1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Texas Instruments DA8xx/OMAP-L1x "glue layer" 4 * 5 * Copyright (c) 2008-2009 MontaVista Software, Inc. <source@mvista.com> 6 * 7 * Based on the DaVinci "glue layer" code. 8 * Copyright (C) 2005-2006 by Texas Instruments 9 * 10 * DT support 11 * Copyright (c) 2016 Petr Kulhavy <petr@barix.com> 12 * 13 * This file is part of the Inventra Controller Driver for Linux. 14 */ 15 16 #include <linux/module.h> 17 #include <linux/clk.h> 18 #include <linux/err.h> 19 #include <linux/io.h> 20 #include <linux/of_platform.h> 21 #include <linux/phy/phy.h> 22 #include <linux/platform_device.h> 23 #include <linux/dma-mapping.h> 24 #include <linux/usb/usb_phy_generic.h> 25 26 #include "musb_core.h" 27 28 /* 29 * DA8XX specific definitions 30 */ 31 32 /* USB 2.0 OTG module registers */ 33 #define DA8XX_USB_REVISION_REG 0x00 34 #define DA8XX_USB_CTRL_REG 0x04 35 #define DA8XX_USB_STAT_REG 0x08 36 #define DA8XX_USB_EMULATION_REG 0x0c 37 #define DA8XX_USB_SRP_FIX_TIME_REG 0x18 38 #define DA8XX_USB_INTR_SRC_REG 0x20 39 #define DA8XX_USB_INTR_SRC_SET_REG 0x24 40 #define DA8XX_USB_INTR_SRC_CLEAR_REG 0x28 41 #define DA8XX_USB_INTR_MASK_REG 0x2c 42 #define DA8XX_USB_INTR_MASK_SET_REG 0x30 43 #define DA8XX_USB_INTR_MASK_CLEAR_REG 0x34 44 #define DA8XX_USB_INTR_SRC_MASKED_REG 0x38 45 #define DA8XX_USB_END_OF_INTR_REG 0x3c 46 #define DA8XX_USB_GENERIC_RNDIS_EP_SIZE_REG(n) (0x50 + (((n) - 1) << 2)) 47 48 /* Control register bits */ 49 #define DA8XX_SOFT_RESET_MASK 1 50 51 #define DA8XX_USB_TX_EP_MASK 0x1f /* EP0 + 4 Tx EPs */ 52 #define DA8XX_USB_RX_EP_MASK 0x1e /* 4 Rx EPs */ 53 54 /* USB interrupt register bits */ 55 #define DA8XX_INTR_USB_SHIFT 16 56 #define DA8XX_INTR_USB_MASK (0x1ff << DA8XX_INTR_USB_SHIFT) /* 8 Mentor */ 57 /* interrupts and DRVVBUS interrupt */ 58 #define DA8XX_INTR_DRVVBUS 0x100 59 #define DA8XX_INTR_RX_SHIFT 8 60 #define DA8XX_INTR_RX_MASK (DA8XX_USB_RX_EP_MASK << DA8XX_INTR_RX_SHIFT) 61 #define DA8XX_INTR_TX_SHIFT 0 62 #define DA8XX_INTR_TX_MASK (DA8XX_USB_TX_EP_MASK << DA8XX_INTR_TX_SHIFT) 63 64 #define DA8XX_MENTOR_CORE_OFFSET 0x400 65 66 struct da8xx_glue { 67 struct device *dev; 68 struct platform_device *musb; 69 struct platform_device *usb_phy; 70 struct clk *clk; 71 struct phy *phy; 72 }; 73 74 /* 75 * Because we don't set CTRL.UINT, it's "important" to: 76 * - not read/write INTRUSB/INTRUSBE (except during 77 * initial setup, as a workaround); 78 * - use INTSET/INTCLR instead. 79 */ 80 81 /** 82 * da8xx_musb_enable - enable interrupts 83 */ 84 static void da8xx_musb_enable(struct musb *musb) 85 { 86 void __iomem *reg_base = musb->ctrl_base; 87 u32 mask; 88 89 /* Workaround: setup IRQs through both register sets. */ 90 mask = ((musb->epmask & DA8XX_USB_TX_EP_MASK) << DA8XX_INTR_TX_SHIFT) | 91 ((musb->epmask & DA8XX_USB_RX_EP_MASK) << DA8XX_INTR_RX_SHIFT) | 92 DA8XX_INTR_USB_MASK; 93 musb_writel(reg_base, DA8XX_USB_INTR_MASK_SET_REG, mask); 94 95 /* Force the DRVVBUS IRQ so we can start polling for ID change. */ 96 musb_writel(reg_base, DA8XX_USB_INTR_SRC_SET_REG, 97 DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT); 98 } 99 100 /** 101 * da8xx_musb_disable - disable HDRC and flush interrupts 102 */ 103 static void da8xx_musb_disable(struct musb *musb) 104 { 105 void __iomem *reg_base = musb->ctrl_base; 106 107 musb_writel(reg_base, DA8XX_USB_INTR_MASK_CLEAR_REG, 108 DA8XX_INTR_USB_MASK | 109 DA8XX_INTR_TX_MASK | DA8XX_INTR_RX_MASK); 110 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 111 } 112 113 #define portstate(stmt) stmt 114 115 static void da8xx_musb_set_vbus(struct musb *musb, int is_on) 116 { 117 WARN_ON(is_on && is_peripheral_active(musb)); 118 } 119 120 #define POLL_SECONDS 2 121 122 static void otg_timer(struct timer_list *t) 123 { 124 struct musb *musb = from_timer(musb, t, dev_timer); 125 void __iomem *mregs = musb->mregs; 126 u8 devctl; 127 unsigned long flags; 128 129 /* 130 * We poll because DaVinci's won't expose several OTG-critical 131 * status change events (from the transceiver) otherwise. 132 */ 133 devctl = musb_readb(mregs, MUSB_DEVCTL); 134 dev_dbg(musb->controller, "Poll devctl %02x (%s)\n", devctl, 135 usb_otg_state_string(musb->xceiv->otg->state)); 136 137 spin_lock_irqsave(&musb->lock, flags); 138 switch (musb->xceiv->otg->state) { 139 case OTG_STATE_A_WAIT_BCON: 140 devctl &= ~MUSB_DEVCTL_SESSION; 141 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); 142 143 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 144 if (devctl & MUSB_DEVCTL_BDEVICE) { 145 musb->xceiv->otg->state = OTG_STATE_B_IDLE; 146 MUSB_DEV_MODE(musb); 147 } else { 148 musb->xceiv->otg->state = OTG_STATE_A_IDLE; 149 MUSB_HST_MODE(musb); 150 } 151 break; 152 case OTG_STATE_A_WAIT_VFALL: 153 /* 154 * Wait till VBUS falls below SessionEnd (~0.2 V); the 1.3 155 * RTL seems to mis-handle session "start" otherwise (or in 156 * our case "recover"), in routine "VBUS was valid by the time 157 * VBUSERR got reported during enumeration" cases. 158 */ 159 if (devctl & MUSB_DEVCTL_VBUS) { 160 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 161 break; 162 } 163 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE; 164 musb_writel(musb->ctrl_base, DA8XX_USB_INTR_SRC_SET_REG, 165 MUSB_INTR_VBUSERROR << DA8XX_INTR_USB_SHIFT); 166 break; 167 case OTG_STATE_B_IDLE: 168 /* 169 * There's no ID-changed IRQ, so we have no good way to tell 170 * when to switch to the A-Default state machine (by setting 171 * the DEVCTL.Session bit). 172 * 173 * Workaround: whenever we're in B_IDLE, try setting the 174 * session flag every few seconds. If it works, ID was 175 * grounded and we're now in the A-Default state machine. 176 * 177 * NOTE: setting the session flag is _supposed_ to trigger 178 * SRP but clearly it doesn't. 179 */ 180 musb_writeb(mregs, MUSB_DEVCTL, devctl | MUSB_DEVCTL_SESSION); 181 devctl = musb_readb(mregs, MUSB_DEVCTL); 182 if (devctl & MUSB_DEVCTL_BDEVICE) 183 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 184 else 185 musb->xceiv->otg->state = OTG_STATE_A_IDLE; 186 break; 187 default: 188 break; 189 } 190 spin_unlock_irqrestore(&musb->lock, flags); 191 } 192 193 static void da8xx_musb_try_idle(struct musb *musb, unsigned long timeout) 194 { 195 static unsigned long last_timer; 196 197 if (timeout == 0) 198 timeout = jiffies + msecs_to_jiffies(3); 199 200 /* Never idle if active, or when VBUS timeout is not set as host */ 201 if (musb->is_active || (musb->a_wait_bcon == 0 && 202 musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON)) { 203 dev_dbg(musb->controller, "%s active, deleting timer\n", 204 usb_otg_state_string(musb->xceiv->otg->state)); 205 del_timer(&musb->dev_timer); 206 last_timer = jiffies; 207 return; 208 } 209 210 if (time_after(last_timer, timeout) && timer_pending(&musb->dev_timer)) { 211 dev_dbg(musb->controller, "Longer idle timer already pending, ignoring...