1 /* 2 * NetChip 2280 high/full speed USB device controller. 3 * Unlike many such controllers, this one talks PCI. 4 */ 5 #ifndef __LINUX_USB_NET2280_H 6 #define __LINUX_USB_NET2280_H 7 8 /* 9 * Copyright (C) 2002 NetChip Technology, Inc. (http://www.netchip.com) 10 * Copyright (C) 2003 David Brownell 11 * 12 * This program is free software; you can redistribute it and/or modify 13 * it under the terms of the GNU General Public License as published by 14 * the Free Software Foundation; either version 2 of the License, or 15 * (at your option) any later version. 16 * 17 * This program is distributed in the hope that it will be useful, 18 * but WITHOUT ANY WARRANTY; without even the implied warranty of 19 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 20 * GNU General Public License for more details. 21 * 22 * You should have received a copy of the GNU General Public License 23 * along with this program; if not, write to the Free Software 24 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA 25 */ 26 27 /*-------------------------------------------------------------------------*/ 28 29 /* NET2280 MEMORY MAPPED REGISTERS 30 * 31 * The register layout came from the chip documentation, and the bit 32 * number definitions were extracted from chip specification. 33 * 34 * Use the shift operator ('<<') to build bit masks, with readl/writel 35 * to access the registers through PCI. 36 */ 37 38 /* main registers, BAR0 + 0x0000 */ 39 struct net2280_regs { 40 /* offset 0x0000 */ 41 u32 devinit; 42 #define LOCAL_CLOCK_FREQUENCY 8 43 #define FORCE_PCI_RESET 7 44 #define PCI_ID 6 45 #define PCI_ENABLE 5 46 #define FIFO_SOFT_RESET 4 47 #define CFG_SOFT_RESET 3 48 #define PCI_SOFT_RESET 2 49 #define USB_SOFT_RESET 1 50 #define M8051_RESET 0 51 u32 eectl; 52 #define EEPROM_ADDRESS_WIDTH 23 53 #define EEPROM_CHIP_SELECT_ACTIVE 22 54 #define EEPROM_PRESENT 21 55 #define EEPROM_VALID 20 56 #define EEPROM_BUSY 19 57 #define EEPROM_CHIP_SELECT_ENABLE 18 58 #define EEPROM_BYTE_READ_START 17 59 #define EEPROM_BYTE_WRITE_START 16 60 #define EEPROM_READ_DATA 8 61 #define EEPROM_WRITE_DATA 0 62 u32 eeclkfreq; 63 u32 _unused0; 64 /* offset 0x0010 */ 65 66 u32 pciirqenb0; /* interrupt PCI master ... */ 67 #define SETUP_PACKET_INTERRUPT_ENABLE 7 68 #define ENDPOINT_F_INTERRUPT_ENABLE 6 69 #define ENDPOINT_E_INTERRUPT_ENABLE 5 70 #define ENDPOINT_D_INTERRUPT_ENABLE 4 71 #define ENDPOINT_C_INTERRUPT_ENABLE 3 72 #define ENDPOINT_B_INTERRUPT_ENABLE 2 73 #define ENDPOINT_A_INTERRUPT_ENABLE 1 74 #define ENDPOINT_0_INTERRUPT_ENABLE 0 75 u32 pciirqenb1; 76 #define PCI_INTERRUPT_ENABLE 31 77 #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 78 #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 79 #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 80 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 81 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 82 #define PCI_TARGET_ABORT_ASSERTED_INTERRUPT_ENABLE 18 83 #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 84 #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 85 #define GPIO_INTERRUPT_ENABLE 13 86 #define DMA_D_INTERRUPT_ENABLE 