1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * twl4030.h - header for TWL4030 PM and audio CODEC device 4 * 5 * Copyright (C) 2005-2006 Texas Instruments, Inc. 6 * 7 * Based on tlv320aic23.c: 8 * Copyright (c) by Kai Svahn <kai.svahn@nokia.com> 9 */ 10 11 #ifndef __TWL_H_ 12 #define __TWL_H_ 13 14 #include <linux/types.h> 15 #include <linux/input/matrix_keypad.h> 16 17 /* 18 * Using the twl4030 core we address registers using a pair 19 * { module id, relative register offset } 20 * which that core then maps to the relevant 21 * { i2c slave, absolute register address } 22 * 23 * The module IDs are meaningful only to the twl4030 core code, 24 * which uses them as array indices to look up the first register 25 * address each module uses within a given i2c slave. 26 */ 27 28 /* Module IDs for similar functionalities found in twl4030/twl6030 */ 29 enum twl_module_ids { 30 TWL_MODULE_USB, 31 TWL_MODULE_PIH, 32 TWL_MODULE_MAIN_CHARGE, 33 TWL_MODULE_PM_MASTER, 34 TWL_MODULE_PM_RECEIVER, 35 36 TWL_MODULE_RTC, 37 TWL_MODULE_PWM, 38 TWL_MODULE_LED, 39 TWL_MODULE_SECURED_REG, 40 41 TWL_MODULE_LAST, 42 }; 43 44 /* Modules only available in twl4030 series */ 45 enum twl4030_module_ids { 46 TWL4030_MODULE_AUDIO_VOICE = TWL_MODULE_LAST, 47 TWL4030_MODULE_GPIO, 48 TWL4030_MODULE_INTBR, 49 TWL4030_MODULE_TEST, 50 TWL4030_MODULE_KEYPAD, 51 52 TWL4030_MODULE_MADC, 53 TWL4030_MODULE_INTERRUPTS, 54 TWL4030_MODULE_PRECHARGE, 55 TWL4030_MODULE_BACKUP, 56 TWL4030_MODULE_INT, 57 58 TWL5031_MODULE_ACCESSORY, 59 TWL5031_MODULE_INTERRUPTS, 60 61 TWL4030_MODULE_LAST, 62 }; 63 64 /* Modules only available in twl6030 series */ 65 enum twl6030_module_ids { 66 TWL6030_MODULE_ID0 = TWL_MODULE_LAST, 67 TWL6030_MODULE_ID1, 68 TWL6030_MODULE_ID2, 69 TWL6030_MODULE_GPADC, 70 TWL6030_MODULE_GASGAUGE, 71 72 TWL6030_MODULE_LAST, 73 }; 74 75 /* Until the clients has been converted to use TWL_MODULE_LED */ 76 #define TWL4030_MODULE_LED TWL_MODULE_LED 77 78 #define GPIO_INTR_OFFSET 0 79 #define KEYPAD_INTR_OFFSET 1 80 #define BCI_INTR_OFFSET 2 81 #define MADC_INTR_OFFSET 3 82 #define USB_INTR_OFFSET 4 83 #define CHARGERFAULT_INTR_OFFSET 5 84 #define BCI_PRES_INTR_OFFSET 9 85 #define USB_PRES_INTR_OFFSET 10 86 #define RTC_INTR_OFFSET 11 87 88 /* 89 * Offset from TWL6030_IRQ_BASE / pdata->irq_base 90 */ 91 #define PWR_INTR_OFFSET 0 92 #define HOTDIE_INTR_OFFSET 12 93 #define SMPSLDO_INTR_OFFSET 13 94 #define BATDETECT_INTR_OFFSET 14 95 #define SIMDETECT_INTR_OFFSET 15 96 #define MMCDETECT_INTR_OFFSET 16 97 #define GASGAUGE_INTR_OFFSET 17 98 #define USBOTG_INTR_OFFSET 4 99 #define CHARGER_INTR_OFFSET 2 100 #define RSV_INTR_OFFSET 0 101 102 /* INT register offsets */ 103 #define REG_INT_STS_A 0x00 104 #define REG_INT_STS_B 0x01 105 #define REG_INT_STS_C 0x02 106 107 #define REG_INT_MSK_LINE_A 0x03 108 #define REG_INT_MSK_LINE_B 0x04 109 #define REG_INT_MSK_LINE_C 0x05 110 111 #define REG_INT_MSK_STS_A 0x06 112 #define REG_INT_MSK_STS_B 0x07 113 #define REG_INT_MSK_STS_C 0x08 114 115 /* MASK INT REG GROUP A */ 116 #define TWL6030_PWR_INT_MASK 0x07 117 #define TWL6030_RTC_INT_MASK 0x18 118 #define TWL6030_HOTDIE_INT_MASK 0x20 119 #define TWL6030_SMPSLDOA_INT_MASK 0xC0 120 121 /* MASK INT REG GROUP B */ 122 #define TWL6030_SMPSLDOB_INT_MASK 0x01 123 #define TWL6030_BATDETECT_INT_MASK 0x02 124 #define TWL6030_SIMDETECT_INT_MASK 0x04 125 #define TWL6030_MMCDETECT_INT_MASK 0x08 126 #define TWL6030_GPADC_INT_MASK 0x60 127 #define