endif 4100 void (*flush)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4101 u32 queues, bool drop); 4102 void (*channel_switch)(struct ieee80211_hw *hw, 4103 struct ieee80211_vif *vif, 4104 struct ieee80211_channel_switch *ch_switch); 4105 int (*set_antenna)(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant); 4106 int (*get_antenna)(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant); 4107 4108 int (*remain_on_channel)(struct ieee80211_hw *hw, 4109 struct ieee80211_vif *vif, 4110 struct ieee80211_channel *chan, 4111 int duration, 4112 enum ieee80211_roc_type type); 4113 int (*cancel_remain_on_channel)(struct ieee80211_hw *hw, 4114 struct ieee80211_vif *vif); 4115 int (*set_ringparam)(struct ieee80211_hw *hw, u32 tx, u32 rx); 4116 void (*get_ringparam)(struct ieee80211_hw *hw, 4117 u32 *tx, u32 *tx_max, u32 *rx, u32 *rx_max); 4118 bool (*tx_frames_pending)(struct ieee80211_hw *hw); 4119 int (*set_bitrate_mask)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4120 const struct cfg80211_bitrate_mask *mask); 4121 void (*event_callback)(struct ieee80211_hw *hw, 4122 struct ieee80211_vif *vif, 4123 const struct ieee80211_event *event); 4124 4125 void (*allow_buffered_frames)(struct ieee80211_hw *hw, 4126 struct ieee80211_sta *sta, 4127 u16 tids, int num_frames, 4128 enum ieee80211_frame_release_type reason, 4129 bool more_data); 4130 void (*release_buffered_frames)(struct ieee80211_hw *hw, 4131 struct ieee80211_sta *sta, 4132 u16 tids, int num_frames, 4133 enum ieee80211_frame_release_type reason, 4134 bool more_data); 4135 4136 int (*get_et_sset_count)(struct ieee80211_hw *hw, 4137 struct ieee80211_vif *vif, int sset); 4138 void (*get_et_stats)(struct ieee80211_hw *hw, 4139 struct ieee80211_vif *vif, 4140 struct ethtool_stats *stats, u64 *data); 4141 void (*get_et_strings)(struct ieee80211_hw *hw, 4142 struct ieee80211_vif *vif, 4143 u32 sset, u8 *data); 4144 4145 void (*mgd_prepare_tx)(struct ieee80211_hw *hw, 4146 struct ieee80211_vif *vif, 4147 struct ieee80211_prep_tx_info *info); 4148 void (*mgd_complete_tx)(struct ieee80211_hw *hw, 4149 struct ieee80211_vif *vif, 4150 struct ieee80211_prep_tx_info *info); 4151 4152 void (*mgd_protect_tdls_discover)(struct ieee80211_hw *hw, 4153 struct ieee80211_vif *vif); 4154 4155 int (*add_chanctx)(struct ieee80211_hw *hw, 4156 struct ieee80211_chanctx_conf *ctx); 4157 void (*remove_chanctx)(struct ieee80211_hw *hw, 4158 struct ieee80211_chanctx_conf *ctx); 4159 void (*change_chanctx)(struct ieee80211_hw *hw, 4160 struct ieee80211_chanctx_conf *ctx, 4161 u32 changed); 4162 int (*assign_vif_chanctx)(struct ieee80211_hw *hw, 4163 struct ieee80211_vif *vif, 4164 struct ieee80211_chanctx_conf *ctx); 4165 void (*unassign_vif_chanctx)(struct ieee80211_hw *hw, 4166 struct ieee80211_vif *vif, 4167 struct ieee80211_chanctx_conf *ctx); 4168 int (*switch_vif_chanctx)(struct ieee80211_hw *hw, 4169 struct ieee80211_vif_chanctx_switch *vifs, 4170 int n_vifs, 4171 enum ieee80211_chanctx_switch_mode mode); 4172 4173 void (*reconfig_complete)(struct ieee80211_hw *hw, 4174 enum ieee80211_reconfig_type reconfig_type); 4175 4176 #if IS_ENABLED(CONFIG_IPV6) 4177 void (*ipv6_addr_change)(struct ieee80211_hw *hw, 4178 struct ieee80211_vif *vif, 4179 struct inet6_dev *idev); 4180 #endif 4181 void (*channel_switch_beacon)(struct ieee80211_hw *hw, 4182 struct ieee80211_vif *vif, 4183 struct cfg80211_chan_def *chandef); 4184 int (*pre_channel_switch)(struct ieee80211_hw *hw, 4185 struct ieee80211_vif *vif, 4186 struct ieee80211_channel_switch *ch_switch); 4187 4188 int (*post_channel_switch)(struct ieee80211_hw *hw, 4189 struct ieee80211_vif *vif); 4190 void (*abort_channel_switch)(struct ieee80211_hw *hw, 4191 struct ieee80211_vif *vif); 4192 void (*channel_switch_rx_beacon)(struct ieee80211_hw *hw, 4193 struct ieee80211_vif *vif, 4194 struct ieee80211_channel_switch *ch_switch); 4195 4196 int (*join_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 4197 void (*leave_ibss)(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 4198 u32 (*get_expected_throughput)(struct ieee80211_hw *hw, 4199 struct ieee80211_sta *sta); 4200 int (*get_txpower)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4201 int *dbm); 4202 4203 int (*tdls_channel_switch)(struct ieee80211_hw *hw, 4204 struct ieee80211_vif *vif, 4205 struct ieee80211_sta *sta, u8 oper_class, 4206 struct cfg80211_chan_def *chandef, 4207 struct sk_buff *tmpl_skb, u32 ch_sw_tm_ie); 4208 void (*tdls_cancel_channel_switch)(struct ieee80211_hw *hw, 4209 struct ieee80211_vif *vif, 4210 struct ieee80211_sta *sta); 4211 void (*tdls_recv_channel_switch)(struct ieee80211_hw *hw, 4212 struct ieee80211_vif *vif, 4213 struct ieee80211_tdls_ch_sw_params *params); 4214 4215 void (*wake_tx_queue)(struct ieee80211_hw *hw, 4216 struct ieee80211_txq *txq); 4217 void (*sync_rx_queues)(struct ieee80211_hw *hw); 4218 4219 int (*start_nan)(struct ieee80211_hw *hw, 4220 struct ieee80211_vif *vif, 4221 struct cfg80211_nan_conf *conf); 4222 int (*stop_nan)(struct ieee80211_hw *hw, 4223 struct ieee80211_vif *vif); 4224 int (*nan_change_conf)(struct ieee80211_hw *hw, 4225 struct ieee80211_vif *vif, 4226 struct cfg80211_nan_conf *conf, u32 changes); 4227 int (*add_nan_func)(struct ieee80211_hw *hw, 4228 struct ieee80211_vif *vif, 4229 const struct cfg80211_nan_func *nan_func); 4230 void (*del_nan_func)(struct ieee80211_hw *hw, 4231 struct ieee80211_vif *vif, 4232 u8 instance_id); 4233 bool (*can_aggregate_in_amsdu)(struct ieee80211_hw *hw, 4234 struct sk_buff *head, 4235 struct sk_buff *skb); 4236 int (*get_ftm_responder_stats)(struct ieee80211_hw *hw, 4237 struct ieee80211_vif *vif, 4238 struct cfg80211_ftm_responder_stats *ftm_stats); 4239 int (*start_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4240 struct cfg80211_pmsr_request *request); 4241 void (*abort_pmsr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4242 struct cfg80211_pmsr_request *request); 4243 int (*set_tid_config)(struct ieee80211_hw *hw, 4244 struct ieee80211_vif *vif, 4245 struct ieee80211_sta *sta, 4246 struct cfg80211_tid_config *tid_conf); 4247 int (*reset_tid_config)(struct ieee80211_hw *hw, 4248 struct ieee80211_vif *vif, 4249 struct ieee80211_sta *sta, u8 tids); 4250 void (*update_vif_offload)(struct ieee80211_hw *hw, 4251 struct ieee80211_vif *vif); 4252 void (*sta_set_4addr)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 4253 struct ieee80211_sta *sta, bool enabled); 4254 int (*set_sar_specs)(struct ieee80211_hw *hw, 4255 const struct cfg80211_sar_specs *sar); 4256 void (*sta_set_decap_offload)(struct ieee80211_hw *hw, 4257 struct ieee80211_vif *vif, 4258 struct ieee80211_sta *sta, bool enabled); 4259 void (*add_twt_setup)(struct ieee80211_hw *hw, 4260 struct ieee80211_sta *sta, 4261 struct ieee80211_twt_setup *twt); 4262 void (*twt_teardown_request)(struct ieee80211_hw *hw, 4263 struct ieee80211_sta *sta, u8 flowid); 4264 }; 4265 4266 /** 4267 * ieee80211_alloc_hw_nm - Allocate a new hardware device 4268 * 4269 * This must be called once for each hardware device. The returned pointer 4270 * must be used to refer to this device when calling other functions. 4271 * mac80211 allocates a private data area for the driver pointed to by 4272 * @priv in &struct ieee80211_hw, the size of this area is given as 4273 * @priv_data_len. 4274 * 4275 * @priv_data_len: length of private data 4276 * @ops: callbacks for this device 4277 * @requested_name: Requested name for this device. 4278 * NULL is valid value, and means use the default naming (phy%d) 4279 * 4280 * Return: A pointer to the new hardware device, or %NULL on error. 4281 */ 4282 struct ieee80211_hw *ieee80211_alloc_hw_nm(size_t priv_data_len, 4283 const struct ieee80211_ops *ops, 4284 const char *requested_name); 4285 4286 /** 4287 * ieee80211_alloc_hw - Allocate a new hardware device 4288 * 4289 * This must be called once for each hardware device. The returned pointer 4290 * must be used to refer to this device when calling other functions. 4291 * mac80211 allocates a private data area for the driver pointed to by 4292 * @priv in &struct ieee80211_hw, the size of this area is given as 4293 * @priv_data_len. 4294 * 4295 * @priv_data_len: length of private data 4296 * @ops: callbacks for this device 4297 * 4298 * Return: A pointer to the new hardware device, or %NULL on error. 4299 */ 4300 static inline 4301 struct ieee80211_hw *ieee80211_alloc_hw(size_t priv_data_len, 4302 const struct ieee80211_ops *ops) 4303 { 4304 return ieee80211_alloc_hw_nm(priv_data_len, ops, NULL); 4305 } 4306 4307 /** 4308 * ieee80211_register_hw - Register hardware device 4309 * 4310 * You must call this function before any other functions in 4311 * mac80211. Note that before a hardware can be registered, you 4312 * need to fill the contained wiphy's information. 4313 * 4314 * @hw: the device to register as returned by ieee80211_alloc_hw() 4315 * 4316 * Return: 0 on success. An error code otherwise. 4317 */ 4318 int ieee80211_register_hw(struct ieee80211_hw *hw); 4319 4320 /** 4321 * struct ieee80211_tpt_blink - throughput blink description 4322 * @throughput: throughput in Kbit/sec 4323 * @blink_time: blink time in milliseconds 4324 * (full cycle, ie. one off + one on period) 4325 */ 4326 struct ieee80211_tpt_blink { 4327 int throughput; 4328 int blink_time; 4329 }; 4330 4331 /** 4332 * enum ieee80211_tpt_led_trigger_flags - throughput trigger flags 4333 * @IEEE80211_TPT_LEDTRIG_FL_RADIO: enable blinking with radio 4334 * @IEEE80211_TPT_LEDTRIG_FL_WORK: enable blinking when working 4335 * @IEEE80211_TPT_LEDTRIG_FL_CONNECTED: enable blinking when at least one 4336 * interface is connected in some way, including being an AP 4337 */ 4338 enum ieee80211_tpt_led_trigger_flags { 4339 IEEE80211_TPT_LEDTRIG_FL_RADIO = BIT(0), 4340 IEEE80211_TPT_LEDTRIG_FL_WORK = BIT(1), 4341 IEEE80211_TPT_LEDTRIG_FL_CONNECTED = BIT(2), 4342 }; 4343 4344 #ifdef CONFIG_MAC80211_LEDS 4345 const char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw); 4346 const char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw); 4347 const char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw); 4348 const char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw); 4349 const char * 4350 __ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, 4351 unsigned int flags, 4352 const struct ieee80211_tpt_blink *blink_table, 4353 unsigned int blink_table_len); 4354 #endif 4355 /** 4356 * ieee80211_get_tx_led_name - get name of TX LED 4357 * 4358 * mac80211 creates a transmit LED trigger for each wireless hardware 4359 * that can be used to drive LEDs if your driver registers a LED device. 4360 * This function returns the name (or %NULL if not configured for LEDs) 4361 * of the trigger so you can automatically link the LED device. 4362 * 4363 * @hw: the hardware to get the LED trigger name for 4364 * 4365 * Return: The name of the LED trigger. %NULL if not configured for LEDs. 4366 */ 4367 static inline const char *ieee80211_get_tx_led_name(struct ieee80211_hw *hw) 4368 { 4369 #ifdef CONFIG_MAC80211_LEDS 4370 return __ieee80211_get_tx_led_name(hw); 4371 #else 4372 return NULL; 4373 #endif 4374 } 4375 4376 /** 4377 * ieee80211_get_rx_led_name - get name of RX LED 4378 * 4379 * mac80211 creates a receive LED trigger for each wireless hardware 4380 * that can be used to drive LEDs if your driver registers a LED device. 4381 * This function returns the name (or %NULL if not configured for LEDs) 4382 * of the trigger so you can automatically link the LED device. 4383 * 4384 * @hw: the hardware to get the LED trigger name for 4385 * 4386 * Return: The name of the LED trigger. %NULL if not configured for LEDs. 4387 */ 4388 static inline const char *ieee80211_get_rx_led_name(struct ieee80211_hw *hw) 4389 { 4390 #ifdef CONFIG_MAC80211_LEDS 4391 return __ieee80211_get_rx_led_name(hw); 4392 #else 4393 return NULL; 4394 #endif 4395 } 4396 4397 /** 4398 * ieee80211_get_assoc_led_name - get name of association LED 4399 * 4400 * mac80211 creates a association LED trigger for each wireless hardware 4401 * that can be used to drive LEDs if your driver registers a LED device. 4402 * This function returns the name (or %NULL if not configured for LEDs) 4403 * of the trigger so you can automatically link the LED device. 4404 * 4405 * @hw: the hardware to get the LED trigger name for 4406 * 4407 * Return: The name of the LED trigger. %NULL if not configured for LEDs. 4408 */ 4409 static inline const char *ieee80211_get_assoc_led_name(struct ieee80211_hw *hw) 4410 { 4411 #ifdef CONFIG_MAC80211_LEDS 4412 return __ieee80211_get_assoc_led_name(hw); 4413 #else 4414 return NULL; 4415 #endif 4416 } 4417 4418 /** 4419 * ieee80211_get_radio_led_name - get name of radio LED 4420 * 4421 * mac80211 creates a radio change LED trigger for each wireless hardware 4422 * that can be used to drive LEDs if your driver registers a LED device. 4423 * This function returns the name (or %NULL if not configured for LEDs) 4424 * of the trigger so you can automatically link the LED device. 4425 * 4426 * @hw: the hardware to get the LED trigger name for 4427 * 4428 * Return: The name of the LED trigger. %NULL if not configured for LEDs. 4429 */ 4430 static inline const char *ieee80211_get_radio_led_name(struct ieee80211_hw *hw) 4431 { 4432 #ifdef CONFIG_MAC80211_LEDS 4433 return __ieee80211_get_radio_led_name(hw); 4434 #else 4435 return NULL; 4436 #endif 4437 } 4438 4439 /** 4440 * ieee80211_create_tpt_led_trigger - create throughput LED trigger 4441 * @hw: the hardware to create the trigger for 4442 * @flags: trigger flags, see &enum ieee80211_tpt_led_trigger_flags 4443 * @blink_table: the blink table -- needs to be ordered by throughput 4444 * @blink_table_len: size of the blink table 4445 * 4446 * Return: %NULL (in case of error, or if no LED triggers are 4447 * configured) or the name of the new trigger. 