1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Edgeport USB Serial Converter driver 4 * 5 * Copyright (C) 2000-2002 Inside Out Networks, All rights reserved. 6 * Copyright (C) 2001-2002 Greg Kroah-Hartman <greg@kroah.com> 7 * 8 * Supports the following devices: 9 * EP/1 EP/2 EP/4 EP/21 EP/22 EP/221 EP/42 EP/421 WATCHPORT 10 * 11 * For questions or problems with this driver, contact Inside Out 12 * Networks technical support, or Peter Berger <pberger@brimson.com>, 13 * or Al Borchers <alborchers@steinerpoint.com>. 14 */ 15 16 #include <linux/kernel.h> 17 #include <linux/jiffies.h> 18 #include <linux/errno.h> 19 #include <linux/slab.h> 20 #include <linux/tty.h> 21 #include <linux/tty_driver.h> 22 #include <linux/tty_flip.h> 23 #include <linux/module.h> 24 #include <linux/spinlock.h> 25 #include <linux/mutex.h> 26 #include <linux/serial.h> 27 #include <linux/swab.h> 28 #include <linux/kfifo.h> 29 #include <linux/ioctl.h> 30 #include <linux/firmware.h> 31 #include <linux/uaccess.h> 32 #include <linux/usb.h> 33 #include <linux/usb/serial.h> 34 35 #include "io_16654.h" 36 #include "io_usbvend.h" 37 #include "io_ti.h" 38 39 #define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com> and David Iacovelli" 40 #define DRIVER_DESC "Edgeport USB Serial Driver" 41 42 #define EPROM_PAGE_SIZE 64 43 44 45 /* different hardware types */ 46 #define HARDWARE_TYPE_930 0 47 #define HARDWARE_TYPE_TIUMP 1 48 49 /* IOCTL_PRIVATE_TI_GET_MODE Definitions */ 50 #define TI_MODE_CONFIGURING 0 /* Device has not entered start device */ 51 #define TI_MODE_BOOT 1 /* Staying in boot mode */ 52 #define TI_MODE_DOWNLOAD 2 /* Made it to download mode */ 53 #define TI_MODE_TRANSITIONING 3 /* 54 * Currently in boot mode but 55 * transitioning to download mode 56 */ 57 58 /* read urb state */ 59 #define EDGE_READ_URB_RUNNING 0 60 #define EDGE_READ_URB_STOPPING 1 61 #define EDGE_READ_URB_STOPPED 2 62 63 64 /* Product information read from the Edgeport */ 65 struct product_info { 66 int TiMode; /* Current TI Mode */ 67 u8 hardware_type; /* Type of hardware */ 68 } __packed; 69 70 /* 71 * Edgeport firmware header 72 * 73 * "build_number" has been set to 0 in all three of the images I have 74 * seen, and Digi Tech Support suggests that it is safe to ignore it. 75 * 76 * "length" is the number of bytes of actual data following the header. 77 * 78 * "checksum" is the low order byte resulting from adding the values of 79 * all the data bytes. 80 */ 81 struct edgeport_fw_hdr { 82 u8 major_version; 83 u8 minor_version; 84 __le16 build_number; 85 __le16 length; 86 u8 checksum; 87 } __packed; 88 89 struct edgeport_port { 90 u16 uart_base; 91 u16 dma_address; 92 u8 shadow_msr; 93 u8 shadow_mcr; 94 u8 shadow_lsr; 95 u8 lsr_mask; 96 u32 ump_read_timeout; /* 97 * Number of milliseconds the UMP will 98 * wait without data before completing 99 * a read short 100 */ 101 int baud_rate; 102 int close_pending; 103 int lsr_event; 104 105 struct edgeport_serial *edge_serial; 106 struct usb_serial_port *port; 107 u8 bUartMode; /* Port type, 0: RS232, etc. */ 108 spinlock_t ep_lock; 109 int ep_read_urb_state; 110 int ep_write_urb_in_use; 111 }; 112 113 struct edgeport_serial { 114 struct product_info product_info; 115 u8 TI_I2C_Type; /* Type of I2C in UMP */ 116 u8 TiReadI2C; /* 117 * Set to TRUE if we have read the 118 * I2c in Boot Mode 119 */ 120 struct mutex es_lock; 121 int num_ports_open; 122 struct usb_serial *serial; 123 struct delayed_work heartbeat_work; 124 int fw_version; 125 bool use_heartbeat; 126 }; 127 128 129 /* Devices that this driver supports */ 130 static const struct usb_device_id edgeport_1port_id_table[] = { 131 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) }, 132 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) }, 133 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) }, 134 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) }, 135 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) }, 136 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) }, 137 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) }, 138 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) }, 139 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) }, 140 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) }, 141 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) }, 142 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) }, 143 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) }, 144 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) }, 145 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) }, 146 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) }, 147 { } 148 }; 149 150 static const struct usb_device_id edgeport_2port_id_table[] = { 151 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) }, 152 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) }, 153 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) }, 154 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) }, 155 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) }, 156 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) }, 157 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) }, 158 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) }, 159 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) }, 160 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) }, 161 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) }, 162 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) }, 163 /* The 4, 8 and 16 port devices show up as multiple 2 port devices */ 164 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) }, 165 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) }, 166 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) }, 167 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) }, 168 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) }, 169 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_E5805A) }, 170 { } 171 }; 172 173 /* Devices that this driver supports */ 174 static const struct usb_device_id id_table_combined[] = { 175 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_1) }, 176 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1) }, 177 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I) }, 178 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROXIMITY) }, 179 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOTION) }, 180 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_MOISTURE) }, 181 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_TEMPERATURE) }, 182 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_HUMIDITY) }, 183 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_POWER) }, 184 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_LIGHT) }, 185 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_RADIATION) }, 186 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_DISTANCE) }, 187 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_ACCELERATION) }, 188 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_WP_PROX_DIST) }, 189 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_HP4CD) }, 190 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_PLUS_PWR_PCI) }, 191 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2) }, 192 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2C) }, 193 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_2I) }, 194 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_421) }, 195 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21) }, 196 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_42) }, 197 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4) }, 198 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4I) }, 199 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22I) }, 200 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_221C) }, 201 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_22C) }, 202 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_21C) }, 203 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_4S) }, 204 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8) }, 205 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_8S) }, 206 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416) }, 207 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_TI_EDGEPORT_416B) }, 208 { USB_DEVICE(USB_VENDOR_ID_ION, ION_DEVICE_ID_E5805A) }, 209 { } 210 }; 211 212 MODULE_DEVICE_TABLE(usb, id_table_combined); 213 214 static bool ignore_cpu_rev; 215 static int default_uart_mode; /* RS232 */ 216 217 static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, 218 int length); 219 220 static void stop_read(struct edgeport_port *edge_port); 221 static int restart_read(struct edgeport_port *edge_port); 222 223 static void edge_set_termios(struct tty_struct *tty, 224 struct usb_serial_port *port, struct ktermios *old_termios); 225 static void edge_send(struct usb_serial_port *port, struct tty_struct *tty); 226 227 static int do_download_mode(struct edgeport_serial *serial, 228 const struct firmware *fw); 229 static int do_boot_mode(struct edgeport_serial *serial, 230 const struct firmware *fw); 231 232 /* sysfs attributes */ 233 static int edge_create_sysfs_attrs(struct usb_serial_port *port); 234 static int edge_remove_sysfs_attrs(struct usb_serial_port *port); 235 236 /* 237 * Some release of Edgeport firmware "down3.bin" after version 4.80 238 * introduced code to automatically disconnect idle devices on some 239 * Edgeport models after periods of inactivity, typically ~60 seconds. 240 * This occurs without regard to whether ports on the device are open 241 * or not. Digi International Tech Support suggested: 242 * 243 * 1. Adding driver "heartbeat" code to reset the firmware timer by 244 * requesting a descriptor record every 15 seconds, which should be 245 * effective with newer firmware versions that require it, and benign 246 * with older versions that do not. In practice 40 seconds seems often 247 * enough. 248 * 2. The heartbeat code is currently required only on Edgeport/416 models. 