1 /* 2 * MUSB OTG driver core code 3 * 4 * Copyright 2005 Mentor Graphics Corporation 5 * Copyright (C) 2005-2006 by Texas Instruments 6 * Copyright (C) 2006-2007 Nokia Corporation 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License 10 * version 2 as published by the Free Software Foundation. 11 * 12 * This program is distributed in the hope that it will be useful, but 13 * WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU 15 * General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 20 * 02110-1301 USA 21 * 22 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED 23 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 24 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 25 * NO EVENT SHALL THE AUTHORS BE LIABLE FOR ANY DIRECT, INDIRECT, 26 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 27 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF 28 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON 29 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 30 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 31 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 32 * 33 */ 34 35 /* 36 * Inventra (Multipoint) Dual-Role Controller Driver for Linux. 37 * 38 * This consists of a Host Controller Driver (HCD) and a peripheral 39 * controller driver implementing the "Gadget" API; OTG support is 40 * in the works. These are normal Linux-USB controller drivers which 41 * use IRQs and have no dedicated thread. 42 * 43 * This version of the driver has only been used with products from 44 * Texas Instruments. Those products integrate the Inventra logic 45 * with other DMA, IRQ, and bus modules, as well as other logic that 46 * needs to be reflected in this driver. 47 * 48 * 49 * NOTE: the original Mentor code here was pretty much a collection 50 * of mechanisms that don't seem to have been fully integrated/working 51 * for *any* Linux kernel version. This version aims at Linux 2.6.now, 52 * Key open issues include: 53 * 54 * - Lack of host-side transaction scheduling, for all transfer types. 55 * The hardware doesn't do it; instead, software must. 56 * 57 * This is not an issue for OTG devices that don't support external 58 * hubs, but for more "normal" USB hosts it's a user issue that the 59 * "multipoint" support doesn't scale in the expected ways. That 60 * includes DaVinci EVM in a common non-OTG mode. 61 * 62 * * Control and bulk use dedicated endpoints, and there's as 63 * yet no mechanism to either (a) reclaim the hardware when 64 * peripherals are NAKing, which gets complicated with bulk 65 * endpoints, or (b) use more than a single bulk endpoint in 66 * each direction. 67 * 68 * RESULT: one device may be perceived as blocking another one. 69 * 70 * * Interrupt and isochronous will dynamically allocate endpoint 71 * hardware, but (a) there's no record keeping for bandwidth; 72 * (b) in the common case that few endpoints are available, there 73 * is no mechanism to reuse endpoints to talk to multiple devices. 74 * 75 * RESULT: At one extreme, bandwidth can be overcommitted in 76 * some hardware configurations, no faults will be reported. 77 * At the other extreme, the bandwidth capabilities which do 78 * exist tend to be severely undercommitted. You can't yet hook 79 * up both a keyboard and a mouse to an external USB hub. 80 */ 81 82 /* 83 * This gets many kinds of configuration information: 84 * - Kconfig for everything user-configurable 85 * - platform_device for addressing, irq, and platform_data 86 * - platform_data is mostly for board-specific informarion 87 * (plus recentrly, SOC or family details) 88 * 89 * Most of the conditional compilation will (someday) vanish. 90 */ 91 92 #include <linux/module.h> 93 #include <linux/kernel.h> 94 #include <linux/sched.h> 95 #include <linux/slab.h> 96 #include <linux/init.h> 97 #include <linux/list.h> 98 #include <linux/kobject.h> 99 #include <linux/prefetch.h> 100 #include <linux/platform_device.h> 101 #include <linux/io.h> 102 103 #include "musb_core.h" 104 105 #define TA_WAIT_BCON(m) max_t(int, (m)->a_wait_bcon, OTG_TIME_A_WAIT_BCON) 106 107 108 #define DRIVER_AUTHOR "Mentor Graphics, Texas Instruments, Nokia" 109 #define DRIVER_DESC "Inventra Dual-Role USB Controller Driver" 110 111 #define MUSB_VERSION "6.0" 112 113 #define DRIVER_INFO DRIVER_DESC ", v" MUSB_VERSION 114 115 #define MUSB_DRIVER_NAME "musb-hdrc" 116 const char musb_driver_name[] = MUSB_DRIVER_NAME; 117 118 MODULE_DESCRIPTION(DRIVER_INFO); 119 MODULE_AUTHOR(DRIVER_AUTHOR); 120 MODULE_LICENSE("GPL"); 121 MODULE_ALIAS("platform:" MUSB_DRIVER_NAME); 122 123 124 /*-------------------------------------------------------------------------*/ 125 126 static inline struct musb *dev_to_musb(struct device *dev) 127 { 128 return dev_get_drvdata(dev); 129 } 130 131 /*-------------------------------------------------------------------------*/ 132 133 #ifndef CONFIG_BLACKFIN 134 static int musb_ulpi_read(struct otg_transceiver *otg, u32 offset) 135 { 136 void __iomem *addr = otg->io_priv; 137 int i = 0; 138 u8 r; 139 u8 power; 140 141 /* Make sure the transceiver is not in low power mode */ 142 power = musb_readb(addr, MUSB_POWER); 143 power &= ~MUSB_POWER_SUSPENDM; 144 musb_writeb(addr, MUSB_POWER, power); 145 146 /* REVISIT: musbhdrc_ulpi_an.pdf recommends setting the 147 * ULPICarKitControlDisableUTMI after clearing POWER_SUSPENDM. 148 */ 149 150 musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)offset); 151 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, 152 MUSB_ULPI_REG_REQ | MUSB_ULPI_RDN_WR); 153 154 while (!(musb_readb(addr, MUSB_ULPI_REG_CONTROL) 155 & MUSB_ULPI_REG_CMPLT)) { 156 i++; 157 if (i == 10000) 158 return -ETIMEDOUT; 159 160 } 161 r = musb_readb(addr, MUSB_ULPI_REG_CONTROL); 162 r &= ~MUSB_ULPI_REG_CMPLT; 163 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, r); 164 165 return musb_readb(addr, MUSB_ULPI_REG_DATA); 166 } 167 168 static int musb_ulpi_write(struct otg_transceiver *otg, 169 u32 offset, u32 data) 170 { 171 void __iomem *addr = otg->io_priv; 172 int i = 0; 173 u8 r = 0; 174 u8 power; 175 176 /* Make sure the transceiver is not in low power mode */ 177 power = musb_readb(addr, MUSB_POWER); 178 power &= ~MUSB_POWER_SUSPENDM; 179 musb_writeb(addr, MUSB_POWER, power); 180 181 musb_writeb(addr, MUSB_ULPI_REG_ADDR, (u8)offset); 182 musb_writeb(addr, MUSB_ULPI_REG_DATA, (u8)data); 183 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, MUSB_ULPI_REG_REQ); 184 185 while (!(musb_readb(addr, MUSB_ULPI_REG_CONTROL) 186 & MUSB_ULPI_REG_CMPLT)) { 187 i++; 188 if (i == 10000) 189 return -ETIMEDOUT; 190 } 191 192 r = musb_readb(addr, MUSB_ULPI_REG_CONTROL); 193 r &= ~MUSB_ULPI_REG_CMPLT; 194 musb_writeb(addr, MUSB_ULPI_REG_CONTROL, r); 195 196 return 0; 197 } 198 #else 199 #define musb_ulpi_read NULL 200 #define musb_ulpi_write NULL 201 #endif 202 203 static struct otg_io_access_ops musb_ulpi_access = { 204 .read = musb_ulpi_read, 205 .write = musb_ulpi_write, 206 }; 207 208 /*-------------------------------------------------------------------------*/ 209 210 #if !defined(CONFIG_USB_MUSB_TUSB6010) && !defined(CONFIG_USB_MUSB_BLACKFIN) 211 212 /* 213 * Load an endpoint's FIFO 214 */ 215 void musb_write_fifo(struct musb_hw_ep *hw_ep, u16 len, const u8 *src) 216 { 217 struct musb *musb = hw_ep->musb; 218 void __iomem *fifo = hw_ep->fifo; 219 220 prefetch((u8 *)src); 221 222 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n", 223 'T', hw_ep->epnum, fifo, len, src); 224 225 /* we can't assume unaligned reads work */ 226 if (likely((0x01 & (unsigned long) src) == 0)) { 227 u16 index = 0; 228 229 /* best case is 32bit-aligned source address */ 230 if ((0x02 & (unsigned long) src) == 0) { 231 if (len >= 4) { 232 writesl(fifo, src + index, len >> 2); 233 index += len & ~0x03; 234 } 235 if (len & 0x02) { 236 musb_writew(fifo, 0, *(u16 *)&src[index]); 237 index += 2; 238 } 239 } else { 240 if (len >= 2) { 241 writesw(fifo, src + index, len >> 1); 242 index += len & ~0x01; 243 } 244 } 245 if (len & 0x01) 246 musb_writeb(fifo, 0, src[index]); 247 } else { 248 /* byte aligned */ 249 writesb(fifo, src, len); 250 } 251 } 252 253 #if !defined(CONFIG_USB_MUSB_AM35X) 254 /* 255 * Unload an endpoint's FIFO 256 */ 257 void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst) 258 { 259 struct musb *musb = hw_ep->musb; 260 void __iomem *fifo = hw_ep->fifo; 261 262 dev_dbg(musb->controller, "%cX ep%d fifo %p count %d buf %p\n", 263 'R', hw_ep->epnum, fifo, len, dst); 264 265 /* we can't assume unaligned writes work */ 266 if (likely((0x01 & (unsigned long) dst) == 0)) { 267 u16 index = 0; 268 269 /* best case is 32bit-aligned destination address */ 270 if ((0x02 & (unsigned long) dst) == 0) { 271 if (len >= 4) { 272 readsl(fifo, dst, len >> 2); 273 index = len & ~0x03; 274 } 275 if (len & 0x02) { 276 *(u16 *)&dst[index] = musb_readw(fifo, 0); 277 index += 2; 278 } 279 } else { 280 if (len >= 2) { 281 readsw(fifo, dst, len >> 1); 282 index = len & ~0x01; 283 } 284 } 285 if (len & 0x01) 286 dst[index] = musb_readb(fifo, 0); 287 } else { 288 /* byte aligned */ 289 readsb(fifo, dst, len); 290 } 291 } 292 #endif 293 294 #endif /* normal PIO */ 295 296 297 /*-------------------------------------------------------------------------*/ 298 299 /* for high speed test mode; see USB 2.0 spec 7.1.20 */ 