1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * F81532/F81534 USB to Serial Ports Bridge 4 * 5 * F81532 => 2 Serial Ports 6 * F81534 => 4 Serial Ports 7 * 8 * Copyright (C) 2016 Feature Integration Technology Inc., (Fintek) 9 * Copyright (C) 2016 Tom Tsai (Tom_Tsai@fintek.com.tw) 10 * Copyright (C) 2016 Peter Hong (Peter_Hong@fintek.com.tw) 11 * 12 * The F81532/F81534 had 1 control endpoint for setting, 1 endpoint bulk-out 13 * for all serial port TX and 1 endpoint bulk-in for all serial port read in 14 * (Read Data/MSR/LSR). 15 * 16 * Write URB is fixed with 512bytes, per serial port used 128Bytes. 17 * It can be described by f81534_prepare_write_buffer() 18 * 19 * Read URB is 512Bytes max, per serial port used 128Bytes. 20 * It can be described by f81534_process_read_urb() and maybe received with 21 * 128x1,2,3,4 bytes. 22 * 23 */ 24 #include <linux/slab.h> 25 #include <linux/tty.h> 26 #include <linux/tty_flip.h> 27 #include <linux/usb.h> 28 #include <linux/usb/serial.h> 29 #include <linux/serial_reg.h> 30 #include <linux/module.h> 31 #include <linux/uaccess.h> 32 33 /* Serial Port register Address */ 34 #define F81534_UART_BASE_ADDRESS 0x1200 35 #define F81534_UART_OFFSET 0x10 36 #define F81534_DIVISOR_LSB_REG (0x00 + F81534_UART_BASE_ADDRESS) 37 #define F81534_DIVISOR_MSB_REG (0x01 + F81534_UART_BASE_ADDRESS) 38 #define F81534_INTERRUPT_ENABLE_REG (0x01 + F81534_UART_BASE_ADDRESS) 39 #define F81534_FIFO_CONTROL_REG (0x02 + F81534_UART_BASE_ADDRESS) 40 #define F81534_LINE_CONTROL_REG (0x03 + F81534_UART_BASE_ADDRESS) 41 #define F81534_MODEM_CONTROL_REG (0x04 + F81534_UART_BASE_ADDRESS) 42 #define F81534_LINE_STATUS_REG (0x05 + F81534_UART_BASE_ADDRESS) 43 #define F81534_MODEM_STATUS_REG (0x06 + F81534_UART_BASE_ADDRESS) 44 #define F81534_CLOCK_REG (0x08 + F81534_UART_BASE_ADDRESS) 45 #define F81534_CONFIG1_REG (0x09 + F81534_UART_BASE_ADDRESS) 46 47 #define F81534_DEF_CONF_ADDRESS_START 0x3000 48 #define F81534_DEF_CONF_SIZE 12 49 50 #define F81534_CUSTOM_ADDRESS_START 0x2f00 51 #define F81534_CUSTOM_DATA_SIZE 0x10 52 #define F81534_CUSTOM_NO_CUSTOM_DATA 0xff 53 #define F81534_CUSTOM_VALID_TOKEN 0xf0 54 #define F81534_CONF_OFFSET 1 55 #define F81534_CONF_INIT_GPIO_OFFSET 4 56 #define F81534_CONF_WORK_GPIO_OFFSET 8 57 #define F81534_CONF_GPIO_SHUTDOWN 7 58 #define F81534_CONF_GPIO_RS232 1 59 60 #define F81534_MAX_DATA_BLOCK 64 61 #define F81534_MAX_BUS_RETRY 20 62 63 /* Default URB timeout for USB operations */ 64 #define F81534_USB_MAX_RETRY 10 65 #define F81534_USB_TIMEOUT 2000 66 #define F81534_SET_GET_REGISTER 0xA0 67 68 #define F81534_NUM_PORT 4 69 #define F81534_UNUSED_PORT 0xff 70 #define F81534_WRITE_BUFFER_SIZE 512 71 72 #define DRIVER_DESC "Fintek F81532/F81534" 73 #define FINTEK_VENDOR_ID_1 0x1934 74 #define FINTEK_VENDOR_ID_2 0x2C42 75 #define FINTEK_DEVICE_ID 0x1202 76 #define F81534_MAX_TX_SIZE 124 77 #define F81534_MAX_RX_SIZE 124 78 #define F81534_RECEIVE_BLOCK_SIZE 128 79 #define F81534_MAX_RECEIVE_BLOCK_SIZE 512 80 81 #define F81534_TOKEN_RECEIVE 0x01 82 #define F81534_TOKEN_WRITE 0x02 83 #define F81534_TOKEN_TX_EMPTY 0x03 84 #define F81534_TOKEN_MSR_CHANGE 0x04 85 86 /* 87 * We used interal SPI bus to access FLASH section. We must wait the SPI bus to 88 * idle if we performed any command. 89 * 90 * SPI Bus status register: F81534_BUS_REG_STATUS 91 * Bit 0/1 : BUSY 92 * Bit 2 : IDLE 93 */ 94 #define F81534_BUS_BUSY (BIT(0) | BIT(1)) 95 #define F81534_BUS_IDLE BIT(2) 96 #define F81534_BUS_READ_DATA 0x1004 97 #define F81534_BUS_REG_STATUS 0x1003 98 #define F81534_BUS_REG_START 0x1002 99 #define F81534_BUS_REG_END 0x1001 100 101 #define F81534_CMD_READ 0x03 102 103 #define F81534_DEFAULT_BAUD_RATE 9600 104 105 #define F81534_PORT_CONF_RS232 0 106 #define F81534_PORT_CONF_RS485 BIT(0) 107 #define F81534_PORT_CONF_RS485_INVERT (BIT(0) | BIT(1)) 108 #define F81534_PORT_CONF_MODE_MASK GENMASK(1, 0) 109 #define F81534_PORT_CONF_DISABLE_PORT BIT(3) 110 #define F81534_PORT_CONF_NOT_EXIST_PORT BIT(7) 111 #define F81534_PORT_UNAVAILABLE \ 112 (F81534_PORT_CONF_DISABLE_PORT | F81534_PORT_CONF_NOT_EXIST_PORT) 113 114 115 #define F81534_1X_RXTRIGGER 0xc3 116 #define F81534_8X_RXTRIGGER 0xcf 117 118 /* 119 * F81532/534 Clock registers (offset +08h) 120 * 121 * Bit0: UART Enable (always on) 122 * Bit2-1: Clock source selector 123 * 00: 1.846MHz. 124 * 01: 18.46MHz. 125 * 10: 24MHz. 126 * 11: 14.77MHz. 127 * Bit4: Auto direction(RTS) control (RTS pin Low when TX) 128 * Bit5: Invert direction(RTS) when Bit4 enabled (RTS pin high when TX) 129 */ 130 131 #define F81534_UART_EN BIT(0) 132 #define F81534_CLK_1_846_MHZ 0 133 #define F81534_CLK_18_46_MHZ BIT(1) 134 #define F81534_CLK_24_MHZ BIT(2) 135 #define F81534_CLK_14_77_MHZ (BIT(1) | BIT(2)) 136 #define F81534_CLK_MASK GENMASK(2, 1) 137 #define F81534_CLK_TX_DELAY_1BIT BIT(3) 138 #define F81534_CLK_RS485_MODE BIT(4) 139 #define F81534_CLK_RS485_INVERT BIT(5) 140 141 static const struct usb_device_id f81534_id_table[] = { 142 { USB_DEVICE(FINTEK_VENDOR_ID_1, FINTEK_DEVICE_ID) }, 143 { USB_DEVICE(FINTEK_VENDOR_ID_2, FINTEK_DEVICE_ID) }, 144 {} /* Terminating entry */ 145 }; 146 147 #define F81534_TX_EMPTY_BIT 0 148 149 struct f81534_serial_private { 150 u8 conf_data[F81534_DEF_CONF_SIZE]; 151 int tty_idx[F81534_NUM_PORT]; 152 u8 setting_idx; 153 int opened_port; 154 struct mutex urb_mutex; 155 }; 156 157 struct f81534_port_private { 158 struct mutex mcr_mutex; 159 struct mutex lcr_mutex; 160 struct work_struct lsr_work; 161 struct usb_serial_port *port; 162 unsigned long tx_empty; 163 spinlock_t msr_lock; 164 u32 baud_base; 165 u8 shadow_mcr; 166 u8 shadow_lcr; 167 u8 shadow_msr; 168 u8 