1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * mxuport.c - MOXA UPort series driver 4 * 5 * Copyright (c) 2006 Moxa Technologies Co., Ltd. 6 * Copyright (c) 2013 Andrew Lunn <andrew@lunn.ch> 7 * 8 * Supports the following Moxa USB to serial converters: 9 * 2 ports : UPort 1250, UPort 1250I 10 * 4 ports : UPort 1410, UPort 1450, UPort 1450I 11 * 8 ports : UPort 1610-8, UPort 1650-8 12 * 16 ports : UPort 1610-16, UPort 1650-16 13 */ 14 15 #include <linux/kernel.h> 16 #include <linux/module.h> 17 #include <linux/firmware.h> 18 #include <linux/jiffies.h> 19 #include <linux/serial.h> 20 #include <linux/serial_reg.h> 21 #include <linux/slab.h> 22 #include <linux/tty.h> 23 #include <linux/tty_driver.h> 24 #include <linux/tty_flip.h> 25 #include <linux/uaccess.h> 26 #include <linux/usb.h> 27 #include <linux/usb/serial.h> 28 #include <asm/unaligned.h> 29 30 /* Definitions for the vendor ID and device ID */ 31 #define MX_USBSERIAL_VID 0x110A 32 #define MX_UPORT1250_PID 0x1250 33 #define MX_UPORT1251_PID 0x1251 34 #define MX_UPORT1410_PID 0x1410 35 #define MX_UPORT1450_PID 0x1450 36 #define MX_UPORT1451_PID 0x1451 37 #define MX_UPORT1618_PID 0x1618 38 #define MX_UPORT1658_PID 0x1658 39 #define MX_UPORT1613_PID 0x1613 40 #define MX_UPORT1653_PID 0x1653 41 42 /* Definitions for USB info */ 43 #define HEADER_SIZE 4 44 #define EVENT_LENGTH 8 45 #define DOWN_BLOCK_SIZE 64 46 47 /* Definitions for firmware info */ 48 #define VER_ADDR_1 0x20 49 #define VER_ADDR_2 0x24 50 #define VER_ADDR_3 0x28 51 52 /* Definitions for USB vendor request */ 53 #define RQ_VENDOR_NONE 0x00 54 #define RQ_VENDOR_SET_BAUD 0x01 /* Set baud rate */ 55 #define RQ_VENDOR_SET_LINE 0x02 /* Set line status */ 56 #define RQ_VENDOR_SET_CHARS 0x03 /* Set Xon/Xoff chars */ 57 #define RQ_VENDOR_SET_RTS 0x04 /* Set RTS */ 58 #define RQ_VENDOR_SET_DTR 0x05 /* Set DTR */ 59 #define RQ_VENDOR_SET_XONXOFF 0x06 /* Set auto Xon/Xoff */ 60 #define RQ_VENDOR_SET_RX_HOST_EN 0x07 /* Set RX host enable */ 61 #define RQ_VENDOR_SET_OPEN 0x08 /* Set open/close port */ 62 #define RQ_VENDOR_PURGE 0x09 /* Purge Rx/Tx buffer */ 63 #define RQ_VENDOR_SET_MCR 0x0A /* Set MCR register */ 64 #define RQ_VENDOR_SET_BREAK 0x0B /* Set Break signal */ 65 66 #define RQ_VENDOR_START_FW_DOWN 0x0C /* Start firmware download */ 67 #define RQ_VENDOR_STOP_FW_DOWN 0x0D /* Stop firmware download */ 68 #define RQ_VENDOR_QUERY_FW_READY 0x0E /* Query if new firmware ready */ 69 70 #define RQ_VENDOR_SET_FIFO_DISABLE 0x0F /* Set fifo disable */ 71 #define RQ_VENDOR_SET_INTERFACE 0x10 /* Set interface */ 72 #define RQ_VENDOR_SET_HIGH_PERFOR 0x11 /* Set hi-performance */ 73 74 #define RQ_VENDOR_ERASE_BLOCK 0x12 /* Erase flash block */ 75 #define RQ_VENDOR_WRITE_PAGE 0x13 /* Write flash page */ 76 #define RQ_VENDOR_PREPARE_WRITE 0x14 /* Prepare write flash */ 77 #define RQ_VENDOR_CONFIRM_WRITE 0x15 /* Confirm write flash */ 78 #define RQ_VENDOR_LOCATE 0x16 /* Locate the device */ 79 80 #define RQ_VENDOR_START_ROM_DOWN 0x17 /* Start firmware download */ 81 #define RQ_VENDOR_ROM_DATA 0x18 /* Rom file data */ 82 #define RQ_VENDOR_STOP_ROM_DOWN 0x19 /* Stop firmware download */ 83 #define RQ_VENDOR_FW_DATA 0x20 /* Firmware data */ 84 85 #define RQ_VENDOR_RESET_DEVICE 0x23 /* Try to reset the device */ 86 #define RQ_VENDOR_QUERY_FW_CONFIG 0x24 87 88 #define RQ_VENDOR_GET_VERSION 0x81 /* Get firmware version */ 89 #define RQ_VENDOR_GET_PAGE 0x82 /* Read flash page */ 90 #define RQ_VENDOR_GET_ROM_PROC 0x83 /* Get ROM process state */ 91 92 #define RQ_VENDOR_GET_INQUEUE 0x84 /* Data in input buffer */ 93 #define RQ_VENDOR_GET_OUTQUEUE 0x85 /* Data in output buffer */ 94 95 #define RQ_VENDOR_GET_MSR 0x86 /* Get modem status register */ 96 97 /* Definitions for UPort event type */ 98 #define UPORT_EVENT_NONE 0 /* None */ 99 #define UPORT_EVENT_TXBUF_THRESHOLD 1 /* Tx buffer threshold */ 100 #define UPORT_EVENT_SEND_NEXT 2 /* Send next */ 101 #define UPORT_EVENT_MSR 3 /* Modem status */ 102 #define UPORT_EVENT_LSR 4 /* Line status */ 103 #define UPORT_EVENT_MCR 5 /* Modem control */ 104 105 /* Definitions for serial event type */ 106 #define SERIAL_EV_CTS 0x0008 /* CTS changed state */ 107 #define SERIAL_EV_DSR 0x0010 /* DSR changed state */ 108 #define SERIAL_EV_RLSD 0x0020 /* RLSD changed state */ 109 110 /* Definitions for modem control event type */ 111 #define SERIAL_EV_XOFF 0x40 /* XOFF received */ 112 113 /* Definitions for line control of communication */ 114 #define MX_WORDLENGTH_5 5 115 #define MX_WORDLENGTH_6 6 116 #define MX_WORDLENGTH_7 7 117 #define MX_WORDLENGTH_8 8 118 119 #define MX_PARITY_NONE 0 120 #define MX_PARITY_ODD 1 121 #define MX_PARITY_EVEN 2 122 #define MX_PARITY_MARK 3 123 #define MX_PARITY_SPACE 4 124 125 #define MX_STOP_BITS_1 0 126 #define MX_STOP_BITS_1_5 1 127 #define MX_STOP_BITS_2 2 128 129 #define MX_RTS_DISABLE 0x0 130 #define MX_RTS_ENABLE 0x1 131 #define MX_RTS_HW 0x2 132 #define MX_RTS_NO_CHANGE 0x3 /* Flag, not valid register value*/ 133 134 #define MX_INT_RS232 0 135 #define MX_INT_2W_RS485 1 136 #define MX_INT_RS422 2 137 #define MX_INT_4W_RS485 3 138 139 /* Definitions for holding reason */ 140 #define MX_WAIT_FOR_CTS 0x0001 141 #define MX_WAIT_FOR_DSR 0x0002 142 #define MX_WAIT_FOR_DCD 0x0004 143 #define MX_WAIT_FOR_XON 0x0008 144 #define MX_WAIT_FOR_START_TX 0x0010 145 #define MX_WAIT_FOR_UNTHROTTLE 0x0020 146 #define MX_WAIT_FOR_LOW_WATER 0x0040 147 #define MX_WAIT_FOR_SEND_NEXT 0x0080 148 149 #define MX_UPORT_2_PORT BIT(0) 150 #define MX_UPORT_4_PORT BIT(1) 151 #define MX_UPORT_8_PORT BIT(2) 152 #define MX_UPORT_16_PORT BIT(3) 153 154 /* This structure holds all of the local port information */ 155 struct mxuport_port { 156 u8 mcr_state; /* Last MCR state */ 157 u8 msr_state; /* Last MSR state */ 158 struct mutex mutex; /* Protects mcr_state */ 159 spinlock_t spinlock; /* Protects msr_state */ 160 }; 161 162 /* Table of devices that work with this driver */ 163 static const struct usb_device_id mxuport_idtable[] = { 164 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1250_PID), 165 .driver_info = MX_UPORT_2_PORT }, 166 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1251_PID), 167 .driver_info = MX_UPORT_2_PORT }, 168 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1410_PID), 169 .driver_info = MX_UPORT_4_PORT }, 170 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1450_PID), 171 .driver_info = MX_UPORT_4_PORT }, 172 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1451_PID), 173 .driver_info = MX_UPORT_4_PORT }, 174 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1618_PID), 175 .driver_info = MX_UPORT_8_PORT }, 176 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1658_PID), 177 .driver_info = MX_UPORT_8_PORT }, 178 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1613_PID), 179 .driver_info = MX_UPORT_16_PORT }, 180 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1653_PID), 181 .driver_info = MX_UPORT_16_PORT }, 182 {} /* Terminating entry */ 183 }; 184 185 MODULE_DEVICE_TABLE(usb, mxuport_idtable); 186 187 /* 188 * Add a four byte header containing the port number and the number of 189 * bytes of data in the message. Return the number of bytes in the 190 * buffer. 191 */ 192 static int mxuport_prepare_write_buffer(struct usb_serial_port *port, 193 void *dest, size_t size) 194 { 195 u8 *buf = dest; 196 int count; 197 198 count = kfifo_out_locked(&port->write_fifo, buf + HEADER_SIZE, 199 size - HEADER_SIZE, 200 &port->lock); 201 202 put_unaligned_be16(port->port_number, buf); 203 put_unaligned_be16(count, buf + 2); 204 205 dev_dbg(&port->dev, "%s - size %zd count %d\n", __func__, 206 size, count); 207 208 return count + HEADER_SIZE; 209 } 210 211 /* Read the given buffer in from the control pipe. */ 212 static int mxuport_recv_ctrl_urb(struct usb_serial *serial, 213 u8 request, u16 value, u16 index, 214 u8 *data, size_t size) 215 { 216 int status; 217 218 status = usb_control_msg(serial->dev, 219 usb_rcvctrlpipe(serial->dev, 0), 220 request, 221 (USB_DIR_IN | USB_TYPE_VENDOR | 222 USB_RECIP_DEVICE), value, index, 223 data, size, 224 USB_CTRL_GET_TIMEOUT); 225 if (status < 0) { 226 dev_err(&serial->interface->dev, 227 "%s - usb_control_msg failed (%d)\n", 228 __func__, status); 229 return status; 230 } 231 232 if (status != size) { 233 dev_err(&serial->interface->dev, 234 "%s - short read (%d / %zd)\n", 235 __func__, status, size); 236 return -EIO; 237 } 238 239 return status; 240 } 241 242 /* Write the given buffer out to the control pipe. */ 243 static int mxuport_send_ctrl_data_urb(struct usb_serial *serial, 244 u8 request, 245 u16 value, u16 index, 246 u8 *data, size_t size) 247 { 248 int status; 249 250 status = usb_control_msg(serial->dev, 251 usb_sndctrlpipe(serial->dev, 0), 252 request, 253 (USB_DIR_OUT | USB_TYPE_VENDOR | 254 USB_RECIP_DEVICE), value, index, 255 data, size, 256 USB_CTRL_SET_TIMEOUT); 257 if (status < 0) { 258 dev_err(&serial->interface->dev, 259 "%s - usb_control_msg failed (%d)\n", 260 __func__, status); 261 return status; 262 } 263 264 return 0; 265 } 266 267 /* Send a vendor request without any data */ 268 static int mxuport_send_ctrl_urb(struct usb_serial *serial, 269 u8 request, u16 value, u16 index) 270 { 271 return