1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * ds2482.c - provides i2c to w1-master bridge(s) 4 * Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com> 5 * 6 * The DS2482 is a sensor chip made by Dallas Semiconductor (Maxim). 7 * It is a I2C to 1-wire bridge. 8 * There are two variations: -100 and -800, which have 1 or 8 1-wire ports. 9 * The complete datasheet can be obtained from MAXIM's website at: 10 * http://www.maxim-ic.com/quick_view2.cfm/qv_pk/4382 11 */ 12 13 #include <linux/module.h> 14 #include <linux/init.h> 15 #include <linux/slab.h> 16 #include <linux/i2c.h> 17 #include <linux/delay.h> 18 #include <asm/delay.h> 19 20 #include <linux/w1.h> 21 22 /* 23 * Allow the active pullup to be disabled, default is enabled. 24 * 25 * Note from the DS2482 datasheet: 26 * The APU bit controls whether an active pullup (controlled slew-rate 27 * transistor) or a passive pullup (Rwpu resistor) will be used to drive 28 * a 1-Wire line from low to high. When APU = 0, active pullup is disabled 29 * (resistor mode). Active Pullup should always be selected unless there is 30 * only a single slave on the 1-Wire line. 31 */ 32 static int ds2482_active_pullup = 1; 33 module_param_named(active_pullup, ds2482_active_pullup, int, 0644); 34 MODULE_PARM_DESC(active_pullup, "Active pullup (apply to all buses): " \ 35 "0-disable, 1-enable (default)"); 36 37 /* extra configurations - e.g. 1WS */ 38 static int extra_config; 39 module_param(extra_config, int, S_IRUGO | S_IWUSR); 40 MODULE_PARM_DESC(extra_config, "Extra Configuration settings 1=APU,2=PPM,3=SPU,8=1WS"); 41 42 /* 43 * The DS2482 registers - there are 3 registers that are addressed by a read 44 * pointer. The read pointer is set by the last command executed. 45 * 46 * To read the data, issue a register read for any address 47 */ 48 #define DS2482_CMD_RESET 0xF0 /* No param */ 49 #define DS2482_CMD_SET_READ_PTR 0xE1 /* Param: DS2482_PTR_CODE_xxx */ 50 #define DS2482_CMD_CHANNEL_SELECT 0xC3 /* Param: Channel byte - DS2482-800 only */ 51 #define DS2482_CMD_WRITE_CONFIG 0xD2 /* Param: Config byte */ 52 #define DS2482_CMD_1WIRE_RESET 0xB4 /* Param: None */ 53 #define DS2482_CMD_1WIRE_SINGLE_BIT 0x87 /* Param: Bit byte (bit7) */ 54 #define DS2482_CMD_1WIRE_WRITE_BYTE 0xA5 /* Param: Data byte */ 55 #define DS2482_CMD_1WIRE_READ_BYTE 0x96 /* Param: None */ 56 /* Note to read the byte, Set the ReadPtr to Data then read (any addr) */ 57 #define DS2482_CMD_1WIRE_TRIPLET 0x78 /* Param: Dir byte (bit7) */ 58 59 /* Values for DS2482_CMD_SET_READ_PTR */ 60 #define DS2482_PTR_CODE_STATUS 0xF0 61 #define DS2482_PTR_CODE_DATA 0xE1 62 #define DS2482_PTR_CODE_CHANNEL 0xD2 /* DS2482-800 only */ 63 #define DS2482_PTR_CODE_CONFIG 0xC3 64 65 /* 66 * Configure Register bit definitions 67 * The top 4 bits always read 0. 68 * To write, the top nibble must be the 1's compl. of the low nibble. 69 */ 70 #define DS2482_REG_CFG_1WS 0x08 /* 1-wire speed */ 71 #define DS2482_REG_CFG_SPU 0x04 /* strong pull-up */ 72 #define DS2482_REG_CFG_PPM 0x02 /* presence pulse masking */ 73 #define DS2482_REG_CFG_APU 0x01 /* active pull-up */ 74 75 76 /* 77 * Write and verify codes for the CHANNEL_SELECT command (DS2482-800 only). 78 * To set the channel, write the value at the index of the channel. 79 * Read and compare against the corresponding value to verify the change. 