300 static const u8 musb_test_packet[53] = { 301 /* implicit SYNC then DATA0 to start */ 302 303 /* JKJKJKJK x9 */ 304 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 305 /* JJKKJJKK x8 */ 306 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 0xaa, 307 /* JJJJKKKK x8 */ 308 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 0xee, 309 /* JJJJJJJKKKKKKK x8 */ 310 0xfe, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 311 /* JJJJJJJK x8 */ 312 0x7f, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd, 313 /* JKKKKKKK x10, JK */ 314 0xfc, 0x7e, 0xbf, 0xdf, 0xef, 0xf7, 0xfb, 0xfd, 0x7e 315 316 /* implicit CRC16 then EOP to end */ 317 }; 318 319 void musb_load_testpacket(struct musb *musb) 320 { 321 void __iomem *regs = musb->endpoints[0].regs; 322 323 musb_ep_select(musb->mregs, 0); 324 musb_write_fifo(musb->control_ep, 325 sizeof(musb_test_packet), musb_test_packet); 326 musb_writew(regs, MUSB_CSR0, MUSB_CSR0_TXPKTRDY); 327 } 328 329 /*-------------------------------------------------------------------------*/ 330 331 /* 332 * Handles OTG hnp timeouts, such as b_ase0_brst 333 */ 334 void musb_otg_timer_func(unsigned long data) 335 { 336 struct musb *musb = (struct musb *)data; 337 unsigned long flags; 338 339 spin_lock_irqsave(&musb->lock, flags); 340 switch (musb->xceiv->state) { 341 case OTG_STATE_B_WAIT_ACON: 342 dev_dbg(musb->controller, "HNP: b_wait_acon timeout; back to b_peripheral\n"); 343 musb_g_disconnect(musb); 344 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 345 musb->is_active = 0; 346 break; 347 case OTG_STATE_A_SUSPEND: 348 case OTG_STATE_A_WAIT_BCON: 349 dev_dbg(musb->controller, "HNP: %s timeout\n", 350 otg_state_string(musb->xceiv->state)); 351 musb_platform_set_vbus(musb, 0); 352 musb->xceiv->state = OTG_STATE_A_WAIT_VFALL; 353 break; 354 default: 355 dev_dbg(musb->controller, "HNP: Unhandled mode %s\n", 356 otg_state_string(musb->xceiv->state)); 357 } 358 musb->ignore_disconnect = 0; 359 spin_unlock_irqrestore(&musb->lock, flags); 360 } 361 362 /* 363 * Stops the HNP transition. Caller must take care of locking. 364 */ 365 void musb_hnp_stop(struct musb *musb) 366 { 367 struct usb_hcd *hcd = musb_to_hcd(musb); 368 void __iomem *mbase = musb->mregs; 369 u8 reg; 370 371 dev_dbg(musb->controller, "HNP: stop from %s\n", otg_state_string(musb->xceiv->state)); 372 373 switch (musb->xceiv->state) { 374 case OTG_STATE_A_PERIPHERAL: 375 musb_g_disconnect(musb); 376 dev_dbg(musb->controller, "HNP: back to %s\n", 377 otg_state_string(musb->xceiv->state)); 378 break; 379 case OTG_STATE_B_HOST: 380 dev_dbg(musb->controller, "HNP: Disabling HR\n"); 381 hcd->self.is_b_host = 0; 382 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 383 MUSB_DEV_MODE(musb); 384 reg = musb_readb(mbase, MUSB_POWER); 385 reg |= MUSB_POWER_SUSPENDM; 386 musb_writeb(mbase, MUSB_POWER, reg); 387 /* REVISIT: Start SESSION_REQUEST here? */ 388 break; 389 default: 390 dev_dbg(musb->controller, "HNP: Stopping in unknown state %s\n", 391 otg_state_string(musb->xceiv->state)); 392 } 393 394 /* 395 * When returning to A state after HNP, avoid hub_port_rebounce(), 396 * which cause occasional OPT A "Did not receive reset after connect" 397 * errors. 398 */ 399 musb->port1_status &= ~(USB_PORT_STAT_C_CONNECTION << 16); 400 } 401 402 /* 403 * Interrupt Service Routine to record USB "global" interrupts. 404 * Since these do not happen often and signify things of 405 * paramount importance, it seems OK to check them individually; 406 * the order of the tests is specified in the manual 407 * 408 * @param musb instance pointer 409 * @param int_usb register contents 410 * @param devctl 411 * @param power 412 */ 413 414 static irqreturn_t musb_stage0_irq(struct musb *musb, u8 int_usb, 415 u8 devctl, u8 power) 416 { 417 irqreturn_t handled = IRQ_NONE; 418 419 dev_dbg(musb->controller, "<== Power=%02x, DevCtl=%02x, int_usb=0x%x\n", power, devctl, 420 int_usb); 421 422 /* in host mode, the peripheral may issue remote wakeup. 423 * in peripheral mode, the host may resume the link. 424 * spurious RESUME irqs happen too, paired with SUSPEND. 425 */ 426 if (int_usb & MUSB_INTR_RESUME) { 427 handled = IRQ_HANDLED; 428 dev_dbg(musb->controller, "RESUME (%s)\n", otg_state_string(musb->xceiv->state)); 429 430 if (devctl & MUSB_DEVCTL_HM) { 431 void __iomem *mbase = musb->mregs; 432 433 switch (musb->xceiv->state) { 434 case OTG_STATE_A_SUSPEND: 435 /* remote wakeup? later, GetPortStatus 436 * will stop RESUME signaling 437 */ 438 439 if (power & MUSB_POWER_SUSPENDM) { 440 /* spurious */ 441 musb->int_usb &= ~MUSB_INTR_SUSPEND; 442 dev_dbg(musb->controller, "Spurious SUSPENDM\n"); 443 break; 444 } 445 446 power &= ~MUSB_POWER_SUSPENDM; 447 musb_writeb(mbase, MUSB_POWER, 448 power | MUSB_POWER_RESUME); 449 450 musb->port1_status |= 451 (USB_PORT_STAT_C_SUSPEND << 16) 452 | MUSB_PORT_STAT_RESUME; 453 musb->rh_timer = jiffies 454 + msecs_to_jiffies(20); 455 456 musb->xceiv->state = OTG_STATE_A_HOST; 457 musb->is_active = 1; 458 usb_hcd_resume_root_hub(musb_to_hcd(musb)); 459 break; 460 case OTG_STATE_B_WAIT_ACON: 461 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 462 musb->is_active = 1; 463 MUSB_DEV_MODE(musb); 464 break; 465 default: 466 WARNING("bogus %s RESUME (%s)\n", 467 "host", 468 otg_state_string(musb->xceiv->state)); 469 } 470 } else { 471 switch (musb->xceiv->state) { 472 case OTG_STATE_A_SUSPEND: 473 /* possibly DISCONNECT is upcoming */ 474 musb->xceiv->state = OTG_STATE_A_HOST; 475 usb_hcd_resume_root_hub(musb_to_hcd(musb)); 476 break; 477 case OTG_STATE_B_WAIT_ACON: 478 case OTG_STATE_B_PERIPHERAL: 479 /* disconnect while suspended? we may 480 * not get a disconnect irq... 481 */ 482 if ((devctl & MUSB_DEVCTL_VBUS) 483 != (3 << MUSB_DEVCTL_VBUS_SHIFT) 484 ) { 485 musb->int_usb |= MUSB_INTR_DISCONNECT; 486 musb->int_usb &= ~MUSB_INTR_SUSPEND; 487 break; 488 } 489 musb_g_resume(musb); 490 break; 491 case OTG_STATE_B_IDLE: 492 musb->int_usb &= ~MUSB_INTR_SUSPEND; 493 break; 494 default: 495 WARNING("bogus %s RESUME (%s)\n", 496 "peripheral", 497 otg_state_string(musb->xceiv->state)); 498 } 499 } 500 } 501 502 /* see manual for the order of the tests */ 503 if (int_usb & MUSB_INTR_SESSREQ) { 504 void __iomem *mbase = musb->mregs; 505 506 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS 507 && (devctl & MUSB_DEVCTL_BDEVICE)) { 508 dev_dbg(musb->controller, "SessReq while on B state\n"); 509 return IRQ_HANDLED; 510 } 511 512 dev_dbg(musb->controller, "SESSION_REQUEST (%s)\n", 513 otg_state_string(musb->xceiv->state)); 514 515 /* IRQ arrives from ID pin sense or (later, if VBUS power 516 * is removed) SRP. responses are time critical: 517 * - turn on VBUS (with silicon-specific mechanism) 518 * - go through A_WAIT_VRISE 519 * - ... to A_WAIT_BCON. 520 * a_wait_vrise_tmout triggers VBUS_ERROR transitions 521 */ 522 musb_writeb(mbase, MUSB_DEVCTL, MUSB_DEVCTL_SESSION); 523 musb->ep0_stage = MUSB_EP0_START; 524 musb->xceiv->state = OTG_STATE_A_IDLE; 525 MUSB_HST_MODE(musb); 526 musb_platform_set_vbus(musb, 1); 527 528 handled = IRQ_HANDLED; 529 } 530 531 if (int_usb & MUSB_INTR_VBUSERROR) { 532 int ignore = 0; 533 534 /* During connection as an A-Device, we may see a short 535 * current spikes causing voltage drop, because of cable 536 * and peripheral capacitance combined with vbus draw. 537 * (So: less common with truly self-powered devices, where 538 * vbus doesn't act like a power supply.) 539 * 540 * Such spikes are short; usually less than ~500 usec, max 541 * of ~2 msec. That is, they're not sustained overcurrent 542 * errors, though they're reported using VBUSERROR irqs. 543 * 544 * Workarounds: (a) hardware: use self powered devices. 545 * (b) software: ignore non-repeated VBUS errors. 546 * 547 * REVISIT: do delays from lots of DEBUG_KERNEL checks 548 * make trouble here, keeping VBUS < 4.4V ? 549 */ 550 switch (musb->xceiv->state) { 551 case OTG_STATE_A_HOST: 552 /* recovery is dicey once we've gotten past the 553 * initial stages of enumeration, but if VBUS 554 * stayed ok at the other end of the link, and 555 * another reset is due (at least for high speed, 556 * to redo the chirp etc), it might work OK... 557 */ 558 case OTG_STATE_A_WAIT_BCON: 559 case OTG_STATE_A_WAIT_VRISE: 560 if (musb->vbuserr_retry) { 561 void __iomem *mbase = musb->mregs; 562 563 musb->vbuserr_retry--; 564 ignore = 1; 565 devctl |= MUSB_DEVCTL_SESSION; 566 musb_writeb(mbase, MUSB_DEVCTL, devctl); 567 } else { 568 musb->port1_status |= 569 USB_PORT_STAT_OVERCURRENT 570 | (USB_PORT_STAT_C_OVERCURRENT << 16); 571 } 572 break; 573 default: 574 break; 575 } 576 577 dev_dbg(musb->controller, "VBUS_ERROR in %s (%02x, %s), retry #%d, port1 %08x\n", 578 otg_state_string(musb->xceiv->state), 579 devctl, 580 ({ char *s; 581 switch (devctl & MUSB_DEVCTL_VBUS) { 582 case 0 << MUSB_DEVCTL_VBUS_SHIFT: 583 s = "<SessEnd"; break; 584 case 1 << MUSB_DEVCTL_VBUS_SHIFT: 585 s = "<AValid"; break; 586 case 2 << MUSB_DEVCTL_VBUS_SHIFT: 587 s = "<VBusValid"; break; 588 /* case 3 << MUSB_DEVCTL_VBUS_SHIFT: */ 589 default: 590 s = "VALID"; break; 591 }; s; }), 592 VBUSERR_RETRY_COUNT - musb->vbuserr_retry, 593 musb->port1_status); 594 595 /* go through A_WAIT_VFALL then start a new session */ 596 if (!ignore) 597 musb_platform_set_vbus(musb, 0); 598 handled = IRQ_HANDLED; 599 } 600 601 if (int_usb & MUSB_INTR_SUSPEND) { 602 dev_dbg(musb->controller, "SUSPEND (%s) devctl %02x power %02x\n", 603 otg_state_string(musb->xceiv->state), devctl, power); 604 handled = IRQ_HANDLED; 605 606 switch (musb->xceiv->state) { 607 case OTG_STATE_A_PERIPHERAL: 608 /* We also come here if the cable is removed, since 609 * this silicon doesn't report ID-no-longer-grounded. 