1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * V4L2 sub-device support header. 4 * 5 * Copyright (C) 2008 Hans Verkuil <hverkuil@xs4all.nl> 6 */ 7 8 #ifndef _V4L2_SUBDEV_H 9 #define _V4L2_SUBDEV_H 10 11 #include <linux/types.h> 12 #include <linux/v4l2-subdev.h> 13 #include <media/media-entity.h> 14 #include <media/v4l2-async.h> 15 #include <media/v4l2-common.h> 16 #include <media/v4l2-dev.h> 17 #include <media/v4l2-fh.h> 18 #include <media/v4l2-mediabus.h> 19 20 /* generic v4l2_device notify callback notification values */ 21 #define V4L2_SUBDEV_IR_RX_NOTIFY _IOW('v', 0, u32) 22 #define V4L2_SUBDEV_IR_RX_FIFO_SERVICE_REQ 0x00000001 23 #define V4L2_SUBDEV_IR_RX_END_OF_RX_DETECTED 0x00000002 24 #define V4L2_SUBDEV_IR_RX_HW_FIFO_OVERRUN 0x00000004 25 #define V4L2_SUBDEV_IR_RX_SW_FIFO_OVERRUN 0x00000008 26 27 #define V4L2_SUBDEV_IR_TX_NOTIFY _IOW('v', 1, u32) 28 #define V4L2_SUBDEV_IR_TX_FIFO_SERVICE_REQ 0x00000001 29 30 #define V4L2_DEVICE_NOTIFY_EVENT _IOW('v', 2, struct v4l2_event) 31 32 struct v4l2_device; 33 struct v4l2_ctrl_handler; 34 struct v4l2_event; 35 struct v4l2_event_subscription; 36 struct v4l2_fh; 37 struct v4l2_subdev; 38 struct v4l2_subdev_fh; 39 struct tuner_setup; 40 struct v4l2_mbus_frame_desc; 41 42 /** 43 * struct v4l2_decode_vbi_line - used to decode_vbi_line 44 * 45 * @is_second_field: Set to 0 for the first (odd) field; 46 * set to 1 for the second (even) field. 47 * @p: Pointer to the sliced VBI data from the decoder. On exit, points to 48 * the start of the payload. 49 * @line: Line number of the sliced VBI data (1-23) 50 * @type: VBI service type (V4L2_SLICED_*). 0 if no service found 51 */ 52 struct v4l2_decode_vbi_line { 53 u32 is_second_field; 54 u8 *p; 55 u32 line; 56 u32 type; 57 }; 58 59 /* 60 * Sub-devices are devices that are connected somehow to the main bridge 61 * device. These devices are usually audio/video muxers/encoders/decoders or 62 * sensors and webcam controllers. 63 * 64 * Usually these devices are controlled through an i2c bus, but other buses 65 * may also be used. 66 * 67 * The v4l2_subdev struct provides a way of accessing these devices in a 68 * generic manner. Most operations that these sub-devices support fall in 69 * a few categories: core ops, audio ops, video ops and tuner ops. 70 * 71 * More categories can be added if needed, although this should remain a 72 * limited set (no more than approx. 8 categories). 73 * 74 * Each category has its own set of ops that subdev drivers can implement. 75 * 76 * A subdev driver can leave the pointer to the category ops NULL if 77 * it does not implement them (e.g. an audio subdev will generally not 78 * implement the video category ops). The exception is the core category: 79 * this must always be present. 80 * 81 * These ops are all used internally so it is no problem to change, remove 82 * or add ops or move ops from one to another category. Currently these 83 * ops are based on the original ioctls, but since ops are not limited to 84 * one argument there is room for improvement here once all i2c subdev 85 * drivers are converted to use these ops. 86 */ 87 88 /* 89 * Core ops: it is highly recommended to implement at least these ops: 90 * 91 * log_status 92 * g_register 93 * s_register 94 * 95 * This provides basic debugging support. 96 * 97 * The ioctl ops is meant for generic ioctl-like commands. Depending on 98 * the use-case it might be better to use subdev-specific ops (currently 99 * not yet implemented) since ops provide proper type-checking. 100 */ 101 102 /** 103 * enum v4l2_subdev_io_pin_bits - Subdevice external IO pin configuration 104 * bits 105 * 106 * @V4L2_SUBDEV_IO_PIN_DISABLE: disables a pin config. ENABLE assumed. 107 * @V4L2_SUBDEV_IO_PIN_OUTPUT: set it if pin is an output. 108 * @V4L2_SUBDEV_IO_PIN_INPUT: set it if pin is an input. 109 * @V4L2_SUBDEV_IO_PIN_SET_VALUE: to set the output value via 110 * &struct v4l2_subdev_io_pin_config->value. 111 * @V4L2_SUBDEV_IO_PIN_ACTIVE_LOW: pin active is bit 0. 112 * Otherwise, ACTIVE HIGH is assumed. 113 */ 114 enum v4l2_subdev_io_pin_bits { 115 V4L2_SUBDEV_IO_PIN_DISABLE = 0, 116 V4L2_SUBDEV_IO_PIN_OUTPUT = 1, 117 V4L2_SUBDEV_IO_PIN_INPUT = 2, 118 V4L2_SUBDEV_IO_PIN_SET_VALUE = 3, 119 V4L2_SUBDEV_IO_PIN_ACTIVE_LOW = 4, 120 }; 121 122 /** 123 * struct v4l2_subdev_io_pin_config - Subdevice external IO pin configuration 124 * 125 * @flags: bitmask with flags for this pin's config, whose bits are defined by 126 * &enum v4l2_subdev_io_pin_bits. 127 * @pin: Chip external IO pin to configure 128 * @function: Internal signal pad/function to route to IO pin 129 * @value: Initial value for pin - e.g. GPIO output value 130 * @strength: Pin drive strength 131 */ 132 struct v4l2_subdev_io_pin_config { 133 u32 flags; 134 u8 pin; 135 u8 function; 136 u8 value; 137 u8 strength; 138 }; 139 140 /** 141 * struct v4l2_subdev_core_ops - Define core ops callbacks for subdevs 142 * 143 * @log_status: callback for VIDIOC_LOG_STATUS() ioctl handler code. 144 * 145 * @s_io_pin_config: configure one or more chip I/O pins for chips that 146 * multiplex different internal signal pads out to IO pins. This function 147 * takes a pointer to an array of 'n' pin configuration entries, one for 148 * each pin being configured. This function could be called at times 149 * other than just subdevice initialization. 150 * 151 * @init: initialize the sensor registers to some sort of reasonable default 152 * values. Do not use for new drivers and should be removed in existing 153 * drivers. 154 * 155 * @load_fw: load firmware. 156 * 157 * @reset: generic reset command. The argument selects which subsystems to 158 * reset. Passing 0 will always reset the whole chip. Do not use for new 159 * drivers without discussing this first on the linux-media mailinglist. 