xref: /openbmc/linux/drivers/usb/phy/phy-fsl-usb.h (revision b34e08d5) 
1 /* Copyright (C) 2007,2008 Freescale Semiconductor, Inc.
2  *
3  * This program is free software; you can redistribute  it and/or modify it
4  * under  the terms of  the GNU General  Public License as published by the
5  * Free Software Foundation;  either version 2 of the  License, or (at your
6  * option) any later version.
7  *
8  * This program is distributed in the hope that it will be useful, but
9  * WITHOUT ANY WARRANTY; without even the implied warranty of
10  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
11  * General Public License for more details.
12  *
13  * You should have received a copy of the  GNU General Public License along
14  * with this program; if not, write  to the Free Software Foundation, Inc.,
15  * 675 Mass Ave, Cambridge, MA 02139, USA.
16  */
17 
18 #include <linux/usb/otg-fsm.h>
19 #include <linux/usb/otg.h>
20 #include <linux/ioctl.h>
21 
22 /* USB Command Register Bit Masks */
23 #define USB_CMD_RUN_STOP		(0x1<<0)
24 #define USB_CMD_CTRL_RESET		(0x1<<1)
25 #define USB_CMD_PERIODIC_SCHEDULE_EN	(0x1<<4)
26 #define USB_CMD_ASYNC_SCHEDULE_EN	(0x1<<5)
27 #define USB_CMD_INT_AA_DOORBELL		(0x1<<6)
28 #define USB_CMD_ASP			(0x3<<8)
29 #define USB_CMD_ASYNC_SCH_PARK_EN	(0x1<<11)
30 #define USB_CMD_SUTW			(0x1<<13)
31 #define USB_CMD_ATDTW			(0x1<<14)
32 #define USB_CMD_ITC			(0xFF<<16)
33 
34 /* bit 15,3,2 are frame list size */
35 #define USB_CMD_FRAME_SIZE_1024		(0x0<<15 | 0x0<<2)
36 #define USB_CMD_FRAME_SIZE_512		(0x0<<15 | 0x1<<2)
37 #define USB_CMD_FRAME_SIZE_256		(0x0<<15 | 0x2<<2)
38 #define USB_CMD_FRAME_SIZE_128		(0x0<<15 | 0x3<<2)
39 #define USB_CMD_FRAME_SIZE_64		(0x1<<15 | 0x0<<2)
40 #define USB_CMD_FRAME_SIZE_32		(0x1<<15 | 0x1<<2)
41 #define USB_CMD_FRAME_SIZE_16		(0x1<<15 | 0x2<<2)
42 #define USB_CMD_FRAME_SIZE_8		(0x1<<15 | 0x3<<2)
43 
44 /* bit 9-8 are async schedule park mode count */
45 #define USB_CMD_ASP_00			(0x0<<8)
46 #define USB_CMD_ASP_01			(0x1<<8)
47 #define USB_CMD_ASP_10			(0x2<<8)
48 #define USB_CMD_ASP_11			(0x3<<8)
49 #define USB_CMD_ASP_BIT_POS		(8)
50 
51 /* bit 23-16 are interrupt threshold control */
52 #define USB_CMD_ITC_NO_THRESHOLD	(0x00<<16)
53 #define USB_CMD_ITC_1_MICRO_FRM		(0x01<<16)
54 #define USB_CMD_ITC_2_MICRO_FRM		(0x02<<16)
55 #define USB_CMD_ITC_4_MICRO_FRM		(0x04<<16)
56 #define USB_CMD_ITC_8_MICRO_FRM		(0x08<<16)
57 #define USB_CMD_ITC_16_MICRO_FRM	(0x10<<16)
58 #define USB_CMD_ITC_32_MICRO_FRM	(0x20<<16)
59 #define USB_CMD_ITC_64_MICRO_FRM	(0x40<<16)
60 #define USB_CMD_ITC_BIT_POS		(16)
61 
