1 /* 2 * IPWireless 3G UMTS TDD Modem driver (USB connected) 3 * 4 * Copyright (C) 2004 Roelf Diedericks <roelfd@inet.co.za> 5 * Copyright (C) 2004 Greg Kroah-Hartman <greg@kroah.com> 6 * 7 * This program is free software; you can redistribute it and/or modify 8 * it under the terms of the GNU General Public License as published by 9 * the Free Software Foundation; either version 2 of the License, or 10 * (at your option) any later version. 11 * 12 * All information about the device was acquired using SnoopyPro 13 * on MSFT's O/S, and examing the MSFT drivers' debug output 14 * (insanely left _on_ in the enduser version) 15 * 16 * It was written out of frustration with the IPWireless USB modem 17 * supplied by Axity3G/Sentech South Africa not supporting 18 * Linux whatsoever. 19 * 20 * Nobody provided any proprietary information that was not already 21 * available for this device. 22 * 23 * The modem adheres to the "3GPP TS 27.007 AT command set for 3G 24 * User Equipment (UE)" standard, available from 25 * http://www.3gpp.org/ftp/Specs/html-info/27007.htm 26 * 27 * The code was only tested the IPWireless handheld modem distributed 28 * in South Africa by Sentech. 29 * 30 * It may work for Woosh Inc in .nz too, as it appears they use the 31 * same kit. 32 * 33 * There is still some work to be done in terms of handling 34 * DCD, DTR, RTS, CTS which are currently faked. 35 * It's good enough for PPP at this point. It's based off all kinds of 36 * code found in usb/serial and usb/class 37 * 38 */ 39 40 #include <linux/kernel.h> 41 #include <linux/errno.h> 42 #include <linux/init.h> 43 #include <linux/slab.h> 44 #include <linux/tty.h> 45 #include <linux/tty_flip.h> 46 #include <linux/module.h> 47 #include <linux/spinlock.h> 48 #include <linux/usb.h> 49 #include <linux/usb/serial.h> 50 #include <asm/uaccess.h> 51 52 /* 53 * Version Information 54 */ 55 #define DRIVER_VERSION "v0.3" 56 #define DRIVER_AUTHOR "Roelf Diedericks" 57 #define DRIVER_DESC "IPWireless tty driver" 58 59 #define IPW_TTY_MAJOR 240 /* real device node major id, experimental range */ 60 #define IPW_TTY_MINORS 256 /* we support 256 devices, dunno why, it'd be insane :) */ 61 62 #define USB_IPW_MAGIC 0x6d02 /* magic number for ipw struct */ 63 64 65 /* Message sizes */ 66 #define EVENT_BUFFER_SIZE 0xFF 67 #define CHAR2INT16(c1,c0) (((u32)((c1) & 0xff) << 8) + (u32)((c0) & 0xff)) 68 #define NUM_BULK_URBS 24 69 #define NUM_CONTROL_URBS 16 70 71 /* vendor/product pairs that are known work with this driver*/ 72 #define IPW_VID 0x0bc3 73 #define IPW_PID 0x0001 74 75 76 /* Vendor commands: */ 77 78 /* baud rates */ 79 enum { 80 ipw_sio_b256000 = 0x000e, 81 ipw_sio_b128000 = 0x001d, 82 ipw_sio_b115200 = 0x0020, 83 ipw_sio_b57600 = 0x0040, 84 ipw_sio_b56000 = 0x0042, 85 ipw_sio_b38400 = 0x0060, 86 ipw_sio_b19200 = 0x00c0, 87 ipw_sio_b14400 = 0x0100, 88 ipw_sio_b9600 = 0x0180, 89 ipw_sio_b4800 = 0x0300, 90 ipw_sio_b2400 = 0x0600, 91 ipw_sio_b1200 = 0x0c00, 92 ipw_sio_b600 = 0x1800 93 }; 94 95 /* data bits */ 96 #define ipw_dtb_7 0x700 97 #define ipw_dtb_8 0x810 // ok so the define is misleading, I know, but forces 8,n,1 98 // I mean, is there a point to any other setting these days? :) 99 100 /* usb control request types : */ 101 #define IPW_SIO_RXCTL 0x00 // control bulk rx channel transmissions, value=1/0 (on/off) 102 #define IPW_SIO_SET_BAUD 0x01 // set baud, value=requested ipw_sio_bxxxx 103 #define IPW_SIO_SET_LINE 0x03 // set databits, parity. value=ipw_dtb_x 104 #define IPW_SIO_SET_PIN 0x03 // set/clear dtr/rts value=ipw_pin_xxx 105 #define IPW_SIO_POLL 0x08 // get serial port status byte, call with value=0 106 #define IPW_SIO_INIT 0x11 // initializes ? value=0 (appears as first thing todo on open) 107 #define IPW_SIO_PURGE 