1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * xHCI host controller driver 4 * 5 * Copyright (C) 2008 Intel Corp. 6 * 7 * Author: Sarah Sharp 8 * Some code borrowed from the Linux EHCI driver. 9 */ 10 11 12 #include <linux/slab.h> 13 #include <asm/unaligned.h> 14 #include <linux/bitfield.h> 15 16 #include "xhci.h" 17 #include "xhci-trace.h" 18 19 #define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E) 20 #define PORT_RWC_BITS (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \ 21 PORT_RC | PORT_PLC | PORT_PE) 22 23 /* Default sublink speed attribute of each lane */ 24 static u32 ssp_cap_default_ssa[] = { 25 0x00050034, /* USB 3.0 SS Gen1x1 id:4 symmetric rx 5Gbps */ 26 0x000500b4, /* USB 3.0 SS Gen1x1 id:4 symmetric tx 5Gbps */ 27 0x000a4035, /* USB 3.1 SSP Gen2x1 id:5 symmetric rx 10Gbps */ 28 0x000a40b5, /* USB 3.1 SSP Gen2x1 id:5 symmetric tx 10Gbps */ 29 0x00054036, /* USB 3.2 SSP Gen1x2 id:6 symmetric rx 5Gbps */ 30 0x000540b6, /* USB 3.2 SSP Gen1x2 id:6 symmetric tx 5Gbps */ 31 0x000a4037, /* USB 3.2 SSP Gen2x2 id:7 symmetric rx 10Gbps */ 32 0x000a40b7, /* USB 3.2 SSP Gen2x2 id:7 symmetric tx 10Gbps */ 33 }; 34 35 static int xhci_create_usb3x_bos_desc(struct xhci_hcd *xhci, char *buf, 36 u16 wLength) 37 { 38 struct usb_bos_descriptor *bos; 39 struct usb_ss_cap_descriptor *ss_cap; 40 struct usb_ssp_cap_descriptor *ssp_cap; 41 struct xhci_port_cap *port_cap = NULL; 42 u16 bcdUSB; 43 u32 reg; 44 u32 min_rate = 0; 45 u8 min_ssid; 46 u8 ssac; 47 u8 ssic; 48 int offset; 49 int i; 50 51 /* BOS descriptor */ 52 bos = (struct usb_bos_descriptor *)buf; 53 bos->bLength = USB_DT_BOS_SIZE; 54 bos->bDescriptorType = USB_DT_BOS; 55 bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE + 56 USB_DT_USB_SS_CAP_SIZE); 57 bos->bNumDeviceCaps = 1; 58 59 /* Create the descriptor for port with the highest revision */ 60 for (i = 0; i < xhci->num_port_caps; i++) { 61 u8 major = xhci->port_caps[i].maj_rev; 62 u8 minor = xhci->port_caps[i].min_rev; 63 u16 rev = (major << 8) | minor; 64 65 if (i == 0 || bcdUSB < rev) { 66 bcdUSB = rev; 67 port_cap = &xhci->port_caps[i]; 68 } 69 } 70 71 if (bcdUSB >= 0x0310) { 72 if (port_cap->psi_count) { 73 u8 num_sym_ssa = 0; 74 75 for (i = 0; i < port_cap->psi_count; i++) { 76 if ((port_cap->psi[i] & PLT_MASK) == PLT_SYM) 77 num_sym_ssa++; 78 } 79 80 ssac = port_cap->psi_count + num_sym_ssa - 1; 81 ssic = port_cap->psi_uid_count - 1; 82 } else { 83 if (bcdUSB >= 0x0320) 84 ssac = 7; 85 else 86 ssac = 3; 87 88 ssic = (ssac + 1) / 2 - 1; 89 } 90 91 bos->bNumDeviceCaps++; 92 bos->wTotalLength = cpu_to_le16(USB_DT_BOS_SIZE + 93 USB_DT_USB_SS_CAP_SIZE + 94 USB_DT_USB_SSP_CAP_SIZE(ssac)); 95 } 96 97 if (wLength < USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE) 98 return wLength; 99 100 /* SuperSpeed USB Device Capability */ 101 ss_cap = (struct usb_ss_cap_descriptor *)&buf[USB_DT_BOS_SIZE]; 102 ss_cap->bLength = USB_DT_USB_SS_CAP_SIZE; 103 ss_cap->bDescriptorType = USB_DT_DEVICE_CAPABILITY; 104 ss_cap->bDevCapabilityType = USB_SS_CAP_TYPE; 105 ss_cap->bmAttributes = 0; /* set later */ 106 ss_cap->wSpeedSupported = cpu_to_le16(USB_5GBPS_OPERATION); 107 ss_cap->bFunctionalitySupport = USB_LOW_SPEED_OPERATION; 108 ss_cap->bU1devExitLat = 0; /* set later */ 109 ss_cap->bU2DevExitLat = 0; /* set later */ 110 111 reg = readl(&xhci->cap_regs->hcc_params); 