mxuport_send_ctrl_data_urb(serial, request, value, index, 272 NULL, 0); 273 } 274 275 /* 276 * mxuport_throttle - throttle function of driver 277 * 278 * This function is called by the tty driver when it wants to stop the 279 * data being read from the port. Since all the data comes over one 280 * bulk in endpoint, we cannot stop submitting urbs by setting 281 * port->throttle. Instead tell the device to stop sending us data for 282 * the port. 283 */ 284 static void mxuport_throttle(struct tty_struct *tty) 285 { 286 struct usb_serial_port *port = tty->driver_data; 287 struct usb_serial *serial = port->serial; 288 289 dev_dbg(&port->dev, "%s\n", __func__); 290 291 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 292 0, port->port_number); 293 } 294 295 /* 296 * mxuport_unthrottle - unthrottle function of driver 297 * 298 * This function is called by the tty driver when it wants to resume 299 * the data being read from the port. Tell the device it can resume 300 * sending us received data from the port. 301 */ 302 static void mxuport_unthrottle(struct tty_struct *tty) 303 { 304 305 struct usb_serial_port *port = tty->driver_data; 306 struct usb_serial *serial = port->serial; 307 308 dev_dbg(&port->dev, "%s\n", __func__); 309 310 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 311 1, port->port_number); 312 } 313 314 /* 315 * Processes one chunk of data received for a port. Mostly a copy of 316 * usb_serial_generic_process_read_urb(). 317 */ 318 static void mxuport_process_read_urb_data(struct usb_serial_port *port, 319 char *data, int size) 320 { 321 int i; 322 323 if (port->sysrq) { 324 for (i = 0; i < size; i++, data++) { 325 if (!usb_serial_handle_sysrq_char(port, *data)) 326 tty_insert_flip_char(&port->port, *data, 327 TTY_NORMAL); 328 } 329 } else { 330 tty_insert_flip_string(&port->port, data, size); 331 } 332 tty_flip_buffer_push(&port->port); 333 } 334 335 static void mxuport_msr_event(struct usb_serial_port *port, u8 buf[4]) 336 { 337 struct mxuport_port *mxport = usb_get_serial_port_data(port); 338 u8 rcv_msr_hold = buf[2] & 0xF0; 339 u16 rcv_msr_event = get_unaligned_be16(buf); 340 unsigned long flags; 341 342 if (rcv_msr_event == 0) 343 return; 344 345 /* Update MSR status */ 346 spin_lock_irqsave(&mxport->spinlock, flags); 347 348 dev_dbg(&port->dev, "%s - current MSR status = 0x%x\n", 349 __func__, mxport->msr_state); 350 351 if (rcv_msr_hold & UART_MSR_CTS) { 352 mxport->msr_state |= UART_MSR_CTS; 353 dev_dbg(&port->dev, "%s - CTS high\n", __func__); 354 } else { 355 mxport->msr_state &= ~UART_MSR_CTS; 356 dev_dbg(&port->dev, "%s - CTS low\n", __func__); 357 } 358 359 if (rcv_msr_hold & UART_MSR_DSR) { 360 mxport->msr_state |= UART_MSR_DSR; 361 dev_dbg(&port->dev, "%s - DSR high\n", __func__); 362 } else { 363 mxport->msr_state &= ~UART_MSR_DSR; 364 dev_dbg(&port->dev, "%s - DSR low\n", __func__); 365 } 366 367 if (rcv_msr_hold & UART_MSR_DCD) { 368 mxport->msr_state |= UART_MSR_DCD; 369 dev_dbg(&port->dev, "%s - DCD high\n", __func__); 370 } else { 371 mxport->msr_state &= ~UART_MSR_DCD; 372 dev_dbg(&port->dev, "%s - DCD low\n", __func__); 373 } 374 spin_unlock_irqrestore(&mxport->spinlock, flags); 375 376 if (rcv_msr_event & 377 (SERIAL_EV_CTS | SERIAL_EV_DSR | SERIAL_EV_RLSD)) { 378 379 if (rcv_msr_event & SERIAL_EV_CTS) { 380 port->icount.cts++; 381 dev_dbg(&port->dev, "%s - CTS change\n", __func__); 382 } 383 384 if (rcv_msr_event & SERIAL_EV_DSR) { 385 port->icount.dsr++; 386 dev_dbg(&port->dev, "%s - DSR change\n", __func__); 387 } 388 389 if (rcv_msr_event & SERIAL_EV_RLSD) { 390 port->icount.dcd++; 391 dev_dbg(&port->dev, "%s - DCD change\n", __func__); 392 } 393 wake_up_interruptible(&port->port.delta_msr_wait); 394 } 395 } 396 397 static void mxuport_lsr_event(struct usb_serial_port *port, u8 buf[4]) 398 { 399 u8 lsr_event = buf[2]; 400 401 if (lsr_event & UART_LSR_BI) { 402 port->icount.brk++; 403 dev_dbg(&port->dev, "%s - break error\n", __func__); 404 } 405 406 if (lsr_event & UART_LSR_FE) { 407 port->icount.frame++; 408 dev_dbg(&port->dev, "%s - frame error\n", __func__); 409 } 410 411 if (lsr_event & UART_LSR_PE) { 412 port->icount.parity++; 413 dev_dbg(&port->dev, "%s - parity error\n", __func__); 414 } 415 416 if (lsr_event & UART_LSR_OE) { 417 port->icount.overrun++; 418 dev_dbg(&port->dev, "%s - overrun error\n", __func__); 419 } 420 } 421 422 /* 423 * When something interesting happens, modem control lines XON/XOFF 424 * etc, the device sends an event. Process these events. 