TWL6030_GASGAUGE_INT_MASK 0x80 128 129 /* MASK INT REG GROUP C */ 130 #define TWL6030_USBOTG_INT_MASK 0x0F 131 #define TWL6030_CHARGER_CTRL_INT_MASK 0x10 132 #define TWL6030_CHARGER_FAULT_INT_MASK 0x60 133 134 #define TWL6030_MMCCTRL 0xEE 135 #define VMMC_AUTO_OFF (0x1 << 3) 136 #define SW_FC (0x1 << 2) 137 #define STS_MMC 0x1 138 139 #define TWL6030_CFG_INPUT_PUPD3 0xF2 140 #define MMC_PU (0x1 << 3) 141 #define MMC_PD (0x1 << 2) 142 143 #define TWL_SIL_TYPE(rev) ((rev) & 0x00FFFFFF) 144 #define TWL_SIL_REV(rev) ((rev) >> 24) 145 #define TWL_SIL_5030 0x09002F 146 #define TWL5030_REV_1_0 0x00 147 #define TWL5030_REV_1_1 0x10 148 #define TWL5030_REV_1_2 0x30 149 150 #define TWL4030_CLASS_ID 0x4030 151 #define TWL6030_CLASS_ID 0x6030 152 unsigned int twl_rev(void); 153 #define GET_TWL_REV (twl_rev()) 154 #define TWL_CLASS_IS(class, id) \ 155 static inline int twl_class_is_ ##class(void) \ 156 { \ 157 return ((id) == (GET_TWL_REV)) ? 1 : 0; \ 158 } 159 160 TWL_CLASS_IS(4030, TWL4030_CLASS_ID) 161 TWL_CLASS_IS(6030, TWL6030_CLASS_ID) 162 163 /* Set the regcache bypass for the regmap associated with the nodule */ 164 int twl_set_regcache_bypass(u8 mod_no, bool enable); 165 166 /* 167 * Read and write several 8-bit registers at once. 168 */ 169 int twl_i2c_write(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); 170 int twl_i2c_read(u8 mod_no, u8 *value, u8 reg, unsigned num_bytes); 171 172 /* 173 * Read and write single 8-bit registers 174 */ 175 static inline int twl_i2c_write_u8(u8 mod_no, u8 val, u8 reg) { 176 return twl_i2c_write(mod_no, &val, reg, 1); 177 } 178 179 static inline int twl_i2c_read_u8(u8 mod_no, u8 *val, u8 reg) { 180 return twl_i2c_read(mod_no, val, reg, 1); 181 } 182 183 static inline int twl_i2c_write_u16(u8 mod_no, u16 val, u8 reg) { 184 __le16 value; 185 186 value = cpu_to_le16(val); 187 return twl_i2c_write(mod_no, (u8 *) &value, reg, 2); 188 } 189 190 static inline int twl_i2c_read_u16(u8 mod_no, u16 *val, u8 reg) { 191 int ret; 192 __le16 value; 193 194 ret = twl_i2c_read(mod_no, (u8 *) &value, reg, 2); 195 *val = le16_to_cpu(value); 196 return ret; 197 } 198 199 int twl_get_type(void); 200 int twl_get_version(void); 201 int twl_get_hfclk_rate(void); 202 203 int twl6030_interrupt_unmask(u8 bit_mask, u8 offset); 204 int twl6030_interrupt_mask(u8 bit_mask, u8 offset); 205 206 /* Card detect Configuration for MMC1 Controller on OMAP4 */ 207 #ifdef CONFIG_TWL4030_CORE 208 int twl6030_mmc_card_detect_config(void); 209 #else 210 static inline int twl6030_mmc_card_detect_config(void) 211 { 212 pr_debug("twl6030_mmc_card_detect_config not supported\n"); 213 return 0; 214 } 215 #endif 216 217 /* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */ 218 #ifdef CONFIG_TWL4030_CORE 219 int twl6030_mmc_card_detect(struct device *dev, int slot); 220 #else 221 static inline int twl6030_mmc_card_detect(struct device *dev, int slot) 222 { 223 pr_debug("Call back twl6030_mmc_card_detect not supported\n"); 224 return -EIO; 225 } 226 #endif 227 /*----------------------------------------------------------------------*/ 228 229 /* 230 * NOTE: at up to 1024 registers, this is a big chip. 231 * 232 * Avoid putting register declarations in this file, instead of into 233 * a driver-private file, unless some of the registers in a block 234 * need to be shared with other drivers. One example is blocks that 235 * have Secondary IRQ Handler (SIH) registers. 