1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #ifndef _LINUX_BRCMPHY_H 3 #define _LINUX_BRCMPHY_H 4 5 #include <linux/phy.h> 6 7 /* All Broadcom Ethernet switches have a pseudo-PHY at address 30 which is used 8 * to configure the switch internal registers via MDIO accesses. 9 */ 10 #define BRCM_PSEUDO_PHY_ADDR 30 11 12 #define PHY_ID_BCM50610 0x0143bd60 13 #define PHY_ID_BCM50610M 0x0143bd70 14 #define PHY_ID_BCM5241 0x0143bc30 15 #define PHY_ID_BCMAC131 0x0143bc70 16 #define PHY_ID_BCM5481 0x0143bca0 17 #define PHY_ID_BCM5395 0x0143bcf0 18 #define PHY_ID_BCM54810 0x03625d00 19 #define PHY_ID_BCM5482 0x0143bcb0 20 #define PHY_ID_BCM5411 0x00206070 21 #define PHY_ID_BCM5421 0x002060e0 22 #define PHY_ID_BCM54210E 0x600d84a0 23 #define PHY_ID_BCM5464 0x002060b0 24 #define PHY_ID_BCM5461 0x002060c0 25 #define PHY_ID_BCM54612E 0x03625e60 26 #define PHY_ID_BCM54616S 0x03625d10 27 #define PHY_ID_BCM57780 0x03625d90 28 #define PHY_ID_BCM89610 0x03625cd0 29 30 #define PHY_ID_BCM7250 0xae025280 31 #define PHY_ID_BCM7255 0xae025120 32 #define PHY_ID_BCM7260 0xae025190 33 #define PHY_ID_BCM7268 0xae025090 34 #define PHY_ID_BCM7271 0xae0253b0 35 #define PHY_ID_BCM7278 0xae0251a0 36 #define PHY_ID_BCM7364 0xae025260 37 #define PHY_ID_BCM7366 0x600d8490 38 #define PHY_ID_BCM7346 0x600d8650 39 #define PHY_ID_BCM7362 0x600d84b0 40 #define PHY_ID_BCM7425 0x600d86b0 41 #define PHY_ID_BCM7429 0x600d8730 42 #define PHY_ID_BCM7435 0x600d8750 43 #define PHY_ID_BCM74371 0xae0252e0 44 #define PHY_ID_BCM7439 0x600d8480 45 #define PHY_ID_BCM7439_2 0xae025080 46 #define PHY_ID_BCM7445 0x600d8510 47 48 #define PHY_ID_BCM_CYGNUS 0xae025200 49 #define PHY_ID_BCM_OMEGA 0xae025100 50 51 #define PHY_BCM_OUI_MASK 0xfffffc00 52 #define PHY_BCM_OUI_1 0x00206000 53 #define PHY_BCM_OUI_2 0x0143bc00 54 #define PHY_BCM_OUI_3 0x03625c00 55 #define PHY_BCM_OUI_4 0x600d8400 56 #define PHY_BCM_OUI_5 0x03625e00 57 #define PHY_BCM_OUI_6 0xae025000 58 59 #define PHY_BCM_FLAGS_MODE_COPPER 0x00000001 60 #define PHY_BCM_FLAGS_MODE_1000BX 0x00000002 61 #define PHY_BCM_FLAGS_INTF_SGMII 0x00000010 62 #define PHY_BCM_FLAGS_INTF_XAUI 0x00000020 63 #define PHY_BRCM_WIRESPEED_ENABLE 0x00000100 64 #define PHY_BRCM_AUTO_PWRDWN_ENABLE 0x00000200 65 #define PHY_BRCM_RX_REFCLK_UNUSED 0x00000400 66 #define PHY_BRCM_STD_IBND_DISABLE 0x00000800 67 #define PHY_BRCM_EXT_IBND_RX_ENABLE 0x00001000 68 #define PHY_BRCM_EXT_IBND_TX_ENABLE 0x00002000 69 #define PHY_BRCM_CLEAR_RGMII_MODE 0x00004000 70 #define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00008000 71 #define PHY_BRCM_EN_MASTER_MODE 0x00010000 72 73 /* Broadcom BCM7xxx specific workarounds */ 74 #define PHY_BRCM_7XXX_REV(x) (((x) >> 8) & 0xff) 75 #define PHY_BRCM_7XXX_PATCH(x) ((x) & 0xff) 76 #define PHY_BCM_FLAGS_VALID 0x80000000 77 78 /* Broadcom BCM54XX register definitions, common to most Broadcom PHYs */ 79 #define MII_BCM54XX_ECR 0x10 /* BCM54xx extended control register */ 80 #define MII_BCM54XX_ECR_IM 0x1000 /* Interrupt mask */ 81 #define MII_BCM54XX_ECR_IF 0x0800 /* Interrupt force */ 82 #define MII_BCM54XX_ECR_FIFOE 0x0001 /* FIFO elasticity */ 83 84 #define MII_BCM54XX_ESR 0x11 /* BCM54xx extended status register */ 85 #define MII_BCM54XX_ESR_IS 0x1000 /* Interrupt status */ 86 87 #define MII_BCM54XX_EXP_DATA 0x15 /* Expansion register data */ 88 #define MII_BCM54XX_EXP_SEL 0x17 /* Expansion register select */ 89 #define MII_BCM54XX_EXP_SEL_SSD 0x0e00 /* Secondary SerDes select */ 90 #define MII_BCM54XX_EXP_SEL_ER 0x0f00 /* Expansion register select */ 91 #define MII_BCM54XX_EXP_SEL_ETC 0x0d00 /* Expansion register spare + 2k mem */ 92 93 #define MII_BCM54XX_AUX_CTL 0x18 /* Auxiliary control register */ 94 #define MII_BCM54XX_ISR 0x1a /* BCM54xx interrupt status register */ 95 #define MII_BCM54XX_IMR 0x1b /* BCM54xx interrupt mask register */ 96 #define MII_BCM54XX_INT_CRCERR 0x0001 /* CRC error */ 97 #define MII_BCM54XX_INT_LINK 0x0002 /* Link status changed */ 98 #define MII_BCM54XX_INT_SPEED 0x0004 /* Link speed change */ 99 #define MII_BCM54XX_INT_DUPLEX 0x0008 /* Duplex mode changed */ 100 #define MII_BCM54XX_INT_LRS 0x0010 /* Local receiver status changed */ 101 #define MII_BCM54XX_INT_RRS 0x0020 /* Remote receiver status changed */ 102 #define MII_BCM54XX_INT_SSERR 0x0040 /* Scrambler synchronization error */ 103 #define MII_BCM54XX_INT_UHCD 0x0080 /* Unsupported HCD negotiated */ 104 #define MII_BCM54XX_INT_NHCD 0x0100 /* No HCD */ 105 #define MII_BCM54XX_INT_NHCDL 0x0200 /* No HCD link */ 106 #define MII_BCM54XX_INT_ANPR 0x0400 /* Auto-negotiation page received */ 107 #define MII_BCM54XX_INT_LC 0x0800 /* All counters below 128 */ 108 #define MII_BCM54XX_INT_HC 0x1000 /* Counter above 32768 */ 109 #define MII_BCM54XX_INT_MDIX 0x2000 /* MDIX status change */ 110 #define MII_BCM54XX_INT_PSERR 0x4000 /* Pair swap error */ 111 112 #define MII_BCM54XX_SHD 0x1c /* 0x1c shadow registers */ 113 #define MII_BCM54XX_SHD_WRITE 0x8000 114 #define MII_BCM54XX_SHD_VAL(x) ((x & 0x1f) << 10) 115 #define MII_BCM54XX_SHD_DATA(x) ((x & 0x3ff) << 0) 116 117 /* 118 * AUXILIARY CONTROL SHADOW ACCESS REGISTERS. (PHY REG 0x18) 119 */ 120 #define MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL 0x00 121 #define MII_BCM54XX_AUXCTL_ACTL_TX_6DB 0x0400 122 #define MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA 0x0800 123 #define MII_BCM54XX_AUXCTL_ACTL_EXT_PKT_LEN 0x4000 124 125 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC 0x07 126 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_WIRESPEED_EN 0x0010 127 #define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN 0x0100 128 #define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX 0x0200 129 #define MII_BCM54XX_AUXCTL_MISC_WREN 0x8000 130 131 #define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT 12 132 #define MII_BCM54XX_AUXCTL_SHDWSEL_MASK 0x0007 133 134 /* 135 * Broadcom LED source encodings. These are used in BCM5461, BCM5481, 136 * BCM5482, and possibly some others. 