425 */ 426 static void mxuport_process_read_urb_event(struct usb_serial_port *port, 427 u8 buf[4], u32 event) 428 { 429 dev_dbg(&port->dev, "%s - receive event : %04x\n", __func__, event); 430 431 switch (event) { 432 case UPORT_EVENT_SEND_NEXT: 433 /* 434 * Sent as part of the flow control on device buffers. 435 * Not currently used. 436 */ 437 break; 438 case UPORT_EVENT_MSR: 439 mxuport_msr_event(port, buf); 440 break; 441 case UPORT_EVENT_LSR: 442 mxuport_lsr_event(port, buf); 443 break; 444 case UPORT_EVENT_MCR: 445 /* 446 * Event to indicate a change in XON/XOFF from the 447 * peer. Currently not used. We just continue 448 * sending the device data and it will buffer it if 449 * needed. This event could be used for flow control 450 * between the host and the device. 451 */ 452 break; 453 default: 454 dev_dbg(&port->dev, "Unexpected event\n"); 455 break; 456 } 457 } 458 459 /* 460 * One URB can contain data for multiple ports. Demultiplex the data, 461 * checking the port exists, is opened and the message is valid. 462 */ 463 static void mxuport_process_read_urb_demux_data(struct urb *urb) 464 { 465 struct usb_serial_port *port = urb->context; 466 struct usb_serial *serial = port->serial; 467 u8 *data = urb->transfer_buffer; 468 u8 *end = data + urb->actual_length; 469 struct usb_serial_port *demux_port; 470 u8 *ch; 471 u16 rcv_port; 472 u16 rcv_len; 473 474 while (data < end) { 475 if (data + HEADER_SIZE > end) { 476 dev_warn(&port->dev, "%s - message with short header\n", 477 __func__); 478 return; 479 } 480 481 rcv_port = get_unaligned_be16(data); 482 if (rcv_port >= serial->num_ports) { 483 dev_warn(&port->dev, "%s - message for invalid port\n", 484 __func__); 485 return; 486 } 487 488 demux_port = serial->port[rcv_port]; 489 rcv_len = get_unaligned_be16(data + 2); 490 if (!rcv_len || data + HEADER_SIZE + rcv_len > end) { 491 dev_warn(&port->dev, "%s - short data\n", __func__); 492 return; 493 } 494 495 if (tty_port_initialized(&demux_port->port)) { 496 ch = data + HEADER_SIZE; 497 mxuport_process_read_urb_data(demux_port, ch, rcv_len); 498 } else { 499 dev_dbg(&demux_port->dev, "%s - data for closed port\n", 500 __func__); 501 } 502 data += HEADER_SIZE + rcv_len; 503 } 504 } 505 506 /* 507 * One URB can contain events for multiple ports. Demultiplex the event, 508 * checking the port exists, and is opened. 509 */ 510 static void mxuport_process_read_urb_demux_event(struct urb *urb) 511 { 512 struct usb_serial_port *port = urb->context; 513 struct usb_serial *serial = port->serial; 514 u8 *data = urb->transfer_buffer; 515 u8 *end = data + urb->actual_length; 516 struct usb_serial_port *demux_port; 517 u8 *ch; 518 u16 rcv_port; 519 u16 rcv_event; 520 521 while (data < end) { 522 if (data + EVENT_LENGTH > end) { 523 dev_warn(&port->dev, "%s - message with short event\n", 524 __func__); 525 return; 526 } 527 528 rcv_port = get_unaligned_be16(data); 529 if (rcv_port >= serial->num_ports) { 530 dev_warn(&port->dev, "%s - message for invalid port\n", 531 __func__); 532 return; 533 } 534 535 demux_port = serial->port[rcv_port]; 536 if (tty_port_initialized(&demux_port->port)) { 537 ch = data + HEADER_SIZE; 538 rcv_event = get_unaligned_be16(data + 2); 539 mxuport_process_read_urb_event(demux_port, ch, 540 rcv_event); 541 } else { 542 dev_dbg(&demux_port->dev, 543 "%s - event for closed port\n", __func__); 544 } 545 data += EVENT_LENGTH; 546 } 547 } 548 549 /* 550 * This is called when we have received data on the bulk in 551 * endpoint. Depending on which port it was received on, it can 552 * contain serial data or events. 553 */ 554 static void mxuport_process_read_urb(struct urb *urb) 555 { 556 struct usb_serial_port *port = urb->context; 557 struct usb_serial *serial = port->serial; 558 559 if (port == serial->port[0]) 560 mxuport_process_read_urb_demux_data(urb); 561 562 if (port == serial->port[1]) 563 mxuport_process_read_urb_demux_event(urb); 564 } 565 566 /* 567 * Ask the device how many bytes it has queued to be sent out. If 568 * there are none, return true. 569 */ 570 static bool mxuport_tx_empty(struct usb_serial_port *port) 571 { 572 struct usb_serial *serial = port->serial; 573 bool is_empty = true; 574 u32 txlen; 575 u8 *len_buf; 576 int err; 577 578 len_buf = kzalloc(4, GFP_KERNEL); 579 if (!len_buf) 580 goto out; 581 582 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_OUTQUEUE, 0, 583 port->port_number, len_buf, 4); 584 if (err < 0) 585 goto out; 586 587 txlen = get_unaligned_be32(len_buf); 588 dev_dbg(&port->dev, "%s - tx len = %u\n", __func__, txlen); 589 590 if (txlen != 0) 591 is_empty = false; 592 593 out: 594 kfree(len_buf); 595 return is_empty; 596 } 597 598 static int mxuport_set_mcr(struct