1 /* 2 * drivers/usb/otg/ab8500_usb.c 3 * 4 * USB transceiver driver for AB8500 chip 5 * 6 * Copyright (C) 2010 ST-Ericsson AB 7 * Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License as published by 11 * the Free Software Foundation; either version 2 of the License, or 12 * (at your option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; if not, write to the Free Software 21 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 22 * 23 */ 24 25 #include <linux/module.h> 26 #include <linux/platform_device.h> 27 #include <linux/usb/otg.h> 28 #include <linux/slab.h> 29 #include <linux/notifier.h> 30 #include <linux/interrupt.h> 31 #include <linux/delay.h> 32 #include <linux/mfd/abx500.h> 33 #include <linux/mfd/abx500/ab8500.h> 34 #include <linux/usb/musb-ux500.h> 35 #include <linux/regulator/consumer.h> 36 #include <linux/pinctrl/consumer.h> 37 38 /* Bank AB8500_SYS_CTRL2_BLOCK */ 39 #define AB8500_MAIN_WD_CTRL_REG 0x01 40 41 /* Bank AB8500_USB */ 42 #define AB8500_USB_LINE_STAT_REG 0x80 43 #define AB8505_USB_LINE_STAT_REG 0x94 44 #define AB8500_USB_PHY_CTRL_REG 0x8A 45 46 /* Bank AB8500_DEVELOPMENT */ 47 #define AB8500_BANK12_ACCESS 0x00 48 49 /* Bank AB8500_DEBUG */ 50 #define AB8500_USB_PHY_TUNE1 0x05 51 #define AB8500_USB_PHY_TUNE2 0x06 52 #define AB8500_USB_PHY_TUNE3 0x07 53 54 #define AB8500_BIT_OTG_STAT_ID (1 << 0) 55 #define AB8500_BIT_PHY_CTRL_HOST_EN (1 << 0) 56 #define AB8500_BIT_PHY_CTRL_DEVICE_EN (1 << 1) 57 #define AB8500_BIT_WD_CTRL_ENABLE (1 << 0) 58 #define AB8500_BIT_WD_CTRL_KICK (1 << 1) 59 60 #define AB8500_WD_KICK_DELAY_US 100 /* usec */ 61 #define AB8500_WD_V11_DISABLE_DELAY_US 100 /* usec */ 62 #define AB8500_V20_31952_DISABLE_DELAY_US 100 /* usec */ 63 64 /* Usb line status register */ 65 enum ab8500_usb_link_status { 66 USB_LINK_NOT_CONFIGURED_8500 = 0, 67 USB_LINK_STD_HOST_NC_8500, 68 USB_LINK_STD_HOST_C_NS_8500, 69 USB_LINK_STD_HOST_C_S_8500, 70 USB_LINK_HOST_CHG_NM_8500, 71 USB_LINK_HOST_CHG_HS_8500, 72 USB_LINK_HOST_CHG_HS_CHIRP_8500, 73 USB_LINK_DEDICATED_CHG_8500, 74 USB_LINK_ACA_RID_A_8500, 75 USB_LINK_ACA_RID_B_8500, 76 USB_LINK_ACA_RID_C_NM_8500, 77 USB_LINK_ACA_RID_C_HS_8500, 78 USB_LINK_ACA_RID_C_HS_CHIRP_8500, 79 USB_LINK_HM_IDGND_8500, 80 USB_LINK_RESERVED_8500, 81 USB_LINK_NOT_VALID_LINK_8500, 82 }; 83 84 enum ab8505_usb_link_status { 85 USB_LINK_NOT_CONFIGURED_8505 = 0, 86 USB_LINK_STD_HOST_NC_8505, 87 USB_LINK_STD_HOST_C_NS_8505, 88 USB_LINK_STD_HOST_C_S_8505, 89 USB_LINK_CDP_8505, 90 USB_LINK_RESERVED0_8505, 91 USB_LINK_RESERVED1_8505, 92 USB_LINK_DEDICATED_CHG_8505, 93 USB_LINK_ACA_RID_A_8505, 94 USB_LINK_ACA_RID_B_8505, 95 USB_LINK_ACA_RID_C_NM_8505, 96 USB_LINK_RESERVED2_8505, 97 USB_LINK_RESERVED3_8505, 98 USB_LINK_HM_IDGND_8505, 99 USB_LINK_CHARGERPORT_NOT_OK_8505, 100 USB_LINK_CHARGER_DM_HIGH_8505, 101 USB_LINK_PHYEN_NO_VBUS_NO_IDGND_8505, 102 USB_LINK_STD_UPSTREAM_NO_IDGNG_NO_VBUS_8505, 103 USB_LINK_STD_UPSTREAM_8505, 104 USB_LINK_CHARGER_SE1_8505, 105 USB_LINK_CARKIT_CHGR_1_8505, 106 USB_LINK_CARKIT_CHGR_2_8505, 107 USB_LINK_ACA_DOCK_CHGR_8505, 108 USB_LINK_SAMSUNG_BOOT_CBL_PHY_EN_8505, 109 USB_LINK_SAMSUNG_BOOT_CBL_PHY_DISB_8505, 110 USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505, 