62 /* USB Status Register Bit Masks */
63 #define USB_STS_INT			(0x1<<0)
64 #define USB_STS_ERR			(0x1<<1)
65 #define USB_STS_PORT_CHANGE		(0x1<<2)
66 #define USB_STS_FRM_LST_ROLL		(0x1<<3)
67 #define USB_STS_SYS_ERR			(0x1<<4)
68 #define USB_STS_IAA			(0x1<<5)
69 #define USB_STS_RESET_RECEIVED		(0x1<<6)
70 #define USB_STS_SOF			(0x1<<7)
71 #define USB_STS_DCSUSPEND		(0x1<<8)
72 #define USB_STS_HC_HALTED		(0x1<<12)
73 #define USB_STS_RCL			(0x1<<13)
74 #define USB_STS_PERIODIC_SCHEDULE	(0x1<<14)
75 #define USB_STS_ASYNC_SCHEDULE		(0x1<<15)
76 
77 /* USB Interrupt Enable Register Bit Masks */
78 #define USB_INTR_INT_EN			(0x1<<0)
79 #define USB_INTR_ERR_INT_EN		(0x1<<1)
80 #define USB_INTR_PC_DETECT_EN		(0x1<<2)
81 #define USB_INTR_FRM_LST_ROLL_EN	(0x1<<3)
82 #define USB_INTR_SYS_ERR_EN		(0x1<<4)
83 #define USB_INTR_ASYN_ADV_EN		(0x1<<5)
84 #define USB_INTR_RESET_EN		(0x1<<6)
85 #define USB_INTR_SOF_EN			(0x1<<7)
86 #define USB_INTR_DEVICE_SUSPEND		(0x1<<8)
87 
88 /* Device Address bit masks */
89 #define USB_DEVICE_ADDRESS_MASK		(0x7F<<25)
90 #define USB_DEVICE_ADDRESS_BIT_POS	(25)
91 /* PORTSC  Register Bit Masks,Only one PORT in OTG mode*/
92 #define PORTSC_CURRENT_CONNECT_STATUS	(0x1<<0)
93 #define PORTSC_CONNECT_STATUS_CHANGE	(0x1<<1)
94 #define PORTSC_PORT_ENABLE		(0x1<<2)
95 #define PORTSC_PORT_EN_DIS_CHANGE	(0x1<<3)
96 #define PORTSC_OVER_CURRENT_ACT		(0x1<<4)
97 #define PORTSC_OVER_CUURENT_CHG		(0x1<<5)
98 #define PORTSC_PORT_FORCE_RESUME	(0x1<<6)
99 #define PORTSC_PORT_SUSPEND		(0x1<<7)
100 #define PORTSC_PORT_RESET		(0x1<<8)
101 #define PORTSC_LINE_STATUS_BITS		(0x3<<10)
102 #define PORTSC_PORT_POWER		(0x1<<12)
103 #define PORTSC_PORT_INDICTOR_CTRL	(0x3<<14)
104 #define PORTSC_PORT_TEST_CTRL		(0xF<<16)
105 #define PORTSC_WAKE_ON_CONNECT_EN	(0x1<<20)
106 #define PORTSC_WAKE_ON_CONNECT_DIS	(0x1<<21)
107 #define PORTSC_WAKE_ON_OVER_CURRENT	(0x1<<22)
108 #define PORTSC_PHY_LOW_POWER_SPD	(0x1<<23)
109 #define PORTSC_PORT_FORCE_FULL_SPEED	(0x1<<24)
110 #define PORTSC_PORT_SPEED_MASK		(0x3<<26)
111 #define PORTSC_TRANSCEIVER_WIDTH	(0x1<<28)
112 #define PORTSC_PHY_TYPE_SEL		(0x3<<30)
113 /* bit 11-10 are line status */
114 #define PORTSC_LINE_STATUS_SE0		(0x0<<10)
115 #define PORTSC_LINE_STATUS_JSTATE	(0x1<<10)
116 #define PORTSC_LINE_STATUS_KSTATE	(0x2<<10)
117 #define PORTSC_LINE_STATUS_UNDEF	(0x3<<10)
118 #define PORTSC_LINE_STATUS_BIT_POS	(10)
119 
120 /* bit 15-14 are port indicator control */
121 #define PORTSC_PIC_OFF			(0x0<<14)
122 #define PORTSC_PIC_AMBER		(0x1<<14)
123 #define PORTSC_PIC_GREEN		(0x2<<14)
124 #define PORTSC_PIC_UNDEF		(0x3<<14)
