1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* 3 * i2c.h - definitions for the Linux i2c bus interface 4 * Copyright (C) 1995-2000 Simon G. Vogl 5 * Copyright (C) 2013-2019 Wolfram Sang <wsa@kernel.org> 6 * 7 * With some changes from Kyösti Mälkki <kmalkki@cc.hut.fi> and 8 * Frodo Looijaard <frodol@dds.nl> 9 */ 10 #ifndef _LINUX_I2C_H 11 #define _LINUX_I2C_H 12 13 #include <linux/acpi.h> /* for acpi_handle */ 14 #include <linux/mod_devicetable.h> 15 #include <linux/device.h> /* for struct device */ 16 #include <linux/sched.h> /* for completion */ 17 #include <linux/mutex.h> 18 #include <linux/rtmutex.h> 19 #include <linux/irqdomain.h> /* for Host Notify IRQ */ 20 #include <linux/of.h> /* for struct device_node */ 21 #include <linux/swab.h> /* for swab16 */ 22 #include <uapi/linux/i2c.h> 23 24 extern struct bus_type i2c_bus_type; 25 extern struct device_type i2c_adapter_type; 26 extern struct device_type i2c_client_type; 27 28 /* --- General options ------------------------------------------------ */ 29 30 struct i2c_msg; 31 struct i2c_algorithm; 32 struct i2c_adapter; 33 struct i2c_client; 34 struct i2c_driver; 35 struct i2c_device_identity; 36 union i2c_smbus_data; 37 struct i2c_board_info; 38 enum i2c_slave_event; 39 typedef int (*i2c_slave_cb_t)(struct i2c_client *client, 40 enum i2c_slave_event event, u8 *val); 41 42 /* I2C Frequency Modes */ 43 #define I2C_MAX_STANDARD_MODE_FREQ 100000 44 #define I2C_MAX_FAST_MODE_FREQ 400000 45 #define I2C_MAX_FAST_MODE_PLUS_FREQ 1000000 46 #define I2C_MAX_TURBO_MODE_FREQ 1400000 47 #define I2C_MAX_HIGH_SPEED_MODE_FREQ 3400000 48 #define I2C_MAX_ULTRA_FAST_MODE_FREQ 5000000 49 50 struct module; 51 struct property_entry; 52 53 #if IS_ENABLED(CONFIG_I2C) 54 /* 55 * The master routines are the ones normally used to transmit data to devices 56 * on a bus (or read from them). Apart from two basic transfer functions to 57 * transmit one message at a time, a more complex version can be used to 58 * transmit an arbitrary number of messages without interruption. 59 * @count must be be less than 64k since msg.len is u16. 60 */ 61 int i2c_transfer_buffer_flags(const struct i2c_client *client, 62 char *buf, int count, u16 flags); 63 64 /** 65 * i2c_master_recv - issue a single I2C message in master receive mode 66 * @client: Handle to slave device 67 * @buf: Where to store data read from slave 68 * @count: How many bytes to read, must be less than 64k since msg.len is u16 69 * 70 * Returns negative errno, or else the number of bytes read. 71 */ 72 static inline int i2c_master_recv(const struct i2c_client *client, 73 char *buf, int count) 74 { 75 return i2c_transfer_buffer_flags(client, buf, count, I2C_M_RD); 76 }; 77 78 /** 79 * i2c_master_recv_dmasafe - issue a single I2C message in master receive mode 80 * using a DMA safe buffer 81 * @client: Handle to slave device 82 * @buf: Where to store data read from slave, must be safe to use with DMA 83 * @count: How many bytes to read, must be less than 64k since msg.len is u16 84 * 85 * Returns negative errno, or else the number of bytes read. 86 */ 87 static inline int i2c_master_recv_dmasafe(const struct i2c_client *client, 88 char *buf, int count) 89 { 90 return i2c_transfer_buffer_flags(client, buf, count, 91 I2C_M_RD | I2C_M_DMA_SAFE); 92 }; 93 94 /** 95 * i2c_master_send - issue a single I2C message in master transmit mode 96 * @client: Handle to slave device 97 * @buf: Data that will be written to the slave 98 * @count: How many bytes to write, must be less than 64k since msg.len is u16 99 * 100 * Returns negative errno, or else the number of bytes written. 101 */ 102 static inline int i2c_master_send(const struct i2c_client *client, 103 const char *buf, int count) 104 { 105 return i2c_transfer_buffer_flags(client, (char *)buf, count, 0); 106 }; 107 108 /** 109 * i2c_master_send_dmasafe - issue a single I2C message in master transmit mode 110 * using a DMA safe buffer 111 * @client: Handle to slave device 112 * @buf: Data that will be written to the slave, must be safe to use with DMA 113 * @count: How many bytes to write, must be less than 64k since msg.len is u16 114 * 115 * Returns negative errno, or else the number of bytes written. 116 */ 117 static inline int i2c_master_send_dmasafe(const struct i2c_client *client, 118 const char *buf, int count) 119 { 120 return i2c_transfer_buffer_flags(client, (char *)buf, count, 121 I2C_M_DMA_SAFE); 122 }; 123 124 /* Transfer num messages. 