610 * 611 * We depend on T(a_wait_bcon) to shut us down, and 612 * hope users don't do anything dicey during this 613 * undesired detour through A_WAIT_BCON. 614 */ 615 musb_hnp_stop(musb); 616 usb_hcd_resume_root_hub(musb_to_hcd(musb)); 617 musb_root_disconnect(musb); 618 musb_platform_try_idle(musb, jiffies 619 + msecs_to_jiffies(musb->a_wait_bcon 620 ? : OTG_TIME_A_WAIT_BCON)); 621 622 break; 623 case OTG_STATE_B_IDLE: 624 if (!musb->is_active) 625 break; 626 case OTG_STATE_B_PERIPHERAL: 627 musb_g_suspend(musb); 628 musb->is_active = is_otg_enabled(musb) 629 && musb->xceiv->gadget->b_hnp_enable; 630 if (musb->is_active) { 631 musb->xceiv->state = OTG_STATE_B_WAIT_ACON; 632 dev_dbg(musb->controller, "HNP: Setting timer for b_ase0_brst\n"); 633 mod_timer(&musb->otg_timer, jiffies 634 + msecs_to_jiffies( 635 OTG_TIME_B_ASE0_BRST)); 636 } 637 break; 638 case OTG_STATE_A_WAIT_BCON: 639 if (musb->a_wait_bcon != 0) 640 musb_platform_try_idle(musb, jiffies 641 + msecs_to_jiffies(musb->a_wait_bcon)); 642 break; 643 case OTG_STATE_A_HOST: 644 musb->xceiv->state = OTG_STATE_A_SUSPEND; 645 musb->is_active = is_otg_enabled(musb) 646 && musb->xceiv->host->b_hnp_enable; 647 break; 648 case OTG_STATE_B_HOST: 649 /* Transition to B_PERIPHERAL, see 6.8.2.6 p 44 */ 650 dev_dbg(musb->controller, "REVISIT: SUSPEND as B_HOST\n"); 651 break; 652 default: 653 /* "should not happen" */ 654 musb->is_active = 0; 655 break; 656 } 657 } 658 659 if (int_usb & MUSB_INTR_CONNECT) { 660 struct usb_hcd *hcd = musb_to_hcd(musb); 661 662 handled = IRQ_HANDLED; 663 musb->is_active = 1; 664 set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags); 665 666 musb->ep0_stage = MUSB_EP0_START; 667 668 /* flush endpoints when transitioning from Device Mode */ 669 if (is_peripheral_active(musb)) { 670 /* REVISIT HNP; just force disconnect */ 671 } 672 musb_writew(musb->mregs, MUSB_INTRTXE, musb->epmask); 673 musb_writew(musb->mregs, MUSB_INTRRXE, musb->epmask & 0xfffe); 674 musb_writeb(musb->mregs, MUSB_INTRUSBE, 0xf7); 675 musb->port1_status &= ~(USB_PORT_STAT_LOW_SPEED 676 |USB_PORT_STAT_HIGH_SPEED 677 |USB_PORT_STAT_ENABLE 678 ); 679 musb->port1_status |= USB_PORT_STAT_CONNECTION 680 |(USB_PORT_STAT_C_CONNECTION << 16); 681 682 /* high vs full speed is just a guess until after reset */ 683 if (devctl & MUSB_DEVCTL_LSDEV) 684 musb->port1_status |= USB_PORT_STAT_LOW_SPEED; 685 686 /* indicate new connection to OTG machine */ 687 switch (musb->xceiv->state) { 688 case OTG_STATE_B_PERIPHERAL: 689 if (int_usb & MUSB_INTR_SUSPEND) { 690 dev_dbg(musb->controller, "HNP: SUSPEND+CONNECT, now b_host\n"); 691 int_usb &= ~MUSB_INTR_SUSPEND; 692 goto b_host; 693 } else 694 dev_dbg(musb->controller, "CONNECT as b_peripheral???\n"); 695 break; 696 case OTG_STATE_B_WAIT_ACON: 697 dev_dbg(musb->controller, "HNP: CONNECT, now b_host\n"); 698 b_host: 699 musb->xceiv->state = OTG_STATE_B_HOST; 700 hcd->self.is_b_host = 1; 701 musb->ignore_disconnect = 0; 702 del_timer(&musb->otg_timer); 703 break; 704 default: 705 if ((devctl & MUSB_DEVCTL_VBUS) 706 == (3 << MUSB_DEVCTL_VBUS_SHIFT)) { 707 musb->xceiv->state = OTG_STATE_A_HOST; 708 hcd->self.is_b_host = 0; 709 } 710 break; 711 } 712 713 /* poke the root hub */ 714 MUSB_HST_MODE(musb); 715 if (hcd->status_urb) 716 usb_hcd_poll_rh_status(hcd); 717 else 718 usb_hcd_resume_root_hub(hcd); 719 720 dev_dbg(musb->controller, "CONNECT (%s) devctl %02x\n", 721 otg_state_string(musb->xceiv->state), devctl); 722 } 723 724 if ((int_usb & MUSB_INTR_DISCONNECT) && !musb->ignore_disconnect) { 725 dev_dbg(musb->controller, "DISCONNECT (%s) as %s, devctl %02x\n", 726 otg_state_string(musb->xceiv->state), 727 MUSB_MODE(musb), devctl); 728 handled = IRQ_HANDLED; 729 730 switch (musb->xceiv->state) { 731 case OTG_STATE_A_HOST: 732 case OTG_STATE_A_SUSPEND: 733 usb_hcd_resume_root_hub(musb_to_hcd(musb)); 734 musb_root_disconnect(musb); 735 if (musb->a_wait_bcon != 0 && is_otg_enabled(musb)) 736 musb_platform_try_idle(musb, jiffies 737 + msecs_to_jiffies(musb->a_wait_bcon)); 738 break; 739 case OTG_STATE_B_HOST: 740 /* REVISIT this behaves for "real disconnect" 741 * cases; make sure the other transitions from 742 * from B_HOST act right too. The B_HOST code 743 * in hnp_stop() is currently not used... 744 */ 745 musb_root_disconnect(musb); 746 musb_to_hcd(musb)->self.is_b_host = 0; 747 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 748 MUSB_DEV_MODE(musb); 749 musb_g_disconnect(musb); 750 break; 751 case OTG_STATE_A_PERIPHERAL: 752 musb_hnp_stop(musb); 753 musb_root_disconnect(musb); 754 /* FALLTHROUGH */ 755 case OTG_STATE_B_WAIT_ACON: 756 /* FALLTHROUGH */ 757 case OTG_STATE_B_PERIPHERAL: 758 case OTG_STATE_B_IDLE: 759 musb_g_disconnect(musb); 760 break; 761 default: 762 WARNING("unhandled DISCONNECT transition (%s)\n", 763 otg_state_string(musb->xceiv->state)); 764 break; 765 } 766 } 767 768 /* mentor saves a bit: bus reset and babble share the same irq. 769 * only host sees babble; only peripheral sees bus reset. 770 */ 771 if (int_usb & MUSB_INTR_RESET) { 772 handled = IRQ_HANDLED; 773 if (is_host_capable() && (devctl & MUSB_DEVCTL_HM) != 0) { 774 /* 775 * Looks like non-HS BABBLE can be ignored, but 776 * HS BABBLE is an error condition. For HS the solution 777 * is to avoid babble in the first place and fix what 778 * caused BABBLE. When HS BABBLE happens we can only 779 * stop the session. 780 */ 781 if (devctl & (MUSB_DEVCTL_FSDEV | MUSB_DEVCTL_LSDEV)) 782 dev_dbg(musb->controller, "BABBLE devctl: %02x\n", devctl); 783 else { 784 ERR("Stopping host session -- babble\n"); 785 musb_writeb(musb->mregs, MUSB_DEVCTL, 0); 786 } 787 } else if (is_peripheral_capable()) { 788 dev_dbg(musb->controller, "BUS RESET as %s\n", 789 otg_state_string(musb->xceiv->state)); 790 switch (musb->xceiv->state) { 791 case OTG_STATE_A_SUSPEND: 792 /* We need to ignore disconnect on suspend 793 * otherwise tusb 2.0 won't reconnect after a 794 * power cycle, which breaks otg compliance. 795 */ 796 musb->ignore_disconnect = 1; 797 musb_g_reset(musb); 798 /* FALLTHROUGH */ 799 case OTG_STATE_A_WAIT_BCON: /* OPT TD.4.7-900ms */ 800 /* never use invalid T(a_wait_bcon) */ 801 dev_dbg(musb->controller, "HNP: in %s, %d msec timeout\n", 802 otg_state_string(musb->xceiv->state), 803 TA_WAIT_BCON(musb)); 804 mod_timer(&musb->otg_timer, jiffies 805 + msecs_to_jiffies(TA_WAIT_BCON(musb))); 806 break; 807 case OTG_STATE_A_PERIPHERAL: 808 musb->ignore_disconnect = 0; 809 del_timer(&musb->otg_timer); 810 musb_g_reset(musb); 811 break; 812 case OTG_STATE_B_WAIT_ACON: 813 dev_dbg(musb->controller, "HNP: RESET (%s), to b_peripheral\n", 814 otg_state_string(musb->xceiv->state)); 815 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 816 musb_g_reset(musb); 817 break; 818 case OTG_STATE_B_IDLE: 819 musb->xceiv->state = OTG_STATE_B_PERIPHERAL; 820 /* FALLTHROUGH */ 821 case OTG_STATE_B_PERIPHERAL: 822 musb_g_reset(musb); 823 break; 824 default: 825 dev_dbg(musb->controller, "Unhandled BUS RESET as %s\n", 826 otg_state_string(musb->xceiv->state)); 827 } 828 } 829 } 830 831 #if 0 832 /* REVISIT ... this would be for multiplexing periodic endpoints, or 833 * supporting transfer phasing to prevent exceeding ISO bandwidth 834 * limits of a given frame or microframe. 835 * 836 * It's not needed for peripheral side, which dedicates endpoints; 837 * though it _might_ use SOF irqs for other purposes. 838 * 839 * And it's not currently needed for host side, which also dedicates 840 * endpoints, relies on TX/RX interval registers, and isn't claimed 841 * to support ISO transfers yet. 842 */ 843 if (int_usb & MUSB_INTR_SOF) { 844 void __iomem *mbase = musb->mregs; 845 struct musb_hw_ep *ep; 846 u8 epnum; 847 u16 frame; 848 849 dev_dbg(musb->controller, "START_OF_FRAME\n"); 850 handled = IRQ_HANDLED; 851 852 /* start any periodic Tx transfers waiting for current frame */ 853 frame = musb_readw(mbase, MUSB_FRAME); 854 ep = musb->endpoints; 855 for (epnum = 1; (epnum < musb->nr_endpoints) 856 && (musb->epmask >= (1 << epnum)); 857 epnum++, ep++) { 858 /* 859 * FIXME handle framecounter wraps (12 bits) 860 * eliminate duplicated StartUrb logic 861 */ 862 if (ep->dwWaitFrame >= frame) { 863 ep->dwWaitFrame = 0; 864 pr_debug("SOF --> periodic TX%s on %d\n", 865 ep->tx_channel ? " DMA" : "", 866 epnum); 867 if (!ep->tx_channel) 868 musb_h_tx_start(musb, epnum); 869 else 870 cppi_hostdma_start(musb, epnum); 871 } 872 } /* end of for loop */ 873 } 874 #endif 875 876 schedule_work(&musb->irq_work); 877 878 return handled; 879 } 880 881 /*-------------------------------------------------------------------------*/ 882 883 /* 884 * Program the HDRC to start (enable interrupts, dma, etc.). 