1 /* 2 * IPWireless 3G UMTS TDD Modem driver (USB connected) 3 * 4 * Copyright (C) 2004 Roelf Diedericks <roelfd@inet.co.za> 5 * Copyright (C) 2004 Greg Kroah-Hartman <greg@kroah.com> 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License as published by 9 * the Free Software Foundation; either version 2 of the License, or 10 * (at your option) any later version. 11 * 12 * All information about the device was acquired using SnoopyPro 13 * on MSFT's O/S, and examing the MSFT drivers' debug output 14 * (insanely left _on_ in the enduser version) 15 * 16 * It was written out of frustration with the IPWireless USB modem 17 * supplied by Axity3G/Sentech South Africa not supporting 18 * Linux whatsoever. 19 * 20 * Nobody provided any proprietary information that was not already 21 * available for this device. 22 * 23 * The modem adheres to the "3GPP TS 27.007 AT command set for 3G 24 * User Equipment (UE)" standard, available from 25 * http://www.3gpp.org/ftp/Specs/html-info/27007.htm 26 * 27 * The code was only tested the IPWireless handheld modem distributed 28 * in South Africa by Sentech. 29 * 30 * It may work for Woosh Inc in .nz too, as it appears they use the 31 * same kit. 32 * 33 * There is still some work to be done in terms of handling 34 * DCD, DTR, RTS, CTS which are currently faked. 35 * It's good enough for PPP at this point. It's based off all kinds of 36 * code found in usb/serial and usb/class 37 * 38 */ 39 40 #include <linux/kernel.h> 41 #include <linux/errno.h> 42 #include <linux/init.h> 43 #include <linux/slab.h> 44 #include <linux/tty.h> 45 #include <linux/tty_flip.h> 46 #include <linux/module.h> 47 #include <linux/spinlock.h> 48 #include <linux/usb.h> 49 #include <linux/usb/serial.h> 50 #include <linux/uaccess.h> 51 52 /* 53 * Version Information 54 */ 55 #define DRIVER_VERSION "v0.3" 56 #define DRIVER_AUTHOR "Roelf Diedericks" 57 #define DRIVER_DESC "IPWireless tty driver" 58 59 #define IPW_TTY_MAJOR 240 /* real device node major id, experimental range */ 60 #define IPW_TTY_MINORS 256 /* we support 256 devices, dunno why, it'd be insane :) */ 61 62 #define USB_IPW_MAGIC 0x6d02 /* magic number for ipw struct */ 63 64 65 /* Message sizes */ 66 #define EVENT_BUFFER_SIZE 0xFF 67 #define CHAR2INT16(c1, c0) (((u32)((c1) & 0xff) << 8) + (u32)((c0) & 0xff)) 68 #define NUM_BULK_URBS 24 69 #define NUM_CONTROL_URBS 16 70 71 /* vendor/product pairs that are known work with this driver*/ 72 #define IPW_VID 0x0bc3 73 #define IPW_PID 0x0001 74 75 76 /* Vendor commands: */ 77 78 /* baud rates */ 79 enum { 80 ipw_sio_b256000 = 0x000e, 81 ipw_sio_b128000 = 0x001d, 82 ipw_sio_b115200 = 0x0020, 83 ipw_sio_b57600 = 0x0040, 84 ipw_sio_b56000 = 0x0042, 85 ipw_sio_b38400 = 0x0060, 86 ipw_sio_b19200 = 0x00c0, 87 ipw_sio_b14400 = 0x0100, 88 ipw_sio_b9600 = 0x0180, 89 ipw_sio_b4800 = 0x0300, 90 ipw_sio_b2400 = 0x0600, 91 ipw_sio_b1200 = 0x0c00, 92 ipw_sio_b600 = 0x1800 93 }; 94 95 /* data bits */ 96 #define ipw_dtb_7 0x700 97 #define ipw_dtb_8 0x810 /* ok so the define is misleading, I know, but forces 8,n,1 */ 98 /* I mean, is there a point to any other setting these days? :) */ 99 100 /* usb control request types : */ 101 #define IPW_SIO_RXCTL 0x00 /* control bulk rx channel transmissions, value=1/0 (on/off) */ 102 #define IPW_SIO_SET_BAUD 0x01 /* set baud, value=requested ipw_sio_bxxxx */ 103 #define IPW_SIO_SET_LINE 0x03 /* set databits, parity. value=ipw_dtb_x */ 104 #define IPW_SIO_SET_PIN 0x03 /* set/clear dtr/rts value=ipw_pin_xxx */ 105 #define IPW_SIO_POLL 0x08 /* get serial port status byte, call with value=0 */ 106 #define IPW_SIO_INIT 0x11 /* initializes ? value=0 (appears as first thing todo on open) */ 107 #define