1# SPDX-License-Identifier: GPL-2.0 2# 3# USB Miscellaneous driver configuration 4# 5comment "USB Miscellaneous drivers" 6 7config USB_USS720 8 tristate "USS720 parport driver" 9 depends on PARPORT 10 select PARPORT_NOT_PC 11 help 12 This driver is for USB parallel port adapters that use the Lucent 13 Technologies USS-720 chip. These cables are plugged into your USB 14 port and provide USB compatibility to peripherals designed with 15 parallel port interfaces. 16 17 The chip has two modes: automatic mode and manual mode. In automatic 18 mode, it looks to the computer like a standard USB printer. Only 19 printers may be connected to the USS-720 in this mode. The generic 20 USB printer driver ("USB Printer support", above) may be used in 21 that mode, and you can say N here if you want to use the chip only 22 in this mode. 23 24 Manual mode is not limited to printers, any parallel port 25 device should work. This driver utilizes manual mode. 26 Note however that some operations are three orders of magnitude 27 slower than on a PCI/ISA Parallel Port, so timing critical 28 applications might not work. 29 30 Say Y here if you own an USS-720 USB->Parport cable and intend to 31 connect anything other than a printer to it. 32 33 To compile this driver as a module, choose M here: the 34 module will be called uss720. 35 36config USB_EMI62 37 tristate "EMI 6|2m USB Audio interface support" 38 help 39 This driver loads firmware to Emagic EMI 6|2m low latency USB 40 Audio and Midi interface. 41 42 After firmware load the device is handled with standard linux 43 USB Audio driver. 44 45 This code is also available as a module ( = code which can be 46 inserted in and removed from the running kernel whenever you want). 47 The module will be called audio. If you want to compile it as a 48 module, say M here and read <file:Documentation/kbuild/modules.rst>. 49 50config USB_EMI26 51 tristate "EMI 2|6 USB Audio interface support" 52 help 53 This driver loads firmware to Emagic EMI 2|6 low latency USB 54 Audio interface. 55 56 After firmware load the device is handled with standard linux 57 USB Audio driver. 58 59 To compile this driver as a module, choose M here: the 60 module will be called emi26. 61 62config USB_ADUTUX 63 tristate "ADU devices from Ontrak Control Systems" 64 help 65 Say Y if you want to use an ADU device from Ontrak Control 66 Systems. 67 68 To compile this driver as a module, choose M here. The module 69 will be called adutux. 70 71config USB_SEVSEG 72 tristate "USB 7-Segment LED Display" 73 help 74 Say Y here if you have a USB 7-Segment Display by Delcom 75 76 To compile this driver as a module, choose M here: the 77 module will be called usbsevseg. 78 79config USB_LEGOTOWER 80 tristate "USB Lego Infrared Tower support" 81 help 82 Say Y here if you want to connect a USB Lego Infrared Tower to your 83 computer's USB port. 84 85 This code is also available as a module ( = code which can be 86 inserted in and removed from the running kernel whenever you want). 87 The module will be called legousbtower. If you want to compile it as 88 a module, say M here and read 89 <file:Documentation/kbuild/modules.rst>. 90 91config USB_LCD 92 tristate "USB LCD driver support" 93 help 94 Say Y here if you want to connect an USBLCD to your computer's 95 USB port. The USBLCD is a small USB interface board for 96 alphanumeric LCD modules. See <http://www.usblcd.de/> for more 97 information. 98 99 To compile this driver as a module, choose M here: the 100 module will be called usblcd. 101 102config USB_CYPRESS_CY7C63 103 tristate "Cypress CY7C63xxx USB driver support" 104 help 105 Say Y here if you want to connect a Cypress CY7C63xxx 106 micro controller to your computer's USB port. Currently this 107 driver supports the pre-programmed devices (incl. firmware) 108 by AK Modul-Bus Computer GmbH. 109 110 Please see: https://www.ak-modul-bus.de/stat/mikrocontroller.html 111 112 To compile this driver as a module, choose M here: the 113 module will be called cypress_cy7c63. 