885 */ 886 void musb_start(struct musb *musb) 887 { 888 void __iomem *regs = musb->mregs; 889 u8 devctl = musb_readb(regs, MUSB_DEVCTL); 890 891 dev_dbg(musb->controller, "<== devctl %02x\n", devctl); 892 893 /* Set INT enable registers, enable interrupts */ 894 musb_writew(regs, MUSB_INTRTXE, musb->epmask); 895 musb_writew(regs, MUSB_INTRRXE, musb->epmask & 0xfffe); 896 musb_writeb(regs, MUSB_INTRUSBE, 0xf7); 897 898 musb_writeb(regs, MUSB_TESTMODE, 0); 899 900 /* put into basic highspeed mode and start session */ 901 musb_writeb(regs, MUSB_POWER, MUSB_POWER_ISOUPDATE 902 | MUSB_POWER_HSENAB 903 /* ENSUSPEND wedges tusb */ 904 /* | MUSB_POWER_ENSUSPEND */ 905 ); 906 907 musb->is_active = 0; 908 devctl = musb_readb(regs, MUSB_DEVCTL); 909 devctl &= ~MUSB_DEVCTL_SESSION; 910 911 if (is_otg_enabled(musb)) { 912 /* session started after: 913 * (a) ID-grounded irq, host mode; 914 * (b) vbus present/connect IRQ, peripheral mode; 915 * (c) peripheral initiates, using SRP 916 */ 917 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) 918 musb->is_active = 1; 919 else 920 devctl |= MUSB_DEVCTL_SESSION; 921 922 } else if (is_host_enabled(musb)) { 923 /* assume ID pin is hard-wired to ground */ 924 devctl |= MUSB_DEVCTL_SESSION; 925 926 } else /* peripheral is enabled */ { 927 if ((devctl & MUSB_DEVCTL_VBUS) == MUSB_DEVCTL_VBUS) 928 musb->is_active = 1; 929 } 930 musb_platform_enable(musb); 931 musb_writeb(regs, MUSB_DEVCTL, devctl); 932 } 933 934 935 static void musb_generic_disable(struct musb *musb) 936 { 937 void __iomem *mbase = musb->mregs; 938 u16 temp; 939 940 /* disable interrupts */ 941 musb_writeb(mbase, MUSB_INTRUSBE, 0); 942 musb_writew(mbase, MUSB_INTRTXE, 0); 943 musb_writew(mbase, MUSB_INTRRXE, 0); 944 945 /* off */ 946 musb_writeb(mbase, MUSB_DEVCTL, 0); 947 948 /* flush pending interrupts */ 949 temp = musb_readb(mbase, MUSB_INTRUSB); 950 temp = musb_readw(mbase, MUSB_INTRTX); 951 temp = musb_readw(mbase, MUSB_INTRRX); 952 953 } 954 955 /* 956 * Make the HDRC stop (disable interrupts, etc.); 957 * reversible by musb_start 958 * called on gadget driver unregister 959 * with controller locked, irqs blocked 960 * acts as a NOP unless some role activated the hardware 961 */ 962 void musb_stop(struct musb *musb) 963 { 964 /* stop IRQs, timers, ... */ 965 musb_platform_disable(musb); 966 musb_generic_disable(musb); 967 dev_dbg(musb->controller, "HDRC disabled\n"); 968 969 /* FIXME 970 * - mark host and/or peripheral drivers unusable/inactive 971 * - disable DMA (and enable it in HdrcStart) 972 * - make sure we can musb_start() after musb_stop(); with 973 * OTG mode, gadget driver module rmmod/modprobe cycles that 974 * - ... 975 */ 976 musb_platform_try_idle(musb, 0); 977 } 978 979 static void musb_shutdown(struct platform_device *pdev) 980 { 981 struct musb *musb = dev_to_musb(&pdev->dev); 982 unsigned long flags; 983 984 pm_runtime_get_sync(musb->controller); 985 spin_lock_irqsave(&musb->lock, flags); 986 musb_platform_disable(musb); 987 musb_generic_disable(musb); 988 spin_unlock_irqrestore(&musb->lock, flags); 989 990 if (!is_otg_enabled(musb) && is_host_enabled(musb)) 991 usb_remove_hcd(musb_to_hcd(musb)); 992 musb_writeb(musb->mregs, MUSB_DEVCTL, 0); 993 musb_platform_exit(musb); 994 995 pm_runtime_put(musb->controller); 996 /* FIXME power down */ 997 } 998 999 1000 /*-------------------------------------------------------------------------*/ 1001 1002 /* 1003 * The silicon either has hard-wired endpoint configurations, or else 1004 * "dynamic fifo" sizing. The driver has support for both, though at this 1005 * writing only the dynamic sizing is very well tested. Since we switched 1006 * away from compile-time hardware parameters, we can no longer rely on 1007 * dead code elimination to leave only the relevant one in the object file. 1008 * 1009 * We don't currently use dynamic fifo setup capability to do anything 1010 * more than selecting one of a bunch of predefined configurations. 1011 */ 1012 #if defined(CONFIG_USB_MUSB_TUSB6010) \ 1013 || defined(CONFIG_USB_MUSB_TUSB6010_MODULE) \ 1014 || defined(CONFIG_USB_MUSB_OMAP2PLUS) \ 1015 || defined(CONFIG_USB_MUSB_OMAP2PLUS_MODULE) \ 1016 || defined(CONFIG_USB_MUSB_AM35X) \ 1017 || defined(CONFIG_USB_MUSB_AM35X_MODULE) 1018 static ushort __initdata fifo_mode = 4; 1019 #elif defined(CONFIG_USB_MUSB_UX500) \ 1020 || defined(CONFIG_USB_MUSB_UX500_MODULE) 1021 static ushort __initdata fifo_mode = 5; 1022 #else 1023 static ushort __initdata fifo_mode = 2; 1024 #endif 1025 1026 /* "modprobe ... fifo_mode=1" etc */ 1027 module_param(fifo_mode, ushort, 0); 1028 MODULE_PARM_DESC(fifo_mode, "initial endpoint configuration"); 1029 1030 /* 1031 * tables defining fifo_mode values. define more if you like. 1032 * for host side, make sure both halves of ep1 are set up. 1033 */ 1034 1035 /* mode 0 - fits in 2KB */ 1036 static struct musb_fifo_cfg __initdata mode_0_cfg[] = { 1037 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, 1038 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, 1039 { .hw_ep_num = 2, .style = FIFO_RXTX, .maxpacket = 512, }, 1040 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, 1041 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, 1042 }; 1043 1044 /* mode 1 - fits in 4KB */ 1045 static struct musb_fifo_cfg __initdata mode_1_cfg[] = { 1046 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, .mode = BUF_DOUBLE, }, 1047 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, .mode = BUF_DOUBLE, }, 1048 { .hw_ep_num = 2, .style = FIFO_RXTX, .maxpacket = 512, .mode = BUF_DOUBLE, }, 1049 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, 1050 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, 1051 }; 1052 1053 /* mode 2 - fits in 4KB */ 1054 static struct musb_fifo_cfg __initdata mode_2_cfg[] = { 1055 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, 1056 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, 1057 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, 1058 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, 1059 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, 1060 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, 1061 }; 1062 1063 /* mode 3 - fits in 4KB */ 1064 static struct musb_fifo_cfg __initdata mode_3_cfg[] = { 1065 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, .mode = BUF_DOUBLE, }, 1066 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, .mode = BUF_DOUBLE, }, 1067 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, 1068 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, 1069 { .hw_ep_num = 3, .style = FIFO_RXTX, .maxpacket = 256, }, 1070 { .hw_ep_num = 4, .style = FIFO_RXTX, .maxpacket = 256, }, 1071 }; 1072 1073 /* mode 4 - fits in 16KB */ 1074 static struct musb_fifo_cfg __initdata mode_4_cfg[] = { 1075 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, 1076 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, 1077 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, 1078 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, 1079 { .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, }, 1080 { .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, }, 1081 { .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, }, 1082 { .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, }, 1083 { .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, }, 1084 { .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, }, 1085 { .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 512, }, 1086 { .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 512, }, 1087 { .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 512, }, 1088 { .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 512, }, 1089 { .hw_ep_num = 8, .style = FIFO_TX, .maxpacket = 512, }, 1090 { .hw_ep_num = 8, .style = FIFO_RX, .maxpacket = 512, }, 1091 { .hw_ep_num = 9, .style = FIFO_TX, .maxpacket = 512, }, 1092 { .hw_ep_num = 9, .style = FIFO_RX, .maxpacket = 512, }, 1093 { .hw_ep_num = 10, .style = FIFO_TX, .maxpacket = 256, }, 1094 { .hw_ep_num = 10, .style = FIFO_RX, .maxpacket = 64, }, 1095 { .hw_ep_num = 11, .style = FIFO_TX, .maxpacket = 256, }, 1096 { .hw_ep_num = 11, .style = FIFO_RX, .maxpacket = 64, }, 1097 { .hw_ep_num = 12, .style = FIFO_TX, .maxpacket = 256, }, 1098 { .hw_ep_num = 12, .style = FIFO_RX, .maxpacket = 64, }, 1099 { .hw_ep_num = 13, .style = FIFO_RXTX, .maxpacket = 4096, }, 1100 { .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, }, 1101 { .