1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * include/linux/input/adxl34x.h 4 * 5 * Digital Accelerometer characteristics are highly application specific 6 * and may vary between boards and models. The platform_data for the 7 * device's "struct device" holds this information. 8 * 9 * Copyright 2009 Analog Devices Inc. 10 */ 11 12 #ifndef __LINUX_INPUT_ADXL34X_H__ 13 #define __LINUX_INPUT_ADXL34X_H__ 14 15 #include <linux/input.h> 16 17 struct adxl34x_platform_data { 18 19 /* 20 * X,Y,Z Axis Offset: 21 * offer user offset adjustments in twoscompliment 22 * form with a scale factor of 15.6 mg/LSB (i.e. 0x7F = +2 g) 23 */ 24 25 s8 x_axis_offset; 26 s8 y_axis_offset; 27 s8 z_axis_offset; 28 29 /* 30 * TAP_X/Y/Z Enable: Setting TAP_X, Y, or Z Enable enables X, 31 * Y, or Z participation in Tap detection. A '0' excludes the 32 * selected axis from participation in Tap detection. 33 * Setting the SUPPRESS bit suppresses Double Tap detection if 34 * acceleration greater than tap_threshold is present during the 35 * tap_latency period, i.e. after the first tap but before the 36 * opening of the second tap window. 37 */ 38 39 #define ADXL_SUPPRESS (1 << 3) 40 #define ADXL_TAP_X_EN (1 << 2) 41 #define ADXL_TAP_Y_EN (1 << 1) 42 #define ADXL_TAP_Z_EN (1 << 0) 43 44 u8 tap_axis_control; 45 46 /* 47 * tap_threshold: 48 * holds the threshold value for tap detection/interrupts. 49 * The data format is unsigned. The scale factor is 62.5 mg/LSB 50 * (i.e. 0xFF = +16 g). A zero value may result in undesirable 51 * behavior if Tap/Double Tap is enabled. 52 */ 53 54 u8 tap_threshold; 55 56 /* 57 * tap_duration: 58 * is an unsigned time value representing the maximum 59 * time that an event must be above the tap_threshold threshold 60 * to qualify as a tap event. The scale factor is 625 us/LSB. A zero 61 * value will prevent Tap/Double Tap functions from working. 62 */ 63 64 u8 tap_duration; 65 66 /* 67 * tap_latency: 68 * is an unsigned time value representing the wait time 69 * from the detection of a tap event to the opening of the time 70 * window tap_window for a possible second tap event. The scale 71 * factor is 1.25 ms/LSB. A zero value will disable the Double Tap 72 * function. 73 */ 74 75 u8 tap_latency; 76 77 /* 78 * tap_window: 79 * is an unsigned time value representing the amount 80 * of time after the expiration of tap_latency during which a second 81 * tap can begin. The scale factor is 1.25 ms/LSB. A zero value will 82 * disable the Double Tap function. 83 */ 84 85 u8 tap_window; 86 87 /* 88 * act_axis_control: 89 * X/Y/Z Enable: A '1' enables X, Y, or Z participation in activity 90 * or inactivity detection. A '0' excludes the selected axis from 91 * participation. If all of the axes are excluded, the function is 92 * disabled. 93 * AC/DC: A '0' = DC coupled operation and a '1' = AC coupled 94 * operation. In DC coupled operation, the current acceleration is 95 * compared with activity_threshold and inactivity_threshold directly 96 * to determine whether activity or inactivity is detected. In AC 97 * coupled operation for activity detection, the acceleration value 98 * at the start of activity detection is taken as a reference value. 99 * New samples of acceleration are then compared to this 100 * reference value and if the magnitude of the difference exceeds 101 * activity_threshold the device will trigger an activity interrupt. In 102 * AC coupled operation for inactivity detection, a reference value 103 * is used again for comparison and is updated whenever the 104 * device exceeds the inactivity threshold. Once the reference 105 * value is selected, the device compares the magnitude of the 106 * difference between the reference value and the current 107 * acceleration with inactivity_threshold. If the difference is below 108 * inactivity_threshold for a total of inactivity_time, the device is 109 * considered inactive and the inactivity interrupt is triggered. 