1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Clean ups from Moschip version and a few ioctl implementations by: 4 * Paul B Schroeder <pschroeder "at" uplogix "dot" com> 5 * 6 * Originally based on drivers/usb/serial/io_edgeport.c which is: 7 * Copyright (C) 2000 Inside Out Networks, All rights reserved. 8 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com> 9 * 10 */ 11 12 #include <linux/kernel.h> 13 #include <linux/errno.h> 14 #include <linux/slab.h> 15 #include <linux/tty.h> 16 #include <linux/tty_driver.h> 17 #include <linux/tty_flip.h> 18 #include <linux/module.h> 19 #include <linux/serial.h> 20 #include <linux/usb.h> 21 #include <linux/usb/serial.h> 22 #include <linux/uaccess.h> 23 24 #define DRIVER_DESC "Moschip 7840/7820 USB Serial Driver" 25 26 /* 27 * 16C50 UART register defines 28 */ 29 30 #define LCR_BITS_5 0x00 /* 5 bits/char */ 31 #define LCR_BITS_6 0x01 /* 6 bits/char */ 32 #define LCR_BITS_7 0x02 /* 7 bits/char */ 33 #define LCR_BITS_8 0x03 /* 8 bits/char */ 34 #define LCR_BITS_MASK 0x03 /* Mask for bits/char field */ 35 36 #define LCR_STOP_1 0x00 /* 1 stop bit */ 37 #define LCR_STOP_1_5 0x04 /* 1.5 stop bits (if 5 bits/char) */ 38 #define LCR_STOP_2 0x04 /* 2 stop bits (if 6-8 bits/char) */ 39 #define LCR_STOP_MASK 0x04 /* Mask for stop bits field */ 40 41 #define LCR_PAR_NONE 0x00 /* No parity */ 42 #define LCR_PAR_ODD 0x08 /* Odd parity */ 43 #define LCR_PAR_EVEN 0x18 /* Even parity */ 44 #define LCR_PAR_MARK 0x28 /* Force parity bit to 1 */ 45 #define LCR_PAR_SPACE 0x38 /* Force parity bit to 0 */ 46 #define LCR_PAR_MASK 0x38 /* Mask for parity field */ 47 48 #define LCR_SET_BREAK 0x40 /* Set Break condition */ 49 #define LCR_DL_ENABLE 0x80 /* Enable access to divisor latch */ 50 51 #define MCR_DTR 0x01 /* Assert DTR */ 52 #define MCR_RTS 0x02 /* Assert RTS */ 53 #define MCR_OUT1 0x04 /* Loopback only: Sets state of RI */ 54 #define MCR_MASTER_IE 0x08 /* Enable interrupt outputs */ 55 #define MCR_LOOPBACK 0x10 /* Set internal (digital) loopback mode */ 56 #define MCR_XON_ANY 0x20 /* Enable any char to exit XOFF mode */ 57 58 #define MOS7840_MSR_CTS 0x10 /* Current state of CTS */ 59 #define MOS7840_MSR_DSR 0x20 /* Current state of DSR */ 60 #define MOS7840_MSR_RI 0x40 /* Current state of RI */ 61 #define MOS7840_MSR_CD 0x80 /* Current state of CD */ 62 63 /* 64 * Defines used for sending commands to port 65 */ 66 67 #define MOS_WDR_TIMEOUT 5000 /* default urb timeout */ 68 69 #define MOS_PORT1 0x0200 70 #define MOS_PORT2 0x0300 71 #define MOS_VENREG 0x0000 72 #define MOS_MAX_PORT 0x02 73 #define MOS_WRITE 0x0E 74 #define MOS_READ 0x0D 75 76 /* Requests */ 77 #define MCS_RD_RTYPE 0xC0 78 #define MCS_WR_RTYPE 0x40 79 #define MCS_RDREQ 0x0D 80 #define MCS_WRREQ 0x0E 81 #define MCS_CTRL_TIMEOUT 500 82 #define VENDOR_READ_LENGTH (0x01) 83 84 #define MAX_NAME_LEN 64 85 86 #define ZLP_REG1 0x3A /* Zero_Flag_Reg1 58 */ 87 #define ZLP_REG5 0x3E /* Zero_Flag_Reg5 62 */ 88 89 /* For higher baud Rates use TIOCEXBAUD */ 90 #define TIOCEXBAUD 0x5462 91 92 /* 93 * Vendor id and device id defines 94 * 95 * NOTE: Do not add new defines, add entries directly to the id_table instead. 96 */ 97 #define USB_VENDOR_ID_BANDB 0x0856 98 #define BANDB_DEVICE_ID_USO9ML2_2 0xAC22 99 #define BANDB_DEVICE_ID_USO9ML2_2P 0xBC00 100 #define BANDB_DEVICE_ID_USO9ML2_4 0xAC24 101 #define BANDB_DEVICE_ID_USO9ML2_4P 0xBC01 102 #define BANDB_DEVICE_ID_US9ML2_2 0xAC29 103 #define BANDB_DEVICE_ID_US9ML2_4 0xAC30 104 #define BANDB_DEVICE_ID_USPTL4_2 0xAC31 105 #define BANDB_DEVICE_ID_USPTL4_4 0xAC32 106 #define BANDB_DEVICE_ID_USOPTL4_2 0xAC42 107 #define BANDB_DEVICE_ID_USOPTL4_2P 0xBC02 108 #define BANDB_DEVICE_ID_USOPTL4_4 0xAC44 109 #define BANDB_DEVICE_ID_USOPTL4_4P 0xBC03 110 #define BANDB_DEVICE_ID_USOPTL2_4 0xAC24 111 112 /* Interrupt Routine Defines */ 113 114 #define SERIAL_IIR_RLS 0x06 115 #define SERIAL_IIR_MS 0x00 116 117 /* 118 * Emulation of the bit mask on the LINE STATUS REGISTER. 119 */ 120 #define SERIAL_LSR_DR 0x0001 121 #define SERIAL_LSR_OE 0x0002 122 #define SERIAL_LSR_PE 0x0004 123 #define SERIAL_LSR_FE 0x0008 124 #define SERIAL_LSR_BI 0x0010 125 126 #define MOS_MSR_DELTA_CTS 0x10 127 #define MOS_MSR_DELTA_DSR 0x20 128 #define MOS_MSR_DELTA_RI 0x40 129 #define MOS_MSR_DELTA_CD 0x80 130 131 /* Serial Port register Address */ 132 #define INTERRUPT_ENABLE_REGISTER ((__u16)(0x01)) 133 #define FIFO_CONTROL_REGISTER ((__u16)(0x02)) 134 #define LINE_CONTROL_REGISTER ((__u16)(0x03)) 135 #define MODEM_CONTROL_REGISTER ((__u16)(0x04)) 136 #define LINE_STATUS_REGISTER ((__u16)(0x05)) 137 #define MODEM_STATUS_REGISTER ((__u16)(0x06)) 138 #define SCRATCH_PAD_REGISTER ((__u16)(0x07)) 139 #define DIVISOR_LATCH_LSB ((__u16)(0x00)) 140 #define DIVISOR_LATCH_MSB ((__u16)(0x01)) 141 142 #define CLK_MULTI_REGISTER ((__u16)(0x02)) 143 #define CLK_START_VALUE_REGISTER ((__u16)(0x03)) 144 #define GPIO_REGISTER ((__u16)(0x07)) 145 146 #define SERIAL_LCR_DLAB ((__u16)(0x0080)) 147 148 /* 149 * URB POOL related defines 150 */ 151 #define NUM_URBS 16 /* URB Count */ 152 #define URB_TRANSFER_BUFFER_SIZE 32 /* URB Size */ 153 154 /* LED on/off milliseconds*/ 155 #define LED_ON_MS 500 156 #define LED_OFF_MS 500 157 158 enum mos7840_flag { 159 MOS7840_FLAG_LED_BUSY, 160 }; 161 162 #define MCS_PORT_MASK GENMASK(2, 0) 163 #define MCS_PORTS(nr) ((nr) & MCS_PORT_MASK) 164 #define MCS_LED BIT(3) 165 166 #define MCS_DEVICE(vid, pid, flags) \ 167 USB_DEVICE((vid), (pid)), .driver_info = (flags) 168 169 static const struct usb_device_id id_table[] = { 170 { MCS_DEVICE(0x0557, 0x2011, MCS_PORTS(4)) }, /* ATEN UC2324 */ 171 { MCS_DEVICE(0x0557, 0x7820, MCS_PORTS(2)) }, /* ATEN UC2322 */ 172 { MCS_DEVICE(0x110a, 0x2210, MCS_PORTS(2)) }, /* Moxa UPort 2210 */ 173 { MCS_DEVICE(0x9710, 0x7810, MCS_PORTS(1) | MCS_LED) }, /* ASIX MCS7810 */ 174 { MCS_DEVICE(0x9710, 0x7820, MCS_PORTS(2)) }, /* MosChip MCS7820 */ 175 { MCS_DEVICE(0x9710, 0x7840, MCS_PORTS(4)) }, /* MosChip MCS7840 */ 176 { MCS_DEVICE(0x9710, 0x7843, MCS_PORTS(3)) }, /* ASIX MCS7840 3 port */ 177 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2) }, 178 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_2P) }, 179 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4) }, 180 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USO9ML2_4P) }, 181 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_2) }, 182 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_US9ML2_4) }, 183 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_2) }, 184 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USPTL4_4) }, 185 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2) }, 186 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_2P) }, 187 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4) }, 188 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL4_4P) }, 189 { USB_DEVICE(USB_VENDOR_ID_BANDB, BANDB_DEVICE_ID_USOPTL2_4) }, 190 {} /* terminating entry */ 191 }; 192 MODULE_DEVICE_TABLE(usb, id_table); 193 194 /* This structure holds all of the local port information */ 195 196 struct moschip_port { 197 int port_num; /*Actual port number in the device(1,2,etc) */ 198 struct urb *read_urb; /* read URB for this port */ 199 __u8 shadowLCR; /* last LCR value received */ 200 __u8 shadowMCR; /* last MCR value received */ 201 struct usb_serial_port *port; /* loop back to the owner of this object */ 202 203 /* Offsets */ 204 __u8 SpRegOffset; 205 __u8 ControlRegOffset; 206 __u8 DcrRegOffset; 207 208 spinlock_t pool_lock; 209 struct urb *write_urb_pool[NUM_URBS]; 210 char busy[NUM_URBS]; 211 bool read_urb_busy; 212 213 /* For device(s) with LED indicator */ 214 bool has_led; 215 struct timer_list led_timer1; /* Timer for LED on */ 216 struct timer_list led_timer2; /* Timer for LED off */ 217 struct urb *led_urb; 218 struct usb_ctrlrequest *led_dr; 219 220 unsigned long flags; 221 }; 222 223 /* 224 * mos7840_set_reg_sync 225 * To set the Control register by calling usb_fill_control_urb function 226 * by passing usb_sndctrlpipe function as parameter. 