\n"); 212 return; 213 } 214 last_timer = timeout; 215 216 dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n", 217 usb_otg_state_string(musb->xceiv->otg->state), 218 jiffies_to_msecs(timeout - jiffies)); 219 mod_timer(&musb->dev_timer, timeout); 220 } 221 222 static irqreturn_t da8xx_musb_interrupt(int irq, void *hci) 223 { 224 struct musb *musb = hci; 225 void __iomem *reg_base = musb->ctrl_base; 226 struct usb_otg *otg = musb->xceiv->otg; 227 unsigned long flags; 228 irqreturn_t ret = IRQ_NONE; 229 u32 status; 230 231 spin_lock_irqsave(&musb->lock, flags); 232 233 /* 234 * NOTE: DA8XX shadows the Mentor IRQs. Don't manage them through 235 * the Mentor registers (except for setup), use the TI ones and EOI. 236 */ 237 238 /* Acknowledge and handle non-CPPI interrupts */ 239 status = musb_readl(reg_base, DA8XX_USB_INTR_SRC_MASKED_REG); 240 if (!status) 241 goto eoi; 242 243 musb_writel(reg_base, DA8XX_USB_INTR_SRC_CLEAR_REG, status); 244 dev_dbg(musb->controller, "USB IRQ %08x\n", status); 245 246 musb->int_rx = (status & DA8XX_INTR_RX_MASK) >> DA8XX_INTR_RX_SHIFT; 247 musb->int_tx = (status & DA8XX_INTR_TX_MASK) >> DA8XX_INTR_TX_SHIFT; 248 musb->int_usb = (status & DA8XX_INTR_USB_MASK) >> DA8XX_INTR_USB_SHIFT; 249 250 /* 251 * DRVVBUS IRQs are the only proxy we have (a very poor one!) for 252 * DA8xx's missing ID change IRQ. We need an ID change IRQ to 253 * switch appropriately between halves of the OTG state machine. 254 * Managing DEVCTL.Session per Mentor docs requires that we know its 255 * value but DEVCTL.BDevice is invalid without DEVCTL.Session set. 256 * Also, DRVVBUS pulses for SRP (but not at 5 V)... 257 */ 258 if (status & (DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT)) { 259 int drvvbus = musb_readl(reg_base, DA8XX_USB_STAT_REG); 260 void __iomem *mregs = musb->mregs; 261 u8 devctl = musb_readb(mregs, MUSB_DEVCTL); 262 int err; 263 264 err = musb->int_usb & MUSB_INTR_VBUSERROR; 265 if (err) { 266 /* 267 * The Mentor core doesn't debounce VBUS as needed 268 * to cope with device connect current spikes. This 269 * means it's not uncommon for bus-powered devices 270 * to get VBUS errors during enumeration. 271 * 272 * This is a workaround, but newer RTL from Mentor 273 * seems to allow a better one: "re"-starting sessions 274 * without waiting for VBUS to stop registering in 275 * devctl. 276 */ 277 musb->int_usb &= ~MUSB_INTR_VBUSERROR; 278 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL; 279 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 280 WARNING("VBUS error workaround (delay coming)\n"); 281 } else if (drvvbus) { 282 MUSB_HST_MODE(musb); 283 otg->default_a = 1; 284 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE; 285 portstate(musb->port1_status |= USB_PORT_STAT_POWER); 286 del_timer(&musb->dev_timer); 287 } else if (!