110 */ 111 112 #define ADXL_ACT_ACDC (1 << 7) 113 #define ADXL_ACT_X_EN (1 << 6) 114 #define ADXL_ACT_Y_EN (1 << 5) 115 #define ADXL_ACT_Z_EN (1 << 4) 116 #define ADXL_INACT_ACDC (1 << 3) 117 #define ADXL_INACT_X_EN (1 << 2) 118 #define ADXL_INACT_Y_EN (1 << 1) 119 #define ADXL_INACT_Z_EN (1 << 0) 120 121 u8 act_axis_control; 122 123 /* 124 * activity_threshold: 125 * holds the threshold value for activity detection. 126 * The data format is unsigned. The scale factor is 127 * 62.5 mg/LSB. A zero value may result in undesirable behavior if 128 * Activity interrupt is enabled. 129 */ 130 131 u8 activity_threshold; 132 133 /* 134 * inactivity_threshold: 135 * holds the threshold value for inactivity 136 * detection. The data format is unsigned. The scale 137 * factor is 62.5 mg/LSB. A zero value may result in undesirable 138 * behavior if Inactivity interrupt is enabled. 139 */ 140 141 u8 inactivity_threshold; 142 143 /* 144 * inactivity_time: 145 * is an unsigned time value representing the 146 * amount of time that acceleration must be below the value in 147 * inactivity_threshold for inactivity to be declared. The scale factor 148 * is 1 second/LSB. Unlike the other interrupt functions, which 149 * operate on unfiltered data, the inactivity function operates on the 150 * filtered output data. At least one output sample must be 151 * generated for the inactivity interrupt to be triggered. This will 152 * result in the function appearing un-responsive if the 153 * inactivity_time register is set with a value less than the time 154 * constant of the Output Data Rate. A zero value will result in an 155 * interrupt when the output data is below inactivity_threshold. 156 */ 157 158 u8 inactivity_time; 159 160 /* 161 * free_fall_threshold: 162 * holds the threshold value for Free-Fall detection. 163 * The data format is unsigned. The root-sum-square(RSS) value 164 * of all axes is calculated and compared to the value in 165 * free_fall_threshold to determine if a free fall event may be 166 * occurring. The scale factor is 62.5 mg/LSB. A zero value may 167 * result in undesirable behavior if Free-Fall interrupt is 168 * enabled. Values between 300 and 600 mg (0x05 to 0x09) are 169 * recommended. 170 */ 171 172 u8 free_fall_threshold; 173 174 /* 175 * free_fall_time: 176 * is an unsigned time value representing the minimum 177 * time that the RSS value of all axes must be less than 178 * free_fall_threshold to generate a Free-Fall interrupt. The 179 * scale factor is 5 ms/LSB. A zero value may result in 180 * undesirable behavior if Free-Fall interrupt is enabled. 181 * Values between 100 to 350 ms (0x14 to 0x46) are recommended. 182 */ 183 184 u8 free_fall_time; 185 186 /* 187 * data_rate: 188 * Selects device bandwidth and output data rate. 189 * RATE = 3200 Hz / (2^(15 - x)). Default value is 0x0A, or 100 Hz 190 * Output Data Rate. An Output Data Rate should be selected that 191 * is appropriate for the communication protocol and frequency 192 * selected. Selecting too high of an Output Data Rate with a low 193 * communication speed will result in samples being discarded. 194 */ 195 196 u8 data_rate; 197 198 /* 199 * data_range: 200 * FULL_RES: When this bit is set with the device is 201 * in Full-Resolution Mode, where the output resolution increases 202 * with RANGE to maintain a 4 mg/LSB scale factor. When this 203 * bit is cleared the device is in 10-bit Mode and RANGE determine the 204 * maximum g-Range and scale factor. 205 */ 206 207 #define ADXL_FULL_RES (1 << 3) 208 #define ADXL_RANGE_PM_2g 0 209 #define ADXL_RANGE_PM_4g 1 210 #define ADXL_RANGE_PM_8g 2 211 #define ADXL_RANGE_PM_16g 3 212 213 u8 data_range; 214 215 /* 216 * low_power_mode: 217 * A '0' = Normal operation and a '1' = Reduced 218 * power operation with somewhat higher noise. 219 */ 220 221 u8 low_power_mode; 222 223 /* 224 * power_mode: 225 * LINK: A '1' with both the activity and inactivity functions 226 * enabled will delay the start of the activity function until 227 * inactivity is detected. Once activity is detected, inactivity 228 * detection will begin and prevent the detection of activity. This 229 * bit serially links the activity and inactivity functions. When '0' 230 * the inactivity and activity functions are concurrent. Additional 231 * information can be found in the ADXL34x datasheet's Application 232 * section under Link Mode. 233 * AUTO_SLEEP: A '1' sets the ADXL34x to switch to Sleep Mode 234 * when inactivity (acceleration has been below inactivity_threshold 235 * for at least inactivity_time) is detected and the LINK bit is set. 236 * A '0' disables automatic switching to Sleep Mode. See the 237 * Sleep Bit section of the ADXL34x datasheet for more information. 