1 /* 2 * Texas Instruments DA8xx/OMAP-L1x "glue layer" 3 * 4 * Copyright (c) 2008-2009 MontaVista Software, Inc. <source@mvista.com> 5 * 6 * Based on the DaVinci "glue layer" code. 7 * Copyright (C) 2005-2006 by Texas Instruments 8 * 9 * This file is part of the Inventra Controller Driver for Linux. 10 * 11 * The Inventra Controller Driver for Linux is free software; you 12 * can redistribute it and/or modify it under the terms of the GNU 13 * General Public License version 2 as published by the Free Software 14 * Foundation. 15 * 16 * The Inventra Controller Driver for Linux is distributed in 17 * the hope that it will be useful, but WITHOUT ANY WARRANTY; 18 * without even the implied warranty of MERCHANTABILITY or 19 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public 20 * License for more details. 21 * 22 * You should have received a copy of the GNU General Public License 23 * along with The Inventra Controller Driver for Linux ; if not, 24 * write to the Free Software Foundation, Inc., 59 Temple Place, 25 * Suite 330, Boston, MA 02111-1307 USA 26 * 27 */ 28 29 #include <linux/module.h> 30 #include <linux/clk.h> 31 #include <linux/err.h> 32 #include <linux/io.h> 33 #include <linux/platform_device.h> 34 #include <linux/dma-mapping.h> 35 #include <linux/usb/usb_phy_generic.h> 36 37 #include <mach/da8xx.h> 38 #include <linux/platform_data/usb-davinci.h> 39 40 #include "musb_core.h" 41 42 /* 43 * DA8XX specific definitions 44 */ 45 46 /* USB 2.0 OTG module registers */ 47 #define DA8XX_USB_REVISION_REG 0x00 48 #define DA8XX_USB_CTRL_REG 0x04 49 #define DA8XX_USB_STAT_REG 0x08 50 #define DA8XX_USB_EMULATION_REG 0x0c 51 #define DA8XX_USB_MODE_REG 0x10 /* Transparent, CDC, [Generic] RNDIS */ 52 #define DA8XX_USB_AUTOREQ_REG 0x14 53 #define DA8XX_USB_SRP_FIX_TIME_REG 0x18 54 #define DA8XX_USB_TEARDOWN_REG 0x1c 55 #define DA8XX_USB_INTR_SRC_REG 0x20 56 #define DA8XX_USB_INTR_SRC_SET_REG 0x24 57 #define DA8XX_USB_INTR_SRC_CLEAR_REG 0x28 58 #define DA8XX_USB_INTR_MASK_REG 0x2c 59 #define DA8XX_USB_INTR_MASK_SET_REG 0x30 60 #define DA8XX_USB_INTR_MASK_CLEAR_REG 0x34 61 #define DA8XX_USB_INTR_SRC_MASKED_REG 0x38 62 #define DA8XX_USB_END_OF_INTR_REG 0x3c 63 #define DA8XX_USB_GENERIC_RNDIS_EP_SIZE_REG(n) (0x50 + (((n) - 1) << 2)) 64 65 /* Control register bits */ 66 #define DA8XX_SOFT_RESET_MASK 1 67 68 #define DA8XX_USB_TX_EP_MASK 0x1f /* EP0 + 4 Tx EPs */ 69 #define DA8XX_USB_RX_EP_MASK 0x1e /* 4 Rx EPs */ 70 71 /* USB interrupt register bits */ 72 #define DA8XX_INTR_USB_SHIFT 16 73 #define DA8XX_INTR_USB_MASK (0x1ff << DA8XX_INTR_USB_SHIFT) /* 8 Mentor */ 74 /* interrupts and DRVVBUS interrupt */ 75 #define DA8XX_INTR_DRVVBUS 0x100 76 #define DA8XX_INTR_RX_SHIFT 8 77 #define DA8XX_INTR_RX_MASK (DA8XX_USB_RX_EP_MASK << DA8XX_INTR_RX_SHIFT) 78 #define DA8XX_INTR_TX_SHIFT 0 79 #define DA8XX_INTR_TX_MASK (DA8XX_USB_TX_EP_MASK << DA8XX_INTR_TX_SHIFT) 80 81 #define DA8XX_MENTOR_CORE_OFFSET 0x400 82 83 #define CFGCHIP2 IO_ADDRESS(DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP2_REG) 