227 */ 228 229 static int mos7840_set_reg_sync(struct usb_serial_port *port, __u16 reg, 230 __u16 val) 231 { 232 struct usb_device *dev = port->serial->dev; 233 val = val & 0x00ff; 234 dev_dbg(&port->dev, "mos7840_set_reg_sync offset is %x, value %x\n", reg, val); 235 236 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ, 237 MCS_WR_RTYPE, val, reg, NULL, 0, 238 MOS_WDR_TIMEOUT); 239 } 240 241 /* 242 * mos7840_get_reg_sync 243 * To set the Uart register by calling usb_fill_control_urb function by 244 * passing usb_rcvctrlpipe function as parameter. 245 */ 246 247 static int mos7840_get_reg_sync(struct usb_serial_port *port, __u16 reg, 248 __u16 *val) 249 { 250 struct usb_device *dev = port->serial->dev; 251 int ret = 0; 252 u8 *buf; 253 254 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL); 255 if (!buf) 256 return -ENOMEM; 257 258 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ, 259 MCS_RD_RTYPE, 0, reg, buf, VENDOR_READ_LENGTH, 260 MOS_WDR_TIMEOUT); 261 if (ret < VENDOR_READ_LENGTH) { 262 if (ret >= 0) 263 ret = -EIO; 264 goto out; 265 } 266 267 *val = buf[0]; 268 dev_dbg(&port->dev, "%s offset is %x, return val %x\n", __func__, reg, *val); 269 out: 270 kfree(buf); 271 return ret; 272 } 273 274 /* 275 * mos7840_set_uart_reg 276 * To set the Uart register by calling usb_fill_control_urb function by 277 * passing usb_sndctrlpipe function as parameter. 278 */ 279 280 static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg, 281 __u16 val) 282 { 283 284 struct usb_device *dev = port->serial->dev; 285 val = val & 0x00ff; 286 /* For the UART control registers, the application number need 287 to be Or'ed */ 288 if (port->serial->num_ports == 2 && port->port_number != 0) 289 val |= ((__u16)port->port_number + 2) << 8; 290 else 291 val |= ((__u16)port->port_number + 1) << 8; 292 dev_dbg(&port->dev, "%s application number is %x\n", __func__, val); 293 return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ, 294 MCS_WR_RTYPE, val, reg, NULL, 0, 295 MOS_WDR_TIMEOUT); 296 297 } 298 299 /* 300 * mos7840_get_uart_reg 301 * To set the Control register by calling usb_fill_control_urb function 302 * by passing usb_rcvctrlpipe function as parameter. 303 */ 304 static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg, 305 __u16 *val) 306 { 307 struct usb_device *dev = port->serial->dev; 308 int ret = 0; 309 __u16 Wval; 310 u8 *buf; 311 312 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL); 313 if (!buf) 314 return -ENOMEM; 315 316 /* Wval is same as application number */ 317 if (port->serial->num_ports == 2 && port->port_number != 0) 318 Wval = ((__u16)port->port_number + 2) << 8; 319 else 320 Wval = ((__u16)port->port_number + 1) << 8; 321 dev_dbg(&port->dev, "%s application number is %x\n", __func__, Wval); 322 ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ, 323 MCS_RD_RTYPE, Wval, reg, buf, VENDOR_READ_LENGTH, 324 MOS_WDR_TIMEOUT); 325 if (ret < VENDOR_READ_LENGTH) { 326 if (ret >= 0) 327 ret = -EIO; 328 goto out; 329 } 330 *val = buf[0]; 331 out: 332 kfree(buf); 333 return ret; 334 } 335 336 static void mos7840_dump_serial_port(struct usb_serial_port *port, 337 struct moschip_port *mos7840_port) 338 { 339 340 dev_dbg(&port->dev, "SpRegOffset is %2x\n", mos7840_port->SpRegOffset); 341 dev_dbg(&port->dev, "ControlRegOffset is %2x\n", mos7840_port->ControlRegOffset); 342 dev_dbg(&port->dev, "DCRRegOffset is %2x\n", mos7840_port->DcrRegOffset); 343 344 } 345 346 /************************************************************************/ 347 /************************************************************************/ 348 /* U S B C A L L B A C K F U N C T I O N S */ 349 /* U S B C A L L B A C K F U N C T I O N S */ 350 /************************************************************************/ 351 /************************************************************************/ 352 353 static void mos7840_set_led_callback(struct urb *urb) 354 { 355 switch (urb->status) { 356 case 0: 357 /* Success */ 358 break; 359 case -ECONNRESET: 360 case -ENOENT: 361 case -ESHUTDOWN: 362 /* This urb is terminated, clean up */ 363 dev_dbg(&urb->dev->dev, "%s - urb shutting down: %d\n", 364 __func__, urb->status); 365 break; 366 default: 367 dev_dbg(&urb->dev->dev, "%s - nonzero urb status: %d\n", 368 __func__, urb->status); 369 } 370 } 371 372 static void mos7840_set_led_async(struct moschip_port *mcs, __u16 wval, 373 __u16 reg) 374 { 375 struct usb_device *dev = mcs->port->serial->dev; 376 struct usb_ctrlrequest *dr = mcs->led_dr; 377 378 dr->bRequestType = MCS_WR_RTYPE; 379 dr->bRequest = MCS_WRREQ; 380 dr->wValue = cpu_to_le16(wval); 381 dr->wIndex = cpu_to_le16(reg); 382 dr->wLength = cpu_to_le16(0); 383 384 usb_fill_control_urb(mcs->led_urb, dev, usb_sndctrlpipe(dev, 0), 385 (unsigned char *)dr, NULL, 0, mos7840_set_led_callback, NULL); 386 387 usb_submit_urb(mcs->led_urb, GFP_ATOMIC); 388 } 389 390 static void mos7840_set_led_sync(struct usb_serial_port *port, __u16 reg, 391 __u16 val) 392 { 393 struct usb_device *dev = port->serial->dev; 394 395 usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ, MCS_WR_RTYPE, 396 val, reg, NULL, 0, MOS_WDR_TIMEOUT); 397 } 398 399 static void mos7840_led_off(struct timer_list *t) 400 { 401 struct moschip_port *mcs = from_timer(mcs, t, led_timer1); 402 403 /* Turn off LED */ 404 mos7840_set_led_async(mcs, 0x0300, MODEM_CONTROL_REGISTER); 405 mod_timer(&mcs->led_timer2, 406 jiffies + msecs_to_jiffies(LED_OFF_MS)); 407 } 408 409 static void mos7840_led_flag_off(struct timer_list *t) 410 { 411 struct moschip_port *mcs = from_timer(mcs, t, led_timer2); 412 413 clear_bit_unlock(MOS7840_FLAG_LED_BUSY, &mcs->flags); 414 } 415 416 static void mos7840_led_activity(struct usb_serial_port *port) 417 { 418 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 419 420 if (test_and_set_bit_lock(MOS7840_FLAG_LED_BUSY, &mos7840_port->flags)) 421 return; 422 423 mos7840_set_led_async(mos7840_port, 0x0301, MODEM_CONTROL_REGISTER); 424 mod_timer(&mos7840_port->led_timer1, 425 jiffies + msecs_to_jiffies(LED_ON_MS)); 426 } 427 428 /***************************************************************************** 429 * mos7840_bulk_in_callback 430 * this is the callback function for when we have received data on the 431 * bulk in endpoint. 