1 /* SPDX-License-Identifier: GPL-2.0 */ 2 /* 3 * MUSB OTG driver defines 4 * 5 * Copyright 2005 Mentor Graphics Corporation 6 * Copyright (C) 2005-2006 by Texas Instruments 7 * Copyright (C) 2006-2007 Nokia Corporation 8 */ 9 10 #ifndef __MUSB_CORE_H__ 11 #define __MUSB_CORE_H__ 12 13 #include <linux/slab.h> 14 #include <linux/list.h> 15 #include <linux/interrupt.h> 16 #include <linux/errno.h> 17 #include <linux/timer.h> 18 #include <linux/device.h> 19 #include <linux/usb/ch9.h> 20 #include <linux/usb/gadget.h> 21 #include <linux/usb.h> 22 #include <linux/usb/otg.h> 23 #include <linux/usb/musb.h> 24 #include <linux/phy/phy.h> 25 #include <linux/workqueue.h> 26 27 struct musb; 28 struct musb_hw_ep; 29 struct musb_ep; 30 struct musb_qh; 31 32 /* Helper defines for struct musb->hwvers */ 33 #define MUSB_HWVERS_MAJOR(x) ((x >> 10) & 0x1f) 34 #define MUSB_HWVERS_MINOR(x) (x & 0x3ff) 35 #define MUSB_HWVERS_RC 0x8000 36 #define MUSB_HWVERS_1300 0x52C 37 #define MUSB_HWVERS_1400 0x590 38 #define MUSB_HWVERS_1800 0x720 39 #define MUSB_HWVERS_1900 0x784 40 #define MUSB_HWVERS_2000 0x800 41 42 #include "musb_debug.h" 43 #include "musb_dma.h" 44 45 #include "musb_io.h" 46 47 #include "musb_gadget.h" 48 #include <linux/usb/hcd.h> 49 #include "musb_host.h" 50 51 /* NOTE: otg and peripheral-only state machines start at B_IDLE. 52 * OTG or host-only go to A_IDLE when ID is sensed. 53 */ 54 #define is_peripheral_active(m) (!(m)->is_host) 55 #define is_host_active(m) ((m)->is_host) 56 57 /****************************** CONSTANTS ********************************/ 58 59 #ifndef MUSB_C_NUM_EPS 60 #define MUSB_C_NUM_EPS ((u8)16) 61 #endif 62 63 #ifndef MUSB_MAX_END0_PACKET 64 #define MUSB_MAX_END0_PACKET ((u16)MUSB_EP0_FIFOSIZE) 65 #endif 66 67 /* host side ep0 states */ 68 enum musb_h_ep0_state { 69 MUSB_EP0_IDLE, 70 MUSB_EP0_START, /* expect ack of setup */ 71 MUSB_EP0_IN, /* expect IN DATA */ 72 MUSB_EP0_OUT, /* expect ack of OUT DATA */ 73 MUSB_EP0_STATUS, /* expect ack of STATUS */ 74 } __attribute__ ((packed)); 75 76 /* peripheral side ep0 states */ 77 enum musb_g_ep0_state { 78 MUSB_EP0_STAGE_IDLE, /* idle, waiting for SETUP */ 79 MUSB_EP0_STAGE_SETUP, /* received SETUP */ 80 MUSB_EP0_STAGE_TX, /* IN data */ 81 MUSB_EP0_STAGE_RX, /* OUT data */ 82 MUSB_EP0_STAGE_STATUSIN, /* (after OUT data) */ 83 MUSB_EP0_STAGE_STATUSOUT, /* (after IN data) */ 84 MUSB_EP0_STAGE_ACKWAIT, /* after zlp, before statusin */ 85 } __attribute__ ((packed)); 86 87 /* 88 * OTG protocol constants. See USB OTG 1.3 spec, 89 * sections 5.5 "Device Timings" and 6.6.5 "Timers". 