236 */ 237 238 #define TWL4030_SIH_CTRL_EXCLEN_MASK BIT(0) 239 #define TWL4030_SIH_CTRL_PENDDIS_MASK BIT(1) 240 #define TWL4030_SIH_CTRL_COR_MASK BIT(2) 241 242 /*----------------------------------------------------------------------*/ 243 244 /* 245 * GPIO Block Register offsets (use TWL4030_MODULE_GPIO) 246 */ 247 248 #define REG_GPIODATAIN1 0x0 249 #define REG_GPIODATAIN2 0x1 250 #define REG_GPIODATAIN3 0x2 251 #define REG_GPIODATADIR1 0x3 252 #define REG_GPIODATADIR2 0x4 253 #define REG_GPIODATADIR3 0x5 254 #define REG_GPIODATAOUT1 0x6 255 #define REG_GPIODATAOUT2 0x7 256 #define REG_GPIODATAOUT3 0x8 257 #define REG_CLEARGPIODATAOUT1 0x9 258 #define REG_CLEARGPIODATAOUT2 0xA 259 #define REG_CLEARGPIODATAOUT3 0xB 260 #define REG_SETGPIODATAOUT1 0xC 261 #define REG_SETGPIODATAOUT2 0xD 262 #define REG_SETGPIODATAOUT3 0xE 263 #define REG_GPIO_DEBEN1 0xF 264 #define REG_GPIO_DEBEN2 0x10 265 #define REG_GPIO_DEBEN3 0x11 266 #define REG_GPIO_CTRL 0x12 267 #define REG_GPIOPUPDCTR1 0x13 268 #define REG_GPIOPUPDCTR2 0x14 269 #define REG_GPIOPUPDCTR3 0x15 270 #define REG_GPIOPUPDCTR4 0x16 271 #define REG_GPIOPUPDCTR5 0x17 272 #define REG_GPIO_ISR1A 0x19 273 #define REG_GPIO_ISR2A 0x1A 274 #define REG_GPIO_ISR3A 0x1B 275 #define REG_GPIO_IMR1A 0x1C 276 #define REG_GPIO_IMR2A 0x1D 277 #define REG_GPIO_IMR3A 0x1E 278 #define REG_GPIO_ISR1B 0x1F 279 #define REG_GPIO_ISR2B 0x20 280 #define REG_GPIO_ISR3B 0x21 281 #define REG_GPIO_IMR1B 0x22 282 #define REG_GPIO_IMR2B 0x23 283 #define REG_GPIO_IMR3B 0x24 284 #define REG_GPIO_EDR1 0x28 285 #define REG_GPIO_EDR2 0x29 286 #define REG_GPIO_EDR3 0x2A 287 #define REG_GPIO_EDR4 0x2B 288 #define REG_GPIO_EDR5 0x2C 289 #define REG_GPIO_SIH_CTRL 0x2D 290 291 /* Up to 18 signals are available as GPIOs, when their 292 * pins are not assigned to another use (such as ULPI/USB). 293 */ 294 #define TWL4030_GPIO_MAX 18 295 296 /*----------------------------------------------------------------------*/ 297 298 /*Interface Bit Register (INTBR) offsets 299 *(Use TWL_4030_MODULE_INTBR) 300 */ 301 302 #define REG_IDCODE_7_0 0x00 303 #define REG_IDCODE_15_8 0x01 304 #define REG_IDCODE_16_23 0x02 305 #define REG_IDCODE_31_24 0x03 306 #define REG_GPPUPDCTR1 0x0F 307 #define REG_UNLOCK_TEST_REG 0x12 308 309 /*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */ 310 311 #define I2C_SCL_CTRL_PU BIT(0) 312 #define I2C_SDA_CTRL_PU BIT(2) 313 #define SR_I2C_SCL_CTRL_PU BIT(4) 314 #define SR_I2C_SDA_CTRL_PU BIT(6) 315 316 #define TWL_EEPROM_R_UNLOCK 0x49 317 318 /*----------------------------------------------------------------------*/ 319 320 /* 321 * Keypad register offsets (use TWL4030_MODULE_KEYPAD) 322 * ... SIH/interrupt only 323 */ 324 325 #define TWL4030_KEYPAD_KEYP_ISR1 0x11 326 #define TWL4030_KEYPAD_KEYP_IMR1 0x12 327 #define TWL4030_KEYPAD_KEYP_ISR2 0x13 328 #define TWL4030_KEYPAD_KEYP_IMR2 0x14 329 #define TWL4030_KEYPAD_KEYP_SIR 0x15 /* test register */ 330 #define TWL4030_KEYPAD_KEYP_EDR 0x16 331 #define TWL4030_KEYPAD_KEYP_SIH_CTRL 0x17 332 333 /*----------------------------------------------------------------------*/ 334 335 /* 336 * Multichannel ADC register offsets (use TWL4030_MODULE_MADC) 337 * ... SIH/interrupt only 338 */ 339 340 #define TWL4030_MADC_ISR1 0x61 341 #define TWL4030_MADC_IMR1 0x62 342 #define TWL4030_MADC_ISR2 0x63 343 #define TWL4030_MADC_IMR2 0x64 344 #define TWL4030_MADC_SIR 0x65 /* test register */ 345 #define TWL4030_MADC_EDR 0x66 346 #define TWL4030_MADC_SIH_CTRL 0x67 347 348 /*----------------------------------------------------------------------*/ 349 350 /* 351 * Battery charger register offsets (use TWL4030_MODULE_INTERRUPTS) 352 */ 353 354 #define TWL4030_INTERRUPTS_BCIISR1A 0x0 355 #define TWL4030_INTERRUPTS_BCIISR2A 0x1 356 #define TWL4030_INTERRUPTS_BCIIMR1A 0x2 357 #define TWL4030_INTERRUPTS_BCIIMR2A 0x3 358 #define TWL4030_INTERRUPTS_BCIISR1B 0x4 359 #define TWL4030_INTERRUPTS_BCIISR2B 0x5 360 #define TWL4030_INTERRUPTS_BCIIMR1B 0x6 361 #define TWL4030_INTERRUPTS_BCIIMR2B 0x7 362 #define TWL4030_INTERRUPTS_BCISIR1 0x8 /* test register */ 363 #define TWL4030_INTERRUPTS_BCISIR2 0x9 /* test register */ 364 #define TWL4030_INTERRUPTS_BCIEDR1 0xa 365 #define TWL4030_INTERRUPTS_BCIEDR2 0xb 366 #define TWL4030_INTERRUPTS_BCIEDR3 0xc 367 #define TWL4030_INTERRUPTS_BCISIHCTRL 0xd 368 369 /*----------------------------------------------------------------------*/ 370 371 /* 372 * Power Interrupt block register offsets (use TWL4030_MODULE_INT) 373 */ 374 375 #define TWL4030_INT_PWR_ISR1 0x0 376 #define TWL4030_INT_PWR_IMR1 0x1 377 #define TWL4030_INT_PWR_ISR2 0x2 378 #define TWL4030_INT_PWR_IMR2 0x3 379 #define TWL4030_INT_PWR_SIR 0x4 /* test register */ 380 #define TWL4030_INT_PWR_EDR1 0x5 381 #define TWL4030_INT_PWR_EDR2 0x6 382 #define TWL4030_INT_PWR_SIH_CTRL 0x7 383 384 /*----------------------------------------------------------------------*/ 385 386 /* 387 * Accessory Interrupts 388 */ 389 #define TWL5031_ACIIMR_LSB 0x05 390 #define TWL5031_ACIIMR_MSB 0x06 391 #define TWL5031_ACIIDR_LSB 0x07 392 #define TWL5031_ACIIDR_MSB 0x08 393 #define TWL5031_ACCISR1 0x0F 394 #define TWL5031_ACCIMR1 0x10 395 #define TWL5031_ACCISR2 0x11 396 #define TWL5031_ACCIMR2 0x12 397 #define TWL5031_ACCSIR 0x13 398 #define TWL5031_ACCEDR1 0x14 399 #define TWL5031_ACCSIHCTRL 0x15 400 401 /*----------------------------------------------------------------------*/ 402 403 /* 404 * Battery Charger Controller 405 */ 406 407 #define TWL5031_INTERRUPTS_BCIISR1 0x0 408 #define TWL5031_INTERRUPTS_BCIIMR1 0x1 409 #define TWL5031_INTERRUPTS_BCIISR2 0x2 410 #define TWL5031_INTERRUPTS_BCIIMR2 0x3 411 #define TWL5031_INTERRUPTS_BCISIR 0x4 412 #define TWL5031_INTERRUPTS_BCIEDR1 0x5 413 #define TWL5031_INTERRUPTS_BCIEDR2 0x6 414 #define TWL5031_INTERRUPTS_BCISIHCTRL 0x7 415 416 /*----------------------------------------------------------------------*/ 417 418 /* 419 * PM Master module register offsets (use TWL4030_MODULE_PM_MASTER) 420 */ 421 422 #define TWL4030_PM_MASTER_CFG_P1_TRANSITION 0x00 423 #define TWL4030_PM_MASTER_CFG_P2_TRANSITION 0x01 424 #define TWL4030_PM_MASTER_CFG_P3_TRANSITION 0x02 425 #define TWL4030_PM_MASTER_CFG_P123_TRANSITION 0x03 426 #define TWL4030_PM_MASTER_STS_BOOT 0x04 427 #define TWL4030_PM_MASTER_CFG_BOOT 0x05 428 #define TWL4030_PM_MASTER_SHUNDAN 0x06 429 #define TWL4030_PM_MASTER_BOOT_BCI 0x07 430 #define TWL4030_PM_MASTER_CFG_PWRANA1 0x08 431 #define TWL4030_PM_MASTER_CFG_PWRANA2 0x09 432 #define TWL4030_PM_MASTER_BACKUP_MISC_STS 0x0b 433 #define TWL4030_PM_MASTER_BACKUP_MISC_CFG 0x0c 434 #define TWL4030_PM_MASTER_BACKUP_MISC_TST 0x0d 435 #define TWL4030_PM_MASTER_PROTECT_KEY 0x0e 436 #define TWL4030_PM_MASTER_STS_HW_CONDITIONS 0x0f 437 #define TWL4030_PM_MASTER_P1_SW_EVENTS 0x10 438 #define TWL4030_PM_MASTER_P2_SW_EVENTS 0x11 439 #define TWL4030_PM_MASTER_P3_SW_EVENTS 0x12 440 #define TWL4030_PM_MASTER_STS_P123_STATE 0x13 441 #define TWL4030_PM_MASTER_PB_CFG 0x14 442 #define