shadow_clk; 169 u8 phy_num; 170 }; 171 172 struct f81534_pin_data { 173 const u16 reg_addr; 174 const u8 reg_mask; 175 }; 176 177 struct f81534_port_out_pin { 178 struct f81534_pin_data pin[3]; 179 }; 180 181 /* Pin output value for M2/M1/M0(SD) */ 182 static const struct f81534_port_out_pin f81534_port_out_pins[] = { 183 { { { 0x2ae8, BIT(7) }, { 0x2a90, BIT(5) }, { 0x2a90, BIT(4) } } }, 184 { { { 0x2ae8, BIT(6) }, { 0x2ae8, BIT(0) }, { 0x2ae8, BIT(3) } } }, 185 { { { 0x2a90, BIT(0) }, { 0x2ae8, BIT(2) }, { 0x2a80, BIT(6) } } }, 186 { { { 0x2a90, BIT(3) }, { 0x2a90, BIT(2) }, { 0x2a90, BIT(1) } } }, 187 }; 188 189 static u32 const baudrate_table[] = { 115200, 921600, 1152000, 1500000 }; 190 static u8 const clock_table[] = { F81534_CLK_1_846_MHZ, F81534_CLK_14_77_MHZ, 191 F81534_CLK_18_46_MHZ, F81534_CLK_24_MHZ }; 192 193 static int f81534_logic_to_phy_port(struct usb_serial *serial, 194 struct usb_serial_port *port) 195 { 196 struct f81534_serial_private *serial_priv = 197 usb_get_serial_data(port->serial); 198 int count = 0; 199 int i; 200 201 for (i = 0; i < F81534_NUM_PORT; ++i) { 202 if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE) 203 continue; 204 205 if (port->port_number == count) 206 return i; 207 208 ++count; 209 } 210 211 return -ENODEV; 212 } 213 214 static int f81534_set_register(struct usb_serial *serial, u16 reg, u8 data) 215 { 216 struct usb_interface *interface = serial->interface; 217 struct usb_device *dev = serial->dev; 218 size_t count = F81534_USB_MAX_RETRY; 219 int status; 220 u8 *tmp; 221 222 tmp = kmalloc(sizeof(u8), GFP_KERNEL); 223 if (!tmp) 224 return -ENOMEM; 225 226 *tmp = data; 227 228 /* 229 * Our device maybe not reply when heavily loading, We'll retry for 230 * F81534_USB_MAX_RETRY times. 231 */ 232 while (count--) { 233 status = usb_control_msg(dev, usb_sndctrlpipe(dev, 0), 234 F81534_SET_GET_REGISTER, 235 USB_TYPE_VENDOR | USB_DIR_OUT, 236 reg, 0, tmp, sizeof(u8), 237 F81534_USB_TIMEOUT); 238 if (status > 0) { 239 status = 0; 240 break; 241 } else if (status == 0) { 242 status = -EIO; 243 } 244 } 245 246 if (status < 0) { 247 dev_err(&interface->dev, "%s: reg: %x data: %x failed: %d\n", 248 __func__, reg, data, status); 249 } 250 251 kfree(tmp); 252 return status; 253 } 254 255 static int f81534_get_register(struct usb_serial *serial, u16 reg, u8 *data) 256 { 257 struct usb_interface *interface = serial->interface; 258 struct usb_device *dev = serial->dev; 259 size_t count = F81534_USB_MAX_RETRY; 260 int status; 261 u8 *tmp; 262 263 tmp = kmalloc(sizeof(u8), GFP_KERNEL); 264 if (!tmp) 265 return -ENOMEM; 266 267 /* 268 * Our device maybe not reply when heavily loading, We'll retry for 269 * F81534_USB_MAX_RETRY times. 270 */ 271 while (count--) { 272 status = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), 273 F81534_SET_GET_REGISTER, 274 USB_TYPE_VENDOR | USB_DIR_IN, 275 reg, 0, tmp, sizeof(u8), 276 F81534_USB_TIMEOUT); 277 if (status > 0) { 278 status = 0; 279 break; 280 } else if (status == 0) { 281 status = -EIO; 282 } 283 } 284 285 if (status < 0) { 286 dev_err(&interface->dev, "%s: reg: %x failed: %d\n", __func__, 287 reg, status); 288 goto end; 289 } 290 291 *data = *tmp; 292 293 end: 294 kfree(tmp); 295 return status; 296 } 297 298 static int f81534_set_mask_register(struct usb_serial *serial, u16 reg, 299 u8 mask, u8 data) 300 { 301 int status; 302 u8 tmp; 303 304 status = f81534_get_register(serial, reg, &tmp); 305 if (status) 306 return status; 307 308 tmp &= ~mask; 309 tmp |= (mask & data); 310 311 return f81534_set_register(serial, reg, tmp); 312 } 313 314 static int f81534_set_phy_port_register(struct usb_serial *serial, int phy, 315 u16 reg, u8 data) 316 { 317 return f81534_set_register(serial, reg + F81534_UART_OFFSET * phy, 318 data); 319 } 320 321 static int f81534_get_phy_port_register(struct usb_serial *serial, int phy, 322 u16 reg, u8 *data) 323 { 324 return f81534_get_register(serial, reg + F81534_UART_OFFSET * phy, 325 data); 326 } 327 328 static int f81534_set_port_register(struct usb_serial_port *port, u16 reg, 329 u8 data) 330 { 331 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 332 333 return f81534_set_register(port->serial, 334 reg + port_priv->phy_num * F81534_UART_OFFSET, data); 335 } 336 337 static int f81534_get_port_register(struct usb_serial_port *port, u16 reg, 338 u8 *data) 339 { 340 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 341 342 return f81534_get_register(port->serial, 343 reg + port_priv->phy_num * F81534_UART_OFFSET, data); 344 } 345 346 /* 347 * If we try to access the internal flash via SPI bus, we should check the bus 348 * status for every command. e.g., F81534_BUS_REG_START/F81534_BUS_REG_END 349 */ 350 static int f81534_wait_for_spi_idle(struct usb_serial *serial) 351 { 352 size_t count = F81534_MAX_BUS_RETRY; 353 u8 tmp; 354 int status; 355 356 do { 357 status = f81534_get_register(serial, F81534_BUS_REG_STATUS, 358 &tmp); 359 if (status) 360 return status; 361 362 if (tmp & F81534_BUS_BUSY) 363 continue; 364 365 if (tmp & F81534_BUS_IDLE) 366 break; 367 368 } while (--count); 369 370 if (!count) { 371 dev_err(&serial->interface->dev, 372 "%s: timed out waiting for idle SPI bus\n", 373 __func__); 374 return -EIO; 375 } 376 377 return f81534_set_register(serial, F81534_BUS_REG_STATUS, 378 tmp & ~F81534_BUS_IDLE); 379 } 380 381 static int f81534_get_spi_register(struct usb_serial *serial, u16 reg, 382 u8 *data) 383 { 384 int status; 385 386 status = f81534_get_register(serial, reg, data); 387 if (status) 388 return status; 389 390 return f81534_wait_for_spi_idle(serial); 391 } 392 393 static int f81534_set_spi_register(struct