1 /* 2 * Digi AccelePort USB-4 and USB-2 Serial Converters 3 * 4 * Copyright 2000 by Digi International 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License as published by 8 * the Free Software Foundation; either version 2 of the License, or 9 * (at your option) any later version. 10 * 11 * Shamelessly based on Brian Warner's keyspan_pda.c and Greg Kroah-Hartman's 12 * usb-serial driver. 13 * 14 * Peter Berger (pberger@brimson.com) 15 * Al Borchers (borchers@steinerpoint.com) 16 */ 17 18 #include <linux/kernel.h> 19 #include <linux/errno.h> 20 #include <linux/slab.h> 21 #include <linux/tty.h> 22 #include <linux/tty_driver.h> 23 #include <linux/tty_flip.h> 24 #include <linux/module.h> 25 #include <linux/spinlock.h> 26 #include <linux/workqueue.h> 27 #include <linux/uaccess.h> 28 #include <linux/usb.h> 29 #include <linux/wait.h> 30 #include <linux/usb/serial.h> 31 32 /* Defines */ 33 34 #define DRIVER_AUTHOR "Peter Berger <pberger@brimson.com>, Al Borchers <borchers@steinerpoint.com>" 35 #define DRIVER_DESC "Digi AccelePort USB-2/USB-4 Serial Converter driver" 36 37 /* port output buffer length -- must be <= transfer buffer length - 2 */ 38 /* so we can be sure to send the full buffer in one urb */ 39 #define DIGI_OUT_BUF_SIZE 8 40 41 /* port input buffer length -- must be >= transfer buffer length - 3 */ 42 /* so we can be sure to hold at least one full buffer from one urb */ 43 #define DIGI_IN_BUF_SIZE 64 44 45 /* retry timeout while sleeping */ 46 #define DIGI_RETRY_TIMEOUT (HZ/10) 47 48 /* timeout while waiting for tty output to drain in close */ 49 /* this delay is used twice in close, so the total delay could */ 50 /* be twice this value */ 51 #define DIGI_CLOSE_TIMEOUT (5*HZ) 52 53 54 /* AccelePort USB Defines */ 55 56 /* ids */ 57 #define DIGI_VENDOR_ID 0x05c5 58 #define DIGI_2_ID 0x0002 /* USB-2 */ 59 #define DIGI_4_ID 0x0004 /* USB-4 */ 60 61 /* commands 62 * "INB": can be used on the in-band endpoint 63 * "OOB": can be used on the out-of-band endpoint 64 */ 65 #define DIGI_CMD_SET_BAUD_RATE 0 /* INB, OOB */ 66 #define DIGI_CMD_SET_WORD_SIZE 1 /* INB, OOB */ 67 #define DIGI_CMD_SET_PARITY 2 /* INB, OOB */ 68 #define DIGI_CMD_SET_STOP_BITS 3 /* INB, OOB */ 69 #define DIGI_CMD_SET_INPUT_FLOW_CONTROL 4 /* INB, OOB */ 70 #define DIGI_CMD_SET_OUTPUT_FLOW_CONTROL 5 /* INB, OOB */ 71 #define DIGI_CMD_SET_DTR_SIGNAL 6 /* INB, OOB */ 72 #define DIGI_CMD_SET_RTS_SIGNAL 7 /* INB, OOB */ 73 #define DIGI_CMD_READ_INPUT_SIGNALS 8 /* OOB */ 74 #define DIGI_CMD_IFLUSH_FIFO 9 /* OOB */ 75 #define DIGI_CMD_RECEIVE_ENABLE 10 /* INB, OOB */ 76 #define DIGI_CMD_BREAK_CONTROL 11 /* INB, OOB */ 77 #define DIGI_CMD_LOCAL_LOOPBACK 12 /* INB, OOB */ 78 #define DIGI_CMD_TRANSMIT_IDLE 13 /* INB, OOB */ 79 #define DIGI_CMD_READ_UART_REGISTER 14 /* OOB */ 80 #define DIGI_CMD_WRITE_UART_REGISTER 15 /* INB, OOB */ 81 #define DIGI_CMD_AND_UART_REGISTER 16 /* INB, OOB */ 82 #define DIGI_CMD_OR_UART_REGISTER 17 /* INB, OOB */ 83 #define DIGI_CMD_SEND_DATA 18 /* INB */ 84 #define DIGI_CMD_RECEIVE_DATA 19 /* INB */ 85 #define DIGI_CMD_RECEIVE_DISABLE 20 /* INB */ 86 #define DIGI_CMD_GET_PORT_TYPE 21 /* OOB */ 87 88 /* baud rates */ 89 #define DIGI_BAUD_50 0 90 #define DIGI_BAUD_75 1 91 #define DIGI_BAUD_110 2 92 #define DIGI_BAUD_150 3 93 #define DIGI_BAUD_200 4 94 #define DIGI_BAUD_300 5 95 #define DIGI_BAUD_600 6 96 #define DIGI_BAUD_1200 7 97 #define DIGI_BAUD_1800 8 98 #define DIGI_BAUD_2400 9 99 #define DIGI_BAUD_4800 10 100 #define DIGI_BAUD_7200 11 101 #define DIGI_BAUD_9600 12 102 #define DIGI_BAUD_14400 13 103 #define DIGI_BAUD_19200 14 104 #define DIGI_BAUD_28800 15 105 #define DIGI_BAUD_38400 16 106 #define DIGI_BAUD_57600 17 107 #define DIGI_BAUD_76800 18 108 #define DIGI_BAUD_115200 19 109 #define DIGI_BAUD_153600 20 110 #define DIGI_BAUD_230400 21 111 #define DIGI_BAUD_460800 22 112 113 /* arguments */ 114 #define DIGI_WORD_SIZE_5 0 115 #define DIGI_WORD_SIZE_6 1 116 #define DIGI_WORD_SIZE_7 2 117 #define DIGI_WORD_SIZE_8 3 118 119 #define DIGI_PARITY_NONE 0 120 #define DIGI_PARITY_ODD 1 121 #define DIGI_PARITY_EVEN 2 122 #define DIGI_PARITY_MARK 3 123 #define DIGI_PARITY_SPACE 4 124 125 #define DIGI_STOP_BITS_1 0 126 #define DIGI_STOP_BITS_2 1 127 128 #define DIGI_INPUT_FLOW_CONTROL_XON_XOFF 1 129 #define DIGI_INPUT_FLOW_CONTROL_RTS 2 130 #define DIGI_INPUT_FLOW_CONTROL_DTR 4 131 132 #define DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF 1 133 #define DIGI_OUTPUT_FLOW_CONTROL_CTS 2 134 #define DIGI_OUTPUT_FLOW_CONTROL_DSR 4 135 136 #define DIGI_DTR_INACTIVE 0 137 #define DIGI_DTR_ACTIVE 1 138 #define DIGI_DTR_INPUT_FLOW_CONTROL 2 139 140 #define DIGI_RTS_INACTIVE 0 141 #define DIGI_RTS_ACTIVE 1 142 #define DIGI_RTS_INPUT_FLOW_CONTROL 2 143 #define DIGI_RTS_TOGGLE 3 144 145 #define DIGI_FLUSH_TX 1 146 #define DIGI_FLUSH_RX 2 147 #define DIGI_RESUME_TX 4 /* clears xoff condition */ 148 149 #define DIGI_TRANSMIT_NOT_IDLE 0 150 #define DIGI_TRANSMIT_IDLE 1 151 152 #define DIGI_DISABLE 0 153 #define DIGI_ENABLE 1 154 155 #define DIGI_DEASSERT 0 156 #define DIGI_ASSERT 1 157 158 /* in band status codes */ 159 #define DIGI_OVERRUN_ERROR 4 160 #define DIGI_PARITY_ERROR 8 161 #define DIGI_FRAMING_ERROR 16 162 #define DIGI_BREAK_ERROR 32 163 164 /* out of band status */ 165 #define DIGI_NO_ERROR 0 166 #define DIGI_BAD_FIRST_PARAMETER 1 167 #define DIGI_BAD_SECOND_PARAMETER 2 168 #define DIGI_INVALID_LINE 3 169 #define DIGI_INVALID_OPCODE 4 170 171 /* input signals */ 172 #define DIGI_READ_INPUT_SIGNALS_SLOT 1 173 #define DIGI_READ_INPUT_SIGNALS_ERR 2 174 #define DIGI_READ_INPUT_SIGNALS_BUSY 4 175 #define DIGI_READ_INPUT_SIGNALS_PE 8 176 #define DIGI_READ_INPUT_SIGNALS_CTS 16 177 #define DIGI_READ_INPUT_SIGNALS_DSR 32 178 #define DIGI_READ_INPUT_SIGNALS_RI 64 179 #define DIGI_READ_INPUT_SIGNALS_DCD 128 180 181 182 /* Structures */ 183 184 struct digi_serial { 185 spinlock_t ds_serial_lock; 186 struct usb_serial_port *ds_oob_port; /* out-of-band port */ 187 int ds_oob_port_num; /* index of out-of-band port */ 188 int ds_device_started; 189 }; 190 191 struct digi_port { 192 spinlock_t dp_port_lock; 193 int dp_port_num; 194 int