(musb->int_usb & MUSB_INTR_BABBLE)) { 288 /* 289 * When babble condition happens, drvvbus interrupt 290 * is also generated. Ignore this drvvbus interrupt 291 * and let babble interrupt handler recovers the 292 * controller; otherwise, the host-mode flag is lost 293 * due to the MUSB_DEV_MODE() call below and babble 294 * recovery logic will not be called. 295 */ 296 musb->is_active = 0; 297 MUSB_DEV_MODE(musb); 298 otg->default_a = 0; 299 musb->xceiv->otg->state = OTG_STATE_B_IDLE; 300 portstate(musb->port1_status &= ~USB_PORT_STAT_POWER); 301 } 302 303 dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n", 304 drvvbus ? "on" : "off", 305 usb_otg_state_string(musb->xceiv->otg->state), 306 err ? " ERROR" : "", 307 devctl); 308 ret = IRQ_HANDLED; 309 } 310 311 if (musb->int_tx || musb->int_rx || musb->int_usb) 312 ret |= musb_interrupt(musb); 313 314 eoi: 315 /* EOI needs to be written for the IRQ to be re-asserted. */ 316 if (ret == IRQ_HANDLED || status) 317 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 318 319 /* Poll for ID change */ 320 if (musb->xceiv->otg->state == OTG_STATE_B_IDLE) 321 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 322 323 spin_unlock_irqrestore(&musb->lock, flags); 324 325 return ret; 326 } 327 328 static int da8xx_musb_set_mode(struct musb *musb, u8 musb_mode) 329 { 330 struct da8xx_glue *glue = dev_get_drvdata(musb->controller->parent); 331 enum phy_mode phy_mode; 332 333 /* 334 * The PHY has some issues when it is forced in device or host mode. 335 * Unless the user request another mode, configure the PHY in OTG mode. 336 */ 337 if (!musb->is_initialized) 338 return phy_set_mode(glue->phy, PHY_MODE_USB_OTG); 339 340 switch (musb_mode) { 341 case MUSB_HOST: /* Force VBUS valid, ID = 0 */ 342 phy_mode = PHY_MODE_USB_HOST; 343 break; 344 case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ 345 phy_mode = PHY_MODE_USB_DEVICE; 346 break; 347 case MUSB_OTG: /* Don't override the VBUS/ID comparators */ 348 phy_mode = PHY_MODE_USB_OTG; 349 break; 350 default: 351 return -EINVAL; 352 } 353 354 return phy_set_mode(glue->phy, phy_mode); 355 } 356 357 static int da8xx_musb_init(struct musb *musb) 358 { 359 struct da8xx_glue *glue = dev_get_drvdata(musb->controller->parent); 360 void __iomem *reg_base = musb->ctrl_base; 361 u32 rev; 362 int ret = -ENODEV; 363 364 musb->mregs += DA8XX_MENTOR_CORE_OFFSET; 365 366 ret = clk_prepare_enable(glue->clk); 367 if (ret) { 368 dev_err(glue->dev, "failed to enable clock\n"); 369 return ret; 370 } 371 372 /* Returns zero if e.g. not clocked */ 373 rev = musb_readl(reg_base, DA8XX_USB_REVISION_REG); 374 if (!rev) 375 goto fail; 376 377 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2); 378 if (IS_ERR_OR_NULL(musb->xceiv)) { 379 ret = -EPROBE_DEFER; 380 goto fail; 381 } 382 383 timer_setup(&musb->dev_timer, otg_timer, 0); 384 385 /* Reset the controller */ 386 musb_writel(reg_base, DA8XX_USB_CTRL_REG, DA8XX_SOFT_RESET_MASK); 387 388 /* Start the on-chip PHY and its PLL. */ 389 ret = phy_init(glue->phy); 390 if (ret) { 391 dev_err(glue->dev, "Failed to init phy.\n"); 392 goto fail; 393 } 394 395 ret = phy_power_on(glue->phy); 396 if (ret) { 397 dev_err(glue->dev, "Failed to power on phy.