usb_serial *serial, u16 reg, u8 data) 394 { 395 int status; 396 397 status = f81534_set_register(serial, reg, data); 398 if (status) 399 return status; 400 401 return f81534_wait_for_spi_idle(serial); 402 } 403 404 static int f81534_read_flash(struct usb_serial *serial, u32 address, 405 size_t size, u8 *buf) 406 { 407 u8 tmp_buf[F81534_MAX_DATA_BLOCK]; 408 size_t block = 0; 409 size_t read_size; 410 size_t count; 411 int status; 412 int offset; 413 u16 reg_tmp; 414 415 status = f81534_set_spi_register(serial, F81534_BUS_REG_START, 416 F81534_CMD_READ); 417 if (status) 418 return status; 419 420 status = f81534_set_spi_register(serial, F81534_BUS_REG_START, 421 (address >> 16) & 0xff); 422 if (status) 423 return status; 424 425 status = f81534_set_spi_register(serial, F81534_BUS_REG_START, 426 (address >> 8) & 0xff); 427 if (status) 428 return status; 429 430 status = f81534_set_spi_register(serial, F81534_BUS_REG_START, 431 (address >> 0) & 0xff); 432 if (status) 433 return status; 434 435 /* Continuous read mode */ 436 do { 437 read_size = min_t(size_t, F81534_MAX_DATA_BLOCK, size); 438 439 for (count = 0; count < read_size; ++count) { 440 /* To write F81534_BUS_REG_END when final byte */ 441 if (size <= F81534_MAX_DATA_BLOCK && 442 read_size == count + 1) 443 reg_tmp = F81534_BUS_REG_END; 444 else 445 reg_tmp = F81534_BUS_REG_START; 446 447 /* 448 * Dummy code, force IC to generate a read pulse, the 449 * set of value 0xf1 is dont care (any value is ok) 450 */ 451 status = f81534_set_spi_register(serial, reg_tmp, 452 0xf1); 453 if (status) 454 return status; 455 456 status = f81534_get_spi_register(serial, 457 F81534_BUS_READ_DATA, 458 &tmp_buf[count]); 459 if (status) 460 return status; 461 462 offset = count + block * F81534_MAX_DATA_BLOCK; 463 buf[offset] = tmp_buf[count]; 464 } 465 466 size -= read_size; 467 ++block; 468 } while (size); 469 470 return 0; 471 } 472 473 static void f81534_prepare_write_buffer(struct usb_serial_port *port, u8 *buf) 474 { 475 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 476 int phy_num = port_priv->phy_num; 477 u8 tx_len; 478 int i; 479 480 /* 481 * The block layout is fixed with 4x128 Bytes, per 128 Bytes a port. 482 * index 0: port phy idx (e.g., 0,1,2,3) 483 * index 1: only F81534_TOKEN_WRITE 484 * index 2: serial TX out length 485 * index 3: fix to 0 486 * index 4~127: serial out data block 487 */ 488 for (i = 0; i < F81534_NUM_PORT; ++i) { 489 buf[i * F81534_RECEIVE_BLOCK_SIZE] = i; 490 buf[i * F81534_RECEIVE_BLOCK_SIZE + 1] = F81534_TOKEN_WRITE; 491 buf[i * F81534_RECEIVE_BLOCK_SIZE + 2] = 0; 492 buf[i * F81534_RECEIVE_BLOCK_SIZE + 3] = 0; 493 } 494 495 tx_len = kfifo_out_locked(&port->write_fifo, 496 &buf[phy_num * F81534_RECEIVE_BLOCK_SIZE + 4], 497 F81534_MAX_TX_SIZE, &port->lock); 498 499 buf[phy_num * F81534_RECEIVE_BLOCK_SIZE + 2] = tx_len; 500 } 501 502 static int f81534_submit_writer(struct usb_serial_port *port, gfp_t mem_flags) 503 { 504 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 505 struct urb *urb; 506 unsigned long flags; 507 int result; 508 509 /* Check is any data in write_fifo */ 510 spin_lock_irqsave(&port->lock, flags); 511 512 if (kfifo_is_empty(&port->write_fifo)) { 513 spin_unlock_irqrestore(&port->lock, flags); 514 return 0; 515 } 516 517 spin_unlock_irqrestore(&port->lock, flags); 518 519 /* Check H/W is TXEMPTY */ 520 if (!test_and_clear_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty)) 521 return 0; 522 523 urb = port->write_urbs[0]; 524 f81534_prepare_write_buffer(port, port->bulk_out_buffers[0]); 525 urb->transfer_buffer_length = F81534_WRITE_BUFFER_SIZE; 526 527 result = usb_submit_urb(urb, mem_flags); 528 if (result) { 529 set_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); 530 dev_err(&port->dev, "%s: submit failed: %d\n", __func__, 531 result); 532 return result; 533 } 534 535 usb_serial_port_softint(port); 536 return 0; 537 } 538 539 static u32 f81534_calc_baud_divisor(u32 baudrate, u32 clockrate) 540 { 541 if (!baudrate) 542 return 0; 543 544 /* Round to nearest divisor */ 545 return DIV_ROUND_CLOSEST(clockrate, baudrate); 546 } 547 548 static int f81534_find_clk(u32 baudrate) 549 { 550 int idx; 551 552 for (idx = 0; idx < ARRAY_SIZE(baudrate_table); ++idx) { 553 if (baudrate <= baudrate_table[idx] && 554 baudrate_table[idx] % baudrate == 0) 555 return idx; 556 } 557 558 return -EINVAL; 559 } 560 561 static int f81534_set_port_config(struct usb_serial_port *port, 562 struct tty_struct *tty, u32 baudrate, u32 old_baudrate, u8 lcr) 563 { 564 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 565 u32 divisor; 566 int status; 567 int i; 568 int idx; 569 u8 value; 570 u32 baud_list[] = {baudrate, old_baudrate, F81534_DEFAULT_BAUD_RATE}; 571 572 for (i = 0; i < ARRAY_SIZE(baud_list); ++i) { 573 idx = f81534_find_clk(baud_list[i]); 574 if (idx >= 0) { 575 baudrate = baud_list[i]; 576 tty_encode_baud_rate(tty, baudrate, baudrate); 577 break; 578 } 579 } 580 581 if (idx < 0) 582 return -EINVAL; 583 584 port_priv->baud_base = baudrate_table[idx]; 585 port_priv->shadow_clk &= ~F81534_CLK_MASK; 586 port_priv->shadow_clk |= clock_table[idx]; 587 588 status = f81534_set_port_register(port, F81534_CLOCK_REG, 589 port_priv->shadow_clk); 590 if (status) { 591 dev_err(&port->dev, "CLOCK_REG setting failed\n"); 592 return status; 593 } 594 595 if (baudrate <= 1200) 596 value = F81534_1X_RXTRIGGER; /* 128 FIFO & TL: 1x */ 597 else 598 value = F81534_8X_RXTRIGGER; /* 128 FIFO & TL: 8x */ 599 600 status = f81534_set_port_register(port, F81534_CONFIG1_REG, value); 601 if (status) { 602 dev_err(&port->dev, "%s: CONFIG1 setting failed\n", __func__); 603 