112 if (HCC_LTC(reg)) 113 ss_cap->bmAttributes |= USB_LTM_SUPPORT; 114 115 if ((xhci->quirks & XHCI_LPM_SUPPORT)) { 116 reg = readl(&xhci->cap_regs->hcs_params3); 117 ss_cap->bU1devExitLat = HCS_U1_LATENCY(reg); 118 ss_cap->bU2DevExitLat = cpu_to_le16(HCS_U2_LATENCY(reg)); 119 } 120 121 if (wLength < le16_to_cpu(bos->wTotalLength)) 122 return wLength; 123 124 if (bcdUSB < 0x0310) 125 return le16_to_cpu(bos->wTotalLength); 126 127 ssp_cap = (struct usb_ssp_cap_descriptor *)&buf[USB_DT_BOS_SIZE + 128 USB_DT_USB_SS_CAP_SIZE]; 129 ssp_cap->bLength = USB_DT_USB_SSP_CAP_SIZE(ssac); 130 ssp_cap->bDescriptorType = USB_DT_DEVICE_CAPABILITY; 131 ssp_cap->bDevCapabilityType = USB_SSP_CAP_TYPE; 132 ssp_cap->bReserved = 0; 133 ssp_cap->wReserved = 0; 134 ssp_cap->bmAttributes = 135 cpu_to_le32(FIELD_PREP(USB_SSP_SUBLINK_SPEED_ATTRIBS, ssac) | 136 FIELD_PREP(USB_SSP_SUBLINK_SPEED_IDS, ssic)); 137 138 if (!port_cap->psi_count) { 139 for (i = 0; i < ssac + 1; i++) 140 ssp_cap->bmSublinkSpeedAttr[i] = 141 cpu_to_le32(ssp_cap_default_ssa[i]); 142 143 min_ssid = 4; 144 goto out; 145 } 146 147 offset = 0; 148 for (i = 0; i < port_cap->psi_count; i++) { 149 u32 psi; 150 u32 attr; 151 u8 ssid; 152 u8 lp; 153 u8 lse; 154 u8 psie; 155 u16 lane_mantissa; 156 u16 psim; 157 u16 plt; 158 159 psi = port_cap->psi[i]; 160 ssid = XHCI_EXT_PORT_PSIV(psi); 161 lp = XHCI_EXT_PORT_LP(psi); 162 psie = XHCI_EXT_PORT_PSIE(psi); 163 psim = XHCI_EXT_PORT_PSIM(psi); 164 plt = psi & PLT_MASK; 165 166 lse = psie; 167 lane_mantissa = psim; 168 169 /* Shift to Gbps and set SSP Link Protocol if 10Gpbs */ 170 for (; psie < USB_SSP_SUBLINK_SPEED_LSE_GBPS; psie++) 171 psim /= 1000; 172 173 if (!min_rate || psim < min_rate) { 174 min_ssid = ssid; 175 min_rate = psim; 176 } 177 178 /* Some host controllers don't set the link protocol for SSP */ 179 if (psim >= 10) 180 lp = USB_SSP_SUBLINK_SPEED_LP_SSP; 181 182 /* 183 * PSIM and PSIE represent the total speed of PSI. The BOS 184 * descriptor SSP sublink speed attribute lane mantissa 185 * describes the lane speed. E.g. PSIM and PSIE for gen2x2 186 * is 20Gbps, but the BOS descriptor lane speed mantissa is 187 * 10Gbps. Check and modify the mantissa value to match the 188 * lane speed. 189 */ 190 if (bcdUSB == 0x0320 && plt == PLT_SYM) { 191 /* 192 * The PSI dword for gen1x2 and gen2x1 share the same 193 * values. But the lane speed for gen1x2 is 5Gbps while 194 * gen2x1 is 10Gbps. If the previous PSI dword SSID is 195 * 5 and the PSIE and PSIM match with SSID 6, let's 196 * assume that the controller follows the default speed 197 * id with SSID 6 for gen1x2. 198 */ 199 if (ssid == 6 && psie == 3 && psim == 10 && i) { 200 u32 prev = port_cap->psi[i - 1]; 201 202 if ((prev & PLT_MASK) == PLT_SYM && 203 XHCI_EXT_PORT_PSIV(prev) == 5 && 204 XHCI_EXT_PORT_PSIE(prev) == 3 && 205 XHCI_EXT_PORT_PSIM(prev) == 10) { 206 lse = USB_SSP_SUBLINK_SPEED_LSE_GBPS; 207 lane_mantissa = 5; 208 } 209 } 210 211 if (psie == 3 && psim > 10) { 212 lse = USB_SSP_SUBLINK_SPEED_LSE_GBPS; 213 lane_mantissa = 10; 214 } 215 } 216 217 attr = (FIELD_PREP(USB_SSP_SUBLINK_SPEED_SSID, ssid) | 218 FIELD_PREP(USB_SSP_SUBLINK_SPEED_LP, lp) | 219 FIELD_PREP(USB_SSP_SUBLINK_SPEED_LSE, lse) | 220 FIELD_PREP(USB_SSP_SUBLINK_SPEED_LSM, lane_mantissa)); 221 222 switch (plt) { 223 case PLT_SYM: 224 