1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * mxuport.c - MOXA UPort series driver
4 *
5 * Copyright (c) 2006 Moxa Technologies Co., Ltd.
6 * Copyright (c) 2013 Andrew Lunn <andrew@lunn.ch>
7 *
8 * Supports the following Moxa USB to serial converters:
9 * 2 ports : UPort 1250, UPort 1250I
10 * 4 ports : UPort 1410, UPort 1450, UPort 1450I
11 * 8 ports : UPort 1610-8, UPort 1650-8
12 * 16 ports : UPort 1610-16, UPort 1650-16
13 */
14
15 #include <linux/kernel.h>
16 #include <linux/module.h>
17 #include <linux/firmware.h>
18 #include <linux/jiffies.h>
19 #include <linux/serial.h>
20 #include <linux/serial_reg.h>
21 #include <linux/slab.h>
22 #include <linux/tty.h>
23 #include <linux/tty_driver.h>
24 #include <linux/tty_flip.h>
25 #include <linux/uaccess.h>
26 #include <linux/usb.h>
27 #include <linux/usb/serial.h>
28 #include <asm/unaligned.h>
29
30 /* Definitions for the vendor ID and device ID */
31 #define MX_USBSERIAL_VID 0x110A
32 #define MX_UPORT1250_PID 0x1250
33 #define MX_UPORT1251_PID 0x1251
34 #define MX_UPORT1410_PID 0x1410
35 #define MX_UPORT1450_PID 0x1450
36 #define MX_UPORT1451_PID 0x1451
37 #define MX_UPORT1618_PID 0x1618
38 #define MX_UPORT1658_PID 0x1658
39 #define MX_UPORT1613_PID 0x1613
40 #define MX_UPORT1653_PID 0x1653
41
42 /* Definitions for USB info */
43 #define HEADER_SIZE 4
44 #define EVENT_LENGTH 8
45 #define DOWN_BLOCK_SIZE 64
46
47 /* Definitions for firmware info */
48 #define VER_ADDR_1 0x20
49 #define VER_ADDR_2 0x24
50 #define VER_ADDR_3 0x28
51
52 /* Definitions for USB vendor request */
53 #define RQ_VENDOR_NONE 0x00
54 #define RQ_VENDOR_SET_BAUD 0x01 /* Set baud rate */
55 #define RQ_VENDOR_SET_LINE 0x02 /* Set line status */
56 #define RQ_VENDOR_SET_CHARS 0x03 /* Set Xon/Xoff chars */
57 #define RQ_VENDOR_SET_RTS 0x04 /* Set RTS */
58 #define RQ_VENDOR_SET_DTR 0x05 /* Set DTR */
59 #define RQ_VENDOR_SET_XONXOFF 0x06 /* Set auto Xon/Xoff */
60 #define RQ_VENDOR_SET_RX_HOST_EN 0x07 /* Set RX host enable */
61 #define RQ_VENDOR_SET_OPEN 0x08 /* Set open/close port */
62 #define RQ_VENDOR_PURGE 0x09 /* Purge Rx/Tx buffer */
63 #define RQ_VENDOR_SET_MCR 0x0A /* Set MCR register */
64 #define RQ_VENDOR_SET_BREAK 0x0B /* Set Break signal */
65
66 #define RQ_VENDOR_START_FW_DOWN 0x0C /* Start firmware download */
67 #define RQ_VENDOR_STOP_FW_DOWN 0x0D /* Stop firmware download */
68 #define RQ_VENDOR_QUERY_FW_READY 0x0E /* Query if new firmware ready */
69
70 #define RQ_VENDOR_SET_FIFO_DISABLE 0x0F /* Set fifo disable */
71 #define RQ_VENDOR_SET_INTERFACE 0x10 /* Set interface */
72 #define RQ_VENDOR_SET_HIGH_PERFOR 0x11 /* Set hi-performance */
73
74 #define RQ_VENDOR_ERASE_BLOCK 0x12 /* Erase flash block */
75 #define RQ_VENDOR_WRITE_PAGE 0x13 /* Write flash page */
76 #define RQ_VENDOR_PREPARE_WRITE 0x14 /* Prepare write flash */
77 #define RQ_VENDOR_CONFIRM_WRITE 0x15 /* Confirm write flash */
78 #define RQ_VENDOR_LOCATE 0x16 /* Locate the device */
79
80 #define RQ_VENDOR_START_ROM_DOWN 0x17 /* Start firmware download */
81 #define RQ_VENDOR_ROM_DATA 0x18 /* Rom file data */
82 #define RQ_VENDOR_STOP_ROM_DOWN 0x19 /* Stop firmware download */
83 #define RQ_VENDOR_FW_DATA 0x20 /* Firmware data */
84
85 #define RQ_VENDOR_RESET_DEVICE 0x23 /* Try to reset the device */
86 #define RQ_VENDOR_QUERY_FW_CONFIG 0x24
87
88 #define RQ_VENDOR_GET_VERSION 0x81 /* Get firmware version */
89 #define RQ_VENDOR_GET_PAGE 0x82 /* Read flash page */
90 #define RQ_VENDOR_GET_ROM_PROC 0x83 /* Get ROM process state */
91
92 #define RQ_VENDOR_GET_INQUEUE 0x84 /* Data in input buffer */
93 #define RQ_VENDOR_GET_OUTQUEUE 0x85 /* Data in output buffer */
94
95 #define RQ_VENDOR_GET_MSR 0x86 /* Get modem status register */
96
97 /* Definitions for UPort event type */
98 #define UPORT_EVENT_NONE 0 /* None */
99 #define UPORT_EVENT_TXBUF_THRESHOLD 1 /* Tx buffer threshold */
100 #define UPORT_EVENT_SEND_NEXT 2 /* Send next */
101 #define UPORT_EVENT_MSR 3 /* Modem status */
102 #define UPORT_EVENT_LSR 4 /* Line status */
103 #define UPORT_EVENT_MCR 5 /* Modem control */
104
105 /* Definitions for serial event type */
106 #define SERIAL_EV_CTS 0x0008 /* CTS changed state */
107 #define SERIAL_EV_DSR 0x0010 /* DSR changed state */
108 #define SERIAL_EV_RLSD 0x0020 /* RLSD changed state */
109
110 /* Definitions for modem control event type */
111 #define SERIAL_EV_XOFF 0x40 /* XOFF received */
112
113 /* Definitions for line control of communication */
114 #define MX_WORDLENGTH_5 5
115 #define MX_WORDLENGTH_6 6
116 #define MX_WORDLENGTH_7 7
117 #define MX_WORDLENGTH_8 8
118
119 #define MX_PARITY_NONE 0
120 #define MX_PARITY_ODD 1
121 #define MX_PARITY_EVEN 2
122 #define MX_PARITY_MARK 3
123 #define MX_PARITY_SPACE 4
124
125 #define MX_STOP_BITS_1 0
126 #define MX_STOP_BITS_1_5 1
127 #define MX_STOP_BITS_2 2
128
129 #define MX_RTS_DISABLE 0x0
130 #define MX_RTS_ENABLE 0x1
131 #define MX_RTS_HW 0x2
132 #define MX_RTS_NO_CHANGE 0x3 /* Flag, not valid register value*/
133
134 #define MX_INT_RS232 0