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, }, 1102 }; 1103 1104 /* mode 5 - fits in 8KB */ 1105 static struct musb_fifo_cfg __initdata mode_5_cfg[] = { 1106 { .hw_ep_num = 1, .style = FIFO_TX, .maxpacket = 512, }, 1107 { .hw_ep_num = 1, .style = FIFO_RX, .maxpacket = 512, }, 1108 { .hw_ep_num = 2, .style = FIFO_TX, .maxpacket = 512, }, 1109 { .hw_ep_num = 2, .style = FIFO_RX, .maxpacket = 512, }, 1110 { .hw_ep_num = 3, .style = FIFO_TX, .maxpacket = 512, }, 1111 { .hw_ep_num = 3, .style = FIFO_RX, .maxpacket = 512, }, 1112 { .hw_ep_num = 4, .style = FIFO_TX, .maxpacket = 512, }, 1113 { .hw_ep_num = 4, .style = FIFO_RX, .maxpacket = 512, }, 1114 { .hw_ep_num = 5, .style = FIFO_TX, .maxpacket = 512, }, 1115 { .hw_ep_num = 5, .style = FIFO_RX, .maxpacket = 512, }, 1116 { .hw_ep_num = 6, .style = FIFO_TX, .maxpacket = 32, }, 1117 { .hw_ep_num = 6, .style = FIFO_RX, .maxpacket = 32, }, 1118 { .hw_ep_num = 7, .style = FIFO_TX, .maxpacket = 32, }, 1119 { .hw_ep_num = 7, .style = FIFO_RX, .maxpacket = 32, }, 1120 { .hw_ep_num = 8, .style = FIFO_TX, .maxpacket = 32, }, 1121 { .hw_ep_num = 8, .style = FIFO_RX, .maxpacket = 32, }, 1122 { .hw_ep_num = 9, .style = FIFO_TX, .maxpacket = 32, }, 1123 { .hw_ep_num = 9, .style = FIFO_RX, .maxpacket = 32, }, 1124 { .hw_ep_num = 10, .style = FIFO_TX, .maxpacket = 32, }, 1125 { .hw_ep_num = 10, .style = FIFO_RX, .maxpacket = 32, }, 1126 { .hw_ep_num = 11, .style = FIFO_TX, .maxpacket = 32, }, 1127 { .hw_ep_num = 11, .style = FIFO_RX, .maxpacket = 32, }, 1128 { .hw_ep_num = 12, .style = FIFO_TX, .maxpacket = 32, }, 1129 { .hw_ep_num = 12, .style = FIFO_RX, .maxpacket = 32, }, 1130 { .hw_ep_num = 13, .style = FIFO_RXTX, .maxpacket = 512, }, 1131 { .hw_ep_num = 14, .style = FIFO_RXTX, .maxpacket = 1024, }, 1132 { .hw_ep_num = 15, .style = FIFO_RXTX, .maxpacket = 1024, }, 1133 }; 1134 1135 /* 1136 * configure a fifo; for non-shared endpoints, this may be called 1137 * once for a tx fifo and once for an rx fifo. 1138 * 1139 * returns negative errno or offset for next fifo. 1140 */ 1141 static int __init 1142 fifo_setup(struct musb *musb, struct musb_hw_ep *hw_ep, 1143 const struct musb_fifo_cfg *cfg, u16 offset) 1144 { 1145 void __iomem *mbase = musb->mregs; 1146 int size = 0; 1147 u16 maxpacket = cfg->maxpacket; 1148 u16 c_off = offset >> 3; 1149 u8 c_size; 1150 1151 /* expect hw_ep has already been zero-initialized */ 1152 1153 size = ffs(max(maxpacket, (u16) 8)) - 1; 1154 maxpacket = 1 << size; 1155 1156 c_size = size - 3; 1157 if (cfg->mode == BUF_DOUBLE) { 1158 if ((offset + (maxpacket << 1)) > 1159 (1 << (musb->config->ram_bits + 2))) 1160 return -EMSGSIZE; 1161 c_size |= MUSB_FIFOSZ_DPB; 1162 } else { 1163 if ((offset + maxpacket) > (1 << (musb->config->ram_bits + 2))) 1164 return -EMSGSIZE; 1165 } 1166 1167 /* configure the FIFO */ 1168 musb_writeb(mbase, MUSB_INDEX, hw_ep->epnum); 1169 1170 /* EP0 reserved endpoint for control, bidirectional; 1171 * EP1 reserved for bulk, two unidirection halves. 1172 */ 1173 if (hw_ep->epnum == 1) 1174 musb->bulk_ep = hw_ep; 1175 /* REVISIT error check: be sure ep0 can both rx and tx ... */ 1176 switch (cfg->style) { 1177 case FIFO_TX: 1178 musb_write_txfifosz(mbase, c_size); 1179 musb_write_txfifoadd(mbase, c_off); 1180 hw_ep->tx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB); 1181 hw_ep->max_packet_sz_tx = maxpacket; 1182 break; 1183 case FIFO_RX: 1184 musb_write_rxfifosz(mbase, c_size); 1185 musb_write_rxfifoadd(mbase, c_off); 1186 hw_ep->rx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB); 1187 hw_ep->max_packet_sz_rx = maxpacket; 1188 break; 1189 case FIFO_RXTX: 1190 musb_write_txfifosz(mbase, c_size); 1191 musb_write_txfifoadd(mbase, c_off); 1192 hw_ep->rx_double_buffered = !!(c_size & MUSB_FIFOSZ_DPB); 1193 hw_ep->max_packet_sz_rx = maxpacket; 1194 1195 musb_write_rxfifosz(mbase, c_size); 1196 musb_write_rxfifoadd(mbase, c_off); 1197 hw_ep->tx_double_buffered = hw_ep->rx_double_buffered; 1198 hw_ep->max_packet_sz_tx = maxpacket; 1199 1200 hw_ep->is_shared_fifo = true; 1201 break; 1202 } 1203 1204 /* NOTE rx and tx endpoint irqs aren't managed separately, 1205 * which happens to be ok 1206 */ 1207 musb->epmask |= (1 << hw_ep->epnum); 1208 1209 return offset + (maxpacket << ((c_size & MUSB_FIFOSZ_DPB) ? 1 : 0)); 1210 } 1211 1212 static struct musb_fifo_cfg __initdata ep0_cfg = { 1213 .style = FIFO_RXTX, .maxpacket = 64, 1214 }; 1215 1216 static int __init ep_config_from_table(struct musb *musb) 1217 { 1218 const struct musb_fifo_cfg *cfg; 1219 unsigned i, n; 1220 int offset; 1221 struct musb_hw_ep *hw_ep = musb->endpoints; 1222 1223 if (musb->config->fifo_cfg) { 1224 cfg = musb->config->fifo_cfg; 1225 n = musb->config->fifo_cfg_size; 1226 goto done; 1227 } 1228 1229 switch (fifo_mode) { 1230 default: 1231 fifo_mode = 0; 1232 /* FALLTHROUGH */ 1233 case 0: 1234 cfg = mode_0_cfg; 1235 n = ARRAY_SIZE(mode_0_cfg); 1236 break; 1237 case 1: 1238 cfg = mode_1_cfg; 1239 n = ARRAY_SIZE(mode_1_cfg); 1240 break; 1241 case 2: 1242 cfg = mode_2_cfg; 1243 n = ARRAY_SIZE(mode_2_cfg); 1244 break; 1245 case 3: 1246 cfg = mode_3_cfg; 1247 n = ARRAY_SIZE(mode_3_cfg); 1248 break; 1249 case 4: 1250 cfg = mode_4_cfg; 1251 n = ARRAY_SIZE(mode_4_cfg); 1252 break; 1253 case 5: 1254 cfg = mode_5_cfg; 1255 n = ARRAY_SIZE(mode_5_cfg); 1256 break; 1257 } 1258 1259 printk(KERN_DEBUG "%s: setup fifo_mode %d\n", 1260 musb_driver_name, fifo_mode); 1261 1262 1263 done: 1264 offset = fifo_setup(musb, hw_ep, &ep0_cfg, 0); 1265 /* assert(offset > 0) */ 1266 1267 /* NOTE: for RTL versions >= 1.400 EPINFO and RAMINFO would 1268 * be better than static musb->config->num_eps and DYN_FIFO_SIZE... 1269 */ 1270 1271 for (i = 0; i < n; i++) { 1272 u8 epn = cfg->hw_ep_num; 1273 1274 if (epn >= musb->config->num_eps) { 1275 pr_debug("%s: invalid ep %d\n", 1276 musb_driver_name, epn); 1277 return -EINVAL; 1278 } 1279 offset = fifo_setup(musb, hw_ep + epn, cfg++, offset); 1280 if (offset < 0) { 1281 pr_debug("%s: mem overrun, ep %d\n", 1282 musb_driver_name, epn); 1283 return -EINVAL; 1284 } 1285 epn++; 1286 musb->nr_endpoints = max(epn, musb->nr_endpoints); 1287 } 1288 1289 printk(KERN_DEBUG "%s: %d/%d max ep, %d/%d memory\n", 1290 musb_driver_name, 1291 n + 1, musb->config->num_eps * 2 - 1, 1292 offset, (1 << (musb->config->ram_bits + 2))); 1293 1294 if (!musb->bulk_ep) { 1295 pr_debug("%s: missing bulk\n", musb_driver_name); 1296 return -EINVAL; 1297 } 1298 1299 return 0; 1300 } 1301 1302 1303 /* 1304 * ep_config_from_hw - when MUSB_C_DYNFIFO_DEF is false 1305 * @param musb the controller 1306 */ 1307 static int __init ep_config_from_hw(struct musb *musb) 1308 { 1309 u8 epnum = 0; 1310 struct musb_hw_ep *hw_ep; 1311 void *mbase = musb->mregs; 1312 int ret = 0; 1313 1314 dev_dbg(musb->controller, "<== static silicon ep config\n"); 1315 1316 /* FIXME pick up ep0 maxpacket size */ 1317 1318 for (epnum = 1; epnum < musb->config->num_eps; epnum++) { 1319 musb_ep_select(mbase, epnum); 1320 hw_ep = musb->endpoints + epnum; 1321 1322 ret = musb_read_fifosize(musb, hw_ep, epnum); 1323 if (ret < 0) 1324 break; 1325 1326 /* FIXME set up hw_ep->{rx,tx}_double_buffered */ 1327 1328 /* pick an RX/TX endpoint for bulk */ 1329 if (hw_ep->max_packet_sz_tx < 512 1330 || hw_ep->max_packet_sz_rx < 512) 1331 continue; 1332 1333 /* REVISIT: this algorithm is lazy, we should at least 1334 * try to pick a double buffered endpoint. 1335 */ 1336 if (musb->bulk_ep) 1337 continue; 1338 musb->bulk_ep = hw_ep; 1339 } 1340 1341 if (!musb->bulk_ep) { 1342 pr_debug("%s: missing bulk\n", musb_driver_name); 1343 return -EINVAL; 1344 } 1345 1346 return 0; 1347 } 1348 1349 enum { MUSB_CONTROLLER_MHDRC, MUSB_CONTROLLER_HDRC, }; 1350 1351 /* Initialize MUSB (M)HDRC part of the USB hardware subsystem; 1352 * configure endpoints, or take their config from silicon 1353 */ 1354 static int __init musb_core_init(u16 musb_type, struct musb *musb) 1355 { 1356 u8 reg; 1357 char *type; 1358 char aInfo[90], aRevision[32], aDate[12]; 1359 void __iomem *mbase = musb->mregs; 1360 int status = 0; 1361 int i; 1362 1363 /* log core options (read using indexed model) */ 1364 reg = musb_read_configdata(mbase); 1365 1366 strcpy(aInfo, (reg & MUSB_CONFIGDATA_UTMIDW) ? "UTMI-16" : "UTMI-8"); 1367 if (reg & MUSB_CONFIGDATA_DYNFIFO) { 1368 strcat(aInfo, ", dyn FIFOs"); 1369 musb->dyn_fifo = true; 1370 } 1371 if (reg & MUSB_CONFIGDATA_MPRXE) { 1372 strcat(aInfo, ", bulk combine"); 1373 musb->bulk_combine = true; 1374 } 1375 if (reg & MUSB_CONFIGDATA_MPTXE) { 1376 strcat(aInfo, ", bulk split"); 1377 musb->bulk_split = true; 1378 } 1379 if (reg & MUSB_CONFIGDATA_HBRXE) { 1380 strcat(aInfo, ", HB-ISO Rx"); 1381 musb->hb_iso_rx = true; 1382 } 1383 if (reg & MUSB_CONFIGDATA_HBTXE) { 1384 strcat(aInfo, ", HB-ISO Tx"); 1385 musb->hb_iso_tx = true; 1386 } 1387 if (reg & MUSB_CONFIGDATA_SOFTCONE) 1388 strcat(aInfo, ", SoftConn"); 1389 1390 printk(KERN_DEBUG "%s: ConfigData=0x%02x (%s)\n", 1391 musb_driver_name, reg, aInfo); 1392 1393 aDate[0] = 0; 1394 if (MUSB_CONTROLLER_MHDRC == musb_type) { 1395 musb->is_multipoint = 1; 1396 type = "M"; 1397 } else { 1398 musb->is_multipoint = 0; 1399 type = ""; 1400 #ifndef CONFIG_USB_OTG_BLACKLIST_HUB 1401 printk(KERN_ERR 1402 "%s: kernel must blacklist external hubs\n", 1403 musb_driver_name); 1404 #endif 1405 } 1406 1407 /* log release info */ 1408 musb->hwvers = musb_read_hwvers(mbase); 1409 snprintf(aRevision, 32, "%d.%d%s", MUSB_HWVERS_MAJOR(musb->hwvers), 1410 MUSB_HWVERS_MINOR(musb->hwvers), 1411 (musb->hwvers & MUSB_HWVERS_RC) ? "RC" : ""); 1412 printk(KERN_DEBUG "%s: %sHDRC RTL version %s %s\n", 1413 musb_driver_name, type, aRevision, aDate); 1414 1415 /* configure ep0 */ 1416 musb_configure_ep0(musb); 1417 1418 /* discover endpoint configuration */ 1419 musb->nr_endpoints = 1; 1420 musb->epmask = 1; 1421 1422 if (musb->dyn_fifo) 1423 status = ep_config_from_table(musb); 1424 else 1425 status = ep_config_from_hw(musb); 1426 1427 if (status < 0) 1428 return status; 1429 1430 /* finish init, and print endpoint config */ 1431 for (i = 0; i < musb->nr_endpoints; i++) { 1432 struct musb_hw_ep *hw_ep = musb->endpoints + i; 1433 1434 hw_ep->fifo = MUSB_FIFO_OFFSET(i) + mbase; 1435 #ifdef CONFIG_USB_MUSB_TUSB6010 1436 hw_ep->fifo_async = musb->async + 0x400 + MUSB_FIFO_OFFSET(i); 1437 hw_ep->fifo_sync = musb->sync + 0x400 + MUSB_FIFO_OFFSET(i); 1438 hw_ep->fifo_sync_va = 1439 musb->sync_va + 0x400 + MUSB_FIFO_OFFSET(i); 1440 1441 if (i == 0) 1442 hw_ep->conf = mbase - 0x400 + TUSB_EP0_CONF; 1443 else 1444 hw_ep->conf = mbase + 0x400 + (((i - 1) & 0xf) << 2); 1445 #endif 1446 1447 hw_ep->regs = MUSB_EP_OFFSET(i, 0) + mbase; 1448 hw_ep->target_regs = musb_read_target_reg_base(i, mbase); 1449 hw_ep->rx_reinit = 1; 1450 hw_ep->tx_reinit = 1; 1451 1452 if (hw_ep->max_packet_sz_tx) { 1453 dev_dbg(musb->controller, 1454 "%s: hw_ep %d%s, %smax %d\n", 1455 musb_driver_name, i, 1456 hw_ep->is_shared_fifo ? "shared" : "tx", 1457 hw_ep->tx_double_buffered 1458 ? "doublebuffer, " : "", 1459 hw_ep->max_packet_sz_tx); 1460 } 1461 if (hw_ep->max_packet_sz_rx && !hw_ep->is_shared_fifo) { 1462 dev_dbg(musb->controller, 1463 "%s: hw_ep %d%s, %smax %d\n", 1464 musb_driver_name, i, 1465 "rx", 1466 hw_ep->rx_double_buffered 1467 ? "doublebuffer, " : "", 1468 hw_ep->max_packet_sz_rx); 1469 } 1470 if (!