1# 2# Physical Layer USB driver configuration 3# 4menu "USB Physical Layer drivers" 5 6config USB_PHY 7 def_bool n 8 9# 10# USB Transceiver Drivers 11# 12config AB8500_USB 13 tristate "AB8500 USB Transceiver Driver" 14 depends on AB8500_CORE 15 select USB_PHY 16 help 17 Enable this to support the USB OTG transceiver in AB8500 chip. 18 This transceiver supports high and full speed devices plus, 19 in host mode, low speed. 20 21config FSL_USB2_OTG 22 bool "Freescale USB OTG Transceiver Driver" 23 depends on USB_EHCI_FSL && USB_FSL_USB2 && PM_RUNTIME 24 select USB_OTG 25 select USB_PHY 26 help 27 Enable this to support Freescale USB OTG transceiver. 28 29config ISP1301_OMAP 30 tristate "Philips ISP1301 with OMAP OTG" 31 depends on I2C && ARCH_OMAP_OTG 32 select USB_PHY 33 help 34 If you say yes here you get support for the Philips ISP1301 35 USB-On-The-Go transceiver working with the OMAP OTG controller. 36 The ISP1301 is a full speed USB transceiver which is used in 37 products including H2, H3, and H4 development boards for Texas 38 Instruments OMAP processors. 39 40 This driver can also be built as a module. If so, the module 41 will be called isp1301_omap. 42 43config MV_U3D_PHY 44 bool "Marvell USB 3.0 PHY controller Driver" 45 depends on CPU_MMP3 46 select USB_PHY 47 help 48 Enable this to support Marvell USB 3.0 phy controller for Marvell 49 SoC. 50 51config NOP_USB_XCEIV 52 tristate "NOP USB Transceiver Driver" 53 select USB_PHY 54 help 55 This driver is to be used by all the usb transceiver which are either 56 built-in with usb ip or which are autonomous and doesn't require any 57 phy programming such as ISP1x04 etc. 58 59config OMAP_CONTROL_USB 60 tristate "OMAP CONTROL USB Driver" 61 depends on ARCH_OMAP2PLUS || COMPILE_TEST 62 help 63 Enable this to add support for the USB part present in the control 64 module. This driver has API to power on the USB2 PHY and to write to 65 the mailbox. The mailbox is present only in omap4 and the register to 66 power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an 67 additional register to power on USB3 PHY. 68 69config OMAP_USB2 70 tristate "OMAP USB2 PHY Driver" 71 depends on ARCH_OMAP2PLUS 72 select OMAP_CONTROL_USB 73 select USB_PHY 74 help 75 Enable this to support the transceiver that is part of SOC. This 76 driver takes care of all the PHY functionality apart from comparator. 77 The USB OTG controller communicates with the comparator using this 78 driver. 79 80config OMAP_USB3 81 tristate "OMAP USB3 PHY Driver" 82 depends on ARCH_OMAP2PLUS || COMPILE_TEST 83 select OMAP_CONTROL_USB 84 select USB_PHY 85 help 86 Enable this to support the USB3 PHY that is part of SOC. This 87 driver takes care of all the PHY functionality apart from comparator. 88 This driver interacts with the "OMAP Control USB Driver" to power 89 on/off the PHY. 90 91config AM335X_CONTROL_USB 92 tristate 93 94config AM335X_PHY_USB 95 tristate "AM335x USB PHY Driver" 96 select USB_PHY 97 select AM335X_CONTROL_USB 98 select NOP_USB_XCEIV 99 help 100 This driver provides PHY support for that phy which part for the 101 AM335x SoC. 102 103config SAMSUNG_USBPHY 104 tristate 105 help 106 Enable this to support Samsung USB phy helper driver for Samsung SoCs. 107 This driver provides common interface to interact, for Samsung USB 2.0 PHY 108 driver and later for Samsung USB 3.0 PHY driver. 109 110config SAMSUNG_USB2PHY 111 tristate "Samsung USB 2.0 PHY controller Driver" 112 select SAMSUNG_USBPHY 113 select USB_PHY 114 help 115 Enable this to support Samsung USB 2.0 (High Speed) PHY controller 116 driver for Samsung SoCs. 117 118config SAMSUNG_USB3PHY 119 tristate "Samsung USB 3.0 PHY controller Driver" 120 select SAMSUNG_USBPHY 121 select USB_PHY 122 help 123 Enable this to support Samsung USB 3.0 (Super Speed) phy controller 124 for samsung SoCs. 125 126config TWL4030_USB 127 tristate "TWL4030 USB Transceiver Driver" 128 depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS 129 select USB_PHY 130 help 131 Enable this to support the USB OTG transceiver on TWL4030 132 family chips (including the TWL5030 and TPS659x0 devices). 