4448 * 4449 * Note: This function must be called before ieee80211_register_hw(). 4450 */ 4451 static inline const char * 4452 ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw, unsigned int flags, 4453 const struct ieee80211_tpt_blink *blink_table, 4454 unsigned int blink_table_len) 4455 { 4456 #ifdef CONFIG_MAC80211_LEDS 4457 return __ieee80211_create_tpt_led_trigger(hw, flags, blink_table, 4458 blink_table_len); 4459 #else 4460 return NULL; 4461 #endif 4462 } 4463 4464 /** 4465 * ieee80211_unregister_hw - Unregister a hardware device 4466 * 4467 * This function instructs mac80211 to free allocated resources 4468 * and unregister netdevices from the networking subsystem. 4469 * 4470 * @hw: the hardware to unregister 4471 */ 4472 void ieee80211_unregister_hw(struct ieee80211_hw *hw); 4473 4474 /** 4475 * ieee80211_free_hw - free hardware descriptor 4476 * 4477 * This function frees everything that was allocated, including the 4478 * private data for the driver. You must call ieee80211_unregister_hw() 4479 * before calling this function. 4480 * 4481 * @hw: the hardware to free 4482 */ 4483 void ieee80211_free_hw(struct ieee80211_hw *hw); 4484 4485 /** 4486 * ieee80211_restart_hw - restart hardware completely 4487 * 4488 * Call this function when the hardware was restarted for some reason 4489 * (hardware error, ...) and the driver is unable to restore its state 4490 * by itself. mac80211 assumes that at this point the driver/hardware 4491 * is completely uninitialised and stopped, it starts the process by 4492 * calling the ->start() operation. The driver will need to reset all 4493 * internal state that it has prior to calling this function. 4494 * 4495 * @hw: the hardware to restart 4496 */ 4497 void ieee80211_restart_hw(struct ieee80211_hw *hw); 4498 4499 /** 4500 * ieee80211_rx_list - receive frame and store processed skbs in a list 4501 * 4502 * Use this function to hand received frames to mac80211. The receive 4503 * buffer in @skb must start with an IEEE 802.11 header. In case of a 4504 * paged @skb is used, the driver is recommended to put the ieee80211 4505 * header of the frame on the linear part of the @skb to avoid memory 4506 * allocation and/or memcpy by the stack. 4507 * 4508 * This function may not be called in IRQ context. Calls to this function 4509 * for a single hardware must be synchronized against each other. Calls to 4510 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be 4511 * mixed for a single hardware. Must not run concurrently with 4512 * ieee80211_tx_status() or ieee80211_tx_status_ni(). 4513 * 4514 * This function must be called with BHs disabled and RCU read lock 4515 * 4516 * @hw: the hardware this frame came in on 4517 * @sta: the station the frame was received from, or %NULL 4518 * @skb: the buffer to receive, owned by mac80211 after this call 4519 * @list: the destination list 4520 */ 4521 void ieee80211_rx_list(struct ieee80211_hw *hw, struct ieee80211_sta *sta, 4522 struct sk_buff *skb, struct list_head *list); 4523 4524 /** 4525 * ieee80211_rx_napi - receive frame from NAPI context 4526 * 4527 * Use this function to hand received frames to mac80211. The receive 4528 * buffer in @skb must start with an IEEE 802.11 header. In case of a 4529 * paged @skb is used, the driver is recommended to put the ieee80211 4530 * header of the frame on the linear part of the @skb to avoid memory 4531 * allocation and/or memcpy by the stack. 4532 * 4533 * This function may not be called in IRQ context. Calls to this function 4534 * for a single hardware must be synchronized against each other. Calls to 4535 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be 4536 * mixed for a single hardware. Must not run concurrently with 4537 * ieee80211_tx_status() or ieee80211_tx_status_ni(). 4538 * 4539 * This function must be called with BHs disabled. 4540 * 4541 * @hw: the hardware this frame came in on 4542 * @sta: the station the frame was received from, or %NULL 4543 * @skb: the buffer to receive, owned by mac80211 after this call 4544 * @napi: the NAPI context 4545 */ 4546 void ieee80211_rx_napi(struct ieee80211_hw *hw, struct ieee80211_sta *sta, 4547 struct sk_buff *skb, struct napi_struct *napi); 4548 4549 /** 4550 * ieee80211_rx - receive frame 4551 * 4552 * Use this function to hand received frames to mac80211. The receive 4553 * buffer in @skb must start with an IEEE 802.11 header. In case of a 4554 * paged @skb is used, the driver is recommended to put the ieee80211 4555 * header of the frame on the linear part of the @skb to avoid memory 4556 * allocation and/or memcpy by the stack. 4557 * 4558 * This function may not be called in IRQ context. Calls to this function 4559 * for a single hardware must be synchronized against each other. Calls to 4560 * this function, ieee80211_rx_ni() and ieee80211_rx_irqsafe() may not be 4561 * mixed for a single hardware. Must not run concurrently with 4562 * ieee80211_tx_status() or ieee80211_tx_status_ni(). 4563 * 4564 * In process context use instead ieee80211_rx_ni(). 4565 * 4566 * @hw: the hardware this frame came in on 4567 * @skb: the buffer to receive, owned by mac80211 after this call 4568 */ 4569 static inline void ieee80211_rx(struct ieee80211_hw *hw, struct sk_buff *skb) 4570 { 4571 ieee80211_rx_napi(hw, NULL, skb, NULL); 4572 } 4573 4574 /** 4575 * ieee80211_rx_irqsafe - receive frame 4576 * 4577 * Like ieee80211_rx() but can be called in IRQ context 4578 * (internally defers to a tasklet.) 4579 * 4580 * Calls to this function, ieee80211_rx() or ieee80211_rx_ni() may not 4581 * be mixed for a single hardware.Must not run concurrently with 4582 * ieee80211_tx_status() or ieee80211_tx_status_ni(). 4583 * 4584 * @hw: the hardware this frame came in on 4585 * @skb: the buffer to receive, owned by mac80211 after this call 4586 */ 4587 void ieee80211_rx_irqsafe(struct ieee80211_hw *hw, struct sk_buff *skb); 4588 4589 /** 4590 * ieee80211_rx_ni - receive frame (in process context) 4591 * 4592 * Like ieee80211_rx() but can be called in process context 4593 * (internally disables bottom halves). 4594 * 4595 * Calls to this function, ieee80211_rx() and ieee80211_rx_irqsafe() may 4596 * not be mixed for a single hardware. Must not run concurrently with 4597 * ieee80211_tx_status() or ieee80211_tx_status_ni(). 4598 * 4599 * @hw: the hardware this frame came in on 4600 * @skb: the buffer to receive, owned by mac80211 after this call 4601 */ 4602 static inline void ieee80211_rx_ni(struct ieee80211_hw *hw, 4603 struct sk_buff *skb) 4604 { 4605 local_bh_disable(); 4606 ieee80211_rx(hw, skb); 4607 local_bh_enable(); 4608 } 4609 4610 /** 4611 * ieee80211_sta_ps_transition - PS transition for connected sta 4612 * 4613 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS 4614 * flag set, use this function to inform mac80211 about a connected station 4615 * entering/leaving PS mode. 4616 * 4617 * This function may not be called in IRQ context or with softirqs enabled. 4618 * 4619 * Calls to this function for a single hardware must be synchronized against 4620 * each other. 4621 * 4622 * @sta: currently connected sta 4623 * @start: start or stop PS 4624 * 4625 * Return: 0 on success. -EINVAL when the requested PS mode is already set. 4626 */ 4627 int ieee80211_sta_ps_transition(struct ieee80211_sta *sta, bool start); 4628 4629 /** 4630 * ieee80211_sta_ps_transition_ni - PS transition for connected sta 4631 * (in process context) 4632 * 4633 * Like ieee80211_sta_ps_transition() but can be called in process context 4634 * (internally disables bottom halves). Concurrent call restriction still 4635 * applies. 4636 * 4637 * @sta: currently connected sta 4638 * @start: start or stop PS 4639 * 4640 * Return: Like ieee80211_sta_ps_transition(). 4641 */ 4642 static inline int ieee80211_sta_ps_transition_ni(struct ieee80211_sta *sta, 4643 bool start) 4644 { 4645 int ret; 4646 4647 local_bh_disable(); 4648 ret = ieee80211_sta_ps_transition(sta, start); 4649 local_bh_enable(); 4650 4651 return ret; 4652 } 4653 4654 /** 4655 * ieee80211_sta_pspoll - PS-Poll frame received 4656 * @sta: currently connected station 4657 * 4658 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set, 4659 * use this function to inform mac80211 that a PS-Poll frame from a 4660 * connected station was received. 4661 * This must be used in conjunction with ieee80211_sta_ps_transition() 4662 * and possibly ieee80211_sta_uapsd_trigger(); calls to all three must 4663 * be serialized. 4664 */ 4665 void ieee80211_sta_pspoll(struct ieee80211_sta *sta); 4666 4667 /** 4668 * ieee80211_sta_uapsd_trigger - (potential) U-APSD trigger frame received 4669 * @sta: currently connected station 4670 * @tid: TID of the received (potential) trigger frame 4671 * 4672 * When operating in AP mode with the %IEEE80211_HW_AP_LINK_PS flag set, 4673 * use this function to inform mac80211 that a (potential) trigger frame 4674 * from a connected station was received. 4675 * This must be used in conjunction with ieee80211_sta_ps_transition() 4676 * and possibly ieee80211_sta_pspoll(); calls to all three must be 4677 * serialized. 4678 * %IEEE80211_NUM_TIDS can be passed as the tid if the tid is unknown. 4679 * In this case, mac80211 will not check that this tid maps to an AC 4680 * that is trigger enabled and assume that the caller did the proper 4681 * checks. 4682 */ 4683 void ieee80211_sta_uapsd_trigger(struct ieee80211_sta *sta, u8 tid); 4684 4685 /* 4686 * The TX headroom reserved by mac80211 for its own tx_status functions. 4687 * This is enough for the radiotap header. 4688 */ 4689 #define IEEE80211_TX_STATUS_HEADROOM ALIGN(14, 4) 4690 4691 /** 4692 * ieee80211_sta_set_buffered - inform mac80211 about driver-buffered frames 4693 * @sta: &struct ieee80211_sta pointer for the sleeping station 4694 * @tid: the TID that has buffered frames 4695 * @buffered: indicates whether or not frames are buffered for this TID 4696 * 4697 * If a driver buffers frames for a powersave station instead of passing 4698 * them back to mac80211 for retransmission, the station may still need 4699 * to be told that there are buffered frames via the TIM bit. 4700 * 4701 * This function informs mac80211 whether or not there are frames that are 4702 * buffered in the driver for a given TID; mac80211 can then use this data 4703 * to set the TIM bit (NOTE: This may call back into the driver's set_tim 4704 * call! Beware of the locking!) 4705 * 4706 * If all frames are released to the station (due to PS-poll or uAPSD) 4707 * then the driver needs to inform mac80211 that there no longer are 4708 * frames buffered. However, when the station wakes up mac80211 assumes 4709 * that all buffered frames will be transmitted and clears this data, 4710 * drivers need to make sure they inform mac80211 about all buffered 4711 * frames on the sleep transition (sta_notify() with %STA_NOTIFY_SLEEP). 4712 * 4713 * Note that technically mac80211 only needs to know this per AC, not per 4714 * TID, but since driver buffering will inevitably happen per TID (since 4715 * it is related to aggregation) it is easier to make mac80211 map the 4716 * TID to the AC as required instead of keeping track in all drivers that 4717 * use this API. 4718 */ 4719 void ieee80211_sta_set_buffered(struct ieee80211_sta *sta, 4720 u8 tid, bool buffered); 4721 4722 /** 4723 * ieee80211_get_tx_rates - get the selected transmit rates for a packet 4724 * 4725 * Call this function in a driver with per-packet rate selection support 4726 * to combine the rate info in the packet tx info with the most recent 4727 * rate selection table for the station entry. 4728 * 4729 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 4730 * @sta: the receiver station to which this packet is sent. 4731 * @skb: the frame to be transmitted. 4732 * @dest: buffer for extracted rate/retry information 4733 * @max_rates: maximum number of rates to fetch 4734 */ 4735 void ieee80211_get_tx_rates(struct ieee80211_vif *vif, 4736 struct ieee80211_sta *sta, 4737 struct sk_buff *skb, 4738 struct ieee80211_tx_rate *dest, 4739 int max_rates); 4740 4741 /** 4742 * ieee80211_sta_set_expected_throughput - set the expected tpt for a station 4743 * 4744 * Call this function to notify mac80211 about a change in expected throughput 4745 * to a station. A driver for a device that does rate control in firmware can 4746 * call this function when the expected throughput estimate towards a station 4747 * changes. The information is used to tune the CoDel AQM applied to traffic 4748 * going towards that station (which can otherwise be too aggressive and cause 4749 * slow stations to starve). 4750 * 4751 * @pubsta: the station to set throughput for. 4752 * @thr: the current expected throughput in kbps. 4753 */ 4754 void ieee80211_sta_set_expected_throughput(struct ieee80211_sta *pubsta, 4755 u32 thr); 4756 4757 /** 4758 * ieee80211_tx_rate_update - transmit rate update callback 4759 * 4760 * Drivers should call this functions with a non-NULL pub sta 4761 * This function can be used in drivers that does not have provision 4762 * in updating the tx rate in data path. 4763 * 4764 * @hw: the hardware the frame was transmitted by 4765 * @pubsta: the station to update the tx rate for. 4766 * @info: tx status information 4767 */ 4768 void ieee80211_tx_rate_update(struct ieee80211_hw *hw, 4769 struct ieee80211_sta *pubsta, 4770 struct ieee80211_tx_info *info); 4771 4772 /** 4773 * ieee80211_tx_status - transmit status callback 4774 * 4775 * Call this function for all transmitted frames after they have been 4776 * transmitted. It is permissible to not call this function for 4777 * multicast frames but this can affect statistics. 