249 */ 250 #define FW_HEARTBEAT_VERSION_CUTOFF ((4 << 8) + 80) 251 #define FW_HEARTBEAT_SECS 40 252 253 /* Timeouts in msecs: firmware downloads take longer */ 254 #define TI_VSEND_TIMEOUT_DEFAULT 1000 255 #define TI_VSEND_TIMEOUT_FW_DOWNLOAD 10000 256 257 static int ti_vread_sync(struct usb_device *dev, u8 request, u16 value, 258 u16 index, void *data, int size) 259 { 260 int status; 261 262 status = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), request, 263 (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN), 264 value, index, data, size, 1000); 265 if (status < 0) 266 return status; 267 if (status != size) { 268 dev_dbg(&dev->dev, "%s - wanted to read %d, but only read %d\n", 269 __func__, size, status); 270 return -ECOMM; 271 } 272 return 0; 273 } 274 275 static int ti_vsend_sync(struct usb_device *dev, u8 request, u16 value, 276 u16 index, void *data, int size, int timeout) 277 { 278 int status; 279 280 status = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), request, 281 (USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT), 282 value, index, data, size, timeout); 283 if (status < 0) 284 return status; 285 286 return 0; 287 } 288 289 static int read_port_cmd(struct usb_serial_port *port, u8 command, u16 value, 290 void *data, int size) 291 { 292 return ti_vread_sync(port->serial->dev, command, value, 293 UMPM_UART1_PORT + port->port_number, 294 data, size); 295 } 296 297 static int send_port_cmd(struct usb_serial_port *port, u8 command, u16 value, 298 void *data, int size) 299 { 300 return ti_vsend_sync(port->serial->dev, command, value, 301 UMPM_UART1_PORT + port->port_number, 302 data, size, TI_VSEND_TIMEOUT_DEFAULT); 303 } 304 305 /* clear tx/rx buffers and fifo in TI UMP */ 306 static int purge_port(struct usb_serial_port *port, u16 mask) 307 { 308 int port_number = port->port_number; 309 310 dev_dbg(&port->dev, "%s - port %d, mask %x\n", __func__, port_number, mask); 311 312 return send_port_cmd(port, UMPC_PURGE_PORT, mask, NULL, 0); 313 } 314 315 /** 316 * read_download_mem - Read edgeport memory from TI chip 317 * @dev: usb device pointer 318 * @start_address: Device CPU address at which to read 319 * @length: Length of above data 320 * @address_type: Can read both XDATA and I2C 321 * @buffer: pointer to input data buffer 322 */ 323 static int read_download_mem(struct usb_device *dev, int start_address, 324 int length, u8 address_type, u8 *buffer) 325 { 326 int status = 0; 327 u8 read_length; 328 u16 be_start_address; 329 330 dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, length); 331 332 /* 333 * Read in blocks of 64 bytes 334 * (TI firmware can't handle more than 64 byte reads) 335 */ 336 while (length) { 337 if (length > 64) 338 read_length = 64; 339 else 340 read_length = (u8)length; 341 342 if (read_length > 1) { 343 dev_dbg(&dev->dev, "%s - @ %x for %d\n", __func__, start_address, read_length); 344 } 345 /* 346 * NOTE: Must use swab as wIndex is sent in little-endian 347 * byte order regardless of host byte order. 348 */ 349 be_start_address = swab16((u16)start_address); 350 status = ti_vread_sync(dev, UMPC_MEMORY_READ, 351 (u16)address_type, 352 be_start_address, 353 buffer, read_length); 354 355 if (status) { 356 dev_dbg(&dev->dev, "%s - ERROR %x\n", __func__, status); 357 return status; 358 } 359 360 if (read_length > 1) 361 usb_serial_debug_data(&dev->dev, __func__, read_length, buffer); 362 363 /* Update pointers/length */ 364 start_address += read_length; 365 buffer += read_length; 366 length -= read_length; 367 } 368 369 return status; 370 } 371 372 static int read_ram(struct usb_device *dev, int start_address, 373 int length, u8 *buffer) 374 { 375 return read_download_mem(dev, start_address, length, 376 DTK_ADDR_SPACE_XDATA, buffer); 377 } 378 379 /* Read edgeport memory to a given block */ 380 static int read_boot_mem(struct edgeport_serial *serial, 381 int start_address, int length, u8 *buffer) 382 { 383 int status = 0; 384 int i; 385 386 for (i = 0; i < length; i++) { 387 status = ti_vread_sync(serial->serial->dev, 388 UMPC_MEMORY_READ, serial->TI_I2C_Type, 389 (u16)(start_address+i), &buffer[i], 0x01); 390 if (status) { 391 dev_dbg(&serial->serial->dev->dev, "%s - ERROR %x\n", __func__, status); 392 return status; 393 } 394 } 395 396 dev_dbg(&serial->serial->dev->dev, "%s - start_address = %x, length = %d\n", 397 __func__, start_address, length); 398 usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer); 399 400 serial->TiReadI2C = 1; 401 402 return status; 403 } 404 405 /* Write given block to TI EPROM memory */ 406 static int write_boot_mem(struct edgeport_serial *serial, 407 int start_address, int length, u8 *buffer) 408 { 409 int status = 0; 410 int i; 411 u8 *temp; 412 413 /* Must do a read before write */ 414 if (!serial->TiReadI2C) { 415 temp = kmalloc(1, GFP_KERNEL); 416 if (!temp) 417 return -ENOMEM; 418 419 status = read_boot_mem(serial, 0, 1, temp); 420 kfree(temp); 421 if (status) 422 return status; 423 } 424 425 for (i = 0; i < length; ++i) { 426 status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, 427 buffer[i], (u16)(i + start_address), NULL, 428 0, TI_VSEND_TIMEOUT_DEFAULT); 429 if (status) 430 return status; 431 } 432 433 dev_dbg(&serial->serial->dev->dev, "%s - start_sddr = %x, length = %d\n", __func__, start_address, length); 434 usb_serial_debug_data(&serial->serial->dev->dev, __func__, length, buffer); 435 436 return status; 437 } 438 439 /* Write edgeport I2C memory to TI chip */ 440 static int write_i2c_mem(struct edgeport_serial *serial, 441 int start_address, int length, u8 address_type, u8 *buffer) 442 { 443 struct device *dev = &serial->serial->dev->dev; 444 int status = 0; 445 int write_length; 446 u16 be_start_address; 447 448 /* We can only send a maximum of 1 aligned byte page at a time */ 449 450 /* calculate the number of bytes left in the first page */ 451 write_length = EPROM_PAGE_SIZE - 452 (start_address & (EPROM_PAGE_SIZE - 1)); 453 454 if (write_length > length) 455 write_length = length; 456 457 dev_dbg(dev, "%s - BytesInFirstPage Addr = %x, length = %d\n", 458 __func__, start_address, write_length); 459 usb_serial_debug_data(dev, __func__, write_length, buffer); 460 461 /* 462 * Write first page. 463 * 464 * NOTE: Must use swab as wIndex is sent in little-endian byte order 465 * regardless of host byte order. 466 */ 467 be_start_address = swab16((u16)start_address); 468 status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, 469 (u16)address_type, be_start_address, 470 buffer, write_length, TI_VSEND_TIMEOUT_DEFAULT); 471 if (status) { 472 dev_dbg(dev, "%s - ERROR %d\n", __func__, status); 473 return status; 474 } 475 476 length -= write_length; 477 start_address += write_length; 478 buffer += write_length; 479 480 /* 481 * We should be aligned now -- can write max page size bytes at a 482 * time. 483 */ 484 while (length) { 485 if (length > EPROM_PAGE_SIZE) 486 write_length = EPROM_PAGE_SIZE; 487 else 488 write_length = length; 489 490 dev_dbg(dev, "%s - Page Write Addr = %x, length = %d\n", 491 __func__, start_address, write_length); 492 usb_serial_debug_data(dev, __func__, write_length, buffer); 493 494 /* 495 * Write next page. 496 * 497 * NOTE: Must use swab as wIndex is sent in little-endian byte 498 * order regardless of host byte order. 499 */ 500 be_start_address = swab16((u16)start_address); 501 status = ti_vsend_sync(serial->serial->dev, UMPC_MEMORY_WRITE, 502 (u16)address_type, be_start_address, buffer, 503 write_length, TI_VSEND_TIMEOUT_DEFAULT); 504 if (status) { 505 dev_err(dev, "%s - ERROR %d\n", __func__, status); 506 return status; 507 } 508 509 length -= write_length; 510 start_address += write_length; 511 buffer += write_length; 512 } 513 return status; 514 } 515 516 /* 517 * Examine the UMP DMA registers and LSR 518 * 519 * Check the MSBit of the X and Y DMA byte count registers. 520 * A zero in this bit indicates that the TX DMA buffers are empty 521 * then check the TX Empty bit in the UART. 522 */ 523 static int tx_active(struct edgeport_port *port) 524 { 525 int status; 526 struct out_endpoint_desc_block *oedb; 527 u8 *lsr; 528 int bytes_left = 0; 529 530 oedb = kmalloc(sizeof(*oedb), GFP_KERNEL); 531 if (!oedb) 532 return -ENOMEM; 533 534 /* 535 * Sigh, that's right, just one byte, as not all platforms can 536 * do DMA from stack 537 */ 538 lsr = kmalloc(1, GFP_KERNEL); 539 if (!lsr) { 540 kfree(oedb); 541 return -ENOMEM; 542 } 543 /* Read the DMA Count Registers */ 544 status = read_ram(port->port->serial->dev, port->dma_address, 545 sizeof(*oedb), (void *)oedb); 546 if (status) 547 goto exit_is_tx_active; 548 549 dev_dbg(&port->port->dev, "%s - XByteCount 0x%X\n", __func__, oedb->XByteCount); 550 551 /* and the LSR */ 552 status = read_ram(port->port->serial->dev, 553 port->uart_base + UMPMEM_OFFS_UART_LSR, 1, lsr); 554 555 if (status) 556 goto exit_is_tx_active; 557 dev_dbg(&port->port->dev, "%s - LSR = 0x%X\n", __func__, *lsr); 558 559 /* If either buffer has data or we are transmitting then return TRUE */ 560 if ((oedb->XByteCount & 0x80) != 0) 561 bytes_left += 64; 562 563 if ((*lsr & UMP_UART_LSR_TX_MASK) == 0) 564 bytes_left += 1; 565 566 /* We return Not Active if we get any kind of error */ 567 exit_is_tx_active: 568 dev_dbg(&port->port->dev, "%s - return %d\n", __func__, bytes_left); 569 570 kfree(lsr); 571 kfree(oedb); 572 return bytes_left; 573 } 574 575 static int choose_config(struct usb_device *dev) 576 { 577 /* 578 * There may be multiple configurations on this device, in which case 579 * we would need to read and parse all of them to find out which one 580 * we want. However, we just support one config at this point, 581 * configuration # 1, which is Config Descriptor 0. 582 */ 583 584 dev_dbg(&dev->dev, "%s - Number of Interfaces = %d\n", 585 __func__, dev->config->desc.bNumInterfaces); 586 dev_dbg(&dev->dev, "%s - MAX Power = %d\n", 587 __func__, dev->config->desc.bMaxPower * 2); 588 589 if (dev->config->desc.bNumInterfaces != 1) { 590 dev_err(&dev->dev, "%s - bNumInterfaces is not 1, ERROR!