111 USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505, 112 USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_8505, 113 }; 114 115 enum ab8500_usb_mode { 116 USB_IDLE = 0, 117 USB_PERIPHERAL, 118 USB_HOST, 119 USB_DEDICATED_CHG 120 }; 121 122 struct ab8500_usb { 123 struct usb_phy phy; 124 struct device *dev; 125 struct ab8500 *ab8500; 126 unsigned vbus_draw; 127 struct work_struct phy_dis_work; 128 enum ab8500_usb_mode mode; 129 struct regulator *v_ape; 130 struct regulator *v_musb; 131 struct regulator *v_ulpi; 132 int saved_v_ulpi; 133 int previous_link_status_state; 134 struct pinctrl *pinctrl; 135 struct pinctrl_state *pins_sleep; 136 }; 137 138 static inline struct ab8500_usb *phy_to_ab(struct usb_phy *x) 139 { 140 return container_of(x, struct ab8500_usb, phy); 141 } 142 143 static void ab8500_usb_wd_workaround(struct ab8500_usb *ab) 144 { 145 abx500_set_register_interruptible(ab->dev, 146 AB8500_SYS_CTRL2_BLOCK, 147 AB8500_MAIN_WD_CTRL_REG, 148 AB8500_BIT_WD_CTRL_ENABLE); 149 150 udelay(AB8500_WD_KICK_DELAY_US); 151 152 abx500_set_register_interruptible(ab->dev, 153 AB8500_SYS_CTRL2_BLOCK, 154 AB8500_MAIN_WD_CTRL_REG, 155 (AB8500_BIT_WD_CTRL_ENABLE 156 | AB8500_BIT_WD_CTRL_KICK)); 157 158 udelay(AB8500_WD_V11_DISABLE_DELAY_US); 159 160 abx500_set_register_interruptible(ab->dev, 161 AB8500_SYS_CTRL2_BLOCK, 162 AB8500_MAIN_WD_CTRL_REG, 163 0); 164 } 165 166 static void ab8500_usb_regulator_enable(struct ab8500_usb *ab) 167 { 168 int ret, volt; 169 170 ret = regulator_enable(ab->v_ape); 171 if (ret) 172 dev_err(ab->dev, "Failed to enable v-ape\n"); 173 174 if (!is_ab8500_2p0_or_earlier(ab->ab8500)) { 175 ab->saved_v_ulpi = regulator_get_voltage(ab->v_ulpi); 176 if (ab->saved_v_ulpi < 0) 177 dev_err(ab->dev, "Failed to get v_ulpi voltage\n"); 178 179 ret = regulator_set_voltage(ab->v_ulpi, 1300000, 1350000); 180 if (ret < 0) 181 dev_err(ab->dev, "Failed to set the Vintcore to 1.3V, ret=%d\n", 182 ret); 183 184 ret = regulator_set_optimum_mode(ab->v_ulpi, 28000); 185 if (ret < 0) 186 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", 187 ret); 188 } 189 190 ret = regulator_enable(ab->v_ulpi); 191 if (ret) 192 dev_err(ab->dev, "Failed to enable vddulpivio18\n"); 193 194 if (!is_ab8500_2p0_or_earlier(ab->ab8500)) { 195 volt = regulator_get_voltage(ab->v_ulpi); 196 if ((volt != 1300000) && (volt != 1350000)) 197 dev_err(ab->dev, "Vintcore is not set to 1.3V volt=%d\n", 198 volt); 199 } 200 201 ret = regulator_enable(ab->v_musb); 202 if (ret) 203 dev_err(ab->dev, "Failed to enable musb_1v8\n"); 204 } 205 206 static void ab8500_usb_regulator_disable(struct ab8500_usb *ab) 207 { 208 int ret; 209 210 regulator_disable(ab->v_musb); 211 212 regulator_disable(ab->v_ulpi); 213 214 /* USB is not the only consumer of Vintcore, restore old settings */ 215 if (!is_ab8500_2p0_or_earlier(ab->ab8500)) { 216 if (ab->saved_v_ulpi > 0) { 217 ret = regulator_set_voltage(ab->v_ulpi, 218 ab->saved_v_ulpi, ab->saved_v_ulpi); 219 if (ret < 0) 220 dev_err(ab->dev, "Failed to set the Vintcore to %duV, ret=%d\n", 221 ab->saved_v_ulpi, ret); 222 } 223 224 ret = regulator_set_optimum_mode(ab->v_ulpi, 0); 225 if (ret < 0) 226 dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", 227 ret); 228 } 229 230 regulator_disable(ab->v_ape); 231 } 232 233 static void ab8500_usb_wd_linkstatus(struct ab8500_usb *ab, u8 bit) 234 { 235 /* Workaround for v2.0 bug # 31952 */ 236 if (is_ab8500_2p0(ab->ab8500)) { 237 abx500_mask_and_set_register_interruptible(ab->dev, 238 AB8500_USB, AB8500_USB_PHY_CTRL_REG, 239 bit, bit); 240 udelay(AB8500_V20_31952_DISABLE_DELAY_US); 241 } 242 } 243 244 static void ab8500_usb_phy_enable(struct ab8500_usb *ab, bool sel_host) 245 { 246 u8 bit; 247 bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN : 248 AB8500_BIT_PHY_CTRL_DEVICE_EN; 249 250 /* mux and configure USB pins to DEFAULT state */ 251 ab->pinctrl = pinctrl_get_select(ab->dev, PINCTRL_STATE_DEFAULT); 252 if (IS_ERR(ab->pinctrl)) 253 dev_err(ab->dev, "could not get/set default pinstate\n"); 254 255 ab8500_usb_regulator_enable(ab); 256 257 abx500_mask_and_set_register_interruptible(ab->dev, 258 AB8500_USB, AB8500_USB_PHY_CTRL_REG, 259 bit, bit); 260 } 261 262 static void ab8500_usb_phy_disable(struct ab8500_usb *ab, bool sel_host) 263 { 264 u8 bit; 265 bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN : 266 AB8500_BIT_PHY_CTRL_DEVICE_EN; 267 268 ab8500_usb_wd_linkstatus(ab, bit); 269 270 abx500_mask_and_set_register_interruptible(ab->dev, 271 AB8500_USB, AB8500_USB_PHY_CTRL_REG, 272 bit, 0); 273 274 /* Needed to disable the phy.*/ 275 ab8500_usb_wd_workaround(ab); 276 277 ab8500_usb_regulator_disable(ab); 278 279 if (!IS_ERR(ab->pinctrl)) { 280 /* configure USB pins to SLEEP state */ 281 ab->pins_sleep = pinctrl_lookup_state(ab->pinctrl, 282 PINCTRL_STATE_SLEEP); 283 284 if (IS_ERR(ab->pins_sleep)) 285 dev_dbg(ab->dev, "could not get sleep pinstate\n"); 286 else if (pinctrl_select_state(ab->pinctrl, ab->pins_sleep)) 287 dev_err(ab->dev, "could not set pins to sleep state\n"); 288 289 /* as USB pins are shared with idddet, release them to allow 290 * iddet to request them 291 */ 292 pinctrl_put(ab->pinctrl); 293 } 294 } 295 296 #define ab8500_usb_host_phy_en(ab) ab8500_usb_phy_enable(ab, true) 297 #define ab8500_usb_host_phy_dis(ab) ab8500_usb_phy_disable(ab, true) 298 #define ab8500_usb_peri_phy_en(ab) ab8500_usb_phy_enable(ab, false) 299 #define ab8500_usb_peri_phy_dis(ab) ab8500_usb_phy_disable(ab, false) 300 301 static int ab8505_usb_link_status_update(struct ab8500_usb *ab, 302 enum ab8505_usb_link_status lsts) 303 { 304 enum ux500_musb_vbus_id_status event = 0; 305 306 dev_dbg(ab->dev, "ab8505_usb_link_status_update %d\n", lsts); 307 308 /* 309 * Spurious link_status interrupts are seen at the time of 310 * disconnection of a device in RIDA state 311 */ 312 if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8505 && 313 (lsts == USB_LINK_STD_HOST_NC_8505)) 314 return 0; 315 316 ab->previous_link_status_state = lsts; 317 318 switch (lsts) { 319 case USB_LINK_ACA_RID_B_8505: 320 event = UX500_MUSB_RIDB; 321 case USB_LINK_NOT_CONFIGURED_8505: 322 case USB_LINK_RESERVED0_8505: 323 case USB_LINK_RESERVED1_8505: 324 case USB_LINK_RESERVED2_8505: 325 case USB_LINK_RESERVED3_8505: 326 ab->mode = USB_IDLE; 327 ab->phy.otg->default_a = false; 328 ab->vbus_draw = 0; 329 if (event != UX500_MUSB_RIDB) 330 event = UX500_MUSB_NONE; 331 /* 332 * Fallback to default B_IDLE as nothing 333 * is connected 334 */ 335 ab->phy.state = OTG_STATE_B_IDLE; 336 break; 337 338 case USB_LINK_ACA_RID_C_NM_8505: 339 event = UX500_MUSB_RIDC; 340 case USB_LINK_STD_HOST_NC_8505: 341 case USB_LINK_STD_HOST_C_NS_8505: 342 case USB_LINK_STD_HOST_C_S_8505: 343 case USB_LINK_CDP_8505: 344 if (ab->mode == USB_IDLE) { 345 ab->mode = USB_PERIPHERAL; 346 ab8500_usb_peri_phy_en(ab); 347 atomic_notifier_call_chain(&ab->phy.notifier, 348 UX500_MUSB_PREPARE, &ab->vbus_draw); 349 } 350 if (event != UX500_MUSB_RIDC) 351 event = UX500_MUSB_VBUS; 352 break; 353 354 case USB_LINK_ACA_RID_A_8505: 355 case USB_LINK_ACA_DOCK_CHGR_8505: 356 event = UX500_MUSB_RIDA; 357 case USB_LINK_HM_IDGND_8505: 358 if (ab->mode == USB_IDLE) { 359 ab->mode = USB_HOST; 360 ab8500_usb_host_phy_en(ab); 361 atomic_notifier_call_chain(&ab->phy.notifier, 362 UX500_MUSB_PREPARE, &ab->vbus_draw); 363 } 364 ab->phy.otg->default_a = true; 365 if (event != UX500_MUSB_RIDA) 366 event = UX500_MUSB_ID; 367 atomic_notifier_call_chain(&ab->phy.notifier, 368 event, &ab->vbus_draw); 369 break; 370 371 case USB_LINK_DEDICATED_CHG_8505: 372 ab->mode = USB_DEDICATED_CHG; 373 event = UX500_MUSB_CHARGER; 374 atomic_notifier_call_chain(&ab->phy.notifier, 375 event, &ab->vbus_draw); 376 break; 377 378 default: 379 break; 380 } 381 382 return 0; 383 } 384 385 static int ab8500_usb_link_status_update(struct ab8500_usb *ab, 386 enum ab8500_usb_link_status lsts) 387 { 388 enum ux500_musb_vbus_id_status event = 0; 389 390 dev_dbg(ab->dev, "ab8500_usb_link_status_update %d\n", lsts); 391 392 /* 393 * Spurious link_status interrupts are seen in case of a 394 * disconnection of a device in IDGND and RIDA stage 395 */ 396 if (ab->previous_link_status_state == USB_LINK_HM_IDGND_8500 && 397 (lsts == USB_LINK_STD_HOST_C_NS_8500 || 398 lsts == USB_LINK_STD_HOST_NC_8500)) 399 return 0; 400 401 if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8500 && 402 lsts == USB_LINK_STD_HOST_NC_8500) 403 return 0; 404 405 ab->previous_link_status_state = lsts; 406 407 switch (lsts) { 408 case USB_LINK_ACA_RID_B_8500: 409 event = UX500_MUSB_RIDB; 410 case USB_LINK_NOT_CONFIGURED_8500: 411 case USB_LINK_NOT_VALID_LINK_8500: 412 ab->mode = USB_IDLE; 413 ab->phy.otg->default_a = false; 414 ab->vbus_draw = 0; 415 if (event != UX500_MUSB_RIDB) 416 event = UX500_MUSB_NONE; 417 /* Fallback to default B_IDLE as nothing is connected */ 418 ab->phy.state = OTG_STATE_B_IDLE; 419 break; 420 421 case USB_LINK_ACA_RID_C_NM_8500: 422 case USB_LINK_ACA_RID_C_HS_8500: 423 case USB_LINK_ACA_RID_C_HS_CHIRP_8500: 424 event = UX500_MUSB_RIDC; 425 case USB_LINK_STD_HOST_NC_8500: 426 case USB_LINK_STD_HOST_C_NS_8500: 427 case USB_LINK_STD_HOST_C_S_8500: 428 case USB_LINK_HOST_CHG_NM_8500: 429 case USB_LINK_HOST_CHG_HS_8500: 430 case USB_LINK_HOST_CHG_HS_CHIRP_8500: 431 if (ab->mode == USB_IDLE) { 432 ab->mode = USB_PERIPHERAL; 433 ab8500_usb_peri_phy_en(ab); 434 atomic_notifier_call_chain(&ab->phy.notifier, 435 UX500_MUSB_PREPARE, &ab->vbus_draw); 436 } 437 if (event != UX500_MUSB_RIDC) 438 event = UX500_MUSB_VBUS; 439 break; 440 441 case USB_LINK_ACA_RID_A_8500: 442 event = UX500_MUSB_RIDA; 