432 *****************************************************************************/ 433 434 static void mos7840_bulk_in_callback(struct urb *urb) 435 { 436 struct moschip_port *mos7840_port = urb->context; 437 struct usb_serial_port *port = mos7840_port->port; 438 int retval; 439 unsigned char *data; 440 int status = urb->status; 441 442 if (status) { 443 dev_dbg(&urb->dev->dev, "nonzero read bulk status received: %d\n", status); 444 mos7840_port->read_urb_busy = false; 445 return; 446 } 447 448 data = urb->transfer_buffer; 449 usb_serial_debug_data(&port->dev, __func__, urb->actual_length, data); 450 451 if (urb->actual_length) { 452 struct tty_port *tport = &mos7840_port->port->port; 453 tty_insert_flip_string(tport, data, urb->actual_length); 454 tty_flip_buffer_push(tport); 455 port->icount.rx += urb->actual_length; 456 dev_dbg(&port->dev, "icount.rx is %d:\n", port->icount.rx); 457 } 458 459 if (mos7840_port->has_led) 460 mos7840_led_activity(port); 461 462 mos7840_port->read_urb_busy = true; 463 retval = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC); 464 465 if (retval) { 466 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, retval = %d\n", retval); 467 mos7840_port->read_urb_busy = false; 468 } 469 } 470 471 /***************************************************************************** 472 * mos7840_bulk_out_data_callback 473 * this is the callback function for when we have finished sending 474 * serial data on the bulk out endpoint. 475 *****************************************************************************/ 476 477 static void mos7840_bulk_out_data_callback(struct urb *urb) 478 { 479 struct moschip_port *mos7840_port = urb->context; 480 struct usb_serial_port *port = mos7840_port->port; 481 int status = urb->status; 482 unsigned long flags; 483 int i; 484 485 spin_lock_irqsave(&mos7840_port->pool_lock, flags); 486 for (i = 0; i < NUM_URBS; i++) { 487 if (urb == mos7840_port->write_urb_pool[i]) { 488 mos7840_port->busy[i] = 0; 489 break; 490 } 491 } 492 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); 493 494 if (status) { 495 dev_dbg(&port->dev, "nonzero write bulk status received:%d\n", status); 496 return; 497 } 498 499 tty_port_tty_wakeup(&port->port); 500 501 } 502 503 /************************************************************************/ 504 /* D R I V E R T T Y I N T E R F A C E F U N C T I O N S */ 505 /************************************************************************/ 506 507 /***************************************************************************** 508 * mos7840_open 509 * this function is called by the tty driver when a port is opened 510 * If successful, we return 0 511 * Otherwise we return a negative error number. 512 *****************************************************************************/ 513 514 static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port) 515 { 516 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 517 struct usb_serial *serial = port->serial; 518 int response; 519 int j; 520 struct urb *urb; 521 __u16 Data; 522 int status; 523 524 usb_clear_halt(serial->dev, port->write_urb->pipe); 525 usb_clear_halt(serial->dev, port->read_urb->pipe); 526 527 /* Initialising the write urb pool */ 528 for (j = 0; j < NUM_URBS; ++j) { 529 urb = usb_alloc_urb(0, GFP_KERNEL); 530 mos7840_port->write_urb_pool[j] = urb; 531 if (!urb) 532 continue; 533 534 urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, 535 GFP_KERNEL); 536 if (!urb->transfer_buffer) { 537 usb_free_urb(urb); 538 mos7840_port->write_urb_pool[j] = NULL; 539 continue; 540 } 541 } 542 543 /***************************************************************************** 544 * Initialize MCS7840 -- Write Init values to corresponding Registers 545 * 546 * Register Index 547 * 1 : IER 548 * 2 : FCR 549 * 3 : LCR 550 * 4 : MCR 551 * 552 * 0x08 : SP1/2 Control Reg 553 *****************************************************************************/ 554 555 /* NEED to check the following Block */ 556 557 Data = 0x0; 558 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data); 559 if (status < 0) { 560 dev_dbg(&port->dev, "Reading Spreg failed\n"); 561 goto err; 562 } 563 Data |= 0x80; 564 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data); 565 if (status < 0) { 566 dev_dbg(&port->dev, "writing Spreg failed\n"); 567 goto err; 568 } 569 570 Data &= ~0x80; 571 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data); 572 if (status < 0) { 573 dev_dbg(&port->dev, "writing Spreg failed\n"); 574 goto err; 575 } 576 /* End of block to be checked */ 577 578 Data = 0x0; 579 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset, 580 &Data); 581 if (status < 0) { 582 dev_dbg(&port->dev, "Reading Controlreg failed\n"); 583 goto err; 584 } 585 Data |= 0x08; /* Driver done bit */ 586 Data |= 0x20; /* rx_disable */ 587 status = mos7840_set_reg_sync(port, 588 mos7840_port->ControlRegOffset, Data); 589 if (status < 0) { 590 dev_dbg(&port->dev, "writing Controlreg failed\n"); 591 goto err; 592 } 593 /* do register settings here */ 594 /* Set all regs to the device default values. */ 595 /*********************************** 596 * First Disable all interrupts. 597 ***********************************/ 598 Data = 0x00; 599 status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); 600 if (status < 0) { 601 dev_dbg(&port->dev, "disabling interrupts failed\n"); 602 goto err; 603 } 604 /* Set FIFO_CONTROL_REGISTER to the default value */ 605 Data = 0x00; 606 status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); 607 if (status < 0) { 608 dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n"); 609 goto err; 610 } 611 612 Data = 0xcf; 613 status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); 614 if (status < 0) { 615 dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER failed\n"); 616 goto err; 617 } 618 619 Data = 0x03; 620 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); 621 mos7840_port->shadowLCR = Data; 622 623 Data = 0x0b; 624 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); 625 mos7840_port->shadowMCR = Data; 626 627 Data = 0x00; 628 status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); 629 mos7840_port->shadowLCR = Data; 630 631 Data |= SERIAL_LCR_DLAB; /* data latch enable in LCR 0x80 */ 632 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); 633 634 Data = 0x0c; 635 status = mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data); 636 637 Data = 0x0; 638 status = mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data); 639 640 Data = 0x00; 641 status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data); 642 643 Data = Data & ~SERIAL_LCR_DLAB; 644 status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); 645 mos7840_port->shadowLCR = Data; 646 647 /* clearing Bulkin and Bulkout Fifo */ 648 Data = 0x0; 649 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data); 650 651 Data = Data | 0x0c; 652 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data); 653 654 Data = Data & ~0x0c; 655 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data); 656 /* Finally enable all interrupts */ 657 Data = 0x0c; 658 status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); 659 660 /* clearing rx_disable */ 661 Data = 0x0; 662 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset, 663 &Data); 664 Data = Data & ~0x20; 665 status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset, 666 Data); 667 668 /* rx_negate */ 669 Data = 0x0; 670 status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset, 671 &Data); 672 Data = Data | 0x10; 673 status = mos7840_set_reg_sync(port, mos7840_port->ControlRegOffset, 674 Data); 675 676 dev_dbg(&port->dev, "port number is %d\n", port->port_number); 677 dev_dbg(&port->dev, "minor number is %d\n", port->minor); 678 dev_dbg(&port->dev, "Bulkin endpoint is %d\n", port->bulk_in_endpointAddress); 679 dev_dbg(&port->dev, "BulkOut