return status; 604 } 605 606 if (baudrate <= 1200) 607 value = UART_FCR_TRIGGER_1 | UART_FCR_ENABLE_FIFO; /* TL: 1 */ 608 else 609 value = UART_FCR_TRIGGER_8 | UART_FCR_ENABLE_FIFO; /* TL: 8 */ 610 611 status = f81534_set_port_register(port, F81534_FIFO_CONTROL_REG, 612 value); 613 if (status) { 614 dev_err(&port->dev, "%s: FCR setting failed\n", __func__); 615 return status; 616 } 617 618 divisor = f81534_calc_baud_divisor(baudrate, port_priv->baud_base); 619 620 mutex_lock(&port_priv->lcr_mutex); 621 622 value = UART_LCR_DLAB; 623 status = f81534_set_port_register(port, F81534_LINE_CONTROL_REG, 624 value); 625 if (status) { 626 dev_err(&port->dev, "%s: set LCR failed\n", __func__); 627 goto out_unlock; 628 } 629 630 value = divisor & 0xff; 631 status = f81534_set_port_register(port, F81534_DIVISOR_LSB_REG, value); 632 if (status) { 633 dev_err(&port->dev, "%s: set DLAB LSB failed\n", __func__); 634 goto out_unlock; 635 } 636 637 value = (divisor >> 8) & 0xff; 638 status = f81534_set_port_register(port, F81534_DIVISOR_MSB_REG, value); 639 if (status) { 640 dev_err(&port->dev, "%s: set DLAB MSB failed\n", __func__); 641 goto out_unlock; 642 } 643 644 value = lcr | (port_priv->shadow_lcr & UART_LCR_SBC); 645 status = f81534_set_port_register(port, F81534_LINE_CONTROL_REG, 646 value); 647 if (status) { 648 dev_err(&port->dev, "%s: set LCR failed\n", __func__); 649 goto out_unlock; 650 } 651 652 port_priv->shadow_lcr = value; 653 out_unlock: 654 mutex_unlock(&port_priv->lcr_mutex); 655 656 return status; 657 } 658 659 static void f81534_break_ctl(struct tty_struct *tty, int break_state) 660 { 661 struct usb_serial_port *port = tty->driver_data; 662 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 663 int status; 664 665 mutex_lock(&port_priv->lcr_mutex); 666 667 if (break_state) 668 port_priv->shadow_lcr |= UART_LCR_SBC; 669 else 670 port_priv->shadow_lcr &= ~UART_LCR_SBC; 671 672 status = f81534_set_port_register(port, F81534_LINE_CONTROL_REG, 673 port_priv->shadow_lcr); 674 if (status) 675 dev_err(&port->dev, "set break failed: %d\n", status); 676 677 mutex_unlock(&port_priv->lcr_mutex); 678 } 679 680 static int f81534_update_mctrl(struct usb_serial_port *port, unsigned int set, 681 unsigned int clear) 682 { 683 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 684 int status; 685 u8 tmp; 686 687 if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) 688 return 0; /* no change */ 689 690 mutex_lock(&port_priv->mcr_mutex); 691 692 /* 'Set' takes precedence over 'Clear' */ 693 clear &= ~set; 694 695 /* Always enable UART_MCR_OUT2 */ 696 tmp = UART_MCR_OUT2 | port_priv->shadow_mcr; 697 698 if (clear & TIOCM_DTR) 699 tmp &= ~UART_MCR_DTR; 700 701 if (clear & TIOCM_RTS) 702 tmp &= ~UART_MCR_RTS; 703 704 if (set & TIOCM_DTR) 705 tmp |= UART_MCR_DTR; 706 707 if (set & TIOCM_RTS) 708 tmp |= UART_MCR_RTS; 709 710 status = f81534_set_port_register(port, F81534_MODEM_CONTROL_REG, tmp); 711 if (status < 0) { 712 dev_err(&port->dev, "%s: MCR write failed\n", __func__); 713 mutex_unlock(&port_priv->mcr_mutex); 714 return status; 715 } 716 717 port_priv->shadow_mcr = tmp; 718 mutex_unlock(&port_priv->mcr_mutex); 719 return 0; 720 } 721 722 /* 723 * This function will search the data area with token F81534_CUSTOM_VALID_TOKEN 724 * for latest configuration index. If nothing found 725 * (*index = F81534_CUSTOM_NO_CUSTOM_DATA), We'll load default configure in 726 * F81534_DEF_CONF_ADDRESS_START section. 727 * 728 * Due to we only use block0 to save data, so *index should be 0 or 729 * F81534_CUSTOM_NO_CUSTOM_DATA. 730 */ 731 static int f81534_find_config_idx(struct usb_serial *serial, u8 *index) 732 { 733 u8 tmp; 734 int status; 735 736 status = f81534_read_flash(serial, F81534_CUSTOM_ADDRESS_START, 1, 737 &tmp); 738 if (status) { 739 dev_err(&serial->interface->dev, "%s: read failed: %d\n", 740 __func__, status); 741 return status; 742 } 743 744 /* We'll use the custom data when the data is valid. */ 745 if (tmp == F81534_CUSTOM_VALID_TOKEN) 746 *index = 0; 747 else 748 *index = F81534_CUSTOM_NO_CUSTOM_DATA; 749 750 return 0; 751 } 752 753 /* 754 * The F81532/534 will not report serial port to USB serial subsystem when 755 * H/W DCD/DSR/CTS/RI/RX pin connected to ground. 756 * 757 * To detect RX pin status, we'll enable MCR interal loopback, disable it and 758 * delayed for 60ms. It connected to ground If LSR register report UART_LSR_BI. 759 */ 760 static bool f81534_check_port_hw_disabled(struct usb_serial *serial, int phy) 761 { 762 int status; 763 u8 old_mcr; 764 u8 msr; 765 u8 lsr; 766 u8 msr_mask; 767 768 msr_mask = UART_MSR_DCD | UART_MSR_RI | UART_MSR_DSR | UART_MSR_CTS; 769 770 status = f81534_get_phy_port_register(serial, phy, 771 F81534_MODEM_STATUS_REG, &msr); 772 if (status) 773 return false; 774 775 if ((msr & msr_mask) != msr_mask) 776 return false; 777 778 status = f81534_set_phy_port_register(serial, phy, 779 F81534_FIFO_CONTROL_REG, UART_FCR_ENABLE_FIFO | 780 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); 781 if (status) 782 return false; 783 784 status = f81534_get_phy_port_register(serial, phy, 785 F81534_MODEM_CONTROL_REG, &old_mcr); 786 if (status) 787 return false; 788 789 status = f81534_set_phy_port_register(serial, phy, 790 F81534_MODEM_CONTROL_REG, UART_MCR_LOOP); 791 if (status) 792 return false; 793 794 status = f81534_set_phy_port_register(serial, phy, 795 F81534_MODEM_CONTROL_REG, 0x0); 796 if (status) 797 return false; 798 799 msleep(60); 800 801 status = f81534_get_phy_port_register(serial, phy, 802 F81534_LINE_STATUS_REG, &lsr); 803 if (status) 804 return false; 805 806 status = f81534_set_phy_port_register(serial, phy, 807 F81534_MODEM_CONTROL_REG, old_mcr); 808 if (status) 809 return false; 810 811 if ((lsr & UART_LSR_BI) == UART_LSR_BI) 812 return true; 813 814 return false; 815 } 816 817 /* 818 * We had 2 generation of F81532/534 IC. All has an internal storage. 