80 */ 81 static const u8 ds2482_chan_wr[8] = 82 { 0xF0, 0xE1, 0xD2, 0xC3, 0xB4, 0xA5, 0x96, 0x87 }; 83 static const u8 ds2482_chan_rd[8] = 84 { 0xB8, 0xB1, 0xAA, 0xA3, 0x9C, 0x95, 0x8E, 0x87 }; 85 86 87 /* 88 * Status Register bit definitions (read only) 89 */ 90 #define DS2482_REG_STS_DIR 0x80 91 #define DS2482_REG_STS_TSB 0x40 92 #define DS2482_REG_STS_SBR 0x20 93 #define DS2482_REG_STS_RST 0x10 94 #define DS2482_REG_STS_LL 0x08 95 #define DS2482_REG_STS_SD 0x04 96 #define DS2482_REG_STS_PPD 0x02 97 #define DS2482_REG_STS_1WB 0x01 98 99 /* 100 * Client data (each client gets its own) 101 */ 102 103 struct ds2482_data; 104 105 struct ds2482_w1_chan { 106 struct ds2482_data *pdev; 107 u8 channel; 108 struct w1_bus_master w1_bm; 109 }; 110 111 struct ds2482_data { 112 struct i2c_client *client; 113 struct mutex access_lock; 114 115 /* 1-wire interface(s) */ 116 int w1_count; /* 1 or 8 */ 117 struct ds2482_w1_chan w1_ch[8]; 118 119 /* per-device values */ 120 u8 channel; 121 u8 read_prt; /* see DS2482_PTR_CODE_xxx */ 122 u8 reg_config; 123 }; 124 125 126 /** 127 * ds2482_calculate_config - Helper to calculate values for configuration register 128 * @conf: the raw config value 129 * Return: the value w/ complements that can be written to register 130 */ 131 static inline u8 ds2482_calculate_config(u8 conf) 132 { 133 conf |= extra_config; 134 135 if (ds2482_active_pullup) 136 conf |= DS2482_REG_CFG_APU; 137 138 return conf | ((~conf & 0x0f) << 4); 139 } 140 141 142 /** 143 * ds2482_select_register - Sets the read pointer. 144 * @pdev: The ds2482 client pointer 145 * @read_ptr: see DS2482_PTR_CODE_xxx above 146 * Return: -1 on failure, 0 on success 147 */ 148 static inline int ds2482_select_register(struct ds2482_data *pdev, u8 read_ptr) 149 { 150 if (pdev->read_prt != read_ptr) { 151 if (i2c_smbus_write_byte_data(pdev->client, 152 DS2482_CMD_SET_READ_PTR, 153 read_ptr) < 0) 154 return -1; 155 156 pdev->read_prt = read_ptr; 157 } 158 return 0; 159 } 160 161 /** 162 * ds2482_send_cmd - Sends a command without a parameter 163 * @pdev: The ds2482 client pointer 164 * @cmd: DS2482_CMD_RESET, 165 * DS2482_CMD_1WIRE_RESET, 166 * DS2482_CMD_1WIRE_READ_BYTE 167 * Return: -1 on failure, 0 on success 168 */ 169 static inline int ds2482_send_cmd(struct ds2482_data *pdev, u8 cmd) 170 { 171 if (i2c_smbus_write_byte(pdev->client, cmd) < 0) 172 return -1; 173 174 pdev->read_prt = DS2482_PTR_CODE_STATUS; 175 return 0; 176 } 177 178 /** 179 * ds2482_send_cmd_data - Sends a command with a parameter 180 * @pdev: The ds2482 client pointer 181 * @cmd: DS2482_CMD_WRITE_CONFIG, 182 * DS2482_CMD_1WIRE_SINGLE_BIT, 183 * DS2482_CMD_1WIRE_WRITE_BYTE, 184 * DS2482_CMD_1WIRE_TRIPLET 185 * @byte: The data to send 186 * Return: -1 on failure, 0 on success 187 */ 188 static inline int ds2482_send_cmd_data(struct ds2482_data *pdev, 189 u8 cmd, u8 byte) 190 { 191 if (i2c_smbus_write_byte_data(pdev->client, cmd, byte) < 0) 192 return -1; 193 194 /* all cmds leave in STATUS, except CONFIG */ 195 pdev->read_prt = (cmd != DS2482_CMD_WRITE_CONFIG) ? 