137 */ 138 #define BCM_LED_SRC_LINKSPD1 0x0 139 #define BCM_LED_SRC_LINKSPD2 0x1 140 #define BCM_LED_SRC_XMITLED 0x2 141 #define BCM_LED_SRC_ACTIVITYLED 0x3 142 #define BCM_LED_SRC_FDXLED 0x4 143 #define BCM_LED_SRC_SLAVE 0x5 144 #define BCM_LED_SRC_INTR 0x6 145 #define BCM_LED_SRC_QUALITY 0x7 146 #define BCM_LED_SRC_RCVLED 0x8 147 #define BCM_LED_SRC_WIRESPEED 0x9 148 #define BCM_LED_SRC_MULTICOLOR1 0xa 149 #define BCM_LED_SRC_OPENSHORT 0xb 150 #define BCM_LED_SRC_OFF 0xe /* Tied high */ 151 #define BCM_LED_SRC_ON 0xf /* Tied low */ 152 153 /* 154 * Broadcom Multicolor LED configurations (expansion register 4) 155 */ 156 #define BCM_EXP_MULTICOLOR (MII_BCM54XX_EXP_SEL_ER + 0x04) 157 #define BCM_LED_MULTICOLOR_IN_PHASE BIT(8) 158 #define BCM_LED_MULTICOLOR_LINK_ACT 0x0 159 #define BCM_LED_MULTICOLOR_SPEED 0x1 160 #define BCM_LED_MULTICOLOR_ACT_FLASH 0x2 161 #define BCM_LED_MULTICOLOR_FDX 0x3 162 #define BCM_LED_MULTICOLOR_OFF 0x4 163 #define BCM_LED_MULTICOLOR_ON 0x5 164 #define BCM_LED_MULTICOLOR_ALT 0x6 165 #define BCM_LED_MULTICOLOR_FLASH 0x7 166 #define BCM_LED_MULTICOLOR_LINK 0x8 167 #define BCM_LED_MULTICOLOR_ACT 0x9 168 #define BCM_LED_MULTICOLOR_PROGRAM 0xa 169 170 /* 171 * BCM5482: Shadow registers 172 * Shadow values go into bits [14:10] of register 0x1c to select a shadow 173 * register to access. 174 */ 175 176 /* 00100: Reserved control register 2 */ 177 #define BCM54XX_SHD_SCR2 0x04 178 #define BCM54XX_SHD_SCR2_WSPD_RTRY_DIS 0x100 179 #define BCM54XX_SHD_SCR2_WSPD_RTRY_LMT_SHIFT 2 180 #define BCM54XX_SHD_SCR2_WSPD_RTRY_LMT_OFFSET 2 181 #define BCM54XX_SHD_SCR2_WSPD_RTRY_LMT_MASK 0x7 182 183 /* 00101: Spare Control Register 3 */ 184 #define BCM54XX_SHD_SCR3 0x05 185 #define BCM54XX_SHD_SCR3_DEF_CLK125 0x0001 186 #define BCM54XX_SHD_SCR3_DLLAPD_DIS 0x0002 187 #define BCM54XX_SHD_SCR3_TRDDAPD 0x0004 188 189 /* 01010: Auto Power-Down */ 190 #define BCM54XX_SHD_APD 0x0a 191 #define BCM_APD_CLR_MASK 0xFE9F /* clear bits 5, 6 & 8 */ 192 #define BCM54XX_SHD_APD_EN 0x0020 193 #define BCM_NO_ANEG_APD_EN 0x0060 /* bits 5 & 6 */ 194 #define BCM_APD_SINGLELP_EN 0x0100 /* Bit 8 */ 195 196 #define BCM5482_SHD_LEDS1 0x0d /* 01101: LED Selector 1 */ 197 /* LED3 / ~LINKSPD[2] selector */ 198 #define BCM5482_SHD_LEDS1_LED3(src) ((src & 0xf) << 4) 199 /* LED1 / ~LINKSPD[1] selector */ 200 #define BCM5482_SHD_LEDS1_LED1(src) ((src & 0xf) << 0) 201 #define BCM54XX_SHD_RGMII_MODE 0x0b /* 01011: RGMII Mode Selector */ 202 #define BCM5482_SHD_SSD 0x14 /* 10100: Secondary SerDes control */ 203 #define BCM5482_SHD_SSD_LEDM 0x0008 /* SSD LED Mode enable */ 204 #define BCM5482_SHD_SSD_EN 0x0001 /* SSD enable */ 205 206 /* 10011: SerDes 100-FX Control Register */ 207 #define BCM54616S_SHD_100FX_CTRL 0x13 208 #define BCM54616S_100FX_MODE BIT(0) /* 100-FX SerDes Enable */ 209 210 /* 11111: Mode Control Register */ 211 #define BCM54XX_SHD_MODE 0x1f 212 #define BCM54XX_SHD_INTF_SEL_MASK GENMASK(2, 1) /* INTERF_SEL[1:0] */ 213 #define BCM54XX_SHD_MODE_1000BX BIT(0) /* Enable 1000-X registers */ 214 215 /* 216 * EXPANSION SHADOW ACCESS REGISTERS. (PHY REG 0x15, 0x16, and 0x17) 217 */ 218 #define MII_BCM54XX_EXP_AADJ1CH0 0x001f 219 #define MII_BCM54XX_EXP_AADJ1CH0_SWP_ABCD_OEN 0x0200 220 #define MII_BCM54XX_EXP_AADJ1CH0_SWSEL_THPF 0x0100 221 #define MII_BCM54XX_EXP_AADJ1CH3 