TWL4030_PM_MASTER_PB_WORD_MSB 0x15 443 #define TWL4030_PM_MASTER_PB_WORD_LSB 0x16 444 #define TWL4030_PM_MASTER_SEQ_ADD_W2P 0x1c 445 #define TWL4030_PM_MASTER_SEQ_ADD_P2A 0x1d 446 #define TWL4030_PM_MASTER_SEQ_ADD_A2W 0x1e 447 #define TWL4030_PM_MASTER_SEQ_ADD_A2S 0x1f 448 #define TWL4030_PM_MASTER_SEQ_ADD_S2A12 0x20 449 #define TWL4030_PM_MASTER_SEQ_ADD_S2A3 0x21 450 #define TWL4030_PM_MASTER_SEQ_ADD_WARM 0x22 451 #define TWL4030_PM_MASTER_MEMORY_ADDRESS 0x23 452 #define TWL4030_PM_MASTER_MEMORY_DATA 0x24 453 454 #define TWL4030_PM_MASTER_KEY_CFG1 0xc0 455 #define TWL4030_PM_MASTER_KEY_CFG2 0x0c 456 457 #define TWL4030_PM_MASTER_KEY_TST1 0xe0 458 #define TWL4030_PM_MASTER_KEY_TST2 0x0e 459 460 #define TWL4030_PM_MASTER_GLOBAL_TST 0xb6 461 462 /*----------------------------------------------------------------------*/ 463 464 /* Power bus message definitions */ 465 466 /* The TWL4030/5030 splits its power-management resources (the various 467 * regulators, clock and reset lines) into 3 processor groups - P1, P2 and 468 * P3. These groups can then be configured to transition between sleep, wait-on 469 * and active states by sending messages to the power bus. See Section 5.4.2 470 * Power Resources of TWL4030 TRM 471 */ 472 473 /* Processor groups */ 474 #define DEV_GRP_NULL 0x0 475 #define DEV_GRP_P1 0x1 /* P1: all OMAP devices */ 476 #define DEV_GRP_P2 0x2 /* P2: all Modem devices */ 477 #define DEV_GRP_P3 0x4 /* P3: all peripheral devices */ 478 479 /* Resource groups */ 480 #define RES_GRP_RES 0x0 /* Reserved */ 481 #define RES_GRP_PP 0x1 /* Power providers */ 482 #define RES_GRP_RC 0x2 /* Reset and control */ 483 #define RES_GRP_PP_RC 0x3 484 #define RES_GRP_PR 0x4 /* Power references */ 485 #define RES_GRP_PP_PR 0x5 486 #define RES_GRP_RC_PR 0x6 487 #define RES_GRP_ALL 0x7 /* All resource groups */ 488 489 #define RES_TYPE2_R0 0x0 490 #define RES_TYPE2_R1 0x1 491 #define RES_TYPE2_R2 0x2 492 493 #define RES_TYPE_R0 0x0 494 #define RES_TYPE_ALL 0x7 495 496 /* Resource states */ 497 #define RES_STATE_WRST 0xF 498 #define RES_STATE_ACTIVE 0xE 499 #define RES_STATE_SLEEP 0x8 500 #define RES_STATE_OFF 0x0 501 502 /* Power resources */ 503 504 /* Power providers */ 505 #define RES_VAUX1 1 506 #define RES_VAUX2 2 507 #define RES_VAUX3 3 508 #define RES_VAUX4 4 509 #define RES_VMMC1 5 510 #define RES_VMMC2 6 511 #define RES_VPLL1 7 512 #define RES_VPLL2 8 513 #define RES_VSIM 9 514 #define RES_VDAC 10 515 #define RES_VINTANA1 11 516 #define RES_VINTANA2 12 517 #define RES_VINTDIG 13 518 #define RES_VIO 14 519 #define RES_VDD1 15 520 #define RES_VDD2 16 521 #define RES_VUSB_1V5 17 522 #define RES_VUSB_1V8 18 523 #define RES_VUSB_3V1 19 524 #define RES_VUSBCP 20 525 #define RES_REGEN 21 526 /* Reset and control */ 527 #define RES_NRES_PWRON 22 528 #define RES_CLKEN 23 529 #define RES_SYSEN 24 530 #define RES_HFCLKOUT 25 531 #define RES_32KCLKOUT 26 532 #define RES_RESET 27 533 /* Power Reference */ 534 #define RES_MAIN_REF 28 535 536 #define TOTAL_RESOURCES 28 537 /* 538 * Power Bus Message Format ... these can be sent individually by Linux, 539 * but are usually part of downloaded scripts that are run when various 540 * power events are triggered. 