819 * 820 * 1st is pure USB-to-TTL RS232 IC and designed for 4 ports only, no any 821 * internal data will used. All mode and gpio control should manually set 822 * by AP or Driver and all storage space value are 0xff. The 823 * f81534_calc_num_ports() will run to final we marked as "oldest version" 824 * for this IC. 825 * 826 * 2rd is designed to more generic to use any transceiver and this is our 827 * mass production type. We'll save data in F81534_CUSTOM_ADDRESS_START 828 * (0x2f00) with 9bytes. The 1st byte is a indicater. If the token is 829 * F81534_CUSTOM_VALID_TOKEN(0xf0), the IC is 2nd gen type, the following 830 * 4bytes save port mode (0:RS232/1:RS485 Invert/2:RS485), and the last 831 * 4bytes save GPIO state(value from 0~7 to represent 3 GPIO output pin). 832 * The f81534_calc_num_ports() will run to "new style" with checking 833 * F81534_PORT_UNAVAILABLE section. 834 */ 835 static int f81534_calc_num_ports(struct usb_serial *serial, 836 struct usb_serial_endpoints *epds) 837 { 838 struct f81534_serial_private *serial_priv; 839 struct device *dev = &serial->interface->dev; 840 int size_bulk_in = usb_endpoint_maxp(epds->bulk_in[0]); 841 int size_bulk_out = usb_endpoint_maxp(epds->bulk_out[0]); 842 u8 num_port = 0; 843 int index = 0; 844 int status; 845 int i; 846 847 if (size_bulk_out != F81534_WRITE_BUFFER_SIZE || 848 size_bulk_in != F81534_MAX_RECEIVE_BLOCK_SIZE) { 849 dev_err(dev, "unsupported endpoint max packet size\n"); 850 return -ENODEV; 851 } 852 853 serial_priv = devm_kzalloc(&serial->interface->dev, 854 sizeof(*serial_priv), GFP_KERNEL); 855 if (!serial_priv) 856 return -ENOMEM; 857 858 usb_set_serial_data(serial, serial_priv); 859 mutex_init(&serial_priv->urb_mutex); 860 861 /* Check had custom setting */ 862 status = f81534_find_config_idx(serial, &serial_priv->setting_idx); 863 if (status) { 864 dev_err(&serial->interface->dev, "%s: find idx failed: %d\n", 865 __func__, status); 866 return status; 867 } 868 869 /* 870 * We'll read custom data only when data available, otherwise we'll 871 * read default value instead. 872 */ 873 if (serial_priv->setting_idx != F81534_CUSTOM_NO_CUSTOM_DATA) { 874 status = f81534_read_flash(serial, 875 F81534_CUSTOM_ADDRESS_START + 876 F81534_CONF_OFFSET, 877 sizeof(serial_priv->conf_data), 878 serial_priv->conf_data); 879 if (status) { 880 dev_err(&serial->interface->dev, 881 "%s: get custom data failed: %d\n", 882 __func__, status); 883 return status; 884 } 885 886 dev_dbg(&serial->interface->dev, 887 "%s: read config from block: %d\n", __func__, 888 serial_priv->setting_idx); 889 } else { 890 /* Read default board setting */ 891 status = f81534_read_flash(serial, 892 F81534_DEF_CONF_ADDRESS_START, 893 sizeof(serial_priv->conf_data), 894 serial_priv->conf_data); 895 if (status) { 896 dev_err(&serial->interface->dev, 897 "%s: read failed: %d\n", __func__, 898 status); 899 return status; 900 } 901 902 dev_dbg(&serial->interface->dev, "%s: read default config\n", 903 __func__); 904 } 905 906 /* New style, find all possible ports */ 907 for (i = 0; i < F81534_NUM_PORT; ++i) { 908 if (f81534_check_port_hw_disabled(serial, i)) 909 serial_priv->conf_data[i] |= F81534_PORT_UNAVAILABLE; 910 911 if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE) 912 continue; 913 914 ++num_port; 915 } 916 917 if (!num_port) { 918 dev_warn(&serial->interface->dev, 919 "no config found, assuming 4 ports\n"); 920 num_port = 4; /* Nothing found, oldest version IC */ 921 } 922 923 /* Assign phy-to-logic mapping */ 924 for (i = 0; i < F81534_NUM_PORT; ++i) { 925 if (serial_priv->conf_data[i] & F81534_PORT_UNAVAILABLE) 926 continue; 927 928 serial_priv->tty_idx[i] = index++; 929 dev_dbg(&serial->interface->dev, 930 "%s: phy_num: %d, tty_idx: %d\n", __func__, i, 931 serial_priv->tty_idx[i]); 932 } 933 934 /* 935 * Setup bulk-out endpoint multiplexing. All ports share the same 936 * bulk-out endpoint. 937 */ 938 BUILD_BUG_ON(ARRAY_SIZE(epds->bulk_out) < F81534_NUM_PORT); 939 940 for (i = 1; i < num_port; ++i) 941 epds->bulk_out[i] = epds->bulk_out[0]; 942 943 epds->num_bulk_out = num_port; 944 945 return num_port; 946 } 947 948 static void f81534_set_termios(struct tty_struct *tty, 949 struct usb_serial_port *port, 950 struct ktermios *old_termios) 951 { 952 u8 new_lcr = 0; 953 int status; 954 u32 baud; 955 u32 old_baud; 956 957 if (C_BAUD(tty) == B0) 958 f81534_update_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS); 959 else if (old_termios && (old_termios->c_cflag & CBAUD) == B0) 960 f81534_update_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0); 961 962 if (C_PARENB(tty)) { 963 new_lcr |= UART_LCR_PARITY; 964 965 if (!C_PARODD(tty)) 966 new_lcr |= UART_LCR_EPAR; 967 968 if (C_CMSPAR(tty)) 969 new_lcr |= UART_LCR_SPAR; 970 } 971 972 if (C_CSTOPB(tty)) 973 new_lcr |= UART_LCR_STOP; 974 975 switch (C_CSIZE(tty)) { 976 case CS5: 977 new_lcr |= UART_LCR_WLEN5; 978 break; 979 case CS6: 980 new_lcr |= UART_LCR_WLEN6; 981 break; 982 case CS7: 983 new_lcr |= UART_LCR_WLEN7; 984 break; 985 default: 986 case CS8: 987 new_lcr |= UART_LCR_WLEN8; 988 break; 989 } 990 991 baud = tty_get_baud_rate(tty); 992 if (!baud) 993 return; 994 995 if (old_termios) 996 old_baud = tty_termios_baud_rate(old_termios); 997 else 998 old_baud = F81534_DEFAULT_BAUD_RATE; 999 1000 dev_dbg(&port->dev, "%s: baud: %d\n", __func__, baud); 1001 1002 status = f81534_set_port_config(port, tty, baud, old_baud, new_lcr); 1003 if (status < 0) { 1004 dev_err(&port->dev, "%s: set port config failed: %d\n", 1005 __func__, status); 1006 } 1007 } 1008 1009 static int f81534_submit_read_urb(struct usb_serial *serial, gfp_t flags) 1010 { 1011 return usb_serial_generic_submit_read_urbs(serial->port[0], flags); 1012 } 1013 1014 static void f81534_msr_changed(struct usb_serial_port *port, u8 msr) 1015 { 1016 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1017 struct tty_struct *tty; 1018 unsigned long flags; 1019 u8 old_msr; 1020 1021 if (!