1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Texas Instruments DA8xx/OMAP-L1x "glue layer" 4 * 5 * Copyright (c) 2008-2009 MontaVista Software, Inc. <source@mvista.com> 6 * 7 * Based on the DaVinci "glue layer" code. 8 * Copyright (C) 2005-2006 by Texas Instruments 9 * 10 * DT support 11 * Copyright (c) 2016 Petr Kulhavy <petr@barix.com> 12 * 13 * This file is part of the Inventra Controller Driver for Linux. 14 */ 15 16 #include <linux/module.h> 17 #include <linux/clk.h> 18 #include <linux/err.h> 19 #include <linux/io.h> 20 #include <linux/of_platform.h> 21 #include <linux/phy/phy.h> 22 #include <linux/platform_device.h> 23 #include <linux/dma-mapping.h> 24 #include <linux/usb/usb_phy_generic.h> 25 26 #include "musb_core.h" 27 28 /* 29 * DA8XX specific definitions 30 */ 31 32 /* USB 2.0 OTG module registers */ 33 #define DA8XX_USB_REVISION_REG 0x00 34 #define DA8XX_USB_CTRL_REG 0x04 35 #define DA8XX_USB_STAT_REG 0x08 36 #define DA8XX_USB_EMULATION_REG 0x0c 37 #define DA8XX_USB_SRP_FIX_TIME_REG 0x18 38 #define DA8XX_USB_INTR_SRC_REG 0x20 39 #define DA8XX_USB_INTR_SRC_SET_REG 0x24 40 #define DA8XX_USB_INTR_SRC_CLEAR_REG 0x28 41 #define DA8XX_USB_INTR_MASK_REG 0x2c 42 #define DA8XX_USB_INTR_MASK_SET_REG 0x30 43 #define DA8XX_USB_INTR_MASK_CLEAR_REG 0x34 44 #define DA8XX_USB_INTR_SRC_MASKED_REG 0x38 45 #define DA8XX_USB_END_OF_INTR_REG 0x3c 46 #define DA8XX_USB_GENERIC_RNDIS_EP_SIZE_REG(n) (0x50 + (((n) - 1) << 2)) 47 48 /* Control register bits */ 49 #define DA8XX_SOFT_RESET_MASK 1 50 51 #define DA8XX_USB_TX_EP_MASK 0x1f /* EP0 + 4 Tx EPs */ 52 #define DA8XX_USB_RX_EP_MASK 0x1e /* 4 Rx EPs */ 53 54 /* USB interrupt register bits */ 55 #define DA8XX_INTR_USB_SHIFT 16 56 #define DA8XX_INTR_USB_MASK (0x1ff << DA8XX_INTR_USB_SHIFT) /* 8 Mentor */ 57 /* interrupts and DRVVBUS interrupt */ 58 #define DA8XX_INTR_DRVVBUS 0x100 59 #define DA8XX_INTR_RX_SHIFT 8 60 #define DA8XX_INTR_RX_MASK (DA8XX_USB_RX_EP_MASK << DA8XX_INTR_RX_SHIFT) 61 #define DA8XX_INTR_TX_SHIFT 0 62 #define DA8XX_INTR_TX_MASK (DA8XX_USB_TX_EP_MASK << DA8XX_INTR_TX_SHIFT) 63 64 #define DA8XX_MENTOR_CORE_OFFSET 0x400 65 66 struct da8xx_glue { 67 struct device *dev; 68 struct platform_device *musb; 69 struct platform_device *usb_phy; 70 struct clk *clk; 71 struct phy *phy; 72 }; 73 74 /* 75 * Because we don't set CTRL.UINT, it's "important" to: 76 * - not read/write INTRUSB/INTRUSBE (except during 77 * initial setup, as a workaround); 78 * - use INTSET/INTCLR instead. 79 */ 80 81 /** 82 * da8xx_musb_enable - enable interrupts 83 */ 84 static void da8xx_musb_enable(struct musb *musb) 85 { 86 void __iomem *reg_base = musb->ctrl_base; 87 u32 mask; 88 89 /* Workaround: setup IRQs through both register sets. */ 90 mask = ((musb->epmask & DA8XX_USB_TX_EP_MASK) << DA8XX_INTR_TX_SHIFT) | 91 ((musb->epmask & DA8XX_USB_RX_EP_MASK) << DA8XX_INTR_RX_SHIFT) | 92 DA8XX_INTR_USB_MASK; 93 musb_writel(reg_base, DA8XX_USB_INTR_MASK_SET_REG, mask); 94 95 /* Force the DRVVBUS IRQ so we can start polling for ID change. */ 96 musb_writel(reg_base, DA8XX_USB_INTR_SRC_SET_REG, 97 DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT); 98 } 99 100 /** 101 * da8xx_musb_disable - disable HDRC and flush