1# 2# 1-wire slaves configuration 3# 4 5menu "1-wire Slaves" 6 7config W1_SLAVE_THERM 8 tristate "Thermal family implementation" 9 help 10 Say Y here if you want to connect 1-wire thermal sensors to your 11 wire. 12 13config W1_SLAVE_SMEM 14 tristate "Simple 64bit memory family implementation" 15 help 16 Say Y here if you want to connect 1-wire 17 simple 64bit memory rom(ds2401/ds2411/ds1990*) to your wire. 18 19config W1_SLAVE_DS2408 20 tristate "8-Channel Addressable Switch (IO Expander) 0x29 family support (DS2408)" 21 help 22 Say Y here if you want to use a 1-wire 23 24 DS2408 8-Channel Addressable Switch device support 25 26config W1_SLAVE_DS2423 27 tristate "Counter 1-wire device (DS2423)" 28 select CRC16 29 help 30 If you enable this you can read the counter values available 31 in the DS2423 chipset from the w1_slave file under the 32 sys file system. 33 34 Say Y here if you want to use a 1-wire 35 counter family device (DS2423). 36 37config W1_SLAVE_DS2431 38 tristate "1kb EEPROM family support (DS2431)" 39 help 40 Say Y here if you want to use a 1-wire 41 1kb EEPROM family device (DS2431) 42 43config W1_SLAVE_DS2433 44 tristate "4kb EEPROM family support (DS2433)" 45 help 46 Say Y here if you want to use a 1-wire 47 4kb EEPROM family device (DS2433). 48 49config W1_SLAVE_DS2433_CRC 50 bool "Protect DS2433 data with a CRC16" 51 depends on W1_SLAVE_DS2433 52 select CRC16 53 help 54 Say Y here to protect DS2433 data with a CRC16. 55 Each block has 30 bytes of data and a two byte CRC16. 56 Full block writes are only allowed if the CRC is valid. 57 58config W1_SLAVE_DS2760 59 tristate "Dallas 2760 battery monitor chip (HP iPAQ & others)" 60 depends on W1 61 help 62 If you enable this you will have the DS2760 battery monitor 63 chip support. 64 65 The battery monitor chip is used in many batteries/devices 66 as the one who is responsible for charging/discharging/monitoring 67 Li+ batteries. 68 69 If you are unsure, say N. 70 71config W1_SLAVE_DS2780 72 tristate "Dallas 2780 battery monitor chip" 73 depends on W1 74 help 75 If you enable this you will have the DS2780 battery monitor 76 chip support. 77 78 The battery monitor chip is used in many batteries/devices 79 as the one who is responsible for charging/discharging/monitoring 80 Li+ batteries. 81 82 If you are unsure, say N. 83 84config W1_SLAVE_DS2781 85 tristate "Dallas 2781 battery monitor chip" 86 depends on W1 87 help 88 If you enable this you will have the DS2781 battery monitor 89 chip support. 90 91 The battery monitor chip is used in many batteries/devices 92 as the one who is responsible for charging/discharging/monitoring 93 Li+ batteries. 94 95 If you are unsure, say N. 96 97config W1_SLAVE_BQ27000 98 tristate "BQ27000 slave support" 99 depends on W1 100 help 101 Say Y here if you want to use a hdq 102 bq27000 slave support. 103 104endmenu 105