\n"); 398 goto err_phy_power_on; 399 } 400 401 msleep(5); 402 403 /* NOTE: IRQs are in mixed mode, not bypass to pure MUSB */ 404 pr_debug("DA8xx OTG revision %08x, control %02x\n", rev, 405 musb_readb(reg_base, DA8XX_USB_CTRL_REG)); 406 407 musb->isr = da8xx_musb_interrupt; 408 return 0; 409 410 err_phy_power_on: 411 phy_exit(glue->phy); 412 fail: 413 clk_disable_unprepare(glue->clk); 414 return ret; 415 } 416 417 static int da8xx_musb_exit(struct musb *musb) 418 { 419 struct da8xx_glue *glue = dev_get_drvdata(musb->controller->parent); 420 421 del_timer_sync(&musb->dev_timer); 422 423 phy_power_off(glue->phy); 424 phy_exit(glue->phy); 425 clk_disable_unprepare(glue->clk); 426 427 usb_put_phy(musb->xceiv); 428 429 return 0; 430 } 431 432 static inline u8 get_vbus_power(struct device *dev) 433 { 434 struct regulator *vbus_supply; 435 int current_uA; 436 437 vbus_supply = regulator_get_optional(dev, "vbus"); 438 if (IS_ERR(vbus_supply)) 439 return 255; 440 current_uA = regulator_get_current_limit(vbus_supply); 441 regulator_put(vbus_supply); 442 if (current_uA <= 0 || current_uA > 510000) 443 return 255; 444 return current_uA / 1000 / 2; 445 } 446 447 #ifdef CONFIG_USB_TI_CPPI41_DMA 448 static void da8xx_dma_controller_callback(struct dma_controller *c) 449 { 450 struct musb *musb = c->musb; 451 void __iomem *reg_base = musb->ctrl_base; 452 453 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 454 } 455 456 static struct dma_controller * 457 da8xx_dma_controller_create(struct musb *musb, void __iomem *base) 458 { 459 struct dma_controller *controller; 460 461 controller = cppi41_dma_controller_create(musb, base); 462 if (IS_ERR_OR_NULL(controller)) 463 return controller; 464 465 controller->dma_callback = da8xx_dma_controller_callback; 466 467 return controller; 468 } 469 #endif 470 471 static const struct musb_platform_ops da8xx_ops = { 472 .quirks = MUSB_INDEXED_EP | MUSB_PRESERVE_SESSION | 473 MUSB_DMA_CPPI41 | MUSB_DA8XX, 474 .init = da8xx_musb_init, 475 .exit = da8xx_musb_exit, 476 477 .fifo_mode = 2, 478 #ifdef CONFIG_USB_TI_CPPI41_DMA 479 .dma_init = da8xx_dma_controller_create, 480 .dma_exit = cppi41_dma_controller_destroy, 481 #endif 482 .enable = da8xx_musb_enable, 483 .disable = da8xx_musb_disable, 484 485 .set_mode = da8xx_musb_set_mode, 486 .try_idle = da8xx_musb_try_idle, 487 488 .set_vbus = da8xx_musb_set_vbus, 489 }; 490 491 static const struct platform_device_info da8xx_dev_info = { 492 .name = "musb-hdrc", 493 .id = PLATFORM_DEVID_AUTO, 494 .dma_mask = DMA_BIT_MASK(32), 495 }; 496 497 static const struct musb_hdrc_config da8xx_config = { 498 .ram_bits = 10, 499 .num_eps = 5, 500 .multipoint = 1, 501 }; 502 503 static struct of_dev_auxdata da8xx_auxdata_lookup[] = { 504 OF_DEV_AUXDATA("ti,da830-cppi41", 0x01e01000, "cppi41-dmaengine", 505 NULL), 506 {} 507 }; 508 509 static int da8xx_probe(struct platform_device *pdev) 510 { 511 struct resource musb_resources[2]; 512 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); 513 struct da8xx_glue *glue; 514 struct platform_device_info pinfo; 515 struct clk *clk; 516 struct device_node *np = pdev->dev.of_node; 517 int ret; 518 519 glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL); 520 if (!glue) 521 return -ENOMEM; 522 523 clk = devm_clk_get(&pdev->dev, NULL); 524 if (IS_ERR(clk)) { 525 dev_err(&pdev->dev, "failed to get clock\n"); 526 return PTR_ERR(clk); 527 } 528 529 glue->phy = devm_phy_get(&pdev->dev, "usb-phy"); 530 if (IS_ERR(glue->phy)) { 531 if (PTR_ERR(glue->phy) != -EPROBE_DEFER) 532 