1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * xHCI host controller driver for R-Car SoCs 4 * 5 * Copyright (C) 2014 Renesas Electronics Corporation 6 */ 7 8 #include <linux/firmware.h> 9 #include <linux/module.h> 10 #include <linux/platform_device.h> 11 #include <linux/of.h> 12 #include <linux/usb/phy.h> 13 #include <linux/sys_soc.h> 14 15 #include "xhci.h" 16 #include "xhci-plat.h" 17 #include "xhci-rcar.h" 18 19 /* 20 * - The V3 firmware is for almost all R-Car Gen3 (except r8a7795 ES1.x) 21 * - The V2 firmware is for r8a7795 ES1.x. 22 * - The V2 firmware is possible to use on R-Car Gen2. However, the V2 causes 23 * performance degradation. So, this driver continues to use the V1 if R-Car 24 * Gen2. 25 * - The V1 firmware is impossible to use on R-Car Gen3. 26 */ 27 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V1); 28 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V2); 29 MODULE_FIRMWARE(XHCI_RCAR_FIRMWARE_NAME_V3); 30 31 /*** Register Offset ***/ 32 #define RCAR_USB3_AXH_STA 0x104 /* AXI Host Control Status */ 33 #define RCAR_USB3_INT_ENA 0x224 /* Interrupt Enable */ 34 #define RCAR_USB3_DL_CTRL 0x250 /* FW Download Control & Status */ 35 #define RCAR_USB3_FW_DATA0 0x258 /* FW Data0 */ 36 37 #define RCAR_USB3_LCLK 0xa44 /* LCLK Select */ 38 #define RCAR_USB3_CONF1 0xa48 /* USB3.0 Configuration1 */ 39 #define RCAR_USB3_CONF2 0xa5c /* USB3.0 Configuration2 */ 40 #define RCAR_USB3_CONF3 0xaa8 /* USB3.0 Configuration3 */ 41 #define RCAR_USB3_RX_POL 0xab0 /* USB3.0 RX Polarity */ 42 #define RCAR_USB3_TX_POL 0xab8 /* USB3.0 TX Polarity */ 43 44 /*** Register Settings ***/ 45 /* AXI Host Control Status */ 46 #define RCAR_USB3_AXH_STA_B3_PLL_ACTIVE 0x00010000 47 #define RCAR_USB3_AXH_STA_B2_PLL_ACTIVE 0x00000001 48 #define RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK (RCAR_USB3_AXH_STA_B3_PLL_ACTIVE | \ 49 RCAR_USB3_AXH_STA_B2_PLL_ACTIVE) 50 51 /* Interrupt Enable */ 52 #define RCAR_USB3_INT_XHC_ENA 0x00000001 53 #define RCAR_USB3_INT_PME_ENA 0x00000002 54 #define RCAR_USB3_INT_HSE_ENA 0x00000004 55 #define RCAR_USB3_INT_ENA_VAL (RCAR_USB3_INT_XHC_ENA | \ 56 RCAR_USB3_INT_PME_ENA | RCAR_USB3_INT_HSE_ENA) 57 58 /* FW Download Control & Status */ 59 #define RCAR_USB3_DL_CTRL_ENABLE 0x00000001 60 #define RCAR_USB3_DL_CTRL_FW_SUCCESS 0x00000010 61 #define RCAR_USB3_DL_CTRL_FW_SET_DATA0 0x00000100 62 63 /* LCLK Select */ 64 #define RCAR_USB3_LCLK_ENA_VAL 0x01030001 65 66 /* USB3.0 Configuration */ 67 #define RCAR_USB3_CONF1_VAL 0x00030204 68 #define RCAR_USB3_CONF2_VAL 0x00030300 69 #define RCAR_USB3_CONF3_VAL 0x13802007 70 71 /* USB3.0 Polarity */ 72 #define RCAR_USB3_RX_POL_VAL BIT(21) 73 #define RCAR_USB3_TX_POL_VAL BIT(4) 74 75 /* For soc_device_attribute */ 76 #define RCAR_XHCI_FIRMWARE_V2 BIT(0) /* FIRMWARE V2 */ 77 #define RCAR_XHCI_FIRMWARE_V3 BIT(1) /* FIRMWARE V3 */ 78 79 static const struct soc_device_attribute rcar_quirks_match[] = { 80 { 81 .soc_id = "r8a7795", .revision = "ES1.*", 82 .data = (void *)RCAR_XHCI_FIRMWARE_V2, 83 }, 84 { /* sentinel */ }, 85 }; 86 87 static void xhci_rcar_start_gen2(struct usb_hcd *hcd) 88 { 89 /* LCLK Select */ 90 writel(RCAR_USB3_LCLK_ENA_VAL, hcd->regs + RCAR_USB3_LCLK); 91 /* USB3.0 Configuration */ 92 writel(RCAR_USB3_CONF1_VAL, hcd->regs + RCAR_USB3_CONF1); 93 writel(RCAR_USB3_CONF2_VAL, hcd->regs + RCAR_USB3_CONF2); 94 writel(RCAR_USB3_CONF3_VAL, hcd->regs + RCAR_USB3_CONF3); 95 /* USB3.0 Polarity */ 96 writel(RCAR_USB3_RX_POL_VAL, hcd->regs + RCAR_USB3_RX_POL); 97 writel(RCAR_USB3_TX_POL_VAL, hcd->regs + RCAR_USB3_TX_POL); 98 } 99 100 static int xhci_rcar_is_gen2(struct device *dev) 101 { 102 struct device_node *node = dev->of_node; 103 104 return