443 case USB_LINK_HM_IDGND_8500: 444 if (ab->mode == USB_IDLE) { 445 ab->mode = USB_HOST; 446 ab8500_usb_host_phy_en(ab); 447 atomic_notifier_call_chain(&ab->phy.notifier, 448 UX500_MUSB_PREPARE, &ab->vbus_draw); 449 } 450 ab->phy.otg->default_a = true; 451 if (event != UX500_MUSB_RIDA) 452 event = UX500_MUSB_ID; 453 atomic_notifier_call_chain(&ab->phy.notifier, 454 event, &ab->vbus_draw); 455 break; 456 457 case USB_LINK_DEDICATED_CHG_8500: 458 ab->mode = USB_DEDICATED_CHG; 459 event = UX500_MUSB_CHARGER; 460 atomic_notifier_call_chain(&ab->phy.notifier, 461 event, &ab->vbus_draw); 462 break; 463 464 case USB_LINK_RESERVED_8500: 465 break; 466 } 467 468 return 0; 469 } 470 471 /* 472 * Connection Sequence: 473 * 1. Link Status Interrupt 474 * 2. Enable AB clock 475 * 3. Enable AB regulators 476 * 4. Enable USB phy 477 * 5. Reset the musb controller 478 * 6. Switch the ULPI GPIO pins to fucntion mode 479 * 7. Enable the musb Peripheral5 clock 480 * 8. Restore MUSB context 481 */ 482 static int abx500_usb_link_status_update(struct ab8500_usb *ab) 483 { 484 u8 reg; 485 int ret = 0; 486 487 if (is_ab8500(ab->ab8500)) { 488 enum ab8500_usb_link_status lsts; 489 490 abx500_get_register_interruptible(ab->dev, 491 AB8500_USB, AB8500_USB_LINE_STAT_REG, ®); 492 lsts = (reg >> 3) & 0x0F; 493 ret = ab8500_usb_link_status_update(ab, lsts); 494 } else if (is_ab8505(ab->ab8500)) { 495 enum ab8505_usb_link_status lsts; 496 497 abx500_get_register_interruptible(ab->dev, 498 AB8500_USB, AB8505_USB_LINE_STAT_REG, ®); 499 lsts = (reg >> 3) & 0x1F; 500 ret = ab8505_usb_link_status_update(ab, lsts); 501 } 502 503 return ret; 504 } 505 506 /* 507 * Disconnection Sequence: 508 * 1. Disconect Interrupt 509 * 2. Disable regulators 510 * 3. Disable AB clock 511 * 4. Disable the Phy 512 * 5. Link Status Interrupt 513 * 6. Disable Musb Clock 514 */ 515 static irqreturn_t ab8500_usb_disconnect_irq(int irq, void *data) 516 { 517 struct ab8500_usb *ab = (struct ab8500_usb *) data; 518 enum usb_phy_events event = UX500_MUSB_NONE; 519 520 /* Link status will not be updated till phy is disabled. */ 521 if (ab->mode == USB_HOST) { 522 ab->phy.otg->default_a = false; 523 ab->vbus_draw = 0; 524 atomic_notifier_call_chain(&ab->phy.notifier, 525 event, &ab->vbus_draw); 526 ab8500_usb_host_phy_dis(ab); 527 ab->mode = USB_IDLE; 528 } 529 530 if (ab->mode == USB_PERIPHERAL) { 531 atomic_notifier_call_chain(&ab->phy.notifier, 532 event, &ab->vbus_draw); 533 ab8500_usb_peri_phy_dis(ab); 534 atomic_notifier_call_chain(&ab->phy.notifier, 535 UX500_MUSB_CLEAN, &ab->vbus_draw); 536 ab->mode = USB_IDLE; 537 ab->phy.otg->default_a = false; 538 ab->vbus_draw = 0; 539 } 540 541 if (is_ab8500_2p0(ab->ab8500)) { 542 if (ab->mode == USB_DEDICATED_CHG) { 543 ab8500_usb_wd_linkstatus(ab, 544 AB8500_BIT_PHY_CTRL_DEVICE_EN); 545 abx500_mask_and_set_register_interruptible(ab->dev, 546 AB8500_USB, AB8500_USB_PHY_CTRL_REG, 547 AB8500_BIT_PHY_CTRL_DEVICE_EN, 0); 548 } 549 } 550 551 return IRQ_HANDLED; 552 } 553 554 static irqreturn_t ab8500_usb_link_status_irq(int irq, void *data) 555 { 556 struct ab8500_usb *ab = (struct ab8500_usb *) data; 557 558 abx500_usb_link_status_update(ab); 559 560 return