125 #define PORTSC_PIC_BIT_POS		(14)
126 
127 /* bit 19-16 are port test control */
128 #define PORTSC_PTC_DISABLE		(0x0<<16)
129 #define PORTSC_PTC_JSTATE		(0x1<<16)
130 #define PORTSC_PTC_KSTATE		(0x2<<16)
131 #define PORTSC_PTC_SEQNAK		(0x3<<16)
132 #define PORTSC_PTC_PACKET		(0x4<<16)
133 #define PORTSC_PTC_FORCE_EN		(0x5<<16)
134 #define PORTSC_PTC_BIT_POS		(16)
135 
136 /* bit 27-26 are port speed */
137 #define PORTSC_PORT_SPEED_FULL		(0x0<<26)
138 #define PORTSC_PORT_SPEED_LOW		(0x1<<26)
139 #define PORTSC_PORT_SPEED_HIGH		(0x2<<26)
140 #define PORTSC_PORT_SPEED_UNDEF		(0x3<<26)
141 #define PORTSC_SPEED_BIT_POS		(26)
142 
143 /* bit 28 is parallel transceiver width for UTMI interface */
144 #define PORTSC_PTW			(0x1<<28)
145 #define PORTSC_PTW_8BIT			(0x0<<28)
146 #define PORTSC_PTW_16BIT		(0x1<<28)
147 
148 /* bit 31-30 are port transceiver select */
149 #define PORTSC_PTS_UTMI			(0x0<<30)
150 #define PORTSC_PTS_ULPI			(0x2<<30)
151 #define PORTSC_PTS_FSLS_SERIAL		(0x3<<30)
152 #define PORTSC_PTS_BIT_POS		(30)
153 
154 #define PORTSC_W1C_BITS			\
155 	(PORTSC_CONNECT_STATUS_CHANGE |	\
156 	 PORTSC_PORT_EN_DIS_CHANGE    |	\
157 	 PORTSC_OVER_CUURENT_CHG)
158 
159 /* OTG Status Control Register Bit Masks */
160 #define OTGSC_CTRL_VBUS_DISCHARGE	(0x1<<0)
161 #define OTGSC_CTRL_VBUS_CHARGE		(0x1<<1)
162 #define OTGSC_CTRL_OTG_TERMINATION	(0x1<<3)
163 #define OTGSC_CTRL_DATA_PULSING		(0x1<<4)
164 #define OTGSC_CTRL_ID_PULL_EN		(0x1<<5)
165 #define OTGSC_HA_DATA_PULSE		(0x1<<6)
166 #define OTGSC_HA_BA			(0x1<<7)
167 #define OTGSC_STS_USB_ID		(0x1<<8)
168 #define OTGSC_STS_A_VBUS_VALID		(0x1<<9)
169 #define OTGSC_STS_A_SESSION_VALID	(0x1<<10)
170 #define OTGSC_STS_B_SESSION_VALID	(0x1<<11)
171 #define OTGSC_STS_B_SESSION_END		(0x1<<12)
172 #define OTGSC_STS_1MS_TOGGLE		(0x1<<13)
173 #define OTGSC_STS_DATA_PULSING		(0x1<<14)
174 #define OTGSC_INTSTS_USB_ID		(0x1<<16)
175 #define OTGSC_INTSTS_A_VBUS_VALID	(0x1<<17)
176 #define OTGSC_INTSTS_A_SESSION_VALID	(0x1<<18)
177 #define OTGSC_INTSTS_B_SESSION_VALID	(0x1<<19)
178 #define OTGSC_INTSTS_B_SESSION_END	(0x1<<20)
179 #define OTGSC_INTSTS_1MS		(0x1<<21)
180 #define OTGSC_INTSTS_DATA_PULSING	(0x1<<22)
181 #define OTGSC_INTR_USB_ID_EN		(0x1<<24)
182 #define OTGSC_INTR_A_VBUS_VALID_EN	(0x1<<25)
183 #define OTGSC_INTR_A_SESSION_VALID_EN	(0x1<<26)
184 #define OTGSC_INTR_B_SESSION_VALID_EN	(0x1<<27)
185 #define OTGSC_INTR_B_SESSION_END_EN	(0x1<<28)
186 #define OTGSC_INTR_1MS_TIMER_EN		(0x1<<29)
187 #define OTGSC_INTR_DATA_PULSING_EN	(0x1<<30)
188 #define OTGSC_INTSTS_MASK		(0x00ff0000)
189 
190 /* USB MODE Register Bit Masks */