196 DS2482_PTR_CODE_STATUS : DS2482_PTR_CODE_CONFIG; 197 return 0; 198 } 199 200 201 /* 202 * 1-Wire interface code 203 */ 204 205 #define DS2482_WAIT_IDLE_TIMEOUT 100 206 207 /** 208 * ds2482_wait_1wire_idle - Waits until the 1-wire interface is idle (not busy) 209 * 210 * @pdev: Pointer to the device structure 211 * Return: the last value read from status or -1 (failure) 212 */ 213 static int ds2482_wait_1wire_idle(struct ds2482_data *pdev) 214 { 215 int temp = -1; 216 int retries = 0; 217 218 if (!ds2482_select_register(pdev, DS2482_PTR_CODE_STATUS)) { 219 do { 220 temp = i2c_smbus_read_byte(pdev->client); 221 } while ((temp >= 0) && (temp & DS2482_REG_STS_1WB) && 222 (++retries < DS2482_WAIT_IDLE_TIMEOUT)); 223 } 224 225 if (retries >= DS2482_WAIT_IDLE_TIMEOUT) 226 pr_err("%s: timeout on channel %d\n", 227 __func__, pdev->channel); 228 229 return temp; 230 } 231 232 /** 233 * ds2482_set_channel - Selects a w1 channel. 234 * The 1-wire interface must be idle before calling this function. 235 * 236 * @pdev: The ds2482 client pointer 237 * @channel: 0-7 238 * Return: -1 (failure) or 0 (success) 239 */ 240 static int ds2482_set_channel(struct ds2482_data *pdev, u8 channel) 241 { 242 if (i2c_smbus_write_byte_data(pdev->client, DS2482_CMD_CHANNEL_SELECT, 243 ds2482_chan_wr[channel]) < 0) 244 return -1; 245 246 pdev->read_prt = DS2482_PTR_CODE_CHANNEL; 247 pdev->channel = -1; 248 if (i2c_smbus_read_byte(pdev->client) == ds2482_chan_rd[channel]) { 249 pdev->channel = channel; 250 return 0; 251 } 252 return -1; 253 } 254 255 256 /** 257 * ds2482_w1_touch_bit - Performs the touch-bit function, which writes a 0 or 1 and reads the level. 258 * 259 * @data: The ds2482 channel pointer 260 * @bit: The level to write: 0 or non-zero 261 * Return: The level read: 0 or 1 262 */ 263 static u8 ds2482_w1_touch_bit(void *data, u8 bit) 264 { 265 struct ds2482_w1_chan *pchan = data; 266 struct ds2482_data *pdev = pchan->pdev; 267 int status = -1; 268 269 mutex_lock(&pdev->access_lock); 270 271 /* Select the channel */ 272 ds2482_wait_1wire_idle(pdev); 273 if (pdev->w1_count > 1) 274 ds2482_set_channel(pdev, pchan->channel); 275 276 /* Send the touch command, wait until 1WB == 0, return the status */ 277 if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_SINGLE_BIT, 278 bit ? 0xFF : 0)) 279 status = ds2482_wait_1wire_idle(pdev); 280 281 mutex_unlock(&pdev->access_lock); 282 283 return (status & DS2482_REG_STS_SBR) ? 1 : 0; 284 } 285 286 /** 287 * ds2482_w1_triplet - Performs the triplet function, which reads two bits and writes a bit. 288 * The bit written is determined by the two reads: 289 * 00 => dbit, 01 => 0, 10 => 1 290 * 291 * @data: The ds2482 channel pointer 292 * @dbit: The direction to choose if both branches are valid 293 * Return: b0=read1 b1=read2 b3=bit written 294 */ 295 static u8 ds2482_w1_triplet(void *data, u8 dbit) 296 { 297 struct ds2482_w1_chan *pchan = data; 298 struct ds2482_data *pdev = pchan->pdev; 299 int status = (3 << 5); 300 301 mutex_lock(&pdev->access_lock); 302 303 /* Select the channel */ 304 ds2482_wait_1wire_idle(pdev); 305 if (pdev->w1_count > 1) 306 ds2482_set_channel(pdev, pchan->channel); 307 308 /* Send the triplet command, wait until 1WB == 0, return the status */ 309 if (!ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_TRIPLET, 310 dbit ? 0xFF : 0)) 311 status = ds2482_wait_1wire_idle(pdev); 312 313 mutex_unlock(&pdev->access_lock); 314 315 /* Decode the status */ 316 return (status >> 5); 317 } 318 319 /** 320 * ds2482_w1_write_byte - Performs the write byte function. 