160 * There should be no reason normally to reset a device. 161 * 162 * @s_gpio: set GPIO pins. Very simple right now, might need to be extended with 163 * a direction argument if needed. 164 * 165 * @ioctl: called at the end of ioctl() syscall handler at the V4L2 core. 166 * used to provide support for private ioctls used on the driver. 167 * 168 * @compat_ioctl32: called when a 32 bits application uses a 64 bits Kernel, 169 * in order to fix data passed from/to userspace. 170 * 171 * @g_register: callback for VIDIOC_DBG_G_REGISTER() ioctl handler code. 172 * 173 * @s_register: callback for VIDIOC_DBG_S_REGISTER() ioctl handler code. 174 * 175 * @s_power: puts subdevice in power saving mode (on == 0) or normal operation 176 * mode (on == 1). 177 * 178 * @interrupt_service_routine: Called by the bridge chip's interrupt service 179 * handler, when an interrupt status has be raised due to this subdev, 180 * so that this subdev can handle the details. It may schedule work to be 181 * performed later. It must not sleep. **Called from an IRQ context**. 182 * 183 * @subscribe_event: used by the drivers to request the control framework that 184 * for it to be warned when the value of a control changes. 185 * 186 * @unsubscribe_event: remove event subscription from the control framework. 187 */ 188 struct v4l2_subdev_core_ops { 189 int (*log_status)(struct v4l2_subdev *sd); 190 int (*s_io_pin_config)(struct v4l2_subdev *sd, size_t n, 191 struct v4l2_subdev_io_pin_config *pincfg); 192 int (*init)(struct v4l2_subdev *sd, u32 val); 193 int (*load_fw)(struct v4l2_subdev *sd); 194 int (*reset)(struct v4l2_subdev *sd, u32 val); 195 int (*s_gpio)(struct v4l2_subdev *sd, u32 val); 196 long (*ioctl)(struct v4l2_subdev *sd, unsigned int cmd, void *arg); 197 #ifdef CONFIG_COMPAT 198 long (*compat_ioctl32)(struct v4l2_subdev *sd, unsigned int cmd, 199 unsigned long arg); 200 #endif 201 #ifdef CONFIG_VIDEO_ADV_DEBUG 202 int (*g_register)(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg); 203 int (*s_register)(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg); 204 #endif 205 int (*s_power)(struct v4l2_subdev *sd, int on); 206 int (*interrupt_service_routine)(struct v4l2_subdev *sd, 207 u32 status, bool *handled); 208 int (*subscribe_event)(struct v4l2_subdev *sd, struct v4l2_fh *fh, 209 struct v4l2_event_subscription *sub); 210 int (*unsubscribe_event)(struct v4l2_subdev *sd, struct v4l2_fh *fh, 211 struct v4l2_event_subscription *sub); 212 }; 213 214 /** 215 * struct v4l2_subdev_tuner_ops - Callbacks used when v4l device was opened 216 * in radio mode. 217 * 218 * @standby: puts the tuner in standby mode. It will be woken up 219 * automatically the next time it is used. 220 * 221 * @s_radio: callback that switches the tuner to radio mode. 222 * drivers should explicitly call it when a tuner ops should 223 * operate on radio mode, before being able to handle it. 224 * Used on devices that have both AM/FM radio receiver and TV. 225 * 226 * @s_frequency: callback for VIDIOC_S_FREQUENCY() ioctl handler code. 227 * 228 * @g_frequency: callback for VIDIOC_G_FREQUENCY() ioctl handler code. 229 * freq->type must be filled in. Normally done by video_ioctl2() 230 * or the bridge driver. 231 * 232 * @enum_freq_bands: callback for VIDIOC_ENUM_FREQ_BANDS() ioctl handler code. 233 * 234 * @g_tuner: callback for VIDIOC_G_TUNER() ioctl handler code. 235 * 236 * @s_tuner: callback for VIDIOC_S_TUNER() ioctl handler code. @vt->type must be 237 * filled in. Normally done by video_ioctl2 or the 238 * bridge driver. 239 * 240 * @g_modulator: callback for VIDIOC_G_MODULATOR() ioctl handler code. 241 * 242 * @s_modulator: callback for VIDIOC_S_MODULATOR() ioctl handler code. 243 * 244 * @s_type_addr: sets tuner type and its I2C addr. 245 * 246 * @s_config: sets tda9887 specific stuff, like port1, port2 and qss 247 * 248 * .. note:: 249 * 250 * On devices that have both AM/FM and TV, it is up to the driver 251 * to explicitly call s_radio when the tuner should be switched to 252 * radio mode, before handling other &struct v4l2_subdev_tuner_ops 253 * that would require it. An example of such usage is:: 254 * 255 * static void s_frequency(void *priv, const struct v4l2_frequency *f) 256 * { 257 * ... 258 * if (f.type == V4L2_TUNER_RADIO) 259 * v4l2_device_call_all(v4l2_dev, 0, tuner, s_radio); 260 * ... 261 * v4l2_device_call_all(v4l2_dev, 0, tuner, s_frequency); 262 * } 263 */ 264 struct v4l2_subdev_tuner_ops { 265 int (*standby)(struct v4l2_subdev *sd); 266 int (*s_radio)(struct v4l2_subdev *sd); 267 int (*s_frequency)(struct v4l2_subdev *sd, const struct v4l2_frequency *freq); 268 int (*g_frequency)(struct v4l2_subdev *sd, struct v4l2_frequency *freq); 269 int (*enum_freq_bands)(struct v4l2_subdev *sd, struct v4l2_frequency_band *band); 270 int (*g_tuner)(struct v4l2_subdev *sd, struct v4l2_tuner *vt); 271 int (*s_tuner)(struct v4l2_subdev *sd, const struct v4l2_tuner *vt); 272 int (*g_modulator)(struct v4l2_subdev *sd, struct v4l2_modulator *vm); 273 int (*s_modulator)(struct v4l2_subdev *sd, const struct v4l2_modulator *vm); 274 int (*s_type_addr)(struct v4l2_subdev *sd, struct tuner_setup *type); 275 int (*s_config)(struct v4l2_subdev *sd, const struct v4l2_priv_tun_config *config); 276 }; 277 278 /** 279 * struct v4l2_subdev_audio_ops - Callbacks used for audio-related settings 280 * 281 * @s_clock_freq: set the frequency (in Hz) of the audio clock output. 282 * Used to slave an audio processor to the video decoder, ensuring that 283 * audio and video remain synchronized. Usual values for the frequency 284 * are 48000, 44100 or 32000 Hz. If the frequency is not supported, then 285 * -EINVAL is returned. 