191 #define  USB_MODE_CTRL_MODE_IDLE	(0x0<<0)
192 #define  USB_MODE_CTRL_MODE_DEVICE	(0x2<<0)
193 #define  USB_MODE_CTRL_MODE_HOST	(0x3<<0)
194 #define  USB_MODE_CTRL_MODE_RSV		(0x1<<0)
195 #define  USB_MODE_SETUP_LOCK_OFF	(0x1<<3)
196 #define  USB_MODE_STREAM_DISABLE	(0x1<<4)
197 #define  USB_MODE_ES			(0x1<<2) /* Endian Select */
198 
199 /* control Register Bit Masks */
200 #define  USB_CTRL_IOENB			(0x1<<2)
201 #define  USB_CTRL_ULPI_INT0EN		(0x1<<0)
202 
203 /* BCSR5 */
204 #define BCSR5_INT_USB			(0x02)
205 
206 /* USB module clk cfg */
207 #define SCCR_OFFS			(0xA08)
208 #define SCCR_USB_CLK_DISABLE		(0x00000000)	/* USB clk disable */
209 #define SCCR_USB_MPHCM_11		(0x00c00000)
210 #define SCCR_USB_MPHCM_01		(0x00400000)
211 #define SCCR_USB_MPHCM_10		(0x00800000)
212 #define SCCR_USB_DRCM_11		(0x00300000)
213 #define SCCR_USB_DRCM_01		(0x00100000)
214 #define SCCR_USB_DRCM_10		(0x00200000)
215 
216 #define SICRL_OFFS			(0x114)
217 #define SICRL_USB0			(0x40000000)
218 #define SICRL_USB1			(0x20000000)
219 
220 #define SICRH_OFFS			(0x118)
221 #define SICRH_USB_UTMI			(0x00020000)
222 
223 /* OTG interrupt enable bit masks */
224 #define  OTGSC_INTERRUPT_ENABLE_BITS_MASK  \
225 	(OTGSC_INTR_USB_ID_EN            | \
226 	OTGSC_INTR_1MS_TIMER_EN		 | \
227 	OTGSC_INTR_A_VBUS_VALID_EN       | \
228 	OTGSC_INTR_A_SESSION_VALID_EN    | \
229 	OTGSC_INTR_B_SESSION_VALID_EN    | \
230 	OTGSC_INTR_B_SESSION_END_EN      | \
231 	OTGSC_INTR_DATA_PULSING_EN)
232 
233 /* OTG interrupt status bit masks */
234 #define  OTGSC_INTERRUPT_STATUS_BITS_MASK  \
235 	(OTGSC_INTSTS_USB_ID          |    \
236 	OTGSC_INTR_1MS_TIMER_EN       |    \
237 	OTGSC_INTSTS_A_VBUS_VALID     |    \
238 	OTGSC_INTSTS_A_SESSION_VALID  |    \
239 	OTGSC_INTSTS_B_SESSION_VALID  |    \
240 	OTGSC_INTSTS_B_SESSION_END    |    \
241 	OTGSC_INTSTS_DATA_PULSING)
242 
243 /*
244  *  A-DEVICE timing  constants
245  */
246 
247 /* Wait for VBUS Rise  */
248 #define TA_WAIT_VRISE	(100)	/* a_wait_vrise 100 ms, section: 6.6.5.1 */
249 
250 /* Wait for B-Connect */
251 #define TA_WAIT_BCON	(10000)  /* a_wait_bcon > 1 sec, section: 6.6.5.2
252 				  * This is only used to get out of
253 				  * OTG_STATE_A_WAIT_BCON state if there was
254 				  * no connection for these many milliseconds
255 				  */
256 
257 /* A-Idle to B-Disconnect */
258 /* It is necessary for this timer to be more than 750 ms because of a bug in OPT
259  * test 5.4 in which B OPT disconnects after 750 ms instead of 75ms as stated
260  * in the test description
261  */
262 #define TA_AIDL_BDIS	(5000)	/* a_suspend minimum 200 ms, section: 6.6.5.3 */