IRQ_HANDLED; 561 } 562 563 static void ab8500_usb_phy_disable_work(struct work_struct *work) 564 { 565 struct ab8500_usb *ab = container_of(work, struct ab8500_usb, 566 phy_dis_work); 567 568 if (!ab->phy.otg->host) 569 ab8500_usb_host_phy_dis(ab); 570 571 if (!ab->phy.otg->gadget) 572 ab8500_usb_peri_phy_dis(ab); 573 } 574 575 static unsigned ab8500_eyediagram_workaroud(struct ab8500_usb *ab, unsigned mA) 576 { 577 /* 578 * AB8500 V2 has eye diagram issues when drawing more than 100mA from 579 * VBUS. Set charging current to 100mA in case of standard host 580 */ 581 if (is_ab8500_2p0_or_earlier(ab->ab8500)) 582 if (mA > 100) 583 mA = 100; 584 585 return mA; 586 } 587 588 static int ab8500_usb_set_power(struct usb_phy *phy, unsigned mA) 589 { 590 struct ab8500_usb *ab; 591 592 if (!phy) 593 return -ENODEV; 594 595 ab = phy_to_ab(phy); 596 597 mA = ab8500_eyediagram_workaroud(ab, mA); 598 599 ab->vbus_draw = mA; 600 601 atomic_notifier_call_chain(&ab->phy.notifier, 602 UX500_MUSB_VBUS, &ab->vbus_draw); 603 604 return 0; 605 } 606 607 static int ab8500_usb_set_suspend(struct usb_phy *x, int suspend) 608 { 609 /* TODO */ 610 return 0; 611 } 612 613 static int ab8500_usb_set_peripheral(struct usb_otg *otg, 614 struct usb_gadget *gadget) 615 { 616 struct ab8500_usb *ab; 617 618 if (!otg) 619 return -ENODEV; 620 621 ab = phy_to_ab(otg->phy); 622 623 ab->phy.otg->gadget = gadget; 624 625 /* Some drivers call this function in atomic context. 626 * Do not update ab8500 registers directly till this 627 * is fixed. 628 */ 629 630 if ((ab->mode != USB_IDLE) && (!gadget)) { 631 ab->mode = USB_IDLE; 632 schedule_work(&ab->phy_dis_work); 633 } 634 635 return 0; 636 } 637 638 static int ab8500_usb_set_host(struct usb_otg *otg, struct usb_bus *host) 639 { 640 struct ab8500_usb *ab; 641 642 if (!otg) 643 return -ENODEV; 644 645 ab = phy_to_ab(otg->phy); 646 647 ab->phy.otg->host = host; 648 649 /* Some drivers call this function in atomic context. 650 * Do not update ab8500 registers directly till this 651 * is fixed. 652 */ 653 654 if ((ab->mode != USB_IDLE) && (!host)) { 655 ab->mode = USB_IDLE; 656 schedule_work(&ab->phy_dis_work); 657 } 658 659 return 0; 660 } 661 662 static int ab8500_usb_regulator_get(struct ab8500_usb *ab) 663 { 664 int err; 665 666 ab->v_ape = devm_regulator_get(ab->dev, "v-ape"); 667 if (IS_ERR(ab->v_ape)) { 668 dev_err(ab->dev, "Could not get v-ape supply\n"); 669 err = PTR_ERR(ab->v_ape); 670 return err; 671 } 672 673 ab->v_ulpi = devm_regulator_get(ab->dev, "vddulpivio18"); 674 if (IS_ERR(ab->v_ulpi)) { 675 dev_err(ab->dev, "Could not get vddulpivio18 supply\n"); 676 err = PTR_ERR(ab->v_ulpi); 677 return err; 678 } 679 680 ab->v_musb = devm_regulator_get(ab->dev, "musb_1v8"); 681 if (IS_ERR(ab->v_musb)) { 682 dev_err(ab->dev, "Could not get musb_1v8 supply\n"); 683 err = PTR_ERR(ab->v_musb); 684 return err; 685 } 686 687 return 0; 688 } 689 690 static int ab8500_usb_irq_setup(struct platform_device *pdev, 691 struct ab8500_usb *ab) 692 { 693 int err; 694 int irq; 695 696 irq = platform_get_irq_byname(pdev, "USB_LINK_STATUS"); 697 if (irq < 0) { 698 dev_err(&pdev->dev, "Link status irq not found\n"); 699 return irq; 700 } 701 err = devm_request_threaded_irq(&pdev->dev, irq, NULL, 702 ab8500_usb_link_status_irq, 703 IRQF_NO_SUSPEND | IRQF_SHARED, "usb-link-status", ab); 704 if (err < 0) { 705 dev_err(ab->dev, "request_irq failed for link status irq\n"); 706 return err; 707 } 708 709 irq = platform_get_irq_byname(pdev, "ID_WAKEUP_F"); 710 if (irq < 0) { 711 dev_err(&pdev->dev, "ID fall irq not found\n"); 712 return irq; 713 } 714 err = devm_request_threaded_irq(&pdev->dev, irq, NULL, 715 ab8500_usb_disconnect_irq, 716 IRQF_NO_SUSPEND | IRQF_SHARED, "usb-id-fall", ab); 717 if (err < 0) { 718 dev_err(ab->dev, "request_irq failed for ID fall irq\n"); 719 return err; 720 } 721 722 irq = platform_get_irq_byname(pdev, "VBUS_DET_F"); 723 if (irq < 0) { 724 dev_err(&pdev->dev, "VBUS fall irq not found\n"); 725 return irq; 726 } 727 err = devm_request_threaded_irq(&pdev->dev, irq, NULL, 728 ab8500_usb_disconnect_irq, 729 IRQF_NO_SUSPEND | IRQF_SHARED, "usb-vbus-fall", ab); 730 if (err < 0) { 731 dev_err(ab->dev, "request_irq failed for Vbus fall irq\n"); 732 return err; 733 } 734 735 return 0; 736 } 737 738 static int ab8500_usb_probe(struct platform_device *pdev) 739 { 740 struct ab8500_usb *ab; 741 struct ab8500 *ab8500; 742 struct usb_otg *otg; 743 int err; 744 int rev; 745 746 ab8500 = dev_get_drvdata(pdev->dev.parent); 747 rev = abx500_get_chip_id(&pdev->dev); 748 749 if (is_ab8500_1p1_or_earlier(ab8500)) { 750 dev_err(&pdev->dev, "Unsupported AB8500 chip rev=%d\n", rev); 751 return -ENODEV; 752 } 753 754 ab = devm_kzalloc(&pdev->dev, sizeof(*ab), GFP_KERNEL); 755 if (!ab) 756 return -ENOMEM; 757 758 otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL); 759 if (!otg) 760 return -ENOMEM; 761 762 ab->dev = &pdev->dev; 763 ab->ab8500 = ab8500; 764 ab->phy.dev = ab->dev; 765 ab->phy.otg = otg; 766 ab->phy.label = "ab8500"; 767 ab->phy.set_suspend = ab8500_usb_set_suspend; 768 ab->phy.set_power = ab8500_usb_set_power; 769 ab->phy.state = OTG_STATE_UNDEFINED; 770 771 otg->phy = &ab->phy; 772 otg->set_host = ab8500_usb_set_host; 773 otg->set_peripheral = ab8500_usb_set_peripheral; 774 775 platform_set_drvdata(pdev, ab); 776 777 ATOMIC_INIT_NOTIFIER_HEAD(&ab->phy.notifier); 778 779 /* all: Disable phy when called from set_host and set_peripheral */ 780 INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work); 781 782 err = ab8500_usb_regulator_get(ab); 783 if (err) 784 return err; 785 786 err = ab8500_usb_irq_setup(pdev, ab); 787 if (err < 0) 788 return err; 789 790 err = usb_add_phy(&ab->phy, USB_PHY_TYPE_USB2); 791 if (err) { 792 dev_err(&pdev->dev, "Can't register transceiver\n"); 793 return err; 794 } 795 796 /* Phy tuning values for AB8500 */ 797 if (!is_ab8500_2p0_or_earlier(ab->ab8500)) { 798 /* Enable the PBT/Bank 0x12 access */ 799 err = abx500_set_register_interruptible(ab->dev, 800 AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x01); 801 if (err < 0) 802 dev_err(ab->dev, "Failed to enable bank12 access err=%d\n", 803 err); 804 805 err = abx500_set_register_interruptible(ab->dev, 806 AB8500_DEBUG, AB8500_USB_PHY_TUNE1, 0xC8); 807 if (err < 0) 808 dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n", 809 err); 810 811 err = abx500_set_register_interruptible(ab->dev, 