125 */ 126 int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num); 127 /* Unlocked flavor */ 128 int __i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num); 129 130 /* This is the very generalized SMBus access routine. You probably do not 131 want to use this, though; one of the functions below may be much easier, 132 and probably just as fast. 133 Note that we use i2c_adapter here, because you do not need a specific 134 smbus adapter to call this function. */ 135 s32 i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr, 136 unsigned short flags, char read_write, u8 command, 137 int protocol, union i2c_smbus_data *data); 138 139 /* Unlocked flavor */ 140 s32 __i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr, 141 unsigned short flags, char read_write, u8 command, 142 int protocol, union i2c_smbus_data *data); 143 144 /* Now follow the 'nice' access routines. These also document the calling 145 conventions of i2c_smbus_xfer. */ 146 147 s32 i2c_smbus_read_byte(const struct i2c_client *client); 148 s32 i2c_smbus_write_byte(const struct i2c_client *client, u8 value); 149 s32 i2c_smbus_read_byte_data(const struct i2c_client *client, u8 command); 150 s32 i2c_smbus_write_byte_data(const struct i2c_client *client, 151 u8 command, u8 value); 152 s32 i2c_smbus_read_word_data(const struct i2c_client *client, u8 command); 153 s32 i2c_smbus_write_word_data(const struct i2c_client *client, 154 u8 command, u16 value); 155 156 static inline s32 157 i2c_smbus_read_word_swapped(const struct i2c_client *client, u8 command) 158 { 159 s32 value = i2c_smbus_read_word_data(client, command); 160 161 return (value < 0) ? value : swab16(value); 162 } 163 164 static inline s32 165 i2c_smbus_write_word_swapped(const struct i2c_client *client, 166 u8 command, u16 value) 167 { 168 return i2c_smbus_write_word_data(client, command, swab16(value)); 169 } 170 171 /* Returns the number of read bytes */ 172 s32 i2c_smbus_read_block_data(const struct i2c_client *client, 173 u8 command, u8 *values); 174 s32 i2c_smbus_write_block_data(const struct i2c_client *client, 175 u8 command, u8 length, const u8 *values); 176 /* Returns the number of read bytes */ 177 s32 i2c_smbus_read_i2c_block_data(const struct i2c_client *client, 178 u8 command, u8 length, u8 *values); 179 s32 i2c_smbus_write_i2c_block_data(const struct i2c_client *client, 180 u8 command, u8 length, const u8 *values); 181 s32 i2c_smbus_read_i2c_block_data_or_emulated(const struct i2c_client *client, 182 u8 command, u8 length, 183 u8 *values); 184 int i2c_get_device_id(const struct i2c_client *client, 185 struct i2c_device_identity *id); 186 #endif /* I2C */ 187 188 /** 189 * struct i2c_device_identity - i2c client device identification 190 * @manufacturer_id: 0 - 4095, database maintained by NXP 191 * @part_id: 0 - 511, according to manufacturer 192 * @die_revision: 0 - 7, according to manufacturer 193 */ 194 struct i2c_device_identity { 195 u16 manufacturer_id; 196 #define I2C_DEVICE_ID_NXP_SEMICONDUCTORS 0 197 #define I2C_DEVICE_ID_NXP_SEMICONDUCTORS_1 1 198 #define I2C_DEVICE_ID_NXP_SEMICONDUCTORS_2 2 199 #define I2C_DEVICE_ID_NXP_SEMICONDUCTORS_3 3 200 #define I2C_DEVICE_ID_RAMTRON_INTERNATIONAL 4 201 #define I2C_DEVICE_ID_ANALOG_DEVICES 5 202 #define I2C_DEVICE_ID_STMICROELECTRONICS 6 203 #define I2C_DEVICE_ID_ON_SEMICONDUCTOR 7 204 #define I2C_DEVICE_ID_SPRINTEK_CORPORATION 8 205 #define I2C_DEVICE_ID_ESPROS_PHOTONICS_AG 9 206 #define I2C_DEVICE_ID_FUJITSU_SEMICONDUCTOR 10 207 #define I2C_DEVICE_ID_FLIR 11 208 #define I2C_DEVICE_ID_O2MICRO 12 209 #define I2C_DEVICE_ID_ATMEL 13 210 #define I2C_DEVICE_ID_NONE 0xffff 211 u16 part_id; 212 u8 die_revision; 213 }; 214 215 enum i2c_alert_protocol { 216 I2C_PROTOCOL_SMBUS_ALERT, 217 I2C_PROTOCOL_SMBUS_HOST_NOTIFY, 218 }; 219 220 /** 221 * struct i2c_driver - represent an I2C device driver 222 * @class: What kind of i2c device we instantiate (for detect) 223 * @probe: Callback for device binding - soon to be deprecated 224 * @probe_new: New callback for device binding 225 * @remove: Callback for device unbinding 226 * @shutdown: Callback for device shutdown 227 * @alert: Alert callback, for example for the SMBus alert protocol 228 * @command: Callback for bus-wide signaling (optional) 229 * @driver: Device driver model driver 230 * @id_table: List of I2C devices supported by this driver 231 * @detect: Callback for device detection 232 * @address_list: The I2C addresses to probe (for detect) 233 * @clients: List of detected clients we created (for i2c-core use only) 234 * @disable_i2c_core_irq_mapping: Tell the i2c-core to not do irq-mapping 235 * 236 * The driver.owner field should be set to the module owner of this driver. 237 * The driver.name field should be set to the name of this driver. 238 * 239 * For automatic device detection, both @detect and @address_list must 240 * be defined. @class should also be set, otherwise only devices forced 241 * with module parameters will be created. The detect function must 242 * fill at least the name field of the i2c_board_info structure it is 243 * handed upon successful detection, and possibly also the flags field. 244 * 245 * If @detect is missing, the driver will still work fine for enumerated 246 * devices. Detected devices simply won't be supported. This is expected 247 * for the many I2C/SMBus devices which can't be detected reliably, and 248 * the ones which can always be enumerated in practice. 