0x12 // purge all transmissions?, call with value=numchar_to_purge 108 #define IPW_SIO_HANDFLOW 0x13 // set xon/xoff limits value=0, and a buffer of 0x10 bytes 109 #define IPW_SIO_SETCHARS 0x13 // set the flowcontrol special chars, value=0, buf=6 bytes, 110 // last 2 bytes contain flowcontrol chars e.g. 00 00 00 00 11 13 111 112 /* values used for request IPW_SIO_SET_PIN */ 113 #define IPW_PIN_SETDTR 0x101 114 #define IPW_PIN_SETRTS 0x202 115 #define IPW_PIN_CLRDTR 0x100 116 #define IPW_PIN_CLRRTS 0x200 // unconfirmed 117 118 /* values used for request IPW_SIO_RXCTL */ 119 #define IPW_RXBULK_ON 1 120 #define IPW_RXBULK_OFF 0 121 122 /* various 16 byte hardcoded transferbuffers used by flow control */ 123 #define IPW_BYTES_FLOWINIT { 0x01, 0, 0, 0, 0x40, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 } 124 125 /* Interpretation of modem status lines */ 126 /* These need sorting out by individually connecting pins and checking 127 * results. FIXME! 128 * When data is being sent we see 0x30 in the lower byte; this must 129 * contain DSR and CTS ... 130 */ 131 #define IPW_DSR ((1<<4) | (1<<5)) 132 #define IPW_CTS ((1<<5) | (1<<4)) 133 134 #define IPW_WANTS_TO_SEND 0x30 135 //#define IPW_DTR /* Data Terminal Ready */ 136 //#define IPW_CTS /* Clear To Send */ 137 //#define IPW_CD /* Carrier Detect */ 138 //#define IPW_DSR /* Data Set Ready */ 139 //#define IPW_RxD /* Receive pin */ 140 141 //#define IPW_LE 142 //#define IPW_RTS 143 //#define IPW_ST 144 //#define IPW_SR 145 //#define IPW_RI /* Ring Indicator */ 146 147 static struct usb_device_id usb_ipw_ids[] = { 148 { USB_DEVICE(IPW_VID, IPW_PID) }, 149 { }, 150 }; 151 152 MODULE_DEVICE_TABLE(usb, usb_ipw_ids); 153 154 static struct usb_driver usb_ipw_driver = { 155 .name = "ipwtty", 156 .probe = usb_serial_probe, 157 .disconnect = usb_serial_disconnect, 158 .id_table = usb_ipw_ids, 159 .no_dynamic_id = 1, 160 }; 161 162 static int debug; 163 164 static void ipw_read_bulk_callback(struct urb *urb) 165 { 166 struct usb_serial_port *port = urb->context; 167 unsigned char *data = urb->transfer_buffer; 168 struct tty_struct *tty; 169 int result; 170 171 dbg("%s - port %d", __FUNCTION__, port->number); 172 173 if (urb->status) { 174 dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status); 175 return; 176 } 177 178 usb_serial_debug_data(debug, &port->dev, __FUNCTION__, urb->actual_length, data); 179 180 tty = port->tty; 181 if (tty && urb->actual_length) { 182 tty_buffer_request_room(tty, urb->actual_length); 183 tty_insert_flip_string(tty, data, urb->actual_length); 184 tty_flip_buffer_push(tty); 185 } 186 187 /* Continue trying to always read */ 188 usb_fill_bulk_urb (port->read_urb, port->serial->dev, 189 usb_rcvbulkpipe(port->serial->dev, 190 port->bulk_in_endpointAddress), 191 port->read_urb->transfer_buffer, 192 port->read_urb->transfer_buffer_length, 193 ipw_read_bulk_callback, port); 194 result = usb_submit_urb(port->read_urb, GFP_ATOMIC); 195 if (result) 196 dev_err(&port->dev, "%s - failed resubmitting read urb, error %d\n", __FUNCTION__, result); 197 return; 198 } 199 200 static int ipw_open(struct usb_serial_port *port, struct file *filp) 201 { 202 struct usb_device *dev = port->serial->dev; 203 u8 buf_flow_static[16] = IPW_BYTES_FLOWINIT; 204 u8 *buf_flow_init; 205 int result; 206 207 dbg("%s", __FUNCTION__); 208 209 buf_flow_init = kmemdup(buf_flow_static, 16, GFP_KERNEL); 210 if (!buf_flow_init) 211 return -ENOMEM; 212 213 if (port->tty) 214 port->tty->low_latency = 1; 215 216 /* --1: Tell the modem to initialize (we think) From sniffs this is always the 217 * first thing that gets sent to the modem during opening of the device */ 218 dbg("%s: Sending SIO_INIT (we guess)",__FUNCTION__); 219 result = usb_control_msg(dev, usb_sndctrlpipe(dev,0), 220 IPW_SIO_INIT, 221 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 222 0, 223 0, /* index */ 224 NULL, 225 0, 226 100000); 227 if (result < 0) 228 dev_err(&port->dev, "Init of modem failed (error = %d)", result); 229 230 /* reset the bulk pipes */ 231 usb_clear_halt(dev, usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress)); 232 usb_clear_halt(dev, usb_sndbulkpipe(dev, port->bulk_out_endpointAddress)); 233 234 /*--2: Start reading from the device */ 235 dbg("%s: setting up bulk read callback",__FUNCTION__); 236 usb_fill_bulk_urb(port->read_urb, dev, 237 usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress), 238 port->bulk_in_buffer, 239 port->bulk_in_size, 240 ipw_read_bulk_callback, port); 241 result = usb_submit_urb(port->read_urb, GFP_KERNEL); 242 if (result < 0) 243 dbg("%s - usb_submit_urb(read bulk) failed with status %d", __FUNCTION__, result); 244 245 /*--3: Tell the modem to open the floodgates on the rx bulk channel */ 246 dbg("%s:asking modem for RxRead (RXBULK_ON)",__FUNCTION__); 247 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 248 IPW_SIO_RXCTL, 249 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 250 IPW_RXBULK_ON, 251 0, /* index */ 252 NULL, 253 0, 254 100000); 255 if (result < 0) 256 dev_err(&port->dev, "Enabling bulk RxRead failed (error = %d)", result); 257 258 /*--4: setup the initial flowcontrol */ 259 dbg("%s:setting init flowcontrol (%s)",__FUNCTION__,buf_flow_init); 260 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 261 IPW_SIO_HANDFLOW, 262 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 263 0, 264 0, 265 buf_flow_init, 266 0x10, 267 200000); 268 if (result < 0) 269 dev_err(&port->dev, "initial flowcontrol failed (error = %d)", result); 270 271 272 /*--5: raise the dtr */ 273 dbg("%s:raising dtr",__FUNCTION__); 274 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 275 IPW_SIO_SET_PIN, 276 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 277 IPW_PIN_SETDTR, 278 0, 279 NULL, 280 0, 281 200000); 282 if (result < 0) 283 dev_err(&port->dev, "setting dtr failed (error = %d)", result); 284 285 /*--6: raise the rts */ 286 dbg("%s:raising rts",__FUNCTION__); 287 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 288 IPW_SIO_SET_PIN, 289 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 290 IPW_PIN_SETRTS, 291 0, 292 NULL, 293 0, 294 200000); 295 if (result < 0) 296 dev_err(&port->dev, "setting dtr failed (error = %d)", result); 297 298 kfree(buf_flow_init); 299 return 0; 300 } 301 302 static void ipw_close(struct usb_serial_port *port, struct file * filp) 303 { 304 struct usb_device *dev = port->serial->dev; 305 int result; 306 307 if (tty_hung_up_p(filp)) { 308 dbg("%s: tty_hung_up_p ...", __FUNCTION__); 309 return; 310 } 311 312 /*--1: drop the dtr */ 313 dbg("%s:dropping dtr",__FUNCTION__); 314 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 315 IPW_SIO_SET_PIN, 316 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 317 IPW_PIN_CLRDTR, 318 0, 319 NULL, 320 0, 321 200000); 322 if (result < 0) 323 dev_err(&port->dev, "dropping dtr failed (error = %d)", result); 324 325 /*--2: drop the rts */ 326 dbg("%s:dropping rts",__FUNCTION__); 327 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 328 IPW_SIO_SET_PIN, USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 329 IPW_PIN_CLRRTS, 330 0, 331 NULL, 332 0, 333 200000); 334 if (result < 0) 335 dev_err(&port->dev, "dropping rts failed (error = %d)", result); 336 337 338 /*--3: purge */ 339 dbg("%s:sending purge",__FUNCTION__); 340 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 341 IPW_SIO_PURGE, USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 342 0x03, 343 0, 344 NULL, 345 0, 346 200000); 347 if (result < 0) 348 dev_err(&port->dev, "purge failed (error = %d)", result); 349 350 351 /* send RXBULK_off (tell modem to stop transmitting bulk data on rx chan) */ 352 result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 353 IPW_SIO_RXCTL, 354 USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT, 355 IPW_RXBULK_OFF, 356 0, /* index */ 357 NULL, 358 0, 359 100000); 360 361 if (result < 0) 362 dev_err(&port->dev, "Disabling bulk RxRead failed (error = %d)", result); 363 364 /* shutdown any in-flight urbs that we know about */ 365 usb_kill_urb(port->read_urb); 366 usb_kill_urb(port->write_urb); 367 } 368 369 static void ipw_write_bulk_callback(struct urb *urb) 370 { 371 struct usb_serial_port *port = urb->context; 372 373 dbg("%s", __FUNCTION__); 374 375 port->write_urb_busy = 0; 376 377 if (urb->status) 378 dbg("%s - nonzero write bulk status received: %d", __FUNCTION__, urb->status); 379 380 usb_serial_port_softint(port); 381 } 382 383 static int ipw_write(struct usb_serial_port *port, const unsigned char *buf, int count) 384 { 385 struct usb_device *dev = port->serial->dev; 386 int ret; 387 388 dbg("%s: TOP: count=%d, in_interrupt=%ld", __FUNCTION__, 389 count, in_interrupt() ); 390 391 if (count == 0) { 392 dbg("%s - write request of 0 bytes", __FUNCTION__); 393 return 0; 394 } 395 396 spin_lock_bh(&port->lock); 397 if (port->write_urb_busy) { 398 spin_unlock_bh(&port->lock); 399 dbg("%s - already writing", __FUNCTION__); 400 return 0; 401 } 402 port->write_urb_busy = 1; 403 spin_unlock_bh(&port->lock); 404 405 count = min(count, port->bulk_out_size); 406 memcpy(port->bulk_out_buffer, buf, count); 407 408 dbg("%s count now:%d", __FUNCTION__, count); 409 410 usb_fill_bulk_urb(port->write_urb, dev, 411 usb_sndbulkpipe(dev, port->bulk_out_endpointAddress), 412 port->write_urb->transfer_buffer, 413 count, 414 ipw_write_bulk_callback, 415 port); 416 417 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 418 if (ret != 0) { 419 port->write_urb_busy = 0; 420 dbg("%s - usb_submit_urb(write bulk) failed with error = %d", __FUNCTION__, ret); 421 return ret; 422 } 423 424 dbg("%s returning %d", __FUNCTION__, count); 425 return count; 426 } 427 428 static int ipw_probe(struct usb_serial_port *port) 429 { 430 return 0; 431 } 432 433 static int ipw_disconnect(struct usb_serial_port *port) 434 { 435 usb_set_serial_port_data(port, NULL); 436 return 0; 437 } 438 439 static struct usb_serial_driver ipw_device = { 440 .driver = { 441 .owner = THIS_MODULE, 442 .name = "ipw", 443 }, 444 .description = "IPWireless converter", 445 .usb_driver = &usb_ipw_driver, 446 .id_table = usb_ipw_ids, 447 .num_interrupt_in = NUM_DONT_CARE, 448 .num_bulk_in = 1, 449 .num_bulk_out = 1, 450 .num_ports = 1, 451 .open = ipw_open, 452 .close = ipw_close, 453 .port_probe = ipw_probe, 454 .port_remove = ipw_disconnect, 455 .write = ipw_write, 456 .write_bulk_callback = ipw_write_bulk_callback, 457 .read_bulk_callback = ipw_read_bulk_callback, 458 }; 459 460 461 462 static int usb_ipw_init(void) 463 { 464 int retval; 465 466 retval = usb_serial_register(&ipw_device); 467 if (retval) 468 return retval; 469 retval = usb_register(&usb_ipw_driver); 470 if (retval) { 471 usb_serial_deregister(&ipw_device); 472 return retval; 473 } 474 info(DRIVER_DESC " " DRIVER_VERSION); 475 return 0; 476 } 477 478 static void usb_ipw_exit(void) 479 { 480 usb_deregister(&usb_ipw_driver); 481 usb_serial_deregister(&ipw_device); 482 } 483 484 module_init(usb_ipw_init); 485 module_exit(usb_ipw_exit); 486 487 /* Module information */ 488 MODULE_AUTHOR( DRIVER_AUTHOR ); 489 MODULE_DESCRIPTION( DRIVER_DESC ); 490 MODULE_LICENSE("GPL"); 491 492 module_param(debug, bool, S_IRUGO | S_IWUSR); 493 MODULE_PARM_DESC(debug, "Debug enabled or not"); 494