1 /* 2 * IPWireless 3G UMTS TDD Modem driver (USB connected) 3 * 4 * Copyright (C) 2004 Roelf Diedericks <roelfd@inet.co.za> 5 * Copyright (C) 2004 Greg Kroah-Hartman <greg@kroah.com> 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License as published by 9 * the Free Software Foundation; either version 2 of the License, or 10 * (at your option) any later version. 11 * 12 * All information about the device was acquired using SnoopyPro 13 * on MSFT's O/S, and examing the MSFT drivers' debug output 14 * (insanely left _on_ in the enduser version) 15 * 16 * It was written out of frustration with the IPWireless USB modem 17 * supplied by Axity3G/Sentech South Africa not supporting 18 * Linux whatsoever. 19 * 20 * Nobody provided any proprietary information that was not already 21 * available for this device. 22 * 23 * The modem adheres to the "3GPP TS 27.007 AT command set for 3G 24 * User Equipment (UE)" standard, available from 25 * http://www.3gpp.org/ftp/Specs/html-info/27007.htm 26 * 27 * The code was only tested the IPWireless handheld modem distributed 28 * in South Africa by Sentech. 29 * 30 * It may work for Woosh Inc in .nz too, as it appears they use the 31 * same kit. 32 * 33 * There is still some work to be done in terms of handling 34 * DCD, DTR, RTS, CTS which are currently faked. 35 * It's good enough for PPP at this point. It's based off all kinds of 36 * code found in usb/serial and usb/class 37 * 38 */ 39 40 #include <linux/kernel.h> 41 #include <linux/errno.h> 42 #include <linux/init.h> 43 #include <linux/slab.h> 44 #include <linux/tty.h> 45 #include <linux/tty_flip.h> 46 #include <linux/module.h> 47 #include <linux/spinlock.h> 48 #include <linux/usb.h> 49 #include <linux/usb/serial.h> 50 #include <asm/uaccess.h> 51 52 /* 53 * Version Information 54 */ 55 #define DRIVER_VERSION "v0.3" 56 #define DRIVER_AUTHOR "Roelf Diedericks" 57 #define DRIVER_DESC "IPWireless tty driver" 58 59 #define IPW_TTY_MAJOR 240 /* real device node major id, experimental range */ 60 #define IPW_TTY_MINORS 256 /* we support 256 devices, dunno why, it'd be insane :) */ 61 62 #define USB_IPW_MAGIC 0x6d02 /* magic number for ipw struct */ 63 64 65 /* Message sizes */ 66 #define EVENT_BUFFER_SIZE 0xFF 67 #define CHAR2INT16(c1,c0) (((u32)((c1) & 0xff) << 8) + (u32)((c0) & 0xff)) 68 #define NUM_BULK_URBS 24 69 #define NUM_CONTROL_URBS 16 70 71 /* vendor/product pairs that are known work with this driver*/ 72 #define IPW_VID 0x0bc3 73 #define IPW_PID 0x0001 74 75 76 /* Vendor commands: */ 77 78 /* baud rates */ 79 enum { 80 ipw_sio_b256000 = 0x000e, 81 ipw_sio_b128000 = 0x001d, 82 ipw_sio_b115200 = 0x0020, 83 ipw_sio_b57600 = 0x0040, 84 ipw_sio_b56000 = 0x0042, 85 ipw_sio_b38400 = 0x0060, 86 ipw_sio_b19200 = 0x00c0, 87 ipw_sio_b14400 = 0x0100, 88 ipw_sio_b9600 = 0x0180, 89 ipw_sio_b4800 = 0x0300, 90 ipw_sio_b2400 = 0x0600, 91 ipw_sio_b1200 = 0x0c00, 92 ipw_sio_b600 = 0x1800 93 }; 94 95 /* data bits */ 96 #define ipw_dtb_7 0x700 97 #define ipw_dtb_8 0x810 // ok so the define is misleading, I know, but forces 8,n,1 98 // I mean, is there a point to any other setting these days? :) 99 100 /* usb control request types : */ 101 #define IPW_SIO_RXCTL 0x00 // control bulk rx channel transmissions, value=1/0 (on/off) 102 #define IPW_SIO_SET_BAUD 0x01 // set baud, value=requested ipw_sio_bxxxx 103 #define IPW_SIO_SET_LINE 0x03 // set databits, parity. value=ipw_dtb_x 104 #define IPW_SIO_SET_PIN 0x03 // set/clear dtr/rts value=ipw_pin_xxx 105 #define IPW_SIO_POLL 0x08 // get serial port status byte, call with value=0 106 #define IPW_SIO_INIT 0x11 // initializes ? value=0 (appears as first thing todo on open) 107 #define IPW_SIO_PURGE 0x12 // purge all transmissions?, call with value=numchar_to_purge 