1# 2# Physical Layer USB driver configuration 3# 4menu "USB Physical Layer drivers" 5 6config USB_PHY 7 def_bool n 8 9# 10# USB Transceiver Drivers 11# 12config AB8500_USB 13 tristate "AB8500 USB Transceiver Driver" 14 depends on AB8500_CORE 15 select USB_PHY 16 help 17 Enable this to support the USB OTG transceiver in AB8500 chip. 18 This transceiver supports high and full speed devices plus, 19 in host mode, low speed. 20 21config FSL_USB2_OTG 22 bool "Freescale USB OTG Transceiver Driver" 23 depends on USB_EHCI_FSL && USB_FSL_USB2 && USB_OTG_FSM && PM 24 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 25 select USB_PHY 26 help 27 Enable this to support Freescale USB OTG transceiver. 28 29config ISP1301_OMAP 30 tristate "Philips ISP1301 with OMAP OTG" 31 depends on I2C && ARCH_OMAP_OTG 32 depends on USB 33 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 34 select USB_PHY 35 help 36 If you say yes here you get support for the Philips ISP1301 37 USB-On-The-Go transceiver working with the OMAP OTG controller. 38 The ISP1301 is a full speed USB transceiver which is used in 39 products including H2, H3, and H4 development boards for Texas 40 Instruments OMAP processors. 41 42 This driver can also be built as a module. If so, the module 43 will be called phy-isp1301-omap. 44 45config KEYSTONE_USB_PHY 46 tristate "Keystone USB PHY Driver" 47 depends on ARCH_KEYSTONE || COMPILE_TEST 48 depends on NOP_USB_XCEIV 49 help 50 Enable this to support Keystone USB phy. This driver provides 51 interface to interact with USB 2.0 and USB 3.0 PHY that is part 52 of the Keystone SOC. 53 54config NOP_USB_XCEIV 55 tristate "NOP USB Transceiver Driver" 56 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, NOP can't be built-in 57 select USB_PHY 58 help 59 This driver is to be used by all the usb transceiver which are either 60 built-in with usb ip or which are autonomous and doesn't require any 61 phy programming such as ISP1x04 etc. 62 63config AM335X_CONTROL_USB 64 tristate 65 66config AM335X_PHY_USB 67 tristate "AM335x USB PHY Driver" 68 depends on ARM || COMPILE_TEST 69 depends on NOP_USB_XCEIV 70 select USB_PHY 71 select AM335X_CONTROL_USB 72 select USB_COMMON 73 help 74 This driver provides PHY support for that phy which part for the 75 AM335x SoC. 76 77config SAMSUNG_USBPHY 78 tristate 79 help 80 Enable this to support Samsung USB phy helper driver for Samsung SoCs. 81 This driver provides common interface to interact, for Samsung USB 2.0 PHY 82 driver and later for Samsung USB 3.0 PHY driver. 83 84config TWL6030_USB 85 tristate "TWL6030 USB Transceiver Driver" 86 depends on TWL4030_CORE && OMAP_USB2 && USB_MUSB_OMAP2PLUS 87 depends on OF 88 help 89 Enable this to support the USB OTG transceiver on TWL6030 90 family chips. This TWL6030 transceiver has the VBUS and ID GND 91 and OTG SRP events capabilities. For all other transceiver functionality 92 UTMI PHY is embedded in OMAP4430. The internal PHY configurations APIs 93 are hooked to this driver through platform_data structure. 94 The definition of internal PHY APIs are in the mach-omap2 layer. 95 96config USB_GPIO_VBUS 97 tristate "GPIO based peripheral-only VBUS sensing 'transceiver'" 98 depends on GPIOLIB || COMPILE_TEST 99 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 100 select USB_PHY 101 help 102 Provides simple GPIO VBUS sensing for controllers with an 103 internal transceiver via the usb_phy interface, and 104 optionally control of a D+ pullup GPIO as well as a VBUS 105 current limit regulator. 