84 85 struct da8xx_glue { 86 struct device *dev; 87 struct platform_device *musb; 88 struct platform_device *phy; 89 struct clk *clk; 90 }; 91 92 /* 93 * REVISIT (PM): we should be able to keep the PHY in low power mode most 94 * of the time (24 MHz oscillator and PLL off, etc.) by setting POWER.D0 95 * and, when in host mode, autosuspending idle root ports... PHY_PLLON 96 * (overriding SUSPENDM?) then likely needs to stay off. 97 */ 98 99 static inline void phy_on(void) 100 { 101 u32 cfgchip2 = __raw_readl(CFGCHIP2); 102 103 /* 104 * Start the on-chip PHY and its PLL. 105 */ 106 cfgchip2 &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN); 107 cfgchip2 |= CFGCHIP2_PHY_PLLON; 108 __raw_writel(cfgchip2, CFGCHIP2); 109 110 pr_info("Waiting for USB PHY clock good...\n"); 111 while (!(__raw_readl(CFGCHIP2) & CFGCHIP2_PHYCLKGD)) 112 cpu_relax(); 113 } 114 115 static inline void phy_off(void) 116 { 117 u32 cfgchip2 = __raw_readl(CFGCHIP2); 118 119 /* 120 * Ensure that USB 1.1 reference clock is not being sourced from 121 * USB 2.0 PHY. Otherwise do not power down the PHY. 122 */ 123 if (!(cfgchip2 & CFGCHIP2_USB1PHYCLKMUX) && 124 (cfgchip2 & CFGCHIP2_USB1SUSPENDM)) { 125 pr_warning("USB 1.1 clocked from USB 2.0 PHY -- " 126 "can't power it down\n"); 127 return; 128 } 129 130 /* 131 * Power down the on-chip PHY. 132 */ 133 cfgchip2 |= CFGCHIP2_PHYPWRDN | CFGCHIP2_OTGPWRDN; 134 __raw_writel(cfgchip2, CFGCHIP2); 135 } 136 137 /* 138 * Because we don't set CTRL.UINT, it's "important" to: 139 * - not read/write INTRUSB/INTRUSBE (except during 140 * initial setup, as a workaround); 141 * - use INTSET/INTCLR instead. 142 */ 143 144 /** 145 * da8xx_musb_enable - enable interrupts 146 */ 147 static void da8xx_musb_enable(struct musb *musb) 148 { 149 void __iomem *reg_base = musb->ctrl_base; 150 u32 mask; 151 152 /* Workaround: setup IRQs through both register sets. */ 153 mask = ((musb->epmask & DA8XX_USB_TX_EP_MASK) << DA8XX_INTR_TX_SHIFT) | 154 ((musb->epmask & DA8XX_USB_RX_EP_MASK) << DA8XX_INTR_RX_SHIFT) | 155 DA8XX_INTR_USB_MASK; 156 musb_writel(reg_base, DA8XX_USB_INTR_MASK_SET_REG, mask); 157 158 /* Force the DRVVBUS IRQ so we can start polling for ID change. */ 159 musb_writel(reg_base, DA8XX_USB_INTR_SRC_SET_REG, 160 DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT); 161 } 162 163 /** 164 * da8xx_musb_disable - disable HDRC and flush interrupts 165 */ 166 static void da8xx_musb_disable(struct musb *musb) 167 { 168 void __iomem *reg_base = musb->ctrl_base; 169 170 musb_writel(reg_base, DA8XX_USB_INTR_MASK_CLEAR_REG, 171 DA8XX_INTR_USB_MASK | 172 DA8XX_INTR_TX_MASK | DA8XX_INTR_RX_MASK); 173 musb_writeb(musb->mregs, MUSB_DEVCTL, 0); 174 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 175 } 176 177 #define portstate(stmt) stmt 178 179 static void da8xx_musb_set_vbus(struct musb *musb, int is_on) 180 { 181 WARN_ON(is_on && is_peripheral_active(musb)); 182 } 183 184 #define POLL_SECONDS 2 185 186 static struct timer_list otg_workaround; 187 188 static void otg_timer(unsigned long _musb) 189 { 190 struct musb *musb = (void *)_musb; 191 void __iomem *mregs = musb->mregs; 192 u8 devctl; 193 unsigned long flags; 194 195 /* 196 * We poll because DaVinci's won't expose several OTG-critical 197 * status change events (from the transceiver) otherwise. 