1# 2# Physical Layer USB driver configuration 3# 4menu "USB Physical Layer drivers" 5 6config USB_PHY 7 def_bool n 8 9# 10# USB Transceiver Drivers 11# 12config AB8500_USB 13 tristate "AB8500 USB Transceiver Driver" 14 depends on AB8500_CORE 15 select USB_PHY 16 help 17 Enable this to support the USB OTG transceiver in AB8500 chip. 18 This transceiver supports high and full speed devices plus, 19 in host mode, low speed. 20 21config FSL_USB2_OTG 22 bool "Freescale USB OTG Transceiver Driver" 23 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM 24 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 25 select USB_PHY 26 help 27 Enable this to support Freescale USB OTG transceiver. 28 29config ISP1301_OMAP 30 tristate "Philips ISP1301 with OMAP OTG" 31 depends on I2C && ARCH_OMAP_OTG 32 depends on USB 33 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 34 select USB_PHY 35 help 36 If you say yes here you get support for the Philips ISP1301 37 USB-On-The-Go transceiver working with the OMAP OTG controller. 38 The ISP1301 is a full speed USB transceiver which is used in 39 products including H2, H3, and H4 development boards for Texas 40 Instruments OMAP processors. 41 42 This driver can also be built as a module. If so, the module 43 will be called phy-isp1301-omap. 44 45config KEYSTONE_USB_PHY 46 tristate "Keystone USB PHY Driver" 47 depends on ARCH_KEYSTONE || COMPILE_TEST 48 depends on NOP_USB_XCEIV 49 help 50 Enable this to support Keystone USB phy. This driver provides 51 interface to interact with USB 2.0 and USB 3.0 PHY that is part 52 of the Keystone SOC. 53 54config NOP_USB_XCEIV 55 tristate "NOP USB Transceiver Driver" 56 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in 57 select USB_PHY 58 help 59 This driver is to be used by all the usb transceiver which are either 60 built-in with usb ip or which are autonomous and doesn't require any 61 phy programming such as ISP1x04 etc. 62 63config AM335X_CONTROL_USB 64 tristate 65 66config AM335X_PHY_USB 67 tristate "AM335x USB PHY Driver" 68 depends on ARM || COMPILE_TEST 69 depends on NOP_USB_XCEIV 70 select USB_PHY 71 select AM335X_CONTROL_USB 72 select USB_COMMON 73 help 74 This driver provides PHY support for that phy which part for the 75 AM335x SoC. 76 77config SAMSUNG_USBPHY 78 tristate 79 help 80 Enable this to support Samsung USB phy helper driver for Samsung SoCs. 81 This driver provides common interface to interact, for Samsung USB 2.0 PHY 82 driver and later for Samsung USB 3.0 PHY driver. 83 84config TWL6030_USB 85 tristate "TWL6030 USB Transceiver Driver" 86 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS 87 help 88 Enable this to support the USB OTG transceiver on TWL6030 89 family chips. This TWL6030 transceiver has the VBUS and ID GND 90 and OTG SRP events capabilities. For all other transceiver functionality 91 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs 92 are hooked to this driver through platform_data structure. 93 The definition of internal PHY APIs are in the mach-omap2 layer. 94 95config USB_GPIO_VBUS 96 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" 97 depends on GPIOLIB || COMPILE_TEST 98 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 99 select USB_PHY 100 help 101 Provides simple GPIO VBUS sensing for controllers with an 102 internal transceiver via the usb_phy interface, and 103 optionally control of a D+ pullup GPIO as well as a VBUS 104 current limit regulator. 105 106config OMAP_OTG 107 tristate "OMAP USB OTG controller driver" 108 depends on ARCH_OMAP_OTG && EXTCON 109 help 110 Enable this to support some transceivers on OMAP1 platforms. OTG 111 controller is needed to switch between host and peripheral modes. 112 113 This driver can also be built as a module. If so, the module 114 will be called phy-omap-otg. 115 116config TAHVO_USB 117 tristate "Tahvo USB transceiver driver" 118 depends on MFD_RETU && EXTCON 119 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 120 select USB_PHY 121 help 122 Enable this to support USB transceiver on Tahvo. This is used 123 at least on Nokia 770. 124 125config TAHVO_USB_HOST_BY_DEFAULT 126 depends on TAHVO_USB 127 bool "Device in USB host mode by default" 128 help 129 Say Y here, if you want the device to enter USB host mode 130 by default on bootup. 131 132config USB_ISP1301 133 tristate "NXP ISP1301 USB transceiver support" 134 depends on USB || USB_GADGET 135 depends on I2C 136 select USB_PHY 137 help 138 Say Y here to add support for the NXP ISP1301 USB transceiver driver. 139 This chip is typically used as USB transceiver for USB host, gadget 140 and OTG drivers (to be selected separately). 141 142 To compile this driver as a module, choose M here: the 143 module will be called phy-isp1301. 144 145config USB_MSM_OTG 146 tristate "Qualcomm on-chip USB OTG controller support" 147 depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST) 148 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 149 depends on RESET_CONTROLLER 150 depends on EXTCON 151 select USB_PHY 152 help 153 Enable this to support the USB OTG transceiver on Qualcomm chips. It 154 handles PHY initialization, clock management, and workarounds 155 required after resetting the hardware and power management. 156 This driver is required even for peripheral only or host only 157 mode configurations. 158 This driver is not supported on boards like trout which 159 has an external PHY. 160 161config USB_QCOM_8X16_PHY 162 tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support" 163 depends on ARCH_QCOM || COMPILE_TEST 164 depends on RESET_CONTROLLER && EXTCON 165 select USB_PHY 166 select USB_ULPI_VIEWPORT 167 help 168 Enable this to support the USB transceiver on Qualcomm 8x16 chipsets. 169 It handles PHY initialization, clock management, power management, 170 and workarounds required after resetting the hardware. 171 172 To compile this driver as a module, choose M here: the 173 module will be called phy-qcom-8x16-usb. 174 175config USB_MV_OTG 176 tristate "Marvell USB OTG support" 177 depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG 178 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 179 select USB_PHY 180 help 181 Say Y here if you want to build Marvell USB OTG transciever 182 driver in kernel (including PXA and MMP series). This driver 183 implements role switch between EHCI host driver and gadget driver. 184 185 To compile this driver as a module, choose M here. 186 187config USB_MXS_PHY 188 tristate "Freescale MXS USB PHY support" 189 depends on ARCH_MXC || ARCH_MXS 190 select STMP_DEVICE 191 select USB_PHY 192 help 193 Enable this to support the Freescale MXS USB PHY. 194 195 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. 196 197config USB_ULPI 198 bool "Generic ULPI Transceiver Driver" 199 depends on ARM || ARM64 200 select USB_ULPI_VIEWPORT 201 help 202 Enable this to support ULPI connected USB OTG transceivers which 203 are likely found on embedded boards. 204 205config USB_ULPI_VIEWPORT 206 bool 207 help 208 Provides read/write operations to the ULPI phy register set for 209 controllers with a viewport register (e.g. Chipidea/ARC controllers). 210 211endmenu 212