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 225 USB_SSP_SUBLINK_SPEED_ST_SYM_RX); 226 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 227 228 attr &= ~USB_SSP_SUBLINK_SPEED_ST; 229 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 230 USB_SSP_SUBLINK_SPEED_ST_SYM_TX); 231 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 232 break; 233 case PLT_ASYM_RX: 234 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 235 USB_SSP_SUBLINK_SPEED_ST_ASYM_RX); 236 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 237 break; 238 case PLT_ASYM_TX: 239 attr |= FIELD_PREP(USB_SSP_SUBLINK_SPEED_ST, 240 USB_SSP_SUBLINK_SPEED_ST_ASYM_TX); 241 ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr); 242 break; 243 } 244 } 245 out: 246 ssp_cap->wFunctionalitySupport = 247 cpu_to_le16(FIELD_PREP(USB_SSP_MIN_SUBLINK_SPEED_ATTRIBUTE_ID, 248 min_ssid) | 249 FIELD_PREP(USB_SSP_MIN_RX_LANE_COUNT, 1) | 250 FIELD_PREP(USB_SSP_MIN_TX_LANE_COUNT, 1)); 251 252 return le16_to_cpu(bos->wTotalLength); 253 } 254 255 static void xhci_common_hub_descriptor(struct xhci_hcd *xhci, 256 struct usb_hub_descriptor *desc, int ports) 257 { 258 u16 temp; 259 260 desc->bHubContrCurrent = 0; 261 262 desc->bNbrPorts = ports; 263 temp = 0; 264 /* Bits 1:0 - support per-port power switching, or power always on */ 265 if (HCC_PPC(xhci->hcc_params)) 266 temp |= HUB_CHAR_INDV_PORT_LPSM; 267 else 268 temp |= HUB_CHAR_NO_LPSM; 269 /* Bit 2 - root hubs are not part of a compound device */ 270 /* Bits 4:3 - individual port over current protection */ 271 temp |= HUB_CHAR_INDV_PORT_OCPM; 272 /* Bits 6:5 - no TTs in root ports */ 273 /* Bit 7 - no port indicators */ 274 desc->wHubCharacteristics = cpu_to_le16(temp); 275 } 276 277 /* Fill in the USB 2.0 roothub descriptor */ 278 static void xhci_usb2_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci, 279 struct usb_hub_descriptor *desc) 280 { 281 int ports; 282 u16 temp; 283 __u8 port_removable[(USB_MAXCHILDREN + 1 + 7) / 8]; 284 u32 portsc; 285 unsigned int i; 286 struct xhci_hub *rhub; 287 288 rhub = &xhci->usb2_rhub; 289 ports = rhub->num_ports; 290 xhci_common_hub_descriptor(xhci, desc, ports); 291 desc->bDescriptorType = USB_DT_HUB; 292 temp = 1 + (ports / 8); 293 desc->bDescLength = USB_DT_HUB_NONVAR_SIZE + 2 * temp; 294 desc->bPwrOn2PwrGood = 10; /* xhci section 5.4.8 says 20ms */ 295 296 /* The Device Removable bits are reported on a byte granularity. 297 * If the port doesn't exist within that byte, the bit is set to 0. 298 */ 299 memset(port_removable, 0, sizeof(port_removable)); 300 for (i = 0; i < ports; i++) { 301 portsc = readl(rhub->ports[i]->addr); 302 /* If a device is removable, PORTSC reports a 0, same as in the 303 * hub descriptor DeviceRemovable bits. 304 */ 305 if (portsc & PORT_DEV_REMOVE) 306 /* This math is hairy because bit 0 of DeviceRemovable 307 * is reserved, and bit 1 is for port 1, etc. 308 */ 309 port_removable[(i + 1) / 8] |= 1 << ((i + 1) % 8); 310 } 311 312 /* ch11.h defines a hub descriptor that has room for USB_MAXCHILDREN 313 * ports on it. The USB 2.0 specification says that there are two 314 * variable length fields at the end of the hub descriptor: 315 * DeviceRemovable and PortPwrCtrlMask. But since we can have less than 316 * USB_MAXCHILDREN ports, we may need to use the DeviceRemovable array 317 * to set PortPwrCtrlMask bits. PortPwrCtrlMask must always be set to 318 * 0xFF, so we initialize the both arrays (DeviceRemovable and 319 * PortPwrCtrlMask) to 0xFF. Then we set the DeviceRemovable for each 320 * set of ports that actually exist. 