usb_serial_port *port, u8 mcr_state) 599 { 600 struct usb_serial *serial = port->serial; 601 int err; 602 603 dev_dbg(&port->dev, "%s - %02x\n", __func__, mcr_state); 604 605 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_MCR, 606 mcr_state, port->port_number); 607 if (err) 608 dev_err(&port->dev, "%s - failed to change MCR\n", __func__); 609 610 return err; 611 } 612 613 static int mxuport_set_dtr(struct usb_serial_port *port, int on) 614 { 615 struct mxuport_port *mxport = usb_get_serial_port_data(port); 616 struct usb_serial *serial = port->serial; 617 int err; 618 619 mutex_lock(&mxport->mutex); 620 621 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_DTR, 622 !!on, port->port_number); 623 if (!err) { 624 if (on) 625 mxport->mcr_state |= UART_MCR_DTR; 626 else 627 mxport->mcr_state &= ~UART_MCR_DTR; 628 } 629 630 mutex_unlock(&mxport->mutex); 631 632 return err; 633 } 634 635 static int mxuport_set_rts(struct usb_serial_port *port, u8 state) 636 { 637 struct mxuport_port *mxport = usb_get_serial_port_data(port); 638 struct usb_serial *serial = port->serial; 639 int err; 640 u8 mcr_state; 641 642 mutex_lock(&mxport->mutex); 643 mcr_state = mxport->mcr_state; 644 645 switch (state) { 646 case MX_RTS_DISABLE: 647 mcr_state &= ~UART_MCR_RTS; 648 break; 649 case MX_RTS_ENABLE: 650 mcr_state |= UART_MCR_RTS; 651 break; 652 case MX_RTS_HW: 653 /* 654 * Do not update mxport->mcr_state when doing hardware 655 * flow control. 656 */ 657 break; 658 default: 659 /* 660 * Should not happen, but somebody might try passing 661 * MX_RTS_NO_CHANGE, which is not valid. 662 */ 663 err = -EINVAL; 664 goto out; 665 } 666 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RTS, 667 state, port->port_number); 668 if (!err) 669 mxport->mcr_state = mcr_state; 670 671 out: 672 mutex_unlock(&mxport->mutex); 673 674 return err; 675 } 676 677 static void mxuport_dtr_rts(struct usb_serial_port *port, int on) 678 { 679 struct mxuport_port *mxport = usb_get_serial_port_data(port); 680 u8 mcr_state; 681 int err; 682 683 mutex_lock(&mxport->mutex); 684 mcr_state = mxport->mcr_state; 685 686 if (on) 687 mcr_state |= (UART_MCR_RTS | UART_MCR_DTR); 688 else 689 mcr_state &= ~(UART_MCR_RTS | UART_MCR_DTR); 690 691 err = mxuport_set_mcr(port, mcr_state); 692 if (!err) 693 mxport->mcr_state = mcr_state; 694 695 mutex_unlock(&mxport->mutex); 696 } 697 698 static int mxuport_tiocmset(struct tty_struct *tty, unsigned int set, 699 unsigned int clear) 700 { 701 struct usb_serial_port *port = tty->driver_data; 702 struct mxuport_port *mxport = usb_get_serial_port_data(port); 703 int err; 704 u8 mcr_state; 705 706 mutex_lock(&mxport->mutex); 707 mcr_state = mxport->mcr_state; 708 709 if (set & TIOCM_RTS) 710 mcr_state |= UART_MCR_RTS; 711 712 if (set & TIOCM_DTR) 713 mcr_state |= UART_MCR_DTR; 714 715 if (clear & TIOCM_RTS) 716 mcr_state &= ~UART_MCR_RTS; 717 718 if (clear & TIOCM_DTR) 719 mcr_state &= ~UART_MCR_DTR; 720 721 err = mxuport_set_mcr(port, mcr_state); 722 if (!err) 723 mxport->mcr_state = mcr_state; 724 725 mutex_unlock(&mxport->mutex); 726 727 return err; 728 } 729 730 static int mxuport_tiocmget(struct tty_struct *tty) 731 { 732 struct mxuport_port *mxport; 733 struct usb_serial_port *port = tty->driver_data; 734 unsigned int result; 735 unsigned long flags; 736 unsigned int msr; 737 unsigned int mcr; 738 739 mxport = usb_get_serial_port_data(port); 740 741 mutex_lock(&mxport->mutex); 742 spin_lock_irqsave(&mxport->spinlock, flags); 743 744 msr = mxport->msr_state; 745 mcr = mxport->mcr_state; 746 747 spin_unlock_irqrestore(&mxport->spinlock, flags); 748 mutex_unlock(&mxport->mutex); 749 750 result = (((mcr & UART_MCR_DTR) ? TIOCM_DTR : 0) | /* 0x002 */ 751 ((mcr & UART_MCR_RTS) ? TIOCM_RTS : 0) | /* 0x004 */ 752 ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0) | /* 0x020 */ 753 ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) | /* 0x040 */ 754 ((msr & UART_MSR_RI) ? TIOCM_RI : 0) | /* 0x080 */ 755 ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0)); /* 0x100 */ 756 757 dev_dbg(&port->dev, "%s - 0x%04x\n", __func__, result); 758 759 return result; 760 } 761 762 static int mxuport_set_termios_flow(struct tty_struct *tty, 763 const struct ktermios *old_termios, 764 struct usb_serial_port *port, 765 struct usb_serial *serial) 766 { 767 u8 xon = START_CHAR(tty); 768 u8 xoff = STOP_CHAR(tty); 769 int enable; 770 int err; 771 u8 *buf; 772 u8 rts; 773 774 buf = kmalloc(2, GFP_KERNEL); 775 if (!buf) 776 return -ENOMEM; 777 778 /* S/W flow control settings */ 779 if (I_IXOFF(tty) || I_IXON(tty)) { 780 enable = 1; 781 buf[0] = xon; 