1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Copyright (C) 2008-2009 MontaVista Software Inc. 4 * Copyright (C) 2008-2009 Texas Instruments Inc 5 * 6 * Based on the LCD driver for TI Avalanche processors written by 7 * Ajay Singh and Shalom Hai. 8 */ 9 #include <linux/module.h> 10 #include <linux/kernel.h> 11 #include <linux/fb.h> 12 #include <linux/dma-mapping.h> 13 #include <linux/device.h> 14 #include <linux/platform_device.h> 15 #include <linux/uaccess.h> 16 #include <linux/pm_runtime.h> 17 #include <linux/interrupt.h> 18 #include <linux/wait.h> 19 #include <linux/clk.h> 20 #include <linux/cpufreq.h> 21 #include <linux/console.h> 22 #include <linux/regulator/consumer.h> 23 #include <linux/spinlock.h> 24 #include <linux/slab.h> 25 #include <linux/delay.h> 26 #include <linux/lcm.h> 27 #include <video/da8xx-fb.h> 28 #include <asm/div64.h> 29 30 #define DRIVER_NAME "da8xx_lcdc" 31 32 #define LCD_VERSION_1 1 33 #define LCD_VERSION_2 2 34 35 /* LCD Status Register */ 36 #define LCD_END_OF_FRAME1 BIT(9) 37 #define LCD_END_OF_FRAME0 BIT(8) 38 #define LCD_PL_LOAD_DONE BIT(6) 39 #define LCD_FIFO_UNDERFLOW BIT(5) 40 #define LCD_SYNC_LOST BIT(2) 41 #define LCD_FRAME_DONE BIT(0) 42 43 /* LCD DMA Control Register */ 44 #define LCD_DMA_BURST_SIZE(x) ((x) << 4) 45 #define LCD_DMA_BURST_1 0x0 46 #define LCD_DMA_BURST_2 0x1 47 #define LCD_DMA_BURST_4 0x2 48 #define LCD_DMA_BURST_8 0x3 49 #define LCD_DMA_BURST_16 0x4 50 #define LCD_V1_END_OF_FRAME_INT_ENA BIT(2) 51 #define LCD_V2_END_OF_FRAME0_INT_ENA BIT(8) 52 #define LCD_V2_END_OF_FRAME1_INT_ENA BIT(9) 53 #define LCD_DUAL_FRAME_BUFFER_ENABLE BIT(0) 54 55 /* LCD Control Register */ 56 #define LCD_CLK_DIVISOR(x) ((x) << 8) 57 #define LCD_RASTER_MODE 0x01 58 59 /* LCD Raster Control Register */ 60 #define LCD_PALETTE_LOAD_MODE(x) ((x) << 20) 61 #define PALETTE_AND_DATA 0x00 62 #define PALETTE_ONLY 0x01 63 #define DATA_ONLY 0x02 64 65 #define LCD_MONO_8BIT_MODE BIT(9) 66 #define LCD_RASTER_ORDER BIT(8) 67 #define LCD_TFT_MODE BIT(7) 68 #define LCD_V1_UNDERFLOW_INT_ENA BIT(6) 69 #define LCD_V2_UNDERFLOW_INT_ENA BIT(5) 70 #define LCD_V1_PL_INT_ENA BIT(4) 71 #define LCD_V2_PL_INT_ENA BIT(6) 72 #define LCD_MONOCHROME_MODE BIT(1) 73 #define LCD_RASTER_ENABLE BIT(0) 74 #define LCD_TFT_ALT_ENABLE BIT(23) 75 #define LCD_STN_565_ENABLE BIT(24) 76 #define LCD_V2_DMA_CLK_EN BIT(2) 77 #define LCD_V2_LIDD_CLK_EN BIT(1) 78 #define LCD_V2_CORE_CLK_EN BIT(0) 79 #define LCD_V2_LPP_B10 26 80 #define LCD_V2_TFT_24BPP_MODE BIT(25) 81 #define LCD_V2_TFT_24BPP_UNPACK BIT(26) 82 83 /* LCD Raster Timing 2 Register */ 84 #define LCD_AC_BIAS_TRANSITIONS_PER_INT(x) ((x) << 16) 85 #define LCD_AC_BIAS_FREQUENCY(x) ((x) << 8) 86 #define LCD_SYNC_CTRL BIT(25) 87 #define LCD_SYNC_EDGE BIT(24) 88 #define LCD_INVERT_PIXEL_CLOCK BIT(22) 89 #define LCD_INVERT_LINE_CLOCK BIT(21) 90 #define LCD_INVERT_FRAME_CLOCK BIT(20) 91 92 /* LCD Block */ 93 #define LCD_PID_REG 0x0 94 #define LCD_CTRL_REG 0x4 95 #define LCD_STAT_REG 0x8 96 #define LCD_RASTER_CTRL_REG 0x28 97 #define LCD_RASTER_TIMING_0_REG 0x2C 98 #define LCD_RASTER_TIMING_1_REG 0x30 99 #define LCD_RASTER_TIMING_2_REG 0x34 100 #define LCD_DMA_CTRL_REG 0x40 101 #define LCD_DMA_FRM_BUF_BASE_ADDR_0_REG 0x44 102 #define LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG 0x48 103 #define LCD_DMA_FRM_BUF_BASE_ADDR_1_REG 0x4C 104 #define LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG 0x50 105 106 /* Interrupt Registers available only in Version 2 */ 107 #define LCD_RAW_STAT_REG 0x58 108 #define LCD_MASKED_STAT_REG 0x5c 109 #define LCD_INT_ENABLE_SET_REG 0x60 110 #define LCD_INT_ENABLE_CLR_REG 0x64 111 #define LCD_END_OF_INT_IND_REG 0x68 112 113 /* Clock registers available only on Version 2 */ 114 #define LCD_CLK_ENABLE_REG 0x6c 115 #define LCD_CLK_RESET_REG 0x70 116 #define LCD_CLK_MAIN_RESET BIT(3) 117 118 #define LCD_NUM_BUFFERS 2 119 120 #define PALETTE_SIZE 256 121 122 #define CLK_MIN_DIV 2 123 #define CLK_MAX_DIV 255 124 125 static void __iomem *da8xx_fb_reg_base; 126 static unsigned int lcd_revision; 127 static irq_handler_t lcdc_irq_handler; 128 static wait_queue_head_t frame_done_wq; 129 static int frame_done_flag; 130 131 static unsigned int lcdc_read(unsigned int addr) 132 { 133 return (unsigned int)__raw_readl(da8xx_fb_reg_base + (addr)); 134 } 135 136 static void lcdc_write(unsigned int val, unsigned int addr) 137 { 138 __raw_writel(val, da8xx_fb_reg_base + (addr)); 139 } 140 141 struct da8xx_fb_par { 142 struct device *dev; 143 dma_addr_t p_palette_base; 144 unsigned char *v_palette_base; 145 dma_addr_t vram_phys; 146 unsigned long vram_size; 147 void *vram_virt; 148 unsigned int dma_start; 149 unsigned int dma_end; 150 struct clk *lcdc_clk; 151 int irq; 152 unsigned int palette_sz; 153 int blank; 154 wait_queue_head_t vsync_wait; 155 int vsync_flag; 156 int vsync_timeout; 157 spinlock_t lock_for_chan_update; 158 159 /* 160 * LCDC has 2 ping pong DMA channels, channel 0 161 * and channel 1. 162 */ 163 unsigned int which_dma_channel_done; 164 #ifdef CONFIG_CPU_FREQ 165 struct notifier_block freq_transition; 166 #endif 167 unsigned int lcdc_clk_rate; 168 struct regulator *lcd_supply; 169 u32 pseudo_palette[16]; 170 struct fb_videomode mode; 171 struct lcd_ctrl_config cfg; 172 }; 173 174 static struct fb_var_screeninfo da8xx_fb_var; 175 176 static struct fb_fix_screeninfo da8xx_fb_fix = { 177 .id = "DA8xx FB Drv", 178 .type = FB_TYPE_PACKED_PIXELS, 179 .type_aux = 0, 180 .visual = FB_VISUAL_PSEUDOCOLOR, 181 .xpanstep = 0, 182 .ypanstep = 1, 183 .ywrapstep = 0, 184 .accel = FB_ACCEL_NONE 185 }; 186 187 static struct fb_videomode known_lcd_panels[] = { 188 /* Sharp LCD035Q3DG01 */ 189 [0] = { 190 .name = "Sharp_LCD035Q3DG01", 191 .xres = 320, 192 .yres = 240, 193 .pixclock = KHZ2PICOS(4607), 194 .left_margin = 6, 195 .right_margin = 8, 196 .upper_margin = 2, 197 .lower_margin = 2, 198 .hsync_len = 0, 199 .vsync_len = 0, 200 .sync = FB_SYNC_CLK_INVERT, 201 }, 202 /* Sharp LK043T1DG01 */ 203 [1] = { 204 .name = "Sharp_LK043T1DG01", 205 .xres = 480, 206 .yres = 272, 207 .pixclock = KHZ2PICOS(7833), 208 .left_margin = 2, 209 .right_margin = 2, 210 .upper_margin = 2, 211 .lower_margin = 2, 212 .hsync_len = 41, 213 .vsync_len = 10, 214 .sync = 0, 215 .flag = 0, 216 }, 217 [2] = { 218 /* Hitachi SP10Q010 */ 219 .name = "SP10Q010", 220 .xres = 320, 221 .yres = 240, 222 .pixclock = KHZ2PICOS(7833), 223 .left_margin = 10, 224 .right_margin = 10, 225 .upper_margin = 10, 226 .lower_margin = 10, 227 .hsync_len = 10, 228 .vsync_len = 10, 229 .sync = 0, 230 .flag = 0, 231 }, 232 [3] = { 233 /* Densitron 84-0023-001T */ 234 .name = "Densitron_84-0023-001T", 235 .xres = 320, 236 .yres = 240, 237 .pixclock = KHZ2PICOS(6400), 238 .left_margin = 0, 239 .right_margin = 0, 240 .upper_margin = 0, 241 .lower_margin = 0, 242 .hsync_len = 30, 243 .vsync_len = 3, 244 .sync = 0, 245 }, 246 }; 247 248 static bool da8xx_fb_is_raster_enabled(void) 249 { 250 return !!(lcdc_read(LCD_RASTER_CTRL_REG) & LCD_RASTER_ENABLE); 251 } 252 253 /* Enable the Raster Engine of the LCD Controller */ 254 static void lcd_enable_raster(void) 255 { 256 u32 reg; 257 258 /* Put LCDC in reset for several cycles */ 259 if (lcd_revision == LCD_VERSION_2) 260 /* Write 1 to reset LCDC */ 261 lcdc_write(LCD_CLK_MAIN_RESET, LCD_CLK_RESET_REG); 262 mdelay(1); 263 264 /* Bring LCDC out of reset */ 265 if (lcd_revision == LCD_VERSION_2) 266 lcdc_write(0, LCD_CLK_RESET_REG); 267 mdelay(1); 268 269 /* Above reset sequence doesnot reset register context */ 270 reg = lcdc_read(LCD_RASTER_CTRL_REG); 271 if (!(reg & LCD_RASTER_ENABLE)) 272 lcdc_write(reg | LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); 273 } 274 275 /* Disable the Raster Engine of the LCD Controller */ 276 static void lcd_disable_raster(enum da8xx_frame_complete wait_for_frame_done) 277 { 278 u32 reg; 279 int ret; 280 281 reg = lcdc_read(LCD_RASTER_CTRL_REG); 282 if (reg & LCD_RASTER_ENABLE) 283 lcdc_write(reg & ~LCD_RASTER_ENABLE, LCD_RASTER_CTRL_REG); 284 else 285 /* return if already disabled */ 286 return; 287 288 if ((wait_for_frame_done == DA8XX_FRAME_WAIT) && 289 (lcd_revision == LCD_VERSION_2)) { 290 frame_done_flag = 0; 291 ret = wait_event_interruptible_timeout(frame_done_wq, 292 frame_done_flag != 0, 293 msecs_to_jiffies(50)); 294 if (ret == 0) 295 pr_err("LCD Controller timed out\n"); 296 } 297 } 298 299 static void lcd_blit(int load_mode, struct da8xx_fb_par *par) 300 { 301 u32 start; 302 u32 end; 303 u32 reg_ras; 304 u32 reg_dma; 305 u32 reg_int; 306 307 /* init reg to clear PLM (loading mode) fields */ 308 reg_ras = lcdc_read(LCD_RASTER_CTRL_REG); 309 reg_ras &= ~(3 << 20); 310 311 reg_dma = lcdc_read(LCD_DMA_CTRL_REG); 312 313 if (load_mode == LOAD_DATA) { 314 start = par->dma_start; 315 end = par->dma_end; 316 317 reg_ras |= LCD_PALETTE_LOAD_MODE(DATA_ONLY); 318 if (lcd_revision == LCD_VERSION_1) { 319 reg_dma |= LCD_V1_END_OF_FRAME_INT_ENA; 320 } else { 321 reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) | 322 LCD_V2_END_OF_FRAME0_INT_ENA | 323 LCD_V2_END_OF_FRAME1_INT_ENA | 324 LCD_FRAME_DONE | LCD_SYNC_LOST; 325 lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG); 326 } 327 reg_dma |= LCD_DUAL_FRAME_BUFFER_ENABLE; 328 329 lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 330 lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 331 lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 332 lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 333 } else if (load_mode == LOAD_PALETTE) { 334 start = par->p_palette_base; 335 end = start + par->palette_sz - 1; 336 337 reg_ras |= LCD_PALETTE_LOAD_MODE(PALETTE_ONLY); 338 339 if (lcd_revision == LCD_VERSION_1) { 340 reg_ras |= LCD_V1_PL_INT_ENA; 341 } else { 342 reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) | 343 LCD_V2_PL_INT_ENA; 344 lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG); 345 } 346 347 lcdc_write(start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 348 lcdc_write(end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 349 } 350 351 lcdc_write(reg_dma, LCD_DMA_CTRL_REG); 352 lcdc_write(reg_ras, LCD_RASTER_CTRL_REG); 353 354 /* 355 * The Raster enable bit must be set after all other control fields are 356 * set. 357 */ 358 lcd_enable_raster(); 359 } 360 361 /* Configure the Burst Size and fifo threhold of DMA */ 362 static int lcd_cfg_dma(int burst_size, int fifo_th) 363 { 364 u32 reg; 365 366 reg = lcdc_read(LCD_DMA_CTRL_REG) & 0x00000001; 367 switch (burst_size) { 368 case 1: 369 reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_1); 370 break; 371 case 2: 372 reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_2); 373 break; 374 case 4: 375 reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_4); 376 break; 377 case 8: 378 reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_8); 379 break; 380 case 16: 381 default: 382 reg |= LCD_DMA_BURST_SIZE(LCD_DMA_BURST_16); 383 break; 384 } 385 386 reg |= (fifo_th << 8); 387 388 lcdc_write(reg, LCD_DMA_CTRL_REG); 389 390 return 0; 391 } 392 393 static void lcd_cfg_ac_bias(int period, int transitions_per_int) 394 { 395 u32 reg; 396 397 /* Set the AC Bias Period and Number of Transisitons per Interrupt */ 398 reg = lcdc_read(LCD_RASTER_TIMING_2_REG) & 0xFFF00000; 399 reg |= LCD_AC_BIAS_FREQUENCY(period) | 400 LCD_AC_BIAS_TRANSITIONS_PER_INT(transitions_per_int); 401 lcdc_write(reg, LCD_RASTER_TIMING_2_REG); 402 } 403 404 static void lcd_cfg_horizontal_sync(int back_porch, int pulse_width, 405 int front_porch) 406 { 407 u32 reg; 408 409 reg = lcdc_read(LCD_RASTER_TIMING_0_REG) & 0x3ff; 410 reg |= (((back_porch-1) & 0xff) << 24) 411 | (((front_porch-1) & 0xff) << 16) 412 | (((pulse_width-1) & 0x3f) << 10); 413 lcdc_write(reg, LCD_RASTER_TIMING_0_REG); 414 415 /* 416 * LCDC Version 2 adds some extra bits that increase the allowable 417 * size of the horizontal timing registers. 