114 115config USB_CYTHERM 116 tristate "Cypress USB thermometer driver support" 117 help 118 Say Y here if you want to connect a Cypress USB thermometer 119 device to your computer's USB port. This device is also known 120 as the Cypress USB Starter kit or demo board. The Elektor 121 magazine published a modified version of this device in issue 122 #291. 123 124 To compile this driver as a module, choose M here: the 125 module will be called cytherm. 126 127config USB_IDMOUSE 128 tristate "Siemens ID USB Mouse Fingerprint sensor support" 129 help 130 Say Y here if you want to use the fingerprint sensor on 131 the Siemens ID Mouse. There is also a Siemens ID Mouse 132 _Professional_, which has not been tested with this driver, 133 but uses the same sensor and may therefore work. 134 135 This driver creates an entry "/dev/idmouseX" or "/dev/usb/idmouseX", 136 which can be used by, e.g.,"cat /dev/idmouse0 > fingerprint.pnm". 137 138 See also <https://www.fs.tum.de/~echtler/idmouse/>. 139 140config USB_APPLEDISPLAY 141 tristate "Apple Cinema Display support" 142 select BACKLIGHT_CLASS_DEVICE 143 help 144 Say Y here if you want to control the backlight of Apple Cinema 145 Displays over USB. This driver provides a sysfs interface. 146 147config USB_QCOM_EUD 148 tristate "QCOM Embedded USB Debugger(EUD) Driver" 149 depends on ARCH_QCOM || COMPILE_TEST 150 select USB_ROLE_SWITCH 151 help 152 This module enables support for Qualcomm Technologies, Inc. 153 Embedded USB Debugger (EUD). The EUD is a control peripheral 154 which reports VBUS attach/detach events and has USB-based 155 debug and trace capabilities. On selecting m, the module name 156 that is built is qcom_eud.ko 157 158config APPLE_MFI_FASTCHARGE 159 tristate "Fast charge control for iOS devices" 160 select POWER_SUPPLY 161 help 162 Say Y here if you want to control whether iOS devices will 163 fast charge from the USB interface, as implemented in "MFi" 164 chargers. 165 166 It is safe to say M here. 167 168source "drivers/usb/misc/sisusbvga/Kconfig" 169 170config USB_LD 171 tristate "USB LD driver" 172 help 173 This driver is for generic USB devices that use interrupt transfers, 174 like LD Didactic's USB devices. 175 176 To compile this driver as a module, choose M here: the 177 module will be called ldusb. 178 179config USB_TRANCEVIBRATOR 180 tristate "PlayStation 2 Trance Vibrator driver support" 181 help 182 Say Y here if you want to connect a PlayStation 2 Trance Vibrator 183 device to your computer's USB port. 184 185 To compile this driver as a module, choose M here: the 186 module will be called trancevibrator. 187 188config USB_IOWARRIOR 189 tristate "IO Warrior driver support" 190 help 191 Say Y here if you want to support the IO Warrior devices from Code 192 Mercenaries. This includes support for the following devices: 193 IO Warrior 40 194 IO Warrior 24 195 IO Warrior 56 196 IO Warrior 24 Power Vampire 197 198 To compile this driver as a module, choose M here: the 199 module will be called iowarrior. 200 201config USB_TEST 202 tristate "USB testing driver" 203 help 204 This driver is for testing host controller software. It is used 205 with specialized device firmware for regression and stress testing, 206 to help prevent problems from cropping up with "real" drivers. 207 208 See <http://www.linux-usb.org/usbtest/> for more information, 209 including sample test device firmware and "how to use it". 210 211config USB_EHSET_TEST_FIXTURE 212 tristate "USB EHSET Test Fixture driver" 213 help 214 Say Y here if you want to support the special test fixture device 215 used for the USB-IF Embedded Host High-Speed Electrical Test procedure. 