541 * 542 * Broadcast Message (16 Bits): 543 * DEV_GRP[15:13] MT[12] RES_GRP[11:9] RES_TYPE2[8:7] RES_TYPE[6:4] 544 * RES_STATE[3:0] 545 * 546 * Singular Message (16 Bits): 547 * DEV_GRP[15:13] MT[12] RES_ID[11:4] RES_STATE[3:0] 548 */ 549 550 #define MSG_BROADCAST(devgrp, grp, type, type2, state) \ 551 ( (devgrp) << 13 | 1 << 12 | (grp) << 9 | (type2) << 7 \ 552 | (type) << 4 | (state)) 553 554 #define MSG_SINGULAR(devgrp, id, state) \ 555 ((devgrp) << 13 | 0 << 12 | (id) << 4 | (state)) 556 557 #define MSG_BROADCAST_ALL(devgrp, state) \ 558 ((devgrp) << 5 | (state)) 559 560 #define MSG_BROADCAST_REF MSG_BROADCAST_ALL 561 #define MSG_BROADCAST_PROV MSG_BROADCAST_ALL 562 #define MSG_BROADCAST__CLK_RST MSG_BROADCAST_ALL 563 /*----------------------------------------------------------------------*/ 564 565 struct twl4030_clock_init_data { 566 bool ck32k_lowpwr_enable; 567 }; 568 569 struct twl4030_bci_platform_data { 570 int *battery_tmp_tbl; 571 unsigned int tblsize; 572 int bb_uvolt; /* voltage to charge backup battery */ 573 int bb_uamp; /* current for backup battery charging */ 574 }; 575 576 /* TWL4030_GPIO_MAX (18) GPIOs, with interrupts */ 577 struct twl4030_gpio_platform_data { 578 /* package the two LED signals as output-only GPIOs? */ 579 bool use_leds; 580 581 /* gpio-n should control VMMC(n+1) if BIT(n) in mmc_cd is set */ 582 u8 mmc_cd; 583 584 /* if BIT(N) is set, or VMMC(n+1) is linked, debounce GPIO-N */ 585 u32 debounce; 586 587 /* For gpio-N, bit (1 << N) in "pullups" is set if that pullup 588 * should be enabled. Else, if that bit is set in "pulldowns", 589 * that pulldown is enabled. Don't waste power by letting any 590 * digital inputs float... 591 */ 592 u32 pullups; 593 u32 pulldowns; 594 595 int (*setup)(struct device *dev, 596 unsigned gpio, unsigned ngpio); 597 int (*teardown)(struct device *dev, 598 unsigned gpio, unsigned ngpio); 599 }; 600 601 struct twl4030_madc_platform_data { 602 int irq_line; 603 }; 604 605 /* Boards have unique mappings of {row, col} --> keycode. 606 * Column and row are 8 bits each, but range only from 0..7. 607 * a PERSISTENT_KEY is "always on" and never reported. 608 */ 609 #define PERSISTENT_KEY(r, c) KEY((r), (c), KEY_RESERVED) 610 611 struct twl4030_keypad_data { 612 const struct matrix_keymap_data *keymap_data; 613 unsigned rows; 614 unsigned cols; 615 bool rep; 616 }; 617 618 enum twl4030_usb_mode { 619 T2_USB_MODE_ULPI = 1, 620 T2_USB_MODE_CEA2011_3PIN = 2, 621 }; 622 623 struct twl4030_usb_data { 624 enum twl4030_usb_mode usb_mode; 625 unsigned long features; 626 627 int (*phy_init)(struct device *dev); 628 int (*phy_exit)(struct device *dev); 629 /* Power on/off the PHY */ 630 int (*phy_power)(struct device *dev, int iD, int on); 631 /* enable/disable phy clocks */ 632 int (*phy_set_clock)(struct device *dev, int on); 633 /* suspend/resume of phy */ 634 int (*phy_suspend)(struct device *dev, int suspend); 635 }; 636 637 struct twl4030_ins { 638 u16 pmb_message; 639 u8 delay; 640 }; 641 642 struct twl4030_script { 643 struct twl4030_ins *script; 644 unsigned size; 645 u8 flags; 646 #define TWL4030_WRST_SCRIPT (1<<0) 647 #define TWL4030_WAKEUP12_SCRIPT (1<<1) 648 #define TWL4030_WAKEUP3_SCRIPT (1<<2) 649 #define TWL4030_SLEEP_SCRIPT (1<<3) 650 }; 651 652 struct twl4030_resconfig { 653 u8 resource; 654 u8 devgroup; /* Processor group that Power resource belongs to */ 655 u8 type; /* Power resource addressed, 6 / broadcast message */ 656 u8 type2; /* Power resource addressed, 3 / broadcast message */ 657 u8 remap_off; /* off state remapping */ 658 u8 remap_sleep; /* sleep state remapping */ 659 }; 660 661 struct twl4030_power_data { 662 struct twl4030_script **scripts; 663 unsigned num; 664 