418 * remember that the registers use 0 to represent 1 so all values 419 * that get set into register need to be decremented by 1 420 */ 421 if (lcd_revision == LCD_VERSION_2) { 422 /* Mask off the bits we want to change */ 423 reg = lcdc_read(LCD_RASTER_TIMING_2_REG) & ~0x780000ff; 424 reg |= ((front_porch-1) & 0x300) >> 8; 425 reg |= ((back_porch-1) & 0x300) >> 4; 426 reg |= ((pulse_width-1) & 0x3c0) << 21; 427 lcdc_write(reg, LCD_RASTER_TIMING_2_REG); 428 } 429 } 430 431 static void lcd_cfg_vertical_sync(int back_porch, int pulse_width, 432 int front_porch) 433 { 434 u32 reg; 435 436 reg = lcdc_read(LCD_RASTER_TIMING_1_REG) & 0x3ff; 437 reg |= ((back_porch & 0xff) << 24) 438 | ((front_porch & 0xff) << 16) 439 | (((pulse_width-1) & 0x3f) << 10); 440 lcdc_write(reg, LCD_RASTER_TIMING_1_REG); 441 } 442 443 static int lcd_cfg_display(const struct lcd_ctrl_config *cfg, 444 struct fb_videomode *panel) 445 { 446 u32 reg; 447 u32 reg_int; 448 449 reg = lcdc_read(LCD_RASTER_CTRL_REG) & ~(LCD_TFT_MODE | 450 LCD_MONO_8BIT_MODE | 451 LCD_MONOCHROME_MODE); 452 453 switch (cfg->panel_shade) { 454 case MONOCHROME: 455 reg |= LCD_MONOCHROME_MODE; 456 if (cfg->mono_8bit_mode) 457 reg |= LCD_MONO_8BIT_MODE; 458 break; 459 case COLOR_ACTIVE: 460 reg |= LCD_TFT_MODE; 461 if (cfg->tft_alt_mode) 462 reg |= LCD_TFT_ALT_ENABLE; 463 break; 464 465 case COLOR_PASSIVE: 466 /* AC bias applicable only for Pasive panels */ 467 lcd_cfg_ac_bias(cfg->ac_bias, cfg->ac_bias_intrpt); 468 if (cfg->bpp == 12 && cfg->stn_565_mode) 469 reg |= LCD_STN_565_ENABLE; 470 break; 471 472 default: 473 return -EINVAL; 474 } 475 476 /* enable additional interrupts here */ 477 if (lcd_revision == LCD_VERSION_1) { 478 reg |= LCD_V1_UNDERFLOW_INT_ENA; 479 } else { 480 reg_int = lcdc_read(LCD_INT_ENABLE_SET_REG) | 481 LCD_V2_UNDERFLOW_INT_ENA; 482 lcdc_write(reg_int, LCD_INT_ENABLE_SET_REG); 483 } 484 485 lcdc_write(reg, LCD_RASTER_CTRL_REG); 486 487 reg = lcdc_read(LCD_RASTER_TIMING_2_REG); 488 489 reg |= LCD_SYNC_CTRL; 490 491 if (cfg->sync_edge) 492 reg |= LCD_SYNC_EDGE; 493 else 494 reg &= ~LCD_SYNC_EDGE; 495 496 if ((panel->sync & FB_SYNC_HOR_HIGH_ACT) == 0) 497 reg |= LCD_INVERT_LINE_CLOCK; 498 else 499 reg &= ~LCD_INVERT_LINE_CLOCK; 500 501 if ((panel->sync & FB_SYNC_VERT_HIGH_ACT) == 0) 502 reg |= LCD_INVERT_FRAME_CLOCK; 503 else 504 reg &= ~LCD_INVERT_FRAME_CLOCK; 505 506 lcdc_write(reg, LCD_RASTER_TIMING_2_REG); 507 508 return 0; 509 } 510 511 static int lcd_cfg_frame_buffer(struct da8xx_fb_par *par, u32 width, u32 height, 512 u32 bpp, u32 raster_order) 513 { 514 u32 reg; 515 516 if (bpp > 16 && lcd_revision == LCD_VERSION_1) 517 return -EINVAL; 518 519 /* Set the Panel Width */ 520 /* Pixels per line = (PPL + 1)*16 */ 521 if (lcd_revision == LCD_VERSION_1) { 522 /* 523 * 0x3F in bits 4..9 gives max horizontal resolution = 1024 524 * pixels. 525 */ 526 width &= 0x3f0; 527 } else { 528 /* 529 * 0x7F in bits 4..10 gives max horizontal resolution = 2048 530 * pixels. 531 */ 532 width &= 0x7f0; 533 } 534 535 reg = lcdc_read(LCD_RASTER_TIMING_0_REG); 536 reg &= 0xfffffc00; 537 if (lcd_revision == LCD_VERSION_1) { 538 reg |= ((width >> 4) - 1) << 4; 539 } else { 540 width = (width >> 4) - 1; 541 reg |= ((width & 0x3f) << 4) | ((width & 0x40) >> 3); 542 } 543 lcdc_write(reg, LCD_RASTER_TIMING_0_REG); 544 545 /* Set the Panel Height */ 546 /* Set bits 9:0 of Lines Per Pixel */ 547 reg = lcdc_read(LCD_RASTER_TIMING_1_REG); 548 reg = ((height - 1) & 0x3ff) | (reg & 0xfffffc00); 549 lcdc_write(reg, LCD_RASTER_TIMING_1_REG); 550 551 /* Set bit 10 of Lines Per Pixel */ 552 if (lcd_revision == LCD_VERSION_2) { 553 reg = lcdc_read(LCD_RASTER_TIMING_2_REG); 554 reg |= ((height - 1) & 0x400) << 16; 555 lcdc_write(reg, LCD_RASTER_TIMING_2_REG); 556 } 557 558 /* Set the Raster Order of the Frame Buffer */ 559 reg = lcdc_read(LCD_RASTER_CTRL_REG) & ~(1 << 8); 560 if (raster_order) 561 reg |= LCD_RASTER_ORDER; 562 563 par->palette_sz = 16 * 2; 564 565 switch (bpp) { 566 case 1: 567 case 2: 568 case 4: 569 case 16: 570 break; 571 case 24: 572 reg |= LCD_V2_TFT_24BPP_MODE; 573 break; 574 case 32: 575 reg |= LCD_V2_TFT_24BPP_MODE; 576 reg |= LCD_V2_TFT_24BPP_UNPACK; 577 break; 578 case 8: 579 par->palette_sz = 256 * 2; 580 break; 581 582 default: 583 return -EINVAL; 584 } 585 586 lcdc_write(reg, LCD_RASTER_CTRL_REG); 587 588 return 0; 589 } 590 591 #define CNVT_TOHW(val, width) ((((val) << (width)) + 0x7FFF - (val)) >> 16) 592 static int fb_setcolreg(unsigned regno, unsigned red, unsigned green, 593 unsigned blue, unsigned transp, 594 struct fb_info *info) 595 { 596 struct da8xx_fb_par *par = info->par; 597 unsigned short *palette = (unsigned short *) par->v_palette_base; 598 u_short pal; 599 int update_hw = 0; 600 601 if (regno > 255) 602 return 1; 603 604 if (info->fix.visual == FB_VISUAL_DIRECTCOLOR) 605 return 1; 606 607 if (info->var.bits_per_pixel > 16 && lcd_revision == LCD_VERSION_1) 608 return -EINVAL; 609 610 switch (info->fix.visual) { 611 case FB_VISUAL_TRUECOLOR: 612 red = CNVT_TOHW(red, info->var.red.length); 613 green = CNVT_TOHW(green, info->var.green.length); 614 blue = CNVT_TOHW(blue, info->var.blue.length); 615 break; 616 case FB_VISUAL_PSEUDOCOLOR: 617 switch (info->var.bits_per_pixel) { 618 case 4: 619 if (regno > 15) 620 return -EINVAL; 621 622 if (info->var.grayscale) { 623 pal = regno; 624 } else { 625 red >>= 4; 626 green >>= 8; 627 blue >>= 12; 628 629 pal = red & 0x0f00; 630 pal |= green & 0x00f0; 631 pal |= blue & 0x000f; 632 } 633 if (regno == 0) 634 pal |= 0x2000; 635 palette[regno] = pal; 636 break; 637 638 case 8: 639 red >>= 4; 640 green >>= 8; 641 blue >>= 12; 642 643 pal = (red & 0x0f00); 644 pal |= (green & 0x00f0); 645 pal |= (blue & 0x000f); 646 647 if (palette[regno] != pal) { 648 update_hw = 1; 649 palette[regno] = pal; 650 } 651 break; 652 } 653 break; 654 } 655 656 /* Truecolor has hardware independent palette */ 657 if (info->fix.visual == FB_VISUAL_TRUECOLOR) { 658 u32 v; 659 660 if (regno > 15) 661 return -EINVAL; 662 663 v = (red << info->var.red.offset) | 664 (green << info->var.green.offset) | 665 (blue << info->var.blue.offset); 666 667 ((u32 *) (info->pseudo_palette))[regno] = v; 668 if (palette[0] != 0x4000) { 669 update_hw = 1; 670 palette[0] = 0x4000; 671 } 672 } 673 674 /* Update the palette in the h/w as needed. */ 675 if (update_hw) 676 lcd_blit(LOAD_PALETTE, par); 677 678 return 0; 679 } 680 #undef CNVT_TOHW 681 682 static void da8xx_fb_lcd_reset(void) 683 { 684 /* DMA has to be disabled */ 685 lcdc_write(0, LCD_DMA_CTRL_REG); 686 lcdc_write(0, LCD_RASTER_CTRL_REG); 687 688 if (lcd_revision == LCD_VERSION_2) { 689 lcdc_write(0, LCD_INT_ENABLE_SET_REG); 690 /* Write 1 to reset */ 691 lcdc_write(LCD_CLK_MAIN_RESET, LCD_CLK_RESET_REG); 692 lcdc_write(0, LCD_CLK_RESET_REG); 693 } 694 } 695 696 static int da8xx_fb_config_clk_divider(struct da8xx_fb_par *par, 697 unsigned lcdc_clk_div, 698 unsigned lcdc_clk_rate) 699 { 700 int ret; 701 702 if (par->lcdc_clk_rate != lcdc_clk_rate) { 703 ret = clk_set_rate(par->lcdc_clk, lcdc_clk_rate); 704 if (ret) { 705 dev_err(par->dev, 706 "unable to set clock rate at %u\n", 707 lcdc_clk_rate); 708 return ret; 709 } 710 par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk); 711 } 712 713 /* Configure the LCD clock divisor. */ 714 lcdc_write(LCD_CLK_DIVISOR(lcdc_clk_div) | 715 (LCD_RASTER_MODE & 0x1), LCD_CTRL_REG); 716 717 if (lcd_revision == LCD_VERSION_2) 718 lcdc_write(LCD_V2_DMA_CLK_EN | LCD_V2_LIDD_CLK_EN | 719 LCD_V2_CORE_CLK_EN, LCD_CLK_ENABLE_REG); 720 721 return 0; 722 } 723 724 static unsigned int da8xx_fb_calc_clk_divider(struct da8xx_fb_par *par, 725 unsigned pixclock, 726 unsigned *lcdc_clk_rate) 727 { 728 unsigned lcdc_clk_div; 729 730 pixclock = PICOS2KHZ(pixclock) * 1000; 731 732 *lcdc_clk_rate = par->lcdc_clk_rate; 733 734 if (pixclock < (*lcdc_clk_rate / CLK_MAX_DIV)) { 735 *lcdc_clk_rate = clk_round_rate(par->lcdc_clk, 736 pixclock * CLK_MAX_DIV); 737 lcdc_clk_div = CLK_MAX_DIV; 738 } else if (pixclock > (*lcdc_clk_rate / CLK_MIN_DIV)) { 739 *lcdc_clk_rate = clk_round_rate(par->lcdc_clk, 740 pixclock * CLK_MIN_DIV); 741 lcdc_clk_div = CLK_MIN_DIV; 742 } else { 743 lcdc_clk_div = *lcdc_clk_rate / pixclock; 744 } 745 746 return lcdc_clk_div; 747 } 748 749 static int da8xx_fb_calc_config_clk_divider(struct da8xx_fb_par *par, 750 struct fb_videomode *mode) 751 { 752 unsigned lcdc_clk_rate; 753 unsigned lcdc_clk_div = da8xx_fb_calc_clk_divider(par, mode->pixclock, 754 &lcdc_clk_rate); 755 756 return da8xx_fb_config_clk_divider(par, lcdc_clk_div, lcdc_clk_rate); 757 } 758 759 static unsigned da8xx_fb_round_clk(struct da8xx_fb_par *par, 760 unsigned pixclock) 761 { 762 unsigned lcdc_clk_div, lcdc_clk_rate; 763 764 lcdc_clk_div = da8xx_fb_calc_clk_divider(par, pixclock, &lcdc_clk_rate); 765 return KHZ2PICOS(lcdc_clk_rate / (1000 * lcdc_clk_div)); 766 } 767 768 static int lcd_init(struct da8xx_fb_par *par, const struct lcd_ctrl_config *cfg, 769 struct fb_videomode *panel) 770 { 771 u32 bpp; 772 int ret = 0; 773 774 ret = da8xx_fb_calc_config_clk_divider(par, panel); 775 if (ret) { 776 dev_err(par->dev, "unable to configure clock\n"); 777 return ret; 778 } 779 780 if (panel->sync & FB_SYNC_CLK_INVERT) 781 lcdc_write((lcdc_read(LCD_RASTER_TIMING_2_REG) | 782 LCD_INVERT_PIXEL_CLOCK), LCD_RASTER_TIMING_2_REG); 783 else 784 lcdc_write((lcdc_read(LCD_RASTER_TIMING_2_REG) & 785 ~LCD_INVERT_PIXEL_CLOCK), LCD_RASTER_TIMING_2_REG); 786 787 /* Configure the DMA burst size and fifo threshold. */ 788 ret = lcd_cfg_dma(cfg->dma_burst_sz, cfg->fifo_th); 789 if (ret < 0) 790 return ret; 791 792 /* Configure the vertical and horizontal sync properties. */ 793 lcd_cfg_vertical_sync(panel->upper_margin, panel->vsync_len, 794 panel->lower_margin); 795 lcd_cfg_horizontal_sync(panel->left_margin, panel->hsync_len, 796 panel->right_margin); 797 798 /* Configure for disply */ 799 ret = lcd_cfg_display(cfg, panel); 800 if (ret < 0) 801 return ret; 802 803 bpp = cfg->bpp; 804 805 if (bpp == 12) 806 bpp = 16; 807 ret = lcd_cfg_frame_buffer(par, (unsigned int)panel->xres, 808 (unsigned int)panel->yres, bpp, 809 cfg->raster_order); 810 if (ret < 0) 811 return ret; 812 813 /* Configure FDD */ 814 lcdc_write((lcdc_read(LCD_RASTER_CTRL_REG) & 0xfff00fff) | 815 (cfg->fdd << 12), LCD_RASTER_CTRL_REG); 816 817 return 0; 818 } 819 820 /* IRQ handler for version 2 of LCDC */ 821 static irqreturn_t lcdc_irq_handler_rev02(int irq, void *arg) 822 { 823 struct da8xx_fb_par *par = arg; 824 u32 stat = lcdc_read(LCD_MASKED_STAT_REG); 825 826 if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) { 827 lcd_disable_raster(DA8XX_FRAME_NOWAIT); 828 lcdc_write(stat, LCD_MASKED_STAT_REG); 829 lcd_enable_raster(); 830 } else if (stat & LCD_PL_LOAD_DONE) { 831 /* 832 * Must disable raster before changing state of any control bit. 833 * And also must be disabled before clearing the PL loading 834 * interrupt via the following write to the status register. If 835 * this is done after then one gets multiple PL done interrupts. 