1 /* 2 * Copyright 2016 IBM Corporation 3 * 4 * Joel Stanley <joel@jms.id.au> 5 * 6 * This program is free software; you can redistribute it and/or 7 * modify it under the terms of the GNU General Public License 8 * as published by the Free Software Foundation; either version 9 * 2 of the License, or (at your option) any later version. 10 */ 11 12 #include <linux/delay.h> 13 #include <linux/io.h> 14 #include <linux/kernel.h> 15 #include <linux/module.h> 16 #include <linux/of.h> 17 #include <linux/platform_device.h> 18 #include <linux/watchdog.h> 19 20 struct aspeed_wdt { 21 struct watchdog_device wdd; 22 void __iomem *base; 23 u32 ctrl; 24 }; 25 26 struct aspeed_wdt_config { 27 u32 ext_pulse_width_mask; 28 }; 29 30 static const struct aspeed_wdt_config ast2400_config = { 31 .ext_pulse_width_mask = 0xff, 32 }; 33 34 static const struct aspeed_wdt_config ast2500_config = { 35 .ext_pulse_width_mask = 0xfffff, 36 }; 37 38 static const struct of_device_id aspeed_wdt_of_table[] = { 39 { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config }, 40 { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config }, 41 { }, 42 }; 43 MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table); 44 45 #define WDT_STATUS 0x00 46 #define WDT_RELOAD_VALUE 0x04 47 #define WDT_RESTART 0x08 48 #define WDT_CTRL 0x0C 49 #define WDT_CTRL_BOOT_SECONDARY BIT(7) 50 #define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) 51 #define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) 52 #define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) 53 #define WDT_CTRL_1MHZ_CLK BIT(4) 54 #define WDT_CTRL_WDT_EXT BIT(3) 55 #define WDT_CTRL_WDT_INTR BIT(2) 56 #define WDT_CTRL_RESET_SYSTEM BIT(1) 57 #define WDT_CTRL_ENABLE BIT(0) 58 #define WDT_TIMEOUT_STATUS 0x10 59 #define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) 60 61 /* 62 * WDT_RESET_WIDTH controls the characteristics of the external pulse (if 63 * enabled), specifically: 64 * 65 * * Pulse duration 66 * * Drive mode: push-pull vs open-drain 67 * * Polarity: Active high or active low 68 * 69 * Pulse duration configuration is available on both the AST2400 and AST2500, 70 * though the field changes between SoCs: 71 * 72 * AST2400: Bits 7:0 73 * AST2500: Bits 19:0 74 * 75 * This difference is captured in struct aspeed_wdt_config. 76 * 77 * The AST2500 exposes the drive mode and polarity options, but not in a 78 * regular fashion. For read purposes, bit 31 represents active high or low, 79 * and bit 30 represents push-pull or open-drain. With respect to write, magic 80 * values need to be written to the top byte to change the state of the drive 81 * mode and polarity bits. Any other value written to the top byte has no 82 * effect on the state of the drive mode or polarity bits. However, the pulse 83 * width value must be preserved (as desired) if written. 84 */ 85 #define WDT_RESET_WIDTH 0x18 86 #define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31) 87 #define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24) 88 #define WDT_ACTIVE_LOW_MAGIC (0x5A << 24) 89 #define WDT_RESET_WIDTH_PUSH_PULL BIT(30) 90 #define WDT_PUSH_PULL_MAGIC (0xA8 << 24) 91 #define WDT_OPEN_DRAIN_MAGIC (0x8A << 24) 92 93 #define WDT_RESTART_MAGIC 0x4755 94 95 /* 32 bits at 1MHz, in milliseconds */ 96 #define WDT_MAX_TIMEOUT_MS 4294967 97 #define WDT_DEFAULT_TIMEOUT 30 98 #define WDT_RATE_1MHZ 1000000 99 100 static struct aspeed_wdt *to_aspeed_wdt(struct watchdog_device *wdd) 101 { 102 return container_of(wdd, struct aspeed_wdt, wdd); 103 } 104 105 static void aspeed_wdt_enable(struct