struct twl4030_resconfig *resource_config; 665 struct twl4030_resconfig *board_config; 666 #define TWL4030_RESCONFIG_UNDEF ((u8)-1) 667 bool use_poweroff; /* Board is wired for TWL poweroff */ 668 bool ac_charger_quirk; /* Disable AC charger on board */ 669 }; 670 671 extern int twl4030_remove_script(u8 flags); 672 extern void twl4030_power_off(void); 673 674 struct twl4030_codec_data { 675 unsigned int digimic_delay; /* in ms */ 676 unsigned int ramp_delay_value; 677 unsigned int offset_cncl_path; 678 unsigned int hs_extmute:1; 679 int hs_extmute_gpio; 680 }; 681 682 struct twl4030_vibra_data { 683 unsigned int coexist; 684 }; 685 686 struct twl4030_audio_data { 687 unsigned int audio_mclk; 688 struct twl4030_codec_data *codec; 689 struct twl4030_vibra_data *vibra; 690 691 /* twl6040 */ 692 int audpwron_gpio; /* audio power-on gpio */ 693 int naudint_irq; /* audio interrupt */ 694 unsigned int irq_base; 695 }; 696 697 struct twl4030_platform_data { 698 struct twl4030_clock_init_data *clock; 699 struct twl4030_bci_platform_data *bci; 700 struct twl4030_gpio_platform_data *gpio; 701 struct twl4030_madc_platform_data *madc; 702 struct twl4030_keypad_data *keypad; 703 struct twl4030_usb_data *usb; 704 struct twl4030_power_data *power; 705 struct twl4030_audio_data *audio; 706 707 /* Common LDO regulators for TWL4030/TWL6030 */ 708 struct regulator_init_data *vdac; 709 struct regulator_init_data *vaux1; 710 struct regulator_init_data *vaux2; 711 struct regulator_init_data *vaux3; 712 struct regulator_init_data *vdd1; 713 struct regulator_init_data *vdd2; 714 struct regulator_init_data *vdd3; 715 /* TWL4030 LDO regulators */ 716 struct regulator_init_data *vpll1; 717 struct regulator_init_data *vpll2; 718 struct regulator_init_data *vmmc1; 719 struct regulator_init_data *vmmc2; 720 struct regulator_init_data *vsim; 721 struct regulator_init_data *vaux4; 722 struct regulator_init_data *vio; 723 struct regulator_init_data *vintana1; 724 struct regulator_init_data *vintana2; 725 struct regulator_init_data *vintdig; 726 /* TWL6030 LDO regulators */ 727 struct regulator_init_data *vmmc; 728 struct regulator_init_data *vpp; 729 struct regulator_init_data *vusim; 730 struct regulator_init_data *vana; 731 struct regulator_init_data *vcxio; 732 struct regulator_init_data *vusb; 733 struct regulator_init_data *clk32kg; 734 struct regulator_init_data *v1v8; 735 struct regulator_init_data *v2v1; 736 /* TWL6032 LDO regulators */ 737 struct regulator_init_data *ldo1; 738 struct regulator_init_data *ldo2; 739 struct regulator_init_data *ldo3; 740 struct regulator_init_data *ldo4; 741 struct regulator_init_data *ldo5; 742 struct regulator_init_data *ldo6; 743 struct regulator_init_data *ldo7; 744 struct regulator_init_data *ldoln; 745 struct regulator_init_data *ldousb; 746 /* TWL6032 DCDC regulators */ 747 struct regulator_init_data *smps3; 748 struct regulator_init_data *smps4; 749 struct regulator_init_data *vio6025; 750 }; 751 752 struct twl_regulator_driver_data { 753 int (*set_voltage)(void *data, int target_uV); 754 int (*get_voltage)(void *data); 755 void *data; 756 unsigned long features; 757 }; 758 /* chip-specific feature flags, for twl_regulator_driver_data.features */ 759 #define TWL4030_VAUX2 BIT(0) /* pre-5030 voltage ranges */ 760 #define TPS_SUBSET BIT(1) /* tps659[23]0 have fewer LDOs */ 761 #define TWL5031 BIT(2) /* twl5031 has different registers */ 762 #define TWL6030_CLASS BIT(3) /* TWL6030 class */ 763 #define TWL6032_SUBCLASS BIT(4) /* TWL6032 has changed registers */ 764 #define TWL4030_ALLOW_UNSUPPORTED BIT(5) /* Some voltages are possible 765 * but not officially supported. 