321 */ 322 memset(desc->u.hs.DeviceRemovable, 0xff, 323 sizeof(desc->u.hs.DeviceRemovable)); 324 memset(desc->u.hs.PortPwrCtrlMask, 0xff, 325 sizeof(desc->u.hs.PortPwrCtrlMask)); 326 327 for (i = 0; i < (ports + 1 + 7) / 8; i++) 328 memset(&desc->u.hs.DeviceRemovable[i], port_removable[i], 329 sizeof(__u8)); 330 } 331 332 /* Fill in the USB 3.0 roothub descriptor */ 333 static void xhci_usb3_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci, 334 struct usb_hub_descriptor *desc) 335 { 336 int ports; 337 u16 port_removable; 338 u32 portsc; 339 unsigned int i; 340 struct xhci_hub *rhub; 341 342 rhub = &xhci->usb3_rhub; 343 ports = rhub->num_ports; 344 xhci_common_hub_descriptor(xhci, desc, ports); 345 desc->bDescriptorType = USB_DT_SS_HUB; 346 desc->bDescLength = USB_DT_SS_HUB_SIZE; 347 desc->bPwrOn2PwrGood = 50; /* usb 3.1 may fail if less than 100ms */ 348 349 /* header decode latency should be zero for roothubs, 350 * see section 4.23.5.2. 351 */ 352 desc->u.ss.bHubHdrDecLat = 0; 353 desc->u.ss.wHubDelay = 0; 354 355 port_removable = 0; 356 /* bit 0 is reserved, bit 1 is for port 1, etc. */ 357 for (i = 0; i < ports; i++) { 358 portsc = readl(rhub->ports[i]->addr); 359 if (portsc & PORT_DEV_REMOVE) 360 port_removable |= 1 << (i + 1); 361 } 362 363 desc->u.ss.DeviceRemovable = cpu_to_le16(port_removable); 364 } 365 366 static void xhci_hub_descriptor(struct usb_hcd *hcd, struct xhci_hcd *xhci, 367 struct usb_hub_descriptor *desc) 368 { 369 370 if (hcd->speed >= HCD_USB3) 371 xhci_usb3_hub_descriptor(hcd, xhci, desc); 372 else 373 xhci_usb2_hub_descriptor(hcd, xhci, desc); 374 375 } 376 377 static unsigned int xhci_port_speed(unsigned int port_status) 378 { 379 if (DEV_LOWSPEED(port_status)) 380 return USB_PORT_STAT_LOW_SPEED; 381 if (DEV_HIGHSPEED(port_status)) 382 return USB_PORT_STAT_HIGH_SPEED; 383 /* 384 * FIXME: Yes, we should check for full speed, but the core uses that as 385 * a default in portspeed() in usb/core/hub.c (which is the only place 386 * USB_PORT_STAT_*_SPEED is used). 387 */ 388 return 0; 389 } 390 391 /* 392 * These bits are Read Only (RO) and should be saved and written to the 393 * registers: 0, 3, 10:13, 30 394 * connect status, over-current status, port speed, and device removable. 395 * connect status and port speed are also sticky - meaning they're in 396 * the AUX well and they aren't changed by a hot, warm, or cold reset. 397 */ 398 #define XHCI_PORT_RO ((1<<0) | (1<<3) | (0xf<<10) | (1<<30)) 399 /* 400 * These bits are RW; writing a 0 clears the bit, writing a 1 sets the bit: 401 * bits 5:8, 9, 14:15, 25:27 402 * link state, port power, port indicator state, "wake on" enable state 403 */ 404 #define XHCI_PORT_RWS ((0xf<<5) | (1<<9) | (0x3<<14) | (0x7<<25)) 405 /* 406 * These bits are RW; writing a 1 sets the bit, writing a 0 has no effect: 407 * bit 4 (port reset) 408 */ 409 #define XHCI_PORT_RW1S ((1<<4)) 410 /* 411 * These bits are RW; writing a 1 clears the bit, writing a 0 has no effect: 412 * bits 1, 17, 18, 19, 20, 21, 22, 23 413 * port enable/disable, and 414 * change bits: connect, PED, warm port reset changed (reserved