286 * 287 * @s_i2s_clock_freq: sets I2S speed in bps. This is used to provide a standard 288 * way to select I2S clock used by driving digital audio streams at some 289 * board designs. Usual values for the frequency are 1024000 and 2048000. 290 * If the frequency is not supported, then %-EINVAL is returned. 291 * 292 * @s_routing: used to define the input and/or output pins of an audio chip, 293 * and any additional configuration data. 294 * Never attempt to use user-level input IDs (e.g. Composite, S-Video, 295 * Tuner) at this level. An i2c device shouldn't know about whether an 296 * input pin is connected to a Composite connector, become on another 297 * board or platform it might be connected to something else entirely. 298 * The calling driver is responsible for mapping a user-level input to 299 * the right pins on the i2c device. 300 * 301 * @s_stream: used to notify the audio code that stream will start or has 302 * stopped. 303 */ 304 struct v4l2_subdev_audio_ops { 305 int (*s_clock_freq)(struct v4l2_subdev *sd, u32 freq); 306 int (*s_i2s_clock_freq)(struct v4l2_subdev *sd, u32 freq); 307 int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config); 308 int (*s_stream)(struct v4l2_subdev *sd, int enable); 309 }; 310 311 /** 312 * enum v4l2_mbus_frame_desc_entry - media bus frame description flags 313 * 314 * @V4L2_MBUS_FRAME_DESC_FL_LEN_MAX: 315 * Indicates that &struct v4l2_mbus_frame_desc_entry->length field 316 * specifies maximum data length. 317 * @V4L2_MBUS_FRAME_DESC_FL_BLOB: 318 * Indicates that the format does not have line offsets, i.e. 319 * the receiver should use 1D DMA. 320 */ 321 enum v4l2_mbus_frame_desc_flags { 322 V4L2_MBUS_FRAME_DESC_FL_LEN_MAX = BIT(0), 323 V4L2_MBUS_FRAME_DESC_FL_BLOB = BIT(1), 324 }; 325 326 /** 327 * struct v4l2_mbus_frame_desc_entry - media bus frame description structure 328 * 329 * @flags: bitmask flags, as defined by &enum v4l2_mbus_frame_desc_flags. 330 * @pixelcode: media bus pixel code, valid if @flags 331 * %FRAME_DESC_FL_BLOB is not set. 332 * @length: number of octets per frame, valid if @flags 333 * %V4L2_MBUS_FRAME_DESC_FL_LEN_MAX is set. 334 */ 335 struct v4l2_mbus_frame_desc_entry { 336 enum v4l2_mbus_frame_desc_flags flags; 337 u32 pixelcode; 338 u32 length; 339 }; 340 341 #define V4L2_FRAME_DESC_ENTRY_MAX 4 342 343 /** 344 * struct v4l2_mbus_frame_desc - media bus data frame description 345 * @entry: frame descriptors array 346 * @num_entries: number of entries in @entry array 347 */ 348 struct v4l2_mbus_frame_desc { 349 struct v4l2_mbus_frame_desc_entry entry[V4L2_FRAME_DESC_ENTRY_MAX]; 350 unsigned short num_entries; 351 }; 352 353 /** 354 * struct v4l2_subdev_video_ops - Callbacks used when v4l device was opened 355 * in video mode. 356 * 357 * @s_routing: see s_routing in audio_ops, except this version is for video 358 * devices. 359 * 360 * @s_crystal_freq: sets the frequency of the crystal used to generate the 361 * clocks in Hz. An extra flags field allows device specific configuration 362 * regarding clock frequency dividers, etc. If not used, then set flags 363 * to 0. If the frequency is not supported, then -EINVAL is returned. 364 * 365 * @g_std: callback for VIDIOC_G_STD() ioctl handler code. 366 * 367 * @s_std: callback for VIDIOC_S_STD() ioctl handler code. 368 * 369 * @s_std_output: set v4l2_std_id for video OUTPUT devices. This is ignored by 370 * video input devices. 371 * 372 * @g_std_output: get current standard for video OUTPUT devices. This is ignored 373 * by video input devices. 374 * 375 * @querystd: callback for VIDIOC_QUERYSTD() ioctl handler code. 376 * 377 * @g_tvnorms: get &v4l2_std_id with all standards supported by the video 378 * CAPTURE device. This is ignored by video output devices. 379 * 380 * @g_tvnorms_output: get v4l2_std_id with all standards supported by the video 381 * OUTPUT device. This is ignored by video capture devices. 382 * 383 * @g_input_status: get input status. Same as the status field in the 384 * &struct &v4l2_input 385 * 386 * @s_stream: used to notify the driver that a video stream will start or has 387 * stopped. 388 * 389 * @g_pixelaspect: callback to return the pixelaspect ratio. 390 * 391 * @g_frame_interval: callback for VIDIOC_SUBDEV_G_FRAME_INTERVAL() 392 * ioctl handler code. 393 * 394 * @s_frame_interval: callback for VIDIOC_SUBDEV_S_FRAME_INTERVAL() 395 * ioctl handler code. 396 * 397 * @s_dv_timings: Set custom dv timings in the sub device. This is used 398 * when sub device is capable of setting detailed timing information 399 * in the hardware to generate/detect the video signal. 400 * 401 * @g_dv_timings: Get custom dv timings in the sub device. 402 * 403 * @query_dv_timings: callback for VIDIOC_QUERY_DV_TIMINGS() ioctl handler code. 404 * 405 * @g_mbus_config: get supported mediabus configurations 406 * 407 * @s_mbus_config: set a certain mediabus configuration. This operation is added 408 * for compatibility with soc-camera drivers and should not be used by new 409 * software. 