321 * 322 * @data: The ds2482 channel pointer 323 * @byte: The value to write 324 */ 325 static void ds2482_w1_write_byte(void *data, u8 byte) 326 { 327 struct ds2482_w1_chan *pchan = data; 328 struct ds2482_data *pdev = pchan->pdev; 329 330 mutex_lock(&pdev->access_lock); 331 332 /* Select the channel */ 333 ds2482_wait_1wire_idle(pdev); 334 if (pdev->w1_count > 1) 335 ds2482_set_channel(pdev, pchan->channel); 336 337 /* Send the write byte command */ 338 ds2482_send_cmd_data(pdev, DS2482_CMD_1WIRE_WRITE_BYTE, byte); 339 340 mutex_unlock(&pdev->access_lock); 341 } 342 343 /** 344 * ds2482_w1_read_byte - Performs the read byte function. 345 * 346 * @data: The ds2482 channel pointer 347 * Return: The value read 348 */ 349 static u8 ds2482_w1_read_byte(void *data) 350 { 351 struct ds2482_w1_chan *pchan = data; 352 struct ds2482_data *pdev = pchan->pdev; 353 int result; 354 355 mutex_lock(&pdev->access_lock); 356 357 /* Select the channel */ 358 ds2482_wait_1wire_idle(pdev); 359 if (pdev->w1_count > 1) 360 ds2482_set_channel(pdev, pchan->channel); 361 362 /* Send the read byte command */ 363 ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_READ_BYTE); 364 365 /* Wait until 1WB == 0 */ 366 ds2482_wait_1wire_idle(pdev); 367 368 /* Select the data register */ 369 ds2482_select_register(pdev, DS2482_PTR_CODE_DATA); 370 371 /* Read the data byte */ 372 result = i2c_smbus_read_byte(pdev->client); 373 374 mutex_unlock(&pdev->access_lock); 375 376 return result; 377 } 378 379 380 /** 381 * ds2482_w1_reset_bus - Sends a reset on the 1-wire interface 382 * 383 * @data: The ds2482 channel pointer 384 * Return: 0=Device present, 1=No device present or error 385 */ 386 static u8 ds2482_w1_reset_bus(void *data) 387 { 388 struct ds2482_w1_chan *pchan = data; 389 struct ds2482_data *pdev = pchan->pdev; 390 int err; 391 u8 retval = 1; 392 393 mutex_lock(&pdev->access_lock); 394 395 /* Select the channel */ 396 ds2482_wait_1wire_idle(pdev); 397 if (pdev->w1_count > 1) 398 ds2482_set_channel(pdev, pchan->channel); 399 400 /* Send the reset command */ 401 err = ds2482_send_cmd(pdev, DS2482_CMD_1WIRE_RESET); 402 if (err >= 0) { 403 /* Wait until the reset is complete */ 404 err = ds2482_wait_1wire_idle(pdev); 405 retval = !(err & DS2482_REG_STS_PPD); 406 407 /* If the chip did reset since detect, re-config it */ 408 if (err & DS2482_REG_STS_RST) 409 ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG, 410 ds2482_calculate_config(0x00)); 411 } 412 413 mutex_unlock(&pdev->access_lock); 414 415 return retval; 416 } 417 418 static u8 ds2482_w1_set_pullup(void *data, int delay) 419 { 420 struct ds2482_w1_chan *pchan = data; 421 struct ds2482_data *pdev = pchan->pdev; 422 u8 retval = 1; 423 424 /* if delay is non-zero activate the pullup, 425 * the strong pullup will be automatically deactivated 426 * by the master, so do not explicitly deactive it 427 */ 428 if (delay) { 429 /* both waits are crucial, otherwise devices might not be 430 * powered long enough, causing e.g. a w1_therm sensor to 431 * provide wrong conversion results 432 */ 433 ds2482_wait_1wire_idle(pdev); 434 /* note: it seems like both SPU and APU have to be set! */ 435 retval = ds2482_send_cmd_data(pdev, DS2482_CMD_WRITE_CONFIG, 436 ds2482_calculate_config(DS2482_REG_CFG_SPU | 437 DS2482_REG_CFG_APU)); 438 ds2482_wait_1wire_idle(pdev); 439 } 440 441 return retval; 442 } 443 444 445 static int ds2482_probe(struct i2c_client *client, 446 const struct i2c_device_id *id) 447 { 448 struct ds2482_data *data; 449 int err = -ENODEV; 450 int temp1; 451 int idx; 452 453 if (!i2c_check_functionality(client->adapter, 454 I2C_FUNC_SMBUS_WRITE_BYTE_DATA | 455 I2C_FUNC_SMBUS_BYTE)) 456 return -ENODEV; 457 458 if (!