263 
264 /* B-Idle to A-Disconnect */
265 #define TA_BIDL_ADIS	(12)	/* 3 to 200 ms */
266 
267 /* B-device timing constants */
268 
269 
270 /* Data-Line Pulse Time*/
271 #define TB_DATA_PLS	(10)	/* b_srp_init,continue 5~10ms, section:5.3.3 */
272 #define TB_DATA_PLS_MIN	(5)	/* minimum 5 ms */
273 #define TB_DATA_PLS_MAX	(10)	/* maximum 10 ms */
274 
275 /* SRP Initiate Time  */
276 #define TB_SRP_INIT	(100)	/* b_srp_init,maximum 100 ms, section:5.3.8 */
277 
278 /* SRP Fail Time  */
279 #define TB_SRP_FAIL	(7000)	/* b_srp_init,Fail time 5~30s, section:6.8.2.2*/
280 
281 /* SRP result wait time */
282 #define TB_SRP_WAIT	(60)
283 
284 /* VBus time */
285 #define TB_VBUS_PLS	(30)	/* time to keep vbus pulsing asserted */
286 
287 /* Discharge time */
288 /* This time should be less than 10ms. It varies from system to system. */
289 #define TB_VBUS_DSCHRG	(8)
290 
291 /* A-SE0 to B-Reset  */
292 #define TB_ASE0_BRST	(20)	/* b_wait_acon, mini 3.125 ms,section:6.8.2.4 */
293 
294 /* A bus suspend timer before we can switch to b_wait_aconn */
295 #define TB_A_SUSPEND	(7)
296 #define TB_BUS_RESUME	(12)
297 
298 /* SE0 Time Before SRP */
299 #define TB_SE0_SRP	(2)	/* b_idle,minimum 2 ms, section:5.3.2 */
300 
301 #define SET_OTG_STATE(otg_ptr, newstate)	((otg_ptr)->state = newstate)
302 
303 struct usb_dr_mmap {
304 	/* Capability register */
305 	u8 res1[256];
306 	u16 caplength;		/* Capability Register Length */
307 	u16 hciversion;		/* Host Controller Interface Version */
308 	u32 hcsparams;		/* Host Controller Structual Parameters */
309 	u32 hccparams;		/* Host Controller Capability Parameters */
310 	u8 res2[20];
311 	u32 dciversion;		/* Device Controller Interface Version */
312 	u32 dccparams;		/* Device Controller Capability Parameters */
313 	u8 res3[24];
314 	/* Operation register */
315 	u32 usbcmd;		/* USB Command Register */
316 	u32 usbsts;		/* USB Status Register */
317 	u32 usbintr;		/* USB Interrupt Enable Register */
318 	u32 frindex;		/* Frame Index Register */
319 	u8 res4[4];
320 	u32 deviceaddr;		/* Device Address */
321 	u32 endpointlistaddr;	/* Endpoint List Address Register */
322 	u8 res5[4];
323 	u32 burstsize;		/* Master Interface Data Burst Size Register */
324 	u32 txttfilltuning;	/* Transmit FIFO Tuning Controls Register */
325 	u8 res6[8];
326 	u32 ulpiview;		/* ULPI register access */
327 	u8 res7[12];
328 	u32 configflag;		/* Configure Flag Register */
329 	u32 portsc;		/* Port 1 Status and Control Register */
330 	u8 res8[28];
331 	u32 otgsc;		/* On-The-Go Status and Control */
332 	u32 usbmode;		/* USB Mode Register */