endpoint is %d\n", port->bulk_out_endpointAddress); 680 dev_dbg(&port->dev, "Interrupt endpoint is %d\n", port->interrupt_in_endpointAddress); 681 dev_dbg(&port->dev, "port's number in the device is %d\n", mos7840_port->port_num); 682 mos7840_port->read_urb = port->read_urb; 683 684 /* set up our bulk in urb */ 685 if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) { 686 usb_fill_bulk_urb(mos7840_port->read_urb, 687 serial->dev, 688 usb_rcvbulkpipe(serial->dev, 689 (port->bulk_in_endpointAddress) + 2), 690 port->bulk_in_buffer, 691 mos7840_port->read_urb->transfer_buffer_length, 692 mos7840_bulk_in_callback, mos7840_port); 693 } else { 694 usb_fill_bulk_urb(mos7840_port->read_urb, 695 serial->dev, 696 usb_rcvbulkpipe(serial->dev, 697 port->bulk_in_endpointAddress), 698 port->bulk_in_buffer, 699 mos7840_port->read_urb->transfer_buffer_length, 700 mos7840_bulk_in_callback, mos7840_port); 701 } 702 703 dev_dbg(&port->dev, "%s: bulkin endpoint is %d\n", __func__, port->bulk_in_endpointAddress); 704 mos7840_port->read_urb_busy = true; 705 response = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL); 706 if (response) { 707 dev_err(&port->dev, "%s - Error %d submitting control urb\n", 708 __func__, response); 709 mos7840_port->read_urb_busy = false; 710 } 711 712 /* initialize our port settings */ 713 /* Must set to enable ints! */ 714 mos7840_port->shadowMCR = MCR_MASTER_IE; 715 716 return 0; 717 err: 718 for (j = 0; j < NUM_URBS; ++j) { 719 urb = mos7840_port->write_urb_pool[j]; 720 if (!urb) 721 continue; 722 kfree(urb->transfer_buffer); 723 usb_free_urb(urb); 724 } 725 return status; 726 } 727 728 /***************************************************************************** 729 * mos7840_chars_in_buffer 730 * this function is called by the tty driver when it wants to know how many 731 * bytes of data we currently have outstanding in the port (data that has 732 * been written, but hasn't made it out the port yet) 733 * If successful, we return the number of bytes left to be written in the 734 * system, 735 * Otherwise we return zero. 736 *****************************************************************************/ 737 738 static int mos7840_chars_in_buffer(struct tty_struct *tty) 739 { 740 struct usb_serial_port *port = tty->driver_data; 741 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 742 int i; 743 int chars = 0; 744 unsigned long flags; 745 746 spin_lock_irqsave(&mos7840_port->pool_lock, flags); 747 for (i = 0; i < NUM_URBS; ++i) { 748 if (mos7840_port->busy[i]) { 749 struct urb *urb = mos7840_port->write_urb_pool[i]; 750 chars += urb->transfer_buffer_length; 751 } 752 } 753 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); 754 dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars); 755 return chars; 756 757 } 758 759 /***************************************************************************** 760 * mos7840_close 761 * this function is called by the tty driver when a port is closed 762 *****************************************************************************/ 763 764 static void mos7840_close(struct usb_serial_port *port) 765 { 766 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 767 int j; 768 __u16 Data; 769 770 for (j = 0; j < NUM_URBS; ++j) 771 usb_kill_urb(mos7840_port->write_urb_pool[j]); 772 773 /* Freeing Write URBs */ 774 for (j = 0; j < NUM_URBS; ++j) { 775 if (mos7840_port->write_urb_pool[j]) { 776 kfree(mos7840_port->write_urb_pool[j]->transfer_buffer); 777 usb_free_urb(mos7840_port->write_urb_pool[j]); 778 } 779 } 780 781 usb_kill_urb(mos7840_port->read_urb); 782 mos7840_port->read_urb_busy = false; 783 784 Data = 0x0; 785 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); 786 787 Data = 0x00; 788 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); 789 } 790 791 /***************************************************************************** 792 * mos7840_break 793 * this function sends a break to the port 794 *****************************************************************************/ 795 static void mos7840_break(struct tty_struct *tty, int break_state) 796 { 797 struct usb_serial_port *port = tty->driver_data; 798 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 799 unsigned char data; 800 801 if (break_state == -1) 802 data = mos7840_port->shadowLCR | LCR_SET_BREAK; 803 else 804 data = mos7840_port->shadowLCR & ~LCR_SET_BREAK; 805 806 /* FIXME: no locking on shadowLCR anywhere in driver */ 807 mos7840_port->shadowLCR = data; 808 dev_dbg(&port->dev, "%s mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR); 809 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, 810 mos7840_port->shadowLCR); 811 } 812 813 /***************************************************************************** 814 * mos7840_write_room 815 * this function is called by the tty driver when it wants to know how many 816 * bytes of data we can accept for a specific port. 817 * If successful, we return the amount of room that we have for this port 818 * Otherwise we return a negative error number. 819 *****************************************************************************/ 820 821 static int mos7840_write_room(struct tty_struct *tty) 822 { 823 struct usb_serial_port *port = tty->driver_data; 824 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 825 int i; 826 int room = 0; 827 unsigned long flags; 828 829 spin_lock_irqsave(&mos7840_port->pool_lock, flags); 830 for (i = 0; i < NUM_URBS; ++i) { 831 if (!mos7840_port->busy[i]) 832 room += URB_TRANSFER_BUFFER_SIZE; 833 } 834 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); 835 836 room = (room == 0) ? 0 : room - URB_TRANSFER_BUFFER_SIZE + 1; 837 dev_dbg(&mos7840_port->port->dev, "%s - returns %d\n", __func__, room); 838 return room; 839 840 } 841 842 /***************************************************************************** 843 * mos7840_write 844 * this function is called by the tty driver when data should be written to 845 * the port. 846 * If successful, we return the number of bytes written, otherwise we 847 * return a negative error number. 848 *****************************************************************************/ 849 850 static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port, 851 const unsigned char *data, int count) 852 { 853 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 854 struct usb_serial *serial = port->serial; 855 int status; 856 int i; 857 int bytes_sent = 0; 858 int transfer_size; 859 unsigned long flags; 860 struct urb *urb; 861 /* __u16 Data; */ 862 const unsigned char *current_position = data; 863 864 /* try to find a free urb in the list */ 865 urb = NULL; 866 867 spin_lock_irqsave(&mos7840_port->pool_lock, flags); 868 for (i = 0; i < NUM_URBS; ++i) { 869 if (!mos7840_port->busy[i]) { 870 mos7840_port->busy[i] = 1; 871 urb = mos7840_port->write_urb_pool[i]; 872 dev_dbg(&port->dev, "URB:%d\n", i); 873 break; 874 } 875 } 876 spin_unlock_irqrestore(&mos7840_port->pool_lock, flags); 877 878 if (urb == NULL) { 879 dev_dbg(&port->dev, "%s - no more free urbs\n", __func__); 880 goto exit; 881 } 882 883 if (urb->transfer_buffer == NULL) { 884 urb->transfer_buffer = kmalloc(URB_TRANSFER_BUFFER_SIZE, 885 GFP_ATOMIC); 886 if (!urb->transfer_buffer) 887 goto exit; 888 } 889 transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE); 890 891 memcpy(urb->transfer_buffer, current_position, transfer_size); 892 893 /* fill urb with data and submit */ 894 if ((serial->num_ports == 2) && (((__u16)port->port_number % 2) != 0)) { 895 usb_fill_bulk_urb(urb, 896 serial->dev, 897 usb_sndbulkpipe(serial->dev, 898 (port->bulk_out_endpointAddress) + 2), 899 urb->transfer_buffer, 900 transfer_size, 901 mos7840_bulk_out_data_callback, mos7840_port); 902 } else { 903 usb_fill_bulk_urb(urb, 904 serial->dev, 905 usb_sndbulkpipe(serial->dev, 906 port->bulk_out_endpointAddress), 907 urb->transfer_buffer, 908 transfer_size, 909 mos7840_bulk_out_data_callback, mos7840_port); 910 } 911 912 dev_dbg(&port->dev, "bulkout endpoint is %d\n", port->bulk_out_endpointAddress); 913 914 if (mos7840_port->has_led) 915 mos7840_led_activity(port); 916 917 /* send it down the pipe */ 918 status = usb_submit_urb(urb, GFP_ATOMIC); 919 920 if (status) { 921 mos7840_port->busy[i] = 0; 922 dev_err_console(port, "%s - usb_submit_urb(write bulk) failed " 923 "with status = %d\n", __func__, status); 924 bytes_sent = status; 925 goto exit; 926 } 927 bytes_sent = transfer_size; 928 port->icount.tx += transfer_size; 929 dev_dbg(&port->dev, "icount.tx is %d:\n", port->icount.tx); 930 exit: 931 return bytes_sent; 932 933 } 934 935 /***************************************************************************** 936 * mos7840_throttle 937 * this function is called by the tty driver when it wants to stop the data 938 * being read from the port. 939 *****************************************************************************/ 940 941 static void mos7840_throttle(struct tty_struct *tty) 942 { 943 struct usb_serial_port *port = tty->driver_data; 944 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 945 int status; 946 947 /* if we are implementing XON/XOFF, send the stop character */ 948 if (I_IXOFF(tty)) { 949 unsigned char stop_char = STOP_CHAR(tty); 950 status = mos7840_write(tty, port, &stop_char, 1); 951 if (status <= 0) 952 return; 953 } 954 /* if we are implementing RTS/CTS, toggle that line */ 955 if (C_CRTSCTS(tty)) { 956 mos7840_port->shadowMCR &= ~MCR_RTS; 957 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, 958 mos7840_port->shadowMCR); 959 if (status < 0) 960 return; 961 } 962 } 963 964 /***************************************************************************** 965 * mos7840_unthrottle 966 * this function is called by the tty driver when it wants to resume 967 * the data being read from the port (called after mos7840_throttle is 968 * called) 969 *****************************************************************************/ 970 static void mos7840_unthrottle(struct tty_struct *tty) 971 { 972 struct usb_serial_port *port = tty->driver_data; 973 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 974 int status; 975 976 /* if we are implementing XON/XOFF, send the start character */ 977 if (I_IXOFF(tty)) { 978 unsigned char start_char = START_CHAR(tty); 979 status = mos7840_write(tty, port, &start_char, 1); 980 if (status <= 0) 981 return; 982 } 983 984 /* if we are implementing RTS/CTS, toggle that line */ 985 if (C_CRTSCTS(tty)) { 986 mos7840_port->shadowMCR |= MCR_RTS; 987 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, 988 mos7840_port->shadowMCR); 989 if (status < 0) 990 return; 991 } 992 } 993 994 static int mos7840_tiocmget(struct tty_struct *tty) 995 { 996 struct usb_serial_port *port = tty->driver_data; 997 unsigned int result; 998 __u16 msr; 999 __u16 mcr; 1000 int status; 1001 1002 status = mos7840_get_uart_reg(port, MODEM_STATUS_REGISTER, &msr); 1003 if (status < 0) 1004 return -EIO; 1005 status = mos7840_get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr); 1006 if (status < 0) 1007 return -EIO; 1008 result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0) 1009 | ((mcr & MCR_RTS) ? TIOCM_RTS : 0) 1010 | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0) 1011 | ((msr & MOS7840_MSR_CTS) ? TIOCM_CTS : 0) 1012 | ((msr & MOS7840_MSR_CD) ? TIOCM_CAR : 0) 1013 | ((msr & MOS7840_MSR_RI) ? TIOCM_RI : 0) 1014 | ((msr & MOS7840_MSR_DSR) ? TIOCM_DSR : 0); 1015 1016 dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result); 1017 1018 return result; 1019 } 1020 1021 static int mos7840_tiocmset(struct tty_struct *tty, 1022 unsigned int set, unsigned int clear) 1023 { 1024 struct usb_serial_port *port = tty->driver_data; 1025 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 1026 unsigned int mcr; 1027 int status; 1028 1029 /* FIXME: What locks the port registers ? */ 1030 mcr = mos7840_port->shadowMCR; 1031 if (clear & TIOCM_RTS) 1032 mcr &= ~MCR_RTS; 1033 if (clear & TIOCM_DTR) 1034 mcr &= ~MCR_DTR; 1035 if (clear & TIOCM_LOOP) 1036 mcr &= ~MCR_LOOPBACK; 1037 1038 if (set & TIOCM_RTS) 1039 mcr |= MCR_RTS; 1040 if (set & TIOCM_DTR) 1041 mcr |= MCR_DTR; 1042 if (set & TIOCM_LOOP) 1043 mcr |= MCR_LOOPBACK; 1044 1045 mos7840_port->shadowMCR = mcr; 1046 1047 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr); 1048 if (status < 0) { 1049 dev_dbg(&port->dev, "setting MODEM_CONTROL_REGISTER Failed\n"); 1050 return status; 1051 } 1052 1053 return 0; 1054 } 1055 1056 /***************************************************************************** 1057 * mos7840_calc_baud_rate_divisor 1058 * this function calculates the proper baud rate divisor for the specified 1059 * baud rate. 1060 *****************************************************************************/ 1061 static int mos7840_calc_baud_rate_divisor(struct usb_serial_port *port, 1062 int baudRate, int *divisor, 1063 __u16 *clk_sel_val) 1064 { 1065 dev_dbg(&port->dev, "%s - %d\n", __func__, baudRate); 1066 1067 if (baudRate <= 115200) { 1068 *divisor = 115200 / baudRate; 1069 *clk_sel_val = 0x0; 1070 } 1071 if ((baudRate > 115200) && (baudRate <= 230400)) { 1072 *divisor = 230400 / baudRate; 1073 *clk_sel_val = 0x10; 1074 } else if ((baudRate > 230400) && (baudRate <= 403200)) { 1075 *divisor = 403200 / baudRate; 1076 *clk_sel_val = 0x20; 1077 } else if ((baudRate > 403200) && (baudRate <= 460800)) { 1078 *divisor = 460800 / baudRate; 1079 *clk_sel_val = 0x30; 1080 } else if ((baudRate > 460800) && (baudRate <= 806400)) { 1081 *divisor = 806400 / baudRate; 1082 *clk_sel_val = 0x40; 1083 } else if ((baudRate > 806400) && (baudRate <= 921600)) { 1084 *divisor = 921600 / baudRate; 1085 *clk_sel_val = 0x50; 1086 } else if ((baudRate > 921600) && (baudRate <= 1572864)) { 1087 *divisor = 1572864 / baudRate; 1088 *clk_sel_val = 0x60; 1089 } else if ((baudRate > 1572864) && (baudRate <= 3145728)) { 1090 *divisor = 3145728 / baudRate; 1091 *clk_sel_val = 0x70; 1092 } 1093 return 0; 1094 } 1095 1096 /***************************************************************************** 1097 * mos7840_send_cmd_write_baud_rate 1098 * this function sends the proper command to change the baud rate of the 1099 * specified port. 1100 *****************************************************************************/ 1101 1102 static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port, 1103 int baudRate) 1104 { 1105 struct usb_serial_port *port = mos7840_port->port; 1106 int divisor = 0; 1107 int status; 1108 __u16 Data; 1109 __u16 clk_sel_val; 1110 1111 dev_dbg(&port->dev, "%s - baud = %d\n", __func__, baudRate); 1112 /* reset clk_uart_sel in spregOffset */ 1113 if (baudRate > 115200) { 1114 #ifdef HW_flow_control 1115 /* NOTE: need to see the pther register to modify */ 1116 /* setting h/w flow control bit to 1 */ 1117 Data = 0x2b; 1118 