90 */ 91 #define OTG_TIME_A_WAIT_VRISE 100 /* msec (max) */ 92 #define OTG_TIME_A_WAIT_BCON 1100 /* min 1 second */ 93 #define OTG_TIME_A_AIDL_BDIS 200 /* min 200 msec */ 94 #define OTG_TIME_B_ASE0_BRST 100 /* min 3.125 ms */ 95 96 /****************************** FUNCTIONS ********************************/ 97 98 #define MUSB_HST_MODE(_musb)\ 99 { (_musb)->is_host = true; } 100 #define MUSB_DEV_MODE(_musb) \ 101 { (_musb)->is_host = false; } 102 103 #define test_devctl_hst_mode(_x) \ 104 (musb_readb((_x)->mregs, MUSB_DEVCTL)&MUSB_DEVCTL_HM) 105 106 #define MUSB_MODE(musb) ((musb)->is_host ? "Host" : "Peripheral") 107 108 /******************************** TYPES *************************************/ 109 110 struct musb_io; 111 112 /** 113 * struct musb_platform_ops - Operations passed to musb_core by HW glue layer 114 * @quirks: flags for platform specific quirks 115 * @enable: enable device 116 * @disable: disable device 117 * @ep_offset: returns the end point offset 118 * @ep_select: selects the specified end point 119 * @fifo_mode: sets the fifo mode 120 * @fifo_offset: returns the fifo offset 121 * @readb: read 8 bits 122 * @writeb: write 8 bits 123 * @clearb: could be clear-on-readb or W1C 124 * @readw: read 16 bits 125 * @writew: write 16 bits 126 * @clearw: could be clear-on-readw or W1C 127 * @read_fifo: reads the fifo 128 * @write_fifo: writes to fifo 129 * @get_toggle: platform specific get toggle function 130 * @set_toggle: platform specific set toggle function 131 * @dma_init: platform specific dma init function 132 * @dma_exit: platform specific dma exit function 133 * @init: turns on clocks, sets up platform-specific registers, etc 134 * @exit: undoes @init 135 * @set_mode: forcefully changes operating mode 136 * @try_idle: tries to idle the IP 137 * @recover: platform-specific babble recovery 138 * @vbus_status: returns vbus status if possible 139 * @set_vbus: forces vbus status 140 * @pre_root_reset_end: called before the root usb port reset flag gets cleared 141 * @post_root_reset_end: called after the root usb port reset flag gets cleared 142 * @phy_callback: optional callback function for the phy to call 143 */ 144 struct musb_platform_ops { 145 146 #define MUSB_G_NO_SKB_RESERVE BIT(9) 147 #define MUSB_DA8XX BIT(8) 148 #define MUSB_PRESERVE_SESSION BIT(7) 149 #define MUSB_DMA_UX500 BIT(6) 150 #define MUSB_DMA_CPPI41 BIT(5) 151 #define MUSB_DMA_CPPI BIT(4) 152 #define MUSB_DMA_TUSB_OMAP BIT(3) 153 #define MUSB_DMA_INVENTRA BIT(2) 154 #define MUSB_IN_TUSB BIT(1) 155 #define MUSB_INDEXED_EP BIT(0) 156 u32 quirks; 157 158 int (*init)(struct musb *musb); 159 int (*exit)(struct musb *musb); 160 161 void (*enable)(struct musb *musb); 162 void (*disable)(struct musb *musb); 163 164 u32 (*ep_offset)(u8 epnum, u16 offset); 165 void (*ep_select)(void __iomem *mbase, u8 epnum); 166 u16 fifo_mode; 167 u32 (*fifo_offset)(u8 epnum); 168 u32 (*busctl_offset)(u8 epnum, u16 offset); 169 u8 (*readb)(void __iomem *addr, u32 offset); 170 void (*writeb)(void __iomem *addr, u32 offset, u8 data); 171 u8 (*clearb)(void __iomem *addr, u32 offset); 172 u16 (*readw)(void __iomem *addr, u32 offset); 173 void (*writew)(void __iomem *addr, u32 offset, u16 data); 174 u16 (*clearw)(void __iomem *addr, u32 offset); 175 void (*read_fifo)(struct musb_hw_ep *hw_ep, u16 len, u8 *buf); 176 void (*write_fifo)(struct