249 * 250 * The i2c_client structure which is handed to the @detect callback is 251 * not a real i2c_client. It is initialized just enough so that you can 252 * call i2c_smbus_read_byte_data and friends on it. Don't do anything 253 * else with it. In particular, calling dev_dbg and friends on it is 254 * not allowed. 255 */ 256 struct i2c_driver { 257 unsigned int class; 258 259 /* Standard driver model interfaces */ 260 int (*probe)(struct i2c_client *client, const struct i2c_device_id *id); 261 int (*remove)(struct i2c_client *client); 262 263 /* New driver model interface to aid the seamless removal of the 264 * current probe()'s, more commonly unused than used second parameter. 265 */ 266 int (*probe_new)(struct i2c_client *client); 267 268 /* driver model interfaces that don't relate to enumeration */ 269 void (*shutdown)(struct i2c_client *client); 270 271 /* Alert callback, for example for the SMBus alert protocol. 272 * The format and meaning of the data value depends on the protocol. 273 * For the SMBus alert protocol, there is a single bit of data passed 274 * as the alert response's low bit ("event flag"). 275 * For the SMBus Host Notify protocol, the data corresponds to the 276 * 16-bit payload data reported by the slave device acting as master. 277 */ 278 void (*alert)(struct i2c_client *client, enum i2c_alert_protocol protocol, 279 unsigned int data); 280 281 /* a ioctl like command that can be used to perform specific functions 282 * with the device. 283 */ 284 int (*command)(struct i2c_client *client, unsigned int cmd, void *arg); 285 286 struct device_driver driver; 287 const struct i2c_device_id *id_table; 288 289 /* Device detection callback for automatic device creation */ 290 int (*detect)(struct i2c_client *client, struct i2c_board_info *info); 291 const unsigned short *address_list; 292 struct list_head clients; 293 294 bool disable_i2c_core_irq_mapping; 295 }; 296 #define to_i2c_driver(d) container_of(d, struct i2c_driver, driver) 297 298 /** 299 * struct i2c_client - represent an I2C slave device 300 * @flags: see I2C_CLIENT_* for possible flags 301 * @addr: Address used on the I2C bus connected to the parent adapter. 302 * @name: Indicates the type of the device, usually a chip name that's 303 * generic enough to hide second-sourcing and compatible revisions. 304 * @adapter: manages the bus segment hosting this I2C device 305 * @dev: Driver model device node for the slave. 306 * @init_irq: IRQ that was set at initialization 307 * @irq: indicates the IRQ generated by this device (if any) 308 * @detected: member of an i2c_driver.clients list or i2c-core's 309 * userspace_devices list 310 * @slave_cb: Callback when I2C slave mode of an adapter is used. The adapter 311 * calls it to pass on slave events to the slave driver. 312 * 313 * An i2c_client identifies a single device (i.e. chip) connected to an 314 * i2c bus. The behaviour exposed to Linux is defined by the driver 315 * managing the device. 316 */ 317 struct i2c_client { 318 unsigned short flags; /* div., see below */ 319 #define I2C_CLIENT_PEC 0x04 /* Use Packet Error Checking */ 320 #define I2C_CLIENT_TEN 0x10 /* we have a ten bit chip address */ 321 /* Must equal I2C_M_TEN below */ 322 #define I2C_CLIENT_SLAVE 0x20 /* we are the slave */ 323 #define I2C_CLIENT_HOST_NOTIFY 0x40 /* We want to use I2C host notify */ 324 #define I2C_CLIENT_WAKE 0x80 /* for board_info; true iff can wake */ 325 #define I2C_CLIENT_SCCB 0x9000 /* Use Omnivision SCCB protocol */ 326 /* Must match I2C_M_STOP|IGNORE_NAK */ 327 328 unsigned short addr; /* chip address - NOTE: 7bit */ 329 /* addresses are stored in the */ 330 /* _LOWER_ 7 bits */ 331 char name[I2C_NAME_SIZE]; 332 struct i2c_adapter *adapter; /* the adapter we sit on */ 333 struct device dev; /* the device structure */ 334 int init_irq; /* irq set at initialization */ 335 int irq; /* irq issued by device */ 336 struct list_head detected; 337 #if IS_ENABLED(CONFIG_I2C_SLAVE) 338 i2c_slave_cb_t slave_cb; /* callback for slave mode */ 339 #endif 340 }; 341 #define to_i2c_client(d) container_of(d, struct i2c_client, dev) 342 343 struct i2c_client *i2c_verify_client(struct device *dev); 344 struct i2c_adapter *i2c_verify_adapter(struct device *dev); 345 const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id, 346 const struct i2c_client *client); 347 348 static inline struct i2c_client *kobj_to_i2c_client(struct kobject *kobj) 349 { 350 struct device * const dev = container_of(kobj, struct device, kobj); 351 return to_i2c_client(dev); 352 } 353 354 static inline void *i2c_get_clientdata(const struct i2c_client *dev) 355 { 356 return dev_get_drvdata(&dev->dev); 357 } 358 359 static inline void i2c_set_clientdata(struct i2c_client *dev, void *data) 360 { 361 dev_set_drvdata(&dev->dev, data); 362 } 363 364 /* I2C slave support */ 365 366 #if IS_ENABLED(CONFIG_I2C_SLAVE) 367 enum i2c_slave_event { 368 I2C_SLAVE_READ_REQUESTED, 369 I2C_SLAVE_WRITE_REQUESTED, 370 I2C_SLAVE_READ_PROCESSED, 371 I2C_SLAVE_WRITE_RECEIVED, 372 I2C_SLAVE_STOP, 373 }; 374 375 int i2c_slave_register(struct i2c_client *client, i2c_slave_cb_t slave_cb); 376 int i2c_slave_unregister(struct i2c_client *client); 377 bool i2c_detect_slave_mode(struct device *dev); 378 379 static inline int i2c_slave_event(struct i2c_client *client, 380 enum i2c_slave_event event, u8 *val) 381 { 382 return client->slave_cb(client, event, val); 383 } 384 #else 385 static inline bool i2c_detect_slave_mode(struct device *dev) { return false; } 386 #endif 387 388 /** 389 * struct i2c_board_info - template for device creation 390 * @type: chip type, to initialize i2c_client.name 391 * @flags: to initialize i2c_client.flags 392 * @addr: stored in i2c_client.addr 393 * @dev_name: Overrides the default <busnr>-<addr> dev_name if set 394 * @platform_data: stored in i2c_client.dev.platform_data 395 * @of_node: pointer to OpenFirmware device node 396 * @fwnode: device node supplied by the platform firmware 397 * @properties: additional device properties for the device 398 * @resources: resources associated with the device 399 * @num_resources: number of resources in the @resources array 400 * @irq: stored in i2c_client.irq 401 * 402 * I2C doesn't actually support hardware probing, although controllers and 403 * devices may be able to use I2C_SMBUS_QUICK to tell whether or not there's 404 * a device at a given address. Drivers commonly need more information than 405 * that, such as chip type, configuration, associated IRQ, and so on. 406 * 407 * i2c_board_info is used to build tables of information listing I2C devices 408 * that are present. This information is used to grow the driver model tree. 409 * For mainboards this is done statically using i2c_register_board_info(); 410 * bus numbers identify adapters that aren't yet available. For add-on boards, 411 * i2c_new_device() does this dynamically with the adapter already known. 412 */ 413 struct i2c_board_info { 414 char type[I2C_NAME_SIZE]; 415 unsigned short flags; 416 unsigned short addr; 417 const char *dev_name; 418 void *platform_data; 419 struct device_node *of_node; 420 struct fwnode_handle *fwnode; 421 const struct property_entry *properties; 422 const struct resource *resources; 423 unsigned int num_resources; 424 int irq; 425 }; 426 427 /** 428 * I2C_BOARD_INFO - macro used to list an i2c device and its address 429 * @dev_type: identifies the device type 430 * @dev_addr: the device's address on the bus. 431 * 432 * This macro initializes essential fields of a struct i2c_board_info, 433 * declaring what has been provided on a particular board. Optional 434 * fields (such as associated irq, or device-specific platform_data) 435 * are provided using conventional syntax. 436 */ 437 #define I2C_BOARD_INFO(dev_type, dev_addr) \ 438 .type = dev_type, .addr = (dev_addr) 439 440 441 #if IS_ENABLED(CONFIG_I2C) 442 /* Add-on boards should register/unregister their devices; e.g. a board 443 * with integrated I2C, a config eeprom, sensors, and a codec that's 444 * used in conjunction with the primary hardware. 445 */ 446 struct i2c_client * 447 i2c_new_device(struct i2c_adapter *adap, struct i2c_board_info const *info); 448 449 struct i2c_client * 450 i2c_new_client_device(struct i2c_adapter *adap, struct i2c_board_info const *info); 451 452 /* If you don't know the exact address of an I2C device, use this variant 453 * instead, which can probe for device presence in a list of possible 454 * addresses. The "probe" callback function is optional. If it is provided, 455 * it must return 1 on successful probe, 0 otherwise. If it is not provided, 456 * a default probing method is used. 457 */ 458 struct i2c_client * 459 i2c_new_scanned_device(struct i2c_adapter *adap, 460 struct i2c_board_info *info, 461 unsigned short const *addr_list, 462 int (*probe)(struct i2c_adapter *adap, unsigned short addr)); 463 464 /* Common custom probe functions */ 465 int i2c_probe_func_quick_read(struct i2c_adapter *adap, unsigned short addr); 466 467 struct i2c_client * 468 i2c_new_dummy_device(struct i2c_adapter *adapter, u16 address); 469 470 struct i2c_client * 471 devm_i2c_new_dummy_device(struct device *dev, struct i2c_adapter *adap, u16 address); 472 473 struct i2c_client * 474 i2c_new_ancillary_device(struct i2c_client *client, 475 const char *name, 476 u16 default_addr); 477 478 void i2c_unregister_device(struct i2c_client *client); 479 #endif /* I2C */ 480 481 /* Mainboard arch_initcall() code should register all its I2C devices. 482 * This is done at arch_initcall time, before declaring any i2c adapters. 483 * Modules for add-on boards must use other calls. 484 */ 485 #ifdef CONFIG_I2C_BOARDINFO 486 int 487 i2c_register_board_info(int busnum, struct i2c_board_info const *info, 488 unsigned n); 489 #else 490 static inline int 491 i2c_register_board_info(int busnum, struct i2c_board_info const *info, 492 unsigned n) 493 { 494 return 0; 495 } 496 #endif /* I2C_BOARDINFO */ 497 498 /** 499 * struct i2c_algorithm - represent I2C transfer method 500 * @master_xfer: Issue a set of i2c transactions to the given I2C adapter 501 * defined by the msgs array, with num messages available to transfer via 502 * the adapter specified by adap. 503 * @master_xfer_atomic: same as @master_xfer. Yet, only using atomic context 504 * so e.g. PMICs can be accessed very late before shutdown. Optional. 