\n", __func__); 591 return -ENODEV; 592 } 593 594 return 0; 595 } 596 597 static int read_rom(struct edgeport_serial *serial, 598 int start_address, int length, u8 *buffer) 599 { 600 int status; 601 602 if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) { 603 status = read_download_mem(serial->serial->dev, 604 start_address, 605 length, 606 serial->TI_I2C_Type, 607 buffer); 608 } else { 609 status = read_boot_mem(serial, start_address, length, 610 buffer); 611 } 612 return status; 613 } 614 615 static int write_rom(struct edgeport_serial *serial, int start_address, 616 int length, u8 *buffer) 617 { 618 if (serial->product_info.TiMode == TI_MODE_BOOT) 619 return write_boot_mem(serial, start_address, length, 620 buffer); 621 622 if (serial->product_info.TiMode == TI_MODE_DOWNLOAD) 623 return write_i2c_mem(serial, start_address, length, 624 serial->TI_I2C_Type, buffer); 625 return -EINVAL; 626 } 627 628 /* Read a descriptor header from I2C based on type */ 629 static int get_descriptor_addr(struct edgeport_serial *serial, 630 int desc_type, struct ti_i2c_desc *rom_desc) 631 { 632 int start_address; 633 int status; 634 635 /* Search for requested descriptor in I2C */ 636 start_address = 2; 637 do { 638 status = read_rom(serial, 639 start_address, 640 sizeof(struct ti_i2c_desc), 641 (u8 *)rom_desc); 642 if (status) 643 return 0; 644 645 if (rom_desc->Type == desc_type) 646 return start_address; 647 648 start_address = start_address + sizeof(struct ti_i2c_desc) + 649 le16_to_cpu(rom_desc->Size); 650 651 } while ((start_address < TI_MAX_I2C_SIZE) && rom_desc->Type); 652 653 return 0; 654 } 655 656 /* Validate descriptor checksum */ 657 static int valid_csum(struct ti_i2c_desc *rom_desc, u8 *buffer) 658 { 659 u16 i; 660 u8 cs = 0; 661 662 for (i = 0; i < le16_to_cpu(rom_desc->Size); i++) 663 cs = (u8)(cs + buffer[i]); 664 665 if (cs != rom_desc->CheckSum) { 666 pr_debug("%s - Mismatch %x - %x", __func__, rom_desc->CheckSum, cs); 667 return -EINVAL; 668 } 669 return 0; 670 } 671 672 /* Make sure that the I2C image is good */ 673 static int check_i2c_image(struct edgeport_serial *serial) 674 { 675 struct device *dev = &serial->serial->dev->dev; 676 int status = 0; 677 struct ti_i2c_desc *rom_desc; 678 int start_address = 2; 679 u8 *buffer; 680 u16 ttype; 681 682 rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); 683 if (!rom_desc) 684 return -ENOMEM; 685 686 buffer = kmalloc(TI_MAX_I2C_SIZE, GFP_KERNEL); 687 if (!buffer) { 688 kfree(rom_desc); 689 return -ENOMEM; 690 } 691 692 /* Read the first byte (Signature0) must be 0x52 or 0x10 */ 693 status = read_rom(serial, 0, 1, buffer); 694 if (status) 695 goto out; 696 697 if (*buffer != UMP5152 && *buffer != UMP3410) { 698 dev_err(dev, "%s - invalid buffer signature\n", __func__); 699 status = -ENODEV; 700 goto out; 701 } 702 703 do { 704 /* Validate the I2C */ 705 status = read_rom(serial, 706 start_address, 707 sizeof(struct ti_i2c_desc), 708 (u8 *)rom_desc); 709 if (status) 710 break; 711 712 if ((start_address + sizeof(struct ti_i2c_desc) + 713 le16_to_cpu(rom_desc->Size)) > TI_MAX_I2C_SIZE) { 714 status = -ENODEV; 715 dev_dbg(dev, "%s - structure too big, erroring out.\n", __func__); 716 break; 717 } 718 719 dev_dbg(dev, "%s Type = 0x%x\n", __func__, rom_desc->Type); 720 721 /* Skip type 2 record */ 722 ttype = rom_desc->Type & 0x0f; 723 if (ttype != I2C_DESC_TYPE_FIRMWARE_BASIC 724 && ttype != I2C_DESC_TYPE_FIRMWARE_AUTO) { 725 /* Read the descriptor data */ 726 status = read_rom(serial, start_address + 727 sizeof(struct ti_i2c_desc), 728 le16_to_cpu(rom_desc->Size), 729 buffer); 730 if (status) 731 break; 732 733 status = valid_csum(rom_desc, buffer); 734 if (status) 735 break; 736 } 737 start_address = start_address + sizeof(struct ti_i2c_desc) + 738 le16_to_cpu(rom_desc->Size); 739 740 } while ((rom_desc->Type != I2C_DESC_TYPE_ION) && 741 (start_address < TI_MAX_I2C_SIZE)); 742 743 if ((rom_desc->Type != I2C_DESC_TYPE_ION) || 744 (start_address > TI_MAX_I2C_SIZE)) 745 status = -ENODEV; 746 747 out: 748 kfree(buffer); 749 kfree(rom_desc); 750 return status; 751 } 752 753 static int get_manuf_info(struct edgeport_serial *serial, u8 *buffer) 754 { 755 int status; 756 int start_address; 757 struct ti_i2c_desc *rom_desc; 758 struct edge_ti_manuf_descriptor *desc; 759 struct device *dev = &serial->serial->dev->dev; 760 761 rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); 762 if (!rom_desc) 763 return -ENOMEM; 764 765 start_address = get_descriptor_addr(serial, I2C_DESC_TYPE_ION, 766 rom_desc); 767 768 if (!start_address) { 769 dev_dbg(dev, "%s - Edge Descriptor not found in I2C\n", __func__); 770 status = -ENODEV; 771 goto exit; 772 } 773 774 /* Read the descriptor data */ 775 status = read_rom(serial, start_address+sizeof(struct ti_i2c_desc), 776 le16_to_cpu(rom_desc->Size), buffer); 777 if (status) 778 goto exit; 779 780 status = valid_csum(rom_desc, buffer); 781 782 desc = (struct edge_ti_manuf_descriptor *)buffer; 783 dev_dbg(dev, "%s - IonConfig 0x%x\n", __func__, desc->IonConfig); 784 dev_dbg(dev, "%s - Version %d\n", __func__, desc->Version); 785 dev_dbg(dev, "%s - Cpu/Board 0x%x\n", __func__, desc->CpuRev_BoardRev); 786 dev_dbg(dev, "%s - NumPorts %d\n", __func__, desc->NumPorts); 787 dev_dbg(dev, "%s - NumVirtualPorts %d\n", __func__, desc->NumVirtualPorts); 788 dev_dbg(dev, "%s - TotalPorts %d\n", __func__, desc->TotalPorts); 789 790 exit: 791 kfree(rom_desc); 792 return status; 793 } 794 795 /* Build firmware header used for firmware update */ 796 static int build_i2c_fw_hdr(u8 *header, const struct firmware *fw) 797 { 798 u8 *buffer; 799 int buffer_size; 800 int i; 801 u8 cs = 0; 802 struct ti_i2c_desc *i2c_header; 803 struct ti_i2c_image_header *img_header; 804 struct ti_i2c_firmware_rec *firmware_rec; 805 struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; 806 807 /* 808 * In order to update the I2C firmware we must change the type 2 record 809 * to type 0xF2. This will force the UMP to come up in Boot Mode. 810 * Then while in boot mode, the driver will download the latest 811 * firmware (padded to 15.5k) into the UMP ram. And finally when the 812 * device comes back up in download mode the driver will cause the new 813 * firmware to be copied from the UMP Ram to I2C and the firmware will 814 * update the record type from 0xf2 to 0x02. 815 */ 816 817 /* 818 * Allocate a 15.5k buffer + 2 bytes for version number (Firmware 819 * Record) 820 */ 821 buffer_size = (((1024 * 16) - 512 ) + 822 sizeof(struct ti_i2c_firmware_rec)); 823 824 buffer = kmalloc(buffer_size, GFP_KERNEL); 825 if (!buffer) 826 return -ENOMEM; 827 828 /* Set entire image of 0xffs */ 829 memset(buffer, 0xff, buffer_size); 830 831 /* Copy version number into firmware record */ 832 firmware_rec = (struct ti_i2c_firmware_rec *)buffer; 833 834 firmware_rec->Ver_Major = fw_hdr->major_version; 835 firmware_rec->Ver_Minor = fw_hdr->minor_version; 836 837 /* Pointer to fw_down memory image */ 838 img_header = (struct ti_i2c_image_header *)&fw->data[4]; 839 840 memcpy(buffer + sizeof(struct ti_i2c_firmware_rec), 841 &fw->data[4 + sizeof(struct ti_i2c_image_header)], 842 le16_to_cpu(img_header->Length)); 843 844 for (i=0; i < buffer_size; i++) { 845 cs = (u8)(cs + buffer[i]); 846 } 847 848 kfree(buffer); 849 850 /* Build new header */ 851 i2c_header = (struct ti_i2c_desc *)header; 852 firmware_rec = (struct ti_i2c_firmware_rec*)i2c_header->Data; 853 854 i2c_header->Type = I2C_DESC_TYPE_FIRMWARE_BLANK; 855 i2c_header->Size = cpu_to_le16(buffer_size); 856 i2c_header->CheckSum = cs; 857 firmware_rec->Ver_Major = fw_hdr->major_version; 858 firmware_rec->Ver_Minor = fw_hdr->minor_version; 859 860 return 0; 861 } 862 863 /* Try to figure out what type of I2c we have */ 864 static int i2c_type_bootmode(struct edgeport_serial *serial) 865 { 866 struct device *dev = &serial->serial->dev->dev; 867 int status; 868 u8 *data; 869 870 data = kmalloc(1, GFP_KERNEL); 871 if (!data) 872 return -ENOMEM; 873 874 /* Try to read type 2 */ 875 status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ, 876 DTK_ADDR_SPACE_I2C_TYPE_II, 0, data, 0x01); 877 if (status) 878 dev_dbg(dev, "%s - read 2 status error = %d\n", __func__, status); 879 else 880 dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data); 881 if ((!status) && (*data == UMP5152 || *data == UMP3410)) { 882 dev_dbg(dev, "%s - ROM_TYPE_II\n", __func__); 883 serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; 884 goto out; 885 } 886 887 /* Try to read type 3 */ 888 status = ti_vread_sync(serial->serial->dev, UMPC_MEMORY_READ, 889 DTK_ADDR_SPACE_I2C_TYPE_III, 0, data, 0x01); 890 if (status) 891 dev_dbg(dev, "%s - read 3 status error = %d\n", __func__, status); 892 else 893 dev_dbg(dev, "%s - read 2 data = 0x%x\n", __func__, *data); 894 if ((!status) && (*data == UMP5152 || *data == UMP3410)) { 895 dev_dbg(dev, "%s - ROM_TYPE_III\n", __func__); 896 serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_III; 897 goto out; 898 } 899 900 dev_dbg(dev, "%s - Unknown\n", __func__); 901 serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; 902 status = -ENODEV; 903 out: 904 kfree(data); 905 return status; 906 } 907 908 static int bulk_xfer(struct usb_serial *serial, void *buffer, 909 int length, int *num_sent) 910 { 911 int status; 912 913 status = usb_bulk_msg(serial->dev, 914 usb_sndbulkpipe(serial->dev, 915 serial->port[0]->bulk_out_endpointAddress), 916 buffer, length, num_sent, 1000); 917 return status; 918 } 919 920 /* Download given firmware image to the device (IN BOOT MODE) */ 921 static int download_code(struct edgeport_serial *serial, u8 *image, 922 int image_length) 923 { 924 int status = 0; 925 int pos; 926 int transfer; 927 int done; 928 929 /* Transfer firmware image */ 930 for (pos = 0; pos < image_length; ) { 931 /* Read the next buffer from file */ 932 transfer = image_length - pos; 933 if (transfer > EDGE_FW_BULK_MAX_PACKET_SIZE) 934 transfer = EDGE_FW_BULK_MAX_PACKET_SIZE; 935 936 /* Transfer data */ 937 status = bulk_xfer(serial->serial, &image[pos], 938 transfer, &done); 939 if (status) 940 break; 941 /* Advance buffer pointer */ 942 pos += done; 943 } 944 945 return status; 946 } 947 948 /* FIXME!!! */ 949 static int config_boot_dev(struct usb_device *dev) 950 { 951 return 0; 952 } 953 954 static int ti_cpu_rev(struct edge_ti_manuf_descriptor *desc) 955 { 956 return TI_GET_CPU_REVISION(desc->CpuRev_BoardRev); 957 } 958 959 static int check_fw_sanity(struct edgeport_serial *serial, 960 const struct firmware *fw) 961 { 962 u16 length_total; 963 u8 checksum = 0; 964 int pos; 965 struct device *dev = &serial->serial->interface->dev; 966 struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; 967 968 if (fw->size < sizeof(struct edgeport_fw_hdr)) { 969 dev_err(dev, "incomplete fw header\n"); 970 return -EINVAL; 971 } 972 973 length_total = le16_to_cpu(fw_hdr->length) + 974 sizeof(struct edgeport_fw_hdr); 975 976 if (fw->size != length_total) { 977 dev_err(dev, "bad fw size (expected: %u, got: %zu)\n", 978 length_total, fw->size); 979 return -EINVAL; 980 } 981 982 for (pos = sizeof(struct edgeport_fw_hdr); pos < fw->size; ++pos) 983 checksum += fw->data[pos]; 984 985 if (checksum != fw_hdr->checksum) { 986 dev_err(dev, "bad fw checksum (expected: 0x%x, got: 0x%x)\n", 987 fw_hdr->checksum, checksum); 988 return -EINVAL; 989 } 990 991 return 0; 992 } 993 994 /* 995 * DownloadTIFirmware - Download run-time operating firmware to the TI5052 996 * 997 * This routine downloads the main operating code into the TI5052, using the 998 * boot code already burned into E2PROM or ROM. 999 */ 1000 static int download_fw(struct edgeport_serial *serial) 1001 { 1002 struct device *dev = &serial->serial->interface->dev; 1003 int status = 0; 1004 struct usb_interface_descriptor *interface; 1005 const struct firmware *fw; 1006 const char *fw_name = "edgeport/down3.bin"; 1007 struct edgeport_fw_hdr *fw_hdr; 1008 1009 status = request_firmware(&fw, fw_name, dev); 1010 if (status) { 1011 dev_err(dev, "Failed to load image \"%s\" err %d\n", 1012 fw_name, status); 1013 return status; 1014 } 1015 1016 if (check_fw_sanity(serial, fw)) { 1017 status = -EINVAL; 1018 goto out; 1019 } 1020 1021 fw_hdr = (struct edgeport_fw_hdr *)fw->data; 1022 1023 /* If on-board version is newer, "fw_version" will be updated later. */ 1024 serial->fw_version = (fw_hdr->major_version << 8) + 1025 fw_hdr->minor_version; 1026 1027 /* 1028 * This routine is entered by both the BOOT mode and the Download mode 1029 * We can determine which code is running by the reading the config 1030 * descriptor and if we have only one bulk pipe it is in boot mode 1031 */ 1032 serial->product_info.hardware_type = HARDWARE_TYPE_TIUMP; 1033 1034 /* Default to type 2 i2c */ 1035 serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; 1036 1037 status = choose_config(serial->serial->dev); 1038 if (status) 1039 goto out; 1040 1041 interface = &serial->serial->interface->cur_altsetting->desc; 1042 if (!interface) { 1043 dev_err(dev, "%s - no interface set, error!