12 87 #define DMA_C_INTERRUPT_ENABLE 11 88 #define DMA_B_INTERRUPT_ENABLE 10 89 #define DMA_A_INTERRUPT_ENABLE 9 90 #define EEPROM_DONE_INTERRUPT_ENABLE 8 91 #define VBUS_INTERRUPT_ENABLE 7 92 #define CONTROL_STATUS_INTERRUPT_ENABLE 6 93 #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 94 #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 95 #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 96 #define RESUME_INTERRUPT_ENABLE 1 97 #define SOF_INTERRUPT_ENABLE 0 98 u32 cpu_irqenb0; /* ... or onboard 8051 */ 99 #define SETUP_PACKET_INTERRUPT_ENABLE 7 100 #define ENDPOINT_F_INTERRUPT_ENABLE 6 101 #define ENDPOINT_E_INTERRUPT_ENABLE 5 102 #define ENDPOINT_D_INTERRUPT_ENABLE 4 103 #define ENDPOINT_C_INTERRUPT_ENABLE 3 104 #define ENDPOINT_B_INTERRUPT_ENABLE 2 105 #define ENDPOINT_A_INTERRUPT_ENABLE 1 106 #define ENDPOINT_0_INTERRUPT_ENABLE 0 107 u32 cpu_irqenb1; 108 #define CPU_INTERRUPT_ENABLE 31 109 #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 110 #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 111 #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 112 #define PCI_INTA_INTERRUPT_ENABLE 24 113 #define PCI_PME_INTERRUPT_ENABLE 23 114 #define PCI_SERR_INTERRUPT_ENABLE 22 115 #define PCI_PERR_INTERRUPT_ENABLE 21 116 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 117 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 118 #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 119 #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 120 #define GPIO_INTERRUPT_ENABLE 13 121 #define DMA_D_INTERRUPT_ENABLE 12 122 #define DMA_C_INTERRUPT_ENABLE 11 123 #define DMA_B_INTERRUPT_ENABLE 10 124 #define DMA_A_INTERRUPT_ENABLE 9 125 #define EEPROM_DONE_INTERRUPT_ENABLE 8 126 #define VBUS_INTERRUPT_ENABLE 7 127 #define CONTROL_STATUS_INTERRUPT_ENABLE 6 128 #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 129 #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 130 #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 131 #define RESUME_INTERRUPT_ENABLE 1 132 #define SOF_INTERRUPT_ENABLE 0 133 134 /* offset 0x0020 */ 135 u32 _unused1; 136 u32 usbirqenb1; 137 #define USB_INTERRUPT_ENABLE 31 138 #define POWER_STATE_CHANGE_INTERRUPT_ENABLE 27 139 #define PCI_ARBITER_TIMEOUT_INTERRUPT_ENABLE 26 140 #define PCI_PARITY_ERROR_INTERRUPT_ENABLE 25 141 #define PCI_INTA_INTERRUPT_ENABLE 24 142 #define PCI_PME_INTERRUPT_ENABLE 23 143 #define PCI_SERR_INTERRUPT_ENABLE 22 144 #define PCI_PERR_INTERRUPT_ENABLE 21 145 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT_ENABLE 20 146 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT_ENABLE 19 147 #define PCI_RETRY_ABORT_INTERRUPT_ENABLE 17 148 #define PCI_MASTER_CYCLE_DONE_INTERRUPT_ENABLE 16 149 #define GPIO_INTERRUPT_ENABLE 13 150 #define DMA_D_INTERRUPT_ENABLE 12 151 #define DMA_C_INTERRUPT_ENABLE 11 152 #define DMA_B_INTERRUPT_ENABLE 10 153 #define DMA_A_INTERRUPT_ENABLE 9 154 #define EEPROM_DONE_INTERRUPT_ENABLE 8 155 #define VBUS_INTERRUPT_ENABLE 7 156 #define CONTROL_STATUS_INTERRUPT_ENABLE 6 157 #define ROOT_PORT_RESET_INTERRUPT_ENABLE 4 158 #define SUSPEND_REQUEST_INTERRUPT_ENABLE 3 159 #define SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE 2 160 #define RESUME_INTERRUPT_ENABLE 1 161 #define SOF_INTERRUPT_ENABLE 0 162 u32 irqstat0; 163 #define INTA_ASSERTED 12 164 #define SETUP_PACKET_INTERRUPT 7 165 #define ENDPOINT_F_INTERRUPT 6 166 #define ENDPOINT_E_INTERRUPT 5 167 #define ENDPOINT_D_INTERRUPT 4 168 #define ENDPOINT_C_INTERRUPT 3 169 #define ENDPOINT_B_INTERRUPT 2 170 #define ENDPOINT_A_INTERRUPT 1 171 #define ENDPOINT_0_INTERRUPT 0 172 u32 irqstat1; 173 #define POWER_STATE_CHANGE_INTERRUPT 27 174 #define PCI_ARBITER_TIMEOUT_INTERRUPT 26 175 #define PCI_PARITY_ERROR_INTERRUPT 25 176 #define PCI_INTA_INTERRUPT 24 177 #define PCI_PME_INTERRUPT 23 178 #define PCI_SERR_INTERRUPT 22 179 #define PCI_PERR_INTERRUPT 21 180 #define PCI_MASTER_ABORT_RECEIVED_INTERRUPT 20 181 #define PCI_TARGET_ABORT_RECEIVED_INTERRUPT 19 182 #define PCI_RETRY_ABORT_INTERRUPT 17 183 #define PCI_MASTER_CYCLE_DONE_INTERRUPT 16 184 #define SOF_DOWN_INTERRUPT 14 185 #define GPIO_INTERRUPT 13 186 #define DMA_D_INTERRUPT 12 187 #define DMA_C_INTERRUPT 11 188 #define DMA_B_INTERRUPT 10 189 #define DMA_A_INTERRUPT 9 190 #define EEPROM_DONE_INTERRUPT 8 191 #define VBUS_INTERRUPT 7 192 #define CONTROL_STATUS_INTERRUPT 6 193 #define ROOT_PORT_RESET_INTERRUPT 4 194 #define SUSPEND_REQUEST_INTERRUPT 3 195 #define SUSPEND_REQUEST_CHANGE_INTERRUPT 2 196 #define RESUME_INTERRUPT 1 197 #define SOF_INTERRUPT 0 198 /* offset 0x0030 */ 199 u32 idxaddr; 200 u32 idxdata; 201 u32 fifoctl; 202 #define PCI_BASE2_RANGE 16 203 #define IGNORE_FIFO_AVAILABILITY 3 204 #define PCI_BASE2_SELECT 2 205 #define FIFO_CONFIGURATION_SELECT 0 206 u32 _unused2; 207 /* offset 0x0040 */ 208 u32 memaddr; 209 #define START 28 210 #define DIRECTION 27 211 #define FIFO_DIAGNOSTIC_SELECT 24 212 #define MEMORY_ADDRESS 0 213 u32 memdata0; 214 u32 memdata1; 215 u32 _unused3; 216 /* offset 0x0050 */ 217 u32 gpioctl; 218 #define GPIO3_LED_SELECT 12 219 #define GPIO3_INTERRUPT_ENABLE 11 220 #define GPIO2_INTERRUPT_ENABLE 10 221 #define GPIO1_INTERRUPT_ENABLE 9 222 #define GPIO0_INTERRUPT_ENABLE 8 223 #define GPIO3_OUTPUT_ENABLE 7 224 #define GPIO2_OUTPUT_ENABLE 6 225 #define GPIO1_OUTPUT_ENABLE 5 226 #define GPIO0_OUTPUT_ENABLE 4 227 #define GPIO3_DATA 3 228 #define GPIO2_DATA 2 229 #define GPIO1_DATA 1 230 #define GPIO0_DATA 0 231 u32 gpiostat; 232 #define GPIO3_INTERRUPT 3 233 #define GPIO2_INTERRUPT 2 234 #define GPIO1_INTERRUPT 1 235 #define GPIO0_INTERRUPT 0 236 } __attribute__ ((packed)); 237 238 /* usb control, BAR0 + 0x0080 */ 239 struct net2280_usb_regs { 240 /* offset 0x0080 */ 241 u32 stdrsp; 242 #define STALL_UNSUPPORTED_REQUESTS 31 243 #define SET_TEST_MODE 16 244 #define GET_OTHER_SPEED_CONFIGURATION 15 245 #define GET_DEVICE_QUALIFIER 14 246 #define SET_ADDRESS 13 247 #define ENDPOINT_SET_CLEAR_HALT 12 248 #define DEVICE_SET_CLEAR_DEVICE_REMOTE_WAKEUP 11 249 #define GET_STRING_DESCRIPTOR_2 10 250 #define GET_STRING_DESCRIPTOR_1 9 251 #define GET_STRING_DESCRIPTOR_0 8 252 #define GET_SET_INTERFACE 6 253 #define GET_SET_CONFIGURATION 5 254 #define GET_CONFIGURATION_DESCRIPTOR 4 255 #define GET_DEVICE_DESCRIPTOR 3 256 #define