4778 * 4779 * This function may not be called in IRQ context. Calls to this function 4780 * for a single hardware must be synchronized against each other. Calls 4781 * to this function, ieee80211_tx_status_ni() and ieee80211_tx_status_irqsafe() 4782 * may not be mixed for a single hardware. Must not run concurrently with 4783 * ieee80211_rx() or ieee80211_rx_ni(). 4784 * 4785 * @hw: the hardware the frame was transmitted by 4786 * @skb: the frame that was transmitted, owned by mac80211 after this call 4787 */ 4788 void ieee80211_tx_status(struct ieee80211_hw *hw, 4789 struct sk_buff *skb); 4790 4791 /** 4792 * ieee80211_tx_status_ext - extended transmit status callback 4793 * 4794 * This function can be used as a replacement for ieee80211_tx_status 4795 * in drivers that may want to provide extra information that does not 4796 * fit into &struct ieee80211_tx_info. 4797 * 4798 * Calls to this function for a single hardware must be synchronized 4799 * against each other. Calls to this function, ieee80211_tx_status_ni() 4800 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware. 4801 * 4802 * @hw: the hardware the frame was transmitted by 4803 * @status: tx status information 4804 */ 4805 void ieee80211_tx_status_ext(struct ieee80211_hw *hw, 4806 struct ieee80211_tx_status *status); 4807 4808 /** 4809 * ieee80211_tx_status_noskb - transmit status callback without skb 4810 * 4811 * This function can be used as a replacement for ieee80211_tx_status 4812 * in drivers that cannot reliably map tx status information back to 4813 * specific skbs. 4814 * 4815 * Calls to this function for a single hardware must be synchronized 4816 * against each other. Calls to this function, ieee80211_tx_status_ni() 4817 * and ieee80211_tx_status_irqsafe() may not be mixed for a single hardware. 4818 * 4819 * @hw: the hardware the frame was transmitted by 4820 * @sta: the receiver station to which this packet is sent 4821 * (NULL for multicast packets) 4822 * @info: tx status information 4823 */ 4824 static inline void ieee80211_tx_status_noskb(struct ieee80211_hw *hw, 4825 struct ieee80211_sta *sta, 4826 struct ieee80211_tx_info *info) 4827 { 4828 struct ieee80211_tx_status status = { 4829 .sta = sta, 4830 .info = info, 4831 }; 4832 4833 ieee80211_tx_status_ext(hw, &status); 4834 } 4835 4836 /** 4837 * ieee80211_tx_status_ni - transmit status callback (in process context) 4838 * 4839 * Like ieee80211_tx_status() but can be called in process context. 4840 * 4841 * Calls to this function, ieee80211_tx_status() and 4842 * ieee80211_tx_status_irqsafe() may not be mixed 4843 * for a single hardware. 4844 * 4845 * @hw: the hardware the frame was transmitted by 4846 * @skb: the frame that was transmitted, owned by mac80211 after this call 4847 */ 4848 static inline void ieee80211_tx_status_ni(struct ieee80211_hw *hw, 4849 struct sk_buff *skb) 4850 { 4851 local_bh_disable(); 4852 ieee80211_tx_status(hw, skb); 4853 local_bh_enable(); 4854 } 4855 4856 /** 4857 * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback 4858 * 4859 * Like ieee80211_tx_status() but can be called in IRQ context 4860 * (internally defers to a tasklet.) 4861 * 4862 * Calls to this function, ieee80211_tx_status() and 4863 * ieee80211_tx_status_ni() may not be mixed for a single hardware. 4864 * 4865 * @hw: the hardware the frame was transmitted by 4866 * @skb: the frame that was transmitted, owned by mac80211 after this call 4867 */ 4868 void ieee80211_tx_status_irqsafe(struct ieee80211_hw *hw, 4869 struct sk_buff *skb); 4870 4871 /** 4872 * ieee80211_tx_status_8023 - transmit status callback for 802.3 frame format 4873 * 4874 * Call this function for all transmitted data frames after their transmit 4875 * completion. This callback should only be called for data frames which 4876 * are using driver's (or hardware's) offload capability of encap/decap 4877 * 802.11 frames. 4878 * 4879 * This function may not be called in IRQ context. Calls to this function 4880 * for a single hardware must be synchronized against each other and all 4881 * calls in the same tx status family. 4882 * 4883 * @hw: the hardware the frame was transmitted by 4884 * @vif: the interface for which the frame was transmitted 4885 * @skb: the frame that was transmitted, owned by mac80211 after this call 4886 */ 4887 void ieee80211_tx_status_8023(struct ieee80211_hw *hw, 4888 struct ieee80211_vif *vif, 4889 struct sk_buff *skb); 4890 4891 /** 4892 * ieee80211_report_low_ack - report non-responding station 4893 * 4894 * When operating in AP-mode, call this function to report a non-responding 4895 * connected STA. 4896 * 4897 * @sta: the non-responding connected sta 4898 * @num_packets: number of packets sent to @sta without a response 4899 */ 4900 void ieee80211_report_low_ack(struct ieee80211_sta *sta, u32 num_packets); 4901 4902 #define IEEE80211_MAX_CNTDWN_COUNTERS_NUM 2 4903 4904 /** 4905 * struct ieee80211_mutable_offsets - mutable beacon offsets 4906 * @tim_offset: position of TIM element 4907 * @tim_length: size of TIM element 4908 * @cntdwn_counter_offs: array of IEEE80211_MAX_CNTDWN_COUNTERS_NUM offsets 4909 * to countdown counters. This array can contain zero values which 4910 * should be ignored. 4911 */ 4912 struct ieee80211_mutable_offsets { 4913 u16 tim_offset; 4914 u16 tim_length; 4915 4916 u16 cntdwn_counter_offs[IEEE80211_MAX_CNTDWN_COUNTERS_NUM]; 4917 }; 4918 4919 /** 4920 * ieee80211_beacon_get_template - beacon template generation function 4921 * @hw: pointer obtained from ieee80211_alloc_hw(). 4922 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 4923 * @offs: &struct ieee80211_mutable_offsets pointer to struct that will 4924 * receive the offsets that may be updated by the driver. 4925 * 4926 * If the driver implements beaconing modes, it must use this function to 4927 * obtain the beacon template. 4928 * 4929 * This function should be used if the beacon frames are generated by the 4930 * device, and then the driver must use the returned beacon as the template 4931 * The driver or the device are responsible to update the DTIM and, when 4932 * applicable, the CSA count. 4933 * 4934 * The driver is responsible for freeing the returned skb. 4935 * 4936 * Return: The beacon template. %NULL on error. 4937 */ 4938 struct sk_buff * 4939 ieee80211_beacon_get_template(struct ieee80211_hw *hw, 4940 struct ieee80211_vif *vif, 4941 struct ieee80211_mutable_offsets *offs); 4942 4943 /** 4944 * ieee80211_beacon_get_tim - beacon generation function 4945 * @hw: pointer obtained from ieee80211_alloc_hw(). 4946 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 4947 * @tim_offset: pointer to variable that will receive the TIM IE offset. 4948 * Set to 0 if invalid (in non-AP modes). 4949 * @tim_length: pointer to variable that will receive the TIM IE length, 4950 * (including the ID and length bytes!). 4951 * Set to 0 if invalid (in non-AP modes). 4952 * 4953 * If the driver implements beaconing modes, it must use this function to 4954 * obtain the beacon frame. 4955 * 4956 * If the beacon frames are generated by the host system (i.e., not in 4957 * hardware/firmware), the driver uses this function to get each beacon 4958 * frame from mac80211 -- it is responsible for calling this function exactly 4959 * once before the beacon is needed (e.g. based on hardware interrupt). 4960 * 4961 * The driver is responsible for freeing the returned skb. 4962 * 4963 * Return: The beacon template. %NULL on error. 4964 */ 4965 struct sk_buff *ieee80211_beacon_get_tim(struct ieee80211_hw *hw, 4966 struct ieee80211_vif *vif, 4967 u16 *tim_offset, u16 *tim_length); 4968 4969 /** 4970 * ieee80211_beacon_get - beacon generation function 4971 * @hw: pointer obtained from ieee80211_alloc_hw(). 4972 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 4973 * 4974 * See ieee80211_beacon_get_tim(). 4975 * 4976 * Return: See ieee80211_beacon_get_tim(). 4977 */ 4978 static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw, 4979 struct ieee80211_vif *vif) 4980 { 4981 return ieee80211_beacon_get_tim(hw, vif, NULL, NULL); 4982 } 4983 4984 /** 4985 * ieee80211_beacon_update_cntdwn - request mac80211 to decrement the beacon countdown 4986 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 4987 * 4988 * The beacon counter should be updated after each beacon transmission. 4989 * This function is called implicitly when 4990 * ieee80211_beacon_get/ieee80211_beacon_get_tim are called, however if the 4991 * beacon frames are generated by the device, the driver should call this 4992 * function after each beacon transmission to sync mac80211's beacon countdown. 4993 * 4994 * Return: new countdown value 4995 */ 4996 u8 ieee80211_beacon_update_cntdwn(struct ieee80211_vif *vif); 4997 4998 /** 4999 * ieee80211_beacon_set_cntdwn - request mac80211 to set beacon countdown 5000 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5001 * @counter: the new value for the counter 5002 * 5003 * The beacon countdown can be changed by the device, this API should be 5004 * used by the device driver to update csa counter in mac80211. 5005 * 5006 * It should never be used together with ieee80211_beacon_update_cntdwn(), 5007 * as it will cause a race condition around the counter value. 5008 */ 5009 void ieee80211_beacon_set_cntdwn(struct ieee80211_vif *vif, u8 counter); 5010 5011 /** 5012 * ieee80211_csa_finish - notify mac80211 about channel switch 5013 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5014 * 5015 * After a channel switch announcement was scheduled and the counter in this 5016 * announcement hits 1, this function must be called by the driver to 5017 * notify mac80211 that the channel can be changed. 5018 */ 5019 void ieee80211_csa_finish(struct ieee80211_vif *vif); 5020 5021 /** 5022 * ieee80211_beacon_cntdwn_is_complete - find out if countdown reached 1 5023 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5024 * 5025 * This function returns whether the countdown reached zero. 5026 */ 5027 bool ieee80211_beacon_cntdwn_is_complete(struct ieee80211_vif *vif); 5028 5029 /** 5030 * ieee80211_color_change_finish - notify mac80211 about color change 5031 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5032 * 5033 * After a color change announcement was scheduled and the counter in this 5034 * announcement hits 1, this function must be called by the driver to 5035 * notify mac80211 that the color can be changed 5036 */ 5037 void ieee80211_color_change_finish(struct ieee80211_vif *vif); 5038 5039 /** 5040 * ieee80211_proberesp_get - retrieve a Probe Response template 5041 * @hw: pointer obtained from ieee80211_alloc_hw(). 5042 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5043 * 5044 * Creates a Probe Response template which can, for example, be uploaded to 5045 * hardware. The destination address should be set by the caller. 5046 * 5047 * Can only be called in AP mode. 5048 * 5049 * Return: The Probe Response template. %NULL on error. 5050 */ 5051 struct sk_buff *ieee80211_proberesp_get(struct ieee80211_hw *hw, 5052 struct ieee80211_vif *vif); 5053 5054 /** 5055 * ieee80211_pspoll_get - retrieve a PS Poll template 5056 * @hw: pointer obtained from ieee80211_alloc_hw(). 5057 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5058 * 5059 * Creates a PS Poll a template which can, for example, uploaded to 5060 * hardware. The template must be updated after association so that correct 5061 * AID, BSSID and MAC address is used. 5062 * 5063 * Note: Caller (or hardware) is responsible for setting the 5064 * &IEEE80211_FCTL_PM bit. 5065 * 5066 * Return: The PS Poll template. %NULL on error. 5067 */ 5068 struct sk_buff *ieee80211_pspoll_get(struct ieee80211_hw *hw, 5069 struct ieee80211_vif *vif); 5070 5071 /** 5072 * ieee80211_nullfunc_get - retrieve a nullfunc template 5073 * @hw: pointer obtained from ieee80211_alloc_hw(). 5074 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5075 * @qos_ok: QoS NDP is acceptable to the caller, this should be set 5076 * if at all possible 5077 * 5078 * Creates a Nullfunc template which can, for example, uploaded to 5079 * hardware. The template must be updated after association so that correct 5080 * BSSID and address is used. 5081 * 5082 * If @qos_ndp is set and the association is to an AP with QoS/WMM, the 5083 * returned packet will be QoS NDP. 5084 * 5085 * Note: Caller (or hardware) is responsible for setting the 5086 * &IEEE80211_FCTL_PM bit as well as Duration and Sequence Control fields. 5087 * 5088 * Return: The nullfunc template. %NULL on error. 5089 */ 5090 struct sk_buff *ieee80211_nullfunc_get(struct ieee80211_hw *hw, 5091 struct ieee80211_vif *vif, 5092 bool qos_ok); 5093 5094 /** 5095 * ieee80211_probereq_get - retrieve a Probe Request template 5096 * @hw: pointer obtained from ieee80211_alloc_hw(). 5097 * @src_addr: source MAC address 5098 * @ssid: SSID buffer 5099 * @ssid_len: length of SSID 5100 * @tailroom: tailroom to reserve at end of SKB for IEs 5101 * 5102 * Creates a Probe Request template which can, for example, be uploaded to 5103 * hardware. 5104 * 5105 * Return: The Probe Request template. %NULL on error. 5106 */ 5107 struct sk_buff *ieee80211_probereq_get(struct ieee80211_hw *hw, 5108 const u8 *src_addr, 5109 const u8 *ssid, size_t ssid_len, 5110 size_t tailroom); 5111 5112 /** 5113 * ieee80211_rts_get - RTS frame generation function 5114 * @hw: pointer obtained from ieee80211_alloc_hw(). 5115 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5116 * @frame: pointer to the frame that is going to be protected by the RTS. 5117 * @frame_len: the frame length (in octets). 5118 * @frame_txctl: &struct ieee80211_tx_info of the frame. 5119 * @rts: The buffer where to store the RTS frame. 