\n", __func__); 1044 status = -ENODEV; 1045 goto out; 1046 } 1047 1048 /* 1049 * Setup initial mode -- the default mode 0 is TI_MODE_CONFIGURING 1050 * if we have more than one endpoint we are definitely in download 1051 * mode 1052 */ 1053 if (interface->bNumEndpoints > 1) { 1054 serial->product_info.TiMode = TI_MODE_DOWNLOAD; 1055 status = do_download_mode(serial, fw); 1056 } else { 1057 /* Otherwise we will remain in configuring mode */ 1058 serial->product_info.TiMode = TI_MODE_CONFIGURING; 1059 status = do_boot_mode(serial, fw); 1060 } 1061 1062 out: 1063 release_firmware(fw); 1064 return status; 1065 } 1066 1067 static int do_download_mode(struct edgeport_serial *serial, 1068 const struct firmware *fw) 1069 { 1070 struct device *dev = &serial->serial->interface->dev; 1071 int status = 0; 1072 int start_address; 1073 struct edge_ti_manuf_descriptor *ti_manuf_desc; 1074 int download_cur_ver; 1075 int download_new_ver; 1076 struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; 1077 struct ti_i2c_desc *rom_desc; 1078 1079 dev_dbg(dev, "%s - RUNNING IN DOWNLOAD MODE\n", __func__); 1080 1081 status = check_i2c_image(serial); 1082 if (status) { 1083 dev_dbg(dev, "%s - DOWNLOAD MODE -- BAD I2C\n", __func__); 1084 return status; 1085 } 1086 1087 /* 1088 * Validate Hardware version number 1089 * Read Manufacturing Descriptor from TI Based Edgeport 1090 */ 1091 ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL); 1092 if (!ti_manuf_desc) 1093 return -ENOMEM; 1094 1095 status = get_manuf_info(serial, (u8 *)ti_manuf_desc); 1096 if (status) { 1097 kfree(ti_manuf_desc); 1098 return status; 1099 } 1100 1101 /* Check version number of ION descriptor */ 1102 if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) { 1103 dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n", 1104 __func__, ti_cpu_rev(ti_manuf_desc)); 1105 kfree(ti_manuf_desc); 1106 return -EINVAL; 1107 } 1108 1109 rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); 1110 if (!rom_desc) { 1111 kfree(ti_manuf_desc); 1112 return -ENOMEM; 1113 } 1114 1115 /* Search for type 2 record (firmware record) */ 1116 start_address = get_descriptor_addr(serial, 1117 I2C_DESC_TYPE_FIRMWARE_BASIC, rom_desc); 1118 if (start_address != 0) { 1119 struct ti_i2c_firmware_rec *firmware_version; 1120 u8 *record; 1121 1122 dev_dbg(dev, "%s - Found Type FIRMWARE (Type 2) record\n", 1123 __func__); 1124 1125 firmware_version = kmalloc(sizeof(*firmware_version), 1126 GFP_KERNEL); 1127 if (!firmware_version) { 1128 kfree(rom_desc); 1129 kfree(ti_manuf_desc); 1130 return -ENOMEM; 1131 } 1132 1133 /* 1134 * Validate version number 1135 * Read the descriptor data 1136 */ 1137 status = read_rom(serial, start_address + 1138 sizeof(struct ti_i2c_desc), 1139 sizeof(struct ti_i2c_firmware_rec), 1140 (u8 *)firmware_version); 1141 if (status) { 1142 kfree(firmware_version); 1143 kfree(rom_desc); 1144 kfree(ti_manuf_desc); 1145 return status; 1146 } 1147 1148 /* 1149 * Check version number of download with current 1150 * version in I2c 1151 */ 1152 download_cur_ver = (firmware_version->Ver_Major << 8) + 1153 (firmware_version->Ver_Minor); 1154 download_new_ver = (fw_hdr->major_version << 8) + 1155 (fw_hdr->minor_version); 1156 1157 dev_dbg(dev, "%s - >> FW Versions Device %d.%d Driver %d.%d\n", 1158 __func__, firmware_version->Ver_Major, 1159 firmware_version->Ver_Minor, 1160 fw_hdr->major_version, fw_hdr->minor_version); 1161 1162 /* 1163 * Check if we have an old version in the I2C and 1164 * update if necessary 1165 */ 1166 if (download_cur_ver < download_new_ver) { 1167 dev_dbg(dev, "%s - Update I2C dld from %d.%d to %d.%d\n", 1168 __func__, 1169 firmware_version->Ver_Major, 1170 firmware_version->Ver_Minor, 1171 fw_hdr->major_version, 1172 fw_hdr->minor_version); 1173 1174 record = kmalloc(1, GFP_KERNEL); 1175 if (!record) { 1176 kfree(firmware_version); 1177 kfree(rom_desc); 1178 kfree(ti_manuf_desc); 1179 return -ENOMEM; 1180 } 1181 /* 1182 * In order to update the I2C firmware we must 1183 * change the type 2 record to type 0xF2. This 1184 * will force the UMP to come up in Boot Mode. 1185 * Then while in boot mode, the driver will 1186 * download the latest firmware (padded to 1187 * 15.5k) into the UMP ram. Finally when the 1188 * device comes back up in download mode the 1189 * driver will cause the new firmware to be 1190 * copied from the UMP Ram to I2C and the 1191 * firmware will update the record type from 1192 * 0xf2 to 0x02. 1193 */ 1194 *record = I2C_DESC_TYPE_FIRMWARE_BLANK; 1195 1196 /* 1197 * Change the I2C Firmware record type to 1198 * 0xf2 to trigger an update 1199 */ 1200 status = write_rom(serial, start_address, 1201 sizeof(*record), record); 1202 if (status) { 1203 kfree(record); 1204 kfree(firmware_version); 1205 kfree(rom_desc); 1206 kfree(ti_manuf_desc); 1207 return status; 1208 } 1209 1210 /* 1211 * verify the write -- must do this in order 1212 * for write to complete before we do the 1213 * hardware reset 1214 */ 1215 status = read_rom(serial, 1216 start_address, 1217 sizeof(*record), 1218 record); 1219 if (status) { 1220 kfree(record); 1221 kfree(firmware_version); 1222 kfree(rom_desc); 1223 kfree(ti_manuf_desc); 1224 return status; 1225 } 1226 1227 if (*record != I2C_DESC_TYPE_FIRMWARE_BLANK) { 1228 dev_err(dev, "%s - error resetting device\n", 1229 __func__); 1230 kfree(record); 1231 kfree(firmware_version); 1232 kfree(rom_desc); 1233 kfree(ti_manuf_desc); 1234 return -ENODEV; 1235 } 1236 1237 dev_dbg(dev, "%s - HARDWARE RESET\n", __func__); 1238 1239 /* Reset UMP -- Back to BOOT MODE */ 1240 status = ti_vsend_sync(serial->serial->dev, 1241 UMPC_HARDWARE_RESET, 1242 0, 0, NULL, 0, 1243 TI_VSEND_TIMEOUT_DEFAULT); 1244 1245 dev_dbg(dev, "%s - HARDWARE RESET return %d\n", 1246 __func__, status); 1247 1248 /* return an error on purpose. */ 1249 kfree(record); 1250 kfree(firmware_version); 1251 kfree(rom_desc); 1252 kfree(ti_manuf_desc); 1253 return -ENODEV; 1254 } 1255 /* Same or newer fw version is already loaded */ 1256 serial->fw_version = download_cur_ver; 1257 kfree(firmware_version); 1258 } 1259 /* Search for type 0xF2 record (firmware blank record) */ 1260 else { 1261 start_address = get_descriptor_addr(serial, 1262 I2C_DESC_TYPE_FIRMWARE_BLANK, rom_desc); 1263 if (start_address != 0) { 1264 #define HEADER_SIZE (sizeof(struct ti_i2c_desc) + \ 1265 sizeof(struct ti_i2c_firmware_rec)) 1266 u8 *header; 1267 u8 *vheader; 1268 1269 header = kmalloc(HEADER_SIZE, GFP_KERNEL); 1270 if (!header) { 1271 kfree(rom_desc); 1272 kfree(ti_manuf_desc); 1273 return -ENOMEM; 1274 } 1275 1276 vheader = kmalloc(HEADER_SIZE, GFP_KERNEL); 1277 if (!vheader) { 1278 kfree(header); 1279 kfree(rom_desc); 1280 kfree(ti_manuf_desc); 1281 return -ENOMEM; 1282 } 1283 1284 dev_dbg(dev, "%s - Found Type BLANK FIRMWARE (Type F2) record\n", 1285 __func__); 1286 1287 /* 1288 * In order to update the I2C firmware we must change 1289 * the type 2 record to type 0xF2. This will force the 1290 * UMP to come up in Boot Mode. Then while in boot 1291 * mode, the driver will download the latest firmware 1292 * (padded to 15.5k) into the UMP ram. Finally when the 1293 * device comes back up in download mode the driver 1294 * will cause the new firmware to be copied from the 1295 * UMP Ram to I2C and the firmware will update the 1296 * record type from 0xf2 to 0x02. 1297 */ 1298 status = build_i2c_fw_hdr(header, fw); 1299 if (status) { 1300 kfree(vheader); 1301 kfree(header); 1302 kfree(rom_desc); 1303 kfree(ti_manuf_desc); 1304 return -EINVAL; 1305 } 1306 1307 /* 1308 * Update I2C with type 0xf2 record with correct 1309 * size and checksum 1310 */ 1311 status = write_rom(serial, 1312 start_address, 1313 HEADER_SIZE, 1314 header); 1315 if (status) { 1316 kfree(vheader); 1317 kfree(header); 1318 kfree(rom_desc); 1319 kfree(ti_manuf_desc); 1320 return -EINVAL; 1321 } 1322 1323 /* 1324 * verify the write -- must do this in order for 1325 * write to complete before we do the hardware reset 1326 */ 1327 status = read_rom(serial, start_address, 1328 HEADER_SIZE, vheader); 1329 1330 if (status) { 1331 dev_dbg(dev, "%s - can't read header back\n", 1332 __func__); 1333 kfree(vheader); 1334 kfree(header); 1335 kfree(rom_desc); 1336 kfree(ti_manuf_desc); 1337 return status; 1338 } 1339 if (memcmp(vheader, header, HEADER_SIZE)) { 1340 dev_dbg(dev, "%s - write download record failed\n", 1341 __func__); 1342 kfree(vheader); 1343 kfree(header); 1344 kfree(rom_desc); 1345 kfree(ti_manuf_desc); 1346 return -EINVAL; 1347 } 1348 1349 kfree(vheader); 1350 kfree(header); 1351 1352 dev_dbg(dev, "%s - Start firmware update\n", __func__); 1353 1354 /* Tell firmware to copy download image into I2C */ 1355 status = ti_vsend_sync(serial->serial->dev, 1356 UMPC_COPY_DNLD_TO_I2C, 1357 0, 0, NULL, 0, 1358 TI_VSEND_TIMEOUT_FW_DOWNLOAD); 1359 1360 dev_dbg(dev, "%s - Update complete 0x%x\n", __func__, 1361 status); 1362 if (status) { 1363 dev_err(dev, 1364 "%s - UMPC_COPY_DNLD_TO_I2C