GET_ENDPOINT_STATUS 2 257 #define GET_INTERFACE_STATUS 1 258 #define GET_DEVICE_STATUS 0 259 u32 prodvendid; 260 #define PRODUCT_ID 16 261 #define VENDOR_ID 0 262 u32 relnum; 263 u32 usbctl; 264 #define SERIAL_NUMBER_INDEX 16 265 #define PRODUCT_ID_STRING_ENABLE 13 266 #define VENDOR_ID_STRING_ENABLE 12 267 #define USB_ROOT_PORT_WAKEUP_ENABLE 11 268 #define VBUS_PIN 10 269 #define TIMED_DISCONNECT 9 270 #define SUSPEND_IMMEDIATELY 7 271 #define SELF_POWERED_USB_DEVICE 6 272 #define REMOTE_WAKEUP_SUPPORT 5 273 #define PME_POLARITY 4 274 #define USB_DETECT_ENABLE 3 275 #define PME_WAKEUP_ENABLE 2 276 #define DEVICE_REMOTE_WAKEUP_ENABLE 1 277 #define SELF_POWERED_STATUS 0 278 /* offset 0x0090 */ 279 u32 usbstat; 280 #define HIGH_SPEED 7 281 #define FULL_SPEED 6 282 #define GENERATE_RESUME 5 283 #define GENERATE_DEVICE_REMOTE_WAKEUP 4 284 u32 xcvrdiag; 285 #define FORCE_HIGH_SPEED_MODE 31 286 #define FORCE_FULL_SPEED_MODE 30 287 #define USB_TEST_MODE 24 288 #define LINE_STATE 16 289 #define TRANSCEIVER_OPERATION_MODE 2 290 #define TRANSCEIVER_SELECT 1 291 #define TERMINATION_SELECT 0 292 u32 setup0123; 293 u32 setup4567; 294 /* offset 0x0090 */ 295 u32 _unused0; 296 u32 ouraddr; 297 #define FORCE_IMMEDIATE 7 298 #define OUR_USB_ADDRESS 0 299 u32 ourconfig; 300 } __attribute__ ((packed)); 301 302 /* pci control, BAR0 + 0x0100 */ 303 struct net2280_pci_regs { 304 /* offset 0x0100 */ 305 u32 pcimstctl; 306 #define PCI_ARBITER_PARK_SELECT 13 307 #define PCI_MULTI LEVEL_ARBITER 12 308 #define PCI_RETRY_ABORT_ENABLE 11 309 #define DMA_MEMORY_WRITE_AND_INVALIDATE_ENABLE 10 310 #define DMA_READ_MULTIPLE_ENABLE 9 311 #define DMA_READ_LINE_ENABLE 8 312 #define PCI_MASTER_COMMAND_SELECT 6 313 #define MEM_READ_OR_WRITE 0 314 #define IO_READ_OR_WRITE 1 315 #define CFG_READ_OR_WRITE 2 316 #define PCI_MASTER_START 5 317 #define PCI_MASTER_READ_WRITE 4 318 #define PCI_MASTER_WRITE 0 319 #define PCI_MASTER_READ 1 320 #define PCI_MASTER_BYTE_WRITE_ENABLES 0 321 u32 pcimstaddr; 322 u32 pcimstdata; 323 u32 pcimststat; 324 #define PCI_ARBITER_CLEAR 2 325 #define PCI_EXTERNAL_ARBITER 1 326 #define PCI_HOST_MODE 0 327 } __attribute__ ((packed)); 328 329 /* dma control, BAR0 + 0x0180 ... array of four structs like this, 330 * for channels 0..3. see also struct net2280_dma: descriptor 331 * that can be loaded into some of these registers. 332 */ 333 struct net2280_dma_regs { /* [11.7] */ 334 /* offset 0x0180, 0x01a0, 0x01c0, 0x01e0, */ 335 u32 dmactl; 336 #define DMA_SCATTER_GATHER_DONE_INTERRUPT_ENABLE 25 337 #define DMA_CLEAR_COUNT_ENABLE 21 338 #define DESCRIPTOR_POLLING_RATE 19 339 #define POLL_CONTINUOUS 0 340 #define POLL_1_USEC 1 341 #define POLL_100_USEC 2 342 #define POLL_1_MSEC 3 343 #define DMA_VALID_BIT_POLLING_ENABLE 18 344 #define DMA_VALID_BIT_ENABLE 17 345 #define DMA_SCATTER_GATHER_ENABLE 16 346 #define DMA_OUT_AUTO_START_ENABLE 4 347 #define DMA_PREEMPT_ENABLE 3 348 #define DMA_FIFO_VALIDATE 2 349 #define DMA_ENABLE 1 350 #define DMA_ADDRESS_HOLD 0 351 u32 dmastat; 352 #define DMA_ABORT_DONE_INTERRUPT 27 353 #define DMA_SCATTER_GATHER_DONE_INTERRUPT 25 354 #define DMA_TRANSACTION_DONE_INTERRUPT 