1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Copyright 2016 IBM Corporation 4 * 5 * Joel Stanley <joel@jms.id.au> 6 */ 7 8 #include <linux/delay.h> 9 #include <linux/io.h> 10 #include <linux/kernel.h> 11 #include <linux/module.h> 12 #include <linux/of.h> 13 #include <linux/platform_device.h> 14 #include <linux/watchdog.h> 15 16 struct aspeed_wdt { 17 struct watchdog_device wdd; 18 void __iomem *base; 19 u32 ctrl; 20 }; 21 22 struct aspeed_wdt_config { 23 u32 ext_pulse_width_mask; 24 }; 25 26 static const struct aspeed_wdt_config ast2400_config = { 27 .ext_pulse_width_mask = 0xff, 28 }; 29 30 static const struct aspeed_wdt_config ast2500_config = { 31 .ext_pulse_width_mask = 0xfffff, 32 }; 33 34 static const struct of_device_id aspeed_wdt_of_table[] = { 35 { .compatible = "aspeed,ast2400-wdt", .data = &ast2400_config }, 36 { .compatible = "aspeed,ast2500-wdt", .data = &ast2500_config }, 37 { .compatible = "aspeed,ast2600-wdt", .data = &ast2500_config }, 38 { }, 39 }; 40 MODULE_DEVICE_TABLE(of, aspeed_wdt_of_table); 41 42 #define WDT_STATUS 0x00 43 #define WDT_RELOAD_VALUE 0x04 44 #define WDT_RESTART 0x08 45 #define WDT_CTRL 0x0C 46 #define WDT_CTRL_BOOT_SECONDARY BIT(7) 47 #define WDT_CTRL_RESET_MODE_SOC (0x00 << 5) 48 #define WDT_CTRL_RESET_MODE_FULL_CHIP (0x01 << 5) 49 #define WDT_CTRL_RESET_MODE_ARM_CPU (0x10 << 5) 50 #define WDT_CTRL_1MHZ_CLK BIT(4) 51 #define WDT_CTRL_WDT_EXT BIT(3) 52 #define WDT_CTRL_WDT_INTR BIT(2) 53 #define WDT_CTRL_RESET_SYSTEM BIT(1) 54 #define WDT_CTRL_ENABLE BIT(0) 55 #define WDT_TIMEOUT_STATUS 0x10 56 #define WDT_TIMEOUT_STATUS_BOOT_SECONDARY BIT(1) 57 #define WDT_CLEAR_TIMEOUT_STATUS 0x14 58 #define WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION BIT(0) 59 60 /* 61 * WDT_RESET_WIDTH controls the characteristics of the external pulse (if 62 * enabled), specifically: 63 * 64 * * Pulse duration 65 * * Drive mode: push-pull vs open-drain 66 * * Polarity: Active high or active low 67 * 68 * Pulse duration configuration is available on both the AST2400 and AST2500, 69 * though the field changes between SoCs: 70 * 71 * AST2400: Bits 7:0 72 * AST2500: Bits 19:0 73 * 74 * This difference is captured in struct aspeed_wdt_config. 75 * 76 * The AST2500 exposes the drive mode and polarity options, but not in a 77 * regular fashion. For read purposes, bit 31 represents active high or low, 78 * and bit 30 represents push-pull or open-drain. With respect to write, magic 79 * values need to be written to the top byte to change the state of the drive 80 * mode and polarity bits. Any other value written to the top byte has no 81 * effect on the state of the drive mode or polarity bits. However, the pulse 82 * width value must be preserved (as desired) if written. 