216 217 When the test fixture is connected, it can enumerate as one of several 218 VID/PID pairs. This driver then initiates a corresponding test mode on 219 the downstream port to which the test fixture is attached. 220 221 See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more 222 information. 223 224config USB_ISIGHTFW 225 tristate "iSight firmware loading support" 226 select FW_LOADER 227 help 228 This driver loads firmware for USB Apple iSight cameras, allowing 229 them to be driven by the USB video class driver available at 230 http://linux-uvc.berlios.de 231 232 The firmware for this driver must be extracted from the MacOS 233 driver beforehand. Tools for doing so are available at 234 http://bersace03.free.fr 235 236config USB_YUREX 237 tristate "USB YUREX driver support" 238 help 239 Say Y here if you want to connect a YUREX to your computer's 240 USB port. The YUREX is a leg-shakes sensor. See 241 <http://bbu.kayac.com/en/> for further information. 242 This driver supports read/write of leg-shakes counter and 243 fasync for the counter update via a device file /dev/yurex*. 244 245 To compile this driver as a module, choose M here: the 246 module will be called yurex. 247 248config USB_EZUSB_FX2 249 tristate "Functions for loading firmware on EZUSB chips" 250 help 251 Say Y here if you need EZUSB device support. 252 (Cypress FX/FX2/FX2LP microcontrollers) 253 254config USB_HUB_USB251XB 255 tristate "USB251XB Hub Controller Configuration Driver" 256 depends on I2C 257 help 258 This option enables support for configuration via SMBus of the 259 Microchip USB251x/xBi USB 2.0 Hub Controller series. Configuration 260 parameters may be set in devicetree or platform data. 261 Say Y or M here if you need to configure such a device via SMBus. 262 263config USB_HSIC_USB3503 264 tristate "USB3503 HSIC to USB20 Driver" 265 depends on I2C 266 select REGMAP_I2C 267 help 268 This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver. 269 270config USB_HSIC_USB4604 271 tristate "USB4604 HSIC to USB20 Driver" 272 depends on I2C 273 help 274 This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver. 275 276config USB_LINK_LAYER_TEST 277 tristate "USB Link Layer Test driver" 278 help 279 This driver is for generating specific traffic for Super Speed Link 280 Layer Test Device. Say Y only when you want to conduct USB Super Speed 281 Link Layer Test for host controllers. 282 283config USB_CHAOSKEY 284 tristate "ChaosKey random number generator driver support" 285 depends on HW_RANDOM 286 help 287 Say Y here if you want to connect an AltusMetrum ChaosKey or 288 Araneus Alea I to your computer's USB port. These devices 289 are hardware random number generators which hook into the 290 kernel entropy pool to ensure a large supply of entropy for 291 /dev/random and /dev/urandom and also provides direct access 292 via /dev/chaoskeyX 293 294 To compile this driver as a module, choose M here: the 295 module will be called chaoskey. 296 297config BRCM_USB_PINMAP 298 tristate "Broadcom pinmap driver support" 299 depends on (ARCH_BRCMSTB && PHY_BRCM_USB) || COMPILE_TEST 300 default ARCH_BRCMSTB && PHY_BRCM_USB 301 help 302 This option enables support for remapping some USB external 303 signals, which are typically on dedicated pins on the chip, 304 to any gpio. 305 306config USB_ONBOARD_HUB 307 tristate "Onboard USB hub support" 308 depends on OF 309 help 310 Say Y here if you want to support discrete onboard USB hubs that 311 don't require an additional control bus for initialization, but 312 need some non-trivial form of initialization, such as enabling a 313 power regulator. An example for such a hub is the Realtek 314 RTS5411. 315 316 This driver can be used as a module but its state (module vs 317 builtin) must match the state of the USB subsystem. Enabling 318 this config will enable the driver and it will automatically 319 match the state of the USB subsystem. If this driver is a 320 module it will be called onboard_usb_hub. 321