5120 * 5121 * If the RTS frames are generated by the host system (i.e., not in 5122 * hardware/firmware), the low-level driver uses this function to receive 5123 * the next RTS frame from the 802.11 code. The low-level is responsible 5124 * for calling this function before and RTS frame is needed. 5125 */ 5126 void ieee80211_rts_get(struct ieee80211_hw *hw, struct ieee80211_vif *vif, 5127 const void *frame, size_t frame_len, 5128 const struct ieee80211_tx_info *frame_txctl, 5129 struct ieee80211_rts *rts); 5130 5131 /** 5132 * ieee80211_rts_duration - Get the duration field for an RTS frame 5133 * @hw: pointer obtained from ieee80211_alloc_hw(). 5134 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5135 * @frame_len: the length of the frame that is going to be protected by the RTS. 5136 * @frame_txctl: &struct ieee80211_tx_info of the frame. 5137 * 5138 * If the RTS is generated in firmware, but the host system must provide 5139 * the duration field, the low-level driver uses this function to receive 5140 * the duration field value in little-endian byteorder. 5141 * 5142 * Return: The duration. 5143 */ 5144 __le16 ieee80211_rts_duration(struct ieee80211_hw *hw, 5145 struct ieee80211_vif *vif, size_t frame_len, 5146 const struct ieee80211_tx_info *frame_txctl); 5147 5148 /** 5149 * ieee80211_ctstoself_get - CTS-to-self frame generation function 5150 * @hw: pointer obtained from ieee80211_alloc_hw(). 5151 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5152 * @frame: pointer to the frame that is going to be protected by the CTS-to-self. 5153 * @frame_len: the frame length (in octets). 5154 * @frame_txctl: &struct ieee80211_tx_info of the frame. 5155 * @cts: The buffer where to store the CTS-to-self frame. 5156 * 5157 * If the CTS-to-self frames are generated by the host system (i.e., not in 5158 * hardware/firmware), the low-level driver uses this function to receive 5159 * the next CTS-to-self frame from the 802.11 code. The low-level is responsible 5160 * for calling this function before and CTS-to-self frame is needed. 5161 */ 5162 void ieee80211_ctstoself_get(struct ieee80211_hw *hw, 5163 struct ieee80211_vif *vif, 5164 const void *frame, size_t frame_len, 5165 const struct ieee80211_tx_info *frame_txctl, 5166 struct ieee80211_cts *cts); 5167 5168 /** 5169 * ieee80211_ctstoself_duration - Get the duration field for a CTS-to-self frame 5170 * @hw: pointer obtained from ieee80211_alloc_hw(). 5171 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5172 * @frame_len: the length of the frame that is going to be protected by the CTS-to-self. 5173 * @frame_txctl: &struct ieee80211_tx_info of the frame. 5174 * 5175 * If the CTS-to-self is generated in firmware, but the host system must provide 5176 * the duration field, the low-level driver uses this function to receive 5177 * the duration field value in little-endian byteorder. 5178 * 5179 * Return: The duration. 5180 */ 5181 __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw, 5182 struct ieee80211_vif *vif, 5183 size_t frame_len, 5184 const struct ieee80211_tx_info *frame_txctl); 5185 5186 /** 5187 * ieee80211_generic_frame_duration - Calculate the duration field for a frame 5188 * @hw: pointer obtained from ieee80211_alloc_hw(). 5189 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5190 * @band: the band to calculate the frame duration on 5191 * @frame_len: the length of the frame. 5192 * @rate: the rate at which the frame is going to be transmitted. 5193 * 5194 * Calculate the duration field of some generic frame, given its 5195 * length and transmission rate (in 100kbps). 5196 * 5197 * Return: The duration. 5198 */ 5199 __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw, 5200 struct ieee80211_vif *vif, 5201 enum nl80211_band band, 5202 size_t frame_len, 5203 struct ieee80211_rate *rate); 5204 5205 /** 5206 * ieee80211_get_buffered_bc - accessing buffered broadcast and multicast frames 5207 * @hw: pointer as obtained from ieee80211_alloc_hw(). 5208 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5209 * 5210 * Function for accessing buffered broadcast and multicast frames. If 5211 * hardware/firmware does not implement buffering of broadcast/multicast 5212 * frames when power saving is used, 802.11 code buffers them in the host 5213 * memory. The low-level driver uses this function to fetch next buffered 5214 * frame. In most cases, this is used when generating beacon frame. 5215 * 5216 * Return: A pointer to the next buffered skb or NULL if no more buffered 5217 * frames are available. 5218 * 5219 * Note: buffered frames are returned only after DTIM beacon frame was 5220 * generated with ieee80211_beacon_get() and the low-level driver must thus 5221 * call ieee80211_beacon_get() first. ieee80211_get_buffered_bc() returns 5222 * NULL if the previous generated beacon was not DTIM, so the low-level driver 5223 * does not need to check for DTIM beacons separately and should be able to 5224 * use common code for all beacons. 5225 */ 5226 struct sk_buff * 5227 ieee80211_get_buffered_bc(struct ieee80211_hw *hw, struct ieee80211_vif *vif); 5228 5229 /** 5230 * ieee80211_get_tkip_p1k_iv - get a TKIP phase 1 key for IV32 5231 * 5232 * This function returns the TKIP phase 1 key for the given IV32. 5233 * 5234 * @keyconf: the parameter passed with the set key 5235 * @iv32: IV32 to get the P1K for 5236 * @p1k: a buffer to which the key will be written, as 5 u16 values 5237 */ 5238 void ieee80211_get_tkip_p1k_iv(struct ieee80211_key_conf *keyconf, 5239 u32 iv32, u16 *p1k); 5240 5241 /** 5242 * ieee80211_get_tkip_p1k - get a TKIP phase 1 key 5243 * 5244 * This function returns the TKIP phase 1 key for the IV32 taken 5245 * from the given packet. 5246 * 5247 * @keyconf: the parameter passed with the set key 5248 * @skb: the packet to take the IV32 value from that will be encrypted 5249 * with this P1K 5250 * @p1k: a buffer to which the key will be written, as 5 u16 values 5251 */ 5252 static inline void ieee80211_get_tkip_p1k(struct ieee80211_key_conf *keyconf, 5253 struct sk_buff *skb, u16 *p1k) 5254 { 5255 struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; 5256 const u8 *data = (u8 *)hdr + ieee80211_hdrlen(hdr->frame_control); 5257 u32 iv32 = get_unaligned_le32(&data[4]); 5258 5259 ieee80211_get_tkip_p1k_iv(keyconf, iv32, p1k); 5260 } 5261 5262 /** 5263 * ieee80211_get_tkip_rx_p1k - get a TKIP phase 1 key for RX 5264 * 5265 * This function returns the TKIP phase 1 key for the given IV32 5266 * and transmitter address. 5267 * 5268 * @keyconf: the parameter passed with the set key 5269 * @ta: TA that will be used with the key 5270 * @iv32: IV32 to get the P1K for 5271 * @p1k: a buffer to which the key will be written, as 5 u16 values 5272 */ 5273 void ieee80211_get_tkip_rx_p1k(struct ieee80211_key_conf *keyconf, 5274 const u8 *ta, u32 iv32, u16 *p1k); 5275 5276 /** 5277 * ieee80211_get_tkip_p2k - get a TKIP phase 2 key 5278 * 5279 * This function computes the TKIP RC4 key for the IV values 5280 * in the packet. 5281 * 5282 * @keyconf: the parameter passed with the set key 5283 * @skb: the packet to take the IV32/IV16 values from that will be 5284 * encrypted with this key 5285 * @p2k: a buffer to which the key will be written, 16 bytes 5286 */ 5287 void ieee80211_get_tkip_p2k(struct ieee80211_key_conf *keyconf, 5288 struct sk_buff *skb, u8 *p2k); 5289 5290 /** 5291 * ieee80211_tkip_add_iv - write TKIP IV and Ext. IV to pos 5292 * 5293 * @pos: start of crypto header 5294 * @keyconf: the parameter passed with the set key 5295 * @pn: PN to add 5296 * 5297 * Returns: pointer to the octet following IVs (i.e. beginning of 5298 * the packet payload) 5299 * 5300 * This function writes the tkip IV value to pos (which should 5301 * point to the crypto header) 5302 */ 5303 u8 *ieee80211_tkip_add_iv(u8 *pos, struct ieee80211_key_conf *keyconf, u64 pn); 5304 5305 /** 5306 * ieee80211_get_key_rx_seq - get key RX sequence counter 5307 * 5308 * @keyconf: the parameter passed with the set key 5309 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only); 5310 * the value on TID 0 is also used for non-QoS frames. For 5311 * CMAC, only TID 0 is valid. 5312 * @seq: buffer to receive the sequence data 5313 * 5314 * This function allows a driver to retrieve the current RX IV/PNs 5315 * for the given key. It must not be called if IV checking is done 5316 * by the device and not by mac80211. 5317 * 5318 * Note that this function may only be called when no RX processing 5319 * can be done concurrently. 5320 */ 5321 void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf, 5322 int tid, struct ieee80211_key_seq *seq); 5323 5324 /** 5325 * ieee80211_set_key_rx_seq - set key RX sequence counter 5326 * 5327 * @keyconf: the parameter passed with the set key 5328 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only); 5329 * the value on TID 0 is also used for non-QoS frames. For 5330 * CMAC, only TID 0 is valid. 5331 * @seq: new sequence data 5332 * 5333 * This function allows a driver to set the current RX IV/PNs for the 5334 * given key. This is useful when resuming from WoWLAN sleep and GTK 5335 * rekey may have been done while suspended. It should not be called 5336 * if IV checking is done by the device and not by mac80211. 5337 * 5338 * Note that this function may only be called when no RX processing 5339 * can be done concurrently. 5340 */ 5341 void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf, 5342 int tid, struct ieee80211_key_seq *seq); 5343 5344 /** 5345 * ieee80211_remove_key - remove the given key 5346 * @keyconf: the parameter passed with the set key 5347 * 5348 * Remove the given key. If the key was uploaded to the hardware at the 5349 * time this function is called, it is not deleted in the hardware but 5350 * instead assumed to have been removed already. 5351 * 5352 * Note that due to locking considerations this function can (currently) 5353 * only be called during key iteration (ieee80211_iter_keys().) 5354 */ 5355 void ieee80211_remove_key(struct ieee80211_key_conf *keyconf); 5356 5357 /** 5358 * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN 5359 * @vif: the virtual interface to add the key on 5360 * @keyconf: new key data 5361 * 5362 * When GTK rekeying was done while the system was suspended, (a) new 5363 * key(s) will be available. These will be needed by mac80211 for proper 5364 * RX processing, so this function allows setting them. 5365 * 5366 * The function returns the newly allocated key structure, which will 5367 * have similar contents to the passed key configuration but point to 5368 * mac80211-owned memory. In case of errors, the function returns an 5369 * ERR_PTR(), use IS_ERR() etc. 5370 * 5371 * Note that this function assumes the key isn't added to hardware 5372 * acceleration, so no TX will be done with the key. Since it's a GTK 5373 * on managed (station) networks, this is true anyway. If the driver 5374 * calls this function from the resume callback and subsequently uses 5375 * the return code 1 to reconfigure the device, this key will be part 5376 * of the reconfiguration. 5377 * 5378 * Note that the driver should also call ieee80211_set_key_rx_seq() 5379 * for the new key for each TID to set up sequence counters properly. 5380 * 5381 * IMPORTANT: If this replaces a key that is present in the hardware, 5382 * then it will attempt to remove it during this call. In many cases 5383 * this isn't what you want, so call ieee80211_remove_key() first for 5384 * the key that's being replaced. 5385 */ 5386 struct ieee80211_key_conf * 5387 ieee80211_gtk_rekey_add(struct ieee80211_vif *vif, 5388 struct ieee80211_key_conf *keyconf); 5389 5390 /** 5391 * ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying 5392 * @vif: virtual interface the rekeying was done on 5393 * @bssid: The BSSID of the AP, for checking association 5394 * @replay_ctr: the new replay counter after GTK rekeying 5395 * @gfp: allocation flags 5396 */ 5397 void ieee80211_gtk_rekey_notify(struct ieee80211_vif *vif, const u8 *bssid, 5398 const u8 *replay_ctr, gfp_t gfp); 5399 5400 /** 5401 * ieee80211_key_mic_failure - increment MIC failure counter for the key 5402 * 5403 * Note: this is really only safe if no other RX function is called 5404 * at the same time. 5405 * 5406 * @keyconf: the key in question 5407 */ 5408 void ieee80211_key_mic_failure(struct ieee80211_key_conf *keyconf); 5409 5410 /** 5411 * ieee80211_key_replay - increment replay counter for the key 5412 * 5413 * Note: this is really only safe if no other RX function is called 5414 * at the same time. 5415 * 5416 * @keyconf: the key in question 5417 */ 5418 void ieee80211_key_replay(struct ieee80211_key_conf *keyconf); 5419 5420 /** 5421 * ieee80211_wake_queue - wake specific queue 5422 * @hw: pointer as obtained from ieee80211_alloc_hw(). 5423 * @queue: queue number (counted from zero). 5424 * 5425 * Drivers should use this function instead of netif_wake_queue. 5426 */ 5427 void ieee80211_wake_queue(struct ieee80211_hw *hw, int queue); 5428 5429 /** 5430 * ieee80211_stop_queue - stop specific queue 5431 * @hw: pointer as obtained from ieee80211_alloc_hw(). 5432 * @queue: queue number (counted from zero). 5433 * 5434 * Drivers should use this function instead of netif_stop_queue. 5435 */ 5436 void ieee80211_stop_queue(struct ieee80211_hw *hw, int queue); 5437 5438 /** 5439 * ieee80211_queue_stopped - test status of the queue 5440 * @hw: pointer as obtained from ieee80211_alloc_hw(). 5441 * @queue: queue number (counted from zero). 5442 * 5443 * Drivers should use this function instead of netif_stop_queue. 5444 * 5445 * Return: %true if the queue is stopped. %false otherwise. 5446 */ 5447 5448 int ieee80211_queue_stopped(struct ieee80211_hw *hw, int queue); 5449 5450 /** 5451 * ieee80211_stop_queues - stop all queues 5452 * @hw: pointer as obtained from ieee80211_alloc_hw(). 