musb_hw_ep *hw_ep, u16 len, const u8 *buf); 177 u16 (*get_toggle)(struct musb_qh *qh, int is_out); 178 u16 (*set_toggle)(struct musb_qh *qh, int is_out, struct urb *urb); 179 struct dma_controller * 180 (*dma_init) (struct musb *musb, void __iomem *base); 181 void (*dma_exit)(struct dma_controller *c); 182 int (*set_mode)(struct musb *musb, u8 mode); 183 void (*try_idle)(struct musb *musb, unsigned long timeout); 184 int (*recover)(struct musb *musb); 185 186 int (*vbus_status)(struct musb *musb); 187 void (*set_vbus)(struct musb *musb, int on); 188 189 void (*pre_root_reset_end)(struct musb *musb); 190 void (*post_root_reset_end)(struct musb *musb); 191 int (*phy_callback)(enum musb_vbus_id_status status); 192 void (*clear_ep_rxintr)(struct musb *musb, int epnum); 193 }; 194 195 /* 196 * struct musb_hw_ep - endpoint hardware (bidirectional) 197 * 198 * Ordered slightly for better cacheline locality. 199 */ 200 struct musb_hw_ep { 201 struct musb *musb; 202 void __iomem *fifo; 203 void __iomem *regs; 204 205 #if IS_ENABLED(CONFIG_USB_MUSB_TUSB6010) 206 void __iomem *conf; 207 #endif 208 209 /* index in musb->endpoints[] */ 210 u8 epnum; 211 212 /* hardware configuration, possibly dynamic */ 213 bool is_shared_fifo; 214 bool tx_double_buffered; 215 bool rx_double_buffered; 216 u16 max_packet_sz_tx; 217 u16 max_packet_sz_rx; 218 219 struct dma_channel *tx_channel; 220 struct dma_channel *rx_channel; 221 222 #if IS_ENABLED(CONFIG_USB_MUSB_TUSB6010) 223 /* TUSB has "asynchronous" and "synchronous" dma modes */ 224 dma_addr_t fifo_async; 225 dma_addr_t fifo_sync; 226 void __iomem *fifo_sync_va; 227 #endif 228 229 /* currently scheduled peripheral endpoint */ 230 struct musb_qh *in_qh; 231 struct musb_qh *out_qh; 232 233 u8 rx_reinit; 234 u8 tx_reinit; 235 236 /* peripheral side */ 237 struct musb_ep ep_in; /* TX */ 238 struct musb_ep ep_out; /* RX */ 239 }; 240 241 static inline struct musb_request *next_in_request(struct musb_hw_ep *hw_ep) 242 { 243 return next_request(&hw_ep->ep_in); 244 } 245 246 static inline struct musb_request *next_out_request(struct musb_hw_ep *hw_ep) 247 { 248 return next_request(&hw_ep->ep_out); 249 } 250 251 struct musb_csr_regs { 252 /* FIFO registers */ 253 u16 txmaxp, txcsr, rxmaxp, rxcsr; 254 u16 rxfifoadd, txfifoadd; 255 u8 txtype, txinterval, rxtype, rxinterval; 256 u8 rxfifosz, txfifosz; 257 u8 txfunaddr, txhubaddr, txhubport; 258 u8 rxfunaddr, rxhubaddr, rxhubport; 259 }; 260 261 struct musb_context_registers { 262 263 u8 power; 264 u8 intrusbe; 265 u16 frame; 266 u8 index, testmode; 267 268 u8 devctl, busctl, misc; 269 u32 otg_interfsel; 270 271 struct musb_csr_regs index_regs[MUSB_C_NUM_EPS]; 272 }; 273 274 /* 275 * struct musb - Driver instance data. 276 */ 277 struct musb { 278 /* device lock */ 279 spinlock_t lock; 280 spinlock_t list_lock; /* resume work list lock */ 281 282 struct musb_io io; 283 const struct musb_platform_ops *ops; 284 struct musb_context_registers