aspeed_wdt *wdt, int count) 106 { 107 wdt->ctrl |= WDT_CTRL_ENABLE; 108 109 writel(0, wdt->base + WDT_CTRL); 110 writel(count, wdt->base + WDT_RELOAD_VALUE); 111 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); 112 writel(wdt->ctrl, wdt->base + WDT_CTRL); 113 } 114 115 static int aspeed_wdt_start(struct watchdog_device *wdd) 116 { 117 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 118 119 aspeed_wdt_enable(wdt, wdd->timeout * WDT_RATE_1MHZ); 120 121 return 0; 122 } 123 124 static int aspeed_wdt_stop(struct watchdog_device *wdd) 125 { 126 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 127 128 wdt->ctrl &= ~WDT_CTRL_ENABLE; 129 writel(wdt->ctrl, wdt->base + WDT_CTRL); 130 131 return 0; 132 } 133 134 static int aspeed_wdt_ping(struct watchdog_device *wdd) 135 { 136 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 137 138 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); 139 140 return 0; 141 } 142 143 static int aspeed_wdt_set_timeout(struct watchdog_device *wdd, 144 unsigned int timeout) 145 { 146 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 147 u32 actual; 148 149 wdd->timeout = timeout; 150 151 actual = min(timeout, wdd->max_hw_heartbeat_ms * 1000); 152 153 writel(actual * WDT_RATE_1MHZ, wdt->base + WDT_RELOAD_VALUE); 154 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); 155 156 return 0; 157 } 158 159 static int aspeed_wdt_restart(struct watchdog_device *wdd, 160 unsigned long action, void *data) 161 { 162 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 163 164 wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY; 165 aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000); 166 167 mdelay(1000); 168 169 return 0; 170 } 171 172 static const struct watchdog_ops aspeed_wdt_ops = { 173 .start = aspeed_wdt_start, 174 .stop = aspeed_wdt_stop, 175 .ping = aspeed_wdt_ping, 176 .set_timeout = aspeed_wdt_set_timeout, 177 .restart = aspeed_wdt_restart, 178 .owner = THIS_MODULE, 179 }; 180 181 static const struct watchdog_info aspeed_wdt_info = { 182 .options = WDIOF_KEEPALIVEPING 183 | WDIOF_MAGICCLOSE 184 | WDIOF_SETTIMEOUT, 185 .identity = KBUILD_MODNAME, 186 }; 187 188 static int aspeed_wdt_probe(struct platform_device *pdev) 189 { 190 const struct aspeed_wdt_config *config; 191 const struct of_device_id *ofdid; 192 struct aspeed_wdt *wdt; 193 struct resource *res; 194 struct device_node *np; 195 const char *reset_type; 196 u32 duration; 197 u32 status; 198 int ret; 199 200 wdt = devm_kzalloc(&pdev->dev, sizeof(*wdt), GFP_KERNEL); 201 if (!wdt) 202 return -ENOMEM; 203 204 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 205 wdt->base = devm_ioremap_resource(&pdev->dev, res); 206 if (IS_ERR(wdt->base)) 207 return PTR_ERR(wdt->base); 208 209 /* 210 * The ast2400 wdt can run at PCLK, or 1MHz. The ast2500 only 211 * runs at 1MHz. We chose to always run at 1MHz, as there's no 212 * good reason to have a faster watchdog counter. 213 */ 214 wdt->wdd.info = &aspeed_wdt_info; 215 wdt->wdd.ops = &aspeed_wdt_ops; 216 wdt->wdd.max_hw_heartbeat_ms = WDT_MAX_TIMEOUT_MS; 217 wdt->wdd.parent = &pdev->dev; 218 219 wdt->wdd.timeout = WDT_DEFAULT_TIMEOUT; 220 watchdog_init_timeout(&wdt->wdd, 0, &pdev->dev); 221 222 np = pdev->dev.of_node; 223 224 ofdid = of_match_node(aspeed_wdt_of_table, np); 225 if (!ofdid) 226 return -EINVAL; 227 config = ofdid->data; 228 229 wdt->ctrl = WDT_CTRL_1MHZ_CLK; 230 231 /* 232 * Control reset on a per-device basis to ensure the 233 * host is not affected by a BMC reboot 234 */ 235 ret = of_property_read_string(np, "aspeed,reset-type", &reset_type); 