mos7840_port->shadowMCR = Data; 1119 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, 1120 Data); 1121 if (status < 0) { 1122 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n"); 1123 return -1; 1124 } 1125 #endif 1126 1127 } else { 1128 #ifdef HW_flow_control 1129 /* setting h/w flow control bit to 0 */ 1130 Data = 0xb; 1131 mos7840_port->shadowMCR = Data; 1132 status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, 1133 Data); 1134 if (status < 0) { 1135 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n"); 1136 return -1; 1137 } 1138 #endif 1139 1140 } 1141 1142 if (1) { /* baudRate <= 115200) */ 1143 clk_sel_val = 0x0; 1144 Data = 0x0; 1145 status = mos7840_calc_baud_rate_divisor(port, baudRate, &divisor, 1146 &clk_sel_val); 1147 status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, 1148 &Data); 1149 if (status < 0) { 1150 dev_dbg(&port->dev, "reading spreg failed in set_serial_baud\n"); 1151 return -1; 1152 } 1153 Data = (Data & 0x8f) | clk_sel_val; 1154 status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, 1155 Data); 1156 if (status < 0) { 1157 dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n"); 1158 return -1; 1159 } 1160 /* Calculate the Divisor */ 1161 1162 if (status) { 1163 dev_err(&port->dev, "%s - bad baud rate\n", __func__); 1164 return status; 1165 } 1166 /* Enable access to divisor latch */ 1167 Data = mos7840_port->shadowLCR | SERIAL_LCR_DLAB; 1168 mos7840_port->shadowLCR = Data; 1169 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); 1170 1171 /* Write the divisor */ 1172 Data = (unsigned char)(divisor & 0xff); 1173 dev_dbg(&port->dev, "set_serial_baud Value to write DLL is %x\n", Data); 1174 mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data); 1175 1176 Data = (unsigned char)((divisor & 0xff00) >> 8); 1177 dev_dbg(&port->dev, "set_serial_baud Value to write DLM is %x\n", Data); 1178 mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data); 1179 1180 /* Disable access to divisor latch */ 1181 Data = mos7840_port->shadowLCR & ~SERIAL_LCR_DLAB; 1182 mos7840_port->shadowLCR = Data; 1183 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); 1184 1185 } 1186 return status; 1187 } 1188 1189 /***************************************************************************** 1190 * mos7840_change_port_settings 1191 * This routine is called to set the UART on the device to match 1192 * the specified new settings. 1193 *****************************************************************************/ 1194 1195 static void mos7840_change_port_settings(struct tty_struct *tty, 1196 struct moschip_port *mos7840_port, struct ktermios *old_termios) 1197 { 1198 struct usb_serial_port *port = mos7840_port->port; 1199 int baud; 1200 unsigned cflag; 1201 __u8 lData; 1202 __u8 lParity; 1203 __u8 lStop; 1204 int status; 1205 __u16 Data; 1206 1207 lData = LCR_BITS_8; 1208 lStop = LCR_STOP_1; 1209 lParity = LCR_PAR_NONE; 1210 1211 cflag = tty->termios.c_cflag; 1212 1213 /* Change the number of bits */ 1214 switch (cflag & CSIZE) { 1215 case CS5: 1216 lData = LCR_BITS_5; 1217 break; 1218 1219 case CS6: 1220 lData = LCR_BITS_6; 1221 break; 1222 1223 case CS7: 1224 lData = LCR_BITS_7; 1225 break; 1226 1227 default: 1228 case CS8: 1229 lData = LCR_BITS_8; 1230 break; 1231 } 1232 1233 /* Change the Parity bit */ 1234 if (cflag & PARENB) { 1235 if (cflag & PARODD) { 1236 lParity = LCR_PAR_ODD; 1237 dev_dbg(&port->dev, "%s - parity = odd\n", __func__); 1238 } else { 1239 lParity = LCR_PAR_EVEN; 1240 dev_dbg(&port->dev, "%s - parity = even\n", __func__); 1241 } 1242 1243 } else { 1244 dev_dbg(&port->dev, "%s - parity = none\n", __func__); 1245 } 1246 1247 if (cflag & CMSPAR) 1248 lParity = lParity | 0x20; 1249 1250 /* Change the Stop bit */ 1251 if (cflag & CSTOPB) { 1252 lStop = LCR_STOP_2; 1253 dev_dbg(&port->dev, "%s - stop bits = 2\n", __func__); 1254 } else { 1255 lStop = LCR_STOP_1; 1256 dev_dbg(&port->dev, "%s - stop bits = 1\n", __func__); 1257 } 1258 1259 /* Update the LCR with the correct value */ 1260 mos7840_port->shadowLCR &= 1261 ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK); 1262 mos7840_port->shadowLCR |= (lData | lParity | lStop); 1263 1264 dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is %x\n", __func__, 1265 mos7840_port->shadowLCR); 1266 /* Disable Interrupts */ 1267 Data = 0x00; 1268 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); 1269 1270 Data = 0x00; 1271 mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); 1272 1273 Data = 0xcf; 1274 mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data); 1275 1276 /* Send the updated LCR value to the mos7840 */ 1277 Data = mos7840_port->shadowLCR; 1278 1279 mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data); 1280 1281 Data = 0x00b; 1282 mos7840_port->shadowMCR = Data; 1283 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); 1284 Data = 0x00b; 1285 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); 1286 1287 /* set up the MCR register and send it to the mos7840 */ 1288 1289 mos7840_port->shadowMCR = MCR_MASTER_IE; 1290 if (cflag & CBAUD) 1291 mos7840_port->shadowMCR |= (MCR_DTR | MCR_RTS); 1292 1293 if (cflag & CRTSCTS) 1294 mos7840_port->shadowMCR |= (MCR_XON_ANY); 1295 else 1296 mos7840_port->shadowMCR &= ~(MCR_XON_ANY); 1297 1298 Data = mos7840_port->shadowMCR; 1299 mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, Data); 1300 1301 /* Determine divisor based on baud rate */ 1302 baud = tty_get_baud_rate(tty); 1303 1304 if (!baud) { 1305 /* pick a default, any default... */ 1306 dev_dbg(&port->dev, "%s", "Picked default baud...\n"); 1307 baud = 9600; 1308 } 1309 1310 dev_dbg(&port->dev, "%s - baud rate = %d\n", __func__, baud); 1311 status = mos7840_send_cmd_write_baud_rate(mos7840_port, baud); 1312 1313 /* Enable Interrupts */ 1314 Data = 0x0c; 1315 mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data); 1316 1317 if (!mos7840_port->read_urb_busy) { 1318 mos7840_port->read_urb_busy = true; 1319 status = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL); 1320 if (status) { 1321 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n", 1322 status); 1323 mos7840_port->read_urb_busy = false; 1324 } 1325 } 1326 dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is End %x\n", __func__, 1327 mos7840_port->shadowLCR); 1328 } 1329 1330 /***************************************************************************** 1331 * mos7840_set_termios 1332 * this function is called by the tty driver when it wants to change 1333 * the termios structure 1334 *****************************************************************************/ 1335 1336 static void mos7840_set_termios(struct tty_struct *tty, 1337 struct usb_serial_port *port, 1338 struct ktermios *old_termios) 1339 { 1340 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 1341 int status; 1342 1343 /* change the port settings to the new ones specified */ 1344 1345 mos7840_change_port_settings(tty, mos7840_port, old_termios); 1346 1347 if (!mos7840_port->read_urb_busy) { 1348 mos7840_port->read_urb_busy = true; 1349 status = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL); 1350 if (status) { 1351 dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n", 1352 status); 1353 mos7840_port->read_urb_busy = false; 1354 } 1355 } 1356 } 1357 1358 /***************************************************************************** 1359 * mos7840_get_lsr_info - get line status register info 1360 * 1361 * Purpose: Let user call ioctl() to get info when the UART physically 1362 * is emptied. On bus types like RS485, the transmitter must 1363 * release the bus after transmitting. This must be done when 1364 * the transmit shift register is empty, not be done when the 1365 * transmit holding register is empty. This functionality 1366 * allows an RS485 driver to be written in user space. 