83 */ 84 #define WDT_RESET_WIDTH 0x18 85 #define WDT_RESET_WIDTH_ACTIVE_HIGH BIT(31) 86 #define WDT_ACTIVE_HIGH_MAGIC (0xA5 << 24) 87 #define WDT_ACTIVE_LOW_MAGIC (0x5A << 24) 88 #define WDT_RESET_WIDTH_PUSH_PULL BIT(30) 89 #define WDT_PUSH_PULL_MAGIC (0xA8 << 24) 90 #define WDT_OPEN_DRAIN_MAGIC (0x8A << 24) 91 92 #define WDT_RESTART_MAGIC 0x4755 93 94 /* 32 bits at 1MHz, in milliseconds */ 95 #define WDT_MAX_TIMEOUT_MS 4294967 96 #define WDT_DEFAULT_TIMEOUT 30 97 #define WDT_RATE_1MHZ 1000000 98 99 static struct aspeed_wdt *to_aspeed_wdt(struct watchdog_device *wdd) 100 { 101 return container_of(wdd, struct aspeed_wdt, wdd); 102 } 103 104 static void aspeed_wdt_enable(struct aspeed_wdt *wdt, int count) 105 { 106 wdt->ctrl |= WDT_CTRL_ENABLE; 107 108 writel(0, wdt->base + WDT_CTRL); 109 writel(count, wdt->base + WDT_RELOAD_VALUE); 110 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); 111 writel(wdt->ctrl, wdt->base + WDT_CTRL); 112 } 113 114 static int aspeed_wdt_start(struct watchdog_device *wdd) 115 { 116 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 117 118 aspeed_wdt_enable(wdt, wdd->timeout * WDT_RATE_1MHZ); 119 120 return 0; 121 } 122 123 static int aspeed_wdt_stop(struct watchdog_device *wdd) 124 { 125 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 126 127 wdt->ctrl &= ~WDT_CTRL_ENABLE; 128 writel(wdt->ctrl, wdt->base + WDT_CTRL); 129 130 return 0; 131 } 132 133 static int aspeed_wdt_ping(struct watchdog_device *wdd) 134 { 135 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 136 137 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); 138 139 return 0; 140 } 141 142 static int aspeed_wdt_set_timeout(struct watchdog_device *wdd, 143 unsigned int timeout) 144 { 145 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 146 u32 actual; 147 148 wdd->timeout = timeout; 149 150 actual = min(timeout, wdd->max_hw_heartbeat_ms * 1000); 151 152 writel(actual * WDT_RATE_1MHZ, wdt->base + WDT_RELOAD_VALUE); 153 writel(WDT_RESTART_MAGIC, wdt->base + WDT_RESTART); 154 155 return 0; 156 } 157 158 static int aspeed_wdt_restart(struct watchdog_device *wdd, 159 unsigned long action, void *data) 160 { 161 struct aspeed_wdt *wdt = to_aspeed_wdt(wdd); 162 163 wdt->ctrl &= ~WDT_CTRL_BOOT_SECONDARY; 164 aspeed_wdt_enable(wdt, 128 * WDT_RATE_1MHZ / 1000); 165 166 mdelay(1000); 167 168 return 0; 169 } 170 171 /* access_cs0 shows if cs0 is accessible, hence the reverted bit */ 172 static ssize_t access_cs0_show(struct device *dev, 173 struct device_attribute *attr, char *buf) 174 { 175 struct aspeed_wdt *wdt = dev_get_drvdata(dev); 176 u32 status = readl(wdt->base + WDT_TIMEOUT_STATUS); 177 178 return sprintf(buf, "%u\n", 179 !(status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY)); 180 } 181 182 static ssize_t access_cs0_store(struct device *dev, 183 struct device_attribute *attr, const char *buf, 184 size_t size) 185 { 186 struct aspeed_wdt *wdt = dev_get_drvdata(dev); 187 unsigned long val; 188 189 if (kstrtoul(buf, 10, &val)) 190 return -EINVAL; 191 192 if (val) 193 writel(WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION, 194 wdt->base + WDT_CLEAR_TIMEOUT_STATUS); 195 196 return size; 197 } 198 199 /* 200 * This attribute exists only if the system has booted from the alternate 201 * flash with 'alt-boot' option. 202 * 203 * At alternate flash the 'access_cs0' sysfs node provides: 204 * ast2400: a way to get access to the primary SPI flash chip at CS0 205 * after booting from the alternate chip at CS1. 