interrupts 102 */ 103 static void da8xx_musb_disable(struct musb *musb) 104 { 105 void __iomem *reg_base = musb->ctrl_base; 106 107 musb_writel(reg_base, DA8XX_USB_INTR_MASK_CLEAR_REG, 108 DA8XX_INTR_USB_MASK | 109 DA8XX_INTR_TX_MASK | DA8XX_INTR_RX_MASK); 110 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 111 } 112 113 #define portstate(stmt) stmt 114 115 static void da8xx_musb_set_vbus(struct musb *musb, int is_on) 116 { 117 WARN_ON(is_on && is_peripheral_active(musb)); 118 } 119 120 #define POLL_SECONDS 2 121 122 static void otg_timer(struct timer_list *t) 123 { 124 struct musb *musb = from_timer(musb, t, dev_timer); 125 void __iomem *mregs = musb->mregs; 126 u8 devctl; 127 unsigned long flags; 128 129 /* 130 * We poll because DaVinci's won't expose several OTG-critical 131 * status change events (from the transceiver) otherwise. 132 */ 133 devctl = musb_readb(mregs, MUSB_DEVCTL); 134 dev_dbg(musb->controller, "Poll devctl %02x (%s)\n", devctl, 135 usb_otg_state_string(musb->xceiv->otg->state)); 136 137 spin_lock_irqsave(&musb->lock, flags); 138 switch (musb->xceiv->otg->state) { 139 case OTG_STATE_A_WAIT_BCON: 140 devctl &= ~MUSB_DEVCTL_SESSION; 141 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); 142 143 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 144 if (devctl & MUSB_DEVCTL_BDEVICE) { 145 musb->xceiv->otg->state = OTG_STATE_B_IDLE; 146 MUSB_DEV_MODE(musb); 147 } else { 148 musb->xceiv->otg->state = OTG_STATE_A_IDLE; 149 MUSB_HST_MODE(musb); 150 } 151 break; 152 case OTG_STATE_A_WAIT_VFALL: 153 /* 154 * Wait till VBUS falls below SessionEnd (~0.2 V); the 1.3 155 * RTL seems to mis-handle session "start" otherwise (or in 156 * our case "recover"), in routine "VBUS was valid by the time 157 * VBUSERR got reported during enumeration" cases. 158 */ 159 if (devctl & MUSB_DEVCTL_VBUS) { 160 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 161 break; 162 } 163 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE; 164 musb_writel(musb->ctrl_base, DA8XX_USB_INTR_SRC_SET_REG, 165 MUSB_INTR_VBUSERROR << DA8XX_INTR_USB_SHIFT); 166 break; 167 case OTG_STATE_B_IDLE: 168 /* 169 * There's no ID-changed IRQ, so we have no good way to tell 170 * when to switch to the A-Default state machine (by setting 171 * the DEVCTL.Session bit). 172 * 173 * Workaround: whenever we're in B_IDLE, try setting the 174 * session flag every few seconds. If it works, ID was 175 * grounded and we're now in the A-Default state machine. 176 * 177 * NOTE: setting the session flag is _supposed_ to trigger 178 * SRP but clearly it doesn't. 179 */ 180 musb_writeb(mregs, MUSB_DEVCTL, devctl | MUSB_DEVCTL_SESSION); 181 devctl = musb_readb(mregs, MUSB_DEVCTL); 182 if (devctl & MUSB_DEVCTL_BDEVICE) 183 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 184 else 185 musb->xceiv->otg->state = OTG_STATE_A_IDLE; 186 break; 187 default: 188 break; 189 } 190 spin_unlock_irqrestore(&musb->lock, flags); 191 } 192 193 static void da8xx_musb_try_idle(struct musb *musb, unsigned long timeout) 194 { 195 static unsigned long last_timer; 196 197 if (timeout == 0) 198 timeout = jiffies + msecs_to_jiffies(3); 199 200 /* Never idle if active, or when VBUS timeout is not set as host */ 201 if (musb->is_active || (musb->a_wait_bcon == 0 && 202 musb->xceiv->otg->state == OTG_STATE_A_WAIT_BCON)) { 203 dev_dbg(musb->controller, "%s active, deleting timer\n", 204 usb_otg_state_string(musb->xceiv->otg->state)); 205 del_timer(&musb->dev_timer); 206 last_timer = jiffies; 207 return; 208 } 209 210 if (time_after(last_timer, timeout) && timer_pending(&musb->dev_timer)) { 211 dev_dbg(musb->controller, "Longer idle timer already pending, ignoring...