(hw_ep->max_packet_sz_tx || hw_ep->max_packet_sz_rx)) 1471 dev_dbg(musb->controller, "hw_ep %d not configured\n", i); 1472 } 1473 1474 return 0; 1475 } 1476 1477 /*-------------------------------------------------------------------------*/ 1478 1479 #if defined(CONFIG_SOC_OMAP2430) || defined(CONFIG_SOC_OMAP3430) || \ 1480 defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_ARCH_U8500) || \ 1481 defined(CONFIG_ARCH_U5500) 1482 1483 static irqreturn_t generic_interrupt(int irq, void *__hci) 1484 { 1485 unsigned long flags; 1486 irqreturn_t retval = IRQ_NONE; 1487 struct musb *musb = __hci; 1488 1489 spin_lock_irqsave(&musb->lock, flags); 1490 1491 musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB); 1492 musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX); 1493 musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX); 1494 1495 if (musb->int_usb || musb->int_tx || musb->int_rx) 1496 retval = musb_interrupt(musb); 1497 1498 spin_unlock_irqrestore(&musb->lock, flags); 1499 1500 return retval; 1501 } 1502 1503 #else 1504 #define generic_interrupt NULL 1505 #endif 1506 1507 /* 1508 * handle all the irqs defined by the HDRC core. for now we expect: other 1509 * irq sources (phy, dma, etc) will be handled first, musb->int_* values 1510 * will be assigned, and the irq will already have been acked. 1511 * 1512 * called in irq context with spinlock held, irqs blocked 1513 */ 1514 irqreturn_t musb_interrupt(struct musb *musb) 1515 { 1516 irqreturn_t retval = IRQ_NONE; 1517 u8 devctl, power; 1518 int ep_num; 1519 u32 reg; 1520 1521 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 1522 power = musb_readb(musb->mregs, MUSB_POWER); 1523 1524 dev_dbg(musb->controller, "** IRQ %s usb%04x tx%04x rx%04x\n", 1525 (devctl & MUSB_DEVCTL_HM) ? "host" : "peripheral", 1526 musb->int_usb, musb->int_tx, musb->int_rx); 1527 1528 /* the core can interrupt us for multiple reasons; docs have 1529 * a generic interrupt flowchart to follow 1530 */ 1531 if (musb->int_usb) 1532 retval |= musb_stage0_irq(musb, musb->int_usb, 1533 devctl, power); 1534 1535 /* "stage 1" is handling endpoint irqs */ 1536 1537 /* handle endpoint 0 first */ 1538 if (musb->int_tx & 1) { 1539 if (devctl & MUSB_DEVCTL_HM) 1540 retval |= musb_h_ep0_irq(musb); 1541 else 1542 retval |= musb_g_ep0_irq(musb); 1543 } 1544 1545 /* RX on endpoints 1-15 */ 1546 reg = musb->int_rx >> 1; 1547 ep_num = 1; 1548 while (reg) { 1549 if (reg & 1) { 1550 /* musb_ep_select(musb->mregs, ep_num); */ 1551 /* REVISIT just retval = ep->rx_irq(...) */ 1552 retval = IRQ_HANDLED; 1553 if (devctl & MUSB_DEVCTL_HM) { 1554 if (is_host_capable()) 1555 musb_host_rx(musb, ep_num); 1556 } else { 1557 if (is_peripheral_capable()) 1558 musb_g_rx(musb, ep_num); 1559 } 1560 } 1561 1562 reg >>= 1; 1563 ep_num++; 1564 } 1565 1566 /* TX on endpoints 1-15 */ 1567 reg = musb->int_tx >> 1; 1568 ep_num = 1; 1569 while (reg) { 1570 if (reg & 1) { 1571 /* musb_ep_select(musb->mregs, ep_num); */ 1572 /* REVISIT just retval |= ep->tx_irq(...) */ 1573 retval = IRQ_HANDLED; 1574 if (devctl & MUSB_DEVCTL_HM) { 1575 if (is_host_capable()) 1576 musb_host_tx(musb, ep_num); 1577 } else { 1578 if (is_peripheral_capable()) 1579 musb_g_tx(musb, ep_num); 1580 } 1581 } 1582 reg >>= 1; 1583 ep_num++; 1584 } 1585 1586 return retval; 1587 } 1588 EXPORT_SYMBOL_GPL(musb_interrupt); 1589 1590 #ifndef CONFIG_MUSB_PIO_ONLY 1591 static int __initdata use_dma = 1; 1592 1593 /* "modprobe ... use_dma=0" etc */ 1594 module_param(use_dma, bool, 0); 1595 MODULE_PARM_DESC(use_dma, "enable/disable use of DMA"); 1596 1597 void musb_dma_completion(struct musb *musb, u8 epnum, u8 transmit) 1598 { 1599 u8 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 1600 1601 /* called with controller lock already held */ 1602 1603 if (!epnum) { 1604 #ifndef CONFIG_USB_TUSB_OMAP_DMA 1605 if (!is_cppi_enabled()) { 1606 /* endpoint 0 */ 1607 if (devctl & MUSB_DEVCTL_HM) 1608 musb_h_ep0_irq(musb); 1609 else 1610 musb_g_ep0_irq(musb); 1611 } 1612 #endif 1613 } else { 1614 /* endpoints 1..15 */ 1615 if (transmit) { 1616 if (devctl & MUSB_DEVCTL_HM) { 1617 if (is_host_capable()) 1618 musb_host_tx(musb, epnum); 1619 } else { 1620 if (is_peripheral_capable()) 1621 musb_g_tx(musb, epnum); 1622 } 1623 } else { 1624 /* receive */ 1625 if (devctl & MUSB_DEVCTL_HM) { 1626 if (is_host_capable()) 1627 musb_host_rx(musb, epnum); 1628 } else { 1629 if (is_peripheral_capable()) 1630 musb_g_rx(musb, epnum); 1631 } 1632 } 1633 } 1634 } 1635 1636 #else 1637 #define use_dma 0 1638 #endif 1639 1640 /*-------------------------------------------------------------------------*/ 1641 1642 #ifdef CONFIG_SYSFS 1643 1644 static ssize_t 1645 musb_mode_show(struct device *dev, struct device_attribute *attr, char *buf) 1646 { 1647 struct musb *musb = dev_to_musb(dev); 1648 unsigned long flags; 1649 int ret = -EINVAL; 1650 1651 spin_lock_irqsave(&musb->lock, flags); 1652 ret = sprintf(buf, "%s\n", otg_state_string(musb->xceiv->state)); 1653 spin_unlock_irqrestore(&musb->lock, flags); 1654 1655 return ret; 1656 } 1657 1658 static ssize_t 1659 musb_mode_store(struct device *dev, struct device_attribute *attr, 1660 const char *buf, size_t n) 1661 { 1662 struct musb *musb = dev_to_musb(dev); 1663 unsigned long flags; 1664 int status; 1665 1666 spin_lock_irqsave(&musb->lock, flags); 1667 if (sysfs_streq(buf, "host")) 1668 status = musb_platform_set_mode(musb, MUSB_HOST); 1669 else if (sysfs_streq(buf, "peripheral")) 1670 status = musb_platform_set_mode(musb, MUSB_PERIPHERAL); 1671 else if (sysfs_streq(buf, "otg")) 1672 status = musb_platform_set_mode(musb, MUSB_OTG); 1673 else 1674 status = -EINVAL; 1675 spin_unlock_irqrestore(&musb->lock, flags); 1676 1677 return (status == 0) ? n : status; 1678 } 1679 static DEVICE_ATTR(mode, 0644, musb_mode_show, musb_mode_store); 1680 1681 static ssize_t 1682 musb_vbus_store(struct device *dev, struct device_attribute *attr, 1683 const char *buf, size_t n) 1684 { 1685 struct musb *musb = dev_to_musb(dev); 1686 unsigned long flags; 1687 unsigned long val; 1688 1689 if (sscanf(buf, "%lu", &val) < 1) { 1690 dev_err(dev, "Invalid VBUS timeout ms value\n"); 1691 return -EINVAL; 1692 } 1693 1694 spin_lock_irqsave(&musb->lock, flags); 1695 /* force T(a_wait_bcon) to be zero/unlimited *OR* valid */ 1696 musb->a_wait_bcon = val ? max_t(int, val, OTG_TIME_A_WAIT_BCON) : 0 ; 1697 if (musb->xceiv->state == OTG_STATE_A_WAIT_BCON) 1698 musb->is_active = 0; 1699 musb_platform_try_idle(musb, jiffies + msecs_to_jiffies(val)); 1700 spin_unlock_irqrestore(&musb->lock, flags); 1701 1702 return n; 1703 } 1704 1705 static ssize_t 1706 musb_vbus_show(struct device *dev, struct device_attribute *attr, char *buf) 1707 { 1708 struct musb *musb = dev_to_musb(dev); 1709 unsigned long flags; 1710 unsigned long val; 1711 int vbus; 1712 1713 spin_lock_irqsave(&musb->lock, flags); 1714 val = musb->a_wait_bcon; 1715 /* FIXME get_vbus_status() is normally #defined as false... 1716 * and is effectively TUSB-specific. 1717 */ 1718 vbus = musb_platform_get_vbus_status(musb); 1719 spin_unlock_irqrestore(&musb->lock, flags); 1720 1721 return sprintf(buf, "Vbus %s, timeout %lu msec\n", 1722 vbus ? "on" : "off", val); 1723 } 1724 static DEVICE_ATTR(vbus, 0644, musb_vbus_show, musb_vbus_store); 1725 1726 /* Gadget drivers can't know that a host is connected so they might want 1727 * to start SRP, but users can. This allows userspace to trigger SRP. 1728 */ 1729 static ssize_t 1730 musb_srp_store(struct device *dev, struct device_attribute *attr, 1731 const char *buf, size_t n) 1732 { 1733 struct musb *musb = dev_to_musb(dev); 1734 unsigned short srp; 1735 1736 if (sscanf(buf, "%hu", &srp) != 1 1737 || (srp != 1)) { 1738 dev_err(dev, "SRP: Value must be 1\n"); 1739 return -EINVAL; 1740 } 1741 1742 if (srp == 1) 1743 musb_g_wakeup(musb); 1744 1745 return n; 1746 } 1747 static DEVICE_ATTR(srp, 0644, NULL, musb_srp_store); 1748 1749 static struct attribute *musb_attributes[] = { 1750 &dev_attr_mode.attr, 1751 &dev_attr_vbus.attr, 1752 &dev_attr_srp.attr, 1753 NULL 1754 }; 1755 1756 static const struct attribute_group musb_attr_group = { 1757 .attrs = musb_attributes, 1758 }; 1759 1760 #endif /* sysfs */ 1761 1762 /* Only used to provide driver mode change events */ 1763 static void musb_irq_work(struct work_struct *data) 1764 { 1765 struct musb *musb = container_of(data, struct musb, irq_work); 1766 static int old_state; 1767 1768 if (musb->xceiv->state != old_state) { 