836 */ 837 lcd_disable_raster(DA8XX_FRAME_NOWAIT); 838 839 lcdc_write(stat, LCD_MASKED_STAT_REG); 840 841 /* Disable PL completion interrupt */ 842 lcdc_write(LCD_V2_PL_INT_ENA, LCD_INT_ENABLE_CLR_REG); 843 844 /* Setup and start data loading mode */ 845 lcd_blit(LOAD_DATA, par); 846 } else { 847 lcdc_write(stat, LCD_MASKED_STAT_REG); 848 849 if (stat & LCD_END_OF_FRAME0) { 850 par->which_dma_channel_done = 0; 851 lcdc_write(par->dma_start, 852 LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 853 lcdc_write(par->dma_end, 854 LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 855 par->vsync_flag = 1; 856 wake_up_interruptible(&par->vsync_wait); 857 } 858 859 if (stat & LCD_END_OF_FRAME1) { 860 par->which_dma_channel_done = 1; 861 lcdc_write(par->dma_start, 862 LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 863 lcdc_write(par->dma_end, 864 LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 865 par->vsync_flag = 1; 866 wake_up_interruptible(&par->vsync_wait); 867 } 868 869 /* Set only when controller is disabled and at the end of 870 * active frame 871 */ 872 if (stat & BIT(0)) { 873 frame_done_flag = 1; 874 wake_up_interruptible(&frame_done_wq); 875 } 876 } 877 878 lcdc_write(0, LCD_END_OF_INT_IND_REG); 879 return IRQ_HANDLED; 880 } 881 882 /* IRQ handler for version 1 LCDC */ 883 static irqreturn_t lcdc_irq_handler_rev01(int irq, void *arg) 884 { 885 struct da8xx_fb_par *par = arg; 886 u32 stat = lcdc_read(LCD_STAT_REG); 887 u32 reg_ras; 888 889 if ((stat & LCD_SYNC_LOST) && (stat & LCD_FIFO_UNDERFLOW)) { 890 lcd_disable_raster(DA8XX_FRAME_NOWAIT); 891 lcdc_write(stat, LCD_STAT_REG); 892 lcd_enable_raster(); 893 } else if (stat & LCD_PL_LOAD_DONE) { 894 /* 895 * Must disable raster before changing state of any control bit. 896 * And also must be disabled before clearing the PL loading 897 * interrupt via the following write to the status register. If 898 * this is done after then one gets multiple PL done interrupts. 899 */ 900 lcd_disable_raster(DA8XX_FRAME_NOWAIT); 901 902 lcdc_write(stat, LCD_STAT_REG); 903 904 /* Disable PL completion inerrupt */ 905 reg_ras = lcdc_read(LCD_RASTER_CTRL_REG); 906 reg_ras &= ~LCD_V1_PL_INT_ENA; 907 lcdc_write(reg_ras, LCD_RASTER_CTRL_REG); 908 909 /* Setup and start data loading mode */ 910 lcd_blit(LOAD_DATA, par); 911 } else { 912 lcdc_write(stat, LCD_STAT_REG); 913 914 if (stat & LCD_END_OF_FRAME0) { 915 par->which_dma_channel_done = 0; 916 lcdc_write(par->dma_start, 917 LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 918 lcdc_write(par->dma_end, 919 LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 920 par->vsync_flag = 1; 921 wake_up_interruptible(&par->vsync_wait); 922 } 923 924 if (stat & LCD_END_OF_FRAME1) { 925 par->which_dma_channel_done = 1; 926 lcdc_write(par->dma_start, 927 LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 928 lcdc_write(par->dma_end, 929 LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 930 par->vsync_flag = 1; 931 wake_up_interruptible(&par->vsync_wait); 932 } 933 } 934 935 return IRQ_HANDLED; 936 } 937 938 static int fb_check_var(struct fb_var_screeninfo *var, 939 struct fb_info *info) 940 { 941 int err = 0; 942 struct da8xx_fb_par *par = info->par; 943 int bpp = var->bits_per_pixel >> 3; 944 unsigned long line_size = var->xres_virtual * bpp; 945 946 if (var->bits_per_pixel > 16 && lcd_revision == LCD_VERSION_1) 947 return -EINVAL; 948 949 switch (var->bits_per_pixel) { 950 case 1: 951 case 8: 952 var->red.offset = 0; 953 var->red.length = 8; 954 var->green.offset = 0; 955 var->green.length = 8; 956 var->blue.offset = 0; 957 var->blue.length = 8; 958 var->transp.offset = 0; 959 var->transp.length = 0; 960 var->nonstd = 0; 961 break; 962 case 4: 963 var->red.offset = 0; 964 var->red.length = 4; 965 var->green.offset = 0; 966 var->green.length = 4; 967 var->blue.offset = 0; 968 var->blue.length = 4; 969 var->transp.offset = 0; 970 var->transp.length = 0; 971 var->nonstd = FB_NONSTD_REV_PIX_IN_B; 972 break; 973 case 16: /* RGB 565 */ 974 var->red.offset = 11; 975 var->red.length = 5; 976 var->green.offset = 5; 977 var->green.length = 6; 978 var->blue.offset = 0; 979 var->blue.length = 5; 980 var->transp.offset = 0; 981 var->transp.length = 0; 982 var->nonstd = 0; 983 break; 984 case 24: 985 var->red.offset = 16; 986 var->red.length = 8; 987 var->green.offset = 8; 988 var->green.length = 8; 989 var->blue.offset = 0; 990 var->blue.length = 8; 991 var->nonstd = 0; 992 break; 993 case 32: 994 var->transp.offset = 24; 995 var->transp.length = 8; 996 var->red.offset = 16; 997 var->red.length = 8; 998 var->green.offset = 8; 999 var->green.length = 8; 1000 var->blue.offset = 0; 1001 var->blue.length = 8; 1002 var->nonstd = 0; 1003 break; 1004 default: 1005 err = -EINVAL; 1006 } 1007 1008 var->red.msb_right = 0; 1009 var->green.msb_right = 0; 1010 var->blue.msb_right = 0; 1011 var->transp.msb_right = 0; 1012 1013 if (line_size * var->yres_virtual > par->vram_size) 1014 var->yres_virtual = par->vram_size / line_size; 1015 1016 if (var->yres > var->yres_virtual) 1017 var->yres = var->yres_virtual; 1018 1019 if (var->xres > var->xres_virtual) 1020 var->xres = var->xres_virtual; 1021 1022 if (var->xres + var->xoffset > var->xres_virtual) 1023 var->xoffset = var->xres_virtual - var->xres; 1024 if (var->yres + var->yoffset > var->yres_virtual) 1025 var->yoffset = var->yres_virtual - var->yres; 1026 1027 var->pixclock = da8xx_fb_round_clk(par, var->pixclock); 1028 1029 return err; 1030 } 1031 1032 #ifdef CONFIG_CPU_FREQ 1033 static int lcd_da8xx_cpufreq_transition(struct notifier_block *nb, 1034 unsigned long val, void *data) 1035 { 1036 struct da8xx_fb_par *par; 1037 1038 par = container_of(nb, struct da8xx_fb_par, freq_transition); 1039 if (val == CPUFREQ_POSTCHANGE) { 1040 if (par->lcdc_clk_rate != clk_get_rate(par->lcdc_clk)) { 1041 par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk); 1042 lcd_disable_raster(DA8XX_FRAME_WAIT); 1043 da8xx_fb_calc_config_clk_divider(par, &par->mode); 1044 if (par->blank == FB_BLANK_UNBLANK) 1045 lcd_enable_raster(); 1046 } 1047 } 1048 1049 return 0; 1050 } 1051 1052 static int lcd_da8xx_cpufreq_register(struct da8xx_fb_par *par) 1053 { 1054 par->freq_transition.notifier_call = lcd_da8xx_cpufreq_transition; 1055 1056 return cpufreq_register_notifier(&par->freq_transition, 1057 CPUFREQ_TRANSITION_NOTIFIER); 1058 } 1059 1060 static void lcd_da8xx_cpufreq_deregister(struct da8xx_fb_par *par) 1061 { 1062 cpufreq_unregister_notifier(&par->freq_transition, 1063 CPUFREQ_TRANSITION_NOTIFIER); 1064 } 1065 #endif 1066 1067 static void fb_remove(struct platform_device *dev) 1068 { 1069 struct fb_info *info = platform_get_drvdata(dev); 1070 struct da8xx_fb_par *par = info->par; 1071 int ret; 1072 1073 #ifdef CONFIG_CPU_FREQ 1074 lcd_da8xx_cpufreq_deregister(par); 1075 #endif 1076 if (par->lcd_supply) { 1077 ret = regulator_disable(par->lcd_supply); 1078 if (ret) 1079 dev_warn(&dev->dev, "Failed to disable regulator (%pe)\n", 1080 ERR_PTR(ret)); 1081 } 1082 1083 lcd_disable_raster(DA8XX_FRAME_WAIT); 1084 lcdc_write(0, LCD_RASTER_CTRL_REG); 1085 1086 /* disable DMA */ 1087 lcdc_write(0, LCD_DMA_CTRL_REG); 1088 1089 unregister_framebuffer(info); 1090 fb_dealloc_cmap(&info->cmap); 1091 pm_runtime_put_sync(&dev->dev); 1092 pm_runtime_disable(&dev->dev); 1093 framebuffer_release(info); 1094 } 1095 1096 /* 1097 * Function to wait for vertical sync which for this LCD peripheral 1098 * translates into waiting for the current raster frame to complete. 