5453 * 5454 * Drivers should use this function instead of netif_stop_queue. 5455 */ 5456 void ieee80211_stop_queues(struct ieee80211_hw *hw); 5457 5458 /** 5459 * ieee80211_wake_queues - wake all queues 5460 * @hw: pointer as obtained from ieee80211_alloc_hw(). 5461 * 5462 * Drivers should use this function instead of netif_wake_queue. 5463 */ 5464 void ieee80211_wake_queues(struct ieee80211_hw *hw); 5465 5466 /** 5467 * ieee80211_scan_completed - completed hardware scan 5468 * 5469 * When hardware scan offload is used (i.e. the hw_scan() callback is 5470 * assigned) this function needs to be called by the driver to notify 5471 * mac80211 that the scan finished. This function can be called from 5472 * any context, including hardirq context. 5473 * 5474 * @hw: the hardware that finished the scan 5475 * @info: information about the completed scan 5476 */ 5477 void ieee80211_scan_completed(struct ieee80211_hw *hw, 5478 struct cfg80211_scan_info *info); 5479 5480 /** 5481 * ieee80211_sched_scan_results - got results from scheduled scan 5482 * 5483 * When a scheduled scan is running, this function needs to be called by the 5484 * driver whenever there are new scan results available. 5485 * 5486 * @hw: the hardware that is performing scheduled scans 5487 */ 5488 void ieee80211_sched_scan_results(struct ieee80211_hw *hw); 5489 5490 /** 5491 * ieee80211_sched_scan_stopped - inform that the scheduled scan has stopped 5492 * 5493 * When a scheduled scan is running, this function can be called by 5494 * the driver if it needs to stop the scan to perform another task. 5495 * Usual scenarios are drivers that cannot continue the scheduled scan 5496 * while associating, for instance. 5497 * 5498 * @hw: the hardware that is performing scheduled scans 5499 */ 5500 void ieee80211_sched_scan_stopped(struct ieee80211_hw *hw); 5501 5502 /** 5503 * enum ieee80211_interface_iteration_flags - interface iteration flags 5504 * @IEEE80211_IFACE_ITER_NORMAL: Iterate over all interfaces that have 5505 * been added to the driver; However, note that during hardware 5506 * reconfiguration (after restart_hw) it will iterate over a new 5507 * interface and over all the existing interfaces even if they 5508 * haven't been re-added to the driver yet. 5509 * @IEEE80211_IFACE_ITER_RESUME_ALL: During resume, iterate over all 5510 * interfaces, even if they haven't been re-added to the driver yet. 5511 * @IEEE80211_IFACE_ITER_ACTIVE: Iterate only active interfaces (netdev is up). 5512 * @IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER: Skip any interfaces where SDATA 5513 * is not in the driver. This may fix crashes during firmware recovery 5514 * for instance. 5515 */ 5516 enum ieee80211_interface_iteration_flags { 5517 IEEE80211_IFACE_ITER_NORMAL = 0, 5518 IEEE80211_IFACE_ITER_RESUME_ALL = BIT(0), 5519 IEEE80211_IFACE_ITER_ACTIVE = BIT(1), 5520 IEEE80211_IFACE_SKIP_SDATA_NOT_IN_DRIVER = BIT(2), 5521 }; 5522 5523 /** 5524 * ieee80211_iterate_interfaces - iterate interfaces 5525 * 5526 * This function iterates over the interfaces associated with a given 5527 * hardware and calls the callback for them. This includes active as well as 5528 * inactive interfaces. This function allows the iterator function to sleep. 5529 * Will iterate over a new interface during add_interface(). 5530 * 5531 * @hw: the hardware struct of which the interfaces should be iterated over 5532 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags 5533 * @iterator: the iterator function to call 5534 * @data: first argument of the iterator function 5535 */ 5536 void ieee80211_iterate_interfaces(struct ieee80211_hw *hw, u32 iter_flags, 5537 void (*iterator)(void *data, u8 *mac, 5538 struct ieee80211_vif *vif), 5539 void *data); 5540 5541 /** 5542 * ieee80211_iterate_active_interfaces - iterate active interfaces 5543 * 5544 * This function iterates over the interfaces associated with a given 5545 * hardware that are currently active and calls the callback for them. 5546 * This function allows the iterator function to sleep, when the iterator 5547 * function is atomic @ieee80211_iterate_active_interfaces_atomic can 5548 * be used. 5549 * Does not iterate over a new interface during add_interface(). 5550 * 5551 * @hw: the hardware struct of which the interfaces should be iterated over 5552 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags 5553 * @iterator: the iterator function to call 5554 * @data: first argument of the iterator function 5555 */ 5556 static inline void 5557 ieee80211_iterate_active_interfaces(struct ieee80211_hw *hw, u32 iter_flags, 5558 void (*iterator)(void *data, u8 *mac, 5559 struct ieee80211_vif *vif), 5560 void *data) 5561 { 5562 ieee80211_iterate_interfaces(hw, 5563 iter_flags | IEEE80211_IFACE_ITER_ACTIVE, 5564 iterator, data); 5565 } 5566 5567 /** 5568 * ieee80211_iterate_active_interfaces_atomic - iterate active interfaces 5569 * 5570 * This function iterates over the interfaces associated with a given 5571 * hardware that are currently active and calls the callback for them. 5572 * This function requires the iterator callback function to be atomic, 5573 * if that is not desired, use @ieee80211_iterate_active_interfaces instead. 5574 * Does not iterate over a new interface during add_interface(). 5575 * 5576 * @hw: the hardware struct of which the interfaces should be iterated over 5577 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags 5578 * @iterator: the iterator function to call, cannot sleep 5579 * @data: first argument of the iterator function 5580 */ 5581 void ieee80211_iterate_active_interfaces_atomic(struct ieee80211_hw *hw, 5582 u32 iter_flags, 5583 void (*iterator)(void *data, 5584 u8 *mac, 5585 struct ieee80211_vif *vif), 5586 void *data); 5587 5588 /** 5589 * ieee80211_iterate_active_interfaces_mtx - iterate active interfaces 5590 * 5591 * This function iterates over the interfaces associated with a given 5592 * hardware that are currently active and calls the callback for them. 5593 * This version can only be used while holding the wiphy mutex. 5594 * 5595 * @hw: the hardware struct of which the interfaces should be iterated over 5596 * @iter_flags: iteration flags, see &enum ieee80211_interface_iteration_flags 5597 * @iterator: the iterator function to call, cannot sleep 5598 * @data: first argument of the iterator function 5599 */ 5600 void ieee80211_iterate_active_interfaces_mtx(struct ieee80211_hw *hw, 5601 u32 iter_flags, 5602 void (*iterator)(void *data, 5603 u8 *mac, 5604 struct ieee80211_vif *vif), 5605 void *data); 5606 5607 /** 5608 * ieee80211_iterate_stations_atomic - iterate stations 5609 * 5610 * This function iterates over all stations associated with a given 5611 * hardware that are currently uploaded to the driver and calls the callback 5612 * function for them. 5613 * This function requires the iterator callback function to be atomic, 5614 * 5615 * @hw: the hardware struct of which the interfaces should be iterated over 5616 * @iterator: the iterator function to call, cannot sleep 5617 * @data: first argument of the iterator function 5618 */ 5619 void ieee80211_iterate_stations_atomic(struct ieee80211_hw *hw, 5620 void (*iterator)(void *data, 5621 struct ieee80211_sta *sta), 5622 void *data); 5623 /** 5624 * ieee80211_queue_work - add work onto the mac80211 workqueue 5625 * 5626 * Drivers and mac80211 use this to add work onto the mac80211 workqueue. 5627 * This helper ensures drivers are not queueing work when they should not be. 5628 * 5629 * @hw: the hardware struct for the interface we are adding work for 5630 * @work: the work we want to add onto the mac80211 workqueue 5631 */ 5632 void ieee80211_queue_work(struct ieee80211_hw *hw, struct work_struct *work); 5633 5634 /** 5635 * ieee80211_queue_delayed_work - add work onto the mac80211 workqueue 5636 * 5637 * Drivers and mac80211 use this to queue delayed work onto the mac80211 5638 * workqueue. 5639 * 5640 * @hw: the hardware struct for the interface we are adding work for 5641 * @dwork: delayable work to queue onto the mac80211 workqueue 5642 * @delay: number of jiffies to wait before queueing 5643 */ 5644 void ieee80211_queue_delayed_work(struct ieee80211_hw *hw, 5645 struct delayed_work *dwork, 5646 unsigned long delay); 5647 5648 /** 5649 * ieee80211_start_tx_ba_session - Start a tx Block Ack session. 5650 * @sta: the station for which to start a BA session 5651 * @tid: the TID to BA on. 5652 * @timeout: session timeout value (in TUs) 5653 * 5654 * Return: success if addBA request was sent, failure otherwise 5655 * 5656 * Although mac80211/low level driver/user space application can estimate 5657 * the need to start aggregation on a certain RA/TID, the session level 5658 * will be managed by the mac80211. 5659 */ 5660 int ieee80211_start_tx_ba_session(struct ieee80211_sta *sta, u16 tid, 5661 u16 timeout); 5662 5663 /** 5664 * ieee80211_start_tx_ba_cb_irqsafe - low level driver ready to aggregate. 5665 * @vif: &struct ieee80211_vif pointer from the add_interface callback 5666 * @ra: receiver address of the BA session recipient. 5667 * @tid: the TID to BA on. 5668 * 5669 * This function must be called by low level driver once it has 5670 * finished with preparations for the BA session. It can be called 5671 * from any context. 5672 */ 5673 void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, 5674 u16 tid); 5675 5676 /** 5677 * ieee80211_stop_tx_ba_session - Stop a Block Ack session. 5678 * @sta: the station whose BA session to stop 5679 * @tid: the TID to stop BA. 5680 * 5681 * Return: negative error if the TID is invalid, or no aggregation active 5682 * 5683 * Although mac80211/low level driver/user space application can estimate 5684 * the need to stop aggregation on a certain RA/TID, the session level 5685 * will be managed by the mac80211. 5686 */ 5687 int ieee80211_stop_tx_ba_session(struct ieee80211_sta *sta, u16 tid); 5688 5689 /** 5690 * ieee80211_stop_tx_ba_cb_irqsafe - low level driver ready to stop aggregate. 5691 * @vif: &struct ieee80211_vif pointer from the add_interface callback 5692 * @ra: receiver address of the BA session recipient. 5693 * @tid: the desired TID to BA on. 5694 * 5695 * This function must be called by low level driver once it has 5696 * finished with preparations for the BA session tear down. It 5697 * can be called from any context. 5698 */ 5699 void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_vif *vif, const u8 *ra, 5700 u16 tid); 5701 5702 /** 5703 * ieee80211_find_sta - find a station 5704 * 5705 * @vif: virtual interface to look for station on 5706 * @addr: station's address 5707 * 5708 * Return: The station, if found. %NULL otherwise. 5709 * 5710 * Note: This function must be called under RCU lock and the 5711 * resulting pointer is only valid under RCU lock as well. 5712 */ 5713 struct ieee80211_sta *ieee80211_find_sta(struct ieee80211_vif *vif, 5714 const u8 *addr); 5715 5716 /** 5717 * ieee80211_find_sta_by_ifaddr - find a station on hardware 5718 * 5719 * @hw: pointer as obtained from ieee80211_alloc_hw() 5720 * @addr: remote station's address 5721 * @localaddr: local address (vif->sdata->vif.addr). Use NULL for 'any'. 5722 * 5723 * Return: The station, if found. %NULL otherwise. 5724 * 5725 * Note: This function must be called under RCU lock and the 5726 * resulting pointer is only valid under RCU lock as well. 5727 * 5728 * NOTE: You may pass NULL for localaddr, but then you will just get 5729 * the first STA that matches the remote address 'addr'. 5730 * We can have multiple STA associated with multiple 5731 * logical stations (e.g. consider a station connecting to another 5732 * BSSID on the same AP hardware without disconnecting first). 5733 * In this case, the result of this method with localaddr NULL 5734 * is not reliable. 5735 * 5736 * DO NOT USE THIS FUNCTION with localaddr NULL if at all possible. 5737 */ 5738 struct ieee80211_sta *ieee80211_find_sta_by_ifaddr(struct ieee80211_hw *hw, 5739 const u8 *addr, 5740 const u8 *localaddr); 5741 5742 /** 5743 * ieee80211_sta_block_awake - block station from waking up 5744 * @hw: the hardware 5745 * @pubsta: the station 5746 * @block: whether to block or unblock 5747 * 5748 * Some devices require that all frames that are on the queues 5749 * for a specific station that went to sleep are flushed before 5750 * a poll response or frames after the station woke up can be 5751 * delivered to that it. Note that such frames must be rejected 5752 * by the driver as filtered, with the appropriate status flag. 5753 * 5754 * This function allows implementing this mode in a race-free 5755 * manner. 5756 * 5757 * To do this, a driver must keep track of the number of frames 5758 * still enqueued for a specific station. If this number is not 5759 * zero when the station goes to sleep, the driver must call 5760 * this function to force mac80211 to consider the station to 5761 * be asleep regardless of the station's actual state. Once the 5762 * number of outstanding frames reaches zero, the driver must 5763 * call this function again to unblock the station. That will 5764 * cause mac80211 to be able to send ps-poll responses, and if 5765 * the station queried in the meantime then frames will also 5766 * be sent out as a result of this. Additionally, the driver 5767 * will be notified that the station woke up some time after 5768 * it is unblocked, regardless of whether the station actually 5769 * woke up while blocked or not. 5770 */ 5771 void ieee80211_sta_block_awake(struct ieee80211_hw *hw, 5772 struct ieee80211_sta *pubsta, bool block); 5773 5774 /** 5775 * ieee80211_sta_eosp - notify mac80211 about end of SP 5776 * @pubsta: the station 5777 * 5778 * When a device transmits frames in a way that it can't tell 5779 * mac80211 in the TX status about the EOSP, it must clear the 5780 * %IEEE80211_TX_STATUS_EOSP bit and call this function instead. 