0x601f 222 #define MII_BCM54XX_EXP_AADJ1CH3_ADCCKADJ 0x0002 223 #define MII_BCM54XX_EXP_EXP08 0x0F08 224 #define MII_BCM54XX_EXP_EXP08_RJCT_2MHZ 0x0001 225 #define MII_BCM54XX_EXP_EXP08_EARLY_DAC_WAKE 0x0200 226 #define MII_BCM54XX_EXP_EXP75 0x0f75 227 #define MII_BCM54XX_EXP_EXP75_VDACCTRL 0x003c 228 #define MII_BCM54XX_EXP_EXP75_CM_OSC 0x0001 229 #define MII_BCM54XX_EXP_EXP96 0x0f96 230 #define MII_BCM54XX_EXP_EXP96_MYST 0x0010 231 #define MII_BCM54XX_EXP_EXP97 0x0f97 232 #define MII_BCM54XX_EXP_EXP97_MYST 0x0c0c 233 234 /* 235 * BCM5482: Secondary SerDes registers 236 */ 237 #define BCM5482_SSD_1000BX_CTL 0x00 /* 1000BASE-X Control */ 238 #define BCM5482_SSD_1000BX_CTL_PWRDOWN 0x0800 /* Power-down SSD */ 239 #define BCM5482_SSD_SGMII_SLAVE 0x15 /* SGMII Slave Register */ 240 #define BCM5482_SSD_SGMII_SLAVE_EN 0x0002 /* Slave mode enable */ 241 #define BCM5482_SSD_SGMII_SLAVE_AD 0x0001 /* Slave auto-detection */ 242 243 /* BCM54810 Registers */ 244 #define BCM54810_EXP_BROADREACH_LRE_MISC_CTL (MII_BCM54XX_EXP_SEL_ER + 0x90) 245 #define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN (1 << 0) 246 #define BCM54810_SHD_CLK_CTL 0x3 247 #define BCM54810_SHD_CLK_CTL_GTXCLK_EN (1 << 9) 248 249 /* BCM54612E Registers */ 250 #define BCM54612E_EXP_SPARE0 (MII_BCM54XX_EXP_SEL_ETC + 0x34) 251 #define BCM54612E_LED4_CLK125OUT_EN (1 << 1) 252 253 /*****************************************************************************/ 254 /* Fast Ethernet Transceiver definitions. */ 255 /*****************************************************************************/ 256 257 #define MII_BRCM_FET_INTREG 0x1a /* Interrupt register */ 258 #define MII_BRCM_FET_IR_MASK 0x0100 /* Mask all interrupts */ 259 #define MII_BRCM_FET_IR_LINK_EN 0x0200 /* Link status change enable */ 260 #define MII_BRCM_FET_IR_SPEED_EN 0x0400 /* Link speed change enable */ 261 #define MII_BRCM_FET_IR_DUPLEX_EN 0x0800 /* Duplex mode change enable */ 262 #define MII_BRCM_FET_IR_ENABLE 0x4000 /* Interrupt enable */ 263 264 #define MII_BRCM_FET_BRCMTEST 0x1f /* Brcm test register */ 265 #define MII_BRCM_FET_BT_SRE 0x0080 /* Shadow register enable */ 266 267 268 /*** Shadow register definitions ***/ 269 270 #define MII_BRCM_FET_SHDW_MISCCTRL 0x10 /* Shadow misc ctrl */ 271 #define MII_BRCM_FET_SHDW_MC_FAME 0x4000 /* Force Auto MDIX enable */ 272 273 #define MII_BRCM_FET_SHDW_AUXMODE4 0x1a /* Auxiliary mode 4 */ 274 #define MII_BRCM_FET_SHDW_AM4_LED_MASK 0x0003 275 #define MII_BRCM_FET_SHDW_AM4_LED_MODE1 0x0001 276 277 #define MII_BRCM_FET_SHDW_AUXSTAT2 0x1b /* Auxiliary status 2 */ 278 #define MII_BRCM_FET_SHDW_AS2_APDE 0x0020 /* Auto power down enable */ 279 280 #define BRCM_CL45VEN_EEE_CONTROL 0x803d 281 #define LPI_FEATURE_EN 0x8000 282 #define LPI_FEATURE_EN_DIG1000X 0x4000 283 284 /* Core register definitions*/ 285 #define MII_BRCM_CORE_BASE12 0x12 286 #define MII_BRCM_CORE_BASE13 0x13 287 #define MII_BRCM_CORE_BASE14 0x14 288 #define MII_BRCM_CORE_BASE1E 0x1E 289 #define MII_BRCM_CORE_EXPB0 0xB0 290 #define MII_BRCM_CORE_EXPB1 0xB1 291 292 #endif /* _LINUX_BRCMPHY_H */ 293