(msr & UART_MSR_ANY_DELTA)) 1022 return; 1023 1024 spin_lock_irqsave(&port_priv->msr_lock, flags); 1025 old_msr = port_priv->shadow_msr; 1026 port_priv->shadow_msr = msr; 1027 spin_unlock_irqrestore(&port_priv->msr_lock, flags); 1028 1029 dev_dbg(&port->dev, "%s: MSR from %02x to %02x\n", __func__, old_msr, 1030 msr); 1031 1032 /* Update input line counters */ 1033 if (msr & UART_MSR_DCTS) 1034 port->icount.cts++; 1035 if (msr & UART_MSR_DDSR) 1036 port->icount.dsr++; 1037 if (msr & UART_MSR_DDCD) 1038 port->icount.dcd++; 1039 if (msr & UART_MSR_TERI) 1040 port->icount.rng++; 1041 1042 wake_up_interruptible(&port->port.delta_msr_wait); 1043 1044 if (!(msr & UART_MSR_DDCD)) 1045 return; 1046 1047 dev_dbg(&port->dev, "%s: DCD Changed: phy_num: %d from %x to %x\n", 1048 __func__, port_priv->phy_num, old_msr, msr); 1049 1050 tty = tty_port_tty_get(&port->port); 1051 if (!tty) 1052 return; 1053 1054 usb_serial_handle_dcd_change(port, tty, msr & UART_MSR_DCD); 1055 tty_kref_put(tty); 1056 } 1057 1058 static int f81534_read_msr(struct usb_serial_port *port) 1059 { 1060 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1061 unsigned long flags; 1062 int status; 1063 u8 msr; 1064 1065 /* Get MSR initial value */ 1066 status = f81534_get_port_register(port, F81534_MODEM_STATUS_REG, &msr); 1067 if (status) 1068 return status; 1069 1070 /* Force update current state */ 1071 spin_lock_irqsave(&port_priv->msr_lock, flags); 1072 port_priv->shadow_msr = msr; 1073 spin_unlock_irqrestore(&port_priv->msr_lock, flags); 1074 1075 return 0; 1076 } 1077 1078 static int f81534_open(struct tty_struct *tty, struct usb_serial_port *port) 1079 { 1080 struct f81534_serial_private *serial_priv = 1081 usb_get_serial_data(port->serial); 1082 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1083 int status; 1084 1085 status = f81534_set_port_register(port, 1086 F81534_FIFO_CONTROL_REG, UART_FCR_ENABLE_FIFO | 1087 UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); 1088 if (status) { 1089 dev_err(&port->dev, "%s: Clear FIFO failed: %d\n", __func__, 1090 status); 1091 return status; 1092 } 1093 1094 if (tty) 1095 f81534_set_termios(tty, port, NULL); 1096 1097 status = f81534_read_msr(port); 1098 if (status) 1099 return status; 1100 1101 mutex_lock(&serial_priv->urb_mutex); 1102 1103 /* Submit Read URBs for first port opened */ 1104 if (!serial_priv->opened_port) { 1105 status = f81534_submit_read_urb(port->serial, GFP_KERNEL); 1106 if (status) 1107 goto exit; 1108 } 1109 1110 serial_priv->opened_port++; 1111 1112 exit: 1113 mutex_unlock(&serial_priv->urb_mutex); 1114 1115 set_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); 1116 return status; 1117 } 1118 1119 static void f81534_close(struct usb_serial_port *port) 1120 { 1121 struct f81534_serial_private *serial_priv = 1122 usb_get_serial_data(port->serial); 1123 struct usb_serial_port *port0 = port->serial->port[0]; 1124 unsigned long flags; 1125 size_t i; 1126 1127 usb_kill_urb(port->write_urbs[0]); 1128 1129 spin_lock_irqsave(&port->lock, flags); 1130 kfifo_reset_out(&port->write_fifo); 1131 spin_unlock_irqrestore(&port->lock, flags); 1132 1133 /* Kill Read URBs when final port closed */ 1134 mutex_lock(&serial_priv->urb_mutex); 1135 serial_priv->opened_port--; 1136 1137 if (!serial_priv->opened_port) { 1138 for (i = 0; i < ARRAY_SIZE(port0->read_urbs); ++i) 1139 usb_kill_urb(port0->read_urbs[i]); 1140 } 1141 1142 mutex_unlock(&serial_priv->urb_mutex); 1143 } 1144 1145 static int f81534_get_serial_info(struct tty_struct *tty, 1146 struct serial_struct *ss) 1147 { 1148 struct usb_serial_port *port = tty->driver_data; 1149 struct f81534_port_private *port_priv; 1150 1151 port_priv = usb_get_serial_port_data(port); 1152 1153 ss->type = PORT_16550A; 1154 ss->port = port->port_number; 1155 ss->line = port->minor; 1156 ss->baud_base = port_priv->baud_base; 1157 return 0; 1158 } 1159 1160 static void f81534_process_per_serial_block(struct usb_serial_port *port, 1161 u8 *data) 1162 { 1163 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1164 int phy_num = data[0]; 1165 size_t read_size = 0; 1166 size_t i; 1167 char tty_flag; 1168 int status; 1169 u8 lsr; 1170 1171 /* 1172 * The block layout is 128 Bytes 1173 * index 0: port phy idx (e.g., 0,1,2,3), 1174 * index 1: It's could be 1175 * F81534_TOKEN_RECEIVE 1176 * F81534_TOKEN_TX_EMPTY 1177 * F81534_TOKEN_MSR_CHANGE 1178 * index 2: serial in size (data+lsr, must be even) 1179 * meaningful for F81534_TOKEN_RECEIVE only 1180 * index 3: current MSR with this device 1181 * index 4~127: serial in data block (data+lsr, must be even) 1182 */ 1183 switch (data[1]) { 1184 case F81534_TOKEN_TX_EMPTY: 1185 set_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); 1186 1187 /* Try to submit writer */ 1188 status = f81534_submit_writer(port, GFP_ATOMIC); 1189 if (status) 1190 dev_err(&port->dev, "%s: submit failed\n", __func__); 1191 return; 1192 1193 case F81534_TOKEN_MSR_CHANGE: 1194 f81534_msr_changed(port, data[3]); 1195 return; 1196 1197 case F81534_TOKEN_RECEIVE: 1198 read_size = data[2]; 1199 if (read_size > F81534_MAX_RX_SIZE) { 1200 dev_err(&port->dev, 1201 "%s: phy: %d read_size: %zu larger than: %d\n", 1202 __func__, phy_num, read_size, 1203 F81534_MAX_RX_SIZE); 1204 return; 1205 } 1206 1207 break; 1208 1209 default: 1210 dev_warn(&port->dev, "%s: unknown token: %02x\n", __func__, 1211 data[1]); 1212 return; 1213 } 1214 1215 for (i = 4; i < 4 + read_size; i += 2) { 1216 tty_flag = TTY_NORMAL; 1217 lsr = data[i + 1]; 1218 1219 if (lsr & UART_LSR_BRK_ERROR_BITS) { 1220 if (lsr & UART_LSR_BI) { 1221 tty_flag = TTY_BREAK; 1222 port->icount.brk++; 1223 usb_serial_handle_break(port); 1224 } else if (lsr & UART_LSR_PE) { 1225 tty_flag = TTY_PARITY; 1226 port->icount.parity++; 1227 } else if (lsr & UART_LSR_FE) { 1228 tty_flag = TTY_FRAME; 1229 port->icount.frame++; 1230 } 1231 1232 if (lsr & UART_LSR_OE) { 1233 port->icount.overrun++; 1234 tty_insert_flip_char(&port->port, 0, 1235 TTY_OVERRUN); 1236 } 1237 1238 schedule_work(&port_priv->lsr_work); 1239 } 1240 1241 if (port->sysrq) { 1242 if (usb_serial_handle_sysrq_char(port, data[i])) 1243 continue; 1244 } 1245 1246 tty_insert_flip_char(&port->port, data[i], tty_flag); 1247 } 1248 1249 tty_flip_buffer_push(&port->port); 1250 } 1251 1252 static void f81534_process_read_urb(struct urb *urb) 1253 { 1254 struct f81534_serial_private *serial_priv; 1255 struct usb_serial_port *port; 1256 struct usb_serial *serial; 1257 u8 *buf; 1258 int phy_port_num; 1259 int tty_port_num; 1260 size_t i; 1261 1262 if (!urb->actual_length || 1263 urb->actual_length % F81534_RECEIVE_BLOCK_SIZE) { 1264 return; 1265 } 1266 1267 port = urb->context; 1268 serial = port->serial; 1269 buf = urb->transfer_buffer; 1270 serial_priv = usb_get_serial_data(serial); 1271 1272 for (i = 0; i < urb->actual_length; i += F81534_RECEIVE_BLOCK_SIZE) { 1273 phy_port_num = buf[i]; 1274 if (phy_port_num >= F81534_NUM_PORT) { 1275 dev_err(&port->dev, 1276 "%s: phy_port_num: %d larger than: %d\n", 1277 __func__, phy_port_num, F81534_NUM_PORT); 1278 continue; 1279 } 1280 1281 tty_port_num = serial_priv->tty_idx[phy_port_num]; 1282 port = serial->port[tty_port_num]; 1283 1284 if (tty_port_initialized(&port->port)) 1285 f81534_process_per_serial_block(port, &buf[i]); 1286 } 1287 } 1288 1289 static void f81534_write_usb_callback(struct urb *urb) 1290 { 1291 struct usb_serial_port *port = urb->context; 1292 1293 switch (urb->status) { 1294 case 0: 1295 break; 1296 case -ENOENT: 1297 case -ECONNRESET: 1298 case -ESHUTDOWN: 1299 dev_dbg(&port->dev, "%s - urb stopped: %d\n", 1300 __func__, urb->status); 1301 return; 1302 case -EPIPE: 1303 dev_err(&port->dev, "%s - urb stopped: %d\n", 1304 __func__, urb->status); 1305 return; 1306 default: 1307 dev_dbg(&port->dev, "%s - nonzero urb status: %d\n", 1308 __func__, urb->status); 1309 break; 1310 } 1311 } 1312 1313 static void f81534_lsr_worker(struct work_struct *work) 1314 { 1315 struct f81534_port_private *port_priv; 1316 struct usb_serial_port *port; 1317 int status; 1318 u8 tmp; 1319 1320 port_priv = container_of(work, struct f81534_port_private, lsr_work); 1321 port = port_priv->port; 1322 1323 status = f81534_get_port_register(port, F81534_LINE_STATUS_REG, &tmp); 1324 if (status) 1325 dev_warn(&port->dev, "read LSR failed: %d\n", status); 1326 } 1327 1328 static int f81534_set_port_output_pin(struct usb_serial_port *port) 1329 { 1330 struct f81534_serial_private *serial_priv; 1331 struct f81534_port_private *port_priv; 1332 struct usb_serial *serial; 1333 const struct f81534_port_out_pin *pins; 1334 int status; 1335 int i; 1336 u8 value; 1337 u8 idx; 1338 1339 serial = port->serial; 1340 serial_priv = usb_get_serial_data(serial); 1341 port_priv = usb_get_serial_port_data(port); 1342 1343 idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num; 1344 value = serial_priv->conf_data[idx]; 1345 if (value >= F81534_CONF_GPIO_SHUTDOWN) { 1346 /* 1347 * Newer IC configure will make transceiver in shutdown mode on 1348 * initial power on. We need enable it before using UARTs. 1349 */ 1350 idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num; 1351 value = serial_priv->conf_data[idx]; 1352 if (value >= F81534_CONF_GPIO_SHUTDOWN) 1353 value = F81534_CONF_GPIO_RS232; 1354 } 1355 1356 pins = &f81534_port_out_pins[port_priv->phy_num]; 1357 1358 for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) { 1359 status = f81534_set_mask_register(serial, 1360 pins->pin[i].reg_addr, pins->pin[i].reg_mask, 1361 value & BIT(i) ? pins->pin[i].reg_mask : 0); 1362 if (status) 1363 return status; 1364 } 1365 1366 dev_dbg(&port->dev, "Output pin (M0/M1/M2): %d\n", value); 1367 return 0; 1368 } 1369 1370 static int f81534_port_probe(struct usb_serial_port *port) 1371 { 1372 struct f81534_serial_private *serial_priv; 1373 struct f81534_port_private *port_priv; 1374 int ret; 1375 u8 value; 1376 1377 serial_priv = usb_get_serial_data(port->serial); 1378 port_priv = devm_kzalloc(&port->dev, sizeof(*port_priv), GFP_KERNEL); 1379 if (!port_priv) 1380 return -ENOMEM; 1381 1382 /* 1383 * We'll make tx frame error when baud rate from 384~500kps. So we'll 1384 * delay all tx data frame with 1bit. 1385 */ 1386 port_priv->shadow_clk = F81534_UART_EN | F81534_CLK_TX_DELAY_1BIT; 1387 spin_lock_init(&port_priv->msr_lock); 1388 mutex_init(&port_priv->mcr_mutex); 1389 mutex_init(&port_priv->lcr_mutex); 1390 INIT_WORK(&port_priv->lsr_work, f81534_lsr_worker); 1391 1392 /* Assign logic-to-phy mapping */ 1393 ret = f81534_logic_to_phy_port(port->serial, port); 1394 if (ret < 0) 1395 return ret; 1396 1397 port_priv->phy_num = ret; 1398 port_priv->port = port; 1399 usb_set_serial_port_data(port, port_priv); 1400 dev_dbg(&port->dev, "%s: port_number: %d, phy_num: %d\n", __func__, 1401 port->port_number, port_priv->phy_num); 1402 1403 /* 1404 * The F81532/534 will hang-up when enable LSR interrupt in IER and 1405 * occur data overrun. So we'll disable the LSR interrupt in probe() 1406 * and submit the LSR worker to clear LSR state when reported LSR error 1407 * bit with bulk-in data in f81534_process_per_serial_block(). 