1367 *****************************************************************************/ 1368 1369 static int mos7840_get_lsr_info(struct tty_struct *tty, 1370 unsigned int __user *value) 1371 { 1372 int count; 1373 unsigned int result = 0; 1374 1375 count = mos7840_chars_in_buffer(tty); 1376 if (count == 0) 1377 result = TIOCSER_TEMT; 1378 1379 if (copy_to_user(value, &result, sizeof(int))) 1380 return -EFAULT; 1381 return 0; 1382 } 1383 1384 /***************************************************************************** 1385 * mos7840_get_serial_info 1386 * function to get information about serial port 1387 *****************************************************************************/ 1388 1389 static int mos7840_get_serial_info(struct tty_struct *tty, 1390 struct serial_struct *ss) 1391 { 1392 struct usb_serial_port *port = tty->driver_data; 1393 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 1394 1395 ss->type = PORT_16550A; 1396 ss->line = mos7840_port->port->minor; 1397 ss->port = mos7840_port->port->port_number; 1398 ss->irq = 0; 1399 ss->xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE; 1400 ss->baud_base = 9600; 1401 ss->close_delay = 5 * HZ; 1402 ss->closing_wait = 30 * HZ; 1403 return 0; 1404 } 1405 1406 /***************************************************************************** 1407 * SerialIoctl 1408 * this function handles any ioctl calls to the driver 1409 *****************************************************************************/ 1410 1411 static int mos7840_ioctl(struct tty_struct *tty, 1412 unsigned int cmd, unsigned long arg) 1413 { 1414 struct usb_serial_port *port = tty->driver_data; 1415 void __user *argp = (void __user *)arg; 1416 1417 switch (cmd) { 1418 /* return number of bytes available */ 1419 1420 case TIOCSERGETLSR: 1421 dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__); 1422 return mos7840_get_lsr_info(tty, argp); 1423 1424 default: 1425 break; 1426 } 1427 return -ENOIOCTLCMD; 1428 } 1429 1430 /* 1431 * Check if GPO (pin 42) is connected to GPI (pin 33) as recommended by ASIX 1432 * for MCS7810 by bit-banging a 16-bit word. 1433 * 1434 * Note that GPO is really RTS of the third port so this will toggle RTS of 1435 * port two or three on two- and four-port devices. 1436 */ 1437 static int mos7810_check(struct usb_serial *serial) 1438 { 1439 int i, pass_count = 0; 1440 u8 *buf; 1441 __u16 data = 0, mcr_data = 0; 1442 __u16 test_pattern = 0x55AA; 1443 int res; 1444 1445 buf = kmalloc(VENDOR_READ_LENGTH, GFP_KERNEL); 1446 if (!buf) 1447 return 0; /* failed to identify 7810 */ 1448 1449 /* Store MCR setting */ 1450 res = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), 1451 MCS_RDREQ, MCS_RD_RTYPE, 0x0300, MODEM_CONTROL_REGISTER, 1452 buf, VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); 1453 if (res == VENDOR_READ_LENGTH) 1454 mcr_data = *buf; 1455 1456 for (i = 0; i < 16; i++) { 1457 /* Send the 1-bit test pattern out to MCS7810 test pin */ 1458 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), 1459 MCS_WRREQ, MCS_WR_RTYPE, 1460 (0x0300 | (((test_pattern >> i) & 0x0001) << 1)), 1461 MODEM_CONTROL_REGISTER, NULL, 0, MOS_WDR_TIMEOUT); 1462 1463 /* Read the test pattern back */ 1464 res = usb_control_msg(serial->dev, 1465 usb_rcvctrlpipe(serial->dev, 0), MCS_RDREQ, 1466 MCS_RD_RTYPE, 0, GPIO_REGISTER, buf, 1467 VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); 1468 if (res == VENDOR_READ_LENGTH) 1469 data = *buf; 1470 1471 /* If this is a MCS7810 device, both test patterns must match */ 1472 if (((test_pattern >> i) ^ (~data >> 1)) & 0x0001) 1473 break; 1474 1475 pass_count++; 1476 } 1477 1478 /* Restore MCR setting */ 1479 usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0), MCS_WRREQ, 1480 MCS_WR_RTYPE, 0x0300 | mcr_data, MODEM_CONTROL_REGISTER, NULL, 1481 0, MOS_WDR_TIMEOUT); 1482 1483 kfree(buf); 1484 1485 if (pass_count == 16) 1486 return 1; 1487 1488 return 0; 1489 } 1490 1491 static int mos7840_probe(struct usb_serial *serial, 1492 const struct usb_device_id *id) 1493 { 1494 unsigned long device_flags = id->driver_info; 1495 u8 *buf; 1496 1497 /* Skip device-type detection if we already have device flags. */ 1498 if (device_flags) 1499 goto out; 1500 1501 buf = kzalloc(VENDOR_READ_LENGTH, GFP_KERNEL); 1502 if (!buf) 1503 return -ENOMEM; 1504 1505 usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0), 1506 MCS_RDREQ, MCS_RD_RTYPE, 0, GPIO_REGISTER, buf, 1507 VENDOR_READ_LENGTH, MOS_WDR_TIMEOUT); 1508 1509 /* For a MCS7840 device GPIO0 must be set to 1 */ 1510 if (buf[0] & 0x01) 1511 device_flags = MCS_PORTS(4); 1512 else if (mos7810_check(serial)) 1513 device_flags = MCS_PORTS(1) | MCS_LED; 1514 else 1515 device_flags = MCS_PORTS(2); 1516 1517 kfree(buf); 1518 out: 1519 usb_set_serial_data(serial, (void *)device_flags); 1520 1521 return 0; 1522 } 1523 1524 static int mos7840_calc_num_ports(struct usb_serial *serial, 1525 struct usb_serial_endpoints *epds) 1526 { 1527 unsigned long device_flags = (unsigned long)usb_get_serial_data(serial); 1528 int num_ports = MCS_PORTS(device_flags); 1529 1530 if (num_ports == 0 || num_ports > 4) 1531 return -ENODEV; 1532 1533 if (epds->num_bulk_in < num_ports || epds->num_bulk_out < num_ports) { 1534 dev_err(&serial->interface->dev, "missing endpoints\n"); 1535 return -ENODEV; 1536 } 1537 1538 return num_ports; 1539 } 1540 1541 static int mos7840_attach(struct usb_serial *serial) 1542 { 1543 struct device *dev = &serial->interface->dev; 1544 int status; 1545 u16 val; 1546 1547 /* Zero Length flag enable */ 1548 val = 0x0f; 1549 status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, val); 1550 if (status < 0) 1551 dev_dbg(dev, "Writing ZLP_REG5 failed status-0x%x\n", status); 1552 else 1553 dev_dbg(dev, "ZLP_REG5 Writing success status%d\n", status); 1554 1555 return status; 1556 } 1557 1558 static int mos7840_port_probe(struct usb_serial_port *port) 1559 { 1560 struct usb_serial *serial = port->serial; 1561 unsigned long device_flags = (unsigned long)usb_get_serial_data(serial); 1562 struct moschip_port *mos7840_port; 1563 int status; 1564 int pnum; 1565 __u16 Data; 1566 1567 /* we set up the pointers to the endpoints in the mos7840_open * 1568 * function, as the structures aren't created yet. */ 1569 1570 pnum = port->port_number; 1571 1572 dev_dbg(&port->dev, "mos7840_startup: configuring port %d\n", pnum); 1573 mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL); 1574 if (!mos7840_port) 1575 return -ENOMEM; 1576 1577 /* Initialize all port interrupt end point to port 0 int 1578 * endpoint. Our device has only one interrupt end point 1579 * common to all port */ 1580 1581 mos7840_port->port = port; 1582 spin_lock_init(&mos7840_port->pool_lock); 1583 1584 /* minor is not initialised until later by 1585 * usb-serial.c:get_free_serial() and cannot therefore be used 1586 * to index device instances */ 1587 mos7840_port->port_num = pnum + 1; 1588 dev_dbg(&port->dev, "port->minor = %d\n", port->minor); 1589 