135 #define MX_INT_2W_RS485 1
136 #define MX_INT_RS422 2
137 #define MX_INT_4W_RS485 3
138
139 /* Definitions for holding reason */
140 #define MX_WAIT_FOR_CTS 0x0001
141 #define MX_WAIT_FOR_DSR 0x0002
142 #define MX_WAIT_FOR_DCD 0x0004
143 #define MX_WAIT_FOR_XON 0x0008
144 #define MX_WAIT_FOR_START_TX 0x0010
145 #define MX_WAIT_FOR_UNTHROTTLE 0x0020
146 #define MX_WAIT_FOR_LOW_WATER 0x0040
147 #define MX_WAIT_FOR_SEND_NEXT 0x0080
148
149 #define MX_UPORT_2_PORT BIT(0)
150 #define MX_UPORT_4_PORT BIT(1)
151 #define MX_UPORT_8_PORT BIT(2)
152 #define MX_UPORT_16_PORT BIT(3)
153
154 /* This structure holds all of the local port information */
155 struct mxuport_port {
156 u8 mcr_state; /* Last MCR state */
157 u8 msr_state; /* Last MSR state */
158 struct mutex mutex; /* Protects mcr_state */
159 spinlock_t spinlock; /* Protects msr_state */
160 };
161
162 /* Table of devices that work with this driver */
163 static const struct usb_device_id mxuport_idtable[] = {
164 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1250_PID),
165 .driver_info = MX_UPORT_2_PORT },
166 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1251_PID),
167 .driver_info = MX_UPORT_2_PORT },
168 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1410_PID),
169 .driver_info = MX_UPORT_4_PORT },
170 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1450_PID),
171 .driver_info = MX_UPORT_4_PORT },
172 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1451_PID),
173 .driver_info = MX_UPORT_4_PORT },
174 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1618_PID),
175 .driver_info = MX_UPORT_8_PORT },
176 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1658_PID),
177 .driver_info = MX_UPORT_8_PORT },
178 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1613_PID),
179 .driver_info = MX_UPORT_16_PORT },
180 { USB_DEVICE(MX_USBSERIAL_VID, MX_UPORT1653_PID),
181 .driver_info = MX_UPORT_16_PORT },
182 {} /* Terminating entry */
183 };
184
185 MODULE_DEVICE_TABLE(usb, mxuport_idtable);
186
187 /*
188 * Add a four byte header containing the port number and the number of
189 * bytes of data in the message. Return the number of bytes in the
190 * buffer.
191 */
mxuport_prepare_write_buffer(struct usb_serial_port * port,void * dest,size_t size)192 static int mxuport_prepare_write_buffer(struct usb_serial_port *port,
193 void *dest, size_t size)
194 {
195 u8 *buf = dest;
196 int count;
197
198 count = kfifo_out_locked(&port->write_fifo, buf + HEADER_SIZE,
199 size - HEADER_SIZE,
200 &port->lock);
201
202 put_unaligned_be16(port->port_number, buf);
203 put_unaligned_be16(count, buf + 2);
204
205 dev_dbg(&port->dev, "%s - size %zd count %d\n", __func__,
206 size, count);
207
208 return count + HEADER_SIZE;
209 }
210
211 /* Read the given buffer in from the control pipe. */
mxuport_recv_ctrl_urb(struct usb_serial * serial,u8 request,u16 value,u16 index,u8 * data,size_t size)212 static int mxuport_recv_ctrl_urb(struct usb_serial *serial,
213 u8 request, u16 value, u16 index,
214 u8 *data, size_t size)
215 {
216 int status;
217
218 status = usb_control_msg(serial->dev,
219 usb_rcvctrlpipe(serial->dev, 0),
220 request,
221 (USB_DIR_IN | USB_TYPE_VENDOR |
222 USB_RECIP_DEVICE), value, index,
223 data, size,
224 USB_CTRL_GET_TIMEOUT);
225 if (status < 0) {
226 dev_err(&serial->interface->dev,
227 "%s - usb_control_msg failed (%d)\n",
228 __func__, status);
229 return status;
230 }
231
232 if (status != size) {
233 dev_err(&serial->interface->dev,
234 "%s - short read (%d / %zd)\n",
235 __func__, status, size);
236 return -EIO;
237 }
238
239 return status;
240 }
241
242 /* Write the given buffer out to the control pipe. */
mxuport_send_ctrl_data_urb(struct usb_serial * serial,u8 request,u16 value,u16 index,u8 * data,size_t size)243 static int mxuport_send_ctrl_data_urb(struct usb_serial *serial,
244 u8 request,
245 u16 value, u16 index,
246 u8 *data, size_t size)
247 {
248 int status;
249
250 status = usb_control_msg(serial->dev,
251 usb_sndctrlpipe(serial->dev, 0),
252 request,
253 (USB_DIR_OUT | USB_TYPE_VENDOR |
254 USB_RECIP_DEVICE), value, index,
255 data, size,
256 USB_CTRL_SET_TIMEOUT);
257 if (status < 0) {
258 dev_err(&serial->interface->dev,
259 "%s - usb_control_msg failed (%d)\n",
260 __func__, status);
261 return status;
262 }
263
264 return 0;
265 }
266
267 /* Send a vendor request without any data */
mxuport_send_ctrl_urb(struct usb_serial * serial,u8 request,u16 value,u16 index)268 static int mxuport_send_ctrl_urb(struct usb_serial *serial,
269 u8 request, u16 value, u16 index)
270 {
271 return mxuport_send_ctrl_data_urb(serial, request, value, index,
272 NULL, 0);
273 }
274
275 /*
276 * mxuport_throttle - throttle function of driver
277 *
278 * This function is called by the tty driver when it wants to stop the
279 * data being read from the port. Since all the data comes over one
280 * bulk in endpoint, we cannot stop submitting urbs by setting
281 * port->throttle. Instead tell the device to stop sending us data for
282 * the port.