505 * @smbus_xfer: Issue smbus transactions to the given I2C adapter. If this 506 * is not present, then the bus layer will try and convert the SMBus calls 507 * into I2C transfers instead. 508 * @smbus_xfer_atomic: same as @smbus_xfer. Yet, only using atomic context 509 * so e.g. PMICs can be accessed very late before shutdown. Optional. 510 * @functionality: Return the flags that this algorithm/adapter pair supports 511 * from the ``I2C_FUNC_*`` flags. 512 * @reg_slave: Register given client to I2C slave mode of this adapter 513 * @unreg_slave: Unregister given client from I2C slave mode of this adapter 514 * 515 * The following structs are for those who like to implement new bus drivers: 516 * i2c_algorithm is the interface to a class of hardware solutions which can 517 * be addressed using the same bus algorithms - i.e. bit-banging or the PCF8584 518 * to name two of the most common. 519 * 520 * The return codes from the ``master_xfer{_atomic}`` fields should indicate the 521 * type of error code that occurred during the transfer, as documented in the 522 * Kernel Documentation file Documentation/i2c/fault-codes.rst. 523 */ 524 struct i2c_algorithm { 525 /* 526 * If an adapter algorithm can't do I2C-level access, set master_xfer 527 * to NULL. If an adapter algorithm can do SMBus access, set 528 * smbus_xfer. If set to NULL, the SMBus protocol is simulated 529 * using common I2C messages. 530 * 531 * master_xfer should return the number of messages successfully 532 * processed, or a negative value on error 533 */ 534 int (*master_xfer)(struct i2c_adapter *adap, struct i2c_msg *msgs, 535 int num); 536 int (*master_xfer_atomic)(struct i2c_adapter *adap, 537 struct i2c_msg *msgs, int num); 538 int (*smbus_xfer)(struct i2c_adapter *adap, u16 addr, 539 unsigned short flags, char read_write, 540 u8 command, int size, union i2c_smbus_data *data); 541 int (*smbus_xfer_atomic)(struct i2c_adapter *adap, u16 addr, 542 unsigned short flags, char read_write, 543 u8 command, int size, union i2c_smbus_data *data); 544 545 /* To determine what the adapter supports */ 546 u32 (*functionality)(struct i2c_adapter *adap); 547 548 #if IS_ENABLED(CONFIG_I2C_SLAVE) 549 int (*reg_slave)(struct i2c_client *client); 550 int (*unreg_slave)(struct i2c_client *client); 551 #endif 552 }; 553 554 /** 555 * struct i2c_lock_operations - represent I2C locking operations 556 * @lock_bus: Get exclusive access to an I2C bus segment 557 * @trylock_bus: Try to get exclusive access to an I2C bus segment 558 * @unlock_bus: Release exclusive access to an I2C bus segment 559 * 560 * The main operations are wrapped by i2c_lock_bus and i2c_unlock_bus. 561 */ 562 struct i2c_lock_operations { 563 void (*lock_bus)(struct i2c_adapter *adapter, unsigned int flags); 564 int (*trylock_bus)(struct i2c_adapter *adapter, unsigned int flags); 565 void (*unlock_bus)(struct i2c_adapter *adapter, unsigned int flags); 566 }; 567 568 /** 569 * struct i2c_timings - I2C timing information 570 * @bus_freq_hz: the bus frequency in Hz 571 * @scl_rise_ns: time SCL signal takes to rise in ns; t(r) in the I2C specification 572 * @scl_fall_ns: time SCL signal takes to fall in ns; t(f) in the I2C specification 573 * @scl_int_delay_ns: time IP core additionally needs to setup SCL in ns 574 * @sda_fall_ns: time SDA signal takes to fall in ns; t(f) in the I2C specification 575 * @sda_hold_ns: time IP core additionally needs to hold SDA in ns 576 * @digital_filter_width_ns: width in ns of spikes on i2c lines that the IP core 577 * digital filter can filter out 578 * @analog_filter_cutoff_freq_hz: threshold frequency for the low pass IP core 579 * analog filter 580 */ 581 struct i2c_timings { 582 u32 bus_freq_hz; 583 u32 scl_rise_ns; 584 u32 scl_fall_ns; 585 u32 scl_int_delay_ns; 586 u32 sda_fall_ns; 587 u32 sda_hold_ns; 588 u32 digital_filter_width_ns; 589 u32 analog_filter_cutoff_freq_hz; 590 }; 591 592 /** 593 * struct i2c_bus_recovery_info - I2C bus recovery information 594 * @recover_bus: Recover routine. Either pass driver's recover_bus() routine, or 595 * i2c_generic_scl_recovery(). 596 * @get_scl: This gets current value of SCL line. Mandatory for generic SCL 597 * recovery. Populated internally for generic GPIO recovery. 598 * @set_scl: This sets/clears the SCL line. Mandatory for generic SCL recovery. 599 * Populated internally for generic GPIO recovery. 600 * @get_sda: This gets current value of SDA line. This or set_sda() is mandatory 601 * for generic SCL recovery. Populated internally, if sda_gpio is a valid 602 * GPIO, for generic GPIO recovery. 603 * @set_sda: This sets/clears the SDA line. This or get_sda() is mandatory for 604 * generic SCL recovery. Populated internally, if sda_gpio is a valid GPIO, 605 * for generic GPIO recovery. 