\n"); 212 return; 213 } 214 last_timer = timeout; 215 216 dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n", 217 usb_otg_state_string(musb->xceiv->otg->state), 218 jiffies_to_msecs(timeout - jiffies)); 219 mod_timer(&musb->dev_timer, timeout); 220 } 221 222 static irqreturn_t da8xx_musb_interrupt(int irq, void *hci) 223 { 224 struct musb *musb = hci; 225 void __iomem *reg_base = musb->ctrl_base; 226 unsigned long flags; 227 irqreturn_t ret = IRQ_NONE; 228 u32 status; 229 230 spin_lock_irqsave(&musb->lock, flags); 231 232 /* 233 * NOTE: DA8XX shadows the Mentor IRQs. Don't manage them through 234 * the Mentor registers (except for setup), use the TI ones and EOI. 235 */ 236 237 /* Acknowledge and handle non-CPPI interrupts */ 238 status = musb_readl(reg_base, DA8XX_USB_INTR_SRC_MASKED_REG); 239 if (!status) 240 goto eoi; 241 242 musb_writel(reg_base, DA8XX_USB_INTR_SRC_CLEAR_REG, status); 243 dev_dbg(musb->controller, "USB IRQ %08x\n", status); 244 245 musb->int_rx = (status & DA8XX_INTR_RX_MASK) >> DA8XX_INTR_RX_SHIFT; 246 musb->int_tx = (status & DA8XX_INTR_TX_MASK) >> DA8XX_INTR_TX_SHIFT; 247 musb->int_usb = (status & DA8XX_INTR_USB_MASK) >> DA8XX_INTR_USB_SHIFT; 248 249 /* 250 * DRVVBUS IRQs are the only proxy we have (a very poor one!) for 251 * DA8xx's missing ID change IRQ. We need an ID change IRQ to 252 * switch appropriately between halves of the OTG state machine. 253 * Managing DEVCTL.Session per Mentor docs requires that we know its 254 * value but DEVCTL.BDevice is invalid without DEVCTL.Session set. 255 * Also, DRVVBUS pulses for SRP (but not at 5 V)... 256 */ 257 if (status & (DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT)) { 258 int drvvbus = musb_readl(reg_base, DA8XX_USB_STAT_REG); 259 void __iomem *mregs = musb->mregs; 260 u8 devctl = musb_readb(mregs, MUSB_DEVCTL); 261 int err; 262 263 err = musb->int_usb & MUSB_INTR_VBUSERROR; 264 if (err) { 265 /* 266 * The Mentor core doesn't debounce VBUS as needed 267 * to cope with device connect current spikes. This 268 * means it's not uncommon for bus-powered devices 269 * to get VBUS errors during enumeration. 270 * 271 * This is a workaround, but newer RTL from Mentor 272 * seems to allow a better one: "re"-starting sessions 273 * without waiting for VBUS to stop registering in 274 * devctl. 275 */ 276 musb->int_usb &= ~MUSB_INTR_VBUSERROR; 277 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL; 278 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 279 WARNING("VBUS error workaround (delay coming)\n"); 280 } else if (drvvbus) { 281 MUSB_HST_MODE(musb); 282 musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE; 283 portstate(musb->port1_status |= USB_PORT_STAT_POWER); 284 del_timer(&musb->dev_timer); 285 } else if (!