198 */ 199 devctl = musb_readb(mregs, MUSB_DEVCTL); 200 dev_dbg(musb->controller, "Poll devctl %02x (%s)\n", devctl, 201 usb_otg_state_string(musb->xceiv->state)); 202 203 spin_lock_irqsave(&musb->lock, flags); 204 switch (musb->xceiv->state) { 205 case OTG_STATE_A_WAIT_BCON: 206 devctl &= ~MUSB_DEVCTL_SESSION; 207 musb_writeb(musb->mregs, MUSB_DEVCTL, devctl); 208 209 devctl = musb_readb(musb->mregs, MUSB_DEVCTL); 210 if (devctl & MUSB_DEVCTL_BDEVICE) { 211 musb->xceiv->state = OTG_STATE_B_IDLE; 212 MUSB_DEV_MODE(musb); 213 } else { 214 musb->xceiv->state = OTG_STATE_A_IDLE; 215 MUSB_HST_MODE(musb); 216 } 217 break; 218 case OTG_STATE_A_WAIT_VFALL: 219 /* 220 * Wait till VBUS falls below SessionEnd (~0.2 V); the 1.3 221 * RTL seems to mis-handle session "start" otherwise (or in 222 * our case "recover"), in routine "VBUS was valid by the time 223 * VBUSERR got reported during enumeration" cases. 224 */ 225 if (devctl & MUSB_DEVCTL_VBUS) { 226 mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); 227 break; 228 } 229 musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; 230 musb_writel(musb->ctrl_base, DA8XX_USB_INTR_SRC_SET_REG, 231 MUSB_INTR_VBUSERROR << DA8XX_INTR_USB_SHIFT); 232 break; 233 case OTG_STATE_B_IDLE: 234 /* 235 * There's no ID-changed IRQ, so we have no good way to tell 236 * when to switch to the A-Default state machine (by setting 237 * the DEVCTL.Session bit). 238 * 239 * Workaround: whenever we're in B_IDLE, try setting the 240 * session flag every few seconds. If it works, ID was 241 * grounded and we're now in the A-Default state machine. 242 * 243 * NOTE: setting the session flag is _supposed_ to trigger 244 * SRP but clearly it doesn't. 245 */ 246 musb_writeb(mregs, MUSB_DEVCTL, devctl | MUSB_DEVCTL_SESSION); 247 devctl = musb_readb(mregs, MUSB_DEVCTL); 248 if (devctl & MUSB_DEVCTL_BDEVICE) 249 mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); 250 else 251 musb->xceiv->state = OTG_STATE_A_IDLE; 252 break; 253 default: 254 break; 255 } 256 spin_unlock_irqrestore(&musb->lock, flags); 257 } 258 259 static void da8xx_musb_try_idle(struct musb *musb, unsigned long timeout) 260 { 261 static unsigned long last_timer; 262 263 if (timeout == 0) 264 timeout = jiffies + msecs_to_jiffies(3); 265 266 /* Never idle if active, or when VBUS timeout is not set as host */ 267 if (musb->is_active || (musb->a_wait_bcon == 0 && 268 musb->xceiv->state == OTG_STATE_A_WAIT_BCON)) { 269 dev_dbg(musb->controller, "%s active, deleting timer\n", 270 usb_otg_state_string(musb->xceiv->state)); 271 del_timer(&otg_workaround); 272 last_timer = jiffies; 273 return; 274 } 275 276 if (time_after(last_timer, timeout) && timer_pending(&otg_workaround)) { 277 dev_dbg(musb->controller, "Longer idle timer already pending, ignoring...