1099 */ 1100 static int fb_wait_for_vsync(struct fb_info *info) 1101 { 1102 struct da8xx_fb_par *par = info->par; 1103 int ret; 1104 1105 /* 1106 * Set flag to 0 and wait for isr to set to 1. It would seem there is a 1107 * race condition here where the ISR could have occurred just before or 1108 * just after this set. But since we are just coarsely waiting for 1109 * a frame to complete then that's OK. i.e. if the frame completed 1110 * just before this code executed then we have to wait another full 1111 * frame time but there is no way to avoid such a situation. On the 1112 * other hand if the frame completed just after then we don't need 1113 * to wait long at all. Either way we are guaranteed to return to the 1114 * user immediately after a frame completion which is all that is 1115 * required. 1116 */ 1117 par->vsync_flag = 0; 1118 ret = wait_event_interruptible_timeout(par->vsync_wait, 1119 par->vsync_flag != 0, 1120 par->vsync_timeout); 1121 if (ret < 0) 1122 return ret; 1123 if (ret == 0) 1124 return -ETIMEDOUT; 1125 1126 return 0; 1127 } 1128 1129 static int fb_ioctl(struct fb_info *info, unsigned int cmd, 1130 unsigned long arg) 1131 { 1132 struct lcd_sync_arg sync_arg; 1133 1134 switch (cmd) { 1135 case FBIOGET_CONTRAST: 1136 case FBIOPUT_CONTRAST: 1137 case FBIGET_BRIGHTNESS: 1138 case FBIPUT_BRIGHTNESS: 1139 case FBIGET_COLOR: 1140 case FBIPUT_COLOR: 1141 return -ENOTTY; 1142 case FBIPUT_HSYNC: 1143 if (copy_from_user(&sync_arg, (char *)arg, 1144 sizeof(struct lcd_sync_arg))) 1145 return -EFAULT; 1146 lcd_cfg_horizontal_sync(sync_arg.back_porch, 1147 sync_arg.pulse_width, 1148 sync_arg.front_porch); 1149 break; 1150 case FBIPUT_VSYNC: 1151 if (copy_from_user(&sync_arg, (char *)arg, 1152 sizeof(struct lcd_sync_arg))) 1153 return -EFAULT; 1154 lcd_cfg_vertical_sync(sync_arg.back_porch, 1155 sync_arg.pulse_width, 1156 sync_arg.front_porch); 1157 break; 1158 case FBIO_WAITFORVSYNC: 1159 return fb_wait_for_vsync(info); 1160 default: 1161 return -EINVAL; 1162 } 1163 return 0; 1164 } 1165 1166 static int cfb_blank(int blank, struct fb_info *info) 1167 { 1168 struct da8xx_fb_par *par = info->par; 1169 int ret = 0; 1170 1171 if (par->blank == blank) 1172 return 0; 1173 1174 par->blank = blank; 1175 switch (blank) { 1176 case FB_BLANK_UNBLANK: 1177 lcd_enable_raster(); 1178 1179 if (par->lcd_supply) { 1180 ret = regulator_enable(par->lcd_supply); 1181 if (ret) 1182 return ret; 1183 } 1184 break; 1185 case FB_BLANK_NORMAL: 1186 case FB_BLANK_VSYNC_SUSPEND: 1187 case FB_BLANK_HSYNC_SUSPEND: 1188 case FB_BLANK_POWERDOWN: 1189 if (par->lcd_supply) { 1190 ret = regulator_disable(par->lcd_supply); 1191 if (ret) 1192 return ret; 1193 } 1194 1195 lcd_disable_raster(DA8XX_FRAME_WAIT); 1196 break; 1197 default: 1198 ret = -EINVAL; 1199 } 1200 1201 return ret; 1202 } 1203 1204 /* 1205 * Set new x,y offsets in the virtual display for the visible area and switch 1206 * to the new mode. 1207 */ 1208 static int da8xx_pan_display(struct fb_var_screeninfo *var, 1209 struct fb_info *fbi) 1210 { 1211 int ret = 0; 1212 struct fb_var_screeninfo new_var; 1213 struct da8xx_fb_par *par = fbi->par; 1214 struct fb_fix_screeninfo *fix = &fbi->fix; 1215 unsigned int end; 1216 unsigned int start; 1217 unsigned long irq_flags; 1218 1219 if (var->xoffset != fbi->var.xoffset || 1220 var->yoffset != fbi->var.yoffset) { 1221 memcpy(&new_var, &fbi->var, sizeof(new_var)); 1222 new_var.xoffset = var->xoffset; 1223 new_var.yoffset = var->yoffset; 1224 if (fb_check_var(&new_var, fbi)) 1225 ret = -EINVAL; 1226 else { 1227 memcpy(&fbi->var, &new_var, sizeof(new_var)); 1228 1229 start = fix->smem_start + 1230 new_var.yoffset * fix->line_length + 1231 new_var.xoffset * fbi->var.bits_per_pixel / 8; 1232 end = start + fbi->var.yres * fix->line_length - 1; 1233 par->dma_start = start; 1234 par->dma_end = end; 1235 spin_lock_irqsave(&par->lock_for_chan_update, 1236 irq_flags); 1237 if (par->which_dma_channel_done == 0) { 1238 lcdc_write(par->dma_start, 1239 LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 1240 lcdc_write(par->dma_end, 1241 LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 1242 } else if (par->which_dma_channel_done == 1) { 1243 lcdc_write(par->dma_start, 1244 LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 1245 lcdc_write(par->dma_end, 1246 LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 1247 } 1248 spin_unlock_irqrestore(&par->lock_for_chan_update, 1249 irq_flags); 1250 } 1251 } 1252 1253 return ret; 1254 } 1255 1256 static int da8xxfb_set_par(struct fb_info *info) 1257 { 1258 struct da8xx_fb_par *par = info->par; 1259 int ret; 1260 bool raster = da8xx_fb_is_raster_enabled(); 1261 1262 if (raster) 1263 lcd_disable_raster(DA8XX_FRAME_WAIT); 1264 1265 fb_var_to_videomode(&par->mode, &info->var); 1266 1267 par->cfg.bpp = info->var.bits_per_pixel; 1268 1269 info->fix.visual = (par->cfg.bpp <= 8) ? 