(musb->int_usb & MUSB_INTR_BABBLE)) { 286 /* 287 * When babble condition happens, drvvbus interrupt 288 * is also generated. Ignore this drvvbus interrupt 289 * and let babble interrupt handler recovers the 290 * controller; otherwise, the host-mode flag is lost 291 * due to the MUSB_DEV_MODE() call below and babble 292 * recovery logic will not be called. 293 */ 294 musb->is_active = 0; 295 MUSB_DEV_MODE(musb); 296 musb->xceiv->otg->state = OTG_STATE_B_IDLE; 297 portstate(musb->port1_status &= ~USB_PORT_STAT_POWER); 298 } 299 300 dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n", 301 drvvbus ? "on" : "off", 302 usb_otg_state_string(musb->xceiv->otg->state), 303 err ? " ERROR" : "", 304 devctl); 305 ret = IRQ_HANDLED; 306 } 307 308 if (musb->int_tx || musb->int_rx || musb->int_usb) 309 ret |= musb_interrupt(musb); 310 311 eoi: 312 /* EOI needs to be written for the IRQ to be re-asserted. */ 313 if (ret == IRQ_HANDLED || status) 314 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 315 316 /* Poll for ID change */ 317 if (musb->xceiv->otg->state == OTG_STATE_B_IDLE) 318 mod_timer(&musb->dev_timer, jiffies + POLL_SECONDS * HZ); 319 320 spin_unlock_irqrestore(&musb->lock, flags); 321 322 return ret; 323 } 324 325 static int da8xx_musb_set_mode(struct musb *musb, u8 musb_mode) 326 { 327 struct da8xx_glue *glue = dev_get_drvdata(musb->controller->parent); 328 enum phy_mode phy_mode; 329 330 /* 331 * The PHY has some issues when it is forced in device or host mode. 332 * Unless the user request another mode, configure the PHY in OTG mode. 333 */ 334 if (!musb->is_initialized) 335 return phy_set_mode(glue->phy, PHY_MODE_USB_OTG); 336 337 switch (musb_mode) { 338 case MUSB_HOST: /* Force VBUS valid, ID = 0 */ 339 phy_mode = PHY_MODE_USB_HOST; 340 break; 341 case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ 342 phy_mode = PHY_MODE_USB_DEVICE; 343 break; 344 case MUSB_OTG: /* Don't override the VBUS/ID comparators */ 345 phy_mode = PHY_MODE_USB_OTG; 346 break; 347 default: 348 return -EINVAL; 349 } 350 351 return phy_set_mode(glue->phy, phy_mode); 352 } 353 354 static int da8xx_musb_init(struct musb *musb) 355 { 356 struct da8xx_glue *glue = dev_get_drvdata(musb->controller->parent); 357 void __iomem *reg_base = musb->ctrl_base; 358 u32 rev; 359 int ret = -ENODEV; 360 361 musb->mregs += DA8XX_MENTOR_CORE_OFFSET; 362 363 ret = clk_prepare_enable(glue->clk); 364 if (ret) { 365 dev_err(glue->dev, "failed to enable clock\n"); 366 return ret; 367 } 368 369 /* Returns zero if e.g. not clocked */ 370 rev = musb_readl(reg_base, DA8XX_USB_REVISION_REG); 371 if (!rev) { 372 ret = -ENODEV; 373 goto fail; 374 } 375 376 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2); 377 if (IS_ERR_OR_NULL(musb->xceiv)) { 378 ret = -EPROBE_DEFER; 379 goto fail; 380 } 381 382 timer_setup(&musb->dev_timer, otg_timer, 0); 383 384 /* Reset the controller */ 385 musb_writel(reg_base, DA8XX_USB_CTRL_REG, DA8XX_SOFT_RESET_MASK); 386 387 /* Start the on-chip PHY and its PLL. */ 388 ret = phy_init(glue->phy); 389 if (ret) { 390 dev_err(glue->dev, "Failed to init phy.\n"); 391 goto fail; 392 } 393 394 ret = phy_power_on(glue->phy); 395 if (ret) { 396 dev_err(glue->dev, "Failed to power on phy.