333 	u32 endptsetupstat;	/* Endpoint Setup Status Register */
334 	u32 endpointprime;	/* Endpoint Initialization Register */
335 	u32 endptflush;		/* Endpoint Flush Register */
336 	u32 endptstatus;	/* Endpoint Status Register */
337 	u32 endptcomplete;	/* Endpoint Complete Register */
338 	u32 endptctrl[6];	/* Endpoint Control Registers */
339 	u8 res9[552];
340 	u32 snoop1;
341 	u32 snoop2;
342 	u32 age_cnt_thresh;	/* Age Count Threshold Register */
343 	u32 pri_ctrl;		/* Priority Control Register */
344 	u32 si_ctrl;		/* System Interface Control Register */
345 	u8 res10[236];
346 	u32 control;		/* General Purpose Control Register */
347 };
348 
349 struct fsl_otg_timer {
350 	unsigned long expires;	/* Number of count increase to timeout */
351 	unsigned long count;	/* Tick counter */
352 	void (*function)(unsigned long);	/* Timeout function */
353 	unsigned long data;	/* Data passed to function */
354 	struct list_head list;
355 };
356 
357 inline struct fsl_otg_timer *otg_timer_initializer
358 (void (*function)(unsigned long), unsigned long expires, unsigned long data)
359 {
360 	struct fsl_otg_timer *timer;
361 
362 	timer = kmalloc(sizeof(struct fsl_otg_timer), GFP_KERNEL);
363 	if (!timer)
364 		return NULL;
365 	timer->function = function;
366 	timer->expires = expires;
367 	timer->data = data;
368 	return timer;
369 }
370 
371 struct fsl_otg {
372 	struct usb_phy phy;
373 	struct otg_fsm fsm;
374 	struct usb_dr_mmap *dr_mem_map;
375 	struct delayed_work otg_event;
376 
377 	/* used for usb host */
378 	struct work_struct work_wq;
379 	u8	host_working;
380 
381 	int irq;
382 };
383 
384 struct fsl_otg_config {
385 	u8 otg_port;
386 };
387 
388 /* For SRP and HNP handle */
389 #define FSL_OTG_MAJOR		240
390 #define FSL_OTG_NAME		"fsl-usb2-otg"
391 /* Command to OTG driver ioctl */
392 #define OTG_IOCTL_MAGIC		FSL_OTG_MAJOR
393 /* if otg work as host, it should return 1, otherwise return 0 */
394 #define GET_OTG_STATUS		_IOR(OTG_IOCTL_MAGIC, 1, int)
395 #define SET_A_SUSPEND_REQ	_IOW(OTG_IOCTL_MAGIC, 2, int)
396 #define SET_A_BUS_DROP		_IOW(OTG_IOCTL_MAGIC, 3, int)
397 #define SET_A_BUS_REQ		_IOW(OTG_IOCTL_MAGIC, 4, int)
398 #define SET_B_BUS_REQ		_IOW(OTG_IOCTL_MAGIC, 5, int)
399 #define GET_A_SUSPEND_REQ	_IOR(OTG_IOCTL_MAGIC, 6, int)
400 #define GET_A_BUS_DROP		_IOR(OTG_IOCTL_MAGIC, 7, int)
401 #define GET_A_BUS_REQ		_IOR(OTG_IOCTL_MAGIC, 8, int)
402 #define GET_B_BUS_REQ		_IOR(OTG_IOCTL_MAGIC, 9, int)
403 
404 void fsl_otg_add_timer(struct otg_fsm *fsm, void *timer);
405 void fsl_otg_del_timer(struct otg_fsm *fsm, void *timer);
406 void fsl_otg_pulse_vbus(void);
407