dp_out_buf_len; 195 unsigned char dp_out_buf[DIGI_OUT_BUF_SIZE]; 196 int dp_write_urb_in_use; 197 unsigned int dp_modem_signals; 198 int dp_transmit_idle; 199 wait_queue_head_t dp_transmit_idle_wait; 200 int dp_throttled; 201 int dp_throttle_restart; 202 wait_queue_head_t dp_flush_wait; 203 wait_queue_head_t dp_close_wait; /* wait queue for close */ 204 struct work_struct dp_wakeup_work; 205 struct usb_serial_port *dp_port; 206 }; 207 208 209 /* Local Function Declarations */ 210 211 static void digi_wakeup_write_lock(struct work_struct *work); 212 static int digi_write_oob_command(struct usb_serial_port *port, 213 unsigned char *buf, int count, int interruptible); 214 static int digi_write_inb_command(struct usb_serial_port *port, 215 unsigned char *buf, int count, unsigned long timeout); 216 static int digi_set_modem_signals(struct usb_serial_port *port, 217 unsigned int modem_signals, int interruptible); 218 static int digi_transmit_idle(struct usb_serial_port *port, 219 unsigned long timeout); 220 static void digi_rx_throttle(struct tty_struct *tty); 221 static void digi_rx_unthrottle(struct tty_struct *tty); 222 static void digi_set_termios(struct tty_struct *tty, 223 struct usb_serial_port *port, struct ktermios *old_termios); 224 static void digi_break_ctl(struct tty_struct *tty, int break_state); 225 static int digi_tiocmget(struct tty_struct *tty); 226 static int digi_tiocmset(struct tty_struct *tty, unsigned int set, 227 unsigned int clear); 228 static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, 229 const unsigned char *buf, int count); 230 static void digi_write_bulk_callback(struct urb *urb); 231 static int digi_write_room(struct tty_struct *tty); 232 static int digi_chars_in_buffer(struct tty_struct *tty); 233 static int digi_open(struct tty_struct *tty, struct usb_serial_port *port); 234 static void digi_close(struct usb_serial_port *port); 235 static void digi_dtr_rts(struct usb_serial_port *port, int on); 236 static int digi_startup_device(struct usb_serial *serial); 237 static int digi_startup(struct usb_serial *serial); 238 static void digi_disconnect(struct usb_serial *serial); 239 static void digi_release(struct usb_serial *serial); 240 static int digi_port_probe(struct usb_serial_port *port); 241 static int digi_port_remove(struct usb_serial_port *port); 242 static void digi_read_bulk_callback(struct urb *urb); 243 static int digi_read_inb_callback(struct urb *urb); 244 static int digi_read_oob_callback(struct urb *urb); 245 246 247 static const struct usb_device_id id_table_combined[] = { 248 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 249 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 250 { } /* Terminating entry */ 251 }; 252 253 static const struct usb_device_id id_table_2[] = { 254 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_2_ID) }, 255 { } /* Terminating entry */ 256 }; 257 258 static const struct usb_device_id id_table_4[] = { 259 { USB_DEVICE(DIGI_VENDOR_ID, DIGI_4_ID) }, 260 { } /* Terminating entry */ 261 }; 262 263 MODULE_DEVICE_TABLE(usb, id_table_combined); 264 265 /* device info needed for the Digi serial converter */ 266 267 static struct usb_serial_driver digi_acceleport_2_device = { 268 .driver = { 269 .owner = THIS_MODULE, 270 .name = "digi_2", 271 }, 272 .description = "Digi 2 port USB adapter", 273 .id_table = id_table_2, 274 .num_ports = 3, 275 .open = digi_open, 276 .close = digi_close, 277 .dtr_rts = digi_dtr_rts, 278 .write = digi_write, 279 .write_room = digi_write_room, 280 .write_bulk_callback = digi_write_bulk_callback, 281 .read_bulk_callback = digi_read_bulk_callback, 282 .chars_in_buffer = digi_chars_in_buffer, 283 .throttle = digi_rx_throttle, 284 .unthrottle = digi_rx_unthrottle, 285 .set_termios = digi_set_termios, 286 .break_ctl = digi_break_ctl, 287 .tiocmget = digi_tiocmget, 288 .tiocmset = digi_tiocmset, 289 .attach = digi_startup, 290 .disconnect = digi_disconnect, 291 .release = digi_release, 292 .port_probe = digi_port_probe, 293 .port_remove = digi_port_remove, 294 }; 295 296 static struct usb_serial_driver digi_acceleport_4_device = { 297 .driver = { 298 .owner = THIS_MODULE, 299 .name = "digi_4", 300 }, 301 .description = "Digi 4 port USB adapter", 302 .id_table = id_table_4, 303 .num_ports = 4, 304 .open = digi_open, 305 .close = digi_close, 306 .write = digi_write, 307 .write_room = digi_write_room, 308 .write_bulk_callback = digi_write_bulk_callback, 309 .read_bulk_callback = digi_read_bulk_callback, 310 .chars_in_buffer = digi_chars_in_buffer, 311 .throttle = digi_rx_throttle, 312 .unthrottle = digi_rx_unthrottle, 313 .set_termios = digi_set_termios, 314 .break_ctl = digi_break_ctl, 315 .tiocmget = digi_tiocmget, 316 .tiocmset = digi_tiocmset, 317 .attach = digi_startup, 318 .disconnect = digi_disconnect, 319 .release = digi_release, 320 .port_probe = digi_port_probe, 321 .port_remove = digi_port_remove, 322 }; 323 324 static struct usb_serial_driver * const serial_drivers[] = { 325 &digi_acceleport_2_device, &digi_acceleport_4_device, NULL 326 }; 327 328 /* Functions */ 329 330 /* 331 * Cond Wait Interruptible Timeout Irqrestore 332 * 333 * Do spin_unlock_irqrestore and interruptible_sleep_on_timeout 334 * so that wake ups are not lost if they occur between the unlock 335 * and the sleep. In other words, spin_unlock_irqrestore and 336 * interruptible_sleep_on_timeout are "atomic" with respect to 337 * wake ups. This is used to implement condition variables. 338 * 339 * interruptible_sleep_on_timeout is deprecated and has been replaced 340 * with the equivalent code. 341 */ 342 343 static long cond_wait_interruptible_timeout_irqrestore( 344 wait_queue_head_t *q, long timeout, 345 spinlock_t *lock, unsigned long flags) 346 __releases(lock) 347 { 348 DEFINE_WAIT(wait); 349 350 prepare_to_wait(q, &wait, TASK_INTERRUPTIBLE); 351 spin_unlock_irqrestore(lock, flags); 352 timeout = schedule_timeout(timeout); 353 finish_wait(q, &wait); 354 355 return timeout; 356 } 357 358 359 /* 360 * Digi Wakeup Write 361 * 362 * Wake up port, line discipline, and tty processes sleeping 363 * on writes. 