410 * 411 * @s_rx_buffer: set a host allocated memory buffer for the subdev. The subdev 412 * can adjust @size to a lower value and must not write more data to the 413 * buffer starting at @data than the original value of @size. 414 */ 415 struct v4l2_subdev_video_ops { 416 int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config); 417 int (*s_crystal_freq)(struct v4l2_subdev *sd, u32 freq, u32 flags); 418 int (*g_std)(struct v4l2_subdev *sd, v4l2_std_id *norm); 419 int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm); 420 int (*s_std_output)(struct v4l2_subdev *sd, v4l2_std_id std); 421 int (*g_std_output)(struct v4l2_subdev *sd, v4l2_std_id *std); 422 int (*querystd)(struct v4l2_subdev *sd, v4l2_std_id *std); 423 int (*g_tvnorms)(struct v4l2_subdev *sd, v4l2_std_id *std); 424 int (*g_tvnorms_output)(struct v4l2_subdev *sd, v4l2_std_id *std); 425 int (*g_input_status)(struct v4l2_subdev *sd, u32 *status); 426 int (*s_stream)(struct v4l2_subdev *sd, int enable); 427 int (*g_pixelaspect)(struct v4l2_subdev *sd, struct v4l2_fract *aspect); 428 int (*g_frame_interval)(struct v4l2_subdev *sd, 429 struct v4l2_subdev_frame_interval *interval); 430 int (*s_frame_interval)(struct v4l2_subdev *sd, 431 struct v4l2_subdev_frame_interval *interval); 432 int (*s_dv_timings)(struct v4l2_subdev *sd, 433 struct v4l2_dv_timings *timings); 434 int (*g_dv_timings)(struct v4l2_subdev *sd, 435 struct v4l2_dv_timings *timings); 436 int (*query_dv_timings)(struct v4l2_subdev *sd, 437 struct v4l2_dv_timings *timings); 438 int (*g_mbus_config)(struct v4l2_subdev *sd, 439 struct v4l2_mbus_config *cfg); 440 int (*s_mbus_config)(struct v4l2_subdev *sd, 441 const struct v4l2_mbus_config *cfg); 442 int (*s_rx_buffer)(struct v4l2_subdev *sd, void *buf, 443 unsigned int *size); 444 }; 445 446 /** 447 * struct v4l2_subdev_vbi_ops - Callbacks used when v4l device was opened 448 * in video mode via the vbi device node. 449 * 450 * @decode_vbi_line: video decoders that support sliced VBI need to implement 451 * this ioctl. Field p of the &struct v4l2_decode_vbi_line is set to the 452 * start of the VBI data that was generated by the decoder. The driver 453 * then parses the sliced VBI data and sets the other fields in the 454 * struct accordingly. The pointer p is updated to point to the start of 455 * the payload which can be copied verbatim into the data field of the 456 * &struct v4l2_sliced_vbi_data. If no valid VBI data was found, then the 457 * type field is set to 0 on return. 458 * 459 * @s_vbi_data: used to generate VBI signals on a video signal. 460 * &struct v4l2_sliced_vbi_data is filled with the data packets that 461 * should be output. Note that if you set the line field to 0, then that 462 * VBI signal is disabled. If no valid VBI data was found, then the type 463 * field is set to 0 on return. 464 * 465 * @g_vbi_data: used to obtain the sliced VBI packet from a readback register. 466 * Not all video decoders support this. If no data is available because 467 * the readback register contains invalid or erroneous data %-EIO is 468 * returned. Note that you must fill in the 'id' member and the 'field' 469 * member (to determine whether CC data from the first or second field 470 * should be obtained). 471 * 472 * @g_sliced_vbi_cap: callback for VIDIOC_G_SLICED_VBI_CAP() ioctl handler 473 * code. 474 * 475 * @s_raw_fmt: setup the video encoder/decoder for raw VBI. 476 * 477 * @g_sliced_fmt: retrieve the current sliced VBI settings. 478 * 479 * @s_sliced_fmt: setup the sliced VBI settings. 480 */ 481 struct v4l2_subdev_vbi_ops { 482 int (*decode_vbi_line)(struct v4l2_subdev *sd, struct v4l2_decode_vbi_line *vbi_line); 483 int (*s_vbi_data)(struct v4l2_subdev *sd, const struct v4l2_sliced_vbi_data *vbi_data); 484 int (*g_vbi_data)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_data *vbi_data); 485 int (*g_sliced_vbi_cap)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_cap *cap); 486 int (*s_raw_fmt)(struct v4l2_subdev *sd, struct v4l2_vbi_format *fmt); 487 int (*g_sliced_fmt)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_format *fmt); 488 int (*s_sliced_fmt)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_format *fmt); 489 }; 490 491 /** 492 * struct v4l2_subdev_sensor_ops - v4l2-subdev sensor operations 493 * @g_skip_top_lines: number of lines at the top of the image to be skipped. 494 * This is needed for some sensors, which always corrupt 495 * several top lines of the output image, or which send their 496 * metadata in them. 497 * @g_skip_frames: number of frames to skip at stream start. This is needed for 498 * buggy sensors that generate faulty frames when they are 499 * turned on. 500 */ 501 struct v4l2_subdev_sensor_ops { 502 int (*g_skip_top_lines)(struct v4l2_subdev *sd, u32 *lines); 503 int (*g_skip_frames)(struct v4l2_subdev *sd, u32 *frames); 504 }; 505 506 /** 507 * enum v4l2_subdev_ir_mode- describes the type of IR supported 508 * 509 * @V4L2_SUBDEV_IR_MODE_PULSE_WIDTH: IR uses struct ir_raw_event records 510 */ 511 enum v4l2_subdev_ir_mode { 512 V4L2_SUBDEV_IR_MODE_PULSE_WIDTH, 513 }; 514 515 /** 516 * struct v4l2_subdev_ir_parameters - Parameters for IR TX or TX 517 * 518 * @bytes_per_data_element: bytes per data element of data in read or 519 * write call. 520 * @mode: IR mode as defined by &enum v4l2_subdev_ir_mode. 521 * @enable: device is active if true 522 * @interrupt_enable: IR interrupts are enabled if true 523 * @shutdown: if true: set hardware to low/no power, false: normal mode 524 * 525 * @modulation: if true, it uses carrier, if false: baseband 526 * @max_pulse_width: maximum pulse width in ns, valid only for baseband signal 527 * @carrier_freq: carrier frequency in Hz, valid only for modulated signal 528 * @duty_cycle: duty cycle percentage, valid only for modulated signal 529 * @invert_level: invert signal level 530 * 531 * @invert_carrier_sense: Send 0/space as a carrier burst. used only in TX. 532 * 533 * @noise_filter_min_width: min time of a valid pulse, in ns. Used only for RX. 534 * @carrier_range_lower: Lower carrier range, in Hz, valid only for modulated 535 * signal. Used only for RX. 536 * @carrier_range_upper: Upper carrier range, in Hz, valid only for modulated 537 * signal. Used only for RX. 538 * @resolution: The receive resolution, in ns . Used only for RX. 539 */ 540 struct v4l2_subdev_ir_parameters { 541 unsigned int bytes_per_data_element; 542 enum v4l2_subdev_ir_mode mode; 543 544 bool enable; 545 bool interrupt_enable; 546 bool shutdown; 547 548 bool modulation; 549 u32 max_pulse_width; 550 unsigned int carrier_freq; 551 unsigned int duty_cycle; 552 bool invert_level; 553 554 /* Tx only */ 555 bool invert_carrier_sense; 556 557 /* Rx only */ 558 u32 noise_filter_min_width; 559 unsigned int carrier_range_lower; 560 unsigned int carrier_range_upper; 561 u32 resolution; 562 }; 563 564 /** 565 * struct v4l2_subdev_ir_ops - operations for IR subdevices 566 * 567 * @rx_read: Reads received codes or pulse width data. 568 * The semantics are similar to a non-blocking read() call. 569 * @rx_g_parameters: Get the current operating parameters and state of the 570 * the IR receiver. 