1270 FB_VISUAL_PSEUDOCOLOR : FB_VISUAL_TRUECOLOR; 1271 info->fix.line_length = (par->mode.xres * par->cfg.bpp) / 8; 1272 1273 ret = lcd_init(par, &par->cfg, &par->mode); 1274 if (ret < 0) { 1275 dev_err(par->dev, "lcd init failed\n"); 1276 return ret; 1277 } 1278 1279 par->dma_start = info->fix.smem_start + 1280 info->var.yoffset * info->fix.line_length + 1281 info->var.xoffset * info->var.bits_per_pixel / 8; 1282 par->dma_end = par->dma_start + 1283 info->var.yres * info->fix.line_length - 1; 1284 1285 lcdc_write(par->dma_start, LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 1286 lcdc_write(par->dma_end, LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 1287 lcdc_write(par->dma_start, LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 1288 lcdc_write(par->dma_end, LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 1289 1290 if (raster) 1291 lcd_enable_raster(); 1292 1293 return 0; 1294 } 1295 1296 static const struct fb_ops da8xx_fb_ops = { 1297 .owner = THIS_MODULE, 1298 .fb_check_var = fb_check_var, 1299 .fb_set_par = da8xxfb_set_par, 1300 .fb_setcolreg = fb_setcolreg, 1301 .fb_pan_display = da8xx_pan_display, 1302 .fb_ioctl = fb_ioctl, 1303 .fb_fillrect = cfb_fillrect, 1304 .fb_copyarea = cfb_copyarea, 1305 .fb_imageblit = cfb_imageblit, 1306 .fb_blank = cfb_blank, 1307 }; 1308 1309 static struct fb_videomode *da8xx_fb_get_videomode(struct platform_device *dev) 1310 { 1311 struct da8xx_lcdc_platform_data *fb_pdata = dev_get_platdata(&dev->dev); 1312 struct fb_videomode *lcdc_info; 1313 int i; 1314 1315 for (i = 0, lcdc_info = known_lcd_panels; 1316 i < ARRAY_SIZE(known_lcd_panels); i++, lcdc_info++) { 1317 if (strcmp(fb_pdata->type, lcdc_info->name) == 0) 1318 break; 1319 } 1320 1321 if (i == ARRAY_SIZE(known_lcd_panels)) { 1322 dev_err(&dev->dev, "no panel found\n"); 1323 return NULL; 1324 } 1325 dev_info(&dev->dev, "found %s panel\n", lcdc_info->name); 1326 1327 return lcdc_info; 1328 } 1329 1330 static int fb_probe(struct platform_device *device) 1331 { 1332 struct da8xx_lcdc_platform_data *fb_pdata = 1333 dev_get_platdata(&device->dev); 1334 struct lcd_ctrl_config *lcd_cfg; 1335 struct fb_videomode *lcdc_info; 1336 struct fb_info *da8xx_fb_info; 1337 struct da8xx_fb_par *par; 1338 struct clk *tmp_lcdc_clk; 1339 int ret; 1340 unsigned long ulcm; 1341 1342 if (fb_pdata == NULL) { 1343 dev_err(&device->dev, "Can not get platform data\n"); 1344 return -ENOENT; 1345 } 1346 1347 lcdc_info = da8xx_fb_get_videomode(device); 1348 if (lcdc_info == NULL) 1349 return -ENODEV; 1350 1351 da8xx_fb_reg_base = devm_platform_ioremap_resource(device, 0); 1352 if (IS_ERR(da8xx_fb_reg_base)) 1353 return PTR_ERR(da8xx_fb_reg_base); 1354 1355 tmp_lcdc_clk = devm_clk_get(&device->dev, "fck"); 1356 if (IS_ERR(tmp_lcdc_clk)) 1357 return dev_err_probe(&device->dev, PTR_ERR(tmp_lcdc_clk), 1358 "Can not get device clock\n"); 1359 1360 pm_runtime_enable(&device->dev); 1361 pm_runtime_get_sync(&device->dev); 1362 1363 /* Determine LCD IP Version */ 1364 switch (lcdc_read(LCD_PID_REG)) { 1365 case 0x4C100102: 1366 lcd_revision = LCD_VERSION_1; 1367 break; 1368 case 0x4F200800: 1369 case 0x4F201000: 1370 lcd_revision = LCD_VERSION_2; 1371 break; 1372 default: 1373 dev_warn(&device->dev, "Unknown PID Reg value 0x%x, " 1374 "defaulting to LCD revision 1\n", 1375 lcdc_read(LCD_PID_REG)); 1376 lcd_revision = LCD_VERSION_1; 1377 break; 1378 } 1379 1380 lcd_cfg = (struct lcd_ctrl_config *)fb_pdata->controller_data; 1381 1382 if (!lcd_cfg) { 1383 ret = -EINVAL; 1384 goto err_pm_runtime_disable; 1385 } 1386 1387 da8xx_fb_info = framebuffer_alloc(sizeof(struct da8xx_fb_par), 1388 &device->dev); 1389 if (!da8xx_fb_info) { 1390 ret = -ENOMEM; 1391 goto err_pm_runtime_disable; 1392 } 1393 1394 par = da8xx_fb_info->par; 1395 par->dev = &device->dev; 1396 par->lcdc_clk = tmp_lcdc_clk; 1397 par->lcdc_clk_rate = clk_get_rate(par->lcdc_clk); 1398 1399 par->lcd_supply = devm_regulator_get_optional(&device->dev, "lcd"); 1400 if (IS_ERR(par->lcd_supply)) { 1401 if (PTR_ERR(par->lcd_supply) == -EPROBE_DEFER) { 1402 ret = -EPROBE_DEFER; 1403 goto err_release_fb; 1404 } 1405 1406 par->lcd_supply = NULL; 1407 } else { 1408 ret = regulator_enable(par->lcd_supply); 1409 if (ret) 1410 goto err_release_fb; 1411 } 1412 1413 fb_videomode_to_var(&da8xx_fb_var, lcdc_info); 1414 par->cfg = *lcd_cfg; 1415 1416 da8xx_fb_lcd_reset(); 1417 1418 /* allocate frame buffer */ 1419 par->vram_size = lcdc_info->xres * lcdc_info->yres * lcd_cfg->bpp; 1420 ulcm = lcm((lcdc_info->xres * lcd_cfg->bpp)/8, PAGE_SIZE); 1421 par->vram_size = roundup(par->vram_size/8, ulcm); 1422 par->vram_size = par->vram_size * LCD_NUM_BUFFERS; 1423 1424 par->vram_virt = dmam_alloc_coherent(par->dev, 1425 par->vram_size, 1426 &par->vram_phys, 1427 GFP_KERNEL | GFP_DMA); 1428 if (!par->vram_virt) { 1429 dev_err(&device->dev, 1430 "GLCD: kmalloc for frame buffer failed\n"); 1431 ret = -EINVAL; 1432 goto err_disable_reg; 1433 } 1434 1435 da8xx_fb_info->screen_base = (char __iomem *) par->vram_virt; 1436 da8xx_fb_fix.smem_start = par->vram_phys; 1437 da8xx_fb_fix.smem_len = par->vram_size; 1438 da8xx_fb_fix.line_length = (lcdc_info->xres * lcd_cfg->bpp) / 8; 1439 1440 par->dma_start = par->vram_phys; 1441 par->dma_end = par->dma_start + lcdc_info->yres * 1442 da8xx_fb_fix.line_length - 1; 1443 1444 /* allocate palette buffer */ 1445 par->v_palette_base = dmam_alloc_coherent(par->dev, PALETTE_SIZE, 1446 &par->p_palette_base, 1447 GFP_KERNEL | GFP_DMA); 1448 if (!par->v_palette_base) { 1449 dev_err(&device->dev, 1450 "GLCD: kmalloc for palette buffer failed\n"); 1451 ret = -EINVAL; 1452 goto err_release_fb; 1453 } 1454 1455 par->irq = platform_get_irq(device, 0); 1456 if (par->irq < 0) { 1457 ret = -ENOENT; 1458 goto err_release_fb; 1459 } 1460 1461 da8xx_fb_var.grayscale = 1462 lcd_cfg->panel_shade == MONOCHROME ? 1 : 0; 1463 da8xx_fb_var.bits_per_pixel = lcd_cfg->bpp; 1464 1465 /* Initialize fbinfo */ 1466 da8xx_fb_info->fix = da8xx_fb_fix; 1467 da8xx_fb_info->var = da8xx_fb_var; 1468 da8xx_fb_info->fbops = &da8xx_fb_ops; 1469 da8xx_fb_info->pseudo_palette = par->pseudo_palette; 1470 da8xx_fb_info->fix.visual = (da8xx_fb_info->var.bits_per_pixel <= 8) ? 