364 */ 365 366 static void digi_wakeup_write_lock(struct work_struct *work) 367 { 368 struct digi_port *priv = 369 container_of(work, struct digi_port, dp_wakeup_work); 370 struct usb_serial_port *port = priv->dp_port; 371 unsigned long flags; 372 373 spin_lock_irqsave(&priv->dp_port_lock, flags); 374 tty_port_tty_wakeup(&port->port); 375 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 376 } 377 378 /* 379 * Digi Write OOB Command 380 * 381 * Write commands on the out of band port. Commands are 4 382 * bytes each, multiple commands can be sent at once, and 383 * no command will be split across USB packets. Returns 0 384 * if successful, -EINTR if interrupted while sleeping and 385 * the interruptible flag is true, or a negative error 386 * returned by usb_submit_urb. 387 */ 388 389 static int digi_write_oob_command(struct usb_serial_port *port, 390 unsigned char *buf, int count, int interruptible) 391 { 392 int ret = 0; 393 int len; 394 struct usb_serial_port *oob_port = (struct usb_serial_port *)((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 395 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 396 unsigned long flags = 0; 397 398 dev_dbg(&port->dev, 399 "digi_write_oob_command: TOP: port=%d, count=%d\n", 400 oob_priv->dp_port_num, count); 401 402 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 403 while (count > 0) { 404 while (oob_priv->dp_write_urb_in_use) { 405 cond_wait_interruptible_timeout_irqrestore( 406 &oob_port->write_wait, DIGI_RETRY_TIMEOUT, 407 &oob_priv->dp_port_lock, flags); 408 if (interruptible && signal_pending(current)) 409 return -EINTR; 410 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 411 } 412 413 /* len must be a multiple of 4, so commands are not split */ 414 len = min(count, oob_port->bulk_out_size); 415 if (len > 4) 416 len &= ~3; 417 memcpy(oob_port->write_urb->transfer_buffer, buf, len); 418 oob_port->write_urb->transfer_buffer_length = len; 419 ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); 420 if (ret == 0) { 421 oob_priv->dp_write_urb_in_use = 1; 422 count -= len; 423 buf += len; 424 } 425 } 426 spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); 427 if (ret) 428 dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", 429 __func__, ret); 430 return ret; 431 432 } 433 434 435 /* 436 * Digi Write In Band Command 437 * 438 * Write commands on the given port. Commands are 4 439 * bytes each, multiple commands can be sent at once, and 440 * no command will be split across USB packets. If timeout 441 * is non-zero, write in band command will return after 442 * waiting unsuccessfully for the URB status to clear for 443 * timeout ticks. Returns 0 if successful, or a negative 444 * error returned by digi_write. 445 */ 446 447 static int digi_write_inb_command(struct usb_serial_port *port, 448 unsigned char *buf, int count, unsigned long timeout) 449 { 450 int ret = 0; 451 int len; 452 struct digi_port *priv = usb_get_serial_port_data(port); 453 unsigned char *data = port->write_urb->transfer_buffer; 454 unsigned long flags = 0; 455 456 dev_dbg(&port->dev, "digi_write_inb_command: TOP: port=%d, count=%d\n", 457 priv->dp_port_num, count); 458 459 if (timeout) 460 timeout += jiffies; 461 else 462 timeout = ULONG_MAX; 463 464 spin_lock_irqsave(&priv->dp_port_lock, flags); 465 while (count > 0 && ret == 0) { 466 while (priv->dp_write_urb_in_use && 467 time_before(jiffies, timeout)) { 468 cond_wait_interruptible_timeout_irqrestore( 469 &port->write_wait, DIGI_RETRY_TIMEOUT, 470 &priv->dp_port_lock, flags); 471 if (signal_pending(current)) 472 return -EINTR; 473 spin_lock_irqsave(&priv->dp_port_lock, flags); 474 } 475 476 /* len must be a multiple of 4 and small enough to */ 477 /* guarantee the write will send buffered data first, */ 478 /* so commands are in order with data and not split */ 479 len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 480 if (len > 4) 481 len &= ~3; 482 483 /* write any buffered data first */ 484 if (priv->dp_out_buf_len > 0) { 485 data[0] = DIGI_CMD_SEND_DATA; 486 data[1] = priv->dp_out_buf_len; 487 memcpy(data + 2, priv->dp_out_buf, 488 priv->dp_out_buf_len); 489 memcpy(data + 2 + priv->dp_out_buf_len, buf, len); 490 port->write_urb->transfer_buffer_length 491 = priv->dp_out_buf_len + 2 + len; 492 } else { 493 memcpy(data, buf, len); 494 port->write_urb->transfer_buffer_length = len; 495 } 496 497 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 498 if (ret == 0) { 499 priv->dp_write_urb_in_use = 1; 500 priv->dp_out_buf_len = 0; 501 count -= len; 502 buf += len; 503 } 504 505 } 506 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 507 508 if (ret) 509 dev_err(&port->dev, 510 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 511 __func__, ret, priv->dp_port_num); 512 return ret; 513 } 514 515 516 /* 517 * Digi Set Modem Signals 518 * 519 * Sets or clears DTR and RTS on the port, according to the 520 * modem_signals argument. Use TIOCM_DTR and TIOCM_RTS flags 521 * for the modem_signals argument. Returns 0 if successful, 522 * -EINTR if interrupted while sleeping, or a non-zero error 523 * returned by usb_submit_urb. 524 */ 525 526 static int digi_set_modem_signals(struct usb_serial_port *port, 527 unsigned int modem_signals, int interruptible) 528 { 529 530 int ret; 531 struct digi_port *port_priv = usb_get_serial_port_data(port); 532 struct usb_serial_port *oob_port = (struct usb_serial_port *) ((struct digi_serial *)(usb_get_serial_data(port->serial)))->ds_oob_port; 533 struct digi_port *oob_priv = usb_get_serial_port_data(oob_port); 534 unsigned char *data = oob_port->write_urb->transfer_buffer; 535 unsigned long flags = 0; 536 537 538 dev_dbg(&port->dev, 539 "digi_set_modem_signals: TOP: port=%d, modem_signals=0x%x\n", 540 port_priv->dp_port_num, modem_signals); 541 542 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 543 spin_lock(&port_priv->dp_port_lock); 544 545 while (oob_priv->dp_write_urb_in_use) { 546 spin_unlock(&port_priv->dp_port_lock); 547 cond_wait_interruptible_timeout_irqrestore( 548 &oob_port->write_wait, DIGI_RETRY_TIMEOUT, 549 &oob_priv->dp_port_lock, flags); 550 if (interruptible && signal_pending(current)) 551 return -EINTR; 552 spin_lock_irqsave(&oob_priv->dp_port_lock, flags); 553 spin_lock(&port_priv->dp_port_lock); 554 } 555 data[0] = DIGI_CMD_SET_DTR_SIGNAL; 556 data[1] = port_priv->dp_port_num; 557 data[2] = (modem_signals & TIOCM_DTR) ? 