133 This transceiver supports high and full speed devices plus, 134 in host mode, low speed. 135 136config TWL6030_USB 137 tristate "TWL6030 USB Transceiver Driver" 138 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS 139 help 140 Enable this to support the USB OTG transceiver on TWL6030 141 family chips. This TWL6030 transceiver has the VBUS and ID GND 142 and OTG SRP events capabilities. For all other transceiver functionality 143 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs 144 are hooked to this driver through platform_data structure. 145 The definition of internal PHY APIs are in the mach-omap2 layer. 146 147config USB_GPIO_VBUS 148 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" 149 depends on GPIOLIB 150 select USB_PHY 151 help 152 Provides simple GPIO VBUS sensing for controllers with an 153 internal transceiver via the usb_phy interface, and 154 optionally control of a D+ pullup GPIO as well as a VBUS 155 current limit regulator. 156 157config USB_ISP1301 158 tristate "NXP ISP1301 USB transceiver support" 159 depends on USB || USB_GADGET 160 depends on I2C 161 select USB_PHY 162 help 163 Say Y here to add support for the NXP ISP1301 USB transceiver driver. 164 This chip is typically used as USB transceiver for USB host, gadget 165 and OTG drivers (to be selected separately). 166 167 To compile this driver as a module, choose M here: the 168 module will be called isp1301. 169 170config USB_MSM_OTG 171 tristate "OTG support for Qualcomm on-chip USB controller" 172 depends on (USB || USB_GADGET) && ARCH_MSM 173 select USB_PHY 174 help 175 Enable this to support the USB OTG transceiver on MSM chips. It 176 handles PHY initialization, clock management, and workarounds 177 required after resetting the hardware and power management. 178 This driver is required even for peripheral only or host only 179 mode configurations. 180 This driver is not supported on boards like trout which 181 has an external PHY. 182 183config USB_MV_OTG 184 tristate "Marvell USB OTG support" 185 depends on USB_EHCI_MV && USB_MV_UDC && PM_RUNTIME 186 select USB_OTG 187 select USB_PHY 188 help 189 Say Y here if you want to build Marvell USB OTG transciever 190 driver in kernel (including PXA and MMP series). This driver 191 implements role switch between EHCI host driver and gadget driver. 192 193 To compile this driver as a module, choose M here. 194 195config USB_MXS_PHY 196 tristate "Freescale MXS USB PHY support" 197 depends on ARCH_MXC || ARCH_MXS 198 select STMP_DEVICE 199 select USB_PHY 200 help 201 Enable this to support the Freescale MXS USB PHY. 202 203 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. 204 205config USB_RCAR_PHY 206 tristate "Renesas R-Car USB PHY support" 207 depends on USB || USB_GADGET 208 select USB_PHY 209 help 210 Say Y here to add support for the Renesas R-Car USB common PHY driver. 211 This chip is typically used as USB PHY for USB host, gadget. 212 This driver supports R8A7778 and R8A7779. 213 214 To compile this driver as a module, choose M here: the 215 module will be called phy-rcar-usb. 216 217config USB_ULPI 218 bool "Generic ULPI Transceiver Driver" 219 depends on ARM 220 help 221 Enable this to support ULPI connected USB OTG transceivers which 222 are likely found on embedded boards. 223 224config USB_ULPI_VIEWPORT 225 bool 226 depends on USB_ULPI 227 help 228 Provides read/write operations to the ULPI phy register set for 229 controllers with a viewport register (e.g. Chipidea/ARC controllers). 230 231endmenu 232