1769 old_state = musb->xceiv->state; 1770 sysfs_notify(&musb->controller->kobj, NULL, "mode"); 1771 } 1772 } 1773 1774 /* -------------------------------------------------------------------------- 1775 * Init support 1776 */ 1777 1778 static struct musb *__init 1779 allocate_instance(struct device *dev, 1780 struct musb_hdrc_config *config, void __iomem *mbase) 1781 { 1782 struct musb *musb; 1783 struct musb_hw_ep *ep; 1784 int epnum; 1785 struct usb_hcd *hcd; 1786 1787 hcd = usb_create_hcd(&musb_hc_driver, dev, dev_name(dev)); 1788 if (!hcd) 1789 return NULL; 1790 /* usbcore sets dev->driver_data to hcd, and sometimes uses that... */ 1791 1792 musb = hcd_to_musb(hcd); 1793 INIT_LIST_HEAD(&musb->control); 1794 INIT_LIST_HEAD(&musb->in_bulk); 1795 INIT_LIST_HEAD(&musb->out_bulk); 1796 1797 hcd->uses_new_polling = 1; 1798 hcd->has_tt = 1; 1799 1800 musb->vbuserr_retry = VBUSERR_RETRY_COUNT; 1801 musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON; 1802 dev_set_drvdata(dev, musb); 1803 musb->mregs = mbase; 1804 musb->ctrl_base = mbase; 1805 musb->nIrq = -ENODEV; 1806 musb->config = config; 1807 BUG_ON(musb->config->num_eps > MUSB_C_NUM_EPS); 1808 for (epnum = 0, ep = musb->endpoints; 1809 epnum < musb->config->num_eps; 1810 epnum++, ep++) { 1811 ep->musb = musb; 1812 ep->epnum = epnum; 1813 } 1814 1815 musb->controller = dev; 1816 1817 return musb; 1818 } 1819 1820 static void musb_free(struct musb *musb) 1821 { 1822 /* this has multiple entry modes. it handles fault cleanup after 1823 * probe(), where things may be partially set up, as well as rmmod 1824 * cleanup after everything's been de-activated. 1825 */ 1826 1827 #ifdef CONFIG_SYSFS 1828 sysfs_remove_group(&musb->controller->kobj, &musb_attr_group); 1829 #endif 1830 1831 musb_gadget_cleanup(musb); 1832 1833 if (musb->nIrq >= 0) { 1834 if (musb->irq_wake) 1835 disable_irq_wake(musb->nIrq); 1836 free_irq(musb->nIrq, musb); 1837 } 1838 if (is_dma_capable() && musb->dma_controller) { 1839 struct dma_controller *c = musb->dma_controller; 1840 1841 (void) c->stop(c); 1842 dma_controller_destroy(c); 1843 } 1844 1845 kfree(musb); 1846 } 1847 1848 /* 1849 * Perform generic per-controller initialization. 1850 * 1851 * @pDevice: the controller (already clocked, etc) 1852 * @nIrq: irq 1853 * @mregs: virtual address of controller registers, 1854 * not yet corrected for platform-specific offsets 1855 */ 1856 static int __init 1857 musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl) 1858 { 1859 int status; 1860 struct musb *musb; 1861 struct musb_hdrc_platform_data *plat = dev->platform_data; 1862 1863 /* The driver might handle more features than the board; OK. 1864 * Fail when the board needs a feature that's not enabled. 1865 */ 1866 if (!plat) { 1867 dev_dbg(dev, "no platform_data?\n"); 1868 status = -ENODEV; 1869 goto fail0; 1870 } 1871 1872 /* allocate */ 1873 musb = allocate_instance(dev, plat->config, ctrl); 1874 if (!musb) { 1875 status = -ENOMEM; 1876 goto fail0; 1877 } 1878 1879 pm_runtime_use_autosuspend(musb->controller); 1880 pm_runtime_set_autosuspend_delay(musb->controller, 200); 1881 pm_runtime_enable(musb->controller); 1882 1883 spin_lock_init(&musb->lock); 1884 musb->board_mode = plat->mode; 1885 musb->board_set_power = plat->set_power; 1886 musb->min_power = plat->min_power; 1887 musb->ops = plat->platform_ops; 1888 1889 /* The musb_platform_init() call: 1890 * - adjusts musb->mregs and musb->isr if needed, 1891 * - may initialize an integrated tranceiver 1892 * - initializes musb->xceiv, usually by otg_get_transceiver() 1893 * - stops powering VBUS 1894 * 1895 * There are various transceiver configurations. Blackfin, 1896 * DaVinci, TUSB60x0, and others integrate them. OMAP3 uses 1897 * external/discrete ones in various flavors (twl4030 family, 1898 * isp1504, non-OTG, etc) mostly hooking up through ULPI. 1899 */ 1900 musb->isr = generic_interrupt; 1901 status = musb_platform_init(musb); 1902 if (status < 0) 1903 goto fail1; 1904 1905 if (!musb->isr) { 1906 status = -ENODEV; 1907 goto fail3; 1908 } 1909 1910 if (!musb->xceiv->io_ops) { 1911 musb->xceiv->io_priv = musb->mregs; 1912 musb->xceiv->io_ops = &musb_ulpi_access; 1913 } 1914 1915 #ifndef CONFIG_MUSB_PIO_ONLY 1916 if (use_dma && dev->dma_mask) { 1917 struct dma_controller *c; 1918 1919 c = dma_controller_create(musb, musb->mregs); 1920 musb->dma_controller = c; 1921 if (c) 1922 (void) c->start(c); 1923 } 1924 #endif 1925 /* ideally this would be abstracted in platform setup */ 1926 if (!is_dma_capable() || !musb->dma_controller) 1927 dev->dma_mask = NULL; 1928 1929 /* be sure interrupts are disabled before connecting ISR */ 1930 musb_platform_disable(musb); 1931 musb_generic_disable(musb); 1932 1933 /* setup musb parts of the core (especially endpoints) */ 1934 status = musb_core_init(plat->config->multipoint 1935 ? MUSB_CONTROLLER_MHDRC 1936 : MUSB_CONTROLLER_HDRC, musb); 1937 if (status < 0) 1938 goto fail3; 1939 1940 setup_timer(&musb->otg_timer, musb_otg_timer_func, (unsigned long) musb); 1941 1942 /* Init IRQ workqueue before request_irq */ 1943 INIT_WORK(&musb->irq_work, musb_irq_work); 1944 1945 /* attach to the IRQ */ 1946 if (request_irq(nIrq, musb->isr, 0, dev_name(dev), musb)) { 1947 dev_err(dev, "request_irq %d failed!\n", nIrq); 1948 status = -ENODEV; 1949 goto fail3; 1950 } 1951 musb->nIrq = nIrq; 1952 /* FIXME this handles wakeup irqs wrong */ 1953 if (enable_irq_wake(nIrq) == 0) { 1954 musb->irq_wake = 1; 1955 device_init_wakeup(dev, 1); 1956 } else { 1957 musb->irq_wake = 0; 1958 } 1959 1960 /* host side needs more setup */ 1961 if (is_host_enabled(musb)) { 1962 struct usb_hcd *hcd = musb_to_hcd(musb); 1963 1964 otg_set_host(musb->xceiv, &hcd->self); 1965 1966 if (is_otg_enabled(musb)) 1967 hcd->self.otg_port = 1; 1968 musb->xceiv->host = &hcd->self; 1969 hcd->power_budget = 2 * (plat->power ? : 250); 1970 1971 /* program PHY to use external vBus if required */ 1972 if (plat->extvbus) { 1973 u8 busctl = musb_read_ulpi_buscontrol(musb->mregs); 1974 busctl |= MUSB_ULPI_USE_EXTVBUS; 1975 musb_write_ulpi_buscontrol(musb->mregs, busctl); 1976 } 1977 } 1978 1979 /* For the host-only role, we can activate right away. 1980 * (We expect the ID pin to be forcibly grounded!!) 1981 * Otherwise, wait till the gadget driver hooks up. 1982 */ 1983 if (!is_otg_enabled(musb) && is_host_enabled(musb)) { 1984 struct usb_hcd *hcd = musb_to_hcd(musb); 1985 1986 MUSB_HST_MODE(musb); 1987 musb->xceiv->default_a = 1; 1988 musb->xceiv->state = OTG_STATE_A_IDLE; 1989 1990 status = usb_add_hcd(musb_to_hcd(musb), -1, 0); 1991 1992 hcd->self.uses_pio_for_control = 1; 1993 dev_dbg(musb->controller, "%s mode, status %d, devctl %02x %c\n", 1994 "HOST", status, 1995 musb_readb(musb->mregs, MUSB_DEVCTL), 1996 (musb_readb(musb->mregs, MUSB_DEVCTL) 1997 & MUSB_DEVCTL_BDEVICE 1998 ? 'B' : 'A')); 1999 2000 } else /* peripheral is enabled */ { 2001 MUSB_DEV_MODE(musb); 2002 musb->xceiv->default_a = 0; 2003 musb->xceiv->state = OTG_STATE_B_IDLE; 2004 2005 status = musb_gadget_setup(musb); 2006 2007 dev_dbg(musb->controller, "%s mode, status %d, dev%02x\n", 2008 is_otg_enabled(musb) ? "OTG" : "PERIPHERAL", 2009 status, 2010 musb_readb(musb->mregs, MUSB_DEVCTL)); 2011 2012 } 2013 if (status < 0) 2014 goto fail3; 2015 2016 pm_runtime_put(musb->controller); 2017 2018 status = musb_init_debugfs(musb); 2019 if (status < 0) 2020 goto fail4; 2021 2022 #ifdef CONFIG_SYSFS 2023 status = sysfs_create_group(&musb->controller->kobj, &musb_attr_group); 2024 if (status) 2025 goto fail5; 2026 #endif 2027 2028 dev_info(dev, "USB %s mode controller at %p using %s, IRQ %d\n", 2029 ({char *s; 2030 switch (musb->board_mode) { 2031 case MUSB_HOST: s = "Host"; break; 2032 case MUSB_PERIPHERAL: s = "Peripheral"; break; 2033 default: s = "OTG"; break; 2034 }; s; }), 2035 ctrl, 2036 (is_dma_capable() && musb->dma_controller) 2037 ? "DMA" : "PIO", 2038 musb->nIrq); 2039 2040 return 0; 2041 2042 fail5: 2043 musb_exit_debugfs(musb); 2044 2045 fail4: 2046 if (!is_otg_enabled(musb) && is_host_enabled(musb)) 2047 usb_remove_hcd(musb_to_hcd(musb)); 2048 else 2049 musb_gadget_cleanup(musb); 2050 2051 fail3: 2052 if (musb->irq_wake) 2053 device_init_wakeup(dev, 0); 2054 musb_platform_exit(musb); 2055 2056 fail1: 2057 dev_err(musb->controller, 2058 "musb_init_controller failed with status %d\n", status); 2059 2060 musb_free(musb); 2061 2062 fail0: 2063 2064 return status; 2065 2066 } 2067 2068 /*-------------------------------------------------------------------------*/ 2069 2070 /* all implementations (PCI bridge to FPGA, VLYNQ, etc) should just 2071 * bridge to a platform device; this driver then suffices. 2072 */ 2073 2074 #ifndef CONFIG_MUSB_PIO_ONLY 2075 static u64 *orig_dma_mask; 2076 #endif 2077 2078 static int __init musb_probe(struct platform_device *pdev) 2079 { 2080 struct device *dev = &pdev->dev; 2081 int irq = platform_get_irq_byname(pdev, "mc"); 2082 int status; 2083 struct resource *iomem; 2084 void __iomem *base; 2085 2086 iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2087 if (!iomem || irq <= 0) 2088 return -ENODEV; 2089 2090 base = ioremap(iomem->start, resource_size(iomem)); 2091 if (!base) { 2092 dev_err(dev, "ioremap failed\n"); 2093 return -ENOMEM; 2094 } 2095 2096 #ifndef CONFIG_MUSB_PIO_ONLY 2097 /* clobbered by use_dma=n */ 2098 orig_dma_mask = dev->dma_mask; 2099 #endif 2100 status = musb_init_controller(dev, irq, base); 2101 if (status < 0) 2102 iounmap(base); 2103 2104 return status; 2105 } 2106 2107 static int __exit musb_remove(struct platform_device *pdev) 2108 { 2109 struct musb *musb = dev_to_musb(&pdev->dev); 2110 void __iomem *ctrl_base = musb->ctrl_base; 2111 2112 /* this gets called on rmmod. 