108 #define IPW_SIO_HANDFLOW 0x13 // set xon/xoff limits value=0, and a buffer of 0x10 bytes 109 #define IPW_SIO_SETCHARS 0x13 // set the flowcontrol special chars, value=0, buf=6 bytes, 110 // last 2 bytes contain flowcontrol chars e.g. 00 00 00 00 11 13 111 112 /* values used for request IPW_SIO_SET_PIN */ 113 #define IPW_PIN_SETDTR 0x101 114 #define IPW_PIN_SETRTS 0x202 115 #define IPW_PIN_CLRDTR 0x100 116 #define IPW_PIN_CLRRTS 0x200 // unconfirmed 117 118 /* values used for request IPW_SIO_RXCTL */ 119 #define IPW_RXBULK_ON 1 120 #define IPW_RXBULK_OFF 0 121 122 /* various 16 byte hardcoded transferbuffers used by flow control */ 123 #define IPW_BYTES_FLOWINIT { 0x01, 0, 0, 0, 0x40, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 } 124 125 /* Interpretation of modem status lines */ 126 /* These need sorting out by individually connecting pins and checking 127 * results. FIXME! 128 * When data is being sent we see 0x30 in the lower byte; this must 129 * contain DSR and CTS ... 130 */ 131 #define IPW_DSR ((1<<4) | (1<<5)) 132 #define IPW_CTS ((1<<5) | (1<<4)) 133 134 #define IPW_WANTS_TO_SEND 0x30 135 //#define IPW_DTR /* Data Terminal Ready */ 136 //#define IPW_CTS /* Clear To Send */ 137 //#define IPW_CD /* Carrier Detect */ 138 //#define IPW_DSR /* Data Set Ready */ 139 //#define IPW_RxD /* Receive pin */ 140 141 //#define IPW_LE 142 //#define IPW_RTS 143 //#define IPW_ST 144 //#define IPW_SR 145 //#define IPW_RI /* Ring Indicator */ 146 147 static struct usb_device_id usb_ipw_ids[] = { 148 { USB_DEVICE(IPW_VID, IPW_PID) }, 149 { }, 150 }; 151 152 MODULE_DEVICE_TABLE(usb, usb_ipw_ids); 153 154 static struct usb_driver usb_ipw_driver = { 155 .name = "ipwtty", 156 .probe = usb_serial_probe, 157 .disconnect = usb_serial_disconnect, 158 .id_table = usb_ipw_ids, 159 .no_dynamic_id = 1, 160 }; 161 162 static int debug; 163 164 static void ipw_read_bulk_callback(struct urb *urb) 165 { 166 struct usb_serial_port *port = urb->context; 167 unsigned char *data = urb->transfer_buffer; 168 struct tty_struct *tty; 169 int result; 170 int status = urb->status; 171 172 dbg("%s - port %d", __FUNCTION__, port->number); 173 174 if (status) { 175 dbg("%s - nonzero read bulk status received: %d", 176 __FUNCTION__, status); 177 return; 178 } 179 180 usb_serial_debug_data(debug, &port->dev, __FUNCTION__, urb->actual_length, data); 181 182 tty = port->tty; 183 if (tty && urb->actual_length) { 184 tty_buffer_request_room(tty, urb->actual_length); 185 tty_insert_flip_string(tty, data, urb->actual_length); 186 tty_flip_buffer_push(tty); 187 } 188 189 /* Continue trying to always read */ 190 usb_fill_bulk_urb (port->read_urb, port->serial->dev, 191 usb_rcvbulkpipe(port->serial->dev, 192 port->bulk_in_endpointAddress), 193 port->read_urb->transfer_buffer, 194 port->read_urb->transfer_buffer_length, 195 ipw_read_bulk_callback, port); 196 result = usb_submit_urb(port->read_urb, GFP_ATOMIC); 197 if (result) 198 dev_err(&port->dev, "%s - failed resubmitting read urb, error %d\n", __FUNCTION__, result); 199 return; 200 } 201 202 static int ipw_open(struct usb_serial_port *port, struct file *filp) 203 { 204 struct usb_device *dev = port->serial->dev; 205 u8 buf_flow_static[16] = IPW_BYTES_FLOWINIT; 206 u8 *buf_flow_init; 207 int result; 208 209 dbg("%s", __FUNCTION__); 210 211 buf_flow_init = kmemdup(buf_flow_static, 16, GFP_KERNEL); 212 if (!buf_flow_init) 213 return -ENOMEM; 214 215 if (port->tty) 216 port->tty->low_latency = 1; 217 218 /* --1: Tell the modem to initialize (we think) From sniffs this is always the 219 * first thing that gets sent to the modem during opening of the device */ 220 dbg("%s: Sending SIO_INIT (we guess)",__FUNCTION__); 221 result = usb_control_msg(dev, usb_sndctrlpipe(dev,0), 