\n"); 278 return; 279 } 280 last_timer = timeout; 281 282 dev_dbg(musb->controller, "%s inactive, starting idle timer for %u ms\n", 283 usb_otg_state_string(musb->xceiv->state), 284 jiffies_to_msecs(timeout - jiffies)); 285 mod_timer(&otg_workaround, timeout); 286 } 287 288 static irqreturn_t da8xx_musb_interrupt(int irq, void *hci) 289 { 290 struct musb *musb = hci; 291 void __iomem *reg_base = musb->ctrl_base; 292 struct usb_otg *otg = musb->xceiv->otg; 293 unsigned long flags; 294 irqreturn_t ret = IRQ_NONE; 295 u32 status; 296 297 spin_lock_irqsave(&musb->lock, flags); 298 299 /* 300 * NOTE: DA8XX shadows the Mentor IRQs. Don't manage them through 301 * the Mentor registers (except for setup), use the TI ones and EOI. 302 */ 303 304 /* Acknowledge and handle non-CPPI interrupts */ 305 status = musb_readl(reg_base, DA8XX_USB_INTR_SRC_MASKED_REG); 306 if (!status) 307 goto eoi; 308 309 musb_writel(reg_base, DA8XX_USB_INTR_SRC_CLEAR_REG, status); 310 dev_dbg(musb->controller, "USB IRQ %08x\n", status); 311 312 musb->int_rx = (status & DA8XX_INTR_RX_MASK) >> DA8XX_INTR_RX_SHIFT; 313 musb->int_tx = (status & DA8XX_INTR_TX_MASK) >> DA8XX_INTR_TX_SHIFT; 314 musb->int_usb = (status & DA8XX_INTR_USB_MASK) >> DA8XX_INTR_USB_SHIFT; 315 316 /* 317 * DRVVBUS IRQs are the only proxy we have (a very poor one!) for 318 * DA8xx's missing ID change IRQ. We need an ID change IRQ to 319 * switch appropriately between halves of the OTG state machine. 320 * Managing DEVCTL.Session per Mentor docs requires that we know its 321 * value but DEVCTL.BDevice is invalid without DEVCTL.Session set. 322 * Also, DRVVBUS pulses for SRP (but not at 5 V)... 323 */ 324 if (status & (DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT)) { 325 int drvvbus = musb_readl(reg_base, DA8XX_USB_STAT_REG); 326 void __iomem *mregs = musb->mregs; 327 u8 devctl = musb_readb(mregs, MUSB_DEVCTL); 328 int err; 329 330 err = musb->int_usb & MUSB_INTR_VBUSERROR; 331 if (err) { 332 /* 333 * The Mentor core doesn't debounce VBUS as needed 334 * to cope with device connect current spikes. This 335 * means it's not uncommon for bus-powered devices 336 * to get VBUS errors during enumeration. 337 * 338 * This is a workaround, but newer RTL from Mentor 339 * seems to allow a better one: "re"-starting sessions 340 * without waiting for VBUS to stop registering in 341 * devctl. 342 */ 343 musb->int_usb &= ~MUSB_INTR_VBUSERROR; 344 musb->xceiv->state = OTG_STATE_A_WAIT_VFALL; 345 mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); 346 WARNING("VBUS error workaround (delay coming)\n"); 347 } else if (drvvbus) { 348 MUSB_HST_MODE(musb); 349 otg->default_a = 1; 350 musb->xceiv->state = OTG_STATE_A_WAIT_VRISE; 351 portstate(musb->port1_status |= USB_PORT_STAT_POWER); 352 del_timer(&otg_workaround); 353 } else { 354 musb->is_active = 0; 355 MUSB_DEV_MODE(musb); 356 otg->default_a = 0; 