1471 FB_VISUAL_PSEUDOCOLOR : FB_VISUAL_TRUECOLOR; 1472 1473 ret = fb_alloc_cmap(&da8xx_fb_info->cmap, PALETTE_SIZE, 0); 1474 if (ret) 1475 goto err_disable_reg; 1476 da8xx_fb_info->cmap.len = par->palette_sz; 1477 1478 /* initialize var_screeninfo */ 1479 da8xx_fb_var.activate = FB_ACTIVATE_FORCE; 1480 fb_set_var(da8xx_fb_info, &da8xx_fb_var); 1481 1482 platform_set_drvdata(device, da8xx_fb_info); 1483 1484 /* initialize the vsync wait queue */ 1485 init_waitqueue_head(&par->vsync_wait); 1486 par->vsync_timeout = HZ / 5; 1487 par->which_dma_channel_done = -1; 1488 spin_lock_init(&par->lock_for_chan_update); 1489 1490 /* Register the Frame Buffer */ 1491 if (register_framebuffer(da8xx_fb_info) < 0) { 1492 dev_err(&device->dev, 1493 "GLCD: Frame Buffer Registration Failed!\n"); 1494 ret = -EINVAL; 1495 goto err_dealloc_cmap; 1496 } 1497 1498 #ifdef CONFIG_CPU_FREQ 1499 ret = lcd_da8xx_cpufreq_register(par); 1500 if (ret) { 1501 dev_err(&device->dev, "failed to register cpufreq\n"); 1502 goto err_cpu_freq; 1503 } 1504 #endif 1505 1506 if (lcd_revision == LCD_VERSION_1) 1507 lcdc_irq_handler = lcdc_irq_handler_rev01; 1508 else { 1509 init_waitqueue_head(&frame_done_wq); 1510 lcdc_irq_handler = lcdc_irq_handler_rev02; 1511 } 1512 1513 ret = devm_request_irq(&device->dev, par->irq, lcdc_irq_handler, 0, 1514 DRIVER_NAME, par); 1515 if (ret) 1516 goto irq_freq; 1517 return 0; 1518 1519 irq_freq: 1520 #ifdef CONFIG_CPU_FREQ 1521 lcd_da8xx_cpufreq_deregister(par); 1522 err_cpu_freq: 1523 #endif 1524 unregister_framebuffer(da8xx_fb_info); 1525 1526 err_dealloc_cmap: 1527 fb_dealloc_cmap(&da8xx_fb_info->cmap); 1528 1529 err_disable_reg: 1530 if (par->lcd_supply) 1531 regulator_disable(par->lcd_supply); 1532 err_release_fb: 1533 framebuffer_release(da8xx_fb_info); 1534 1535 err_pm_runtime_disable: 1536 pm_runtime_put_sync(&device->dev); 1537 pm_runtime_disable(&device->dev); 1538 1539 return ret; 1540 } 1541 1542 #ifdef CONFIG_PM_SLEEP 1543 static struct lcdc_context { 1544 u32 clk_enable; 1545 u32 ctrl; 1546 u32 dma_ctrl; 1547 u32 raster_timing_0; 1548 u32 raster_timing_1; 1549 u32 raster_timing_2; 1550 u32 int_enable_set; 1551 u32 dma_frm_buf_base_addr_0; 1552 u32 dma_frm_buf_ceiling_addr_0; 1553 u32 dma_frm_buf_base_addr_1; 1554 u32 dma_frm_buf_ceiling_addr_1; 1555 u32 raster_ctrl; 1556 } reg_context; 1557 1558 static void lcd_context_save(void) 1559 { 1560 if (lcd_revision == LCD_VERSION_2) { 1561 reg_context.clk_enable = lcdc_read(LCD_CLK_ENABLE_REG); 1562 reg_context.int_enable_set = lcdc_read(LCD_INT_ENABLE_SET_REG); 1563 } 1564 1565 reg_context.ctrl = lcdc_read(LCD_CTRL_REG); 1566 reg_context.dma_ctrl = lcdc_read(LCD_DMA_CTRL_REG); 1567 reg_context.raster_timing_0 = lcdc_read(LCD_RASTER_TIMING_0_REG); 1568 reg_context.raster_timing_1 = lcdc_read(LCD_RASTER_TIMING_1_REG); 1569 reg_context.raster_timing_2 = lcdc_read(LCD_RASTER_TIMING_2_REG); 1570 reg_context.dma_frm_buf_base_addr_0 = 1571 lcdc_read(LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 1572 reg_context.dma_frm_buf_ceiling_addr_0 = 1573 lcdc_read(LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 1574 reg_context.dma_frm_buf_base_addr_1 = 1575 lcdc_read(LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 1576 reg_context.dma_frm_buf_ceiling_addr_1 = 1577 lcdc_read(LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 1578 reg_context.raster_ctrl = lcdc_read(LCD_RASTER_CTRL_REG); 1579 return; 1580 } 1581 1582 static void lcd_context_restore(void) 1583 { 1584 if (lcd_revision == LCD_VERSION_2) { 1585 lcdc_write(reg_context.clk_enable, LCD_CLK_ENABLE_REG); 1586 lcdc_write(reg_context.int_enable_set, LCD_INT_ENABLE_SET_REG); 1587 } 1588 1589 lcdc_write(reg_context.ctrl, LCD_CTRL_REG); 1590 lcdc_write(reg_context.dma_ctrl, LCD_DMA_CTRL_REG); 1591 lcdc_write(reg_context.raster_timing_0, LCD_RASTER_TIMING_0_REG); 1592 lcdc_write(reg_context.raster_timing_1, LCD_RASTER_TIMING_1_REG); 1593 lcdc_write(reg_context.raster_timing_2, LCD_RASTER_TIMING_2_REG); 1594 lcdc_write(reg_context.dma_frm_buf_base_addr_0, 1595 LCD_DMA_FRM_BUF_BASE_ADDR_0_REG); 1596 lcdc_write(reg_context.dma_frm_buf_ceiling_addr_0, 1597 LCD_DMA_FRM_BUF_CEILING_ADDR_0_REG); 1598 lcdc_write(reg_context.dma_frm_buf_base_addr_1, 1599 LCD_DMA_FRM_BUF_BASE_ADDR_1_REG); 1600 lcdc_write(reg_context.dma_frm_buf_ceiling_addr_1, 1601 LCD_DMA_FRM_BUF_CEILING_ADDR_1_REG); 1602 lcdc_write(reg_context.raster_ctrl, LCD_RASTER_CTRL_REG); 1603 return; 1604 } 1605 1606 static int fb_suspend(struct device *dev) 1607 { 1608 struct fb_info *info = dev_get_drvdata(dev); 1609 struct da8xx_fb_par *par = info->par; 1610 int ret; 1611 1612 console_lock(); 1613 if (par->lcd_supply) { 1614 ret = regulator_disable(par->lcd_supply); 1615 if (ret) 1616 return ret; 1617 } 1618 1619 fb_set_suspend(info, 1); 1620 lcd_disable_raster(DA8XX_FRAME_WAIT); 1621 lcd_context_save(); 1622 pm_runtime_put_sync(dev); 1623 console_unlock(); 1624 1625 return 0; 1626 } 1627 static int fb_resume(struct device *dev) 1628 { 1629 struct fb_info *info = dev_get_drvdata(dev); 1630 struct da8xx_fb_par *par = info->par; 1631 int ret; 1632 1633 console_lock(); 1634 pm_runtime_get_sync(dev); 1635 lcd_context_restore(); 1636 if (par->blank == FB_BLANK_UNBLANK) { 1637 lcd_enable_raster(); 1638 1639 if (par->lcd_supply) { 1640 ret = regulator_enable(par->lcd_supply); 1641 if (ret) 1642 return ret; 1643 } 1644 } 1645 1646 fb_set_suspend(info, 0); 1647 console_unlock(); 1648 1649 return 0; 1650 } 1651 #endif 1652 1653 static SIMPLE_DEV_PM_OPS(fb_pm_ops, fb_suspend, fb_resume); 1654 1655 static struct platform_driver da8xx_fb_driver = { 1656 .probe = fb_probe, 1657 .remove_new = fb_remove, 1658 .driver = { 1659 .name = DRIVER_NAME, 1660 .pm = &fb_pm_ops, 1661 }, 1662 }; 1663 module_platform_driver(da8xx_fb_driver); 1664 1665 MODULE_DESCRIPTION("Framebuffer driver for TI da8xx/omap-l1xx"); 1666 MODULE_AUTHOR("Texas Instruments"); 1667 MODULE_LICENSE("GPL"); 1668