606 * @get_bus_free: Returns the bus free state as seen from the IP core in case it 607 * has a more complex internal logic than just reading SDA. Optional. 608 * @prepare_recovery: This will be called before starting recovery. Platform may 609 * configure padmux here for SDA/SCL line or something else they want. 610 * @unprepare_recovery: This will be called after completing recovery. Platform 611 * may configure padmux here for SDA/SCL line or something else they want. 612 * @scl_gpiod: gpiod of the SCL line. Only required for GPIO recovery. 613 * @sda_gpiod: gpiod of the SDA line. Only required for GPIO recovery. 614 */ 615 struct i2c_bus_recovery_info { 616 int (*recover_bus)(struct i2c_adapter *adap); 617 618 int (*get_scl)(struct i2c_adapter *adap); 619 void (*set_scl)(struct i2c_adapter *adap, int val); 620 int (*get_sda)(struct i2c_adapter *adap); 621 void (*set_sda)(struct i2c_adapter *adap, int val); 622 int (*get_bus_free)(struct i2c_adapter *adap); 623 624 void (*prepare_recovery)(struct i2c_adapter *adap); 625 void (*unprepare_recovery)(struct i2c_adapter *adap); 626 627 /* gpio recovery */ 628 struct gpio_desc *scl_gpiod; 629 struct gpio_desc *sda_gpiod; 630 }; 631 632 int i2c_recover_bus(struct i2c_adapter *adap); 633 634 /* Generic recovery routines */ 635 int i2c_generic_scl_recovery(struct i2c_adapter *adap); 636 637 /** 638 * struct i2c_adapter_quirks - describe flaws of an i2c adapter 639 * @flags: see I2C_AQ_* for possible flags and read below 640 * @max_num_msgs: maximum number of messages per transfer 641 * @max_write_len: maximum length of a write message 642 * @max_read_len: maximum length of a read message 643 * @max_comb_1st_msg_len: maximum length of the first msg in a combined message 644 * @max_comb_2nd_msg_len: maximum length of the second msg in a combined message 645 * 646 * Note about combined messages: Some I2C controllers can only send one message 647 * per transfer, plus something called combined message or write-then-read. 648 * This is (usually) a small write message followed by a read message and 649 * barely enough to access register based devices like EEPROMs. There is a flag 650 * to support this mode. It implies max_num_msg = 2 and does the length checks 651 * with max_comb_*_len because combined message mode usually has its own 652 * limitations. Because of HW implementations, some controllers can actually do 653 * write-then-anything or other variants. To support that, write-then-read has 654 * been broken out into smaller bits like write-first and read-second which can 655 * be combined as needed. 656 */ 657 658 struct i2c_adapter_quirks { 659 u64 flags; 660 int max_num_msgs; 661 u16 max_write_len; 662 u16 max_read_len; 663 u16 max_comb_1st_msg_len; 664 u16 max_comb_2nd_msg_len; 665 }; 666 667 /* enforce max_num_msgs = 2 and use max_comb_*_len for length checks */ 668 #define I2C_AQ_COMB BIT(0) 669 /* first combined message must be write */ 670 #define I2C_AQ_COMB_WRITE_FIRST BIT(1) 671 /* second combined message must be read */ 672 #define I2C_AQ_COMB_READ_SECOND BIT(2) 673 /* both combined messages must have the same target address */ 674 #define I2C_AQ_COMB_SAME_ADDR BIT(3) 675 /* convenience macro for typical write-then read case */ 676 #define I2C_AQ_COMB_WRITE_THEN_READ (I2C_AQ_COMB | I2C_AQ_COMB_WRITE_FIRST | \ 677 I2C_AQ_COMB_READ_SECOND | I2C_AQ_COMB_SAME_ADDR) 678 /* clock stretching is not supported */ 679 #define I2C_AQ_NO_CLK_STRETCH BIT(4) 680 /* message cannot have length of 0 */ 681 #define I2C_AQ_NO_ZERO_LEN_READ BIT(5) 682 #define I2C_AQ_NO_ZERO_LEN_WRITE BIT(6) 683 #define I2C_AQ_NO_ZERO_LEN (I2C_AQ_NO_ZERO_LEN_READ | I2C_AQ_NO_ZERO_LEN_WRITE) 684 685 /* 686 * i2c_adapter is the structure used to identify a physical i2c bus along 687 * with the access algorithms necessary to access it. 688 */ 689 struct i2c_adapter { 690 struct module *owner; 691 unsigned int class; /* classes to allow probing for */ 692 const struct i2c_algorithm *algo; /* the algorithm to access the bus */ 693 void *algo_data; 694 695 /* data fields that are valid for all devices */ 696 const struct i2c_lock_operations *lock_ops; 697 struct rt_mutex bus_lock; 698 struct rt_mutex mux_lock; 699 700 int timeout; /* in jiffies */ 701 int retries; 702 struct device dev; /* the adapter device */ 703 unsigned long locked_flags; /* owned by the I2C core */ 704 #define I2C_ALF_IS_SUSPENDED 0 705 #define I2C_ALF_SUSPEND_REPORTED 1 706 707 int nr; 708 char name[48]; 709 struct completion dev_released; 710 711 struct mutex userspace_clients_lock; 712 struct list_head userspace_clients; 713 714 struct i2c_bus_recovery_info *bus_recovery_info; 715 const struct i2c_adapter_quirks *quirks; 716 717 struct irq_domain *host_notify_domain; 718 }; 719 #define to_i2c_adapter(d) container_of(d, struct i2c_adapter, dev) 720 721 static inline void *i2c_get_adapdata(const struct i2c_adapter *adap) 722 { 723 return dev_get_drvdata(&adap->dev); 724 } 725 726 static