558 DIGI_DTR_ACTIVE : DIGI_DTR_INACTIVE; 559 data[3] = 0; 560 data[4] = DIGI_CMD_SET_RTS_SIGNAL; 561 data[5] = port_priv->dp_port_num; 562 data[6] = (modem_signals & TIOCM_RTS) ? 563 DIGI_RTS_ACTIVE : DIGI_RTS_INACTIVE; 564 data[7] = 0; 565 566 oob_port->write_urb->transfer_buffer_length = 8; 567 568 ret = usb_submit_urb(oob_port->write_urb, GFP_ATOMIC); 569 if (ret == 0) { 570 oob_priv->dp_write_urb_in_use = 1; 571 port_priv->dp_modem_signals = 572 (port_priv->dp_modem_signals&~(TIOCM_DTR|TIOCM_RTS)) 573 | (modem_signals&(TIOCM_DTR|TIOCM_RTS)); 574 } 575 spin_unlock(&port_priv->dp_port_lock); 576 spin_unlock_irqrestore(&oob_priv->dp_port_lock, flags); 577 if (ret) 578 dev_err(&port->dev, "%s: usb_submit_urb failed, ret=%d\n", 579 __func__, ret); 580 return ret; 581 } 582 583 /* 584 * Digi Transmit Idle 585 * 586 * Digi transmit idle waits, up to timeout ticks, for the transmitter 587 * to go idle. It returns 0 if successful or a negative error. 588 * 589 * There are race conditions here if more than one process is calling 590 * digi_transmit_idle on the same port at the same time. However, this 591 * is only called from close, and only one process can be in close on a 592 * port at a time, so its ok. 593 */ 594 595 static int digi_transmit_idle(struct usb_serial_port *port, 596 unsigned long timeout) 597 { 598 int ret; 599 unsigned char buf[2]; 600 struct digi_port *priv = usb_get_serial_port_data(port); 601 unsigned long flags = 0; 602 603 spin_lock_irqsave(&priv->dp_port_lock, flags); 604 priv->dp_transmit_idle = 0; 605 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 606 607 buf[0] = DIGI_CMD_TRANSMIT_IDLE; 608 buf[1] = 0; 609 610 timeout += jiffies; 611 612 ret = digi_write_inb_command(port, buf, 2, timeout - jiffies); 613 if (ret != 0) 614 return ret; 615 616 spin_lock_irqsave(&priv->dp_port_lock, flags); 617 618 while (time_before(jiffies, timeout) && !priv->dp_transmit_idle) { 619 cond_wait_interruptible_timeout_irqrestore( 620 &priv->dp_transmit_idle_wait, DIGI_RETRY_TIMEOUT, 621 &priv->dp_port_lock, flags); 622 if (signal_pending(current)) 623 return -EINTR; 624 spin_lock_irqsave(&priv->dp_port_lock, flags); 625 } 626 priv->dp_transmit_idle = 0; 627 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 628 return 0; 629 630 } 631 632 633 static void digi_rx_throttle(struct tty_struct *tty) 634 { 635 unsigned long flags; 636 struct usb_serial_port *port = tty->driver_data; 637 struct digi_port *priv = usb_get_serial_port_data(port); 638 639 /* stop receiving characters by not resubmitting the read urb */ 640 spin_lock_irqsave(&priv->dp_port_lock, flags); 641 priv->dp_throttled = 1; 642 priv->dp_throttle_restart = 0; 643 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 644 } 645 646 647 static void digi_rx_unthrottle(struct tty_struct *tty) 648 { 649 int ret = 0; 650 unsigned long flags; 651 struct usb_serial_port *port = tty->driver_data; 652 struct digi_port *priv = usb_get_serial_port_data(port); 653 654 spin_lock_irqsave(&priv->dp_port_lock, flags); 655 656 /* restart read chain */ 657 if (priv->dp_throttle_restart) 658 ret = usb_submit_urb(port->read_urb, GFP_ATOMIC); 659 660 /* turn throttle off */ 661 priv->dp_throttled = 0; 662 priv->dp_throttle_restart = 0; 663 664 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 665 666 if (ret) 667 dev_err(&port->dev, 668 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 669 __func__, ret, priv->dp_port_num); 670 } 671 672 673 static void digi_set_termios(struct tty_struct *tty, 674 struct usb_serial_port *port, struct ktermios *old_termios) 675 { 676 struct digi_port *priv = usb_get_serial_port_data(port); 677 struct device *dev = &port->dev; 678 unsigned int iflag = tty->termios.c_iflag; 679 unsigned int cflag = tty->termios.c_cflag; 680 unsigned int old_iflag = old_termios->c_iflag; 681 unsigned int old_cflag = old_termios->c_cflag; 682 unsigned char buf[32]; 683 unsigned int modem_signals; 684 int arg, ret; 685 int i = 0; 686 speed_t baud; 687 688 dev_dbg(dev, 689 "digi_set_termios: TOP: port=%d, iflag=0x%x, old_iflag=0x%x, cflag=0x%x, old_cflag=0x%x\n", 690 priv->dp_port_num, iflag, old_iflag, cflag, old_cflag); 691 692 /* set baud rate */ 693 baud = tty_get_baud_rate(tty); 694 if (baud != tty_termios_baud_rate(old_termios)) { 695 arg = -1; 696 697 /* reassert DTR and (maybe) RTS on transition from B0 */ 698 if ((old_cflag & CBAUD) == B0) { 699 /* don't set RTS if using hardware flow control */ 700 /* and throttling input */ 701 modem_signals = TIOCM_DTR; 702 if (!C_CRTSCTS(tty) || !tty_throttled(tty)) 703 modem_signals |= TIOCM_RTS; 704 digi_set_modem_signals(port, modem_signals, 1); 705 } 706 switch (baud) { 707 /* drop DTR and RTS on transition to B0 */ 708 case 0: digi_set_modem_signals(port, 0, 1); break; 709 case 50: arg = DIGI_BAUD_50; break; 710 case 75: arg = DIGI_BAUD_75; break; 711 case 110: arg = DIGI_BAUD_110; break; 712 case 150: arg = DIGI_BAUD_150; break; 713 case 200: arg = DIGI_BAUD_200; break; 714 case 300: arg = DIGI_BAUD_300; break; 715 case 600: arg = DIGI_BAUD_600; break; 716 case 1200: arg = DIGI_BAUD_1200; break; 717 case 1800: arg = DIGI_BAUD_1800; break; 718 case 2400: arg = DIGI_BAUD_2400; break; 719 case 4800: arg = DIGI_BAUD_4800; break; 720 case 9600: arg = DIGI_BAUD_9600; break; 721 case 19200: arg = DIGI_BAUD_19200; break; 722 case 38400: arg = DIGI_BAUD_38400; break; 723 case 57600: arg = DIGI_BAUD_57600; break; 724 case 115200: arg = DIGI_BAUD_115200; break; 725 case 230400: arg = DIGI_BAUD_230400; break; 726 case 460800: arg = DIGI_BAUD_460800; break; 727 default: 728 arg = DIGI_BAUD_9600; 729 baud = 9600; 730 break; 731 } 732 if (arg != -1) { 733 buf[i++] = DIGI_CMD_SET_BAUD_RATE; 734 buf[i++] = priv->dp_port_num; 735 buf[i++] = arg; 736 buf[i++] = 0; 737 } 738 } 739 /* set parity */ 740 tty->termios.c_cflag &= ~CMSPAR; 741 742 if ((cflag&(PARENB|PARODD)) != (old_cflag&(PARENB|PARODD))) { 