context; 285 286 irqreturn_t (*isr)(int, void *); 287 struct delayed_work irq_work; 288 struct delayed_work deassert_reset_work; 289 struct delayed_work finish_resume_work; 290 struct delayed_work gadget_work; 291 u16 hwvers; 292 293 u16 intrrxe; 294 u16 intrtxe; 295 /* this hub status bit is reserved by USB 2.0 and not seen by usbcore */ 296 #define MUSB_PORT_STAT_RESUME (1 << 31) 297 298 u32 port1_status; 299 300 unsigned long rh_timer; 301 302 enum musb_h_ep0_state ep0_stage; 303 304 /* bulk traffic normally dedicates endpoint hardware, and each 305 * direction has its own ring of host side endpoints. 306 * we try to progress the transfer at the head of each endpoint's 307 * queue until it completes or NAKs too much; then we try the next 308 * endpoint. 309 */ 310 struct musb_hw_ep *bulk_ep; 311 312 struct list_head control; /* of musb_qh */ 313 struct list_head in_bulk; /* of musb_qh */ 314 struct list_head out_bulk; /* of musb_qh */ 315 struct list_head pending_list; /* pending work list */ 316 317 struct timer_list otg_timer; 318 struct timer_list dev_timer; 319 struct notifier_block nb; 320 321 struct dma_controller *dma_controller; 322 323 struct device *controller; 324 void __iomem *ctrl_base; 325 void __iomem *mregs; 326 327 #if IS_ENABLED(CONFIG_USB_MUSB_TUSB6010) 328 dma_addr_t async; 329 dma_addr_t sync; 330 void __iomem *sync_va; 331 u8 tusb_revision; 332 #endif 333 334 /* passed down from chip/board specific irq handlers */ 335 u8 int_usb; 336 u16 int_rx; 337 u16 int_tx; 338 339 struct usb_phy *xceiv; 340 struct phy *phy; 341 342 enum usb_otg_state otg_state; 343 344 int nIrq; 345 unsigned irq_wake:1; 346 347 struct musb_hw_ep endpoints[MUSB_C_NUM_EPS]; 348 #define control_ep endpoints 349 350 #define VBUSERR_RETRY_COUNT 3 351 u16 vbuserr_retry; 352 u16 epmask; 353 u8 nr_endpoints; 354 355 u8 min_power; /* vbus for periph, in mA/2 */ 356 357 enum musb_mode port_mode; 358 bool session; 359 unsigned long quirk_retries; 360 bool is_host; 361 362 int a_wait_bcon; /* VBUS timeout in msecs */ 363 unsigned long idle_timeout; /* Next timeout in jiffies */ 364 365 unsigned is_initialized:1; 366 unsigned is_runtime_suspended:1; 367 368 /* active means connected and not suspended */ 369 unsigned is_active:1; 370 371 unsigned is_multipoint:1; 372 373 unsigned hb_iso_rx:1; /* high bandwidth iso rx? */ 374 unsigned hb_iso_tx:1; /* high bandwidth iso tx? */ 375 unsigned dyn_fifo:1; /* dynamic FIFO supported? */ 376 377 unsigned bulk_split:1; 378 #define can_bulk_split(musb, type) \ 379 (((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_split) 380 381 unsigned bulk_combine:1; 382 #define can_bulk_combine(musb, type) \ 383 (((type) == USB_ENDPOINT_XFER_BULK) && (musb)->bulk_combine) 384 385 /* is_suspended means USB B_PERIPHERAL suspend */ 386 unsigned is_suspended:1; 387 388 /* may_wakeup means remote wakeup is enabled */ 389 unsigned may_wakeup:1; 390 391 /* is_self_powered is reported in device status