IPW_SIO_PURGE 0x12 /* purge all transmissions?, call with value=numchar_to_purge */ 108 #define IPW_SIO_HANDFLOW 0x13 /* set xon/xoff limits value=0, and a buffer of 0x10 bytes */ 109 #define IPW_SIO_SETCHARS 0x13 /* set the flowcontrol special chars, value=0, buf=6 bytes, */ 110 /* last 2 bytes contain flowcontrol chars e.g. 00 00 00 00 11 13 */ 111 112 /* values used for request IPW_SIO_SET_PIN */ 113 #define IPW_PIN_SETDTR 0x101 114 #define IPW_PIN_SETRTS 0x202 115 #define IPW_PIN_CLRDTR 0x100 116 #define IPW_PIN_CLRRTS 0x200 /* unconfirmed */ 117 118 /* values used for request IPW_SIO_RXCTL */ 119 #define IPW_RXBULK_ON 1 120 #define IPW_RXBULK_OFF 0 121 122 /* various 16 byte hardcoded transferbuffers used by flow control */ 123 #define IPW_BYTES_FLOWINIT { 0x01, 0, 0, 0, 0x40, 0, 0, 0, \ 124 0, 0, 0, 0, 0, 0, 0, 0 } 125 126 /* Interpretation of modem status lines */ 127 /* These need sorting out by individually connecting pins and checking 128 * results. FIXME! 129 * When data is being sent we see 0x30 in the lower byte; this must 130 * contain DSR and CTS ... 131 */ 132 #define IPW_DSR ((1<<4) | (1<<5)) 133 #define IPW_CTS ((1<<5) | (1<<4)) 134 135 #define IPW_WANTS_TO_SEND 0x30 136 137 static struct usb_device_id usb_ipw_ids[] = { 138 { USB_DEVICE(IPW_VID, IPW_PID) }, 139 { }, 140 }; 141 142 MODULE_DEVICE_TABLE(usb, usb_ipw_ids); 143 144 static struct usb_driver usb_ipw_driver = { 145 .name = "ipwtty", 146 .probe = usb_serial_probe, 147 .disconnect = usb_serial_disconnect, 148 .id_table = usb_ipw_ids, 149 .no_dynamic_id = 1, 150 }; 151 152 static int debug; 153 154 static void ipw_read_bulk_callback(struct urb *urb) 155 { 156 struct usb_serial_port *port = urb->context; 157 unsigned char *data = urb->transfer_buffer; 158 struct tty_struct *tty; 159 int result; 160 int status = urb->status; 161 162 dbg("%s - port %d", __func__, port->number); 163 164 if (status) { 165 dbg("%s - nonzero read bulk status received: %d", 166 __func__, status); 167 return; 168 } 169 170 usb_serial_debug_data(debug, &port->dev, __func__, 171 urb->actual_length, data); 172 173 tty = tty_port_tty_get(&port->port); 174 if (tty && urb->actual_length) { 175 tty_buffer_request_room(tty, urb->actual_length); 176 tty_insert_flip_string(tty, data, urb->actual_length); 177 tty_flip_buffer_push(tty); 178 } 179 tty_kref_put(tty); 180 181 /* Continue trying to always read */ 182 usb_fill_bulk_urb(port->read_urb, port->serial->dev, 183 usb_rcvbulkpipe(port->serial->dev, 184 port->bulk_in_endpointAddress), 185 port->read_urb->transfer_buffer, 186 port->read_urb->transfer_buffer_length, 187 ipw_read_bulk_callback, port); 188 result = usb_submit_urb(port->read_urb, GFP_ATOMIC); 189 if (result) 190 dev_err(&port->dev, 191 "%s - failed resubmitting read urb, error %d\n", 192 __func__, result); 193 return; 194 } 195 196 static int ipw_open(struct tty_struct *tty, struct usb_serial_port *port) 197 { 198 struct usb_device *dev = port->serial->dev; 199 u8 buf_flow_static[16] = IPW_BYTES_FLOWINIT; 200 u8 *buf_flow_init; 201 int result; 202 203 dbg("%s", __func__); 204 205 buf_flow_init = kmemdup(buf_flow_static, 16, GFP_KERNEL); 206 if (!buf_flow_init) 207 return -ENOMEM; 208 209 /* --1: Tell the modem to initialize (we think) From sniffs this is 210 * always the first thing that gets sent to the modem during 211 * opening of the device */ 212 dbg("%s: Sending SIO_INIT (we guess)", __func__); 213 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 214 IPW_SIO_INIT, 215 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 216 0, 217 0, /* index */ 218 NULL, 219 0, 220 100000); 221 if (result < 0) 222 dev_err(&port->dev, 223 "Init of modem failed (error = %d)\n", result); 224 225 /* reset the bulk pipes */ 226 usb_clear_halt(dev, 227 usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress)); 228 usb_clear_halt(dev, 229 usb_sndbulkpipe(dev, port->bulk_out_endpointAddress)); 230 231 /*--2: Start reading from the device */ 232 dbg("%s: setting up bulk read callback", __func__); 233 usb_fill_bulk_urb(port->read_urb, dev, 234 usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress), 235 port->bulk_in_buffer, 236 port->bulk_in_size, 237 ipw_read_bulk_callback, port); 238 result = usb_submit_urb(port->read_urb, GFP_KERNEL); 239 if (result < 0) 240 dbg("%s - usb_submit_urb(read bulk) failed with status %d", 241 __func__, result); 242 243 /*--3: Tell the modem to open the floodgates on the rx bulk channel */ 244 dbg("%s:asking modem for RxRead (RXBULK_ON)", __func__); 245 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 246 IPW_SIO_RXCTL, 247 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 248 IPW_RXBULK_ON, 249 0, /* index */ 250 NULL, 251 0, 252 100000); 253 if (result < 0) 254 dev_err(&port->dev, 255 "Enabling bulk RxRead failed (error = %d)\n", result); 256 257 /*--4: setup the initial flowcontrol */ 258 dbg("%s:setting init flowcontrol (%s)", __func__, buf_flow_init); 259 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 260 IPW_SIO_HANDFLOW, 261 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 262 0, 263 0, 264 buf_flow_init, 265 0x10, 266 200000); 267 if (result < 0) 268 dev_err(&port->dev, 269 "initial flowcontrol failed (error = %d)\n", result); 270 271 272 /*--5: raise the dtr */ 273 dbg("%s:raising dtr", __func__); 274 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 275 IPW_SIO_SET_PIN, 276 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 277 IPW_PIN_SETDTR, 278 0, 279 NULL, 280 0, 281 200000); 282 if (result < 0) 283 dev_err(&port->dev, 284 "setting dtr failed (error = %d)\n", result); 285 286 /*--6: raise the rts */ 287 dbg("%s:raising rts", __func__); 288 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 289 IPW_SIO_SET_PIN, 290 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 291 IPW_PIN_SETRTS, 292 0, 293 NULL, 294 0, 295 200000); 296 if (result < 0) 297 dev_err(&port->dev, 298 "setting dtr failed (error = %d)\n", result); 299 300 kfree(buf_flow_init); 301 return 0; 302 } 303 304 static void ipw_dtr_rts(struct usb_serial_port *port, int on) 305 { 306 struct usb_device *dev = port->serial->dev; 307 int result; 308 309 /*--1: drop the dtr */ 310 dbg("%s:dropping dtr", __func__); 311 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 312 IPW_SIO_SET_PIN, 313 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 314 on ? IPW_PIN_SETDTR : IPW_PIN_CLRDTR, 315 0, 316 NULL, 317 0, 318 200000); 319 if (result < 0) 320 dev_err(&port->dev, "dropping dtr failed (error = %d)\n", 321 result); 322 323 /*--2: drop the rts */ 324 dbg("%s:dropping rts", __func__); 325 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 326 IPW_SIO_SET_PIN, USB_TYPE_VENDOR | 327 USB_RECIP_INTERFACE | USB_DIR_OUT, 328 on ? IPW_PIN_SETRTS : IPW_PIN_CLRRTS, 329 0, 330 NULL, 331 0, 332 200000); 333 if (result < 0) 334 dev_err(&port->dev, 335 "dropping rts failed (error = %d)\n", result); 336 } 337 338 static void ipw_close(struct usb_serial_port *port) 339 { 340 struct usb_device *dev = port->serial->dev; 341 int result; 342 343 /*--3: purge */ 344 dbg("%s:sending purge", __func__); 345 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 346 IPW_SIO_PURGE, USB_TYPE_VENDOR | 347 USB_RECIP_INTERFACE | USB_DIR_OUT, 348 0x03, 349 0, 350 NULL, 351 0, 352 200000); 353 if (result < 0) 354 dev_err(&port->dev, "purge failed (error = %d)\n", result); 355 356 357 /* send RXBULK_off (tell modem to stop transmitting bulk data on 358 rx chan) */ 359 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 360 IPW_SIO_RXCTL, 361 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 362 IPW_RXBULK_OFF, 363 0, /* index */ 364 NULL, 365 0, 366 100000); 367 368 if (result < 0) 369 dev_err(&port->dev, 370 "Disabling bulk RxRead failed (error = %d)\n", result); 371 372 /* shutdown any in-flight urbs that we know about */ 373 usb_kill_urb(port->read_urb); 374 usb_kill_urb(port->write_urb); 375 } 376 377 static void ipw_write_bulk_callback(struct urb *urb) 378 { 379 struct usb_serial_port *port = urb->context; 380 int status = urb->status; 381 382 dbg("%s", __func__); 383 384 port->write_urb_busy = 0; 385 386 if (status) 387 dbg("%s - nonzero write bulk status received: %d", 388 __func__, status); 389 390 usb_serial_port_softint(port); 391 } 392 393 static int ipw_write(struct tty_struct *tty, struct usb_serial_port *port, 394 const unsigned char *buf, int count) 395 { 396 struct usb_device *dev = port->serial->dev; 397 int ret; 398 399 dbg("%s: TOP: count=%d, in_interrupt=%ld", __func__, 400 count, in_interrupt()); 401 402 if (count == 0) { 403 dbg("%s - write request of 0 bytes", __func__); 404 return 0; 405 } 406 407 spin_lock_bh(&port->lock); 408 if (port->write_urb_busy) { 409 spin_unlock_bh(&port->lock); 410 dbg("%s - already writing", __func__); 411 return 0; 412 } 413 port->write_urb_busy = 1; 414 spin_unlock_bh(&port->lock); 415 416 count = min(count, port->bulk_out_size); 417 memcpy(port->bulk_out_buffer, buf, count); 418 419 dbg("%s count now:%d", __func__, count); 420 421 usb_fill_bulk_urb(port->write_urb, dev, 422 usb_sndbulkpipe(dev, port->bulk_out_endpointAddress), 423 port->write_urb->transfer_buffer, 424 count, 425 ipw_write_bulk_callback, 426 port); 427 428 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 429 if (ret != 0) { 430 port->write_urb_busy = 0; 431 dbg("%s - usb_submit_urb(write bulk) failed with error = %d", 432 __func__, ret); 433 return ret; 434 } 435 436 dbg("%s returning %d", __func__, count); 437 return count; 438 } 439 440 static int ipw_probe(struct usb_serial_port *port) 441 { 442 return 0; 443 } 444 445 static int ipw_disconnect(struct usb_serial_port *port) 446 { 447 usb_set_serial_port_data(port, NULL); 448 return 0; 449 } 450 451 static struct usb_serial_driver ipw_device = { 452 .driver = { 453 .owner = THIS_MODULE, 454 .name = "ipw", 455 }, 456 .description = "IPWireless converter", 457 .usb_driver = &usb_ipw_driver, 458 .id_table = usb_ipw_ids, 459 .num_ports = 1, 460 .open = ipw_open, 461 .close = ipw_close, 462 .dtr_rts = ipw_dtr_rts, 463 .port_probe = ipw_probe, 464 .port_remove = ipw_disconnect, 465 .write = ipw_write, 466 .write_bulk_callback = ipw_write_bulk_callback, 467 .read_bulk_callback = ipw_read_bulk_callback, 468 }; 469 470 471 472 static int __init usb_ipw_init(void) 473 { 474 int retval; 475 476 retval = usb_serial_register(&ipw_device); 477 if (retval) 478 return retval; 479 retval = usb_register(&usb_ipw_driver); 480 if (retval) { 481 usb_serial_deregister(&ipw_device); 482 return retval; 483 } 484 printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":" 485 DRIVER_DESC "\n"); 486 return 0; 487 } 488 489 static void __exit usb_ipw_exit(void) 490 { 491 usb_deregister(&usb_ipw_driver); 492 usb_serial_deregister(&ipw_device); 493 } 494 495 module_init(usb_ipw_init); 496 module_exit(usb_ipw_exit); 497 498 /* Module information */ 499 MODULE_AUTHOR(DRIVER_AUTHOR); 500 MODULE_DESCRIPTION(DRIVER_DESC); 501 MODULE_LICENSE("GPL"); 502 503 module_param(debug, bool, S_IRUGO | S_IWUSR); 504 MODULE_PARM_DESC(debug, "Debug enabled or not"); 505