357 musb->xceiv->state = OTG_STATE_B_IDLE; 358 portstate(musb->port1_status &= ~USB_PORT_STAT_POWER); 359 } 360 361 dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n", 362 drvvbus ? "on" : "off", 363 usb_otg_state_string(musb->xceiv->state), 364 err ? " ERROR" : "", 365 devctl); 366 ret = IRQ_HANDLED; 367 } 368 369 if (musb->int_tx || musb->int_rx || musb->int_usb) 370 ret |= musb_interrupt(musb); 371 372 eoi: 373 /* EOI needs to be written for the IRQ to be re-asserted. */ 374 if (ret == IRQ_HANDLED || status) 375 musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0); 376 377 /* Poll for ID change */ 378 if (musb->xceiv->state == OTG_STATE_B_IDLE) 379 mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ); 380 381 spin_unlock_irqrestore(&musb->lock, flags); 382 383 return ret; 384 } 385 386 static int da8xx_musb_set_mode(struct musb *musb, u8 musb_mode) 387 { 388 u32 cfgchip2 = __raw_readl(CFGCHIP2); 389 390 cfgchip2 &= ~CFGCHIP2_OTGMODE; 391 switch (musb_mode) { 392 case MUSB_HOST: /* Force VBUS valid, ID = 0 */ 393 cfgchip2 |= CFGCHIP2_FORCE_HOST; 394 break; 395 case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ 396 cfgchip2 |= CFGCHIP2_FORCE_DEVICE; 397 break; 398 case MUSB_OTG: /* Don't override the VBUS/ID comparators */ 399 cfgchip2 |= CFGCHIP2_NO_OVERRIDE; 400 break; 401 default: 402 dev_dbg(musb->controller, "Trying to set unsupported mode %u\n", musb_mode); 403 } 404 405 __raw_writel(cfgchip2, CFGCHIP2); 406 return 0; 407 } 408 409 static int da8xx_musb_init(struct musb *musb) 410 { 411 void __iomem *reg_base = musb->ctrl_base; 412 u32 rev; 413 int ret = -ENODEV; 414 415 musb->mregs += DA8XX_MENTOR_CORE_OFFSET; 416 417 /* Returns zero if e.g. not clocked */ 418 rev = musb_readl(reg_base, DA8XX_USB_REVISION_REG); 419 if (!rev) 420 goto fail; 421 422 musb->xceiv = usb_get_phy(USB_PHY_TYPE_USB2); 423 if (IS_ERR_OR_NULL(musb->xceiv)) { 424 ret = -EPROBE_DEFER; 425 goto fail; 426 } 427 428 setup_timer(&otg_workaround, otg_timer, (unsigned long)musb); 429 430 /* Reset the controller */ 431 musb_writel(reg_base, DA8XX_USB_CTRL_REG, DA8XX_SOFT_RESET_MASK); 432 433 /* Start the on-chip PHY and its PLL. */ 434 phy_on(); 435 436 msleep(5); 437 438 /* NOTE: IRQs are in mixed mode, not bypass to pure MUSB */ 439 pr_debug("DA8xx OTG revision %08x, PHY %03x, control %02x\n", 440 rev, __raw_readl(CFGCHIP2), 441 musb_readb(reg_base, DA8XX_USB_CTRL_REG)); 442 443 musb->isr = da8xx_musb_interrupt; 444 return 0; 445 fail: 446 return ret; 447 } 448 449 static int da8xx_musb_exit(struct musb *musb) 450 { 451 del_timer_sync(&otg_workaround); 452 453 phy_off(); 454 455 usb_put_phy(musb->xceiv); 456 457 return 0; 458 } 459 460 static const struct musb_platform_ops da8xx_ops = { 461 .init = da8xx_musb_init, 462 .exit = da8xx_musb_exit, 463 464 .enable = da8xx_musb_enable, 465 .disable = da8xx_musb_disable, 466 467 .set_mode = da8xx_musb_set_mode, 468 .try_idle = da8xx_musb_try_idle, 469 470 .set_vbus = da8xx_musb_set_vbus, 471 }; 472 473 static