(data = kzalloc(sizeof(struct ds2482_data), GFP_KERNEL))) { 459 err = -ENOMEM; 460 goto exit; 461 } 462 463 data->client = client; 464 i2c_set_clientdata(client, data); 465 466 /* Reset the device (sets the read_ptr to status) */ 467 if (ds2482_send_cmd(data, DS2482_CMD_RESET) < 0) { 468 dev_warn(&client->dev, "DS2482 reset failed.\n"); 469 goto exit_free; 470 } 471 472 /* Sleep at least 525ns to allow the reset to complete */ 473 ndelay(525); 474 475 /* Read the status byte - only reset bit and line should be set */ 476 temp1 = i2c_smbus_read_byte(client); 477 if (temp1 != (DS2482_REG_STS_LL | DS2482_REG_STS_RST)) { 478 dev_warn(&client->dev, "DS2482 reset status " 479 "0x%02X - not a DS2482\n", temp1); 480 goto exit_free; 481 } 482 483 /* Detect the 8-port version */ 484 data->w1_count = 1; 485 if (ds2482_set_channel(data, 7) == 0) 486 data->w1_count = 8; 487 488 /* Set all config items to 0 (off) */ 489 ds2482_send_cmd_data(data, DS2482_CMD_WRITE_CONFIG, 490 ds2482_calculate_config(0x00)); 491 492 mutex_init(&data->access_lock); 493 494 /* Register 1-wire interface(s) */ 495 for (idx = 0; idx < data->w1_count; idx++) { 496 data->w1_ch[idx].pdev = data; 497 data->w1_ch[idx].channel = idx; 498 499 /* Populate all the w1 bus master stuff */ 500 data->w1_ch[idx].w1_bm.data = &data->w1_ch[idx]; 501 data->w1_ch[idx].w1_bm.read_byte = ds2482_w1_read_byte; 502 data->w1_ch[idx].w1_bm.write_byte = ds2482_w1_write_byte; 503 data->w1_ch[idx].w1_bm.touch_bit = ds2482_w1_touch_bit; 504 data->w1_ch[idx].w1_bm.triplet = ds2482_w1_triplet; 505 data->w1_ch[idx].w1_bm.reset_bus = ds2482_w1_reset_bus; 506 data->w1_ch[idx].w1_bm.set_pullup = ds2482_w1_set_pullup; 507 508 err = w1_add_master_device(&data->w1_ch[idx].w1_bm); 509 if (err) { 510 data->w1_ch[idx].pdev = NULL; 511 goto exit_w1_remove; 512 } 513 } 514 515 return 0; 516 517 exit_w1_remove: 518 for (idx = 0; idx < data->w1_count; idx++) { 519 if (data->w1_ch[idx].pdev != NULL) 520 w1_remove_master_device(&data->w1_ch[idx].w1_bm); 521 } 522 exit_free: 523 kfree(data); 524 exit: 525 return err; 526 } 527 528 static int ds2482_remove(struct i2c_client *client) 529 { 530 struct ds2482_data *data = i2c_get_clientdata(client); 531 int idx; 532 533 /* Unregister the 1-wire bridge(s) */ 534 for (idx = 0; idx < data->w1_count; idx++) { 535 if (data->w1_ch[idx].pdev != NULL) 536 w1_remove_master_device(&data->w1_ch[idx].w1_bm); 537 } 538 539 /* Free the memory */ 540 kfree(data); 541 return 0; 542 } 543 544 /* 545 * Driver data (common to all clients) 546 */ 547 static const struct i2c_device_id ds2482_id[] = { 548 { "ds2482", 0 }, 549 { } 550 }; 551 MODULE_DEVICE_TABLE(i2c, ds2482_id); 552 553 static struct i2c_driver ds2482_driver = { 554 .driver = { 555 .name = "ds2482", 556 }, 557 .probe = ds2482_probe, 558 .remove = ds2482_remove, 559 .id_table = ds2482_id, 560 }; 561 module_i2c_driver(ds2482_driver); 562 563 MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>"); 564 MODULE_DESCRIPTION("DS2482 driver"); 565 566 MODULE_LICENSE("GPL"); 567