571 * @rx_s_parameters: Set the current operating parameters and state of the 572 * the IR receiver. It is recommended to call 573 * [rt]x_g_parameters first to fill out the current state, and only change 574 * the fields that need to be changed. Upon return, the actual device 575 * operating parameters and state will be returned. Note that hardware 576 * limitations may prevent the actual settings from matching the requested 577 * settings - e.g. an actual carrier setting of 35,904 Hz when 36,000 Hz 578 * was requested. An exception is when the shutdown parameter is true. 579 * The last used operational parameters will be returned, but the actual 580 * state of the hardware be different to minimize power consumption and 581 * processing when shutdown is true. 582 * 583 * @tx_write: Writes codes or pulse width data for transmission. 584 * The semantics are similar to a non-blocking write() call. 585 * @tx_g_parameters: Get the current operating parameters and state of the 586 * the IR transmitter. 587 * @tx_s_parameters: Set the current operating parameters and state of the 588 * the IR transmitter. It is recommended to call 589 * [rt]x_g_parameters first to fill out the current state, and only change 590 * the fields that need to be changed. Upon return, the actual device 591 * operating parameters and state will be returned. Note that hardware 592 * limitations may prevent the actual settings from matching the requested 593 * settings - e.g. an actual carrier setting of 35,904 Hz when 36,000 Hz 594 * was requested. An exception is when the shutdown parameter is true. 595 * The last used operational parameters will be returned, but the actual 596 * state of the hardware be different to minimize power consumption and 597 * processing when shutdown is true. 598 */ 599 struct v4l2_subdev_ir_ops { 600 /* Receiver */ 601 int (*rx_read)(struct v4l2_subdev *sd, u8 *buf, size_t count, 602 ssize_t *num); 603 604 int (*rx_g_parameters)(struct v4l2_subdev *sd, 605 struct v4l2_subdev_ir_parameters *params); 606 int (*rx_s_parameters)(struct v4l2_subdev *sd, 607 struct v4l2_subdev_ir_parameters *params); 608 609 /* Transmitter */ 610 int (*tx_write)(struct v4l2_subdev *sd, u8 *buf, size_t count, 611 ssize_t *num); 612 613 int (*tx_g_parameters)(struct v4l2_subdev *sd, 614 struct v4l2_subdev_ir_parameters *params); 615 int (*tx_s_parameters)(struct v4l2_subdev *sd, 616 struct v4l2_subdev_ir_parameters *params); 617 }; 618 619 /** 620 * struct v4l2_subdev_pad_config - Used for storing subdev pad information. 621 * 622 * @try_fmt: &struct v4l2_mbus_framefmt 623 * @try_crop: &struct v4l2_rect to be used for crop 624 * @try_compose: &struct v4l2_rect to be used for compose 625 * 626 * This structure only needs to be passed to the pad op if the 'which' field 627 * of the main argument is set to %V4L2_SUBDEV_FORMAT_TRY. For 628 * %V4L2_SUBDEV_FORMAT_ACTIVE it is safe to pass %NULL. 629 */ 630 struct v4l2_subdev_pad_config { 631 struct v4l2_mbus_framefmt try_fmt; 632 struct v4l2_rect try_crop; 633 struct v4l2_rect try_compose; 634 }; 635 636 /** 637 * struct v4l2_subdev_pad_ops - v4l2-subdev pad level operations 638 * 639 * @init_cfg: initialize the pad config to default values 640 * @enum_mbus_code: callback for VIDIOC_SUBDEV_ENUM_MBUS_CODE() ioctl handler 641 * code. 642 * @enum_frame_size: callback for VIDIOC_SUBDEV_ENUM_FRAME_SIZE() ioctl handler 643 * code. 644 * 645 * @enum_frame_interval: callback for VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL() ioctl 646 * handler code. 647 * 648 * @get_fmt: callback for VIDIOC_SUBDEV_G_FMT() ioctl handler code. 649 * 650 * @set_fmt: callback for VIDIOC_SUBDEV_S_FMT() ioctl handler code. 651 * 652 * @get_selection: callback for VIDIOC_SUBDEV_G_SELECTION() ioctl handler code. 653 * 654 * @set_selection: callback for VIDIOC_SUBDEV_S_SELECTION() ioctl handler code. 655 * 656 * @get_edid: callback for VIDIOC_SUBDEV_G_EDID() ioctl handler code. 657 * 658 * @set_edid: callback for VIDIOC_SUBDEV_S_EDID() ioctl handler code. 659 * 660 * @dv_timings_cap: callback for VIDIOC_SUBDEV_DV_TIMINGS_CAP() ioctl handler 661 * code. 662 * 663 * @enum_dv_timings: callback for VIDIOC_SUBDEV_ENUM_DV_TIMINGS() ioctl handler 664 * code. 665 * 666 * @link_validate: used by the media controller code to check if the links 667 * that belongs to a pipeline can be used for stream. 668 * 669 * @get_frame_desc: get the current low level media bus frame parameters. 670 * 671 * @set_frame_desc: set the low level media bus frame parameters, @fd array 672 * may be adjusted by the subdev driver to device capabilities. 