283 */
mxuport_throttle(struct tty_struct * tty)284 static void mxuport_throttle(struct tty_struct *tty)
285 {
286 struct usb_serial_port *port = tty->driver_data;
287 struct usb_serial *serial = port->serial;
288
289 dev_dbg(&port->dev, "%s\n", __func__);
290
291 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
292 0, port->port_number);
293 }
294
295 /*
296 * mxuport_unthrottle - unthrottle function of driver
297 *
298 * This function is called by the tty driver when it wants to resume
299 * the data being read from the port. Tell the device it can resume
300 * sending us received data from the port.
301 */
mxuport_unthrottle(struct tty_struct * tty)302 static void mxuport_unthrottle(struct tty_struct *tty)
303 {
304
305 struct usb_serial_port *port = tty->driver_data;
306 struct usb_serial *serial = port->serial;
307
308 dev_dbg(&port->dev, "%s\n", __func__);
309
310 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
311 1, port->port_number);
312 }
313
314 /*
315 * Processes one chunk of data received for a port. Mostly a copy of
316 * usb_serial_generic_process_read_urb().
317 */
mxuport_process_read_urb_data(struct usb_serial_port * port,char * data,int size)318 static void mxuport_process_read_urb_data(struct usb_serial_port *port,
319 char *data, int size)
320 {
321 int i;
322
323 if (port->sysrq) {
324 for (i = 0; i < size; i++, data++) {
325 if (!usb_serial_handle_sysrq_char(port, *data))
326 tty_insert_flip_char(&port->port, *data,
327 TTY_NORMAL);
328 }
329 } else {
330 tty_insert_flip_string(&port->port, data, size);
331 }
332 tty_flip_buffer_push(&port->port);
333 }
334
mxuport_msr_event(struct usb_serial_port * port,u8 buf[4])335 static void mxuport_msr_event(struct usb_serial_port *port, u8 buf[4])
336 {
337 struct mxuport_port *mxport = usb_get_serial_port_data(port);
338 u8 rcv_msr_hold = buf[2] & 0xF0;
339 u16 rcv_msr_event = get_unaligned_be16(buf);
340 unsigned long flags;
341
342 if (rcv_msr_event == 0)
343 return;
344
345 /* Update MSR status */
346 spin_lock_irqsave(&mxport->spinlock, flags);
347
348 dev_dbg(&port->dev, "%s - current MSR status = 0x%x\n",
349 __func__, mxport->msr_state);
350
351 if (rcv_msr_hold & UART_MSR_CTS) {
352 mxport->msr_state |= UART_MSR_CTS;
353 dev_dbg(&port->dev, "%s - CTS high\n", __func__);
354 } else {
355 mxport->msr_state &= ~UART_MSR_CTS;
356 dev_dbg(&port->dev, "%s - CTS low\n", __func__);
357 }
358
359 if (rcv_msr_hold & UART_MSR_DSR) {
360 mxport->msr_state |= UART_MSR_DSR;
361 dev_dbg(&port->dev, "%s - DSR high\n", __func__);
362 } else {
363 mxport->msr_state &= ~UART_MSR_DSR;
364 dev_dbg(&port->dev, "%s - DSR low\n", __func__);
365 }
366
367 if (rcv_msr_hold & UART_MSR_DCD) {
368 mxport->msr_state |= UART_MSR_DCD;
369 dev_dbg(&port->dev, "%s - DCD high\n", __func__);
370 } else {
371 mxport->msr_state &= ~UART_MSR_DCD;
372 dev_dbg(&port->dev, "%s - DCD low\n", __func__);
373 }
374 spin_unlock_irqrestore(&mxport->spinlock, flags);
375
376 if (rcv_msr_event &
377 (SERIAL_EV_CTS | SERIAL_EV_DSR | SERIAL_EV_RLSD)) {
378
379 if (rcv_msr_event & SERIAL_EV_CTS) {
380 port->icount.cts++;
381 dev_dbg(&port->dev, "%s - CTS change\n", __func__);
382 }
383
384 if (rcv_msr_event & SERIAL_EV_DSR) {
385 port->icount.dsr++;
386 dev_dbg(&port->dev, "%s - DSR change\n", __func__);
387 }
388
389 if (rcv_msr_event & SERIAL_EV_RLSD) {
390 port->icount.dcd++;
391 dev_dbg(&port->dev, "%s - DCD change\n", __func__);
392 }
393 wake_up_interruptible(&port->port.delta_msr_wait);
394 }
395 }
396
mxuport_lsr_event(struct usb_serial_port * port,u8 buf[4])397 static void mxuport_lsr_event(struct usb_serial_port *port, u8 buf[4])
398 {
399 u8 lsr_event = buf[2];
400
401 if (lsr_event & UART_LSR_BI) {
402 port->icount.brk++;
403 dev_dbg(&port->dev, "%s - break error\n", __func__);
404 }
405
406 if (lsr_event & UART_LSR_FE) {
407 port->icount.frame++;
408 dev_dbg(&port->dev, "%s - frame error\n", __func__);
409 }
410
411 if (lsr_event & UART_LSR_PE) {
412 port->icount.parity++;
413 dev_dbg(&port->dev, "%s - parity error\n", __func__);
414 }
415
416 if (lsr_event & UART_LSR_OE) {
417 port->icount.overrun++;
418 dev_dbg(&port->dev, "%s - overrun error\n", __func__);
419 }
420 }
421
422 /*
423 * When something interesting happens, modem control lines XON/XOFF
424 * etc, the device sends an event. Process these events.