106 107config OMAP_OTG 108 tristate "OMAP USB OTG controller driver" 109 depends on ARCH_OMAP_OTG && EXTCON 110 help 111 Enable this to support some transceivers on OMAP1 platforms. OTG 112 controller is needed to switch between host and peripheral modes. 113 114 This driver can also be built as a module. If so, the module 115 will be called phy-omap-otg. 116 117config TAHVO_USB 118 tristate "Tahvo USB transceiver driver" 119 depends on MFD_RETU && EXTCON 120 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 121 select USB_PHY 122 help 123 Enable this to support USB transceiver on Tahvo. This is used 124 at least on Nokia 770. 125 126config TAHVO_USB_HOST_BY_DEFAULT 127 depends on TAHVO_USB 128 bool "Device in USB host mode by default" 129 help 130 Say Y here, if you want the device to enter USB host mode 131 by default on bootup. 132 133config USB_ISP1301 134 tristate "NXP ISP1301 USB transceiver support" 135 depends on USB || USB_GADGET 136 depends on I2C 137 select USB_PHY 138 help 139 Say Y here to add support for the NXP ISP1301 USB transceiver driver. 140 This chip is typically used as USB transceiver for USB host, gadget 141 and OTG drivers (to be selected separately). 142 143 To compile this driver as a module, choose M here: the 144 module will be called phy-isp1301. 145 146config USB_MSM_OTG 147 tristate "Qualcomm on-chip USB OTG controller support" 148 depends on (USB || USB_GADGET) && (ARCH_QCOM || COMPILE_TEST) 149 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 150 depends on RESET_CONTROLLER 151 depends on EXTCON 152 select USB_PHY 153 help 154 Enable this to support the USB OTG transceiver on Qualcomm chips. It 155 handles PHY initialization, clock management, and workarounds 156 required after resetting the hardware and power management. 157 This driver is required even for peripheral only or host only 158 mode configurations. 159 This driver is not supported on boards like trout which 160 has an external PHY. 161 162config USB_QCOM_8X16_PHY 163 tristate "Qualcomm APQ8016/MSM8916 on-chip USB PHY controller support" 164 depends on ARCH_QCOM || COMPILE_TEST 165 depends on RESET_CONTROLLER && EXTCON 166 select USB_PHY 167 select USB_ULPI_VIEWPORT 168 help 169 Enable this to support the USB transceiver on Qualcomm 8x16 chipsets. 170 It handles PHY initialization, clock management, power management, 171 and workarounds required after resetting the hardware. 172 173 To compile this driver as a module, choose M here: the 174 module will be called phy-qcom-8x16-usb. 175 176config USB_MV_OTG 177 tristate "Marvell USB OTG support" 178 depends on USB_EHCI_MV && USB_MV_UDC && PM && USB_OTG 179 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't be 'y' 180 select USB_PHY 181 help 182 Say Y here if you want to build Marvell USB OTG transciever 183 driver in kernel (including PXA and MMP series). This driver 184 implements role switch between EHCI host driver and gadget driver. 185 186 To compile this driver as a module, choose M here. 187 188config USB_MXS_PHY 189 tristate "Freescale MXS USB PHY support" 190 depends on ARCH_MXC || ARCH_MXS 191 select STMP_DEVICE 192 select USB_PHY 193 help 194 Enable this to support the Freescale MXS USB PHY. 195 196 MXS Phy is used by some of the i.MX SoCs, for example imx23/28/6x. 197 198config USB_ULPI 199 bool "Generic ULPI Transceiver Driver" 200 depends on ARM || ARM64 201 select USB_ULPI_VIEWPORT 202 help 203 Enable this to support ULPI connected USB OTG transceivers which 204 are likely found on embedded boards. 205 206config USB_ULPI_VIEWPORT 207 bool 208 help 209 Provides read/write operations to the ULPI phy register set for 210 controllers with a viewport register (e.g. Chipidea/ARC controllers). 211 212endmenu 213