222 IPW_SIO_INIT, 223 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 224 0, 225 0, /* index */ 226 NULL, 227 0, 228 100000); 229 if (result < 0) 230 dev_err(&port->dev, "Init of modem failed (error = %d)", result); 231 232 /* reset the bulk pipes */ 233 usb_clear_halt(dev, usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress)); 234 usb_clear_halt(dev, usb_sndbulkpipe(dev, port->bulk_out_endpointAddress)); 235 236 /*--2: Start reading from the device */ 237 dbg("%s: setting up bulk read callback",__FUNCTION__); 238 usb_fill_bulk_urb(port->read_urb, dev, 239 usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress), 240 port->bulk_in_buffer, 241 port->bulk_in_size, 242 ipw_read_bulk_callback, port); 243 result = usb_submit_urb(port->read_urb, GFP_KERNEL); 244 if (result < 0) 245 dbg("%s - usb_submit_urb(read bulk) failed with status %d", __FUNCTION__, result); 246 247 /*--3: Tell the modem to open the floodgates on the rx bulk channel */ 248 dbg("%s:asking modem for RxRead (RXBULK_ON)",__FUNCTION__); 249 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 250 IPW_SIO_RXCTL, 251 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 252 IPW_RXBULK_ON, 253 0, /* index */ 254 NULL, 255 0, 256 100000); 257 if (result < 0) 258 dev_err(&port->dev, "Enabling bulk RxRead failed (error = %d)", result); 259 260 /*--4: setup the initial flowcontrol */ 261 dbg("%s:setting init flowcontrol (%s)",__FUNCTION__,buf_flow_init); 262 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 263 IPW_SIO_HANDFLOW, 264 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 265 0, 266 0, 267 buf_flow_init, 268 0x10, 269 200000); 270 if (result < 0) 271 dev_err(&port->dev, "initial flowcontrol failed (error = %d)", result); 272 273 274 /*--5: raise the dtr */ 275 dbg("%s:raising dtr",__FUNCTION__); 276 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 277 IPW_SIO_SET_PIN, 278 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 279 IPW_PIN_SETDTR, 280 0, 281 NULL, 282 0, 283 200000); 284 if (result < 0) 285 dev_err(&port->dev, "setting dtr failed (error = %d)", result); 286 287 /*--6: raise the rts */ 288 dbg("%s:raising rts",__FUNCTION__); 289 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 290 IPW_SIO_SET_PIN, 291 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 292 IPW_PIN_SETRTS, 293 0, 294 NULL, 295 0, 296 200000); 297 if (result < 0) 298 dev_err(&port->dev, "setting dtr failed (error = %d)", result); 299 300 kfree(buf_flow_init); 301 return 0; 302 } 303 304 static void ipw_close(struct usb_serial_port *port, struct file * filp) 305 { 306 struct usb_device *dev = port->serial->dev; 307 int result; 308 309 if (tty_hung_up_p(filp)) { 310 dbg("%s: tty_hung_up_p ...", __FUNCTION__); 311 return; 312 } 313 314 /*--1: drop the dtr */ 315 dbg("%s:dropping dtr",__FUNCTION__); 316 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 317 IPW_SIO_SET_PIN, 318 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 319 IPW_PIN_CLRDTR, 320 0, 321 NULL, 322 0, 323 200000); 324 if (result < 0) 325 dev_err(&port->dev, "dropping dtr failed (error = %d)", result); 326 327 /*--2: drop the rts */ 328 dbg("%s:dropping rts",__FUNCTION__); 329 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 330 IPW_SIO_SET_PIN, USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 331 IPW_PIN_CLRRTS, 332 0, 333 NULL, 334 0, 335 200000); 336 if (result < 0) 337 dev_err(&port->dev, "dropping rts failed (error = %d)", result); 338 339 340 /*--3: purge */ 341 dbg("%s:sending purge",__FUNCTION__); 342 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 343 IPW_SIO_PURGE, USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 344 0x03, 345 0, 346 NULL, 347 0, 348 200000); 349 if (result < 0) 350 