743 if (cflag&PARENB) { 744 if (cflag&PARODD) 745 arg = DIGI_PARITY_ODD; 746 else 747 arg = DIGI_PARITY_EVEN; 748 } else { 749 arg = DIGI_PARITY_NONE; 750 } 751 buf[i++] = DIGI_CMD_SET_PARITY; 752 buf[i++] = priv->dp_port_num; 753 buf[i++] = arg; 754 buf[i++] = 0; 755 } 756 /* set word size */ 757 if ((cflag&CSIZE) != (old_cflag&CSIZE)) { 758 arg = -1; 759 switch (cflag&CSIZE) { 760 case CS5: arg = DIGI_WORD_SIZE_5; break; 761 case CS6: arg = DIGI_WORD_SIZE_6; break; 762 case CS7: arg = DIGI_WORD_SIZE_7; break; 763 case CS8: arg = DIGI_WORD_SIZE_8; break; 764 default: 765 dev_dbg(dev, 766 "digi_set_termios: can't handle word size %d\n", 767 (cflag&CSIZE)); 768 break; 769 } 770 771 if (arg != -1) { 772 buf[i++] = DIGI_CMD_SET_WORD_SIZE; 773 buf[i++] = priv->dp_port_num; 774 buf[i++] = arg; 775 buf[i++] = 0; 776 } 777 778 } 779 780 /* set stop bits */ 781 if ((cflag&CSTOPB) != (old_cflag&CSTOPB)) { 782 783 if ((cflag&CSTOPB)) 784 arg = DIGI_STOP_BITS_2; 785 else 786 arg = DIGI_STOP_BITS_1; 787 788 buf[i++] = DIGI_CMD_SET_STOP_BITS; 789 buf[i++] = priv->dp_port_num; 790 buf[i++] = arg; 791 buf[i++] = 0; 792 793 } 794 795 /* set input flow control */ 796 if ((iflag&IXOFF) != (old_iflag&IXOFF) 797 || (cflag&CRTSCTS) != (old_cflag&CRTSCTS)) { 798 arg = 0; 799 if (iflag&IXOFF) 800 arg |= DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 801 else 802 arg &= ~DIGI_INPUT_FLOW_CONTROL_XON_XOFF; 803 804 if (cflag&CRTSCTS) { 805 arg |= DIGI_INPUT_FLOW_CONTROL_RTS; 806 807 /* On USB-4 it is necessary to assert RTS prior */ 808 /* to selecting RTS input flow control. */ 809 buf[i++] = DIGI_CMD_SET_RTS_SIGNAL; 810 buf[i++] = priv->dp_port_num; 811 buf[i++] = DIGI_RTS_ACTIVE; 812 buf[i++] = 0; 813 814 } else { 815 arg &= ~DIGI_INPUT_FLOW_CONTROL_RTS; 816 } 817 buf[i++] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 818 buf[i++] = priv->dp_port_num; 819 buf[i++] = arg; 820 buf[i++] = 0; 821 } 822 823 /* set output flow control */ 824 if ((iflag & IXON) != (old_iflag & IXON) 825 || (cflag & CRTSCTS) != (old_cflag & CRTSCTS)) { 826 arg = 0; 827 if (iflag & IXON) 828 arg |= DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 829 else 830 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_XON_XOFF; 831 832 if (cflag & CRTSCTS) { 833 arg |= DIGI_OUTPUT_FLOW_CONTROL_CTS; 834 } else { 835 arg &= ~DIGI_OUTPUT_FLOW_CONTROL_CTS; 836 } 837 838 buf[i++] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 839 buf[i++] = priv->dp_port_num; 840 buf[i++] = arg; 841 buf[i++] = 0; 842 } 843 844 /* set receive enable/disable */ 845 if ((cflag & CREAD) != (old_cflag & CREAD)) { 846 if (cflag & CREAD) 847 arg = DIGI_ENABLE; 848 else 849 arg = DIGI_DISABLE; 850 851 buf[i++] = DIGI_CMD_RECEIVE_ENABLE; 852 buf[i++] = priv->dp_port_num; 853 buf[i++] = arg; 854 buf[i++] = 0; 855 } 856 ret = digi_write_oob_command(port, buf, i, 1); 857 if (ret != 0) 858 dev_dbg(dev, "digi_set_termios: write oob failed, ret=%d\n", ret); 859 tty_encode_baud_rate(tty, baud, baud); 860 } 861 862 863 static void digi_break_ctl(struct tty_struct *tty, int break_state) 864 { 865 struct usb_serial_port *port = tty->driver_data; 866 unsigned char buf[4]; 867 868 buf[0] = DIGI_CMD_BREAK_CONTROL; 869 buf[1] = 2; /* length */ 870 buf[2] = break_state ? 1 : 0; 871 buf[3] = 0; /* pad */ 872 digi_write_inb_command(port, buf, 4, 0); 873 } 874 875 876 static int digi_tiocmget(struct tty_struct *tty) 877 { 878 struct usb_serial_port *port = tty->driver_data; 879 struct digi_port *priv = usb_get_serial_port_data(port); 880 unsigned int val; 881 unsigned long flags; 882 883 spin_lock_irqsave(&priv->dp_port_lock, flags); 884 val = priv->dp_modem_signals; 885 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 886 return val; 887 } 888 889 890 static int digi_tiocmset(struct tty_struct *tty, 891 unsigned int set, unsigned int clear) 892 { 893 struct usb_serial_port *port = tty->driver_data; 894 struct digi_port *priv = usb_get_serial_port_data(port); 895 unsigned int val; 896 unsigned long flags; 897 898 spin_lock_irqsave(&priv->dp_port_lock, flags); 899 val = (priv->dp_modem_signals & ~clear) | set; 900 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 901 return digi_set_modem_signals(port, val, 1); 902 } 903 904 905 static int digi_write(struct tty_struct *tty, struct usb_serial_port *port, 906 const unsigned char *buf, int count) 907 { 908 909 int ret, data_len, new_len; 910 struct digi_port *priv = usb_get_serial_port_data(port); 911 unsigned char *data = port->write_urb->transfer_buffer; 912 unsigned long flags = 0; 913 914 dev_dbg(&port->dev, 915 "digi_write: TOP: port=%d, count=%d, in_interrupt=%ld\n", 916 priv->dp_port_num, count, in_interrupt()); 917 918 /* copy user data (which can sleep) before getting spin lock */ 919 count = min(count, port->bulk_out_size-2); 920 count = min(64, count); 921 922 /* be sure only one write proceeds at a time */ 923 /* there are races on the port private buffer */ 924 spin_lock_irqsave(&priv->dp_port_lock, flags); 925 926 /* wait for urb status clear to submit another urb */ 927 if (priv->dp_write_urb_in_use) { 928 /* buffer data if count is 1 (probably put_char) if possible */ 929 if (count == 1 && priv->dp_out_buf_len < DIGI_OUT_BUF_SIZE) { 930 priv->dp_out_buf[priv->dp_out_buf_len++] = *buf; 931 new_len = 1; 932 } else { 933 new_len = 0; 934 } 935 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 936 return new_len; 937 } 938 939 /* allow space for any buffered data and for new data, up to */ 940 /* transfer buffer size - 2 (for command and length bytes) */ 941 new_len = min(count, port->bulk_out_size-2-priv->dp_out_buf_len); 942 data_len = new_len + priv->dp_out_buf_len; 943 944 if (data_len == 0) { 945 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 946 return 0; 947 } 948 949 port->write_urb->transfer_buffer_length = data_len+2; 950 951 *data++ = DIGI_CMD_SEND_DATA; 952 *data++ = data_len; 953 954 /* copy in buffered data first */ 955 memcpy(data, priv->dp_out_buf, priv->dp_out_buf_len); 956 data += priv->dp_out_buf_len; 957 958 /* copy in new data */ 959 memcpy(data, buf, new_len); 960 961 