dev_err(&pdev->dev, "failed to get phy\n"); 533 return PTR_ERR(glue->phy); 534 } 535 536 glue->dev = &pdev->dev; 537 glue->clk = clk; 538 539 if (IS_ENABLED(CONFIG_OF) && np) { 540 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); 541 if (!pdata) 542 return -ENOMEM; 543 544 pdata->config = &da8xx_config; 545 pdata->mode = musb_get_mode(&pdev->dev); 546 pdata->power = get_vbus_power(&pdev->dev); 547 } 548 549 pdata->platform_ops = &da8xx_ops; 550 551 glue->usb_phy = usb_phy_generic_register(); 552 ret = PTR_ERR_OR_ZERO(glue->usb_phy); 553 if (ret) { 554 dev_err(&pdev->dev, "failed to register usb_phy\n"); 555 return ret; 556 } 557 platform_set_drvdata(pdev, glue); 558 559 ret = of_platform_populate(pdev->dev.of_node, NULL, 560 da8xx_auxdata_lookup, &pdev->dev); 561 if (ret) 562 return ret; 563 564 memset(musb_resources, 0x00, sizeof(*musb_resources) * 565 ARRAY_SIZE(musb_resources)); 566 567 musb_resources[0].name = pdev->resource[0].name; 568 musb_resources[0].start = pdev->resource[0].start; 569 musb_resources[0].end = pdev->resource[0].end; 570 musb_resources[0].flags = pdev->resource[0].flags; 571 572 musb_resources[1].name = pdev->resource[1].name; 573 musb_resources[1].start = pdev->resource[1].start; 574 musb_resources[1].end = pdev->resource[1].end; 575 musb_resources[1].flags = pdev->resource[1].flags; 576 577 pinfo = da8xx_dev_info; 578 pinfo.parent = &pdev->dev; 579 pinfo.res = musb_resources; 580 pinfo.num_res = ARRAY_SIZE(musb_resources); 581 pinfo.data = pdata; 582 pinfo.size_data = sizeof(*pdata); 583 584 glue->musb = platform_device_register_full(&pinfo); 585 ret = PTR_ERR_OR_ZERO(glue->musb); 586 if (ret) { 587 dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); 588 usb_phy_generic_unregister(glue->usb_phy); 589 } 590 591 return ret; 592 } 593 594 static int da8xx_remove(struct platform_device *pdev) 595 { 596 struct da8xx_glue *glue = platform_get_drvdata(pdev); 597 598 platform_device_unregister(glue->musb); 599 usb_phy_generic_unregister(glue->usb_phy); 600 601 return 0; 602 } 603 604 #ifdef CONFIG_PM_SLEEP 605 static int da8xx_suspend(struct device *dev) 606 { 607 int ret; 608 struct da8xx_glue *glue = dev_get_drvdata(dev); 609 610 ret = phy_power_off(glue->phy); 611 if (ret) 612 return ret; 613 clk_disable_unprepare(glue->clk); 614 615 return 0; 616 } 617 618 static int da8xx_resume(struct device *dev) 619 { 620 int ret; 621 struct da8xx_glue *glue = dev_get_drvdata(dev); 622 623 ret = clk_prepare_enable(glue->clk); 624 if (ret) 625 return ret; 626 return phy_power_on(glue->phy); 627 } 628 #endif 629 630 static SIMPLE_DEV_PM_OPS(da8xx_pm_ops, da8xx_suspend, da8xx_resume); 631 632 #ifdef CONFIG_OF 633 static const struct of_device_id da8xx_id_table[] = { 634 { 635 .compatible = "ti,da830-musb", 636 }, 637 {}, 638 }; 639 MODULE_DEVICE_TABLE(of, da8xx_id_table); 640 #endif 641 642 static struct platform_driver da8xx_driver = { 643 .probe = da8xx_probe, 644 .remove = da8xx_remove, 645 .driver = { 646 .name = "musb-da8xx", 647 .pm = &da8xx_pm_ops, 648 .of_match_table = of_match_ptr(da8xx_id_table), 649 }, 650 }; 651 652 MODULE_DESCRIPTION("DA8xx/OMAP-L1x MUSB Glue Layer"); 653 MODULE_AUTHOR("Sergei Shtylyov <sshtylyov@ru.mvista.com>"); 654 MODULE_LICENSE("GPL v2"); 655 module_platform_driver(da8xx_driver); 656