5781 * This applies for PS-Poll as well as uAPSD. 5782 * 5783 * Note that just like with _tx_status() and _rx() drivers must 5784 * not mix calls to irqsafe/non-irqsafe versions, this function 5785 * must not be mixed with those either. Use the all irqsafe, or 5786 * all non-irqsafe, don't mix! 5787 * 5788 * NB: the _irqsafe version of this function doesn't exist, no 5789 * driver needs it right now. Don't call this function if 5790 * you'd need the _irqsafe version, look at the git history 5791 * and restore the _irqsafe version! 5792 */ 5793 void ieee80211_sta_eosp(struct ieee80211_sta *pubsta); 5794 5795 /** 5796 * ieee80211_send_eosp_nullfunc - ask mac80211 to send NDP with EOSP 5797 * @pubsta: the station 5798 * @tid: the tid of the NDP 5799 * 5800 * Sometimes the device understands that it needs to close 5801 * the Service Period unexpectedly. This can happen when 5802 * sending frames that are filling holes in the BA window. 5803 * In this case, the device can ask mac80211 to send a 5804 * Nullfunc frame with EOSP set. When that happens, the 5805 * driver must have called ieee80211_sta_set_buffered() to 5806 * let mac80211 know that there are no buffered frames any 5807 * more, otherwise mac80211 will get the more_data bit wrong. 5808 * The low level driver must have made sure that the frame 5809 * will be sent despite the station being in power-save. 5810 * Mac80211 won't call allow_buffered_frames(). 5811 * Note that calling this function, doesn't exempt the driver 5812 * from closing the EOSP properly, it will still have to call 5813 * ieee80211_sta_eosp when the NDP is sent. 5814 */ 5815 void ieee80211_send_eosp_nullfunc(struct ieee80211_sta *pubsta, int tid); 5816 5817 /** 5818 * ieee80211_sta_register_airtime - register airtime usage for a sta/tid 5819 * 5820 * Register airtime usage for a given sta on a given tid. The driver must call 5821 * this function to notify mac80211 that a station used a certain amount of 5822 * airtime. This information will be used by the TXQ scheduler to schedule 5823 * stations in a way that ensures airtime fairness. 5824 * 5825 * The reported airtime should as a minimum include all time that is spent 5826 * transmitting to the remote station, including overhead and padding, but not 5827 * including time spent waiting for a TXOP. If the time is not reported by the 5828 * hardware it can in some cases be calculated from the rate and known frame 5829 * composition. When possible, the time should include any failed transmission 5830 * attempts. 5831 * 5832 * The driver can either call this function synchronously for every packet or 5833 * aggregate, or asynchronously as airtime usage information becomes available. 5834 * TX and RX airtime can be reported together, or separately by setting one of 5835 * them to 0. 5836 * 5837 * @pubsta: the station 5838 * @tid: the TID to register airtime for 5839 * @tx_airtime: airtime used during TX (in usec) 5840 * @rx_airtime: airtime used during RX (in usec) 5841 */ 5842 void ieee80211_sta_register_airtime(struct ieee80211_sta *pubsta, u8 tid, 5843 u32 tx_airtime, u32 rx_airtime); 5844 5845 /** 5846 * ieee80211_txq_airtime_check - check if a txq can send frame to device 5847 * 5848 * @hw: pointer obtained from ieee80211_alloc_hw() 5849 * @txq: pointer obtained from station or virtual interface 5850 * 5851 * Return true if the AQL's airtime limit has not been reached and the txq can 5852 * continue to send more packets to the device. Otherwise return false. 5853 */ 5854 bool 5855 ieee80211_txq_airtime_check(struct ieee80211_hw *hw, struct ieee80211_txq *txq); 5856 5857 /** 5858 * ieee80211_iter_keys - iterate keys programmed into the device 5859 * @hw: pointer obtained from ieee80211_alloc_hw() 5860 * @vif: virtual interface to iterate, may be %NULL for all 5861 * @iter: iterator function that will be called for each key 5862 * @iter_data: custom data to pass to the iterator function 5863 * 5864 * This function can be used to iterate all the keys known to 5865 * mac80211, even those that weren't previously programmed into 5866 * the device. This is intended for use in WoWLAN if the device 5867 * needs reprogramming of the keys during suspend. Note that due 5868 * to locking reasons, it is also only safe to call this at few 5869 * spots since it must hold the RTNL and be able to sleep. 5870 * 5871 * The order in which the keys are iterated matches the order 5872 * in which they were originally installed and handed to the 5873 * set_key callback. 5874 */ 5875 void ieee80211_iter_keys(struct ieee80211_hw *hw, 5876 struct ieee80211_vif *vif, 5877 void (*iter)(struct ieee80211_hw *hw, 5878 struct ieee80211_vif *vif, 5879 struct ieee80211_sta *sta, 5880 struct ieee80211_key_conf *key, 5881 void *data), 5882 void *iter_data); 5883 5884 /** 5885 * ieee80211_iter_keys_rcu - iterate keys programmed into the device 5886 * @hw: pointer obtained from ieee80211_alloc_hw() 5887 * @vif: virtual interface to iterate, may be %NULL for all 5888 * @iter: iterator function that will be called for each key 5889 * @iter_data: custom data to pass to the iterator function 5890 * 5891 * This function can be used to iterate all the keys known to 5892 * mac80211, even those that weren't previously programmed into 5893 * the device. Note that due to locking reasons, keys of station 5894 * in removal process will be skipped. 5895 * 5896 * This function requires being called in an RCU critical section, 5897 * and thus iter must be atomic. 5898 */ 5899 void ieee80211_iter_keys_rcu(struct ieee80211_hw *hw, 5900 struct ieee80211_vif *vif, 5901 void (*iter)(struct ieee80211_hw *hw, 5902 struct ieee80211_vif *vif, 5903 struct ieee80211_sta *sta, 5904 struct ieee80211_key_conf *key, 5905 void *data), 5906 void *iter_data); 5907 5908 /** 5909 * ieee80211_iter_chan_contexts_atomic - iterate channel contexts 5910 * @hw: pointer obtained from ieee80211_alloc_hw(). 5911 * @iter: iterator function 5912 * @iter_data: data passed to iterator function 5913 * 5914 * Iterate all active channel contexts. This function is atomic and 5915 * doesn't acquire any locks internally that might be held in other 5916 * places while calling into the driver. 5917 * 5918 * The iterator will not find a context that's being added (during 5919 * the driver callback to add it) but will find it while it's being 5920 * removed. 5921 * 5922 * Note that during hardware restart, all contexts that existed 5923 * before the restart are considered already present so will be 5924 * found while iterating, whether they've been re-added already 5925 * or not. 5926 */ 5927 void ieee80211_iter_chan_contexts_atomic( 5928 struct ieee80211_hw *hw, 5929 void (*iter)(struct ieee80211_hw *hw, 5930 struct ieee80211_chanctx_conf *chanctx_conf, 5931 void *data), 5932 void *iter_data); 5933 5934 /** 5935 * ieee80211_ap_probereq_get - retrieve a Probe Request template 5936 * @hw: pointer obtained from ieee80211_alloc_hw(). 5937 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5938 * 5939 * Creates a Probe Request template which can, for example, be uploaded to 5940 * hardware. The template is filled with bssid, ssid and supported rate 5941 * information. This function must only be called from within the 5942 * .bss_info_changed callback function and only in managed mode. The function 5943 * is only useful when the interface is associated, otherwise it will return 5944 * %NULL. 5945 * 5946 * Return: The Probe Request template. %NULL on error. 5947 */ 5948 struct sk_buff *ieee80211_ap_probereq_get(struct ieee80211_hw *hw, 5949 struct ieee80211_vif *vif); 5950 5951 /** 5952 * ieee80211_beacon_loss - inform hardware does not receive beacons 5953 * 5954 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5955 * 5956 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER and 5957 * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the 5958 * hardware is not receiving beacons with this function. 5959 */ 5960 void ieee80211_beacon_loss(struct ieee80211_vif *vif); 5961 5962 /** 5963 * ieee80211_connection_loss - inform hardware has lost connection to the AP 5964 * 5965 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5966 * 5967 * When beacon filtering is enabled with %IEEE80211_VIF_BEACON_FILTER, and 5968 * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver 5969 * needs to inform if the connection to the AP has been lost. 5970 * The function may also be called if the connection needs to be terminated 5971 * for some other reason, even if %IEEE80211_HW_CONNECTION_MONITOR isn't set. 5972 * 5973 * This function will cause immediate change to disassociated state, 5974 * without connection recovery attempts. 5975 */ 5976 void ieee80211_connection_loss(struct ieee80211_vif *vif); 5977 5978 /** 5979 * ieee80211_disconnect - request disconnection 5980 * 5981 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5982 * @reconnect: immediate reconnect is desired 5983 * 5984 * Request disconnection from the current network and, if enabled, send a 5985 * hint to the higher layers that immediate reconnect is desired. 5986 */ 5987 void ieee80211_disconnect(struct ieee80211_vif *vif, bool reconnect); 5988 5989 /** 5990 * ieee80211_resume_disconnect - disconnect from AP after resume 5991 * 5992 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 5993 * 5994 * Instructs mac80211 to disconnect from the AP after resume. 5995 * Drivers can use this after WoWLAN if they know that the 5996 * connection cannot be kept up, for example because keys were 5997 * used while the device was asleep but the replay counters or 5998 * similar cannot be retrieved from the device during resume. 5999 * 6000 * Note that due to implementation issues, if the driver uses 6001 * the reconfiguration functionality during resume the interface 6002 * will still be added as associated first during resume and then 6003 * disconnect normally later. 6004 * 6005 * This function can only be called from the resume callback and 6006 * the driver must not be holding any of its own locks while it 6007 * calls this function, or at least not any locks it needs in the 6008 * key configuration paths (if it supports HW crypto). 6009 */ 6010 void ieee80211_resume_disconnect(struct ieee80211_vif *vif); 6011 6012 /** 6013 * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring 6014 * rssi threshold triggered 6015 * 6016 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6017 * @rssi_event: the RSSI trigger event type 6018 * @rssi_level: new RSSI level value or 0 if not available 6019 * @gfp: context flags 6020 * 6021 * When the %IEEE80211_VIF_SUPPORTS_CQM_RSSI is set, and a connection quality 6022 * monitoring is configured with an rssi threshold, the driver will inform 6023 * whenever the rssi level reaches the threshold. 6024 */ 6025 void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, 6026 enum nl80211_cqm_rssi_threshold_event rssi_event, 6027 s32 rssi_level, 6028 gfp_t gfp); 6029 6030 /** 6031 * ieee80211_cqm_beacon_loss_notify - inform CQM of beacon loss 6032 * 6033 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6034 * @gfp: context flags 6035 */ 6036 void ieee80211_cqm_beacon_loss_notify(struct ieee80211_vif *vif, gfp_t gfp); 6037 6038 /** 6039 * ieee80211_radar_detected - inform that a radar was detected 6040 * 6041 * @hw: pointer as obtained from ieee80211_alloc_hw() 6042 */ 6043 void ieee80211_radar_detected(struct ieee80211_hw *hw); 6044 6045 /** 6046 * ieee80211_chswitch_done - Complete channel switch process 6047 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6048 * @success: make the channel switch successful or not 6049 * 6050 * Complete the channel switch post-process: set the new operational channel 6051 * and wake up the suspended queues. 6052 */ 6053 void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success); 6054 6055 /** 6056 * ieee80211_request_smps - request SM PS transition 6057 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6058 * @smps_mode: new SM PS mode 6059 * 6060 * This allows the driver to request an SM PS transition in managed 6061 * mode. This is useful when the driver has more information than 6062 * the stack about possible interference, for example by bluetooth. 6063 */ 6064 void ieee80211_request_smps(struct ieee80211_vif *vif, 6065 enum ieee80211_smps_mode smps_mode); 6066 6067 /** 6068 * ieee80211_ready_on_channel - notification of remain-on-channel start 6069 * @hw: pointer as obtained from ieee80211_alloc_hw() 6070 */ 6071 void ieee80211_ready_on_channel(struct ieee80211_hw *hw); 6072 6073 /** 6074 * ieee80211_remain_on_channel_expired - remain_on_channel duration expired 6075 * @hw: pointer as obtained from ieee80211_alloc_hw() 6076 */ 6077 void ieee80211_remain_on_channel_expired(struct ieee80211_hw *hw); 6078 6079 /** 6080 * ieee80211_stop_rx_ba_session - callback to stop existing BA sessions 6081 * 6082 * in order not to harm the system performance and user experience, the device 6083 * may request not to allow any rx ba session and tear down existing rx ba 6084 * sessions based on system constraints such as periodic BT activity that needs 6085 * to limit wlan activity (eg.sco or a2dp)." 6086 * in such cases, the intention is to limit the duration of the rx ppdu and 6087 * therefore prevent the peer device to use a-mpdu aggregation. 