and the 392 * config descriptor. is_bus_powered means B_PERIPHERAL 393 * draws some VBUS current; both can be true. 394 */ 395 unsigned is_self_powered:1; 396 unsigned is_bus_powered:1; 397 398 unsigned set_address:1; 399 unsigned test_mode:1; 400 unsigned softconnect:1; 401 402 unsigned flush_irq_work:1; 403 404 u8 address; 405 u8 test_mode_nr; 406 u16 ackpend; /* ep0 */ 407 enum musb_g_ep0_state ep0_state; 408 struct usb_gadget g; /* the gadget */ 409 struct usb_gadget_driver *gadget_driver; /* its driver */ 410 struct usb_hcd *hcd; /* the usb hcd */ 411 412 const struct musb_hdrc_config *config; 413 414 int xceiv_old_state; 415 #ifdef CONFIG_DEBUG_FS 416 struct dentry *debugfs_root; 417 #endif 418 }; 419 420 /* This must be included after struct musb is defined */ 421 #include "musb_regs.h" 422 423 static inline struct musb *gadget_to_musb(struct usb_gadget *g) 424 { 425 return container_of(g, struct musb, g); 426 } 427 428 static inline char *musb_ep_xfertype_string(u8 type) 429 { 430 char *s; 431 432 switch (type) { 433 case USB_ENDPOINT_XFER_CONTROL: 434 s = "ctrl"; 435 break; 436 case USB_ENDPOINT_XFER_ISOC: 437 s = "iso"; 438 break; 439 case USB_ENDPOINT_XFER_BULK: 440 s = "bulk"; 441 break; 442 case USB_ENDPOINT_XFER_INT: 443 s = "int"; 444 break; 445 default: 446 s = ""; 447 break; 448 } 449 return s; 450 } 451 452 static inline int musb_read_fifosize(struct musb *musb, 453 struct musb_hw_ep *hw_ep, u8 epnum) 454 { 455 void __iomem *mbase = musb->mregs; 456 u8 reg = 0; 457 458 /* read from core using indexed model */ 459 reg = musb_readb(mbase, musb->io.ep_offset(epnum, MUSB_FIFOSIZE)); 460 /* 0's returned when no more endpoints */ 461 if (!reg) 462 return -ENODEV; 463 464 musb->nr_endpoints++; 465 musb->epmask |= (1 << epnum); 466 467 hw_ep->max_packet_sz_tx = 1 << (reg & 0x0f); 468 469 /* shared TX/RX FIFO? */ 470 if ((reg & 0xf0) == 0xf0) { 471 hw_ep->max_packet_sz_rx = hw_ep->max_packet_sz_tx; 472 hw_ep->is_shared_fifo = true; 473 return 0; 474 } else { 475 hw_ep->max_packet_sz_rx = 1 << ((reg & 0xf0) >> 4); 476 hw_ep->is_shared_fifo = false; 477 } 478 479 return 0; 480 } 481 482 static inline void musb_configure_ep0(struct musb *musb) 483 { 484 musb->endpoints[0].max_packet_sz_tx = MUSB_EP0_FIFOSIZE; 485 musb->endpoints[0].max_packet_sz_rx = MUSB_EP0_FIFOSIZE; 486 musb->endpoints[0].is_shared_fifo = true; 487 } 488 489 /***************************** Glue it together *****************************/ 490 491 extern const char musb_driver_name[]; 492 493 extern void musb_stop(struct musb *musb); 494 extern void musb_start(struct musb *musb); 495 496 extern void musb_write_fifo(struct musb_hw_ep *ep, u16 len, const u8 *src); 497 extern void musb_read_fifo(struct musb_hw_ep *ep, u16 len, u8 *dst); 498 499 extern int musb_set_host(struct musb *musb); 500 extern int musb_set_peripheral(struct musb *musb); 501 502 extern void musb_load_testpacket(struct musb *); 503 504 extern irqreturn_t musb_interrupt(struct