782 buf[1] = xoff; 783 784 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_CHARS, 785 0, port->port_number, 786 buf, 2); 787 if (err) 788 goto out; 789 790 dev_dbg(&port->dev, "%s - XON = 0x%02x, XOFF = 0x%02x\n", 791 __func__, xon, xoff); 792 } else { 793 enable = 0; 794 } 795 796 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_XONXOFF, 797 enable, port->port_number); 798 if (err) 799 goto out; 800 801 rts = MX_RTS_NO_CHANGE; 802 803 /* H/W flow control settings */ 804 if (!old_termios || 805 C_CRTSCTS(tty) != (old_termios->c_cflag & CRTSCTS)) { 806 if (C_CRTSCTS(tty)) 807 rts = MX_RTS_HW; 808 else 809 rts = MX_RTS_ENABLE; 810 } 811 812 if (C_BAUD(tty)) { 813 if (old_termios && (old_termios->c_cflag & CBAUD) == B0) { 814 /* Raise DTR and RTS */ 815 if (C_CRTSCTS(tty)) 816 rts = MX_RTS_HW; 817 else 818 rts = MX_RTS_ENABLE; 819 mxuport_set_dtr(port, 1); 820 } 821 } else { 822 /* Drop DTR and RTS */ 823 rts = MX_RTS_DISABLE; 824 mxuport_set_dtr(port, 0); 825 } 826 827 if (rts != MX_RTS_NO_CHANGE) 828 err = mxuport_set_rts(port, rts); 829 830 out: 831 kfree(buf); 832 return err; 833 } 834 835 static void mxuport_set_termios(struct tty_struct *tty, 836 struct usb_serial_port *port, 837 const struct ktermios *old_termios) 838 { 839 struct usb_serial *serial = port->serial; 840 u8 *buf; 841 u8 data_bits; 842 u8 stop_bits; 843 u8 parity; 844 int baud; 845 int err; 846 847 if (old_termios && 848 !tty_termios_hw_change(&tty->termios, old_termios) && 849 tty->termios.c_iflag == old_termios->c_iflag) { 850 dev_dbg(&port->dev, "%s - nothing to change\n", __func__); 851 return; 852 } 853 854 buf = kmalloc(4, GFP_KERNEL); 855 if (!buf) 856 return; 857 858 /* Set data bit of termios */ 859 switch (C_CSIZE(tty)) { 860 case CS5: 861 data_bits = MX_WORDLENGTH_5; 862 break; 863 case CS6: 864 data_bits = MX_WORDLENGTH_6; 865 break; 866 case CS7: 867 data_bits = MX_WORDLENGTH_7; 868 break; 869 case CS8: 870 default: 871 data_bits = MX_WORDLENGTH_8; 872 break; 873 } 874 875 /* Set parity of termios */ 876 if (C_PARENB(tty)) { 877 if (C_CMSPAR(tty)) { 878 if (C_PARODD(tty)) 879 parity = MX_PARITY_MARK; 880 else 881 parity = MX_PARITY_SPACE; 882 } else { 883 if (C_PARODD(tty)) 884 parity = MX_PARITY_ODD; 885 else 886 parity = MX_PARITY_EVEN; 887 } 888 } else { 889 parity = MX_PARITY_NONE; 890 } 891 892 /* Set stop bit of termios */ 893 if (C_CSTOPB(tty)) 894 stop_bits = MX_STOP_BITS_2; 895 else 896 stop_bits = MX_STOP_BITS_1; 897 898 buf[0] = data_bits; 899 buf[1] = parity; 900 buf[2] = stop_bits; 901 buf[3] = 0; 902 903 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_LINE, 904 0, port->port_number, buf, 4); 905 if (err) 906 goto out; 907 908 err = mxuport_set_termios_flow(tty, old_termios, port, serial); 909 if (err) 910 goto out; 911 912 baud = tty_get_baud_rate(tty); 913 if (!baud) 914 baud = 9600; 915 916 /* Note: Little Endian */ 917 put_unaligned_le32(baud, buf); 918 919 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_BAUD, 920 0, port->port_number, 921 buf, 4); 922 if (err) 923 goto out; 924 925 dev_dbg(&port->dev, "baud_rate : %d\n", baud); 926 dev_dbg(&port->dev, "data_bits : %d\n", data_bits); 927 dev_dbg(&port->dev, "parity : %d\n", parity); 928 dev_dbg(&port->dev, "stop_bits : %d\n", stop_bits); 929 930 out: 931 kfree(buf); 932 } 933 934 /* 935 * Determine how many ports this device has dynamically. It will be 936 * called after the probe() callback is called, but before attach(). 937 */ 938 static int mxuport_calc_num_ports(struct usb_serial *serial, 939 struct usb_serial_endpoints *epds) 940 { 941 unsigned long features = (unsigned long)usb_get_serial_data(serial); 942 int num_ports; 943 int i; 944 945 if (features & MX_UPORT_2_PORT) { 946 num_ports = 2; 947 } else if (features & MX_UPORT_4_PORT) { 948 num_ports = 4; 949 } else if (features & MX_UPORT_8_PORT) { 950 num_ports = 8; 951 } else if (features & MX_UPORT_16_PORT) { 952 num_ports = 16; 953 } else { 954 dev_warn(&serial->interface->dev, 955 "unknown device, assuming two ports\n"); 956 num_ports = 2; 957 } 958 959 /* 960 * Setup bulk-out endpoint multiplexing. All ports share the same 961 * bulk-out endpoint. 