dev_err(&port->dev, "purge failed (error = %d)", result); 351 352 353 /* send RXBULK_off (tell modem to stop transmitting bulk data on rx chan) */ 354 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 355 IPW_SIO_RXCTL, 356 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 357 IPW_RXBULK_OFF, 358 0, /* index */ 359 NULL, 360 0, 361 100000); 362 363 if (result < 0) 364 dev_err(&port->dev, "Disabling bulk RxRead failed (error = %d)", result); 365 366 /* shutdown any in-flight urbs that we know about */ 367 usb_kill_urb(port->read_urb); 368 usb_kill_urb(port->write_urb); 369 } 370 371 static void ipw_write_bulk_callback(struct urb *urb) 372 { 373 struct usb_serial_port *port = urb->context; 374 int status = urb->status; 375 376 dbg("%s", __FUNCTION__); 377 378 port->write_urb_busy = 0; 379 380 if (status) 381 dbg("%s - nonzero write bulk status received: %d", 382 __FUNCTION__, status); 383 384 usb_serial_port_softint(port); 385 } 386 387 static int ipw_write(struct usb_serial_port *port, const unsigned char *buf, int count) 388 { 389 struct usb_device *dev = port->serial->dev; 390 int ret; 391 392 dbg("%s: TOP: count=%d, in_interrupt=%ld", __FUNCTION__, 393 count, in_interrupt() ); 394 395 if (count == 0) { 396 dbg("%s - write request of 0 bytes", __FUNCTION__); 397 return 0; 398 } 399 400 spin_lock_bh(&port->lock); 401 if (port->write_urb_busy) { 402 spin_unlock_bh(&port->lock); 403 dbg("%s - already writing", __FUNCTION__); 404 return 0; 405 } 406 port->write_urb_busy = 1; 407 spin_unlock_bh(&port->lock); 408 409 count = min(count, port->bulk_out_size); 410 memcpy(port->bulk_out_buffer, buf, count); 411 412 dbg("%s count now:%d", __FUNCTION__, count); 413 414 usb_fill_bulk_urb(port->write_urb, dev, 415 usb_sndbulkpipe(dev, port->bulk_out_endpointAddress), 416 port->write_urb->transfer_buffer, 417 count, 418 ipw_write_bulk_callback, 419 port); 420 421 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 422 if (ret != 0) { 423 port->write_urb_busy = 0; 424 dbg("%s - usb_submit_urb(write bulk) failed with error = %d", __FUNCTION__, ret); 425 return ret; 426 } 427 428 dbg("%s returning %d", __FUNCTION__, count); 429 return count; 430 } 431 432 static int ipw_probe(struct usb_serial_port *port) 433 { 434 return 0; 435 } 436 437 static int ipw_disconnect(struct usb_serial_port *port) 438 { 439 usb_set_serial_port_data(port, NULL); 440 return 0; 441 } 442 443 static struct usb_serial_driver ipw_device = { 444 .driver = { 445 .owner = THIS_MODULE, 446 .name = "ipw", 447 }, 448 .description = "IPWireless converter", 449 .usb_driver = &usb_ipw_driver, 450 .id_table = usb_ipw_ids, 451 .num_interrupt_in = NUM_DONT_CARE, 452 .num_bulk_in = 1, 453 .num_bulk_out = 1, 454 .num_ports = 1, 455 .open = ipw_open, 456 .close = ipw_close, 457 .port_probe = ipw_probe, 458 .port_remove = ipw_disconnect, 459 .write = ipw_write, 460 .write_bulk_callback = ipw_write_bulk_callback, 461 .read_bulk_callback = ipw_read_bulk_callback, 462 }; 463 464 465 466 static int usb_ipw_init(void) 467 { 468 int retval; 469 470 retval = usb_serial_register(&ipw_device); 471 if (retval) 472 return retval; 473 retval = usb_register(&usb_ipw_driver); 474 if (retval) { 475 usb_serial_deregister(&ipw_device); 476 return retval; 477 } 478 info(DRIVER_DESC " " DRIVER_VERSION); 479 return 0; 480 } 481 482 static void usb_ipw_exit(void) 483 { 484 usb_deregister(&usb_ipw_driver); 485 usb_serial_deregister(&ipw_device); 486 } 487 488 module_init(usb_ipw_init); 489 module_exit(usb_ipw_exit); 490 491 /* Module information */ 492 MODULE_AUTHOR( DRIVER_AUTHOR ); 493 MODULE_DESCRIPTION( DRIVER_DESC ); 494 MODULE_LICENSE("GPL"); 495 496 module_param(debug, bool, S_IRUGO | S_IWUSR); 497 MODULE_PARM_DESC(debug, "Debug enabled or not"); 498