238 */ 239 240 #define ADXL_LINK (1 << 5) 241 #define ADXL_AUTO_SLEEP (1 << 4) 242 243 u8 power_mode; 244 245 /* 246 * fifo_mode: 247 * BYPASS The FIFO is bypassed 248 * FIFO FIFO collects up to 32 values then stops collecting data 249 * STREAM FIFO holds the last 32 data values. Once full, the FIFO's 250 * oldest data is lost as it is replaced with newer data 251 * 252 * DEFAULT should be ADXL_FIFO_STREAM 253 */ 254 255 #define ADXL_FIFO_BYPASS 0 256 #define ADXL_FIFO_FIFO 1 257 #define ADXL_FIFO_STREAM 2 258 259 u8 fifo_mode; 260 261 /* 262 * watermark: 263 * The Watermark feature can be used to reduce the interrupt load 264 * of the system. The FIFO fills up to the value stored in watermark 265 * [1..32] and then generates an interrupt. 266 * A '0' disables the watermark feature. 267 */ 268 269 u8 watermark; 270 271 /* 272 * When acceleration measurements are received from the ADXL34x 273 * events are sent to the event subsystem. The following settings 274 * select the event type and event code for new x, y and z axis data 275 * respectively. 276 */ 277 u32 ev_type; /* EV_ABS or EV_REL */ 278 279 u32 ev_code_x; /* ABS_X,Y,Z or REL_X,Y,Z */ 280 u32 ev_code_y; /* ABS_X,Y,Z or REL_X,Y,Z */ 281 u32 ev_code_z; /* ABS_X,Y,Z or REL_X,Y,Z */ 282 283 /* 284 * A valid BTN or KEY Code; use tap_axis_control to disable 285 * event reporting 286 */ 287 288 u32 ev_code_tap[3]; /* EV_KEY {X-Axis, Y-Axis, Z-Axis} */ 289 290 /* 291 * A valid BTN or KEY Code for Free-Fall or Activity enables 292 * input event reporting. A '0' disables the Free-Fall or 293 * Activity reporting. 294 */ 295 296 u32 ev_code_ff; /* EV_KEY */ 297 u32 ev_code_act_inactivity; /* EV_KEY */ 298 299 /* 300 * Use ADXL34x INT2 pin instead of INT1 pin for interrupt output 301 */ 302 u8 use_int2; 303 304 /* 305 * ADXL346 only ORIENTATION SENSING feature 306 * The orientation function of the ADXL346 reports both 2-D and 307 * 3-D orientation concurrently. 308 */ 309 310 #define ADXL_EN_ORIENTATION_2D 1 311 #define ADXL_EN_ORIENTATION_3D 2 312 #define ADXL_EN_ORIENTATION_2D_3D 3 313 314 u8 orientation_enable; 315 316 /* 317 * The width of the deadzone region between two or more 318 * orientation positions is determined by setting the Deadzone 319 * value. The deadzone region size can be specified with a 320 * resolution of 3.6deg. The deadzone angle represents the total 321 * angle where the orientation is considered invalid. 322 */ 323 324 #define ADXL_DEADZONE_ANGLE_0p0 0 /* !!!0.0 [deg] */ 325 #define ADXL_DEADZONE_ANGLE_3p6 1 /* 3.6 [deg] */ 326 #define ADXL_DEADZONE_ANGLE_7p2 2 /* 7.2 [deg] */ 327 #define ADXL_DEADZONE_ANGLE_10p8 3 /* 10.8 [deg] */ 328 #define ADXL_DEADZONE_ANGLE_14p4 4 /* 14.4 [deg] */ 329 #define ADXL_DEADZONE_ANGLE_18p0 5 /* 18.0 [deg] */ 330 #define ADXL_DEADZONE_ANGLE_21p6 6 /* 21.6 [deg] */ 331 #define ADXL_DEADZONE_ANGLE_25p2 7 /* 25.2 [deg] */ 332 333 u8 deadzone_angle; 334 335 /* 336 * To eliminate most human motion such as walking or shaking, 337 * a Divisor value should be selected to effectively limit the 338 * orientation bandwidth. Set the depth of the filter used to 339 * low-pass filter the measured acceleration for stable 340 * orientation sensing 341 */ 342 343 #define ADXL_LP_FILTER_DIVISOR_2 0 344 #define ADXL_LP_FILTER_DIVISOR_4 1 345 #define ADXL_LP_FILTER_DIVISOR_8 2 346 #define ADXL_LP_FILTER_DIVISOR_16 3 347 #define ADXL_LP_FILTER_DIVISOR_32 4 348 #define ADXL_LP_FILTER_DIVISOR_64 5 349 #define ADXL_LP_FILTER_DIVISOR_128 6 350 #define ADXL_LP_FILTER_DIVISOR_256 7 351 352 u8 divisor_length; 353 354 u32 ev_codes_orient_2d[4]; /* EV_KEY {+X, -X, +Y, -Y} */ 355 u32 ev_codes_orient_3d[6]; /* EV_KEY {+Z, +Y, +X, -X, -Y, -Z} */ 356 }; 357 #endif 358