962 */ 963 BUILD_BUG_ON(ARRAY_SIZE(epds->bulk_out) < 16); 964 965 for (i = 1; i < num_ports; ++i) 966 epds->bulk_out[i] = epds->bulk_out[0]; 967 968 epds->num_bulk_out = num_ports; 969 970 return num_ports; 971 } 972 973 /* Get the version of the firmware currently running. */ 974 static int mxuport_get_fw_version(struct usb_serial *serial, u32 *version) 975 { 976 u8 *ver_buf; 977 int err; 978 979 ver_buf = kzalloc(4, GFP_KERNEL); 980 if (!ver_buf) 981 return -ENOMEM; 982 983 /* Get firmware version from SDRAM */ 984 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_VERSION, 0, 0, 985 ver_buf, 4); 986 if (err != 4) { 987 err = -EIO; 988 goto out; 989 } 990 991 *version = (ver_buf[0] << 16) | (ver_buf[1] << 8) | ver_buf[2]; 992 err = 0; 993 out: 994 kfree(ver_buf); 995 return err; 996 } 997 998 /* Given a firmware blob, download it to the device. */ 999 static int mxuport_download_fw(struct usb_serial *serial, 1000 const struct firmware *fw_p) 1001 { 1002 u8 *fw_buf; 1003 size_t txlen; 1004 size_t fwidx; 1005 int err; 1006 1007 fw_buf = kmalloc(DOWN_BLOCK_SIZE, GFP_KERNEL); 1008 if (!fw_buf) 1009 return -ENOMEM; 1010 1011 dev_dbg(&serial->interface->dev, "Starting firmware download...\n"); 1012 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_START_FW_DOWN, 0, 0); 1013 if (err) 1014 goto out; 1015 1016 fwidx = 0; 1017 do { 1018 txlen = min_t(size_t, (fw_p->size - fwidx), DOWN_BLOCK_SIZE); 1019 1020 memcpy(fw_buf, &fw_p->data[fwidx], txlen); 1021 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_FW_DATA, 1022 0, 0, fw_buf, txlen); 1023 if (err) { 1024 mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 1025 0, 0); 1026 goto out; 1027 } 1028 1029 fwidx += txlen; 1030 usleep_range(1000, 2000); 1031 1032 } while (fwidx < fw_p->size); 1033 1034 msleep(1000); 1035 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 0, 0); 1036 if (err) 1037 goto out; 1038 1039 msleep(1000); 1040 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_READY, 0, 0); 1041 1042 out: 1043 kfree(fw_buf); 1044 return err; 1045 } 1046 1047 static int mxuport_probe(struct usb_serial *serial, 1048 const struct usb_device_id *id) 1049 { 1050 u16 productid = le16_to_cpu(serial->dev->descriptor.idProduct); 1051 const struct firmware *fw_p = NULL; 1052 u32 version; 1053 int local_ver; 1054 char buf[32]; 1055 int err; 1056 1057 /* Load our firmware */ 1058 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_CONFIG, 0, 0); 1059 if (err) { 1060 mxuport_send_ctrl_urb(serial, RQ_VENDOR_RESET_DEVICE, 0, 0); 1061 return err; 1062 } 1063 1064 err = mxuport_get_fw_version(serial, &version); 1065 if (err < 0) 1066 return err; 1067 1068 dev_dbg(&serial->interface->dev, "Device firmware version v%x.%x.%x\n", 1069 (version & 0xff0000) >> 16, 1070 (version & 0xff00) >> 8, 1071 (version & 0xff)); 1072 1073 snprintf(buf, sizeof(buf) - 1, "moxa/moxa-%04x.fw", productid); 1074 1075 err = request_firmware(&fw_p, buf, &serial->interface->dev); 1076 if (err) { 1077 dev_warn(&serial->interface->dev, "Firmware %s not found\n", 1078 buf); 1079 1080 /* Use the firmware already in the device */ 1081 err = 0; 1082 } else { 1083 local_ver = ((fw_p->data[VER_ADDR_1] << 16) | 1084 (fw_p->data[VER_ADDR_2] << 8) | 1085 fw_p->data[VER_ADDR_3]); 1086 dev_dbg(&serial->interface->dev, 1087 "Available firmware version v%x.%x.%x\n", 1088 fw_p->data[VER_ADDR_1], fw_p->data[VER_ADDR_2], 1089 fw_p->data[VER_ADDR_3]); 1090 if (local_ver > version) { 1091 err = mxuport_download_fw(serial, fw_p); 1092 if (err) 1093 goto out; 1094 err = mxuport_get_fw_version(serial, &version); 1095 if (err < 0) 1096 goto out; 1097 } 1098 } 1099 1100 dev_info(&serial->interface->dev, 1101 "Using device firmware version v%x.%x.%x\n", 1102 (version & 0xff0000) >> 16, 1103 (version & 0xff00) >> 8, 1104 (version & 0xff)); 1105 1106 /* 1107 * Contains the features of this hardware. Store away for 1108 * later use, eg, number of ports. 1109 */ 1110 usb_set_serial_data(serial, (void *)id->driver_info); 1111 out: 1112 if (fw_p) 1113 release_firmware(fw_p); 1114 return err; 1115 } 1116 1117 1118 static int mxuport_port_probe(struct usb_serial_port *port) 1119 { 1120 struct usb_serial *serial = port->serial; 1121 struct mxuport_port *mxport; 1122 int err; 1123 1124 mxport = devm_kzalloc(&port->dev, sizeof(struct mxuport_port), 1125 GFP_KERNEL); 1126 if (!mxport) 1127 return -ENOMEM; 1128 1129 mutex_init(&mxport->mutex); 1130 spin_lock_init(&mxport->spinlock); 1131 1132 /* Set the port private data */ 1133 usb_set_serial_port_data(port, mxport); 1134 1135 /* Set FIFO (Enable) */ 1136 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_FIFO_DISABLE, 1137 0, port->port_number); 1138 if (err) 1139 return err; 1140 1141 /* Set transmission mode (Hi-Performance) */ 1142 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_HIGH_PERFOR, 1143 0, port->port_number); 1144 if (err) 1145 return err; 1146 1147 /* Set interface (RS-232) */ 1148 return mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_INTERFACE, 1149 MX_INT_RS232, 1150 port->port_number); 1151 } 1152 1153 static int mxuport_attach(struct usb_serial *serial) 1154 { 1155 struct usb_serial_port *port0 = serial->port[0]; 1156 struct usb_serial_port *port1 = serial->port[1]; 1157 int err; 1158 1159 /* 1160 * All data from the ports is received on the first bulk in 1161 * endpoint, with a multiplex header. The second bulk in is 1162 * used for events. 