const struct platform_device_info da8xx_dev_info = { 474 .name = "musb-hdrc", 475 .id = PLATFORM_DEVID_AUTO, 476 .dma_mask = DMA_BIT_MASK(32), 477 }; 478 479 static int da8xx_probe(struct platform_device *pdev) 480 { 481 struct resource musb_resources[2]; 482 struct musb_hdrc_platform_data *pdata = dev_get_platdata(&pdev->dev); 483 struct platform_device *musb; 484 struct da8xx_glue *glue; 485 struct platform_device_info pinfo; 486 struct clk *clk; 487 488 int ret = -ENOMEM; 489 490 glue = kzalloc(sizeof(*glue), GFP_KERNEL); 491 if (!glue) { 492 dev_err(&pdev->dev, "failed to allocate glue context\n"); 493 goto err0; 494 } 495 496 clk = clk_get(&pdev->dev, "usb20"); 497 if (IS_ERR(clk)) { 498 dev_err(&pdev->dev, "failed to get clock\n"); 499 ret = PTR_ERR(clk); 500 goto err3; 501 } 502 503 ret = clk_enable(clk); 504 if (ret) { 505 dev_err(&pdev->dev, "failed to enable clock\n"); 506 goto err4; 507 } 508 509 glue->dev = &pdev->dev; 510 glue->clk = clk; 511 512 pdata->platform_ops = &da8xx_ops; 513 514 glue->phy = usb_phy_generic_register(); 515 if (IS_ERR(glue->phy)) { 516 ret = PTR_ERR(glue->phy); 517 goto err5; 518 } 519 platform_set_drvdata(pdev, glue); 520 521 memset(musb_resources, 0x00, sizeof(*musb_resources) * 522 ARRAY_SIZE(musb_resources)); 523 524 musb_resources[0].name = pdev->resource[0].name; 525 musb_resources[0].start = pdev->resource[0].start; 526 musb_resources[0].end = pdev->resource[0].end; 527 musb_resources[0].flags = pdev->resource[0].flags; 528 529 musb_resources[1].name = pdev->resource[1].name; 530 musb_resources[1].start = pdev->resource[1].start; 531 musb_resources[1].end = pdev->resource[1].end; 532 musb_resources[1].flags = pdev->resource[1].flags; 533 534 pinfo = da8xx_dev_info; 535 pinfo.parent = &pdev->dev; 536 pinfo.res = musb_resources; 537 pinfo.num_res = ARRAY_SIZE(musb_resources); 538 pinfo.data = pdata; 539 pinfo.size_data = sizeof(*pdata); 540 541 glue->musb = musb = platform_device_register_full(&pinfo); 542 if (IS_ERR(musb)) { 543 ret = PTR_ERR(musb); 544 dev_err(&pdev->dev, "failed to register musb device: %d\n", ret); 545 goto err6; 546 } 547 548 return 0; 549 550 err6: 551 usb_phy_generic_unregister(glue->phy); 552 553 err5: 554 clk_disable(clk); 555 556 err4: 557 clk_put(clk); 558 559 err3: 560 kfree(glue); 561 562 err0: 563 return ret; 564 } 565 566 static int da8xx_remove(struct platform_device *pdev) 567 { 568 struct da8xx_glue *glue = platform_get_drvdata(pdev); 569 570 platform_device_unregister(glue->musb); 571 usb_phy_generic_unregister(glue->phy); 572 clk_disable(glue->clk); 573 clk_put(glue->clk); 574 kfree(glue); 575 576 return 0; 577 } 578 579 static struct platform_driver da8xx_driver = { 580 .probe = da8xx_probe, 581 .remove = da8xx_remove, 582 .driver = { 583 .name = "musb-da8xx", 584 }, 585 }; 586 587 MODULE_DESCRIPTION("DA8xx/OMAP-L1x MUSB Glue Layer"); 588 MODULE_AUTHOR("Sergei Shtylyov <sshtylyov@ru.mvista.com>"); 589 MODULE_LICENSE("GPL v2"); 590 module_platform_driver(da8xx_driver); 591