6088 * 6089 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6090 * @ba_rx_bitmap: Bit map of open rx ba per tid 6091 * @addr: & to bssid mac address 6092 */ 6093 void ieee80211_stop_rx_ba_session(struct ieee80211_vif *vif, u16 ba_rx_bitmap, 6094 const u8 *addr); 6095 6096 /** 6097 * ieee80211_mark_rx_ba_filtered_frames - move RX BA window and mark filtered 6098 * @pubsta: station struct 6099 * @tid: the session's TID 6100 * @ssn: starting sequence number of the bitmap, all frames before this are 6101 * assumed to be out of the window after the call 6102 * @filtered: bitmap of filtered frames, BIT(0) is the @ssn entry etc. 6103 * @received_mpdus: number of received mpdus in firmware 6104 * 6105 * This function moves the BA window and releases all frames before @ssn, and 6106 * marks frames marked in the bitmap as having been filtered. Afterwards, it 6107 * checks if any frames in the window starting from @ssn can now be released 6108 * (in case they were only waiting for frames that were filtered.) 6109 */ 6110 void ieee80211_mark_rx_ba_filtered_frames(struct ieee80211_sta *pubsta, u8 tid, 6111 u16 ssn, u64 filtered, 6112 u16 received_mpdus); 6113 6114 /** 6115 * ieee80211_send_bar - send a BlockAckReq frame 6116 * 6117 * can be used to flush pending frames from the peer's aggregation reorder 6118 * buffer. 6119 * 6120 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6121 * @ra: the peer's destination address 6122 * @tid: the TID of the aggregation session 6123 * @ssn: the new starting sequence number for the receiver 6124 */ 6125 void ieee80211_send_bar(struct ieee80211_vif *vif, u8 *ra, u16 tid, u16 ssn); 6126 6127 /** 6128 * ieee80211_manage_rx_ba_offl - helper to queue an RX BA work 6129 * @vif: &struct ieee80211_vif pointer from the add_interface callback 6130 * @addr: station mac address 6131 * @tid: the rx tid 6132 */ 6133 void ieee80211_manage_rx_ba_offl(struct ieee80211_vif *vif, const u8 *addr, 6134 unsigned int tid); 6135 6136 /** 6137 * ieee80211_start_rx_ba_session_offl - start a Rx BA session 6138 * 6139 * Some device drivers may offload part of the Rx aggregation flow including 6140 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx 6141 * reordering. 6142 * 6143 * Create structures responsible for reordering so device drivers may call here 6144 * when they complete AddBa negotiation. 6145 * 6146 * @vif: &struct ieee80211_vif pointer from the add_interface callback 6147 * @addr: station mac address 6148 * @tid: the rx tid 6149 */ 6150 static inline void ieee80211_start_rx_ba_session_offl(struct ieee80211_vif *vif, 6151 const u8 *addr, u16 tid) 6152 { 6153 if (WARN_ON(tid >= IEEE80211_NUM_TIDS)) 6154 return; 6155 ieee80211_manage_rx_ba_offl(vif, addr, tid); 6156 } 6157 6158 /** 6159 * ieee80211_stop_rx_ba_session_offl - stop a Rx BA session 6160 * 6161 * Some device drivers may offload part of the Rx aggregation flow including 6162 * AddBa/DelBa negotiation but may otherwise be incapable of full Rx 6163 * reordering. 6164 * 6165 * Destroy structures responsible for reordering so device drivers may call here 6166 * when they complete DelBa negotiation. 6167 * 6168 * @vif: &struct ieee80211_vif pointer from the add_interface callback 6169 * @addr: station mac address 6170 * @tid: the rx tid 6171 */ 6172 static inline void ieee80211_stop_rx_ba_session_offl(struct ieee80211_vif *vif, 6173 const u8 *addr, u16 tid) 6174 { 6175 if (WARN_ON(tid >= IEEE80211_NUM_TIDS)) 6176 return; 6177 ieee80211_manage_rx_ba_offl(vif, addr, tid + IEEE80211_NUM_TIDS); 6178 } 6179 6180 /** 6181 * ieee80211_rx_ba_timer_expired - stop a Rx BA session due to timeout 6182 * 6183 * Some device drivers do not offload AddBa/DelBa negotiation, but handle rx 6184 * buffer reording internally, and therefore also handle the session timer. 6185 * 6186 * Trigger the timeout flow, which sends a DelBa. 6187 * 6188 * @vif: &struct ieee80211_vif pointer from the add_interface callback 6189 * @addr: station mac address 6190 * @tid: the rx tid 6191 */ 6192 void ieee80211_rx_ba_timer_expired(struct ieee80211_vif *vif, 6193 const u8 *addr, unsigned int tid); 6194 6195 /* Rate control API */ 6196 6197 /** 6198 * struct ieee80211_tx_rate_control - rate control information for/from RC algo 6199 * 6200 * @hw: The hardware the algorithm is invoked for. 6201 * @sband: The band this frame is being transmitted on. 6202 * @bss_conf: the current BSS configuration 6203 * @skb: the skb that will be transmitted, the control information in it needs 6204 * to be filled in 6205 * @reported_rate: The rate control algorithm can fill this in to indicate 6206 * which rate should be reported to userspace as the current rate and 6207 * used for rate calculations in the mesh network. 6208 * @rts: whether RTS will be used for this frame because it is longer than the 6209 * RTS threshold 6210 * @short_preamble: whether mac80211 will request short-preamble transmission 6211 * if the selected rate supports it 6212 * @rate_idx_mask: user-requested (legacy) rate mask 6213 * @rate_idx_mcs_mask: user-requested MCS rate mask (NULL if not in use) 6214 * @bss: whether this frame is sent out in AP or IBSS mode 6215 */ 6216 struct ieee80211_tx_rate_control { 6217 struct ieee80211_hw *hw; 6218 struct ieee80211_supported_band *sband; 6219 struct ieee80211_bss_conf *bss_conf; 6220 struct sk_buff *skb; 6221 struct ieee80211_tx_rate reported_rate; 6222 bool rts, short_preamble; 6223 u32 rate_idx_mask; 6224 u8 *rate_idx_mcs_mask; 6225 bool bss; 6226 }; 6227 6228 /** 6229 * enum rate_control_capabilities - rate control capabilities 6230 */ 6231 enum rate_control_capabilities { 6232 /** 6233 * @RATE_CTRL_CAPA_VHT_EXT_NSS_BW: 6234 * Support for extended NSS BW support (dot11VHTExtendedNSSCapable) 6235 * Note that this is only looked at if the minimum number of chains 6236 * that the AP uses is < the number of TX chains the hardware has, 6237 * otherwise the NSS difference doesn't bother us. 6238 */ 6239 RATE_CTRL_CAPA_VHT_EXT_NSS_BW = BIT(0), 6240 /** 6241 * @RATE_CTRL_CAPA_AMPDU_TRIGGER: 6242 * mac80211 should start A-MPDU sessions on tx 6243 */ 6244 RATE_CTRL_CAPA_AMPDU_TRIGGER = BIT(1), 6245 }; 6246 6247 struct rate_control_ops { 6248 unsigned long capa; 6249 const char *name; 6250 void *(*alloc)(struct ieee80211_hw *hw); 6251 void (*add_debugfs)(struct ieee80211_hw *hw, void *priv, 6252 struct dentry *debugfsdir); 6253 void (*free)(void *priv); 6254 6255 void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp); 6256 void (*rate_init)(void *priv, struct ieee80211_supported_band *sband, 6257 struct cfg80211_chan_def *chandef, 6258 struct ieee80211_sta *sta, void *priv_sta); 6259 void (*rate_update)(void *priv, struct ieee80211_supported_band *sband, 6260 struct cfg80211_chan_def *chandef, 6261 struct ieee80211_sta *sta, void *priv_sta, 6262 u32 changed); 6263 void (*free_sta)(void *priv, struct ieee80211_sta *sta, 6264 void *priv_sta); 6265 6266 void (*tx_status_ext)(void *priv, 6267 struct ieee80211_supported_band *sband, 6268 void *priv_sta, struct ieee80211_tx_status *st); 6269 void (*tx_status)(void *priv, struct ieee80211_supported_band *sband, 6270 struct ieee80211_sta *sta, void *priv_sta, 6271 struct sk_buff *skb); 6272 void (*get_rate)(void *priv, struct ieee80211_sta *sta, void *priv_sta, 6273 struct ieee80211_tx_rate_control *txrc); 6274 6275 void (*add_sta_debugfs)(void *priv, void *priv_sta, 6276 struct dentry *dir); 6277 6278 u32 (*get_expected_throughput)(void *priv_sta); 6279 }; 6280 6281 static inline int rate_supported(struct ieee80211_sta *sta, 6282 enum nl80211_band band, 6283 int index) 6284 { 6285 return (sta == NULL || sta->supp_rates[band] & BIT(index)); 6286 } 6287 6288 static inline s8 6289 rate_lowest_index(struct ieee80211_supported_band *sband, 6290 struct ieee80211_sta *sta) 6291 { 6292 int i; 6293 6294 for (i = 0; i < sband->n_bitrates; i++) 6295 if (rate_supported(sta, sband->band, i)) 6296 return i; 6297 6298 /* warn when we cannot find a rate. */ 6299 WARN_ON_ONCE(1); 6300 6301 /* and return 0 (the lowest index) */ 6302 return 0; 6303 } 6304 6305 static inline 6306 bool rate_usable_index_exists(struct ieee80211_supported_band *sband, 6307 struct ieee80211_sta *sta) 6308 { 6309 unsigned int i; 6310 6311 for (i = 0; i < sband->n_bitrates; i++) 6312 if (rate_supported(sta, sband->band, i)) 6313 return true; 6314 return false; 6315 } 6316 6317 /** 6318 * rate_control_set_rates - pass the sta rate selection to mac80211/driver 6319 * 6320 * When not doing a rate control probe to test rates, rate control should pass 6321 * its rate selection to mac80211. If the driver supports receiving a station 6322 * rate table, it will use it to ensure that frames are always sent based on 6323 * the most recent rate control module decision. 6324 * 6325 * @hw: pointer as obtained from ieee80211_alloc_hw() 6326 * @pubsta: &struct ieee80211_sta pointer to the target destination. 6327 * @rates: new tx rate set to be used for this station. 6328 */ 6329 int rate_control_set_rates(struct ieee80211_hw *hw, 6330 struct ieee80211_sta *pubsta, 6331 struct ieee80211_sta_rates *rates); 6332 6333 int ieee80211_rate_control_register(const struct rate_control_ops *ops); 6334 void ieee80211_rate_control_unregister(const struct rate_control_ops *ops); 6335 6336 static inline bool 6337 conf_is_ht20(struct ieee80211_conf *conf) 6338 { 6339 return conf->chandef.width == NL80211_CHAN_WIDTH_20; 6340 } 6341 6342 static inline bool 6343 conf_is_ht40_minus(struct ieee80211_conf *conf) 6344 { 6345 return conf->chandef.width == NL80211_CHAN_WIDTH_40 && 6346 conf->chandef.center_freq1 < conf->chandef.chan->center_freq; 6347 } 6348 6349 static inline bool 6350 conf_is_ht40_plus(struct ieee80211_conf *conf) 6351 { 6352 return conf->chandef.width == NL80211_CHAN_WIDTH_40 && 6353 conf->chandef.center_freq1 > conf->chandef.chan->center_freq; 6354 } 6355 6356 static inline bool 6357 conf_is_ht40(struct ieee80211_conf *conf) 6358 { 6359 return conf->chandef.width == NL80211_CHAN_WIDTH_40; 6360 } 6361 6362 static inline bool 6363 conf_is_ht(struct ieee80211_conf *conf) 6364 { 6365 return (conf->chandef.width != NL80211_CHAN_WIDTH_5) && 6366 (conf->chandef.width != NL80211_CHAN_WIDTH_10) && 6367 (conf->chandef.width != NL80211_CHAN_WIDTH_20_NOHT); 6368 } 6369 6370 static inline enum nl80211_iftype 6371 ieee80211_iftype_p2p(enum nl80211_iftype type, bool p2p) 6372 { 6373 if (p2p) { 6374 switch (type) { 6375 case NL80211_IFTYPE_STATION: 6376 return NL80211_IFTYPE_P2P_CLIENT; 6377 case NL80211_IFTYPE_AP: 6378 return NL80211_IFTYPE_P2P_GO; 6379 default: 6380 break; 6381 } 6382 } 6383 return type; 6384 } 6385 6386 static inline enum nl80211_iftype 6387 ieee80211_vif_type_p2p(struct ieee80211_vif *vif) 6388 { 6389 return ieee80211_iftype_p2p(vif->type, vif->p2p); 6390 } 6391 6392 /** 6393 * ieee80211_update_mu_groups - set the VHT MU-MIMO groud data 6394 * 6395 * @vif: the specified virtual interface 6396 * @membership: 64 bits array - a bit is set if station is member of the group 6397 * @position: 2 bits per group id indicating the position in the group 6398 * 6399 * Note: This function assumes that the given vif is valid and the position and 6400 * membership data is of the correct size and are in the same byte order as the 6401 * matching GroupId management frame. 6402 * Calls to this function need to be serialized with RX path. 6403 */ 6404 void ieee80211_update_mu_groups(struct ieee80211_vif *vif, 6405 const u8 *membership, const u8 *position); 6406 6407 void ieee80211_enable_rssi_reports(struct ieee80211_vif *vif, 6408 int rssi_min_thold, 6409 int rssi_max_thold); 6410 6411 void ieee80211_disable_rssi_reports(struct ieee80211_vif *vif); 6412 6413 /** 6414 * ieee80211_ave_rssi - report the average RSSI for the specified interface 6415 * 6416 * @vif: the specified virtual interface 6417 * 6418 * Note: This function assumes that the given vif is valid. 6419 * 6420 * Return: The average RSSI value for the requested interface, or 0 if not 6421 * applicable. 6422 */ 6423 int ieee80211_ave_rssi(struct ieee80211_vif *vif); 6424 6425 /** 6426 * ieee80211_report_wowlan_wakeup - report WoWLAN wakeup 6427 * @vif: virtual interface 6428 * @wakeup: wakeup reason(s) 6429 * @gfp: allocation flags 6430 * 6431 * See cfg80211_report_wowlan_wakeup(). 6432 */ 6433 void ieee80211_report_wowlan_wakeup(struct ieee80211_vif *vif, 6434 struct cfg80211_wowlan_wakeup *wakeup, 6435 gfp_t gfp); 6436 6437 /** 6438 * ieee80211_tx_prepare_skb - prepare an 802.11 skb for transmission 6439 * @hw: pointer as obtained from ieee80211_alloc_hw() 6440 * @vif: virtual interface 6441 * @skb: frame to be sent from within the driver 6442 * @band: the band to transmit on 6443 * @sta: optional pointer to get the station to send the frame to 6444 * 6445 * Note: must be called under RCU lock 6446 */ 6447 bool ieee80211_tx_prepare_skb(struct ieee80211_hw *hw, 6448 struct ieee80211_vif *vif, struct sk_buff *skb, 6449 int band, struct ieee80211_sta **sta); 6450 6451 /** 6452 * ieee80211_parse_tx_radiotap - Sanity-check and parse the radiotap header 6453 * of injected frames. 6454 * 6455 * To accurately parse and take into account rate and retransmission fields, 6456 * you must initialize the chandef field in the ieee80211_tx_info structure 6457 * of the skb before calling this function. 