766 * This flag is necessary to 767 * enable them. 768 */ 769 770 /*----------------------------------------------------------------------*/ 771 772 int twl4030_sih_setup(struct device *dev, int module, int irq_base); 773 774 /* Offsets to Power Registers */ 775 #define TWL4030_VDAC_DEV_GRP 0x3B 776 #define TWL4030_VDAC_DEDICATED 0x3E 777 #define TWL4030_VAUX1_DEV_GRP 0x17 778 #define TWL4030_VAUX1_DEDICATED 0x1A 779 #define TWL4030_VAUX2_DEV_GRP 0x1B 780 #define TWL4030_VAUX2_DEDICATED 0x1E 781 #define TWL4030_VAUX3_DEV_GRP 0x1F 782 #define TWL4030_VAUX3_DEDICATED 0x22 783 784 /*----------------------------------------------------------------------*/ 785 786 /* Linux-specific regulator identifiers ... for now, we only support 787 * the LDOs, and leave the three buck converters alone. VDD1 and VDD2 788 * need to tie into hardware based voltage scaling (cpufreq etc), while 789 * VIO is generally fixed. 790 */ 791 792 /* TWL4030 SMPS/LDO's */ 793 /* EXTERNAL dc-to-dc buck converters */ 794 #define TWL4030_REG_VDD1 0 795 #define TWL4030_REG_VDD2 1 796 #define TWL4030_REG_VIO 2 797 798 /* EXTERNAL LDOs */ 799 #define TWL4030_REG_VDAC 3 800 #define TWL4030_REG_VPLL1 4 801 #define TWL4030_REG_VPLL2 5 /* not on all chips */ 802 #define TWL4030_REG_VMMC1 6 803 #define TWL4030_REG_VMMC2 7 /* not on all chips */ 804 #define TWL4030_REG_VSIM 8 /* not on all chips */ 805 #define TWL4030_REG_VAUX1 9 /* not on all chips */ 806 #define TWL4030_REG_VAUX2_4030 10 /* (twl4030-specific) */ 807 #define TWL4030_REG_VAUX2 11 /* (twl5030 and newer) */ 808 #define TWL4030_REG_VAUX3 12 /* not on all chips */ 809 #define TWL4030_REG_VAUX4 13 /* not on all chips */ 810 811 /* INTERNAL LDOs */ 812 #define TWL4030_REG_VINTANA1 14 813 #define TWL4030_REG_VINTANA2 15 814 #define TWL4030_REG_VINTDIG 16 815 #define TWL4030_REG_VUSB1V5 17 816 #define TWL4030_REG_VUSB1V8 18 817 #define TWL4030_REG_VUSB3V1 19 818 819 /* TWL6030 SMPS/LDO's */ 820 /* EXTERNAL dc-to-dc buck convertor controllable via SR */ 821 #define TWL6030_REG_VDD1 30 822 #define TWL6030_REG_VDD2 31 823 #define TWL6030_REG_VDD3 32 824 825 /* Non SR compliant dc-to-dc buck convertors */ 826 #define TWL6030_REG_VMEM 33 827 #define TWL6030_REG_V2V1 34 828 #define TWL6030_REG_V1V29 35 829 #define TWL6030_REG_V1V8 36 830 831 /* EXTERNAL LDOs */ 832 #define TWL6030_REG_VAUX1_6030 37 833 #define TWL6030_REG_VAUX2_6030 38 834 #define TWL6030_REG_VAUX3_6030 39 835 #define TWL6030_REG_VMMC 40 836 #define TWL6030_REG_VPP 41 837 #define TWL6030_REG_VUSIM 42 838 #define TWL6030_REG_VANA 43 839 #define TWL6030_REG_VCXIO 44 840 #define TWL6030_REG_VDAC 45 841 #define TWL6030_REG_VUSB 46 842 843 /* INTERNAL LDOs */ 844 #define TWL6030_REG_VRTC 47 845 #define TWL6030_REG_CLK32KG 48 846 847 /* LDOs on 6025 have different names */ 848 #define TWL6032_REG_LDO2 49 849 #define TWL6032_REG_LDO4 50 850 #define TWL6032_REG_LDO3 51 851 #define TWL6032_REG_LDO5 52 852 #define TWL6032_REG_LDO1 53 853 #define TWL6032_REG_LDO7 54 854 #define TWL6032_REG_LDO6 55 855 #define TWL6032_REG_LDOLN 56 856 #define TWL6032_REG_LDOUSB 57 857 858 /* 6025 DCDC supplies */ 859 #define TWL6032_REG_SMPS3 58 860 #define TWL6032_REG_SMPS4 59 861 #define TWL6032_REG_VIO 60 862 863 864 #endif /* End of __TWL4030_H */ 865