425 */
mxuport_process_read_urb_event(struct usb_serial_port * port,u8 buf[4],u32 event)426 static void mxuport_process_read_urb_event(struct usb_serial_port *port,
427 u8 buf[4], u32 event)
428 {
429 dev_dbg(&port->dev, "%s - receive event : %04x\n", __func__, event);
430
431 switch (event) {
432 case UPORT_EVENT_SEND_NEXT:
433 /*
434 * Sent as part of the flow control on device buffers.
435 * Not currently used.
436 */
437 break;
438 case UPORT_EVENT_MSR:
439 mxuport_msr_event(port, buf);
440 break;
441 case UPORT_EVENT_LSR:
442 mxuport_lsr_event(port, buf);
443 break;
444 case UPORT_EVENT_MCR:
445 /*
446 * Event to indicate a change in XON/XOFF from the
447 * peer. Currently not used. We just continue
448 * sending the device data and it will buffer it if
449 * needed. This event could be used for flow control
450 * between the host and the device.
451 */
452 break;
453 default:
454 dev_dbg(&port->dev, "Unexpected event\n");
455 break;
456 }
457 }
458
459 /*
460 * One URB can contain data for multiple ports. Demultiplex the data,
461 * checking the port exists, is opened and the message is valid.
462 */
mxuport_process_read_urb_demux_data(struct urb * urb)463 static void mxuport_process_read_urb_demux_data(struct urb *urb)
464 {
465 struct usb_serial_port *port = urb->context;
466 struct usb_serial *serial = port->serial;
467 u8 *data = urb->transfer_buffer;
468 u8 *end = data + urb->actual_length;
469 struct usb_serial_port *demux_port;
470 u8 *ch;
471 u16 rcv_port;
472 u16 rcv_len;
473
474 while (data < end) {
475 if (data + HEADER_SIZE > end) {
476 dev_warn(&port->dev, "%s - message with short header\n",
477 __func__);
478 return;
479 }
480
481 rcv_port = get_unaligned_be16(data);
482 if (rcv_port >= serial->num_ports) {
483 dev_warn(&port->dev, "%s - message for invalid port\n",
484 __func__);
485 return;
486 }
487
488 demux_port = serial->port[rcv_port];
489 rcv_len = get_unaligned_be16(data + 2);
490 if (!rcv_len || data + HEADER_SIZE + rcv_len > end) {
491 dev_warn(&port->dev, "%s - short data\n", __func__);
492 return;
493 }
494
495 if (tty_port_initialized(&demux_port->port)) {
496 ch = data + HEADER_SIZE;
497 mxuport_process_read_urb_data(demux_port, ch, rcv_len);
498 } else {
499 dev_dbg(&demux_port->dev, "%s - data for closed port\n",
500 __func__);
501 }
502 data += HEADER_SIZE + rcv_len;
503 }
504 }
505
506 /*
507 * One URB can contain events for multiple ports. Demultiplex the event,
508 * checking the port exists, and is opened.
509 */
mxuport_process_read_urb_demux_event(struct urb * urb)510 static void mxuport_process_read_urb_demux_event(struct urb *urb)
511 {
512 struct usb_serial_port *port = urb->context;
513 struct usb_serial *serial = port->serial;
514 u8 *data = urb->transfer_buffer;
515 u8 *end = data + urb->actual_length;
516 struct usb_serial_port *demux_port;
517 u8 *ch;
518 u16 rcv_port;
519 u16 rcv_event;
520
521 while (data < end) {
522 if (data + EVENT_LENGTH > end) {
523 dev_warn(&port->dev, "%s - message with short event\n",
524 __func__);
525 return;
526 }
527
528 rcv_port = get_unaligned_be16(data);
529 if (rcv_port >= serial->num_ports) {
530 dev_warn(&port->dev, "%s - message for invalid port\n",
531 __func__);
532 return;
533 }
534
535 demux_port = serial->port[rcv_port];
536 if (tty_port_initialized(&demux_port->port)) {
537 ch = data + HEADER_SIZE;
538 rcv_event = get_unaligned_be16(data + 2);
539 mxuport_process_read_urb_event(demux_port, ch,
540 rcv_event);
541 } else {
542 dev_dbg(&demux_port->dev,
543 "%s - event for closed port\n", __func__);
544 }
545 data += EVENT_LENGTH;
546 }
547 }
548
549 /*
550 * This is called when we have received data on the bulk in
551 * endpoint. Depending on which port it was received on, it can
552 * contain serial data or events.
553 */
mxuport_process_read_urb(struct urb * urb)554 static void mxuport_process_read_urb(struct urb *urb)
555 {
556 struct usb_serial_port *port = urb->context;
557 struct usb_serial *serial = port->serial;
558
559 if (port == serial->port[0])
560 mxuport_process_read_urb_demux_data(urb);
561
562 if (port == serial->port[1])
563 mxuport_process_read_urb_demux_event(urb);
564 }
565
566 /*
567 * Ask the device how many bytes it has queued to be sent out. If
568 * there are none, return true.