failed\n", 1365 __func__); 1366 kfree(rom_desc); 1367 kfree(ti_manuf_desc); 1368 return status; 1369 } 1370 } 1371 } 1372 1373 /* The device is running the download code */ 1374 kfree(rom_desc); 1375 kfree(ti_manuf_desc); 1376 return 0; 1377 } 1378 1379 static int do_boot_mode(struct edgeport_serial *serial, 1380 const struct firmware *fw) 1381 { 1382 struct device *dev = &serial->serial->interface->dev; 1383 int status = 0; 1384 struct edge_ti_manuf_descriptor *ti_manuf_desc; 1385 struct edgeport_fw_hdr *fw_hdr = (struct edgeport_fw_hdr *)fw->data; 1386 1387 dev_dbg(dev, "%s - RUNNING IN BOOT MODE\n", __func__); 1388 1389 /* Configure the TI device so we can use the BULK pipes for download */ 1390 status = config_boot_dev(serial->serial->dev); 1391 if (status) 1392 return status; 1393 1394 if (le16_to_cpu(serial->serial->dev->descriptor.idVendor) 1395 != USB_VENDOR_ID_ION) { 1396 dev_dbg(dev, "%s - VID = 0x%x\n", __func__, 1397 le16_to_cpu(serial->serial->dev->descriptor.idVendor)); 1398 serial->TI_I2C_Type = DTK_ADDR_SPACE_I2C_TYPE_II; 1399 goto stayinbootmode; 1400 } 1401 1402 /* 1403 * We have an ION device (I2c Must be programmed) 1404 * Determine I2C image type 1405 */ 1406 if (i2c_type_bootmode(serial)) 1407 goto stayinbootmode; 1408 1409 /* Check for ION Vendor ID and that the I2C is valid */ 1410 if (!check_i2c_image(serial)) { 1411 struct ti_i2c_image_header *header; 1412 int i; 1413 u8 cs = 0; 1414 u8 *buffer; 1415 int buffer_size; 1416 1417 /* 1418 * Validate Hardware version number 1419 * Read Manufacturing Descriptor from TI Based Edgeport 1420 */ 1421 ti_manuf_desc = kmalloc(sizeof(*ti_manuf_desc), GFP_KERNEL); 1422 if (!ti_manuf_desc) 1423 return -ENOMEM; 1424 1425 status = get_manuf_info(serial, (u8 *)ti_manuf_desc); 1426 if (status) { 1427 kfree(ti_manuf_desc); 1428 goto stayinbootmode; 1429 } 1430 1431 /* Check for version 2 */ 1432 if (!ignore_cpu_rev && ti_cpu_rev(ti_manuf_desc) < 2) { 1433 dev_dbg(dev, "%s - Wrong CPU Rev %d (Must be 2)\n", 1434 __func__, ti_cpu_rev(ti_manuf_desc)); 1435 kfree(ti_manuf_desc); 1436 goto stayinbootmode; 1437 } 1438 1439 kfree(ti_manuf_desc); 1440 1441 /* 1442 * In order to update the I2C firmware we must change the type 1443 * 2 record to type 0xF2. This will force the UMP to come up 1444 * in Boot Mode. Then while in boot mode, the driver will 1445 * download the latest firmware (padded to 15.5k) into the 1446 * UMP ram. Finally when the device comes back up in download 1447 * mode the driver will cause the new firmware to be copied 1448 * from the UMP Ram to I2C and the firmware will update the 1449 * record type from 0xf2 to 0x02. 1450 * 1451 * Do we really have to copy the whole firmware image, 1452 * or could we do this in place! 1453 */ 1454 1455 /* Allocate a 15.5k buffer + 3 byte header */ 1456 buffer_size = (((1024 * 16) - 512) + 1457 sizeof(struct ti_i2c_image_header)); 1458 buffer = kmalloc(buffer_size, GFP_KERNEL); 1459 if (!buffer) 1460 return -ENOMEM; 1461 1462 /* Initialize the buffer to 0xff (pad the buffer) */ 1463 memset(buffer, 0xff, buffer_size); 1464 memcpy(buffer, &fw->data[4], fw->size - 4); 1465 1466 for (i = sizeof(struct ti_i2c_image_header); 1467 i < buffer_size; i++) { 1468 cs = (u8)(cs + buffer[i]); 1469 } 1470 1471 header = (struct ti_i2c_image_header *)buffer; 1472 1473 /* update length and checksum after padding */ 1474 header->Length = cpu_to_le16((u16)(buffer_size - 1475 sizeof(struct ti_i2c_image_header))); 1476 header->CheckSum = cs; 1477 1478 /* Download the operational code */ 1479 dev_dbg(dev, "%s - Downloading operational code image version %d.%d (TI UMP)\n", 1480 __func__, 1481 fw_hdr->major_version, fw_hdr->minor_version); 1482 status = download_code(serial, buffer, buffer_size); 1483 1484 kfree(buffer); 1485 1486 if (status) { 1487 dev_dbg(dev, "%s - Error downloading operational code image\n", __func__); 1488 return status; 1489 } 1490 1491 /* Device will reboot */ 1492 serial->product_info.TiMode = TI_MODE_TRANSITIONING; 1493 1494 dev_dbg(dev, "%s - Download successful -- Device rebooting...\n", __func__); 1495 1496 return 1; 1497 } 1498 1499 stayinbootmode: 1500 /* Eprom is invalid or blank stay in boot mode */ 1501 dev_dbg(dev, "%s - STAYING IN BOOT MODE\n", __func__); 1502 serial->product_info.TiMode = TI_MODE_BOOT; 1503 1504 return 1; 1505 } 1506 1507 static int ti_do_config(struct edgeport_port *port, int feature, int on) 1508 { 1509 on = !!on; /* 1 or 0 not bitmask */ 1510 1511 return send_port_cmd(port->port, feature, on, NULL, 0); 1512 } 1513 1514 static int restore_mcr(struct edgeport_port *port, u8 mcr) 1515 { 1516 int status = 0; 1517 1518 dev_dbg(&port->port->dev, "%s - %x\n", __func__, mcr); 1519 1520 status = ti_do_config(port, UMPC_SET_CLR_DTR, mcr & MCR_DTR); 1521 if (status) 1522 return status; 1523 status = ti_do_config(port, UMPC_SET_CLR_RTS, mcr & MCR_RTS); 1524 if (status) 1525 return status; 1526 return ti_do_config(port, UMPC_SET_CLR_LOOPBACK, mcr & MCR_LOOPBACK); 1527 } 1528 1529 /* Convert TI LSR to standard UART flags */ 1530 static u8 map_line_status(u8 ti_lsr) 1531 { 1532 u8 lsr = 0; 1533 1534 #define MAP_FLAG(flagUmp, flagUart) \ 1535 if (ti_lsr & flagUmp) \ 1536 lsr |= flagUart; 1537 1538 MAP_FLAG(UMP_UART_LSR_OV_MASK, LSR_OVER_ERR) /* overrun */ 1539 MAP_FLAG(UMP_UART_LSR_PE_MASK, LSR_PAR_ERR) /* parity error */ 1540 MAP_FLAG(UMP_UART_LSR_FE_MASK, LSR_FRM_ERR) /* framing error */ 1541 MAP_FLAG(UMP_UART_LSR_BR_MASK, LSR_BREAK) /* break detected */ 1542 MAP_FLAG(UMP_UART_LSR_RX_MASK, LSR_RX_AVAIL) /* rx data available */ 1543 MAP_FLAG(UMP_UART_LSR_TX_MASK, LSR_TX_EMPTY) /* tx hold reg empty */ 1544 1545 #undef MAP_FLAG 1546 1547 return lsr; 1548 } 1549 1550 static void handle_new_msr(struct edgeport_port *edge_port, u8 msr) 1551 { 1552 struct async_icount *icount; 1553 struct tty_struct *tty; 1554 1555 dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, msr); 1556 1557 if (msr & (EDGEPORT_MSR_DELTA_CTS | EDGEPORT_MSR_DELTA_DSR | 1558 EDGEPORT_MSR_DELTA_RI | EDGEPORT_MSR_DELTA_CD)) { 1559 icount = &edge_port->port->icount; 1560 1561 /* update input line counters */ 1562 if (msr & EDGEPORT_MSR_DELTA_CTS) 1563 icount->cts++; 1564 if (msr & EDGEPORT_MSR_DELTA_DSR) 1565 icount->dsr++; 1566 if (msr & EDGEPORT_MSR_DELTA_CD) 1567 icount->dcd++; 1568 if (msr & EDGEPORT_MSR_DELTA_RI) 1569 icount->rng++; 1570 wake_up_interruptible(&edge_port->port->port.delta_msr_wait); 1571 } 1572 1573 /* Save the new modem status */ 1574 edge_port->shadow_msr = msr & 0xf0; 1575 1576 tty = tty_port_tty_get(&edge_port->port->port); 1577 /* handle CTS flow control */ 1578 if (tty && C_CRTSCTS(tty)) { 1579 if (msr & EDGEPORT_MSR_CTS) 1580 tty_wakeup(tty); 1581 } 1582 tty_kref_put(tty); 1583 } 1584 1585 static void handle_new_lsr(struct edgeport_port *edge_port, int lsr_data, 1586 u8 lsr, u8 data) 1587 { 1588 struct async_icount *icount; 1589 u8 new_lsr = (u8)(lsr & (u8)(LSR_OVER_ERR | LSR_PAR_ERR | 1590 LSR_FRM_ERR | LSR_BREAK)); 1591 1592 dev_dbg(&edge_port->port->dev, "%s - %02x\n", __func__, new_lsr); 1593 1594 edge_port->shadow_lsr = lsr; 1595 1596 if (new_lsr & LSR_BREAK) 1597 /* 1598 * Parity and Framing errors only count if they 1599 * occur exclusive of a break being received. 1600 */ 1601 new_lsr &= (u8)(LSR_OVER_ERR | LSR_BREAK); 1602 1603 /* Place LSR data byte into Rx buffer */ 1604 if (lsr_data) 1605 edge_tty_recv(edge_port->port, &data, 1); 1606 1607 /* update input line counters */ 1608 icount = &edge_port->port->icount; 1609 if (new_lsr & LSR_BREAK) 1610 icount->brk++; 1611 if (new_lsr & LSR_OVER_ERR) 1612 icount->overrun++; 1613 if (new_lsr & LSR_PAR_ERR) 1614 icount->parity++; 1615 if (new_lsr & LSR_FRM_ERR) 1616 icount->frame++; 1617 } 1618 1619 static void edge_interrupt_callback(struct urb *urb) 1620 { 1621 struct edgeport_serial *edge_serial = urb->context; 1622 struct usb_serial_port *port; 1623 struct edgeport_port *edge_port; 1624 struct device *dev; 1625 unsigned char *data = urb->transfer_buffer; 1626 int length = urb->actual_length; 1627 int port_number; 1628 int function; 1629 int retval; 1630 u8 lsr; 1631 u8 msr; 1632 int status = urb->status; 1633 1634 switch (status) { 1635 case 0: 1636 /* success */ 1637 break; 1638 case -ECONNRESET: 1639 case -ENOENT: 1640 case -ESHUTDOWN: 1641 /* this urb is terminated, clean up */ 1642 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", 1643 __func__, status); 1644 return; 1645 default: 1646 dev_err(&urb->dev->dev, "%s - nonzero urb status received: " 1647 "%d\n", __func__, status); 1648 goto exit; 1649 } 1650 1651 if (!length) { 1652 dev_dbg(&urb->dev->dev, "%s - no data in urb\n", __func__); 1653 goto exit; 1654 } 1655 1656 dev = &edge_serial->serial->dev->dev; 1657 usb_serial_debug_data(dev, __func__, length, data); 1658 1659 if (length != 2) { 1660 dev_dbg(dev, "%s - expecting packet of size 2, got %d\n", __func__, length); 1661 goto exit; 1662 } 1663 1664 port_number = TIUMP_GET_PORT_FROM_CODE(data[0]); 1665 function = TIUMP_GET_FUNC_FROM_CODE(data[0]); 1666 dev_dbg(dev, "%s - port_number %d, function %d, info 0x%x\n", __func__, 1667 port_number, function, data[1]); 1668 1669 if (port_number >= edge_serial->serial->num_ports) { 1670 dev_err(dev, "bad port number %d\n", port_number); 1671 goto exit; 1672 } 1673 1674 port = edge_serial->serial->port[port_number]; 1675 edge_port = usb_get_serial_port_data(port); 1676 if (!edge_port) { 1677 dev_dbg(dev, "%s - edge_port not found\n", __func__); 1678 return; 1679 } 1680 switch (function) { 1681 case TIUMP_INTERRUPT_CODE_LSR: 1682 lsr = map_line_status(data[1]); 1683 if (lsr & UMP_UART_LSR_DATA_MASK) { 1684 /* 1685 * Save the LSR event for bulk read completion routine 1686 */ 1687 dev_dbg(dev, "%s - LSR Event Port %u LSR Status = %02x\n", 1688 __func__, port_number, lsr); 1689 edge_port->lsr_event = 1; 1690 edge_port->lsr_mask = lsr; 1691 } else { 1692 dev_dbg(dev, "%s - ===== Port %d LSR Status = %02x ======\n", 1693 __func__, port_number, lsr); 1694 handle_new_lsr(edge_port, 0, lsr, 0); 1695 } 1696 break; 1697 1698 case TIUMP_INTERRUPT_CODE_MSR: /* MSR */ 1699 /* Copy MSR from UMP */ 1700 msr = data[1]; 1701 dev_dbg(dev, "%s - ===== Port %u MSR Status = %02x ======\n", 1702 __func__, port_number, msr); 1703 handle_new_msr(edge_port, msr); 1704 break; 1705 1706 default: 1707 dev_err(&urb->dev->dev, 1708 "%s - Unknown Interrupt code from UMP %x\n", 1709 __func__, data[1]); 1710 break; 1711 1712 } 1713 1714 exit: 1715 retval = usb_submit_urb(urb, GFP_ATOMIC); 1716 if (retval) 1717 dev_err(&urb->dev->dev, 1718 "%s - usb_submit_urb failed with result %d\n", 1719 __func__, retval); 1720 } 1721 1722 static void edge_bulk_in_callback(struct urb *urb) 1723 { 1724 struct edgeport_port *edge_port = urb->context; 1725 struct device *dev = &edge_port->port->dev; 1726 unsigned char *data = urb->transfer_buffer; 1727 unsigned long flags; 1728 int retval = 0; 1729 int port_number; 1730 int status = urb->status; 1731 1732 switch (status) { 1733 case 0: 1734 /* success */ 1735 break; 1736 case -ECONNRESET: 1737 case -ENOENT: 1738 case -ESHUTDOWN: 1739 /* this urb is terminated, clean up */ 1740 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", __func__, status); 1741 return; 1742 default: 1743 dev_err(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n", __func__, status); 1744 } 1745 1746 if (status == -EPIPE) 1747 goto exit; 1748 1749 if (status) { 1750 dev_err(&urb->dev->dev, "%s - stopping read!