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 962 if (ret == 0) { 963 priv->dp_write_urb_in_use = 1; 964 ret = new_len; 965 priv->dp_out_buf_len = 0; 966 } 967 968 /* return length of new data written, or error */ 969 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 970 if (ret < 0) 971 dev_err_console(port, 972 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 973 __func__, ret, priv->dp_port_num); 974 dev_dbg(&port->dev, "digi_write: returning %d\n", ret); 975 return ret; 976 977 } 978 979 static void digi_write_bulk_callback(struct urb *urb) 980 { 981 982 struct usb_serial_port *port = urb->context; 983 struct usb_serial *serial; 984 struct digi_port *priv; 985 struct digi_serial *serial_priv; 986 int ret = 0; 987 int status = urb->status; 988 989 /* port and serial sanity check */ 990 if (port == NULL || (priv = usb_get_serial_port_data(port)) == NULL) { 991 pr_err("%s: port or port->private is NULL, status=%d\n", 992 __func__, status); 993 return; 994 } 995 serial = port->serial; 996 if (serial == NULL || (serial_priv = usb_get_serial_data(serial)) == NULL) { 997 dev_err(&port->dev, 998 "%s: serial or serial->private is NULL, status=%d\n", 999 __func__, status); 1000 return; 1001 } 1002 1003 /* handle oob callback */ 1004 if (priv->dp_port_num == serial_priv->ds_oob_port_num) { 1005 dev_dbg(&port->dev, "digi_write_bulk_callback: oob callback\n"); 1006 spin_lock(&priv->dp_port_lock); 1007 priv->dp_write_urb_in_use = 0; 1008 wake_up_interruptible(&port->write_wait); 1009 spin_unlock(&priv->dp_port_lock); 1010 return; 1011 } 1012 1013 /* try to send any buffered data on this port */ 1014 spin_lock(&priv->dp_port_lock); 1015 priv->dp_write_urb_in_use = 0; 1016 if (priv->dp_out_buf_len > 0) { 1017 *((unsigned char *)(port->write_urb->transfer_buffer)) 1018 = (unsigned char)DIGI_CMD_SEND_DATA; 1019 *((unsigned char *)(port->write_urb->transfer_buffer) + 1) 1020 = (unsigned char)priv->dp_out_buf_len; 1021 port->write_urb->transfer_buffer_length = 1022 priv->dp_out_buf_len + 2; 1023 memcpy(port->write_urb->transfer_buffer + 2, priv->dp_out_buf, 1024 priv->dp_out_buf_len); 1025 ret = usb_submit_urb(port->write_urb, GFP_ATOMIC); 1026 if (ret == 0) { 1027 priv->dp_write_urb_in_use = 1; 1028 priv->dp_out_buf_len = 0; 1029 } 1030 } 1031 /* wake up processes sleeping on writes immediately */ 1032 tty_port_tty_wakeup(&port->port); 1033 /* also queue up a wakeup at scheduler time, in case we */ 1034 /* lost the race in write_chan(). */ 1035 schedule_work(&priv->dp_wakeup_work); 1036 1037 spin_unlock(&priv->dp_port_lock); 1038 if (ret && ret != -EPERM) 1039 dev_err_console(port, 1040 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 1041 __func__, ret, priv->dp_port_num); 1042 } 1043 1044 static int digi_write_room(struct tty_struct *tty) 1045 { 1046 struct usb_serial_port *port = tty->driver_data; 1047 struct digi_port *priv = usb_get_serial_port_data(port); 1048 int room; 1049 unsigned long flags = 0; 1050 1051 spin_lock_irqsave(&priv->dp_port_lock, flags); 1052 1053 if (priv->dp_write_urb_in_use) 1054 room = 0; 1055 else 1056 room = port->bulk_out_size - 2 - priv->dp_out_buf_len; 1057 1058 spin_unlock_irqrestore(&priv->dp_port_lock, flags); 1059 dev_dbg(&port->dev, "digi_write_room: port=%d, room=%d\n", priv->dp_port_num, room); 1060 return room; 1061 1062 } 1063 1064 static int digi_chars_in_buffer(struct tty_struct *tty) 1065 { 1066 struct usb_serial_port *port = tty->driver_data; 1067 struct digi_port *priv = usb_get_serial_port_data(port); 1068 1069 if (priv->dp_write_urb_in_use) { 1070 dev_dbg(&port->dev, "digi_chars_in_buffer: port=%d, chars=%d\n", 1071 priv->dp_port_num, port->bulk_out_size - 2); 1072 /* return(port->bulk_out_size - 2); */ 1073 return 256; 1074 } else { 1075 dev_dbg(&port->dev, "digi_chars_in_buffer: port=%d, chars=%d\n", 1076 priv->dp_port_num, priv->dp_out_buf_len); 1077 return priv->dp_out_buf_len; 1078 } 1079 1080 } 1081 1082 static void digi_dtr_rts(struct usb_serial_port *port, int on) 1083 { 1084 /* Adjust DTR and RTS */ 1085 digi_set_modem_signals(port, on * (TIOCM_DTR|TIOCM_RTS), 1); 1086 } 1087 1088 static int digi_open(struct tty_struct *tty, struct usb_serial_port *port) 1089 { 1090 int ret; 1091 unsigned char buf[32]; 1092 struct digi_port *priv = usb_get_serial_port_data(port); 1093 struct ktermios not_termios; 1094 1095 /* be sure the device is started up */ 1096 if (digi_startup_device(port->serial) != 0) 1097 return -ENXIO; 1098 1099 /* read modem signals automatically whenever they change */ 1100 buf[0] = DIGI_CMD_READ_INPUT_SIGNALS; 1101 buf[1] = priv->dp_port_num; 1102 buf[2] = DIGI_ENABLE; 1103 buf[3] = 0; 1104 1105 /* flush fifos */ 1106 buf[4] = DIGI_CMD_IFLUSH_FIFO; 1107 buf[5] = priv->dp_port_num; 1108 buf[6] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1109 buf[7] = 0; 1110 1111 ret = digi_write_oob_command(port, buf, 8, 1); 1112 if (ret != 0) 1113 dev_dbg(&port->dev, "digi_open: write oob failed, ret=%d\n", ret); 1114 1115 /* set termios settings */ 1116 if (tty) { 1117 not_termios.c_cflag = ~tty->termios.c_cflag; 1118 not_termios.c_iflag = ~tty->termios.c_iflag; 1119 digi_set_termios(tty, port, ¬_termios); 1120 } 1121 return 0; 1122 } 1123 1124 1125 static void digi_close(struct usb_serial_port *port) 1126 { 1127 DEFINE_WAIT(wait); 1128 int ret; 1129 unsigned char buf[32]; 1130 struct digi_port *priv = usb_get_serial_port_data(port); 1131 1132 mutex_lock(&port->serial->disc_mutex); 1133 /* if disconnected, just clear flags */ 1134 if (port->serial->disconnected) 1135 goto exit; 1136 1137 /* FIXME: Transmit idle belongs in the wait_unti_sent path */ 1138 digi_transmit_idle(port, DIGI_CLOSE_TIMEOUT); 1139 1140 /* disable input flow control */ 1141 buf[0] = DIGI_CMD_SET_INPUT_FLOW_CONTROL; 1142 buf[1] = priv->dp_port_num; 1143 buf[2] = DIGI_DISABLE; 1144 buf[3] = 0; 1145 1146 /* disable output flow control */ 1147 buf[4] = DIGI_CMD_SET_OUTPUT_FLOW_CONTROL; 1148 buf[5] = priv->dp_port_num; 1149 buf[6] = DIGI_DISABLE; 1150 buf[7] = 0; 1151 1152 /* disable reading modem signals automatically */ 1153 buf[8] = DIGI_CMD_READ_INPUT_SIGNALS; 1154 buf[9] = priv->dp_port_num; 