24 355 #define DMA_ABORT 1 356 #define DMA_START 0 357 u32 _unused0 [2]; 358 /* offset 0x0190, 0x01b0, 0x01d0, 0x01f0, */ 359 u32 dmacount; 360 #define VALID_BIT 31 361 #define DMA_DIRECTION 30 362 #define DMA_DONE_INTERRUPT_ENABLE 29 363 #define END_OF_CHAIN 28 364 #define DMA_BYTE_COUNT_MASK ((1<<24)-1) 365 #define DMA_BYTE_COUNT 0 366 u32 dmaaddr; 367 u32 dmadesc; 368 u32 _unused1; 369 } __attribute__ ((packed)); 370 371 /* dedicated endpoint registers, BAR0 + 0x0200 */ 372 373 struct net2280_dep_regs { /* [11.8] */ 374 /* offset 0x0200, 0x0210, 0x220, 0x230, 0x240 */ 375 u32 dep_cfg; 376 /* offset 0x0204, 0x0214, 0x224, 0x234, 0x244 */ 377 u32 dep_rsp; 378 u32 _unused [2]; 379 } __attribute__ ((packed)); 380 381 /* configurable endpoint registers, BAR0 + 0x0300 ... array of seven structs 382 * like this, for ep0 then the configurable endpoints A..F 383 * ep0 reserved for control; E and F have only 64 bytes of fifo 384 */ 385 struct net2280_ep_regs { /* [11.9] */ 386 /* offset 0x0300, 0x0320, 0x0340, 0x0360, 0x0380, 0x03a0, 0x03c0 */ 387 u32 ep_cfg; 388 #define ENDPOINT_BYTE_COUNT 16 389 #define ENDPOINT_ENABLE 10 390 #define ENDPOINT_TYPE 8 391 #define ENDPOINT_DIRECTION 7 392 #define ENDPOINT_NUMBER 0 393 u32 ep_rsp; 394 #define SET_NAK_OUT_PACKETS 15 395 #define SET_EP_HIDE_STATUS_PHASE 14 396 #define SET_EP_FORCE_CRC_ERROR 13 397 #define SET_INTERRUPT_MODE 12 398 #define SET_CONTROL_STATUS_PHASE_HANDSHAKE 11 399 #define SET_NAK_OUT_PACKETS_MODE 10 400 #define SET_ENDPOINT_TOGGLE 9 401 #define SET_ENDPOINT_HALT 8 402 #define CLEAR_NAK_OUT_PACKETS 7 403 #define CLEAR_EP_HIDE_STATUS_PHASE 6 404 #define CLEAR_EP_FORCE_CRC_ERROR 5 405 #define CLEAR_INTERRUPT_MODE 4 406 #define CLEAR_CONTROL_STATUS_PHASE_HANDSHAKE 3 407 #define CLEAR_NAK_OUT_PACKETS_MODE 2 408 #define CLEAR_ENDPOINT_TOGGLE 1 409 #define CLEAR_ENDPOINT_HALT 0 410 u32 ep_irqenb; 411 #define SHORT_PACKET_OUT_DONE_INTERRUPT_ENABLE 6 412 #define SHORT_PACKET_TRANSFERRED_INTERRUPT_ENABLE 5 413 #define DATA_PACKET_RECEIVED_INTERRUPT_ENABLE 3 414 #define DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE 2 415 #define DATA_OUT_PING_TOKEN_INTERRUPT_ENABLE 1 416 #define DATA_IN_TOKEN_INTERRUPT_ENABLE 0 417 u32 ep_stat; 418 #define FIFO_VALID_COUNT 24 419 #define HIGH_BANDWIDTH_OUT_TRANSACTION_PID 22 420 #define TIMEOUT 21 421 #define USB_STALL_SENT 20 422 #define USB_IN_NAK_SENT 19 423 #define USB_IN_ACK_RCVD 18 424 #define USB_OUT_PING_NAK_SENT 17 425 #define USB_OUT_ACK_SENT 16 426 #define FIFO_OVERFLOW 13 427 #define FIFO_UNDERFLOW 12 428 #define FIFO_FULL 11 429 #define FIFO_EMPTY 10 430 #define FIFO_FLUSH 9 431 #define SHORT_PACKET_OUT_DONE_INTERRUPT 6 432 #define SHORT_PACKET_TRANSFERRED_INTERRUPT 5 433 #define NAK_OUT_PACKETS 4 434 #define DATA_PACKET_RECEIVED_INTERRUPT 3 435 #define DATA_PACKET_TRANSMITTED_INTERRUPT 2 436 #define DATA_OUT_PING_TOKEN_INTERRUPT 1 437 #define DATA_IN_TOKEN_INTERRUPT 0 438 /* offset 0x0310, 0x0330, 0x0350, 0x0370, 0x0390, 0x03b0, 0x03d0 */ 439 u32 ep_avail; 440 u32 ep_data; 441 u32 _unused0 [2]; 442 } __attribute__ ((packed)); 443 444 #endif /* __LINUX_USB_NET2280_H */ 445