1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * xHCI host controller driver for R-Car SoCs 4 * 5 * Copyright (C) 2014 Renesas Electronics Corporation 6 */ 7 8 #include <linux/firmware.h> 9 #include <linux/iopoll.h> 10 #include <linux/module.h> 11 #include <linux/platform_device.h> 12 #include <linux/of.h> 13 #include <linux/usb/phy.h> 14 #include <linux/sys_soc.h> 15 16 #include "xhci.h" 17 #include "xhci-plat.h" 18 #include "xhci-rcar.h" 19 20 /* 21 * - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x) 22 * - The V2 firmware is for r8a7795 ES1.x. 23 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes 24 * performance degradation. So, this driver continues to use the V1 if R-Car 25 * Gen2. 26 * - The V1 firmware is impossible to use on R-Car Gen3. 27 */ 28 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1); 29 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2); 30 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3); 31 32 /*** Register Offset ***/ 33 #define RCAR_USB3_AXH_STA 0x104 /* AXI Host Control Status */ 34 #define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */ 35 #define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */ 36 #define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */ 37 38 #define RCAR_USB3_LCLK 0xa44 /* LCLK Select */ 39 #define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */ 40 #define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */ 41 #define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */ 42 #define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */ 43 #define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */ 44 45 /*** Register Settings ***/ 46 /* AXI Host Control Status */ 47 #define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE 0x00010000 48 #define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE 0x00000001 49 #define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \ 50 RCAR_USB3_AXH_STA_B2_PLL_ACTIVE) 51 52 /* Interrupt Enable */ 53 #define RCAR_USB3_INT_XHC_ENA 0x00000001 54 #define RCAR_USB3_INT_PME_ENA 0x00000002 55 #define RCAR_USB3_INT_HSE_ENA 0x00000004 56 #define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \ 57 RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA) 58 59 /* FW Download Control & Status */ 60 #define RCAR_USB3_DL_CTRL_ENABLE 0x00000001 61 #define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010 62 #define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100 63 64 /* LCLK Select */ 65 #define RCAR_USB3_LCLK_ENA_VAL 0x01030001 66 67 /* USB3.0 Configuration */ 68 #define RCAR_USB3_CONF1_VAL 0x00030204 69 #define RCAR_USB3_CONF2_VAL 0x00030300 70 #define RCAR_USB3_CONF3_VAL 0x13802007 71 72 /* USB3.0 Polarity */ 73 #define RCAR_USB3_RX_POL_VAL BIT(21) 74 #define RCAR_USB3_TX_POL_VAL BIT(4) 75 76 /* For soc_device_attribute */ 77 #define RCAR_XHCI_FIRMWARE_V2 BIT(0) /* FIRMWARE V2 */ 78 #define RCAR_XHCI_FIRMWARE_V3 BIT(1) /* FIRMWARE V3 */ 79 80 static const struct soc_device_attribute rcar_quirks_match[] = { 81 { 82 .soc_id = "r8a7795", .revision = "ES1.*", 83 .data = (void *)RCAR_XHCI_FIRMWARE_V2, 84 }, 85 { /* sentinel */ }, 86 }; 87 88 static void xhci_rcar_start_gen2(struct usb_hcd *hcd) 89 { 90 /* LCLK Select */ 91 writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK); 92 /* USB3.0 Configuration */ 93 writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1); 94 writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2); 95 writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3); 96 /* USB3.0 Polarity */ 97 writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL); 98 writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL); 99 } 100 101 static int xhci_rcar_is_gen2(struct device *dev) 102 { 103 struct device_node *node = dev->of_node; 104 105 return of_device_is_compatible(node, "renesas,xhci-r8a7790") || 106 of_device_is_compatible(node, "renesas,xhci-r8a7791") || 107 of_device_is_compatible(node, "renesas,xhci-r8a7793") || 108 of_device_is_compatible(node, "renesas,rcar-gen2-xhci"); 109 } 110 111 void xhci_rcar_start(struct usb_hcd *hcd) 112 { 113 u32 temp; 114 115 if (hcd->regs != NULL) { 116 /* Interrupt Enable */ 117 temp = readl(hcd->regs + RCAR_USB3_INT_ENA); 118 temp |= RCAR_USB3_INT_ENA_VAL; 119 writel(temp, hcd->regs + RCAR_USB3_INT_ENA); 120 if (xhci_rcar_is_gen2(hcd->self.controller)) 121 xhci_rcar_start_gen2(hcd); 122 } 123 } 124 125 static int xhci_rcar_download_firmware(struct usb_hcd *hcd) 126 { 127 struct device *dev = hcd->self.controller; 128 void __iomem *regs = hcd->regs; 129 struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd); 130 const struct firmware *fw; 131 int retval, index, j; 132 u32 data, val, temp; 133 u32 quirks = 0; 134 const struct soc_device_attribute *attr; 135 const char *firmware_name; 136 137 attr = soc_device_match(rcar_quirks_match); 138 if (attr) 139 quirks = (uintptr_t)attr->data; 140 141 if (quirks & RCAR_XHCI_FIRMWARE_V2) 142 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2; 143 else if (quirks & RCAR_XHCI_FIRMWARE_V3) 144 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3; 145 else 146 firmware_name = priv->firmware_name; 147 148 /* request R-Car USB3.0 firmware */ 149 retval = request_firmware(&fw, firmware_name, dev); 150 if (retval) 151 return retval; 152 153 /* download R-Car USB3.0 firmware */ 154 temp = readl(regs + RCAR_USB3_DL_CTRL); 155 temp |= RCAR_USB3_DL_CTRL_ENABLE; 156 writel(temp, regs + RCAR_USB3_DL_CTRL); 157 158 for (index = 0; index < fw->size; index += 4) { 159 /* to avoid reading beyond the end of the buffer */ 160 for (data = 0, j = 3; j >= 0; j--) { 161 if ((j + index) < fw->size) 162 data |= fw->data[index + j] << (8 * j); 163 } 164 writel(data, regs + RCAR_USB3_FW_DATA0); 165 temp = readl(regs + RCAR_USB3_DL_CTRL); 166 temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0; 167 writel(temp, regs + RCAR_USB3_DL_CTRL); 168 169 retval = readl_poll_timeout_atomic(regs + RCAR_USB3_DL_CTRL, 170 val, !(val & RCAR_USB3_DL_CTRL_FW_SET_DATA0), 171 1, 10000); 172 if (retval < 0) 173 break; 174 } 175 176 temp = readl(regs + RCAR_USB3_DL_CTRL); 177 temp &= ~RCAR_USB3_DL_CTRL_ENABLE; 178 writel(temp, regs + RCAR_USB3_DL_CTRL); 179 180 retval = readl_poll_timeout_atomic((regs + RCAR_USB3_DL_CTRL), 181 val, val & RCAR_USB3_DL_CTRL_FW_SUCCESS, 1, 10000); 182 183 release_firmware(fw); 184 185 return retval; 186 } 187 188 static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd) 189 { 190 int retval; 191 u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK; 192 193 retval = readl_poll_timeout_atomic(hcd->regs + RCAR_USB3_AXH_STA, 194 val, (val & mask) == mask, 1, 1000); 195 return !retval; 196 } 197 198 /* This function needs to initialize a "phy" of usb before */ 199 int xhci_rcar_init_quirk(struct usb_hcd *hcd) 200 { 201 /* If hcd->regs is NULL, we don't just call the following function */ 202 if (!hcd->regs) 203 return 0; 204 205 if (!xhci_rcar_wait_for_pll_active(hcd)) 206 return -ETIMEDOUT; 207 208 return xhci_rcar_download_firmware(hcd); 209 } 210 211 int xhci_rcar_resume_quirk(struct usb_hcd *hcd) 212 { 213 int ret; 214 215 ret = xhci_rcar_download_firmware(hcd); 216 if (!ret) 217 xhci_rcar_start(hcd); 218 219 return ret; 220 } 221