1155 buf[10] = DIGI_DISABLE; 1156 buf[11] = 0; 1157 1158 /* disable receive */ 1159 buf[12] = DIGI_CMD_RECEIVE_ENABLE; 1160 buf[13] = priv->dp_port_num; 1161 buf[14] = DIGI_DISABLE; 1162 buf[15] = 0; 1163 1164 /* flush fifos */ 1165 buf[16] = DIGI_CMD_IFLUSH_FIFO; 1166 buf[17] = priv->dp_port_num; 1167 buf[18] = DIGI_FLUSH_TX | DIGI_FLUSH_RX; 1168 buf[19] = 0; 1169 1170 ret = digi_write_oob_command(port, buf, 20, 0); 1171 if (ret != 0) 1172 dev_dbg(&port->dev, "digi_close: write oob failed, ret=%d\n", 1173 ret); 1174 /* wait for final commands on oob port to complete */ 1175 prepare_to_wait(&priv->dp_flush_wait, &wait, 1176 TASK_INTERRUPTIBLE); 1177 schedule_timeout(DIGI_CLOSE_TIMEOUT); 1178 finish_wait(&priv->dp_flush_wait, &wait); 1179 1180 /* shutdown any outstanding bulk writes */ 1181 usb_kill_urb(port->write_urb); 1182 exit: 1183 spin_lock_irq(&priv->dp_port_lock); 1184 priv->dp_write_urb_in_use = 0; 1185 wake_up_interruptible(&priv->dp_close_wait); 1186 spin_unlock_irq(&priv->dp_port_lock); 1187 mutex_unlock(&port->serial->disc_mutex); 1188 } 1189 1190 1191 /* 1192 * Digi Startup Device 1193 * 1194 * Starts reads on all ports. Must be called AFTER startup, with 1195 * urbs initialized. Returns 0 if successful, non-zero error otherwise. 1196 */ 1197 1198 static int digi_startup_device(struct usb_serial *serial) 1199 { 1200 int i, ret = 0; 1201 struct digi_serial *serial_priv = usb_get_serial_data(serial); 1202 struct usb_serial_port *port; 1203 1204 /* be sure this happens exactly once */ 1205 spin_lock(&serial_priv->ds_serial_lock); 1206 if (serial_priv->ds_device_started) { 1207 spin_unlock(&serial_priv->ds_serial_lock); 1208 return 0; 1209 } 1210 serial_priv->ds_device_started = 1; 1211 spin_unlock(&serial_priv->ds_serial_lock); 1212 1213 /* start reading from each bulk in endpoint for the device */ 1214 /* set USB_DISABLE_SPD flag for write bulk urbs */ 1215 for (i = 0; i < serial->type->num_ports + 1; i++) { 1216 port = serial->port[i]; 1217 ret = usb_submit_urb(port->read_urb, GFP_KERNEL); 1218 if (ret != 0) { 1219 dev_err(&port->dev, 1220 "%s: usb_submit_urb failed, ret=%d, port=%d\n", 1221 __func__, ret, i); 1222 break; 1223 } 1224 } 1225 return ret; 1226 } 1227 1228 static int digi_port_init(struct usb_serial_port *port, unsigned port_num) 1229 { 1230 struct digi_port *priv; 1231 1232 priv = kzalloc(sizeof(*priv), GFP_KERNEL); 1233 if (!priv) 1234 return -ENOMEM; 1235 1236 spin_lock_init(&priv->dp_port_lock); 1237 priv->dp_port_num = port_num; 1238 init_waitqueue_head(&priv->dp_transmit_idle_wait); 1239 init_waitqueue_head(&priv->dp_flush_wait); 1240 init_waitqueue_head(&priv->dp_close_wait); 1241 INIT_WORK(&priv->dp_wakeup_work, digi_wakeup_write_lock); 1242 priv->dp_port = port; 1243 1244 init_waitqueue_head(&port->write_wait); 1245 1246 usb_set_serial_port_data(port, priv); 1247 1248 return 0; 1249 } 1250 1251 static int digi_startup(struct usb_serial *serial) 1252 { 1253 struct device *dev = &serial->interface->dev; 1254 struct digi_serial *serial_priv; 1255 int ret; 1256 int i; 1257 1258 /* check whether the device has the expected number of endpoints */ 1259 if (serial->num_port_pointers < serial->type->num_ports + 1) { 1260 dev_err(dev, "OOB endpoints missing\n"); 1261 return -ENODEV; 1262 } 1263 1264 for (i = 0; i < serial->type->num_ports + 1 ; i++) { 1265 if (!serial->port[i]->read_urb) { 1266 dev_err(dev, "bulk-in endpoint missing\n"); 1267 return -ENODEV; 1268 } 1269 if (!serial->port[i]->write_urb) { 1270 dev_err(dev, "bulk-out endpoint missing\n"); 1271 return -ENODEV; 1272 } 1273 } 1274 1275 serial_priv = kzalloc(sizeof(*serial_priv), GFP_KERNEL); 1276 if (!serial_priv) 1277 return -ENOMEM; 1278 1279 spin_lock_init(&serial_priv->ds_serial_lock); 1280 serial_priv->ds_oob_port_num = serial->type->num_ports; 1281 serial_priv->ds_oob_port = serial->port[serial_priv->ds_oob_port_num]; 1282 1283 ret = digi_port_init(serial_priv->ds_oob_port, 1284 serial_priv->ds_oob_port_num); 1285 if (ret) { 1286 kfree(serial_priv); 1287 return ret; 1288 } 1289 1290 usb_set_serial_data(serial, serial_priv); 1291 1292 return 0; 1293 } 1294 1295 1296 static void digi_disconnect(struct usb_serial *serial) 1297 { 1298 int i; 1299 1300 /* stop reads and writes on all ports */ 1301 for (i = 0; i < serial->type->num_ports + 1; i++) { 1302 usb_kill_urb(serial->port[i]->read_urb); 1303 usb_kill_urb(serial->port[i]->write_urb); 1304 } 1305 } 1306 1307 1308 static void digi_release(struct usb_serial *serial) 1309 { 1310 struct digi_serial *serial_priv; 1311 struct digi_port *priv; 1312 1313 serial_priv = usb_get_serial_data(serial); 1314 1315 priv = usb_get_serial_port_data(serial_priv->ds_oob_port); 1316 kfree(priv); 1317 1318 kfree(serial_priv); 1319 } 1320 1321 static int digi_port_probe(struct usb_serial_port *port) 1322 { 1323 return digi_port_init(port, port->port_number); 1324 } 1325 1326 static int digi_port_remove(struct usb_serial_port *port) 1327 { 1328 struct digi_port *priv; 1329 1330 priv = usb_get_serial_port_data(port); 1331 kfree(priv); 1332 1333 return 0; 1334 } 1335 1336 static void digi_read_bulk_callback(struct urb *urb) 1337 { 1338 struct usb_serial_port *port = urb->context; 1339 struct digi_port *priv; 1340 struct digi_serial *serial_priv; 1341 int ret; 1342 int status = urb->status; 1343 1344 /* port sanity check, do not resubmit if port is not valid */ 1345 if (port == NULL) 1346 return; 1347 priv = usb_get_serial_port_data(port); 1348 if (priv == NULL) { 1349 dev_err(&port->dev, "%s: port->private is NULL, status=%d\n", 1350 __func__, status); 1351 return; 1352 } 1353 if (port->serial == NULL || 1354 (serial_priv = usb_get_serial_data(port->serial)) == NULL) { 1355 dev_err(&port->dev, "%s: serial is bad or serial->private " 1356 "is NULL, status=%d\n", __func__, status); 1357 return; 1358 } 1359 1360 /* do not resubmit urb if it has any status error */ 1361 if (status) { 1362 dev_err(&port->dev, 1363 "%s: nonzero read bulk status: status=%d, port=%d\n", 1364 __func__, status, priv->dp_port_num); 1365 return; 1366 } 1367 1368 /* handle oob or inb callback, do not resubmit if error */ 1369 if (priv->dp_port_num == serial_priv->ds_oob_port_num) { 1370 if (digi_read_oob_callback(urb) != 0) 1371 return; 1372 } else { 1373 if (digi_read_inb_callback(urb) != 0) 1374 return; 1375 } 1376 1377 /* continue read */ 1378 ret = usb_submit_urb(urb, GFP_ATOMIC); 1379 if (ret != 0 && ret != -EPERM) { 1380 dev_err(&port->dev, 1381 "%s: failed resubmitting urb, ret=%d, port=%d\n", 1382 __func__, ret, priv->dp_port_num); 1383 } 1384 1385 } 1386 1387 /* 1388 * Digi Read INB Callback 1389 * 1390 * Digi Read INB Callback handles reads on the in band ports, sending 1391 * the data on to the tty subsystem. When called we know port and 1392 * port->private are not NULL and port->serial has been validated. 