569 */
mxuport_tx_empty(struct usb_serial_port * port)570 static bool mxuport_tx_empty(struct usb_serial_port *port)
571 {
572 struct usb_serial *serial = port->serial;
573 bool is_empty = true;
574 u32 txlen;
575 u8 *len_buf;
576 int err;
577
578 len_buf = kzalloc(4, GFP_KERNEL);
579 if (!len_buf)
580 goto out;
581
582 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_OUTQUEUE, 0,
583 port->port_number, len_buf, 4);
584 if (err < 0)
585 goto out;
586
587 txlen = get_unaligned_be32(len_buf);
588 dev_dbg(&port->dev, "%s - tx len = %u\n", __func__, txlen);
589
590 if (txlen != 0)
591 is_empty = false;
592
593 out:
594 kfree(len_buf);
595 return is_empty;
596 }
597
mxuport_set_mcr(struct usb_serial_port * port,u8 mcr_state)598 static int mxuport_set_mcr(struct usb_serial_port *port, u8 mcr_state)
599 {
600 struct usb_serial *serial = port->serial;
601 int err;
602
603 dev_dbg(&port->dev, "%s - %02x\n", __func__, mcr_state);
604
605 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_MCR,
606 mcr_state, port->port_number);
607 if (err)
608 dev_err(&port->dev, "%s - failed to change MCR\n", __func__);
609
610 return err;
611 }
612
mxuport_set_dtr(struct usb_serial_port * port,int on)613 static int mxuport_set_dtr(struct usb_serial_port *port, int on)
614 {
615 struct mxuport_port *mxport = usb_get_serial_port_data(port);
616 struct usb_serial *serial = port->serial;
617 int err;
618
619 mutex_lock(&mxport->mutex);
620
621 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_DTR,
622 !!on, port->port_number);
623 if (!err) {
624 if (on)
625 mxport->mcr_state |= UART_MCR_DTR;
626 else
627 mxport->mcr_state &= ~UART_MCR_DTR;
628 }
629
630 mutex_unlock(&mxport->mutex);
631
632 return err;
633 }
634
mxuport_set_rts(struct usb_serial_port * port,u8 state)635 static int mxuport_set_rts(struct usb_serial_port *port, u8 state)
636 {
637 struct mxuport_port *mxport = usb_get_serial_port_data(port);
638 struct usb_serial *serial = port->serial;
639 int err;
640 u8 mcr_state;
641
642 mutex_lock(&mxport->mutex);
643 mcr_state = mxport->mcr_state;
644
645 switch (state) {
646 case MX_RTS_DISABLE:
647 mcr_state &= ~UART_MCR_RTS;
648 break;
649 case MX_RTS_ENABLE:
650 mcr_state |= UART_MCR_RTS;
651 break;
652 case MX_RTS_HW:
653 /*
654 * Do not update mxport->mcr_state when doing hardware
655 * flow control.
656 */
657 break;
658 default:
659 /*
660 * Should not happen, but somebody might try passing
661 * MX_RTS_NO_CHANGE, which is not valid.
662 */
663 err = -EINVAL;
664 goto out;
665 }
666 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RTS,
667 state, port->port_number);
668 if (!err)
669 mxport->mcr_state = mcr_state;
670
671 out:
672 mutex_unlock(&mxport->mutex);
673
674 return err;
675 }
676
mxuport_dtr_rts(struct usb_serial_port * port,int on)677 static void mxuport_dtr_rts(struct usb_serial_port *port, int on)
678 {
679 struct mxuport_port *mxport = usb_get_serial_port_data(port);
680 u8 mcr_state;
681 int err;
682
683 mutex_lock(&mxport->mutex);
684 mcr_state = mxport->mcr_state;
685
686 if (on)
687 mcr_state |= (UART_MCR_RTS | UART_MCR_DTR);
688 else
689 mcr_state &= ~(UART_MCR_RTS | UART_MCR_DTR);
690
691 err = mxuport_set_mcr(port, mcr_state);
692 if (!err)
693 mxport->mcr_state = mcr_state;
694
695 mutex_unlock(&mxport->mutex);
696 }
697
mxuport_tiocmset(struct tty_struct * tty,unsigned int set,unsigned int clear)698 static int mxuport_tiocmset(struct tty_struct *tty, unsigned int set,
699 unsigned int clear)
700 {
701 struct usb_serial_port *port = tty->driver_data;
702 struct mxuport_port *mxport = usb_get_serial_port_data(port);
703 int err;
704 u8 mcr_state;
705
706 mutex_lock(&mxport->mutex);
707 mcr_state = mxport->mcr_state;
708
709 if (set & TIOCM_RTS)
710 mcr_state |= UART_MCR_RTS;
711
712 if (set & TIOCM_DTR)
713 mcr_state |= UART_MCR_DTR;
714
715 if (clear & TIOCM_RTS)
716 mcr_state &= ~UART_MCR_RTS;
717
718 if (clear & TIOCM_DTR)
719 mcr_state &= ~UART_MCR_DTR;
720
721 err = mxuport_set_mcr(port, mcr_state);
722 if (!err)
723 mxport->mcr_state = mcr_state;
724
725 mutex_unlock(&mxport->mutex);
726
727 return err;
728 }
729
mxuport_tiocmget(struct tty_struct * tty)730 static int mxuport_tiocmget(struct tty_struct *tty)
731 {
732 struct mxuport_port *mxport;
733 struct usb_serial_port *port = tty->driver_data;
734 unsigned int result;
735 unsigned long flags;
736 unsigned int msr;
737 unsigned int mcr;
738
739 mxport = usb_get_serial_port_data(port);
740
741 mutex_lock(&mxport->mutex);
742 spin_lock_irqsave(&mxport->spinlock, flags);
743
744 msr = mxport->msr_state;
745 mcr = mxport->mcr_state;
746
747 spin_unlock_irqrestore(&mxport->spinlock, flags);
748 mutex_unlock(&mxport->mutex);
749
750 result = (((mcr & UART_MCR_DTR) ? TIOCM_DTR : 0) | /* 0x002 */
751 ((mcr & UART_MCR_RTS) ? TIOCM_RTS : 0) | /* 0x004 */
752 ((msr & UART_MSR_CTS) ? TIOCM_CTS : 0) | /* 0x020 */
753 ((msr & UART_MSR_DCD) ? TIOCM_CAR : 0) | /* 0x040 */
754 ((msr & UART_MSR_RI) ? TIOCM_RI : 0) | /* 0x080 */
755 ((msr & UART_MSR_DSR) ? TIOCM_DSR : 0)); /* 0x100 */
756