6458 * 6459 * @skb: packet injected by userspace 6460 * @dev: the &struct device of this 802.11 device 6461 */ 6462 bool ieee80211_parse_tx_radiotap(struct sk_buff *skb, 6463 struct net_device *dev); 6464 6465 /** 6466 * struct ieee80211_noa_data - holds temporary data for tracking P2P NoA state 6467 * 6468 * @next_tsf: TSF timestamp of the next absent state change 6469 * @has_next_tsf: next absent state change event pending 6470 * 6471 * @absent: descriptor bitmask, set if GO is currently absent 6472 * 6473 * private: 6474 * 6475 * @count: count fields from the NoA descriptors 6476 * @desc: adjusted data from the NoA 6477 */ 6478 struct ieee80211_noa_data { 6479 u32 next_tsf; 6480 bool has_next_tsf; 6481 6482 u8 absent; 6483 6484 u8 count[IEEE80211_P2P_NOA_DESC_MAX]; 6485 struct { 6486 u32 start; 6487 u32 duration; 6488 u32 interval; 6489 } desc[IEEE80211_P2P_NOA_DESC_MAX]; 6490 }; 6491 6492 /** 6493 * ieee80211_parse_p2p_noa - initialize NoA tracking data from P2P IE 6494 * 6495 * @attr: P2P NoA IE 6496 * @data: NoA tracking data 6497 * @tsf: current TSF timestamp 6498 * 6499 * Return: number of successfully parsed descriptors 6500 */ 6501 int ieee80211_parse_p2p_noa(const struct ieee80211_p2p_noa_attr *attr, 6502 struct ieee80211_noa_data *data, u32 tsf); 6503 6504 /** 6505 * ieee80211_update_p2p_noa - get next pending P2P GO absent state change 6506 * 6507 * @data: NoA tracking data 6508 * @tsf: current TSF timestamp 6509 */ 6510 void ieee80211_update_p2p_noa(struct ieee80211_noa_data *data, u32 tsf); 6511 6512 /** 6513 * ieee80211_tdls_oper_request - request userspace to perform a TDLS operation 6514 * @vif: virtual interface 6515 * @peer: the peer's destination address 6516 * @oper: the requested TDLS operation 6517 * @reason_code: reason code for the operation, valid for TDLS teardown 6518 * @gfp: allocation flags 6519 * 6520 * See cfg80211_tdls_oper_request(). 6521 */ 6522 void ieee80211_tdls_oper_request(struct ieee80211_vif *vif, const u8 *peer, 6523 enum nl80211_tdls_operation oper, 6524 u16 reason_code, gfp_t gfp); 6525 6526 /** 6527 * ieee80211_reserve_tid - request to reserve a specific TID 6528 * 6529 * There is sometimes a need (such as in TDLS) for blocking the driver from 6530 * using a specific TID so that the FW can use it for certain operations such 6531 * as sending PTI requests. To make sure that the driver doesn't use that TID, 6532 * this function must be called as it flushes out packets on this TID and marks 6533 * it as blocked, so that any transmit for the station on this TID will be 6534 * redirected to the alternative TID in the same AC. 6535 * 6536 * Note that this function blocks and may call back into the driver, so it 6537 * should be called without driver locks held. Also note this function should 6538 * only be called from the driver's @sta_state callback. 6539 * 6540 * @sta: the station to reserve the TID for 6541 * @tid: the TID to reserve 6542 * 6543 * Returns: 0 on success, else on failure 6544 */ 6545 int ieee80211_reserve_tid(struct ieee80211_sta *sta, u8 tid); 6546 6547 /** 6548 * ieee80211_unreserve_tid - request to unreserve a specific TID 6549 * 6550 * Once there is no longer any need for reserving a certain TID, this function 6551 * should be called, and no longer will packets have their TID modified for 6552 * preventing use of this TID in the driver. 6553 * 6554 * Note that this function blocks and acquires a lock, so it should be called 6555 * without driver locks held. Also note this function should only be called 6556 * from the driver's @sta_state callback. 6557 * 6558 * @sta: the station 6559 * @tid: the TID to unreserve 6560 */ 6561 void ieee80211_unreserve_tid(struct ieee80211_sta *sta, u8 tid); 6562 6563 /** 6564 * ieee80211_tx_dequeue - dequeue a packet from a software tx queue 6565 * 6566 * @hw: pointer as obtained from ieee80211_alloc_hw() 6567 * @txq: pointer obtained from station or virtual interface, or from 6568 * ieee80211_next_txq() 6569 * 6570 * Returns the skb if successful, %NULL if no frame was available. 6571 * 6572 * Note that this must be called in an rcu_read_lock() critical section, 6573 * which can only be released after the SKB was handled. Some pointers in 6574 * skb->cb, e.g. the key pointer, are protected by RCU and thus the 6575 * critical section must persist not just for the duration of this call 6576 * but for the duration of the frame handling. 6577 * However, also note that while in the wake_tx_queue() method, 6578 * rcu_read_lock() is already held. 6579 * 6580 * softirqs must also be disabled when this function is called. 6581 * In process context, use ieee80211_tx_dequeue_ni() instead. 6582 */ 6583 struct sk_buff *ieee80211_tx_dequeue(struct ieee80211_hw *hw, 6584 struct ieee80211_txq *txq); 6585 6586 /** 6587 * ieee80211_tx_dequeue_ni - dequeue a packet from a software tx queue 6588 * (in process context) 6589 * 6590 * Like ieee80211_tx_dequeue() but can be called in process context 6591 * (internally disables bottom halves). 6592 * 6593 * @hw: pointer as obtained from ieee80211_alloc_hw() 6594 * @txq: pointer obtained from station or virtual interface, or from 6595 * ieee80211_next_txq() 6596 */ 6597 static inline struct sk_buff *ieee80211_tx_dequeue_ni(struct ieee80211_hw *hw, 6598 struct ieee80211_txq *txq) 6599 { 6600 struct sk_buff *skb; 6601 6602 local_bh_disable(); 6603 skb = ieee80211_tx_dequeue(hw, txq); 6604 local_bh_enable(); 6605 6606 return skb; 6607 } 6608 6609 /** 6610 * ieee80211_next_txq - get next tx queue to pull packets from 6611 * 6612 * @hw: pointer as obtained from ieee80211_alloc_hw() 6613 * @ac: AC number to return packets from. 6614 * 6615 * Returns the next txq if successful, %NULL if no queue is eligible. If a txq 6616 * is returned, it should be returned with ieee80211_return_txq() after the 6617 * driver has finished scheduling it. 6618 */ 6619 struct ieee80211_txq *ieee80211_next_txq(struct ieee80211_hw *hw, u8 ac); 6620 6621 /** 6622 * ieee80211_txq_schedule_start - start new scheduling round for TXQs 6623 * 6624 * @hw: pointer as obtained from ieee80211_alloc_hw() 6625 * @ac: AC number to acquire locks for 6626 * 6627 * Should be called before ieee80211_next_txq() or ieee80211_return_txq(). 6628 * The driver must not call multiple TXQ scheduling rounds concurrently. 6629 */ 6630 void ieee80211_txq_schedule_start(struct ieee80211_hw *hw, u8 ac); 6631 6632 /* (deprecated) */ 6633 static inline void ieee80211_txq_schedule_end(struct ieee80211_hw *hw, u8 ac) 6634 { 6635 } 6636 6637 /** 6638 * ieee80211_schedule_txq - schedule a TXQ for transmission 6639 * 6640 * @hw: pointer as obtained from ieee80211_alloc_hw() 6641 * @txq: pointer obtained from station or virtual interface 6642 * 6643 * Schedules a TXQ for transmission if it is not already scheduled, 6644 * even if mac80211 does not have any packets buffered. 6645 * 6646 * The driver may call this function if it has buffered packets for 6647 * this TXQ internally. 6648 */ 6649 void ieee80211_schedule_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq); 6650 6651 /** 6652 * ieee80211_return_txq - return a TXQ previously acquired by ieee80211_next_txq() 6653 * 6654 * @hw: pointer as obtained from ieee80211_alloc_hw() 6655 * @txq: pointer obtained from station or virtual interface 6656 * @force: schedule txq even if mac80211 does not have any buffered packets. 6657 * 6658 * The driver may set force=true if it has buffered packets for this TXQ 6659 * internally. 6660 */ 6661 void ieee80211_return_txq(struct ieee80211_hw *hw, struct ieee80211_txq *txq, 6662 bool force); 6663 6664 /** 6665 * ieee80211_txq_may_transmit - check whether TXQ is allowed to transmit 6666 * 6667 * This function is used to check whether given txq is allowed to transmit by 6668 * the airtime scheduler, and can be used by drivers to access the airtime 6669 * fairness accounting without going using the scheduling order enfored by 6670 * next_txq(). 6671 * 6672 * Returns %true if the airtime scheduler thinks the TXQ should be allowed to 6673 * transmit, and %false if it should be throttled. This function can also have 6674 * the side effect of rotating the TXQ in the scheduler rotation, which will 6675 * eventually bring the deficit to positive and allow the station to transmit 6676 * again. 6677 * 6678 * The API ieee80211_txq_may_transmit() also ensures that TXQ list will be 6679 * aligned against driver's own round-robin scheduler list. i.e it rotates 6680 * the TXQ list till it makes the requested node becomes the first entry 6681 * in TXQ list. Thus both the TXQ list and driver's list are in sync. If this 6682 * function returns %true, the driver is expected to schedule packets 6683 * for transmission, and then return the TXQ through ieee80211_return_txq(). 6684 * 6685 * @hw: pointer as obtained from ieee80211_alloc_hw() 6686 * @txq: pointer obtained from station or virtual interface 6687 */ 6688 bool ieee80211_txq_may_transmit(struct ieee80211_hw *hw, 6689 struct ieee80211_txq *txq); 6690 6691 /** 6692 * ieee80211_txq_get_depth - get pending frame/byte count of given txq 6693 * 6694 * The values are not guaranteed to be coherent with regard to each other, i.e. 6695 * txq state can change half-way of this function and the caller may end up 6696 * with "new" frame_cnt and "old" byte_cnt or vice-versa. 6697 * 6698 * @txq: pointer obtained from station or virtual interface 6699 * @frame_cnt: pointer to store frame count 6700 * @byte_cnt: pointer to store byte count 6701 */ 6702 void ieee80211_txq_get_depth(struct ieee80211_txq *txq, 6703 unsigned long *frame_cnt, 6704 unsigned long *byte_cnt); 6705 6706 /** 6707 * ieee80211_nan_func_terminated - notify about NAN function termination. 6708 * 6709 * This function is used to notify mac80211 about NAN function termination. 6710 * Note that this function can't be called from hard irq. 6711 * 6712 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6713 * @inst_id: the local instance id 6714 * @reason: termination reason (one of the NL80211_NAN_FUNC_TERM_REASON_*) 6715 * @gfp: allocation flags 6716 */ 6717 void ieee80211_nan_func_terminated(struct ieee80211_vif *vif, 6718 u8 inst_id, 6719 enum nl80211_nan_func_term_reason reason, 6720 gfp_t gfp); 6721 6722 /** 6723 * ieee80211_nan_func_match - notify about NAN function match event. 6724 * 6725 * This function is used to notify mac80211 about NAN function match. The 6726 * cookie inside the match struct will be assigned by mac80211. 6727 * Note that this function can't be called from hard irq. 6728 * 6729 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6730 * @match: match event information 6731 * @gfp: allocation flags 6732 */ 6733 void ieee80211_nan_func_match(struct ieee80211_vif *vif, 6734 struct cfg80211_nan_match_params *match, 6735 gfp_t gfp); 6736 6737 /** 6738 * ieee80211_calc_rx_airtime - calculate estimated transmission airtime for RX. 6739 * 6740 * This function calculates the estimated airtime usage of a frame based on the 6741 * rate information in the RX status struct and the frame length. 6742 * 6743 * @hw: pointer as obtained from ieee80211_alloc_hw() 6744 * @status: &struct ieee80211_rx_status containing the transmission rate 6745 * information. 6746 * @len: frame length in bytes 6747 */ 6748 u32 ieee80211_calc_rx_airtime(struct ieee80211_hw *hw, 6749 struct ieee80211_rx_status *status, 6750 int len); 6751 6752 /** 6753 * ieee80211_calc_tx_airtime - calculate estimated transmission airtime for TX. 6754 * 6755 * This function calculates the estimated airtime usage of a frame based on the 6756 * rate information in the TX info struct and the frame length. 6757 * 6758 * @hw: pointer as obtained from ieee80211_alloc_hw() 6759 * @info: &struct ieee80211_tx_info of the frame. 6760 * @len: frame length in bytes 6761 */ 6762 u32 ieee80211_calc_tx_airtime(struct ieee80211_hw *hw, 6763 struct ieee80211_tx_info *info, 6764 int len); 6765 /** 6766 * ieee80211_set_hw_80211_encap - enable hardware encapsulation offloading. 6767 * 6768 * This function is used to notify mac80211 that a vif can be passed raw 802.3 6769 * frames. The driver needs to then handle the 802.11 encapsulation inside the 6770 * hardware or firmware. 6771 * 6772 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6773 * @enable: indicate if the feature should be turned on or off 6774 */ 6775 bool ieee80211_set_hw_80211_encap(struct ieee80211_vif *vif, bool enable); 6776 6777 /** 6778 * ieee80211_get_fils_discovery_tmpl - Get FILS discovery template. 6779 * @hw: pointer obtained from ieee80211_alloc_hw(). 6780 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6781 * 6782 * The driver is responsible for freeing the returned skb. 6783 * 6784 * Return: FILS discovery template. %NULL on error. 6785 */ 6786 struct sk_buff *ieee80211_get_fils_discovery_tmpl(struct ieee80211_hw *hw, 6787 struct ieee80211_vif *vif); 6788 6789 /** 6790 * ieee80211_get_unsol_bcast_probe_resp_tmpl - Get unsolicited broadcast 6791 * probe response template. 6792 * @hw: pointer obtained from ieee80211_alloc_hw(). 6793 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6794 * 6795 * The driver is responsible for freeing the returned skb. 6796 * 6797 * Return: Unsolicited broadcast probe response template. %NULL on error. 6798 */ 6799 struct sk_buff * 6800 ieee80211_get_unsol_bcast_probe_resp_tmpl(struct ieee80211_hw *hw, 6801 struct ieee80211_vif *vif); 6802 6803 /** 6804 * ieeee80211_obss_color_collision_notify - notify userland about a BSS color 6805 * collision. 6806 * 6807 * @vif: &struct ieee80211_vif pointer from the add_interface callback. 6808 * @color_bitmap: a 64 bit bitmap representing the colors that the local BSS is 6809 * aware of. 6810 */ 6811 void 6812 ieeee80211_obss_color_collision_notify(struct ieee80211_vif *vif, 6813 u64 color_bitmap); 6814 6815 /** 6816 * ieee80211_is_tx_data - check if frame is a data frame 6817 * 6818 * The function is used to check if a frame is a data frame. Frames with 6819 * hardware encapsulation enabled are data frames. 6820 * 6821 * @skb: the frame to be transmitted. 6822 */ 6823 static inline bool ieee80211_is_tx_data(struct sk_buff *skb) 6824 { 6825 struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); 6826 struct ieee80211_hdr *hdr = (void *) skb->data; 6827 6828 return info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP || 6829 ieee80211_is_data(hdr->frame_control); 6830 } 6831 6832 #endif /* MAC80211_H */ 6833