\n", __func__); 1751 return; 1752 } 1753 1754 port_number = edge_port->port->port_number; 1755 1756 if (urb->actual_length > 0 && edge_port->lsr_event) { 1757 edge_port->lsr_event = 0; 1758 dev_dbg(dev, "%s ===== Port %u LSR Status = %02x, Data = %02x ======\n", 1759 __func__, port_number, edge_port->lsr_mask, *data); 1760 handle_new_lsr(edge_port, 1, edge_port->lsr_mask, *data); 1761 /* Adjust buffer length/pointer */ 1762 --urb->actual_length; 1763 ++data; 1764 } 1765 1766 if (urb->actual_length) { 1767 usb_serial_debug_data(dev, __func__, urb->actual_length, data); 1768 if (edge_port->close_pending) 1769 dev_dbg(dev, "%s - close pending, dropping data on the floor\n", 1770 __func__); 1771 else 1772 edge_tty_recv(edge_port->port, data, 1773 urb->actual_length); 1774 edge_port->port->icount.rx += urb->actual_length; 1775 } 1776 1777 exit: 1778 /* continue read unless stopped */ 1779 spin_lock_irqsave(&edge_port->ep_lock, flags); 1780 if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING) 1781 retval = usb_submit_urb(urb, GFP_ATOMIC); 1782 else if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPING) 1783 edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPED; 1784 1785 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 1786 if (retval) 1787 dev_err(dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval); 1788 } 1789 1790 static void edge_tty_recv(struct usb_serial_port *port, unsigned char *data, 1791 int length) 1792 { 1793 int queued; 1794 1795 queued = tty_insert_flip_string(&port->port, data, length); 1796 if (queued < length) 1797 dev_err(&port->dev, "%s - dropping data, %d bytes lost\n", 1798 __func__, length - queued); 1799 tty_flip_buffer_push(&port->port); 1800 } 1801 1802 static void edge_bulk_out_callback(struct urb *urb) 1803 { 1804 struct usb_serial_port *port = urb->context; 1805 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 1806 int status = urb->status; 1807 struct tty_struct *tty; 1808 1809 edge_port->ep_write_urb_in_use = 0; 1810 1811 switch (status) { 1812 case 0: 1813 /* success */ 1814 break; 1815 case -ECONNRESET: 1816 case -ENOENT: 1817 case -ESHUTDOWN: 1818 /* this urb is terminated, clean up */ 1819 dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n", 1820 __func__, status); 1821 return; 1822 default: 1823 dev_err_console(port, "%s - nonzero write bulk status " 1824 "received: %d\n", __func__, status); 1825 } 1826 1827 /* send any buffered data */ 1828 tty = tty_port_tty_get(&port->port); 1829 edge_send(port, tty); 1830 tty_kref_put(tty); 1831 } 1832 1833 static int edge_open(struct tty_struct *tty, struct usb_serial_port *port) 1834 { 1835 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 1836 struct edgeport_serial *edge_serial; 1837 struct usb_device *dev; 1838 struct urb *urb; 1839 int status; 1840 u16 open_settings; 1841 u8 transaction_timeout; 1842 1843 if (edge_port == NULL) 1844 return -ENODEV; 1845 1846 dev = port->serial->dev; 1847 1848 /* turn off loopback */ 1849 status = ti_do_config(edge_port, UMPC_SET_CLR_LOOPBACK, 0); 1850 if (status) { 1851 dev_err(&port->dev, 1852 "%s - cannot send clear loopback command, %d\n", 1853 __func__, status); 1854 return status; 1855 } 1856 1857 /* set up the port settings */ 1858 if (tty) 1859 edge_set_termios(tty, port, &tty->termios); 1860 1861 /* open up the port */ 1862 1863 /* milliseconds to timeout for DMA transfer */ 1864 transaction_timeout = 2; 1865 1866 edge_port->ump_read_timeout = 1867 max(20, ((transaction_timeout * 3) / 2)); 1868 1869 /* milliseconds to timeout for DMA transfer */ 1870 open_settings = (u8)(UMP_DMA_MODE_CONTINOUS | 1871 UMP_PIPE_TRANS_TIMEOUT_ENA | 1872 (transaction_timeout << 2)); 1873 1874 dev_dbg(&port->dev, "%s - Sending UMPC_OPEN_PORT\n", __func__); 1875 1876 /* Tell TI to open and start the port */ 1877 status = send_port_cmd(port, UMPC_OPEN_PORT, open_settings, NULL, 0); 1878 if (status) { 1879 dev_err(&port->dev, "%s - cannot send open command, %d\n", 1880 __func__, status); 1881 return status; 1882 } 1883 1884 /* Start the DMA? */ 1885 status = send_port_cmd(port, UMPC_START_PORT, 0, NULL, 0); 1886 if (status) { 1887 dev_err(&port->dev, "%s - cannot send start DMA command, %d\n", 1888 __func__, status); 1889 return status; 1890 } 1891 1892 /* Clear TX and RX buffers in UMP */ 1893 status = purge_port(port, UMP_PORT_DIR_OUT | UMP_PORT_DIR_IN); 1894 if (status) { 1895 dev_err(&port->dev, 1896 "%s - cannot send clear buffers command, %d\n", 1897 __func__, status); 1898 return status; 1899 } 1900 1901 /* Read Initial MSR */ 1902 status = read_port_cmd(port, UMPC_READ_MSR, 0, &edge_port->shadow_msr, 1); 1903 if (status) { 1904 dev_err(&port->dev, "%s - cannot send read MSR command, %d\n", 1905 __func__, status); 1906 return status; 1907 } 1908 1909 dev_dbg(&port->dev, "ShadowMSR 0x%X\n", edge_port->shadow_msr); 1910 1911 /* Set Initial MCR */ 1912 edge_port->shadow_mcr = MCR_RTS | MCR_DTR; 1913 dev_dbg(&port->dev, "ShadowMCR 0x%X\n", edge_port->shadow_mcr); 1914 1915 edge_serial = edge_port->edge_serial; 1916 if (mutex_lock_interruptible(&edge_serial->es_lock)) 1917 return -ERESTARTSYS; 1918 if (edge_serial->num_ports_open == 0) { 1919 /* we are the first port to open, post the interrupt urb */ 1920 urb = edge_serial->serial->port[0]->interrupt_in_urb; 1921 urb->context = edge_serial; 1922 status = usb_submit_urb(urb, GFP_KERNEL); 1923 if (status) { 1924 dev_err(&port->dev, 1925 "%s - usb_submit_urb failed with value %d\n", 1926 __func__, status); 1927 goto release_es_lock; 1928 } 1929 } 1930 1931 /* 1932 * reset the data toggle on the bulk endpoints to work around bug in 1933 * host controllers where things get out of sync some times 1934 */ 1935 usb_clear_halt(dev, port->write_urb->pipe); 1936 usb_clear_halt(dev, port->read_urb->pipe); 1937 1938 /* start up our bulk read urb */ 1939 urb = port->read_urb; 1940 edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING; 1941 urb->context = edge_port; 1942 status = usb_submit_urb(urb, GFP_KERNEL); 1943 if (status) { 1944 dev_err(&port->dev, 1945 "%s - read bulk usb_submit_urb failed with value %d\n", 1946 __func__, status); 1947 goto unlink_int_urb; 1948 } 1949 1950 ++edge_serial->num_ports_open; 1951 1952 goto release_es_lock; 1953 1954 unlink_int_urb: 1955 if (edge_port->edge_serial->num_ports_open == 0) 1956 usb_kill_urb(port->serial->port[0]->interrupt_in_urb); 1957 release_es_lock: 1958 mutex_unlock(&edge_serial->es_lock); 1959 return status; 1960 } 1961 1962 static void edge_close(struct usb_serial_port *port) 1963 { 1964 struct edgeport_serial *edge_serial; 1965 struct edgeport_port *edge_port; 1966 unsigned long flags; 1967 1968 edge_serial = usb_get_serial_data(port->serial); 1969 edge_port = usb_get_serial_port_data(port); 1970 if (edge_serial == NULL || edge_port == NULL) 1971 return; 1972 1973 /* 1974 * The bulkreadcompletion routine will check 1975 * this flag and dump add read data 1976 */ 1977 edge_port->close_pending = 1; 1978 1979 usb_kill_urb(port->read_urb); 1980 usb_kill_urb(port->write_urb); 1981 edge_port->ep_write_urb_in_use = 0; 1982 spin_lock_irqsave(&edge_port->ep_lock, flags); 1983 kfifo_reset_out(&port->write_fifo); 1984 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 1985 1986 dev_dbg(&port->dev, "%s - send umpc_close_port\n", __func__); 1987 send_port_cmd(port, UMPC_CLOSE_PORT, 0, NULL, 0); 1988 1989 mutex_lock(&edge_serial->es_lock); 1990 --edge_port->edge_serial->num_ports_open; 1991 if (edge_port->edge_serial->num_ports_open <= 0) { 1992 /* last port is now closed, let's shut down our interrupt urb */ 1993 usb_kill_urb(port->serial->port[0]->interrupt_in_urb); 1994 edge_port->edge_serial->num_ports_open = 0; 1995 } 1996 mutex_unlock(&edge_serial->es_lock); 1997 edge_port->close_pending = 0; 1998 } 1999 2000 static int edge_write(struct tty_struct *tty, struct usb_serial_port *port, 2001 const unsigned char *data, int count) 2002 { 2003 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2004 2005 if (count == 0) { 2006 dev_dbg(&port->dev, "%s - write request of 0 bytes\n", __func__); 2007 return 0; 2008 } 2009 2010 if (edge_port == NULL) 2011 return -ENODEV; 2012 if (edge_port->close_pending == 1) 2013 return -ENODEV; 2014 2015 count = kfifo_in_locked(&port->write_fifo, data, count, 2016 &edge_port->ep_lock); 2017 edge_send(port, tty); 2018 2019 return count; 2020 } 2021 2022 static void edge_send(struct usb_serial_port *port, struct tty_struct *tty) 2023 { 2024 int count, result; 2025 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2026 unsigned long flags; 2027 2028 spin_lock_irqsave(&edge_port->ep_lock, flags); 2029 2030 if (edge_port->ep_write_urb_in_use) { 2031 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2032 return; 2033 } 2034 2035 count = kfifo_out(&port->write_fifo, 2036 port->write_urb->transfer_buffer, 2037 port->bulk_out_size); 2038 2039 if (count == 0) { 2040 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2041 return; 2042 } 2043 2044 edge_port->ep_write_urb_in_use = 1; 2045 2046 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2047 2048 usb_serial_debug_data(&port->dev, __func__, count, port->write_urb->transfer_buffer); 2049 2050 /* set up our urb */ 2051 port->write_urb->transfer_buffer_length = count; 2052 2053 /* send the data out the bulk port */ 2054 result = usb_submit_urb(port->write_urb, GFP_ATOMIC); 2055 if (result) { 2056 dev_err_console(port, 2057 "%s - failed submitting write urb, error %d\n", 2058 __func__, result); 2059 edge_port->ep_write_urb_in_use = 0; 2060 /* TODO: reschedule edge_send */ 2061 } else 2062 edge_port->port->icount.tx += count; 2063 2064 /* 2065 * wakeup any process waiting for writes to complete 2066 * there is now more room in the buffer for new writes 2067 */ 2068 if (tty) 2069 tty_wakeup(tty); 2070 } 2071 2072 static unsigned int edge_write_room(struct tty_struct *tty) 2073 { 2074 struct usb_serial_port *port = tty->driver_data; 2075 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2076 unsigned int room; 2077 unsigned long flags; 2078 2079 if (edge_port == NULL) 2080 return 0; 2081 if (edge_port->close_pending == 1) 2082 return 0; 2083 2084 spin_lock_irqsave(&edge_port->ep_lock, flags); 2085 room = kfifo_avail(&port->write_fifo); 2086 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2087 2088 dev_dbg(&port->dev, "%s - returns %u\n", __func__, room); 2089 return room; 2090 } 2091 2092 static unsigned int edge_chars_in_buffer(struct tty_struct *tty) 2093 { 2094 struct usb_serial_port *port = tty->driver_data; 2095 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2096 unsigned int chars; 2097 unsigned long flags; 2098 if (edge_port == NULL) 2099 return 0; 2100 2101 spin_lock_irqsave(&edge_port->ep_lock, flags); 2102 chars = kfifo_len(&port->write_fifo); 2103 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2104 2105 dev_dbg(&port->dev, "%s - returns %u\n", __func__, chars); 2106 return chars; 2107 } 2108 2109 static bool edge_tx_empty(struct usb_serial_port *port) 2110 { 2111 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2112 int ret; 2113 2114 ret = tx_active(edge_port); 2115 if (ret > 0) 2116 return false; 2117 2118 return true; 2119 } 2120 2121 static void edge_throttle(struct tty_struct *tty) 2122 { 2123 struct usb_serial_port *port = tty->driver_data; 2124 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2125 int status; 2126 2127 if (edge_port == NULL) 2128 return; 2129 2130 /* if we are implementing XON/XOFF, send the stop character */ 2131 if (I_IXOFF(tty)) { 2132 unsigned char stop_char = STOP_CHAR(tty); 2133 status = edge_write(tty, port, &stop_char, 1); 2134 if (status <= 0) { 2135 dev_err(&port->dev, "%s - failed to write stop character, %d\n", __func__, status); 2136 } 2137 } 2138 2139 /* 2140 * if we are implementing RTS/CTS, stop reads 2141 * and the Edgeport will clear the RTS line 2142 */ 2143 if (C_CRTSCTS(tty)) 2144 stop_read(edge_port); 2145 2146 } 2147 2148 static void edge_unthrottle(struct tty_struct *tty) 2149 { 2150 struct usb_serial_port *port = tty->driver_data; 2151 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2152 int status; 2153 2154 if (edge_port == NULL) 2155 return; 2156 2157 /* if we are implementing XON/XOFF, send the start character */ 2158 if (I_IXOFF(tty)) { 2159 unsigned char start_char = START_CHAR(tty); 2160 status = edge_write(tty, port, &start_char, 1); 2161 if (status <= 0) { 2162 dev_err(&port->dev, "%s - failed to write start character, %d\n", __func__, status); 2163 } 2164 } 2165 /* 2166 * if we are implementing RTS/CTS, restart reads 2167 * are the Edgeport will assert the RTS line 2168 */ 2169 if (C_CRTSCTS(tty)) { 2170 status = restart_read(edge_port); 2171 if (status) 2172 dev_err(&port->dev, 2173 "%s - read bulk usb_submit_urb failed: %d\n", 2174 __func__, status); 2175 } 2176 2177 } 2178 2179 static void stop_read(struct edgeport_port *edge_port) 2180 { 2181 unsigned long flags; 2182 2183 spin_lock_irqsave(&edge_port->ep_lock, flags); 2184 2185 if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING) 2186 edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPING; 2187 edge_port->shadow_mcr &= ~MCR_RTS; 2188 2189 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2190 } 2191 2192 static int restart_read(struct edgeport_port *edge_port) 2193 { 2194 struct urb *urb; 2195 int status = 0; 2196 unsigned long flags; 2197 2198 spin_lock_irqsave(&edge_port->ep_lock, flags); 2199 2200 if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPED) { 2201 urb = edge_port->port->read_urb; 2202 status = usb_submit_urb(urb, GFP_ATOMIC); 2203 } 2204 edge_port->ep_read_urb_state = EDGE_READ_URB_RUNNING; 2205 edge_port->shadow_mcr |= MCR_RTS; 2206 2207 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2208 2209 return status; 2210 } 2211 2212 static void change_port_settings(struct tty_struct *tty, 2213 struct edgeport_port *edge_port, struct ktermios *old_termios) 2214 { 2215 struct device *dev = &edge_port->port->dev; 2216 struct ump_uart_config *config; 2217 int baud; 2218 unsigned cflag; 2219 int status; 2220 2221 config = kmalloc (sizeof (*config), GFP_KERNEL); 2222 if (!config) { 2223 tty->termios = *old_termios; 2224 return; 2225 } 2226 2227 cflag = tty->termios.c_cflag; 2228 2229 config->wFlags = 0; 2230 2231 /* These flags must be set */ 2232 config->wFlags |= UMP_MASK_UART_FLAGS_RECEIVE_MS_INT; 2233 config->wFlags |= UMP_MASK_UART_FLAGS_AUTO_START_ON_ERR; 2234 config->bUartMode = (u8)(edge_port->bUartMode); 2235 2236 switch (cflag & CSIZE) { 2237 case CS5: 2238 config->bDataBits = UMP_UART_CHAR5BITS; 2239 dev_dbg(dev, "%s - data bits = 5\n", __func__); 2240 break; 2241 case CS6: 2242 config->bDataBits = UMP_UART_CHAR6BITS; 2243 dev_dbg(dev, "%s - data bits = 6\n", __func__); 2244 break; 2245 case CS7: 2246 config->bDataBits = UMP_UART_CHAR7BITS; 2247 dev_dbg(dev, "%s - data bits = 7\n", __func__); 2248 break; 2249 default: 2250 case CS8: 2251 config->bDataBits = UMP_UART_CHAR8BITS; 2252 dev_dbg(dev, "%s - data bits = 8\n", __func__); 2253 break; 2254 } 2255 2256 if (cflag & PARENB) { 2257 if (cflag & PARODD) { 2258 config->wFlags |= UMP_MASK_UART_FLAGS_PARITY; 2259 config->bParity = UMP_UART_ODDPARITY; 2260 dev_dbg(dev, "%s - parity = odd\n", __func__); 2261 } else { 2262 config->wFlags |= UMP_MASK_UART_FLAGS_PARITY; 2263 config->bParity = UMP_UART_EVENPARITY; 2264 dev_dbg(dev, "%s - parity = even\n", __func__); 2265 } 2266 } else { 2267 config->bParity = UMP_UART_NOPARITY; 2268 dev_dbg(dev, "%s - parity = none\n", __func__); 2269 } 2270 2271 if (cflag & CSTOPB) { 2272 config->bStopBits = UMP_UART_STOPBIT2; 2273 dev_dbg(dev, "%s - stop bits = 2\n", __func__); 2274 } else { 2275 config->bStopBits = UMP_UART_STOPBIT1; 2276 dev_dbg(dev, "%s - stop bits = 1\n", __func__); 2277 } 2278 2279 /* figure out the flow control settings */ 2280 if (cflag & CRTSCTS) { 2281 config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X_CTS_FLOW; 2282 config->wFlags |= UMP_MASK_UART_FLAGS_RTS_FLOW; 2283 dev_dbg(dev, "%s - RTS/CTS is enabled\n", __func__); 2284 } else { 2285 dev_dbg(dev, "%s - RTS/CTS is disabled\n", __func__); 2286 restart_read(edge_port); 2287 } 2288 2289 /* 2290 * if we are implementing XON/XOFF, set the start and stop 2291 * character in the device 2292 */ 2293 config->cXon = START_CHAR(tty); 2294 config->cXoff = STOP_CHAR(tty); 2295 2296 /* if we are implementing INBOUND XON/XOFF */ 2297 if (I_IXOFF(tty)) { 2298 config->wFlags |= UMP_MASK_UART_FLAGS_IN_X; 2299 dev_dbg(dev, "%s - INBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n", 2300 __func__, config->cXon, config->cXoff); 2301 } else 2302 dev_dbg(dev, "%s - INBOUND XON/XOFF is disabled\n", __func__); 2303 2304 /* if we are implementing OUTBOUND XON/XOFF */ 2305 if (I_IXON(tty)) { 2306 config->wFlags |= UMP_MASK_UART_FLAGS_OUT_X; 2307 dev_dbg(dev, "%s - OUTBOUND XON/XOFF is enabled, XON = %2x, XOFF = %2x\n", 2308 __func__, config->cXon, config->cXoff); 2309 } else 2310 dev_dbg(dev, "%s - OUTBOUND XON/XOFF is disabled\n", __func__); 2311 2312 tty->termios.c_cflag &= ~CMSPAR; 2313 2314 /* Round the baud rate */ 2315 baud = tty_get_baud_rate(tty); 2316 if (!baud) { 2317 /* pick a default, any default... */ 2318 baud = 9600; 2319 } else { 2320 /* Avoid a zero divisor. */ 2321 baud = min(baud, 461550); 2322 tty_encode_baud_rate(tty, baud, baud); 2323 } 2324 2325 edge_port->baud_rate = baud; 2326 config->wBaudRate = (u16)((461550L + baud/2) / baud); 2327 2328 /* FIXME: Recompute actual baud from divisor here */ 2329 2330 dev_dbg(dev, "%s - baud rate = %d, wBaudRate = %d\n", __func__, baud, config->wBaudRate); 2331 2332 dev_dbg(dev, "wBaudRate: %d\n", (int)(461550L / config->wBaudRate)); 2333 dev_dbg(dev, "wFlags: 0x%x\n", config->wFlags); 2334 dev_dbg(dev, "bDataBits: %d\n", config->bDataBits); 2335 dev_dbg(dev, "bParity: %d\n", config->bParity); 2336 dev_dbg(dev, "bStopBits: %d\n", config->bStopBits); 2337 dev_dbg(dev, "cXon: %d\n", config->cXon); 2338 dev_dbg(dev, "cXoff: %d\n", config->cXoff); 2339 dev_dbg(dev, "bUartMode: %d\n", config->bUartMode); 2340 2341 /* move the word values into big endian mode */ 2342 cpu_to_be16s(&config->wFlags); 2343 cpu_to_be16s(&config->wBaudRate); 2344 2345 status = send_port_cmd(edge_port->port, UMPC_SET_CONFIG, 0, config, 2346 sizeof(*config)); 2347 if (status) 2348 dev_dbg(dev, "%s - error %d when trying to write config to device\n", 2349 __func__, status); 2350 kfree(config); 2351 } 2352 2353 static void edge_set_termios(struct tty_struct *tty, 2354 struct usb_serial_port *port, struct ktermios *old_termios) 2355 { 2356 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2357 2358 if (edge_port == NULL) 2359 return; 2360 /* change the port settings to the new ones specified */ 2361 change_port_settings(tty, edge_port, old_termios); 2362 } 2363 2364 static int edge_tiocmset(struct tty_struct *tty, 2365 unsigned int set, unsigned int clear) 2366 { 2367 struct usb_serial_port *port = tty->driver_data; 2368 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2369 unsigned int mcr; 2370 unsigned long flags; 2371 2372 spin_lock_irqsave(&edge_port->ep_lock, flags); 2373 mcr = edge_port->shadow_mcr; 2374 if (set & TIOCM_RTS) 2375 mcr |= MCR_RTS; 2376 if (set & TIOCM_DTR) 2377 mcr |= MCR_DTR; 2378 if (set & TIOCM_LOOP) 2379 mcr |= MCR_LOOPBACK; 2380 2381 if (clear & TIOCM_RTS) 2382 mcr &= ~MCR_RTS; 2383 if (clear & TIOCM_DTR) 2384 mcr &= ~MCR_DTR; 2385 if (clear & TIOCM_LOOP) 2386 mcr &= ~MCR_LOOPBACK; 2387 2388 edge_port->shadow_mcr = mcr; 2389 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2390 2391 restore_mcr(edge_port, mcr); 2392 return 0; 2393 } 2394 2395 static int edge_tiocmget(struct tty_struct *tty) 2396 { 2397 struct usb_serial_port *port = tty->driver_data; 2398 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2399 unsigned int result = 0; 2400 unsigned int msr; 2401 unsigned int mcr; 2402 unsigned long flags; 2403 2404 spin_lock_irqsave(&edge_port->ep_lock, flags); 2405 2406 msr = edge_port->shadow_msr; 2407 mcr = edge_port->shadow_mcr; 2408 result = ((mcr & MCR_DTR) ? TIOCM_DTR: 0) /* 0x002 */ 2409 | ((mcr & MCR_RTS) ? TIOCM_RTS: 0) /* 0x004 */ 2410 | ((msr & EDGEPORT_MSR_CTS) ? TIOCM_CTS: 0) /* 0x020 */ 2411 | ((msr & EDGEPORT_MSR_CD) ? TIOCM_CAR: 0) /* 0x040 */ 2412 | ((msr & EDGEPORT_MSR_RI) ? TIOCM_RI: 0) /* 0x080 */ 2413 | ((msr & EDGEPORT_MSR_DSR) ? TIOCM_DSR: 0); /* 0x100 */ 2414 2415 2416 dev_dbg(&port->dev, "%s -- %x\n", __func__, result); 2417 spin_unlock_irqrestore(&edge_port->ep_lock, flags); 2418 2419 return result; 2420 } 2421 2422 static void edge_break(struct tty_struct *tty, int break_state) 2423 { 2424 struct usb_serial_port *port = tty->driver_data; 2425 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2426 int status; 2427 int bv = 0; /* Off */ 2428 2429 if (break_state == -1) 2430 bv = 1; /* On */ 2431 status = ti_do_config(edge_port, UMPC_SET_CLR_BREAK, bv); 2432 if (status) 2433 dev_dbg(&port->dev, "%s - error %d sending break set/clear command.