inline void i2c_set_adapdata(struct i2c_adapter *adap, void *data) 727 { 728 dev_set_drvdata(&adap->dev, data); 729 } 730 731 static inline struct i2c_adapter * 732 i2c_parent_is_i2c_adapter(const struct i2c_adapter *adapter) 733 { 734 #if IS_ENABLED(CONFIG_I2C_MUX) 735 struct device *parent = adapter->dev.parent; 736 737 if (parent != NULL && parent->type == &i2c_adapter_type) 738 return to_i2c_adapter(parent); 739 else 740 #endif 741 return NULL; 742 } 743 744 int i2c_for_each_dev(void *data, int (*fn)(struct device *dev, void *data)); 745 746 /* Adapter locking functions, exported for shared pin cases */ 747 #define I2C_LOCK_ROOT_ADAPTER BIT(0) 748 #define I2C_LOCK_SEGMENT BIT(1) 749 750 /** 751 * i2c_lock_bus - Get exclusive access to an I2C bus segment 752 * @adapter: Target I2C bus segment 753 * @flags: I2C_LOCK_ROOT_ADAPTER locks the root i2c adapter, I2C_LOCK_SEGMENT 754 * locks only this branch in the adapter tree 755 */ 756 static inline void 757 i2c_lock_bus(struct i2c_adapter *adapter, unsigned int flags) 758 { 759 adapter->lock_ops->lock_bus(adapter, flags); 760 } 761 762 /** 763 * i2c_trylock_bus - Try to get exclusive access to an I2C bus segment 764 * @adapter: Target I2C bus segment 765 * @flags: I2C_LOCK_ROOT_ADAPTER tries to locks the root i2c adapter, 766 * I2C_LOCK_SEGMENT tries to lock only this branch in the adapter tree 767 * 768 * Return: true if the I2C bus segment is locked, false otherwise 769 */ 770 static inline int 771 i2c_trylock_bus(struct i2c_adapter *adapter, unsigned int flags) 772 { 773 return adapter->lock_ops->trylock_bus(adapter, flags); 774 } 775 776 /** 777 * i2c_unlock_bus - Release exclusive access to an I2C bus segment 778 * @adapter: Target I2C bus segment 779 * @flags: I2C_LOCK_ROOT_ADAPTER unlocks the root i2c adapter, I2C_LOCK_SEGMENT 780 * unlocks only this branch in the adapter tree 781 */ 782 static inline void 783 i2c_unlock_bus(struct i2c_adapter *adapter, unsigned int flags) 784 { 785 adapter->lock_ops->unlock_bus(adapter, flags); 786 } 787 788 /** 789 * i2c_mark_adapter_suspended - Report suspended state of the adapter to the core 790 * @adap: Adapter to mark as suspended 791 * 792 * When using this helper to mark an adapter as suspended, the core will reject 793 * further transfers to this adapter. The usage of this helper is optional but 794 * recommended for devices having distinct handlers for system suspend and 795 * runtime suspend. More complex devices are free to implement custom solutions 796 * to reject transfers when suspended. 797 */ 798 static inline void i2c_mark_adapter_suspended(struct i2c_adapter *adap) 799 { 800 i2c_lock_bus(adap, I2C_LOCK_ROOT_ADAPTER); 801 set_bit(I2C_ALF_IS_SUSPENDED, &adap->locked_flags); 802 i2c_unlock_bus(adap, I2C_LOCK_ROOT_ADAPTER); 803 } 804 805 /** 806 * i2c_mark_adapter_resumed - Report resumed state of the adapter to the core 807 * @adap: Adapter to mark as resumed 808 * 809 * When using this helper to mark an adapter as resumed, the core will allow 810 * further transfers to this adapter. See also further notes to 811 * @i2c_mark_adapter_suspended(). 812 */ 813 static inline void i2c_mark_adapter_resumed(struct i2c_adapter *adap) 814 { 815 i2c_lock_bus(adap, I2C_LOCK_ROOT_ADAPTER); 816 clear_bit(I2C_ALF_IS_SUSPENDED, &adap->locked_flags); 817 i2c_unlock_bus(adap, I2C_LOCK_ROOT_ADAPTER); 818 } 819 820 /* i2c adapter classes (bitmask) */ 821 #define I2C_CLASS_HWMON (1<<0) /* lm_sensors, ... */ 822 #define I2C_CLASS_DDC (1<<3) /* DDC bus on graphics adapters */ 823 #define I2C_CLASS_SPD (1<<7) /* Memory modules */ 824 /* Warn users that the adapter doesn't support classes anymore */ 825 #define I2C_CLASS_DEPRECATED (1<<8) 826 827 /* Internal numbers to terminate lists */ 828 #define I2C_CLIENT_END 0xfffeU 829 830 /* Construct an I2C_CLIENT_END-terminated array of i2c addresses */ 831 #define I2C_ADDRS(addr, addrs...) \ 832 ((const unsigned short []){ addr, ## addrs, I2C_CLIENT_END }) 833 834 835 /* ----- functions exported by i2c.o */ 836 837 /* administration... 838 */ 839 #if IS_ENABLED(CONFIG_I2C) 840 int i2c_add_adapter(struct i2c_adapter *adap); 841 void i2c_del_adapter(struct i2c_adapter *adap); 842 int i2c_add_numbered_adapter(struct i2c_adapter *adap); 843 844 int i2c_register_driver(struct module *owner, struct i2c_driver *driver); 845 void i2c_del_driver(struct i2c_driver *driver); 846 847 /* use a define to avoid include chaining to get THIS_MODULE */ 848 #define i2c_add_driver(driver) \ 849 i2c_register_driver(THIS_MODULE, driver) 850 851 static inline bool i2c_client_has_driver(struct i2c_client *client) 852 { 853 return !IS_ERR_OR_NULL(client) && client->dev.driver; 854 } 855 856 /* call the i2c_client->command() of all attached clients with 857 * the given arguments */ 858 void i2c_clients_command(struct i2c_adapter *adap, 859 unsigned int cmd, void *arg); 860 861 struct i2c_adapter *i2c_get_adapter(int nr); 862 void i2c_put_adapter(struct i2c_adapter *adap); 863 unsigned int i2c_adapter_depth(struct