757 dev_dbg(&port->dev, "%s - 0x%04x\n", __func__, result);
758
759 return result;
760 }
761
mxuport_set_termios_flow(struct tty_struct * tty,const struct ktermios * old_termios,struct usb_serial_port * port,struct usb_serial * serial)762 static int mxuport_set_termios_flow(struct tty_struct *tty,
763 const struct ktermios *old_termios,
764 struct usb_serial_port *port,
765 struct usb_serial *serial)
766 {
767 u8 xon = START_CHAR(tty);
768 u8 xoff = STOP_CHAR(tty);
769 int enable;
770 int err;
771 u8 *buf;
772 u8 rts;
773
774 buf = kmalloc(2, GFP_KERNEL);
775 if (!buf)
776 return -ENOMEM;
777
778 /* S/W flow control settings */
779 if (I_IXOFF(tty) || I_IXON(tty)) {
780 enable = 1;
781 buf[0] = xon;
782 buf[1] = xoff;
783
784 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_CHARS,
785 0, port->port_number,
786 buf, 2);
787 if (err)
788 goto out;
789
790 dev_dbg(&port->dev, "%s - XON = 0x%02x, XOFF = 0x%02x\n",
791 __func__, xon, xoff);
792 } else {
793 enable = 0;
794 }
795
796 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_XONXOFF,
797 enable, port->port_number);
798 if (err)
799 goto out;
800
801 rts = MX_RTS_NO_CHANGE;
802
803 /* H/W flow control settings */
804 if (!old_termios ||
805 C_CRTSCTS(tty) != (old_termios->c_cflag & CRTSCTS)) {
806 if (C_CRTSCTS(tty))
807 rts = MX_RTS_HW;
808 else
809 rts = MX_RTS_ENABLE;
810 }
811
812 if (C_BAUD(tty)) {
813 if (old_termios && (old_termios->c_cflag & CBAUD) == B0) {
814 /* Raise DTR and RTS */
815 if (C_CRTSCTS(tty))
816 rts = MX_RTS_HW;
817 else
818 rts = MX_RTS_ENABLE;
819 mxuport_set_dtr(port, 1);
820 }
821 } else {
822 /* Drop DTR and RTS */
823 rts = MX_RTS_DISABLE;
824 mxuport_set_dtr(port, 0);
825 }
826
827 if (rts != MX_RTS_NO_CHANGE)
828 err = mxuport_set_rts(port, rts);
829
830 out:
831 kfree(buf);
832 return err;
833 }
834
mxuport_set_termios(struct tty_struct * tty,struct usb_serial_port * port,const struct ktermios * old_termios)835 static void mxuport_set_termios(struct tty_struct *tty,
836 struct usb_serial_port *port,
837 const struct ktermios *old_termios)
838 {
839 struct usb_serial *serial = port->serial;
840 u8 *buf;
841 u8 data_bits;
842 u8 stop_bits;
843 u8 parity;
844 int baud;
845 int err;
846
847 if (old_termios &&
848 !tty_termios_hw_change(&tty->termios, old_termios) &&
849 tty->termios.c_iflag == old_termios->c_iflag) {
850 dev_dbg(&port->dev, "%s - nothing to change\n", __func__);
851 return;
852 }
853
854 buf = kmalloc(4, GFP_KERNEL);
855 if (!buf)
856 return;
857
858 /* Set data bit of termios */
859 switch (C_CSIZE(tty)) {
860 case CS5:
861 data_bits = MX_WORDLENGTH_5;
862 break;
863 case CS6:
864 data_bits = MX_WORDLENGTH_6;
865 break;
866 case CS7:
867 data_bits = MX_WORDLENGTH_7;
868 break;
869 case CS8:
870 default:
871 data_bits = MX_WORDLENGTH_8;
872 break;
873 }
874
875 /* Set parity of termios */
876 if (C_PARENB(tty)) {
877 if (C_CMSPAR(tty)) {
878 if (C_PARODD(tty))
879 parity = MX_PARITY_MARK;
880 else
881 parity = MX_PARITY_SPACE;
882 } else {
883 if (C_PARODD(tty))
884 parity = MX_PARITY_ODD;
885 else
886 parity = MX_PARITY_EVEN;
887 }
888 } else {
889 parity = MX_PARITY_NONE;
890 }
891
892 /* Set stop bit of termios */
893 if (C_CSTOPB(tty))
894 stop_bits = MX_STOP_BITS_2;
895 else
896 stop_bits = MX_STOP_BITS_1;
897
898 buf[0] = data_bits;
899 buf[1] = parity;
900 buf[2] = stop_bits;
901 buf[3] = 0;
902
903 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_LINE,
904 0, port->port_number, buf, 4);
905 if (err)
906 goto out;
907
908 err = mxuport_set_termios_flow(tty, old_termios, port, serial);
909 if (err)
910 goto out;
911
912 baud = tty_get_baud_rate(tty);
913 if (!baud)
914 baud = 9600;
915
916 /* Note: Little Endian */
917 put_unaligned_le32(baud, buf);
918
919 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_SET_BAUD,
920 0, port->port_number,
921 buf, 4);
922 if (err)
923 goto out;
924
925 dev_dbg(&port->dev, "baud_rate : %d\n", baud);
926 dev_dbg(&port->dev, "data_bits : %d\n", data_bits);
927 dev_dbg(&port->dev, "parity : %d\n", parity);
928 dev_dbg(&port->dev, "stop_bits : %d\n", stop_bits);
929
930 out:
931 kfree(buf);
932 }
933
934 /*
935 * Determine how many ports this device has dynamically. It will be
936 * called after the probe() callback is called, but before attach().
937 */
mxuport_calc_num_ports(struct usb_serial * serial,struct usb_serial_endpoints * epds)938 static int mxuport_calc_num_ports(struct usb_serial *serial,
939 struct usb_serial_endpoints *epds)
940 {
941 unsigned long features = (unsigned long)usb_get_serial_data(serial);
942 int num_ports;
943 int i;
944
945 if (features & MX_UPORT_2_PORT) {
946 num_ports = 2;
947 } else if (features & MX_UPORT_4_PORT) {
948 num_ports = 4;
949 } else if (features & MX_UPORT_8_PORT) {
950 num_ports = 8;
951 } else if (features & MX_UPORT_16_PORT) {
952 num_ports = 16;
953 } else {
954 dev_warn(&serial->interface->dev,
955 "unknown device, assuming two ports\n");
956 num_ports = 2;
957 }
958
959 /*
960 * Setup bulk-out endpoint multiplexing. All ports share the same
961 * bulk-out endpoint.