236 if (ret) { 237 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | WDT_CTRL_RESET_SYSTEM; 238 } else { 239 if (!strcmp(reset_type, "cpu")) 240 wdt->ctrl |= WDT_CTRL_RESET_MODE_ARM_CPU | 241 WDT_CTRL_RESET_SYSTEM; 242 else if (!strcmp(reset_type, "soc")) 243 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | 244 WDT_CTRL_RESET_SYSTEM; 245 else if (!strcmp(reset_type, "system")) 246 wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP | 247 WDT_CTRL_RESET_SYSTEM; 248 else if (strcmp(reset_type, "none")) 249 return -EINVAL; 250 } 251 if (of_property_read_bool(np, "aspeed,external-signal")) 252 wdt->ctrl |= WDT_CTRL_WDT_EXT; 253 if (of_property_read_bool(np, "aspeed,alt-boot")) 254 wdt->ctrl |= WDT_CTRL_BOOT_SECONDARY; 255 256 if (readl(wdt->base + WDT_CTRL) & WDT_CTRL_ENABLE) { 257 /* 258 * The watchdog is running, but invoke aspeed_wdt_start() to 259 * write wdt->ctrl to WDT_CTRL to ensure the watchdog's 260 * configuration conforms to the driver's expectations. 261 * Primarily, ensure we're using the 1MHz clock source. 262 */ 263 aspeed_wdt_start(&wdt->wdd); 264 set_bit(WDOG_HW_RUNNING, &wdt->wdd.status); 265 } 266 267 if (of_device_is_compatible(np, "aspeed,ast2500-wdt")) { 268 u32 reg = readl(wdt->base + WDT_RESET_WIDTH); 269 270 reg &= config->ext_pulse_width_mask; 271 if (of_property_read_bool(np, "aspeed,ext-push-pull")) 272 reg |= WDT_PUSH_PULL_MAGIC; 273 else 274 reg |= WDT_OPEN_DRAIN_MAGIC; 275 276 writel(reg, wdt->base + WDT_RESET_WIDTH); 277 278 reg &= config->ext_pulse_width_mask; 279 if (of_property_read_bool(np, "aspeed,ext-active-high")) 280 reg |= WDT_ACTIVE_HIGH_MAGIC; 281 else 282 reg |= WDT_ACTIVE_LOW_MAGIC; 283 284 writel(reg, wdt->base + WDT_RESET_WIDTH); 285 } 286 287 if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) { 288 u32 max_duration = config->ext_pulse_width_mask + 1; 289 290 if (duration == 0 || duration > max_duration) { 291 dev_err(&pdev->dev, "Invalid pulse duration: %uus\n", 292 duration); 293 duration = max(1U, min(max_duration, duration)); 294 dev_info(&pdev->dev, "Pulse duration set to %uus\n", 295 duration); 296 } 297 298 /* 299 * The watchdog is always configured with a 1MHz source, so 300 * there is no need to scale the microsecond value. However we 301 * need to offset it - from the datasheet: 302 * 303 * "This register decides the asserting duration of wdt_ext and 304 * wdt_rstarm signal. The default value is 0xFF. It means the 305 * default asserting duration of wdt_ext and wdt_rstarm is 306 * 256us." 307 * 308 * This implies a value of 0 gives a 1us pulse. 309 */ 310 writel(duration - 1, wdt->base + WDT_RESET_WIDTH); 311 } 312 313 status = readl(wdt->base + WDT_TIMEOUT_STATUS); 314 if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) 315 wdt->wdd.bootstatus = WDIOF_CARDRESET; 316 317 ret = devm_watchdog_register_device(&pdev->dev, &wdt->wdd); 318 if (ret) { 319 dev_err(&pdev->dev, "failed to register\n"); 320 return ret; 321 } 322 323 return 0; 324 } 325 326 static struct platform_driver aspeed_watchdog_driver = { 327 .probe = aspeed_wdt_probe, 328 .driver = { 329 .name = KBUILD_MODNAME, 330 .of_match_table = of_match_ptr(aspeed_wdt_of_table), 331 }, 332 }; 333 334 static int __init aspeed_wdt_init(void) 335 { 336 return platform_driver_register(&aspeed_watchdog_driver); 337 } 338 arch_initcall(aspeed_wdt_init); 339 340 static void __exit aspeed_wdt_exit(void) 341 { 342 platform_driver_unregister(&aspeed_watchdog_driver); 343 } 344 module_exit(aspeed_wdt_exit); 345 346 MODULE_DESCRIPTION("Aspeed Watchdog Driver"); 347 MODULE_LICENSE("GPL"); 348