i2c_adapter *adapter); 864 865 void i2c_parse_fw_timings(struct device *dev, struct i2c_timings *t, bool use_defaults); 866 867 /* Return the functionality mask */ 868 static inline u32 i2c_get_functionality(struct i2c_adapter *adap) 869 { 870 return adap->algo->functionality(adap); 871 } 872 873 /* Return 1 if adapter supports everything we need, 0 if not. */ 874 static inline int i2c_check_functionality(struct i2c_adapter *adap, u32 func) 875 { 876 return (func & i2c_get_functionality(adap)) == func; 877 } 878 879 /** 880 * i2c_check_quirks() - Function for checking the quirk flags in an i2c adapter 881 * @adap: i2c adapter 882 * @quirks: quirk flags 883 * 884 * Return: true if the adapter has all the specified quirk flags, false if not 885 */ 886 static inline bool i2c_check_quirks(struct i2c_adapter *adap, u64 quirks) 887 { 888 if (!adap->quirks) 889 return false; 890 return (adap->quirks->flags & quirks) == quirks; 891 } 892 893 /* Return the adapter number for a specific adapter */ 894 static inline int i2c_adapter_id(struct i2c_adapter *adap) 895 { 896 return adap->nr; 897 } 898 899 static inline u8 i2c_8bit_addr_from_msg(const struct i2c_msg *msg) 900 { 901 return (msg->addr << 1) | (msg->flags & I2C_M_RD ? 1 : 0); 902 } 903 904 u8 *i2c_get_dma_safe_msg_buf(struct i2c_msg *msg, unsigned int threshold); 905 void i2c_put_dma_safe_msg_buf(u8 *buf, struct i2c_msg *msg, bool xferred); 906 907 int i2c_handle_smbus_host_notify(struct i2c_adapter *adap, unsigned short addr); 908 /** 909 * module_i2c_driver() - Helper macro for registering a modular I2C driver 910 * @__i2c_driver: i2c_driver struct 911 * 912 * Helper macro for I2C drivers which do not do anything special in module 913 * init/exit. This eliminates a lot of boilerplate. Each module may only 914 * use this macro once, and calling it replaces module_init() and module_exit() 915 */ 916 #define module_i2c_driver(__i2c_driver) \ 917 module_driver(__i2c_driver, i2c_add_driver, \ 918 i2c_del_driver) 919 920 /** 921 * builtin_i2c_driver() - Helper macro for registering a builtin I2C driver 922 * @__i2c_driver: i2c_driver struct 923 * 924 * Helper macro for I2C drivers which do not do anything special in their 925 * init. This eliminates a lot of boilerplate. Each driver may only 926 * use this macro once, and calling it replaces device_initcall(). 927 */ 928 #define builtin_i2c_driver(__i2c_driver) \ 929 builtin_driver(__i2c_driver, i2c_add_driver) 930 931 #endif /* I2C */ 932 933 #if IS_ENABLED(CONFIG_OF) 934 /* must call put_device() when done with returned i2c_client device */ 935 struct i2c_client *of_find_i2c_device_by_node(struct device_node *node); 936 937 /* must call put_device() when done with returned i2c_adapter device */ 938 struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node); 939 940 /* must call i2c_put_adapter() when done with returned i2c_adapter device */ 941 struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node); 942 943 const struct of_device_id 944 *i2c_of_match_device(const struct of_device_id *matches, 945 struct i2c_client *client); 946 947 int of_i2c_get_board_info(struct device *dev, struct device_node *node, 948 struct i2c_board_info *info); 949 950 #else 951 952 static inline struct i2c_client *of_find_i2c_device_by_node(struct device_node *node) 953 { 954 return NULL; 955 } 956 957 static inline struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node) 958 { 959 return NULL; 960 } 961 962 static inline struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node) 963 { 964 return NULL; 965 } 966 967 static inline const struct of_device_id 968 *i2c_of_match_device(const struct of_device_id *matches, 969 struct i2c_client *client) 970 { 971 return NULL; 972 } 973 974 static inline int of_i2c_get_board_info(struct device *dev, 975 struct device_node *node, 976 struct i2c_board_info *info) 977 { 978 return -ENOTSUPP; 979 } 980 981 #endif /* CONFIG_OF */ 982 983 struct acpi_resource; 984 struct acpi_resource_i2c_serialbus; 985 986 #if IS_ENABLED(CONFIG_ACPI) 987 bool i2c_acpi_get_i2c_resource(struct acpi_resource *ares, 988 struct acpi_resource_i2c_serialbus **i2c); 989 u32 i2c_acpi_find_bus_speed(struct device *dev); 990 struct i2c_client *i2c_acpi_new_device(struct device *dev, int index, 991 struct i2c_board_info *info); 992 struct i2c_adapter *i2c_acpi_find_adapter_by_handle(acpi_handle handle); 993 #else 994 static inline bool i2c_acpi_get_i2c_resource(struct acpi_resource *ares, 995 struct acpi_resource_i2c_serialbus **i2c) 996 { 997 return false; 998 } 999 static inline u32 i2c_acpi_find_bus_speed(struct device *dev) 1000 { 1001 return 0; 1002 } 1003 static inline struct i2c_client *i2c_acpi_new_device(struct device *dev, 1004 int index, struct i2c_board_info *info) 1005 { 1006 return NULL; 1007 } 1008 static inline struct i2c_adapter *i2c_acpi_find_adapter_by_handle(acpi_handle handle) 1009 { 1010 return NULL; 1011 } 1012 #endif /* CONFIG_ACPI */ 1013 1014 #endif /* _LINUX_I2C_H */ 1015