673 */ 674 struct v4l2_subdev_pad_ops { 675 int (*init_cfg)(struct v4l2_subdev *sd, 676 struct v4l2_subdev_pad_config *cfg); 677 int (*enum_mbus_code)(struct v4l2_subdev *sd, 678 struct v4l2_subdev_pad_config *cfg, 679 struct v4l2_subdev_mbus_code_enum *code); 680 int (*enum_frame_size)(struct v4l2_subdev *sd, 681 struct v4l2_subdev_pad_config *cfg, 682 struct v4l2_subdev_frame_size_enum *fse); 683 int (*enum_frame_interval)(struct v4l2_subdev *sd, 684 struct v4l2_subdev_pad_config *cfg, 685 struct v4l2_subdev_frame_interval_enum *fie); 686 int (*get_fmt)(struct v4l2_subdev *sd, 687 struct v4l2_subdev_pad_config *cfg, 688 struct v4l2_subdev_format *format); 689 int (*set_fmt)(struct v4l2_subdev *sd, 690 struct v4l2_subdev_pad_config *cfg, 691 struct v4l2_subdev_format *format); 692 int (*get_selection)(struct v4l2_subdev *sd, 693 struct v4l2_subdev_pad_config *cfg, 694 struct v4l2_subdev_selection *sel); 695 int (*set_selection)(struct v4l2_subdev *sd, 696 struct v4l2_subdev_pad_config *cfg, 697 struct v4l2_subdev_selection *sel); 698 int (*get_edid)(struct v4l2_subdev *sd, struct v4l2_edid *edid); 699 int (*set_edid)(struct v4l2_subdev *sd, struct v4l2_edid *edid); 700 int (*dv_timings_cap)(struct v4l2_subdev *sd, 701 struct v4l2_dv_timings_cap *cap); 702 int (*enum_dv_timings)(struct v4l2_subdev *sd, 703 struct v4l2_enum_dv_timings *timings); 704 #ifdef CONFIG_MEDIA_CONTROLLER 705 int (*link_validate)(struct v4l2_subdev *sd, struct media_link *link, 706 struct v4l2_subdev_format *source_fmt, 707 struct v4l2_subdev_format *sink_fmt); 708 #endif /* CONFIG_MEDIA_CONTROLLER */ 709 int (*get_frame_desc)(struct v4l2_subdev *sd, unsigned int pad, 710 struct v4l2_mbus_frame_desc *fd); 711 int (*set_frame_desc)(struct v4l2_subdev *sd, unsigned int pad, 712 struct v4l2_mbus_frame_desc *fd); 713 }; 714 715 /** 716 * struct v4l2_subdev_ops - Subdev operations 717 * 718 * @core: pointer to &struct v4l2_subdev_core_ops. Can be %NULL 719 * @tuner: pointer to &struct v4l2_subdev_tuner_ops. Can be %NULL 720 * @audio: pointer to &struct v4l2_subdev_audio_ops. Can be %NULL 721 * @video: pointer to &struct v4l2_subdev_video_ops. Can be %NULL 722 * @vbi: pointer to &struct v4l2_subdev_vbi_ops. Can be %NULL 723 * @ir: pointer to &struct v4l2_subdev_ir_ops. Can be %NULL 724 * @sensor: pointer to &struct v4l2_subdev_sensor_ops. Can be %NULL 725 * @pad: pointer to &struct v4l2_subdev_pad_ops. Can be %NULL 726 */ 727 struct v4l2_subdev_ops { 728 const struct v4l2_subdev_core_ops *core; 729 const struct v4l2_subdev_tuner_ops *tuner; 730 const struct v4l2_subdev_audio_ops *audio; 731 const struct v4l2_subdev_video_ops *video; 732 const struct v4l2_subdev_vbi_ops *vbi; 733 const struct v4l2_subdev_ir_ops *ir; 734 const struct v4l2_subdev_sensor_ops *sensor; 735 const struct v4l2_subdev_pad_ops *pad; 736 }; 737 738 /** 739 * struct v4l2_subdev_internal_ops - V4L2 subdev internal ops 740 * 741 * @registered: called when this subdev is registered. When called the v4l2_dev 742 * field is set to the correct v4l2_device. 743 * 744 * @unregistered: called when this subdev is unregistered. When called the 745 * v4l2_dev field is still set to the correct v4l2_device. 746 * 747 * @open: called when the subdev device node is opened by an application. 748 * 749 * @close: called when the subdev device node is closed. Please note that 750 * it is possible for @close to be called after @unregistered! 751 * 752 * @release: called when the last user of the subdev device is gone. This 753 * happens after the @unregistered callback and when the last open 754 * filehandle to the v4l-subdevX device node was closed. If no device 755 * node was created for this sub-device, then the @release callback 756 * is called right after the @unregistered callback. 757 * The @release callback is typically used to free the memory containing 758 * the v4l2_subdev structure. It is almost certainly required for any 759 * sub-device that sets the V4L2_SUBDEV_FL_HAS_DEVNODE flag. 760 * 761 * .. note:: 762 * Never call this from drivers, only the v4l2 framework can call 763 * these ops. 764 */ 765 struct v4l2_subdev_internal_ops { 766 int (*registered)(struct v4l2_subdev *sd); 767 void (*unregistered)(struct v4l2_subdev *sd); 768 int (*open)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh); 769 int (*close)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh); 770 void (*release)(struct v4l2_subdev *sd); 771 }; 772 773 #define V4L2_SUBDEV_NAME_SIZE 32 774 775 /* Set this flag if this subdev is a i2c device. */ 776 #define V4L2_SUBDEV_FL_IS_I2C (1U << 0) 777 /* Set this flag if this subdev is a spi device. */ 778 #define V4L2_SUBDEV_FL_IS_SPI (1U << 1) 779 /* Set this flag if this subdev needs a device node. */ 780 #define V4L2_SUBDEV_FL_HAS_DEVNODE (1U << 2) 781 /* 782 * Set this flag if this subdev generates events. 783 * Note controls can send events, thus drivers exposing controls 784 * should set this flag. 785 */ 786 #define V4L2_SUBDEV_FL_HAS_EVENTS (1U << 3) 787 788 struct regulator_bulk_data; 789 790 /** 791 * struct v4l2_subdev_platform_data - regulators config struct 792 * 793 * @regulators: Optional regulators used to power on/off the subdevice 794 * @num_regulators: Number of regululators 795 * @host_priv: Per-subdevice data, specific for a certain video host device 796 */ 797 struct v4l2_subdev_platform_data { 798 struct regulator_bulk_data *regulators; 799 int num_regulators; 800 801 void *host_priv; 802 }; 803 804 /** 805 * struct v4l2_subdev - describes a V4L2 sub-device 806 * 807 * @entity: pointer to &struct media_entity 808 * @list: List of sub-devices 809 * @owner: The owner is the same as the driver's &struct device owner. 810 * @owner_v4l2_dev: true if the &sd->owner matches the owner of @v4l2_dev->dev 811 * owner. Initialized by v4l2_device_register_subdev(). 812 * @flags: subdev flags. Can be: 813 * %V4L2_SUBDEV_FL_IS_I2C - Set this flag if this subdev is a i2c device; 814 * %V4L2_SUBDEV_FL_IS_SPI - Set this flag if this subdev is a spi device; 815 * %V4L2_SUBDEV_FL_HAS_DEVNODE - Set this flag if this subdev needs a 816 * device node; 817 * %V4L2_SUBDEV_FL_HAS_EVENTS - Set this flag if this subdev generates 818 * events. 