1393 * It returns 0 if successful, 1 if successful but the port is 1394 * throttled, and -1 if the sanity checks failed. 1395 */ 1396 1397 static int digi_read_inb_callback(struct urb *urb) 1398 { 1399 struct usb_serial_port *port = urb->context; 1400 struct digi_port *priv = usb_get_serial_port_data(port); 1401 int opcode = ((unsigned char *)urb->transfer_buffer)[0]; 1402 int len = ((unsigned char *)urb->transfer_buffer)[1]; 1403 int port_status = ((unsigned char *)urb->transfer_buffer)[2]; 1404 unsigned char *data = ((unsigned char *)urb->transfer_buffer) + 3; 1405 int flag, throttled; 1406 int status = urb->status; 1407 1408 /* do not process callbacks on closed ports */ 1409 /* but do continue the read chain */ 1410 if (urb->status == -ENOENT) 1411 return 0; 1412 1413 /* short/multiple packet check */ 1414 if (urb->actual_length != len + 2) { 1415 dev_err(&port->dev, "%s: INCOMPLETE OR MULTIPLE PACKET, " 1416 "status=%d, port=%d, opcode=%d, len=%d, " 1417 "actual_length=%d, status=%d\n", __func__, status, 1418 priv->dp_port_num, opcode, len, urb->actual_length, 1419 port_status); 1420 return -1; 1421 } 1422 1423 spin_lock(&priv->dp_port_lock); 1424 1425 /* check for throttle; if set, do not resubmit read urb */ 1426 /* indicate the read chain needs to be restarted on unthrottle */ 1427 throttled = priv->dp_throttled; 1428 if (throttled) 1429 priv->dp_throttle_restart = 1; 1430 1431 /* receive data */ 1432 if (opcode == DIGI_CMD_RECEIVE_DATA) { 1433 /* get flag from port_status */ 1434 flag = 0; 1435 1436 /* overrun is special, not associated with a char */ 1437 if (port_status & DIGI_OVERRUN_ERROR) 1438 tty_insert_flip_char(&port->port, 0, TTY_OVERRUN); 1439 1440 /* break takes precedence over parity, */ 1441 /* which takes precedence over framing errors */ 1442 if (port_status & DIGI_BREAK_ERROR) 1443 flag = TTY_BREAK; 1444 else if (port_status & DIGI_PARITY_ERROR) 1445 flag = TTY_PARITY; 1446 else if (port_status & DIGI_FRAMING_ERROR) 1447 flag = TTY_FRAME; 1448 1449 /* data length is len-1 (one byte of len is port_status) */ 1450 --len; 1451 if (len > 0) { 1452 tty_insert_flip_string_fixed_flag(&port->port, data, 1453 flag, len); 1454 tty_flip_buffer_push(&port->port); 1455 } 1456 } 1457 spin_unlock(&priv->dp_port_lock); 1458 1459 if (opcode == DIGI_CMD_RECEIVE_DISABLE) 1460 dev_dbg(&port->dev, "%s: got RECEIVE_DISABLE\n", __func__); 1461 else if (opcode != DIGI_CMD_RECEIVE_DATA) 1462 dev_dbg(&port->dev, "%s: unknown opcode: %d\n", __func__, opcode); 1463 1464 return throttled ? 1 : 0; 1465 1466 } 1467 1468 1469 /* 1470 * Digi Read OOB Callback 1471 * 1472 * Digi Read OOB Callback handles reads on the out of band port. 1473 * When called we know port and port->private are not NULL and 1474 * the port->serial is valid. It returns 0 if successful, and 1475 * -1 if the sanity checks failed. 1476 */ 1477 1478 static int digi_read_oob_callback(struct urb *urb) 1479 { 1480 1481 struct usb_serial_port *port = urb->context; 1482 struct usb_serial *serial = port->serial; 1483 struct tty_struct *tty; 1484 struct digi_port *priv = usb_get_serial_port_data(port); 1485 int opcode, line, status, val; 1486 int i; 1487 unsigned int rts; 1488 1489 /* handle each oob command */ 1490 for (i = 0; i < urb->actual_length - 3;) { 1491 opcode = ((unsigned char *)urb->transfer_buffer)[i++]; 1492 line = ((unsigned char *)urb->transfer_buffer)[i++]; 1493 status = ((unsigned char *)urb->transfer_buffer)[i++]; 1494 val = ((unsigned char *)urb->transfer_buffer)[i++]; 1495 1496 dev_dbg(&port->dev, "digi_read_oob_callback: opcode=%d, line=%d, status=%d, val=%d\n", 1497 opcode, line, status, val); 1498 1499 if (status != 0 || line >= serial->type->num_ports) 1500 continue; 1501 1502 port = serial->port[line]; 1503 1504 priv = usb_get_serial_port_data(port); 1505 if (priv == NULL) 1506 return -1; 1507 1508 tty = tty_port_tty_get(&port->port); 1509 1510 rts = 0; 1511 if (tty) 1512 rts = C_CRTSCTS(tty); 1513 1514 if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) { 1515 spin_lock(&priv->dp_port_lock); 1516 /* convert from digi flags to termiox flags */ 1517 if (val & DIGI_READ_INPUT_SIGNALS_CTS) { 1518 priv->dp_modem_signals |= TIOCM_CTS; 1519 /* port must be open to use tty struct */ 1520 if (rts) 1521 tty_port_tty_wakeup(&port->port); 1522 } else { 1523 priv->dp_modem_signals &= ~TIOCM_CTS; 1524 /* port must be open to use tty struct */ 1525 } 1526 if (val & DIGI_READ_INPUT_SIGNALS_DSR) 1527 priv->dp_modem_signals |= TIOCM_DSR; 1528 else 1529 priv->dp_modem_signals &= ~TIOCM_DSR; 1530 if (val & DIGI_READ_INPUT_SIGNALS_RI) 1531 priv->dp_modem_signals |= TIOCM_RI; 1532 else 1533 priv->dp_modem_signals &= ~TIOCM_RI; 1534 if (val & DIGI_READ_INPUT_SIGNALS_DCD) 1535 priv->dp_modem_signals |= TIOCM_CD; 1536 else 1537 priv->dp_modem_signals &= ~TIOCM_CD; 1538 1539 spin_unlock(&priv->dp_port_lock); 1540 } else if (opcode == DIGI_CMD_TRANSMIT_IDLE) { 1541 spin_lock(&priv->dp_port_lock); 1542 priv->dp_transmit_idle = 1; 1543 wake_up_interruptible(&priv->dp_transmit_idle_wait); 1544 spin_unlock(&priv->dp_port_lock); 1545 } else if (opcode == DIGI_CMD_IFLUSH_FIFO) { 1546 wake_up_interruptible(&priv->dp_flush_wait); 1547 } 1548 tty_kref_put(tty); 1549 } 1550 return 0; 1551 1552 } 1553 1554 module_usb_serial_driver(serial_drivers, id_table_combined); 1555 1556 MODULE_AUTHOR(DRIVER_AUTHOR); 1557 MODULE_DESCRIPTION(DRIVER_DESC); 1558 MODULE_LICENSE("GPL"); 1559