206 * ast2500: a way to restore the normal address mapping from 207 * (CS0->CS1, CS1->CS0) to (CS0->CS0, CS1->CS1). 208 * 209 * Clearing the boot code selection and timeout counter also resets to the 210 * initial state the chip select line mapping. When the SoC is in normal 211 * mapping state (i.e. booted from CS0), clearing those bits does nothing for 212 * both versions of the SoC. For alternate boot mode (booted from CS1 due to 213 * wdt2 expiration) the behavior differs as described above. 214 * 215 * This option can be used with wdt2 (watchdog1) only. 216 */ 217 static DEVICE_ATTR_RW(access_cs0); 218 219 static struct attribute *bswitch_attrs[] = { 220 &dev_attr_access_cs0.attr, 221 NULL 222 }; 223 ATTRIBUTE_GROUPS(bswitch); 224 225 static const struct watchdog_ops aspeed_wdt_ops = { 226 .start = aspeed_wdt_start, 227 .stop = aspeed_wdt_stop, 228 .ping = aspeed_wdt_ping, 229 .set_timeout = aspeed_wdt_set_timeout, 230 .restart = aspeed_wdt_restart, 231 .owner = THIS_MODULE, 232 }; 233 234 static const struct watchdog_info aspeed_wdt_info = { 235 .options = WDIOF_KEEPALIVEPING 236 | WDIOF_MAGICCLOSE 237 | WDIOF_SETTIMEOUT, 238 .identity = KBUILD_MODNAME, 239 }; 240 241 static int aspeed_wdt_probe(struct platform_device *pdev) 242 { 243 struct device *dev = &pdev->dev; 244 const struct aspeed_wdt_config *config; 245 const struct of_device_id *ofdid; 246 struct aspeed_wdt *wdt; 247 struct device_node *np; 248 const char *reset_type; 249 u32 duration; 250 u32 status; 251 int ret; 252 253 wdt = devm_kzalloc(dev, sizeof(*wdt), GFP_KERNEL); 254 if (!wdt) 255 return -ENOMEM; 256 257 wdt->base = devm_platform_ioremap_resource(pdev, 0); 258 if (IS_ERR(wdt->base)) 259 return PTR_ERR(wdt->base); 260 261 wdt->wdd.info = &aspeed_wdt_info; 262 wdt->wdd.ops = &aspeed_wdt_ops; 263 wdt->wdd.max_hw_heartbeat_ms = WDT_MAX_TIMEOUT_MS; 264 wdt->wdd.parent = dev; 265 266 wdt->wdd.timeout = WDT_DEFAULT_TIMEOUT; 267 watchdog_init_timeout(&wdt->wdd, 0, dev); 268 269 np = dev->of_node; 270 271 ofdid = of_match_node(aspeed_wdt_of_table, np); 272 if (!ofdid) 273 return -EINVAL; 274 config = ofdid->data; 275 276 /* 277 * On clock rates: 278 * - ast2400 wdt can run at PCLK, or 1MHz 279 * - ast2500 only runs at 1MHz, hard coding bit 4 to 1 280 * - ast2600 always runs at 1MHz 281 * 282 * Set the ast2400 to run at 1MHz as it simplifies the driver. 283 */ 284 if (of_device_is_compatible(np, "aspeed,ast2400-wdt")) 285 wdt->ctrl = WDT_CTRL_1MHZ_CLK; 286 287 /* 288 * Control reset on a per-device basis to ensure the 289 * host is not affected by a BMC reboot 290 */ 291 ret = of_property_read_string(np, "aspeed,reset-type", &reset_type); 292 if (ret) { 293 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | WDT_CTRL_RESET_SYSTEM; 294 } else { 295 if (!strcmp(reset_type, "cpu")) 296 wdt->ctrl |= WDT_CTRL_RESET_MODE_ARM_CPU | 297 WDT_CTRL_RESET_SYSTEM; 298 else if (!strcmp(reset_type, "soc")) 299 wdt->ctrl |= WDT_CTRL_RESET_MODE_SOC | 300 WDT_CTRL_RESET_SYSTEM; 301 else if (!strcmp(reset_type, "system")) 302 wdt->ctrl |= WDT_CTRL_RESET_MODE_FULL_CHIP | 303 WDT_CTRL_RESET_SYSTEM; 304 else if (strcmp(reset_type, "none")) 305 return -EINVAL; 306 } 307 if (of_property_read_bool(np, "aspeed,external-signal")) 308 wdt->ctrl |= WDT_CTRL_WDT_EXT; 309 if (of_property_read_bool(np, "aspeed,alt-boot")) 310 wdt->ctrl |= WDT_CTRL_BOOT_SECONDARY; 311 312 if (readl(wdt->base + WDT_CTRL) & WDT_CTRL_ENABLE) { 313 /* 314 * The watchdog is running, but invoke aspeed_wdt_start() to 315 * write wdt->ctrl to WDT_CTRL to ensure the watchdog's 316 * configuration conforms to the driver's expectations. 