812 AB8500_DEBUG, AB8500_USB_PHY_TUNE2, 0x00); 813 if (err < 0) 814 dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n", 815 err); 816 817 err = abx500_set_register_interruptible(ab->dev, 818 AB8500_DEBUG, AB8500_USB_PHY_TUNE3, 0x78); 819 if (err < 0) 820 dev_err(ab->dev, "Failed to set PHY_TUNE3 regester err=%d\n", 821 err); 822 823 /* Switch to normal mode/disable Bank 0x12 access */ 824 err = abx500_set_register_interruptible(ab->dev, 825 AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x00); 826 if (err < 0) 827 dev_err(ab->dev, "Failed to switch bank12 access err=%d\n", 828 err); 829 } 830 831 /* Phy tuning values for AB8505 */ 832 if (is_ab8505(ab->ab8500)) { 833 /* Enable the PBT/Bank 0x12 access */ 834 err = abx500_mask_and_set_register_interruptible(ab->dev, 835 AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 836 0x01, 0x01); 837 if (err < 0) 838 dev_err(ab->dev, "Failed to enable bank12 access err=%d\n", 839 err); 840 841 err = abx500_mask_and_set_register_interruptible(ab->dev, 842 AB8500_DEBUG, AB8500_USB_PHY_TUNE1, 843 0xC8, 0xC8); 844 if (err < 0) 845 dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n", 846 err); 847 848 err = abx500_mask_and_set_register_interruptible(ab->dev, 849 AB8500_DEBUG, AB8500_USB_PHY_TUNE2, 850 0x60, 0x60); 851 if (err < 0) 852 dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n", 853 err); 854 855 err = abx500_mask_and_set_register_interruptible(ab->dev, 856 AB8500_DEBUG, AB8500_USB_PHY_TUNE3, 857 0xFC, 0x80); 858 859 if (err < 0) 860 dev_err(ab->dev, "Failed to set PHY_TUNE3 regester err=%d\n", 861 err); 862 863 /* Switch to normal mode/disable Bank 0x12 access */ 864 err = abx500_mask_and_set_register_interruptible(ab->dev, 865 AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 866 0x00, 0x00); 867 if (err < 0) 868 dev_err(ab->dev, "Failed to switch bank12 access err=%d\n", 869 err); 870 } 871 872 /* Needed to enable ID detection. */ 873 ab8500_usb_wd_workaround(ab); 874 875 abx500_usb_link_status_update(ab); 876 877 dev_info(&pdev->dev, "revision 0x%2x driver initialized\n", rev); 878 879 return 0; 880 } 881 882 static int ab8500_usb_remove(struct platform_device *pdev) 883 { 884 struct ab8500_usb *ab = platform_get_drvdata(pdev); 885 886 cancel_work_sync(&ab->phy_dis_work); 887 888 usb_remove_phy(&ab->phy); 889 890 if (ab->mode == USB_HOST) 891 ab8500_usb_host_phy_dis(ab); 892 else if (ab->mode == USB_PERIPHERAL) 893 ab8500_usb_peri_phy_dis(ab); 894 895 platform_set_drvdata(pdev, NULL); 896 897 return 0; 898 } 899 900 static struct platform_driver ab8500_usb_driver = { 901 .probe = ab8500_usb_probe, 902 .remove = ab8500_usb_remove, 903 .driver = { 904 .name = "ab8500-usb", 905 .owner = THIS_MODULE, 906 }, 907 }; 908 909 static int __init ab8500_usb_init(void) 910 { 911 return platform_driver_register(&ab8500_usb_driver); 912 } 913 subsys_initcall(ab8500_usb_init); 914 915 static void __exit ab8500_usb_exit(void) 916 { 917 platform_driver_unregister(&ab8500_usb_driver); 918 } 919 module_exit(ab8500_usb_exit); 920 921 MODULE_ALIAS("platform:ab8500_usb"); 922 MODULE_AUTHOR("ST-Ericsson AB"); 923 MODULE_DESCRIPTION("AB8500 usb transceiver driver"); 924 MODULE_LICENSE("GPL"); 925