1408 */ 1409 ret = f81534_set_port_register(port, F81534_INTERRUPT_ENABLE_REG, 1410 UART_IER_RDI | UART_IER_THRI | UART_IER_MSI); 1411 if (ret) 1412 return ret; 1413 1414 value = serial_priv->conf_data[port_priv->phy_num]; 1415 switch (value & F81534_PORT_CONF_MODE_MASK) { 1416 case F81534_PORT_CONF_RS485_INVERT: 1417 port_priv->shadow_clk |= F81534_CLK_RS485_MODE | 1418 F81534_CLK_RS485_INVERT; 1419 dev_dbg(&port->dev, "RS485 invert mode\n"); 1420 break; 1421 case F81534_PORT_CONF_RS485: 1422 port_priv->shadow_clk |= F81534_CLK_RS485_MODE; 1423 dev_dbg(&port->dev, "RS485 mode\n"); 1424 break; 1425 1426 default: 1427 case F81534_PORT_CONF_RS232: 1428 dev_dbg(&port->dev, "RS232 mode\n"); 1429 break; 1430 } 1431 1432 return f81534_set_port_output_pin(port); 1433 } 1434 1435 static int f81534_port_remove(struct usb_serial_port *port) 1436 { 1437 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1438 1439 flush_work(&port_priv->lsr_work); 1440 return 0; 1441 } 1442 1443 static int f81534_tiocmget(struct tty_struct *tty) 1444 { 1445 struct usb_serial_port *port = tty->driver_data; 1446 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1447 int status; 1448 int r; 1449 u8 msr; 1450 u8 mcr; 1451 1452 /* Read current MSR from device */ 1453 status = f81534_get_port_register(port, F81534_MODEM_STATUS_REG, &msr); 1454 if (status) 1455 return status; 1456 1457 mutex_lock(&port_priv->mcr_mutex); 1458 mcr = port_priv->shadow_mcr; 1459 mutex_unlock(&port_priv->mcr_mutex); 1460 1461 r = (mcr & UART_MCR_DTR ? TIOCM_DTR : 0) | 1462 (mcr & UART_MCR_RTS ? TIOCM_RTS : 0) | 1463 (msr & UART_MSR_CTS ? TIOCM_CTS : 0) | 1464 (msr & UART_MSR_DCD ? TIOCM_CAR : 0) | 1465 (msr & UART_MSR_RI ? TIOCM_RI : 0) | 1466 (msr & UART_MSR_DSR ? TIOCM_DSR : 0); 1467 1468 return r; 1469 } 1470 1471 static int f81534_tiocmset(struct tty_struct *tty, unsigned int set, 1472 unsigned int clear) 1473 { 1474 struct usb_serial_port *port = tty->driver_data; 1475 1476 return f81534_update_mctrl(port, set, clear); 1477 } 1478 1479 static void f81534_dtr_rts(struct usb_serial_port *port, int on) 1480 { 1481 if (on) 1482 f81534_update_mctrl(port, TIOCM_DTR | TIOCM_RTS, 0); 1483 else 1484 f81534_update_mctrl(port, 0, TIOCM_DTR | TIOCM_RTS); 1485 } 1486 1487 static int f81534_write(struct tty_struct *tty, struct usb_serial_port *port, 1488 const u8 *buf, int count) 1489 { 1490 int bytes_out, status; 1491 1492 if (!count) 1493 return 0; 1494 1495 bytes_out = kfifo_in_locked(&port->write_fifo, buf, count, 1496 &port->lock); 1497 1498 status = f81534_submit_writer(port, GFP_ATOMIC); 1499 if (status) { 1500 dev_err(&port->dev, "%s: submit failed\n", __func__); 1501 return status; 1502 } 1503 1504 return bytes_out; 1505 } 1506 1507 static bool f81534_tx_empty(struct usb_serial_port *port) 1508 { 1509 struct f81534_port_private *port_priv = usb_get_serial_port_data(port); 1510 1511 return test_bit(F81534_TX_EMPTY_BIT, &port_priv->tx_empty); 1512 } 1513 1514 static int f81534_resume(struct usb_serial *serial) 1515 { 1516 struct f81534_serial_private *serial_priv = 1517 usb_get_serial_data(serial); 1518 struct usb_serial_port *port; 1519 int error = 0; 1520 int status; 1521 size_t i; 1522 1523 /* 1524 * We'll register port 0 bulkin when port had opened, It'll take all 1525 * port received data, MSR register change and TX_EMPTY information. 1526 */ 1527 mutex_lock(&serial_priv->urb_mutex); 1528 1529 if (serial_priv->opened_port) { 1530 status = f81534_submit_read_urb(serial, GFP_NOIO); 1531 if (status) { 1532 mutex_unlock(&serial_priv->urb_mutex); 1533 return status; 1534 } 1535 } 1536 1537 mutex_unlock(&serial_priv->urb_mutex); 1538 1539 for (i = 0; i < serial->num_ports; i++) { 1540 port = serial->port[i]; 1541 if (!tty_port_initialized(&port->port)) 1542 continue; 1543 1544 status = f81534_submit_writer(port, GFP_NOIO); 1545 if (status) { 1546 dev_err(&port->dev, "%s: submit failed\n", __func__); 1547 ++error; 1548 } 1549 } 1550 1551 if (error) 1552 return -EIO; 1553 1554 return 0; 1555 } 1556 1557 static struct usb_serial_driver f81534_device = { 1558 .driver = { 1559 .owner = THIS_MODULE, 1560 .name = "f81534", 1561 }, 1562 .description = DRIVER_DESC, 1563 .id_table = f81534_id_table, 1564 .num_bulk_in = 1, 1565 .num_bulk_out = 1, 1566 .open = f81534_open, 1567 .close = f81534_close, 1568 .write = f81534_write, 1569 .tx_empty = f81534_tx_empty, 1570 .calc_num_ports = f81534_calc_num_ports, 1571 .port_probe = f81534_port_probe, 1572 .port_remove = f81534_port_remove, 1573 .break_ctl = f81534_break_ctl, 1574 .dtr_rts = f81534_dtr_rts, 1575 .process_read_urb = f81534_process_read_urb, 1576 .get_serial = f81534_get_serial_info, 1577 .tiocmget = f81534_tiocmget, 1578 .tiocmset = f81534_tiocmset, 1579 .write_bulk_callback = f81534_write_usb_callback, 1580 .set_termios = f81534_set_termios, 1581 .resume = f81534_resume, 1582 }; 1583 1584 static struct usb_serial_driver *const serial_drivers[] = { 1585 &f81534_device, NULL 1586 }; 1587 1588 module_usb_serial_driver(serial_drivers, f81534_id_table); 1589 1590 MODULE_DEVICE_TABLE(usb, f81534_id_table); 1591 MODULE_DESCRIPTION(DRIVER_DESC); 1592 MODULE_AUTHOR("Peter Hong <Peter_Hong@fintek.com.tw>"); 1593 MODULE_AUTHOR("Tom Tsai <Tom_Tsai@fintek.com.tw>"); 1594 MODULE_LICENSE("GPL"); 1595