musb *); 505 506 extern void musb_hnp_stop(struct musb *musb); 507 508 int musb_queue_resume_work(struct musb *musb, 509 int (*callback)(struct musb *musb, void *data), 510 void *data); 511 512 static inline void musb_platform_set_vbus(struct musb *musb, int is_on) 513 { 514 if (musb->ops->set_vbus) 515 musb->ops->set_vbus(musb, is_on); 516 } 517 518 static inline void musb_platform_enable(struct musb *musb) 519 { 520 if (musb->ops->enable) 521 musb->ops->enable(musb); 522 } 523 524 static inline void musb_platform_disable(struct musb *musb) 525 { 526 if (musb->ops->disable) 527 musb->ops->disable(musb); 528 } 529 530 static inline int musb_platform_set_mode(struct musb *musb, u8 mode) 531 { 532 if (!musb->ops->set_mode) 533 return 0; 534 535 return musb->ops->set_mode(musb, mode); 536 } 537 538 static inline void musb_platform_try_idle(struct musb *musb, 539 unsigned long timeout) 540 { 541 if (musb->ops->try_idle) 542 musb->ops->try_idle(musb, timeout); 543 } 544 545 static inline int musb_platform_recover(struct musb *musb) 546 { 547 if (!musb->ops->recover) 548 return 0; 549 550 return musb->ops->recover(musb); 551 } 552 553 static inline int musb_platform_get_vbus_status(struct musb *musb) 554 { 555 if (!musb->ops->vbus_status) 556 return -EINVAL; 557 558 return musb->ops->vbus_status(musb); 559 } 560 561 static inline int musb_platform_init(struct musb *musb) 562 { 563 if (!musb->ops->init) 564 return -EINVAL; 565 566 return musb->ops->init(musb); 567 } 568 569 static inline int musb_platform_exit(struct musb *musb) 570 { 571 if (!musb->ops->exit) 572 return -EINVAL; 573 574 return musb->ops->exit(musb); 575 } 576 577 static inline void musb_platform_pre_root_reset_end(struct musb *musb) 578 { 579 if (musb->ops->pre_root_reset_end) 580 musb->ops->pre_root_reset_end(musb); 581 } 582 583 static inline void musb_platform_post_root_reset_end(struct musb *musb) 584 { 585 if (musb->ops->post_root_reset_end) 586 musb->ops->post_root_reset_end(musb); 587 } 588 589 static inline void musb_platform_clear_ep_rxintr(struct musb *musb, int epnum) 590 { 591 if (musb->ops->clear_ep_rxintr) 592 musb->ops->clear_ep_rxintr(musb, epnum); 593 } 594 595 static inline void musb_set_state(struct musb *musb, 596 enum usb_otg_state otg_state) 597 { 598 if (musb->xceiv) 599 musb->xceiv->otg->state = otg_state; 600 else 601 musb->otg_state = otg_state; 602 } 603 604 static inline enum usb_otg_state musb_get_state(struct musb *musb) 605 { 606 if (musb->xceiv) 607 return musb->xceiv->otg->state; 608 609 return musb->otg_state; 610 } 611 612 static inline const char *musb_otg_state_string(struct musb *musb) 613 { 614 return usb_otg_state_string(musb_get_state(musb)); 615 } 616 617 /* 618 * gets the "dr_mode" property from DT and converts it into musb_mode 619 * if the property is not found or not recognized returns MUSB_OTG 620 */ 621 extern enum musb_mode musb_get_mode(struct device *dev); 622 623 #endif /* __MUSB_CORE_H__ */ 624