1163 * 1164 * Start to read from the device. 1165 */ 1166 err = usb_serial_generic_submit_read_urbs(port0, GFP_KERNEL); 1167 if (err) 1168 return err; 1169 1170 err = usb_serial_generic_submit_read_urbs(port1, GFP_KERNEL); 1171 if (err) { 1172 usb_serial_generic_close(port0); 1173 return err; 1174 } 1175 1176 return 0; 1177 } 1178 1179 static void mxuport_release(struct usb_serial *serial) 1180 { 1181 struct usb_serial_port *port0 = serial->port[0]; 1182 struct usb_serial_port *port1 = serial->port[1]; 1183 1184 usb_serial_generic_close(port1); 1185 usb_serial_generic_close(port0); 1186 } 1187 1188 static int mxuport_open(struct tty_struct *tty, struct usb_serial_port *port) 1189 { 1190 struct mxuport_port *mxport = usb_get_serial_port_data(port); 1191 struct usb_serial *serial = port->serial; 1192 int err; 1193 1194 /* Set receive host (enable) */ 1195 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 1196 1, port->port_number); 1197 if (err) 1198 return err; 1199 1200 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 1201 1, port->port_number); 1202 if (err) { 1203 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 1204 0, port->port_number); 1205 return err; 1206 } 1207 1208 /* Initial port termios */ 1209 if (tty) 1210 mxuport_set_termios(tty, port, NULL); 1211 1212 /* 1213 * TODO: use RQ_VENDOR_GET_MSR, once we know what it 1214 * returns. 1215 */ 1216 mxport->msr_state = 0; 1217 1218 return err; 1219 } 1220 1221 static void mxuport_close(struct usb_serial_port *port) 1222 { 1223 struct usb_serial *serial = port->serial; 1224 1225 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 0, 1226 port->port_number); 1227 1228 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 0, 1229 port->port_number); 1230 } 1231 1232 /* Send a break to the port. */ 1233 static void mxuport_break_ctl(struct tty_struct *tty, int break_state) 1234 { 1235 struct usb_serial_port *port = tty->driver_data; 1236 struct usb_serial *serial = port->serial; 1237 int enable; 1238 1239 if (break_state == -1) { 1240 enable = 1; 1241 dev_dbg(&port->dev, "%s - sending break\n", __func__); 1242 } else { 1243 enable = 0; 1244 dev_dbg(&port->dev, "%s - clearing break\n", __func__); 1245 } 1246 1247 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_BREAK, 1248 enable, port->port_number); 1249 } 1250 1251 static int mxuport_resume(struct usb_serial *serial) 1252 { 1253 struct usb_serial_port *port; 1254 int c = 0; 1255 int i; 1256 int r; 1257 1258 for (i = 0; i < 2; i++) { 1259 port = serial->port[i]; 1260 1261 r = usb_serial_generic_submit_read_urbs(port, GFP_NOIO); 1262 if (r < 0) 1263 c++; 1264 } 1265 1266 for (i = 0; i < serial->num_ports; i++) { 1267 port = serial->port[i]; 1268 if (!tty_port_initialized(&port->port)) 1269 continue; 1270 1271 r = usb_serial_generic_write_start(port, GFP_NOIO); 1272 if (r < 0) 1273 c++; 1274 } 1275 1276 return c ? -EIO : 0; 1277 } 1278 1279 static struct usb_serial_driver mxuport_device = { 1280 .driver = { 1281 .owner = THIS_MODULE, 1282 .name = "mxuport", 1283 }, 1284 .description = "MOXA UPort", 1285 .id_table = mxuport_idtable, 1286 .num_bulk_in = 2, 1287 .num_bulk_out = 1, 1288 .probe = mxuport_probe, 1289 .port_probe = mxuport_port_probe, 1290 .attach = mxuport_attach, 1291 .release = mxuport_release, 1292 .calc_num_ports = mxuport_calc_num_ports, 1293 .open = mxuport_open, 1294 .close = mxuport_close, 1295 .set_termios = mxuport_set_termios, 1296 .break_ctl = mxuport_break_ctl, 1297 .tx_empty = mxuport_tx_empty, 1298 .tiocmiwait = usb_serial_generic_tiocmiwait, 1299 .get_icount = usb_serial_generic_get_icount, 1300 .throttle = mxuport_throttle, 1301 .unthrottle = mxuport_unthrottle, 1302 .tiocmget = mxuport_tiocmget, 1303 .tiocmset = mxuport_tiocmset, 1304 .dtr_rts = mxuport_dtr_rts, 1305 .process_read_urb = mxuport_process_read_urb, 1306 .prepare_write_buffer = mxuport_prepare_write_buffer, 1307 .resume = mxuport_resume, 1308 }; 1309 1310 static struct usb_serial_driver *const serial_drivers[] = { 1311 &mxuport_device, NULL 1312 }; 1313 1314 module_usb_serial_driver(serial_drivers, mxuport_idtable); 1315 1316 MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>"); 1317 MODULE_AUTHOR("<support@moxa.com>"); 1318 MODULE_LICENSE("GPL"); 1319