819 * 820 * @v4l2_dev: pointer to struct &v4l2_device 821 * @ops: pointer to struct &v4l2_subdev_ops 822 * @internal_ops: pointer to struct &v4l2_subdev_internal_ops. 823 * Never call these internal ops from within a driver! 824 * @ctrl_handler: The control handler of this subdev. May be NULL. 825 * @name: Name of the sub-device. Please notice that the name must be unique. 826 * @grp_id: can be used to group similar subdevs. Value is driver-specific 827 * @dev_priv: pointer to private data 828 * @host_priv: pointer to private data used by the device where the subdev 829 * is attached. 830 * @devnode: subdev device node 831 * @dev: pointer to the physical device, if any 832 * @fwnode: The fwnode_handle of the subdev, usually the same as 833 * either dev->of_node->fwnode or dev->fwnode (whichever is non-NULL). 834 * @async_list: Links this subdev to a global subdev_list or @notifier->done 835 * list. 836 * @asd: Pointer to respective &struct v4l2_async_subdev. 837 * @notifier: Pointer to the managing notifier. 838 * @subdev_notifier: A sub-device notifier implicitly registered for the sub- 839 * device using v4l2_device_register_sensor_subdev(). 840 * @pdata: common part of subdevice platform data 841 * 842 * Each instance of a subdev driver should create this struct, either 843 * stand-alone or embedded in a larger struct. 844 * 845 * This structure should be initialized by v4l2_subdev_init() or one of 846 * its variants: v4l2_spi_subdev_init(), v4l2_i2c_subdev_init(). 847 */ 848 struct v4l2_subdev { 849 #if defined(CONFIG_MEDIA_CONTROLLER) 850 struct media_entity entity; 851 #endif 852 struct list_head list; 853 struct module *owner; 854 bool owner_v4l2_dev; 855 u32 flags; 856 struct v4l2_device *v4l2_dev; 857 const struct v4l2_subdev_ops *ops; 858 const struct v4l2_subdev_internal_ops *internal_ops; 859 struct v4l2_ctrl_handler *ctrl_handler; 860 char name[V4L2_SUBDEV_NAME_SIZE]; 861 u32 grp_id; 862 void *dev_priv; 863 void *host_priv; 864 struct video_device *devnode; 865 struct device *dev; 866 struct fwnode_handle *fwnode; 867 struct list_head async_list; 868 struct v4l2_async_subdev *asd; 869 struct v4l2_async_notifier *notifier; 870 struct v4l2_async_notifier *subdev_notifier; 871 struct v4l2_subdev_platform_data *pdata; 872 }; 873 874 875 /** 876 * media_entity_to_v4l2_subdev - Returns a &struct v4l2_subdev from 877 * the &struct media_entity embedded in it. 878 * 879 * @ent: pointer to &struct media_entity. 880 */ 881 #define media_entity_to_v4l2_subdev(ent) \ 882 ({ \ 883 typeof(ent) __me_sd_ent = (ent); \ 884 \ 885 __me_sd_ent ? \ 886 container_of(__me_sd_ent, struct v4l2_subdev, entity) : \ 887 NULL; \ 888 }) 889 890 /** 891 * vdev_to_v4l2_subdev - Returns a &struct v4l2_subdev from 892 * the &struct video_device embedded on it. 893 * 894 * @vdev: pointer to &struct video_device 895 */ 896 #define vdev_to_v4l2_subdev(vdev) \ 897 ((struct v4l2_subdev *)video_get_drvdata(vdev)) 898 899 /** 900 * struct v4l2_subdev_fh - Used for storing subdev information per file handle 901 * 902 * @vfh: pointer to &struct v4l2_fh 903 * @pad: pointer to &struct v4l2_subdev_pad_config 904 * @owner: module pointer to the owner of this file handle 905 */ 906 struct v4l2_subdev_fh { 907 struct v4l2_fh vfh; 908 struct module *owner; 909 #if defined(CONFIG_VIDEO_V4L2_SUBDEV_API) 910 struct v4l2_subdev_pad_config *pad; 911 #endif 912 }; 913 914 /** 915 * to_v4l2_subdev_fh - Returns a &struct v4l2_subdev_fh from 916 * the &struct v4l2_fh embedded on it. 917 * 918 * @fh: pointer to &struct v4l2_fh 919 */ 920 #define to_v4l2_subdev_fh(fh) \ 921 container_of(fh, struct v4l2_subdev_fh, vfh) 922 923 #if defined(CONFIG_VIDEO_V4L2_SUBDEV_API) 924 925 /** 926 * v4l2_subdev_get_try_format - ancillary routine to call 927 * &struct v4l2_subdev_pad_config->try_fmt 928 * 929 * @sd: pointer to &struct v4l2_subdev 930 * @cfg: pointer to &struct v4l2_subdev_pad_config array. 931 * @pad: index of the pad in the @cfg array. 932 */ 933 static inline struct v4l2_mbus_framefmt 934 *v4l2_subdev_get_try_format(struct v4l2_subdev *sd, 935 struct v4l2_subdev_pad_config *cfg, 936 unsigned int pad) 937 { 938 if (WARN_ON(pad >= sd->entity.num_pads)) 939 pad = 0; 940 return &cfg[pad].try_fmt; 941 } 942 943 /** 944 * v4l2_subdev_get_try_crop - ancillary routine to call 945 * &struct v4l2_subdev_pad_config->try_crop 946 * 947 * @sd: pointer to &struct v4l2_subdev 948 * @cfg: pointer to &struct v4l2_subdev_pad_config array. 949 * @pad: index of the pad in the @cfg array. 950 */ 951 static inline struct v4l2_rect 952 *v4l2_subdev_get_try_crop(struct v4l2_subdev *sd, 953 struct v4l2_subdev_pad_config *cfg, 954 unsigned int pad) 955 { 956 if (WARN_ON(pad >= sd->entity.num_pads)) 957 pad = 0; 958 return &cfg[pad].try_crop; 959 } 960 961 /** 962 * v4l2_subdev_get_try_crop - ancillary routine to call 963 * &struct v4l2_subdev_pad_config->try_compose 964 * 965 * @sd: pointer to &struct v4l2_subdev 966 * @cfg: pointer to &struct v4l2_subdev_pad_config array. 967 * @pad: index of the pad in the @cfg array. 968 */ 969 static inline struct v4l2_rect 970 *v4l2_subdev_get_try_compose(struct v4l2_subdev *sd, 971 struct v4l2_subdev_pad_config *cfg, 972 unsigned int pad) 973 { 974 if (WARN_ON(pad >= sd->entity.num_pads)) 975 pad = 0; 976 return &cfg[pad].try_compose; 977 } 978 #endif 979 980 extern const struct v4l2_file_operations v4l2_subdev_fops; 981 982 /** 983 * v4l2_set_subdevdata - Sets V4L2 dev private device data 984 * 985 * @sd: pointer to &struct v4l2_subdev 986 * @p: pointer to the private device data to be stored. 