of_device_is_compatible(node, "renesas,xhci-r8a7790") || 105 of_device_is_compatible(node, "renesas,xhci-r8a7791") || 106 of_device_is_compatible(node, "renesas,xhci-r8a7793") || 107 of_device_is_compatible(node, "renesas,rcar-gen2-xhci"); 108 } 109 110 void xhci_rcar_start(struct usb_hcd *hcd) 111 { 112 u32 temp; 113 114 if (hcd->regs != NULL) { 115 /* Interrupt Enable */ 116 temp = readl(hcd->regs + RCAR_USB3_INT_ENA); 117 temp |= RCAR_USB3_INT_ENA_VAL; 118 writel(temp, hcd->regs + RCAR_USB3_INT_ENA); 119 if (xhci_rcar_is_gen2(hcd->self.controller)) 120 xhci_rcar_start_gen2(hcd); 121 } 122 } 123 124 static int xhci_rcar_download_firmware(struct usb_hcd *hcd) 125 { 126 struct device *dev = hcd->self.controller; 127 void __iomem *regs = hcd->regs; 128 struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd); 129 const struct firmware *fw; 130 int retval, index, j, time; 131 int timeout = 10000; 132 u32 data, val, temp; 133 u32 quirks = 0; 134 const struct soc_device_attribute *attr; 135 const char *firmware_name; 136 137 attr = soc_device_match(rcar_quirks_match); 138 if (attr) 139 quirks = (uintptr_t)attr->data; 140 141 if (quirks & RCAR_XHCI_FIRMWARE_V2) 142 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V2; 143 else if (quirks & RCAR_XHCI_FIRMWARE_V3) 144 firmware_name = XHCI_RCAR_FIRMWARE_NAME_V3; 145 else 146 firmware_name = priv->firmware_name; 147 148 /* request R-Car USB3.0 firmware */ 149 retval = request_firmware(&fw, firmware_name, dev); 150 if (retval) 151 return retval; 152 153 /* download R-Car USB3.0 firmware */ 154 temp = readl(regs + RCAR_USB3_DL_CTRL); 155 temp |= RCAR_USB3_DL_CTRL_ENABLE; 156 writel(temp, regs + RCAR_USB3_DL_CTRL); 157 158 for (index = 0; index < fw->size; index += 4) { 159 /* to avoid reading beyond the end of the buffer */ 160 for (data = 0, j = 3; j >= 0; j--) { 161 if ((j + index) < fw->size) 162 data |= fw->data[index + j] << (8 * j); 163 } 164 writel(data, regs + RCAR_USB3_FW_DATA0); 165 temp = readl(regs + RCAR_USB3_DL_CTRL); 166 temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0; 167 writel(temp, regs + RCAR_USB3_DL_CTRL); 168 169 for (time = 0; time < timeout; time++) { 170 val = readl(regs + RCAR_USB3_DL_CTRL); 171 if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0) 172 break; 173 udelay(1); 174 } 175 if (time == timeout) { 176 retval = -ETIMEDOUT; 177 break; 178 } 179 } 180 181 temp = readl(regs + RCAR_USB3_DL_CTRL); 182 temp &= ~RCAR_USB3_DL_CTRL_ENABLE; 183 writel(temp, regs + RCAR_USB3_DL_CTRL); 184 185 for (time = 0; time < timeout; time++) { 186 val = readl(regs + RCAR_USB3_DL_CTRL); 187 if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) { 188 retval = 0; 189 break; 190 } 191 udelay(1); 192 } 193 if (time == timeout) 194 retval = -ETIMEDOUT; 195 196 release_firmware(fw); 197 198 return retval; 199 } 200 201 static bool xhci_rcar_wait_for_pll_active(struct usb_hcd *hcd) 202 { 203 int timeout = 1000; 204 u32 val, mask = RCAR_USB3_AXH_STA_PLL_ACTIVE_MASK; 205 206 while (timeout > 0) { 207 val = readl(hcd->regs + RCAR_USB3_AXH_STA); 208 if ((val & mask) == mask) 209 return true; 210 udelay(1); 211 timeout--; 212 } 213 214 return false; 215 } 216 217 /* This function needs to initialize a "phy" of usb before */ 218 int xhci_rcar_init_quirk(struct usb_hcd *hcd) 219 { 220 /* If hcd->regs is NULL, we don't just call the following function */ 221 if (!hcd->regs) 222 return 0; 223 224 if (!xhci_rcar_wait_for_pll_active(hcd)) 225 return -ETIMEDOUT; 226 227 return xhci_rcar_download_firmware(hcd); 228 } 229 230 int xhci_rcar_resume_quirk(struct usb_hcd *hcd) 231 { 232 int ret; 233 234 ret = xhci_rcar_download_firmware(hcd); 235 if (!ret) 236 xhci_rcar_start(hcd); 237 238 return ret; 239 } 240