317 * Primarily, ensure we're using the 1MHz clock source. 318 */ 319 aspeed_wdt_start(&wdt->wdd); 320 set_bit(WDOG_HW_RUNNING, &wdt->wdd.status); 321 } 322 323 if ((of_device_is_compatible(np, "aspeed,ast2500-wdt")) || 324 (of_device_is_compatible(np, "aspeed,ast2600-wdt"))) { 325 u32 reg = readl(wdt->base + WDT_RESET_WIDTH); 326 327 reg &= config->ext_pulse_width_mask; 328 if (of_property_read_bool(np, "aspeed,ext-push-pull")) 329 reg |= WDT_PUSH_PULL_MAGIC; 330 else 331 reg |= WDT_OPEN_DRAIN_MAGIC; 332 333 writel(reg, wdt->base + WDT_RESET_WIDTH); 334 335 reg &= config->ext_pulse_width_mask; 336 if (of_property_read_bool(np, "aspeed,ext-active-high")) 337 reg |= WDT_ACTIVE_HIGH_MAGIC; 338 else 339 reg |= WDT_ACTIVE_LOW_MAGIC; 340 341 writel(reg, wdt->base + WDT_RESET_WIDTH); 342 } 343 344 if (!of_property_read_u32(np, "aspeed,ext-pulse-duration", &duration)) { 345 u32 max_duration = config->ext_pulse_width_mask + 1; 346 347 if (duration == 0 || duration > max_duration) { 348 dev_err(dev, "Invalid pulse duration: %uus\n", 349 duration); 350 duration = max(1U, min(max_duration, duration)); 351 dev_info(dev, "Pulse duration set to %uus\n", 352 duration); 353 } 354 355 /* 356 * The watchdog is always configured with a 1MHz source, so 357 * there is no need to scale the microsecond value. However we 358 * need to offset it - from the datasheet: 359 * 360 * "This register decides the asserting duration of wdt_ext and 361 * wdt_rstarm signal. The default value is 0xFF. It means the 362 * default asserting duration of wdt_ext and wdt_rstarm is 363 * 256us." 364 * 365 * This implies a value of 0 gives a 1us pulse. 366 */ 367 writel(duration - 1, wdt->base + WDT_RESET_WIDTH); 368 } 369 370 status = readl(wdt->base + WDT_TIMEOUT_STATUS); 371 if (status & WDT_TIMEOUT_STATUS_BOOT_SECONDARY) { 372 wdt->wdd.bootstatus = WDIOF_CARDRESET; 373 374 if (of_device_is_compatible(np, "aspeed,ast2400-wdt") || 375 of_device_is_compatible(np, "aspeed,ast2500-wdt")) 376 wdt->wdd.groups = bswitch_groups; 377 } 378 379 dev_set_drvdata(dev, wdt); 380 381 return devm_watchdog_register_device(dev, &wdt->wdd); 382 } 383 384 static struct platform_driver aspeed_watchdog_driver = { 385 .probe = aspeed_wdt_probe, 386 .driver = { 387 .name = KBUILD_MODNAME, 388 .of_match_table = of_match_ptr(aspeed_wdt_of_table), 389 }, 390 }; 391 392 static int __init aspeed_wdt_init(void) 393 { 394 return platform_driver_register(&aspeed_watchdog_driver); 395 } 396 arch_initcall(aspeed_wdt_init); 397 398 static void __exit aspeed_wdt_exit(void) 399 { 400 platform_driver_unregister(&aspeed_watchdog_driver); 401 } 402 module_exit(aspeed_wdt_exit); 403 404 MODULE_DESCRIPTION("Aspeed Watchdog Driver"); 405 MODULE_LICENSE("GPL"); 406