987 */ 988 static inline void v4l2_set_subdevdata(struct v4l2_subdev *sd, void *p) 989 { 990 sd->dev_priv = p; 991 } 992 993 /** 994 * v4l2_get_subdevdata - Gets V4L2 dev private device data 995 * 996 * @sd: pointer to &struct v4l2_subdev 997 * 998 * Returns the pointer to the private device data to be stored. 999 */ 1000 static inline void *v4l2_get_subdevdata(const struct v4l2_subdev *sd) 1001 { 1002 return sd->dev_priv; 1003 } 1004 1005 /** 1006 * v4l2_set_subdev_hostdata - Sets V4L2 dev private host data 1007 * 1008 * @sd: pointer to &struct v4l2_subdev 1009 * @p: pointer to the private data to be stored. 1010 */ 1011 static inline void v4l2_set_subdev_hostdata(struct v4l2_subdev *sd, void *p) 1012 { 1013 sd->host_priv = p; 1014 } 1015 1016 /** 1017 * v4l2_get_subdev_hostdata - Gets V4L2 dev private data 1018 * 1019 * @sd: pointer to &struct v4l2_subdev 1020 * 1021 * Returns the pointer to the private host data to be stored. 1022 */ 1023 static inline void *v4l2_get_subdev_hostdata(const struct v4l2_subdev *sd) 1024 { 1025 return sd->host_priv; 1026 } 1027 1028 #ifdef CONFIG_MEDIA_CONTROLLER 1029 1030 /** 1031 * v4l2_subdev_get_fwnode_pad_1_to_1 - Get pad number from a subdev fwnode 1032 * endpoint, assuming 1:1 port:pad 1033 * 1034 * @entity - Pointer to the subdev entity 1035 * @endpoint - Pointer to a parsed fwnode endpoint 1036 * 1037 * This function can be used as the .get_fwnode_pad operation for 1038 * subdevices that map port numbers and pad indexes 1:1. If the endpoint 1039 * is owned by the subdevice, the function returns the endpoint port 1040 * number. 1041 * 1042 * Returns the endpoint port number on success or a negative error code. 1043 */ 1044 int v4l2_subdev_get_fwnode_pad_1_to_1(struct media_entity *entity, 1045 struct fwnode_endpoint *endpoint); 1046 1047 /** 1048 * v4l2_subdev_link_validate_default - validates a media link 1049 * 1050 * @sd: pointer to &struct v4l2_subdev 1051 * @link: pointer to &struct media_link 1052 * @source_fmt: pointer to &struct v4l2_subdev_format 1053 * @sink_fmt: pointer to &struct v4l2_subdev_format 1054 * 1055 * This function ensures that width, height and the media bus pixel 1056 * code are equal on both source and sink of the link. 1057 */ 1058 int v4l2_subdev_link_validate_default(struct v4l2_subdev *sd, 1059 struct media_link *link, 1060 struct v4l2_subdev_format *source_fmt, 1061 struct v4l2_subdev_format *sink_fmt); 1062 1063 /** 1064 * v4l2_subdev_link_validate - validates a media link 1065 * 1066 * @link: pointer to &struct media_link 1067 * 1068 * This function calls the subdev's link_validate ops to validate 1069 * if a media link is valid for streaming. It also internally 1070 * calls v4l2_subdev_link_validate_default() to ensure that 1071 * width, height and the media bus pixel code are equal on both 1072 * source and sink of the link. 1073 */ 1074 int v4l2_subdev_link_validate(struct media_link *link); 1075 1076 /** 1077 * v4l2_subdev_alloc_pad_config - Allocates memory for pad config 1078 * 1079 * @sd: pointer to struct v4l2_subdev 1080 */ 1081 struct 1082 v4l2_subdev_pad_config *v4l2_subdev_alloc_pad_config(struct v4l2_subdev *sd); 1083 1084 /** 1085 * v4l2_subdev_free_pad_config - Frees memory allocated by 1086 * v4l2_subdev_alloc_pad_config(). 1087 * 1088 * @cfg: pointer to &struct v4l2_subdev_pad_config 1089 */ 1090 void v4l2_subdev_free_pad_config(struct v4l2_subdev_pad_config *cfg); 1091 #endif /* CONFIG_MEDIA_CONTROLLER */ 1092 1093 /** 1094 * v4l2_subdev_init - initializes the sub-device struct 1095 * 1096 * @sd: pointer to the &struct v4l2_subdev to be initialized 1097 * @ops: pointer to &struct v4l2_subdev_ops. 1098 */ 1099 void v4l2_subdev_init(struct v4l2_subdev *sd, 1100 const struct v4l2_subdev_ops *ops); 1101 1102 extern const struct v4l2_subdev_ops v4l2_subdev_call_wrappers; 1103 1104 /** 1105 * v4l2_subdev_call - call an operation of a v4l2_subdev. 1106 * 1107 * @sd: pointer to the &struct v4l2_subdev 1108 * @o: name of the element at &struct v4l2_subdev_ops that contains @f. 1109 * Each element there groups a set of callbacks functions. 1110 * @f: callback function to be called. 1111 * The callback functions are defined in groups, according to 1112 * each element at &struct v4l2_subdev_ops. 1113 * @args: arguments for @f. 1114 * 1115 * Example: err = v4l2_subdev_call(sd, video, s_std, norm); 1116 */ 1117 #define v4l2_subdev_call(sd, o, f, args...) \ 1118 ({ \ 1119 struct v4l2_subdev *__sd = (sd); \ 1120 int __result; \ 1121 if (!__sd) \ 1122 __result = -ENODEV; \ 1123 else if (!(__sd->ops->o && __sd->ops->o->f)) \ 1124 __result = -ENOIOCTLCMD; \ 1125 else if (v4l2_subdev_call_wrappers.o && \ 1126 v4l2_subdev_call_wrappers.o->f) \ 1127 __result = v4l2_subdev_call_wrappers.o->f( \ 1128 __sd, ##args); \ 1129 else \ 1130 __result = __sd->ops->o->f(__sd, ##args); \ 1131 __result; \ 1132 }) 1133 1134 /** 1135 * v4l2_subdev_has_op - Checks if a subdev defines a certain operation. 1136 * 1137 * @sd: pointer to the &struct v4l2_subdev 1138 * @o: The group of callback functions in &struct v4l2_subdev_ops 1139 * which @f is a part of. 1140 * @f: callback function to be checked for its existence. 1141 */ 1142 #define v4l2_subdev_has_op(sd, o, f) \ 1143 ((sd)->ops->o && (sd)->ops->o->f) 1144 1145 /** 1146 * v4l2_subdev_notify_event() - Delivers event notification for subdevice 1147 * @sd: The subdev for which to deliver the event 1148 * @ev: The event to deliver 1149 * 1150 * Will deliver the specified event to all userspace event listeners which are 1151 * subscribed to the v42l subdev event queue as well as to the bridge driver 1152 * using the notify callback. The notification type for the notify callback 1153 * will be %V4L2_DEVICE_NOTIFY_EVENT. 1154 */ 1155 void v4l2_subdev_notify_event(struct v4l2_subdev *sd, 1156 const struct v4l2_event *ev); 1157 1158 #endif 1159