2113 * - Host mode: host may still be active 2114 * - Peripheral mode: peripheral is deactivated (or never-activated) 2115 * - OTG mode: both roles are deactivated (or never-activated) 2116 */ 2117 pm_runtime_get_sync(musb->controller); 2118 musb_exit_debugfs(musb); 2119 musb_shutdown(pdev); 2120 2121 pm_runtime_put(musb->controller); 2122 musb_free(musb); 2123 iounmap(ctrl_base); 2124 device_init_wakeup(&pdev->dev, 0); 2125 #ifndef CONFIG_MUSB_PIO_ONLY 2126 pdev->dev.dma_mask = orig_dma_mask; 2127 #endif 2128 return 0; 2129 } 2130 2131 #ifdef CONFIG_PM 2132 2133 static void musb_save_context(struct musb *musb) 2134 { 2135 int i; 2136 void __iomem *musb_base = musb->mregs; 2137 void __iomem *epio; 2138 2139 if (is_host_enabled(musb)) { 2140 musb->context.frame = musb_readw(musb_base, MUSB_FRAME); 2141 musb->context.testmode = musb_readb(musb_base, MUSB_TESTMODE); 2142 musb->context.busctl = musb_read_ulpi_buscontrol(musb->mregs); 2143 } 2144 musb->context.power = musb_readb(musb_base, MUSB_POWER); 2145 musb->context.intrtxe = musb_readw(musb_base, MUSB_INTRTXE); 2146 musb->context.intrrxe = musb_readw(musb_base, MUSB_INTRRXE); 2147 musb->context.intrusbe = musb_readb(musb_base, MUSB_INTRUSBE); 2148 musb->context.index = musb_readb(musb_base, MUSB_INDEX); 2149 musb->context.devctl = musb_readb(musb_base, MUSB_DEVCTL); 2150 2151 for (i = 0; i < musb->config->num_eps; ++i) { 2152 struct musb_hw_ep *hw_ep; 2153 2154 hw_ep = &musb->endpoints[i]; 2155 if (!hw_ep) 2156 continue; 2157 2158 epio = hw_ep->regs; 2159 if (!epio) 2160 continue; 2161 2162 musb->context.index_regs[i].txmaxp = 2163 musb_readw(epio, MUSB_TXMAXP); 2164 musb->context.index_regs[i].txcsr = 2165 musb_readw(epio, MUSB_TXCSR); 2166 musb->context.index_regs[i].rxmaxp = 2167 musb_readw(epio, MUSB_RXMAXP); 2168 musb->context.index_regs[i].rxcsr = 2169 musb_readw(epio, MUSB_RXCSR); 2170 2171 if (musb->dyn_fifo) { 2172 musb->context.index_regs[i].txfifoadd = 2173 musb_read_txfifoadd(musb_base); 2174 musb->context.index_regs[i].rxfifoadd = 2175 musb_read_rxfifoadd(musb_base); 2176 musb->context.index_regs[i].txfifosz = 2177 musb_read_txfifosz(musb_base); 2178 musb->context.index_regs[i].rxfifosz = 2179 musb_read_rxfifosz(musb_base); 2180 } 2181 if (is_host_enabled(musb)) { 2182 musb->context.index_regs[i].txtype = 2183 musb_readb(epio, MUSB_TXTYPE); 2184 musb->context.index_regs[i].txinterval = 2185 musb_readb(epio, MUSB_TXINTERVAL); 2186 musb->context.index_regs[i].rxtype = 2187 musb_readb(epio, MUSB_RXTYPE); 2188 musb->context.index_regs[i].rxinterval = 2189 musb_readb(epio, MUSB_RXINTERVAL); 2190 2191 musb->context.index_regs[i].txfunaddr = 2192 musb_read_txfunaddr(musb_base, i); 2193 musb->context.index_regs[i].txhubaddr = 2194 musb_read_txhubaddr(musb_base, i); 2195 musb->context.index_regs[i].txhubport = 2196 musb_read_txhubport(musb_base, i); 2197 2198 musb->context.index_regs[i].rxfunaddr = 2199 musb_read_rxfunaddr(musb_base, i); 2200 musb->context.index_regs[i].rxhubaddr = 2201 musb_read_rxhubaddr(musb_base, i); 2202 musb->context.index_regs[i].rxhubport = 2203 musb_read_rxhubport(musb_base, i); 2204 } 2205 } 2206 } 2207 2208 static void musb_restore_context(struct musb *musb) 2209 { 2210 int i; 2211 void __iomem *musb_base = musb->mregs; 2212 void __iomem *ep_target_regs; 2213 void __iomem *epio; 2214 2215 if (is_host_enabled(musb)) { 2216 musb_writew(musb_base, MUSB_FRAME, musb->context.frame); 2217 musb_writeb(musb_base, MUSB_TESTMODE, musb->context.testmode); 2218 musb_write_ulpi_buscontrol(musb->mregs, musb->context.busctl); 2219 } 2220 musb_writeb(musb_base, MUSB_POWER, musb->context.power); 2221 musb_writew(musb_base, MUSB_INTRTXE, musb->context.intrtxe); 2222 musb_writew(musb_base, MUSB_INTRRXE, musb->context.intrrxe); 2223 musb_writeb(musb_base, MUSB_INTRUSBE, musb->context.intrusbe); 2224 musb_writeb(musb_base, MUSB_DEVCTL, musb->context.devctl); 2225 2226 for (i = 0; i < musb->config->num_eps; ++i) { 2227 struct musb_hw_ep *hw_ep; 2228 2229 hw_ep = &musb->endpoints[i]; 2230 if (!hw_ep) 2231 continue; 2232 2233 epio = hw_ep->regs; 2234 if (!epio) 2235 continue; 2236 2237 musb_writew(epio, MUSB_TXMAXP, 2238 musb->context.index_regs[i].txmaxp); 2239 musb_writew(epio, MUSB_TXCSR, 2240 musb->context.index_regs[i].txcsr); 2241 musb_writew(epio, MUSB_RXMAXP, 2242 musb->context.index_regs[i].rxmaxp); 2243 musb_writew(epio, MUSB_RXCSR, 2244 musb->context.index_regs[i].rxcsr); 2245 2246 if (musb->dyn_fifo) { 2247 musb_write_txfifosz(musb_base, 2248 musb->context.index_regs[i].txfifosz); 2249 musb_write_rxfifosz(musb_base, 2250 musb->context.index_regs[i].rxfifosz); 2251 musb_write_txfifoadd(musb_base, 2252 musb->context.index_regs[i].txfifoadd); 2253 musb_write_rxfifoadd(musb_base, 2254 musb->context.index_regs[i].rxfifoadd); 2255 } 2256 2257 if (is_host_enabled(musb)) { 2258 musb_writeb(epio, MUSB_TXTYPE, 2259 musb->context.index_regs[i].txtype); 2260 musb_writeb(epio, MUSB_TXINTERVAL, 2261 musb->context.index_regs[i].txinterval); 2262 musb_writeb(epio, MUSB_RXTYPE, 2263 musb->context.index_regs[i].rxtype); 2264 musb_writeb(epio, MUSB_RXINTERVAL, 2265 2266 musb->context.index_regs[i].rxinterval); 2267 musb_write_txfunaddr(musb_base, i, 2268 musb->context.index_regs[i].txfunaddr); 2269 musb_write_txhubaddr(musb_base, i, 2270 musb->context.index_regs[i].txhubaddr); 2271 musb_write_txhubport(musb_base, i, 2272 musb->context.index_regs[i].txhubport); 2273 2274 ep_target_regs = 2275 musb_read_target_reg_base(i, musb_base); 2276 2277 musb_write_rxfunaddr(ep_target_regs, 2278 musb->context.index_regs[i].rxfunaddr); 2279 musb_write_rxhubaddr(ep_target_regs, 2280 musb->context.index_regs[i].rxhubaddr); 2281 musb_write_rxhubport(ep_target_regs, 2282 musb->context.index_regs[i].rxhubport); 2283 } 2284 } 2285 musb_writeb(musb_base, MUSB_INDEX, musb->context.index); 2286 } 2287 2288 static int musb_suspend(struct device *dev) 2289 { 2290 struct musb *musb = dev_to_musb(dev); 2291 unsigned long flags; 2292 2293 spin_lock_irqsave(&musb->lock, flags); 2294 2295 if (is_peripheral_active(musb)) { 2296 /* FIXME force disconnect unless we know USB will wake 2297 * the system up quickly enough to respond ... 2298 */ 2299 } else if (is_host_active(musb)) { 2300 /* we know all the children are suspended; sometimes 2301 * they will even be wakeup-enabled. 2302 */ 2303 } 2304 2305 musb_save_context(musb); 2306 2307 spin_unlock_irqrestore(&musb->lock, flags); 2308 return 0; 2309 } 2310 2311 static int musb_resume_noirq(struct device *dev) 2312 { 2313 struct musb *musb = dev_to_musb(dev); 2314 2315 musb_restore_context(musb); 2316 2317 /* for static cmos like DaVinci, register values were preserved 2318 * unless for some reason the whole soc powered down or the USB 2319 * module got reset through the PSC (vs just being disabled). 2320 */ 2321 return 0; 2322 } 2323 2324 static int musb_runtime_suspend(struct device *dev) 2325 { 2326 struct musb *musb = dev_to_musb(dev); 2327 2328 musb_save_context(musb); 2329 2330 return 0; 2331 } 2332 2333 static int musb_runtime_resume(struct device *dev) 2334 { 2335 struct musb *musb = dev_to_musb(dev); 2336 static int first = 1; 2337 2338 /* 2339 * When pm_runtime_get_sync called for the first time in driver 2340 * init, some of the structure is still not initialized which is 2341 * used in restore function. But clock needs to be 2342 * enabled before any register access, so 2343 * pm_runtime_get_sync has to be called. 2344 * Also context restore without save does not make 2345 * any sense 2346 */ 2347 if (!first) 2348 musb_restore_context(musb); 2349 first = 0; 2350 2351 return 0; 2352 } 2353 2354 static const struct dev_pm_ops musb_dev_pm_ops = { 2355 .suspend = musb_suspend, 2356 .resume_noirq = musb_resume_noirq, 2357 .runtime_suspend = musb_runtime_suspend, 2358 .runtime_resume = musb_runtime_resume, 2359 }; 2360 2361 #define MUSB_DEV_PM_OPS (&musb_dev_pm_ops) 2362 #else 2363 #define MUSB_DEV_PM_OPS NULL 2364 #endif 2365 2366 static struct platform_driver musb_driver = { 2367 .driver = { 2368 .name = (char *)musb_driver_name, 2369 .bus = &platform_bus_type, 2370 .owner = THIS_MODULE, 2371 .pm = MUSB_DEV_PM_OPS, 2372 }, 2373 .remove = __exit_p(musb_remove), 2374 .shutdown = musb_shutdown, 2375 }; 2376 2377 /*-------------------------------------------------------------------------*/ 2378 2379 static int __init musb_init(void) 2380 { 2381 if (usb_disabled()) 2382 return 0; 2383 2384 pr_info("%s: version " MUSB_VERSION ", " 2385 "?dma?" 2386 ", " 2387 "otg (peripheral+host)", 2388 musb_driver_name); 2389 return platform_driver_probe(&musb_driver, musb_probe); 2390 } 2391 2392 /* make us init after usbcore and i2c (transceivers, regulators, etc) 2393 * and before usb gadget and host-side drivers start to register 2394 */ 2395 fs_initcall(musb_init); 2396 2397 static void __exit musb_cleanup(void) 2398 { 2399 platform_driver_unregister(&musb_driver); 2400 } 2401 module_exit(musb_cleanup); 2402