\n"); 397 goto err_phy_power_on; 398 } 399 400 msleep(5); 401 402 /* NOTE: IRQs are in mixed mode, not bypass to pure MUSB */ 403 pr_debug("DA8xx OTG revision %08x, control %02x\n", rev, 404 musb_readb(reg_base, DA8XX_USB_CTRL_REG)); 405 406 musb->isr = da8xx_musb_interrupt; 407 return 0; 408 409 err_phy_power_on: 410 phy_exit(glue->phy); 411 fail: 412 clk_disable_unprepare(glue->clk); 413 return ret; 414 } 415 416 static int da8xx_musb_exit(struct musb *musb) 417 { 418 struct da8xx_glue *glue = dev_get_drvdata(musb->controller->parent); 419 420 del_timer_sync(&musb->dev_timer); 421 422 phy_power_off(glue->phy); 423 phy_exit(glue->phy); 424 clk_disable_unprepare(glue->clk); 425 426 usb_put_phy(musb->xceiv); 427 428 return 0; 429 } 430 431 static inline u8 get_vbus_power(struct device *dev) 432 { 433 struct regulator *vbus_supply; 434 int current_uA; 435 436 vbus_supply = regulator_get_optional(dev, "vbus"); 437 if (IS_ERR(vbus_supply)) 438 return 255; 439 current_uA = regulator_get_current_limit(vbus_supply); 440 regulator_put(vbus_supply); 441 if (current_uA <= 0 || current_uA > 510000) 442 return 255; 443 return current_uA / 1000 / 2; 444 } 445 446 #ifdef CONFIG_USB_TI_CPPI41_DMA 447 static void da8xx_dma_controller_callback(struct dma_controller *c) 448 { 449 struct musb *musb = c->musb; 450 void __iomem *reg_base = musb->ctrl_base; 451 452 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 453 } 454 455 static struct dma_controller * 456 da8xx_dma_controller_create(struct musb *musb, void __iomem *base) 457 { 458 struct dma_controller *controller; 459 460 controller = cppi41_dma_controller_create(musb, base); 461 if (IS_ERR_OR_NULL(controller)) 462 return controller; 463 464 controller->dma_callback = da8xx_dma_controller_callback; 465 466 return controller; 467 } 468 #endif 469 470 static const struct musb_platform_ops da8xx_ops = { 471 .quirks = MUSB_INDEXED_EP | MUSB_PRESERVE_SESSION | 472 MUSB_DMA_CPPI41 | MUSB_DA8XX, 473 .init = da8xx_musb_init, 474 .exit = da8xx_musb_exit, 475 476 .fifo_mode = 2, 477 #ifdef CONFIG_USB_TI_CPPI41_DMA 478 .dma_init = da8xx_dma_controller_create, 479 .dma_exit = cppi41_dma_controller_destroy, 480 #endif 481 .enable = da8xx_musb_enable, 482 .disable = da8xx_musb_disable, 483 484 .set_mode = da8xx_musb_set_mode, 485 .try_idle = da8xx_musb_try_idle, 486 487 .set_vbus = da8xx_musb_set_vbus, 488 }; 489 490 static const struct platform_device_info da8xx_dev_info = { 491 .name = "musb-hdrc", 492 .id = PLATFORM_DEVID_AUTO, 493 .dma_mask = DMA_BIT_MASK(32), 494 }; 495 496 static const struct musb_hdrc_config da8xx_config = { 497 .ram_bits = 10, 498 .num_eps = 5, 499 .multipoint = 1, 500 }; 501 502 static struct of_dev_auxdata da8xx_auxdata_lookup[] = { 503 OF_DEV_AUXDATA("ti,da830-cppi41", 0x01e01000, "cppi41-dmaengine", 504 NULL), 505 {} 506 }; 507 508 static int da8xx_probe(struct platform_device *pdev) 509 { 510 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); 511 struct da8xx_glue *glue; 512 struct platform_device_info pinfo; 513 struct clk *clk; 514 struct device_node *np = pdev->dev.of_node; 515 int ret; 516 517 glue = devm_kzalloc(&pdev->dev, sizeof(*glue), GFP_KERNEL); 518 if (!glue) 519 return -ENOMEM; 520 521 clk = devm_clk_get(&pdev->dev, NULL); 522 if (IS_ERR(clk)) { 523 dev_err(&pdev->dev, "failed to get clock\n"); 524 return PTR_ERR(clk); 525 } 526 527 glue->phy = devm_phy_get(&pdev->dev, "usb-phy"); 528 if (IS_ERR(glue->phy)) 529 return dev_err_probe(&pdev->dev, PTR_ERR(glue->phy), 530 "failed to get phy\n"); 531 532 glue->dev = &pdev->dev; 533 glue->clk = clk; 534 535 if (IS_ENABLED(CONFIG_OF) && np) { 536 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); 537 if (!pdata) 538 return -ENOMEM; 539 540 pdata->config = &da8xx_config; 541 pdata->mode = musb_get_mode(&pdev->dev); 542 pdata->power = get_vbus_power(&pdev->dev); 543 } 544 545 pdata->platform_ops = &da8xx_ops; 546 547 glue->usb_phy = usb_phy_generic_register(); 548 ret = PTR_ERR_OR_ZERO(glue->usb_phy); 549 if (ret) { 550 dev_err(&pdev->dev, "failed to register usb_phy\n"); 551 return ret; 552 } 553 platform_set_drvdata(pdev, glue); 554 555 ret = of_platform_populate(pdev->dev.of_node, NULL, 556 da8xx_auxdata_lookup, &pdev->dev); 557 if (ret) 558 goto err_unregister_phy; 559 560 pinfo = da8xx_dev_info; 561 pinfo.parent = &pdev->dev; 562 pinfo.res = pdev->resource; 563 pinfo.num_res = pdev->num_resources; 564 pinfo.data = pdata; 565 pinfo.size_data = sizeof(*pdata); 566 pinfo.fwnode = of_fwnode_handle(np); 567 pinfo.of_node_reused = true; 568 569 glue->musb = platform_device_register_full(&pinfo); 570 ret = PTR_ERR_OR_ZERO(glue->musb); 571 if (ret) { 572 dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); 573 goto err_unregister_phy; 574 } 575 576 return 0; 577 578 err_unregister_phy: 579 usb_phy_generic_unregister(glue->usb_phy); 580 return ret; 581 } 582 583 static void da8xx_remove(struct platform_device *pdev) 584 { 585 struct da8xx_glue *glue = platform_get_drvdata(pdev); 586 587 platform_device_unregister(glue->musb); 588 usb_phy_generic_unregister(glue->usb_phy); 589 } 590 591 #ifdef CONFIG_PM_SLEEP 592 static int da8xx_suspend(struct device *dev) 593 { 594 int ret; 595 struct da8xx_glue *glue = dev_get_drvdata(dev); 596 597 ret = phy_power_off(glue->phy); 598 if (ret) 599 return ret; 600 clk_disable_unprepare(glue->clk); 601 602 return 0; 603 } 604 605 static int da8xx_resume(struct device *dev) 606 { 607 int ret; 608 struct da8xx_glue *glue = dev_get_drvdata(dev); 609 610 ret = clk_prepare_enable(glue->clk); 611 if (ret) 612 return ret; 613 return phy_power_on(glue->phy); 614 } 615 #endif 616 617 static SIMPLE_DEV_PM_OPS(da8xx_pm_ops, da8xx_suspend, da8xx_resume); 618 619 #ifdef CONFIG_OF 620 static const struct of_device_id da8xx_id_table[] = { 621 { 622 .compatible = "ti,da830-musb", 623 }, 624 {}, 625 }; 626 MODULE_DEVICE_TABLE(of, da8xx_id_table); 627 #endif 628 629 static struct platform_driver da8xx_driver = { 630 .probe = da8xx_probe, 631 .remove_new = da8xx_remove, 632 .driver = { 633 .name = "musb-da8xx", 634 .pm = &da8xx_pm_ops, 635 .of_match_table = of_match_ptr(da8xx_id_table), 636 }, 637 }; 638 639 MODULE_DESCRIPTION("DA8xx/OMAP-L1x MUSB Glue Layer"); 640 MODULE_AUTHOR("Sergei Shtylyov <sshtylyov@ru.mvista.com>"); 641 MODULE_LICENSE("GPL v2"); 642 module_platform_driver(da8xx_driver); 643