\n", 2434 __func__, status); 2435 } 2436 2437 static void edge_heartbeat_schedule(struct edgeport_serial *edge_serial) 2438 { 2439 if (!edge_serial->use_heartbeat) 2440 return; 2441 2442 schedule_delayed_work(&edge_serial->heartbeat_work, 2443 FW_HEARTBEAT_SECS * HZ); 2444 } 2445 2446 static void edge_heartbeat_work(struct work_struct *work) 2447 { 2448 struct edgeport_serial *serial; 2449 struct ti_i2c_desc *rom_desc; 2450 2451 serial = container_of(work, struct edgeport_serial, 2452 heartbeat_work.work); 2453 2454 rom_desc = kmalloc(sizeof(*rom_desc), GFP_KERNEL); 2455 2456 /* Descriptor address request is enough to reset the firmware timer */ 2457 if (!rom_desc || !get_descriptor_addr(serial, I2C_DESC_TYPE_ION, 2458 rom_desc)) { 2459 dev_err(&serial->serial->interface->dev, 2460 "%s - Incomplete heartbeat\n", __func__); 2461 } 2462 kfree(rom_desc); 2463 2464 edge_heartbeat_schedule(serial); 2465 } 2466 2467 static int edge_calc_num_ports(struct usb_serial *serial, 2468 struct usb_serial_endpoints *epds) 2469 { 2470 struct device *dev = &serial->interface->dev; 2471 unsigned char num_ports = serial->type->num_ports; 2472 2473 /* Make sure we have the required endpoints when in download mode. */ 2474 if (serial->interface->cur_altsetting->desc.bNumEndpoints > 1) { 2475 if (epds->num_bulk_in < num_ports || 2476 epds->num_bulk_out < num_ports || 2477 epds->num_interrupt_in < 1) { 2478 dev_err(dev, "required endpoints missing\n"); 2479 return -ENODEV; 2480 } 2481 } 2482 2483 return num_ports; 2484 } 2485 2486 static int edge_startup(struct usb_serial *serial) 2487 { 2488 struct edgeport_serial *edge_serial; 2489 int status; 2490 u16 product_id; 2491 2492 /* create our private serial structure */ 2493 edge_serial = kzalloc(sizeof(struct edgeport_serial), GFP_KERNEL); 2494 if (!edge_serial) 2495 return -ENOMEM; 2496 2497 mutex_init(&edge_serial->es_lock); 2498 edge_serial->serial = serial; 2499 INIT_DELAYED_WORK(&edge_serial->heartbeat_work, edge_heartbeat_work); 2500 usb_set_serial_data(serial, edge_serial); 2501 2502 status = download_fw(edge_serial); 2503 if (status < 0) { 2504 kfree(edge_serial); 2505 return status; 2506 } 2507 2508 if (status > 0) 2509 return 1; /* bind but do not register any ports */ 2510 2511 product_id = le16_to_cpu( 2512 edge_serial->serial->dev->descriptor.idProduct); 2513 2514 /* Currently only the EP/416 models require heartbeat support */ 2515 if (edge_serial->fw_version > FW_HEARTBEAT_VERSION_CUTOFF) { 2516 if (product_id == ION_DEVICE_ID_TI_EDGEPORT_416 || 2517 product_id == ION_DEVICE_ID_TI_EDGEPORT_416B) { 2518 edge_serial->use_heartbeat = true; 2519 } 2520 } 2521 2522 edge_heartbeat_schedule(edge_serial); 2523 2524 return 0; 2525 } 2526 2527 static void edge_disconnect(struct usb_serial *serial) 2528 { 2529 struct edgeport_serial *edge_serial = usb_get_serial_data(serial); 2530 2531 cancel_delayed_work_sync(&edge_serial->heartbeat_work); 2532 } 2533 2534 static void edge_release(struct usb_serial *serial) 2535 { 2536 struct edgeport_serial *edge_serial = usb_get_serial_data(serial); 2537 2538 cancel_delayed_work_sync(&edge_serial->heartbeat_work); 2539 kfree(edge_serial); 2540 } 2541 2542 static int edge_port_probe(struct usb_serial_port *port) 2543 { 2544 struct edgeport_port *edge_port; 2545 int ret; 2546 2547 edge_port = kzalloc(sizeof(*edge_port), GFP_KERNEL); 2548 if (!edge_port) 2549 return -ENOMEM; 2550 2551 spin_lock_init(&edge_port->ep_lock); 2552 edge_port->port = port; 2553 edge_port->edge_serial = usb_get_serial_data(port->serial); 2554 edge_port->bUartMode = default_uart_mode; 2555 2556 switch (port->port_number) { 2557 case 0: 2558 edge_port->uart_base = UMPMEM_BASE_UART1; 2559 edge_port->dma_address = UMPD_OEDB1_ADDRESS; 2560 break; 2561 case 1: 2562 edge_port->uart_base = UMPMEM_BASE_UART2; 2563 edge_port->dma_address = UMPD_OEDB2_ADDRESS; 2564 break; 2565 default: 2566 dev_err(&port->dev, "unknown port number\n"); 2567 ret = -ENODEV; 2568 goto err; 2569 } 2570 2571 dev_dbg(&port->dev, 2572 "%s - port_number = %d, uart_base = %04x, dma_address = %04x\n", 2573 __func__, port->port_number, edge_port->uart_base, 2574 edge_port->dma_address); 2575 2576 usb_set_serial_port_data(port, edge_port); 2577 2578 ret = edge_create_sysfs_attrs(port); 2579 if (ret) 2580 goto err; 2581 2582 /* 2583 * The LSR does not tell when the transmitter shift register has 2584 * emptied so add a one-character drain delay. 2585 */ 2586 port->port.drain_delay = 1; 2587 2588 return 0; 2589 err: 2590 kfree(edge_port); 2591 2592 return ret; 2593 } 2594 2595 static void edge_port_remove(struct usb_serial_port *port) 2596 { 2597 struct edgeport_port *edge_port; 2598 2599 edge_port = usb_get_serial_port_data(port); 2600 edge_remove_sysfs_attrs(port); 2601 kfree(edge_port); 2602 } 2603 2604 /* Sysfs Attributes */ 2605 2606 static ssize_t uart_mode_show(struct device *dev, 2607 struct device_attribute *attr, char *buf) 2608 { 2609 struct usb_serial_port *port = to_usb_serial_port(dev); 2610 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2611 2612 return sprintf(buf, "%d\n", edge_port->bUartMode); 2613 } 2614 2615 static ssize_t uart_mode_store(struct device *dev, 2616 struct device_attribute *attr, const char *valbuf, size_t count) 2617 { 2618 struct usb_serial_port *port = to_usb_serial_port(dev); 2619 struct edgeport_port *edge_port = usb_get_serial_port_data(port); 2620 unsigned int v = simple_strtoul(valbuf, NULL, 0); 2621 2622 dev_dbg(dev, "%s: setting uart_mode = %d\n", __func__, v); 2623 2624 if (v < 256) 2625 edge_port->bUartMode = v; 2626 else 2627 dev_err(dev, "%s - uart_mode %d is invalid\n", __func__, v); 2628 2629 return count; 2630 } 2631 static DEVICE_ATTR_RW(uart_mode); 2632 2633 static int edge_create_sysfs_attrs(struct usb_serial_port *port) 2634 { 2635 return device_create_file(&port->dev, &dev_attr_uart_mode); 2636 } 2637 2638 static int edge_remove_sysfs_attrs(struct usb_serial_port *port) 2639 { 2640 device_remove_file(&port->dev, &dev_attr_uart_mode); 2641 return 0; 2642 } 2643 2644 #ifdef CONFIG_PM 2645 static int edge_suspend(struct usb_serial *serial, pm_message_t message) 2646 { 2647 struct edgeport_serial *edge_serial = usb_get_serial_data(serial); 2648 2649 cancel_delayed_work_sync(&edge_serial->heartbeat_work); 2650 2651 return 0; 2652 } 2653 2654 static int edge_resume(struct usb_serial *serial) 2655 { 2656 struct edgeport_serial *edge_serial = usb_get_serial_data(serial); 2657 2658 edge_heartbeat_schedule(edge_serial); 2659 2660 return 0; 2661 } 2662 #endif 2663 2664 static struct usb_serial_driver edgeport_1port_device = { 2665 .driver = { 2666 .owner = THIS_MODULE, 2667 .name = "edgeport_ti_1", 2668 }, 2669 .description = "Edgeport TI 1 port adapter", 2670 .id_table = edgeport_1port_id_table, 2671 .num_ports = 1, 2672 .num_bulk_out = 1, 2673 .open = edge_open, 2674 .close = edge_close, 2675 .throttle = edge_throttle, 2676 .unthrottle = edge_unthrottle, 2677 .attach = edge_startup, 2678 .calc_num_ports = edge_calc_num_ports, 2679 .disconnect = edge_disconnect, 2680 .release = edge_release, 2681 .port_probe = edge_port_probe, 2682 .port_remove = edge_port_remove, 2683 .set_termios = edge_set_termios, 2684 .tiocmget = edge_tiocmget, 2685 .tiocmset = edge_tiocmset, 2686 .tiocmiwait = usb_serial_generic_tiocmiwait, 2687 .get_icount = usb_serial_generic_get_icount, 2688 .write = edge_write, 2689 .write_room = edge_write_room, 2690 .chars_in_buffer = edge_chars_in_buffer, 2691 .tx_empty = edge_tx_empty, 2692 .break_ctl = edge_break, 2693 .read_int_callback = edge_interrupt_callback, 2694 .read_bulk_callback = edge_bulk_in_callback, 2695 .write_bulk_callback = edge_bulk_out_callback, 2696 #ifdef CONFIG_PM 2697 .suspend = edge_suspend, 2698 .resume = edge_resume, 2699 #endif 2700 }; 2701 2702 static struct usb_serial_driver edgeport_2port_device = { 2703 .driver = { 2704 .owner = THIS_MODULE, 2705 .name = "edgeport_ti_2", 2706 }, 2707 .description = "Edgeport TI 2 port adapter", 2708 .id_table = edgeport_2port_id_table, 2709 .num_ports = 2, 2710 .num_bulk_out = 1, 2711 .open = edge_open, 2712 .close = edge_close, 2713 .throttle = edge_throttle, 2714 .unthrottle = edge_unthrottle, 2715 .attach = edge_startup, 2716 .calc_num_ports = edge_calc_num_ports, 2717 .disconnect = edge_disconnect, 2718 .release = edge_release, 2719 .port_probe = edge_port_probe, 2720 .port_remove = edge_port_remove, 2721 .set_termios = edge_set_termios, 2722 .tiocmget = edge_tiocmget, 2723 .tiocmset = edge_tiocmset, 2724 .tiocmiwait = usb_serial_generic_tiocmiwait, 2725 .get_icount = usb_serial_generic_get_icount, 2726 .write = edge_write, 2727 .write_room = edge_write_room, 2728 .chars_in_buffer = edge_chars_in_buffer, 2729 .tx_empty = edge_tx_empty, 2730 .break_ctl = edge_break, 2731 .read_int_callback = edge_interrupt_callback, 2732 .read_bulk_callback = edge_bulk_in_callback, 2733 .write_bulk_callback = edge_bulk_out_callback, 2734 #ifdef CONFIG_PM 2735 .suspend = edge_suspend, 2736 .resume = edge_resume, 2737 #endif 2738 }; 2739 2740 static struct usb_serial_driver * const serial_drivers[] = { 2741 &edgeport_1port_device, &edgeport_2port_device, NULL 2742 }; 2743 2744 module_usb_serial_driver(serial_drivers, id_table_combined); 2745 2746 MODULE_AUTHOR(DRIVER_AUTHOR); 2747 MODULE_DESCRIPTION(DRIVER_DESC); 2748 MODULE_LICENSE("GPL"); 2749 MODULE_FIRMWARE("edgeport/down3.bin"); 2750 2751 module_param(ignore_cpu_rev, bool, 0644); 2752 MODULE_PARM_DESC(ignore_cpu_rev, 2753 "Ignore the cpu revision when connecting to a device"); 2754 2755 module_param(default_uart_mode, int, 0644); 2756 MODULE_PARM_DESC(default_uart_mode, "Default uart_mode, 0=RS232, ..."); 2757