962 */
963 BUILD_BUG_ON(ARRAY_SIZE(epds->bulk_out) < 16);
964
965 for (i = 1; i < num_ports; ++i)
966 epds->bulk_out[i] = epds->bulk_out[0];
967
968 epds->num_bulk_out = num_ports;
969
970 return num_ports;
971 }
972
973 /* Get the version of the firmware currently running. */
mxuport_get_fw_version(struct usb_serial * serial,u32 * version)974 static int mxuport_get_fw_version(struct usb_serial *serial, u32 *version)
975 {
976 u8 *ver_buf;
977 int err;
978
979 ver_buf = kzalloc(4, GFP_KERNEL);
980 if (!ver_buf)
981 return -ENOMEM;
982
983 /* Get firmware version from SDRAM */
984 err = mxuport_recv_ctrl_urb(serial, RQ_VENDOR_GET_VERSION, 0, 0,
985 ver_buf, 4);
986 if (err != 4) {
987 err = -EIO;
988 goto out;
989 }
990
991 *version = (ver_buf[0] << 16) | (ver_buf[1] << 8) | ver_buf[2];
992 err = 0;
993 out:
994 kfree(ver_buf);
995 return err;
996 }
997
998 /* Given a firmware blob, download it to the device. */
mxuport_download_fw(struct usb_serial * serial,const struct firmware * fw_p)999 static int mxuport_download_fw(struct usb_serial *serial,
1000 const struct firmware *fw_p)
1001 {
1002 u8 *fw_buf;
1003 size_t txlen;
1004 size_t fwidx;
1005 int err;
1006
1007 fw_buf = kmalloc(DOWN_BLOCK_SIZE, GFP_KERNEL);
1008 if (!fw_buf)
1009 return -ENOMEM;
1010
1011 dev_dbg(&serial->interface->dev, "Starting firmware download...\n");
1012 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_START_FW_DOWN, 0, 0);
1013 if (err)
1014 goto out;
1015
1016 fwidx = 0;
1017 do {
1018 txlen = min_t(size_t, (fw_p->size - fwidx), DOWN_BLOCK_SIZE);
1019
1020 memcpy(fw_buf, &fw_p->data[fwidx], txlen);
1021 err = mxuport_send_ctrl_data_urb(serial, RQ_VENDOR_FW_DATA,
1022 0, 0, fw_buf, txlen);
1023 if (err) {
1024 mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN,
1025 0, 0);
1026 goto out;
1027 }
1028
1029 fwidx += txlen;
1030 usleep_range(1000, 2000);
1031
1032 } while (fwidx < fw_p->size);
1033
1034 msleep(1000);
1035 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_STOP_FW_DOWN, 0, 0);
1036 if (err)
1037 goto out;
1038
1039 msleep(1000);
1040 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_READY, 0, 0);
1041
1042 out:
1043 kfree(fw_buf);
1044 return err;
1045 }
1046
mxuport_probe(struct usb_serial * serial,const struct usb_device_id * id)1047 static int mxuport_probe(struct usb_serial *serial,
1048 const struct usb_device_id *id)
1049 {
1050 u16 productid = le16_to_cpu(serial->dev->descriptor.idProduct);
1051 const struct firmware *fw_p = NULL;
1052 u32 version;
1053 int local_ver;
1054 char buf[32];
1055 int err;
1056
1057 /* Load our firmware */
1058 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_QUERY_FW_CONFIG, 0, 0);
1059 if (err) {
1060 mxuport_send_ctrl_urb(serial, RQ_VENDOR_RESET_DEVICE, 0, 0);
1061 return err;
1062 }
1063
1064 err = mxuport_get_fw_version(serial, &version);
1065 if (err < 0)
1066 return err;
1067
1068 dev_dbg(&serial->interface->dev, "Device firmware version v%x.%x.%x\n",
1069 (version & 0xff0000) >> 16,
1070 (version & 0xff00) >> 8,
1071 (version & 0xff));
1072
1073 snprintf(buf, sizeof(buf) - 1, "moxa/moxa-%04x.fw", productid);
1074
1075 err = request_firmware(&fw_p, buf, &serial->interface->dev);
1076 if (err) {
1077 dev_warn(&serial->interface->dev, "Firmware %s not found\n",
1078 buf);
1079
1080 /* Use the firmware already in the device */
1081 err = 0;
1082 } else {
1083 local_ver = ((fw_p->data[VER_ADDR_1] << 16) |
1084 (fw_p->data[VER_ADDR_2] << 8) |
1085 fw_p->data[VER_ADDR_3]);
1086 dev_dbg(&serial->interface->dev,
1087 "Available firmware version v%x.%x.%x\n",
1088 fw_p->data[VER_ADDR_1], fw_p->data[VER_ADDR_2],
1089 fw_p->data[VER_ADDR_3]);
1090 if (local_ver > version) {
1091 err = mxuport_download_fw(serial, fw_p);
1092 if (err)
1093 goto out;
1094 err = mxuport_get_fw_version(serial, &version);
1095 if (err < 0)
1096 goto out;
1097 }
1098 }
1099
1100 dev_info(&serial->interface->dev,
1101 "Using device firmware version v%x.%x.%x\n",
1102 (version & 0xff0000) >> 16,
1103 (version & 0xff00) >> 8,
1104 (version & 0xff));
1105
1106 /*
1107 * Contains the features of this hardware. Store away for
1108 * later use, eg, number of ports.
1109 */
1110 usb_set_serial_data(serial, (void *)id->driver_info);
1111 out:
1112 if (fw_p)
1113 release_firmware(fw_p);
1114 return err;
1115 }
1116
1117
mxuport_port_probe(struct usb_serial_port * port)1118 static int mxuport_port_probe(struct usb_serial_port *port)
1119 {
1120 struct usb_serial *serial = port->serial;
1121 struct mxuport_port *mxport;
1122 int err;
1123
1124 mxport = devm_kzalloc(&port->dev, sizeof(struct mxuport_port),
1125 GFP_KERNEL);
1126 if (!mxport)
1127 return -ENOMEM;
1128
1129 mutex_init(&mxport->mutex);
1130 spin_lock_init(&mxport->spinlock);
1131
1132 /* Set the port private data */
1133 usb_set_serial_port_data(port, mxport);
1134
1135 /* Set FIFO (Enable) */
1136 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_FIFO_DISABLE,
1137 0, port->port_number);
1138 if (err)
1139 return err;
1140
1141 /* Set transmission mode (Hi-Performance) */
1142 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_HIGH_PERFOR,
1143 0, port->port_number);
1144 if (err)
1145 return err;
1146
1147 /* Set interface (RS-232) */
1148 return mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_INTERFACE,
1149 MX_INT_RS232,
1150 port->port_number);
1151 }
1152
mxuport_attach(struct usb_serial * serial)1153 static int mxuport_attach(struct usb_serial *serial)
1154 {
1155 struct usb_serial_port *port0 = serial->port[0];
1156 struct usb_serial_port *port1 = serial->port[1];
1157 int err;
1158
1159 /*
1160 * All data from the ports is received on the first bulk in
1161 * endpoint, with a multiplex header. The second bulk in is
1162 * used for events.