dev_dbg(&port->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num); 1590 1591 if (mos7840_port->port_num == 1) { 1592 mos7840_port->SpRegOffset = 0x0; 1593 mos7840_port->ControlRegOffset = 0x1; 1594 mos7840_port->DcrRegOffset = 0x4; 1595 } else { 1596 u8 phy_num = mos7840_port->port_num; 1597 1598 /* Port 2 in the 2-port case uses registers of port 3 */ 1599 if (serial->num_ports == 2) 1600 phy_num = 3; 1601 1602 mos7840_port->SpRegOffset = 0x8 + 2 * (phy_num - 2); 1603 mos7840_port->ControlRegOffset = 0x9 + 2 * (phy_num - 2); 1604 mos7840_port->DcrRegOffset = 0x16 + 3 * (phy_num - 2); 1605 } 1606 mos7840_dump_serial_port(port, mos7840_port); 1607 usb_set_serial_port_data(port, mos7840_port); 1608 1609 /* enable rx_disable bit in control register */ 1610 status = mos7840_get_reg_sync(port, 1611 mos7840_port->ControlRegOffset, &Data); 1612 if (status < 0) { 1613 dev_dbg(&port->dev, "Reading ControlReg failed status-0x%x\n", status); 1614 goto error; 1615 } else 1616 dev_dbg(&port->dev, "ControlReg Reading success val is %x, status%d\n", Data, status); 1617 Data |= 0x08; /* setting driver done bit */ 1618 Data |= 0x04; /* sp1_bit to have cts change reflect in 1619 modem status reg */ 1620 1621 /* Data |= 0x20; //rx_disable bit */ 1622 status = mos7840_set_reg_sync(port, 1623 mos7840_port->ControlRegOffset, Data); 1624 if (status < 0) { 1625 dev_dbg(&port->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status); 1626 goto error; 1627 } else 1628 dev_dbg(&port->dev, "ControlReg Writing success(rx_disable) status%d\n", status); 1629 1630 /* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2 1631 and 0x24 in DCR3 */ 1632 Data = 0x01; 1633 status = mos7840_set_reg_sync(port, 1634 (__u16) (mos7840_port->DcrRegOffset + 0), Data); 1635 if (status < 0) { 1636 dev_dbg(&port->dev, "Writing DCR0 failed status-0x%x\n", status); 1637 goto error; 1638 } else 1639 dev_dbg(&port->dev, "DCR0 Writing success status%d\n", status); 1640 1641 Data = 0x05; 1642 status = mos7840_set_reg_sync(port, 1643 (__u16) (mos7840_port->DcrRegOffset + 1), Data); 1644 if (status < 0) { 1645 dev_dbg(&port->dev, "Writing DCR1 failed status-0x%x\n", status); 1646 goto error; 1647 } else 1648 dev_dbg(&port->dev, "DCR1 Writing success status%d\n", status); 1649 1650 Data = 0x24; 1651 status = mos7840_set_reg_sync(port, 1652 (__u16) (mos7840_port->DcrRegOffset + 2), Data); 1653 if (status < 0) { 1654 dev_dbg(&port->dev, "Writing DCR2 failed status-0x%x\n", status); 1655 goto error; 1656 } else 1657 dev_dbg(&port->dev, "DCR2 Writing success status%d\n", status); 1658 1659 /* write values in clkstart0x0 and clkmulti 0x20 */ 1660 Data = 0x0; 1661 status = mos7840_set_reg_sync(port, CLK_START_VALUE_REGISTER, Data); 1662 if (status < 0) { 1663 dev_dbg(&port->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status); 1664 goto error; 1665 } else 1666 dev_dbg(&port->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status); 1667 1668 Data = 0x20; 1669 status = mos7840_set_reg_sync(port, CLK_MULTI_REGISTER, Data); 1670 if (status < 0) { 1671 dev_dbg(&port->dev, "Writing CLK_MULTI_REGISTER failed status-0x%x\n", status); 1672 goto error; 1673 } else 1674 dev_dbg(&port->dev, "CLK_MULTI_REGISTER Writing success status%d\n", status); 1675 1676 /* write value 0x0 to scratchpad register */ 1677 Data = 0x00; 1678 status = mos7840_set_uart_reg(port, SCRATCH_PAD_REGISTER, Data); 1679 if (status < 0) { 1680 dev_dbg(&port->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status); 1681 goto error; 1682 } else 1683 dev_dbg(&port->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status); 1684 1685 /* Zero Length flag register */ 1686 if ((mos7840_port->port_num != 1) && (serial->num_ports == 2)) { 1687 Data = 0xff; 1688 status = mos7840_set_reg_sync(port, 1689 (__u16) (ZLP_REG1 + 1690 ((__u16)mos7840_port->port_num)), Data); 1691 dev_dbg(&port->dev, "ZLIP offset %x\n", 1692 (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num))); 1693 if (status < 0) { 1694 dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 2, status); 1695 goto error; 1696 } else 1697 dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 2, status); 1698 } else { 1699 Data = 0xff; 1700 status = mos7840_set_reg_sync(port, 1701 (__u16) (ZLP_REG1 + 1702 ((__u16)mos7840_port->port_num) - 0x1), Data); 1703 dev_dbg(&port->dev, "ZLIP offset %x\n", 1704 (__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1)); 1705 if (status < 0) { 1706 dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 1, status); 1707 goto error; 1708 } else 1709 dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 1, status); 1710 1711 } 1712 1713 mos7840_port->has_led = device_flags & MCS_LED; 1714 1715 /* Initialize LED timers */ 1716 if (mos7840_port->has_led) { 1717 mos7840_port->led_urb = usb_alloc_urb(0, GFP_KERNEL); 1718 mos7840_port->led_dr = kmalloc(sizeof(*mos7840_port->led_dr), 1719 GFP_KERNEL); 1720 if (!mos7840_port->led_urb || !mos7840_port->led_dr) { 1721 status = -ENOMEM; 1722 goto error; 1723 } 1724 1725 timer_setup(&mos7840_port->led_timer1, mos7840_led_off, 0); 1726 mos7840_port->led_timer1.expires = 1727 jiffies + msecs_to_jiffies(LED_ON_MS); 1728 timer_setup(&mos7840_port->led_timer2, mos7840_led_flag_off, 1729 0); 1730 mos7840_port->led_timer2.expires = 1731 jiffies + msecs_to_jiffies(LED_OFF_MS); 1732 1733 /* Turn off LED */ 1734 mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300); 1735 } 1736 1737 return 0; 1738 error: 1739 kfree(mos7840_port->led_dr); 1740 usb_free_urb(mos7840_port->led_urb); 1741 kfree(mos7840_port); 1742 1743 return status; 1744 } 1745 1746 static int mos7840_port_remove(struct usb_serial_port *port) 1747 { 1748 struct moschip_port *mos7840_port = usb_get_serial_port_data(port); 1749 1750 if (mos7840_port->has_led) { 1751 /* Turn off LED */ 1752 mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300); 1753 1754 del_timer_sync(&mos7840_port->led_timer1); 1755 del_timer_sync(&mos7840_port->led_timer2); 1756 1757 usb_kill_urb(mos7840_port->led_urb); 1758 usb_free_urb(mos7840_port->led_urb); 1759 kfree(mos7840_port->led_dr); 1760 } 1761 1762 kfree(mos7840_port); 1763 1764 return 0; 1765 } 1766 1767 static struct usb_serial_driver moschip7840_4port_device = { 1768 .driver = { 1769 .owner = THIS_MODULE, 1770 .name = "mos7840", 1771 }, 1772 .description = DRIVER_DESC, 1773 .id_table = id_table, 1774 .num_interrupt_in = 1, 1775 .open = mos7840_open, 1776 .close = mos7840_close, 1777 .write = mos7840_write, 1778 .write_room = mos7840_write_room, 1779 .chars_in_buffer = mos7840_chars_in_buffer, 1780 .throttle = mos7840_throttle, 1781 .unthrottle = mos7840_unthrottle, 1782 .calc_num_ports = mos7840_calc_num_ports, 1783 .probe = mos7840_probe, 1784 .attach = mos7840_attach, 1785 .ioctl = mos7840_ioctl, 1786 .get_serial = mos7840_get_serial_info, 1787 .set_termios = mos7840_set_termios, 1788 .break_ctl = mos7840_break, 1789 .tiocmget = mos7840_tiocmget, 1790 .tiocmset = mos7840_tiocmset, 1791 .get_icount = usb_serial_generic_get_icount, 1792 .port_probe = mos7840_port_probe, 1793 .port_remove = mos7840_port_remove, 1794 .read_bulk_callback = mos7840_bulk_in_callback, 1795 }; 1796 1797 static struct usb_serial_driver * const serial_drivers[] = { 1798 &moschip7840_4port_device, NULL 1799 }; 1800 1801 module_usb_serial_driver(serial_drivers, id_table); 1802 1803 MODULE_DESCRIPTION(DRIVER_DESC); 1804 MODULE_LICENSE("GPL"); 1805