1163 *
1164 * Start to read from the device.
1165 */
1166 err = usb_serial_generic_submit_read_urbs(port0, GFP_KERNEL);
1167 if (err)
1168 return err;
1169
1170 err = usb_serial_generic_submit_read_urbs(port1, GFP_KERNEL);
1171 if (err) {
1172 usb_serial_generic_close(port0);
1173 return err;
1174 }
1175
1176 return 0;
1177 }
1178
mxuport_release(struct usb_serial * serial)1179 static void mxuport_release(struct usb_serial *serial)
1180 {
1181 struct usb_serial_port *port0 = serial->port[0];
1182 struct usb_serial_port *port1 = serial->port[1];
1183
1184 usb_serial_generic_close(port1);
1185 usb_serial_generic_close(port0);
1186 }
1187
mxuport_open(struct tty_struct * tty,struct usb_serial_port * port)1188 static int mxuport_open(struct tty_struct *tty, struct usb_serial_port *port)
1189 {
1190 struct mxuport_port *mxport = usb_get_serial_port_data(port);
1191 struct usb_serial *serial = port->serial;
1192 int err;
1193
1194 /* Set receive host (enable) */
1195 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
1196 1, port->port_number);
1197 if (err)
1198 return err;
1199
1200 err = mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN,
1201 1, port->port_number);
1202 if (err) {
1203 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN,
1204 0, port->port_number);
1205 return err;
1206 }
1207
1208 /* Initial port termios */
1209 if (tty)
1210 mxuport_set_termios(tty, port, NULL);
1211
1212 /*
1213 * TODO: use RQ_VENDOR_GET_MSR, once we know what it
1214 * returns.
1215 */
1216 mxport->msr_state = 0;
1217
1218 return err;
1219 }
1220
mxuport_close(struct usb_serial_port * port)1221 static void mxuport_close(struct usb_serial_port *port)
1222 {
1223 struct usb_serial *serial = port->serial;
1224
1225 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_OPEN, 0,
1226 port->port_number);
1227
1228 mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_RX_HOST_EN, 0,
1229 port->port_number);
1230 }
1231
1232 /* Send a break to the port. */
mxuport_break_ctl(struct tty_struct * tty,int break_state)1233 static int mxuport_break_ctl(struct tty_struct *tty, int break_state)
1234 {
1235 struct usb_serial_port *port = tty->driver_data;
1236 struct usb_serial *serial = port->serial;
1237 int enable;
1238
1239 if (break_state == -1) {
1240 enable = 1;
1241 dev_dbg(&port->dev, "%s - sending break\n", __func__);
1242 } else {
1243 enable = 0;
1244 dev_dbg(&port->dev, "%s - clearing break\n", __func__);
1245 }
1246
1247 return mxuport_send_ctrl_urb(serial, RQ_VENDOR_SET_BREAK,
1248 enable, port->port_number);
1249 }
1250
mxuport_resume(struct usb_serial * serial)1251 static int mxuport_resume(struct usb_serial *serial)
1252 {
1253 struct usb_serial_port *port;
1254 int c = 0;
1255 int i;
1256 int r;
1257
1258 for (i = 0; i < 2; i++) {
1259 port = serial->port[i];
1260
1261 r = usb_serial_generic_submit_read_urbs(port, GFP_NOIO);
1262 if (r < 0)
1263 c++;
1264 }
1265
1266 for (i = 0; i < serial->num_ports; i++) {
1267 port = serial->port[i];
1268 if (!tty_port_initialized(&port->port))
1269 continue;
1270
1271 r = usb_serial_generic_write_start(port, GFP_NOIO);
1272 if (r < 0)
1273 c++;
1274 }
1275
1276 return c ? -EIO : 0;
1277 }
1278
1279 static struct usb_serial_driver mxuport_device = {
1280 .driver = {
1281 .owner = THIS_MODULE,
1282 .name = "mxuport",
1283 },
1284 .description = "MOXA UPort",
1285 .id_table = mxuport_idtable,
1286 .num_bulk_in = 2,
1287 .num_bulk_out = 1,
1288 .probe = mxuport_probe,
1289 .port_probe = mxuport_port_probe,
1290 .attach = mxuport_attach,
1291 .release = mxuport_release,
1292 .calc_num_ports = mxuport_calc_num_ports,
1293 .open = mxuport_open,
1294 .close = mxuport_close,
1295 .set_termios = mxuport_set_termios,
1296 .break_ctl = mxuport_break_ctl,
1297 .tx_empty = mxuport_tx_empty,
1298 .tiocmiwait = usb_serial_generic_tiocmiwait,
1299 .get_icount = usb_serial_generic_get_icount,
1300 .throttle = mxuport_throttle,
1301 .unthrottle = mxuport_unthrottle,
1302 .tiocmget = mxuport_tiocmget,
1303 .tiocmset = mxuport_tiocmset,
1304 .dtr_rts = mxuport_dtr_rts,
1305 .process_read_urb = mxuport_process_read_urb,
1306 .prepare_write_buffer = mxuport_prepare_write_buffer,
1307 .resume = mxuport_resume,
1308 };
1309
1310 static struct usb_serial_driver *const serial_drivers[] = {
1311 &mxuport_device, NULL
1312 };
1313
1314 module_usb_serial_driver(serial_drivers, mxuport_idtable);
1315
1316 MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>");
1317 MODULE_AUTHOR("<support@moxa.com>");
1318 MODULE_LICENSE("GPL");
1319