zero for USB 2.0 ports), 415 * over-current, reset, link state, and L1 change 416 */ 417 #define XHCI_PORT_RW1CS ((1<<1) | (0x7f<<17)) 418 /* 419 * Bit 16 is RW, and writing a '1' to it causes the link state control to be 420 * latched in 421 */ 422 #define XHCI_PORT_RW ((1<<16)) 423 /* 424 * These bits are Reserved Zero (RsvdZ) and zero should be written to them: 425 * bits 2, 24, 28:31 426 */ 427 #define XHCI_PORT_RZ ((1<<2) | (1<<24) | (0xf<<28)) 428 429 /** 430 * xhci_port_state_to_neutral() - Clean up read portsc value back into writeable 431 * @state: u32 port value read from portsc register to be cleanup up 432 * 433 * Given a port state, this function returns a value that would result in the 434 * port being in the same state, if the value was written to the port status 435 * control register. 436 * Save Read Only (RO) bits and save read/write bits where 437 * writing a 0 clears the bit and writing a 1 sets the bit (RWS). 438 * For all other types (RW1S, RW1CS, RW, and RZ), writing a '0' has no effect. 439 * 440 * Return: u32 value that can be written back to portsc register without 441 * changing port state. 442 */ 443 444 u32 xhci_port_state_to_neutral(u32 state) 445 { 446 /* Save read-only status and port state */ 447 return (state & XHCI_PORT_RO) | (state & XHCI_PORT_RWS); 448 } 449 EXPORT_SYMBOL_GPL(xhci_port_state_to_neutral); 450 451 /** 452 * xhci_find_slot_id_by_port() - Find slot id of a usb device on a roothub port 453 * @hcd: pointer to hcd of the roothub 454 * @xhci: pointer to xhci structure 455 * @port: one-based port number of the port in this roothub. 456 * 457 * Return: Slot id of the usb device connected to the root port, 0 if not found 458 */ 459 460 int xhci_find_slot_id_by_port(struct usb_hcd *hcd, struct xhci_hcd *xhci, 461 u16 port) 462 { 463 int slot_id; 464 int i; 465 enum usb_device_speed speed; 466 467 slot_id = 0; 468 for (i = 0; i < MAX_HC_SLOTS; i++) { 469 if (!xhci->devs[i] || !xhci->devs[i]->udev) 470 continue; 471 speed = xhci->devs[i]->udev->speed; 472 if (((speed >= USB_SPEED_SUPER) == (hcd->speed >= HCD_USB3)) 473 && xhci->devs[i]->fake_port == port) { 474 slot_id = i; 475 break; 476 } 477 } 478 479 return slot_id; 480 } 481 EXPORT_SYMBOL_GPL(xhci_find_slot_id_by_port); 482 483 /* 484 * Stop device 485 * It issues stop endpoint command for EP 0 to 30. And wait the last command 486 * to complete. 487 * suspend will set to 1, if suspend bit need to set in command. 488 */ 489 static int xhci_stop_device(struct xhci_hcd *xhci, int slot_id, int suspend) 490 { 491 struct xhci_virt_device *virt_dev; 492 struct xhci_command *cmd; 493 unsigned long flags; 494 int ret; 495 int i; 496 497 ret = 0; 498 virt_dev = xhci->devs[slot_id]; 499 if (!virt_dev) 500 return -ENODEV; 501 502 trace_xhci_stop_device(virt_dev); 503 504 cmd = xhci_alloc_command(xhci, true, GFP_NOIO); 505 if (!cmd) 506 return -ENOMEM; 507 508 spin_lock_irqsave(&xhci->lock, flags); 509 for (i = LAST_EP_INDEX; i > 0; i--) { 510 if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue) { 511 struct xhci_ep_ctx *ep_ctx; 512 struct xhci_command *command; 513 514 ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->out_ctx, i); 515 516 /* Check ep is running, required by AMD SNPS 3.1 xHC */ 517 if (GET_EP_CTX_STATE(ep_ctx) != EP_STATE_RUNNING) 518 continue; 519 520 command = xhci_alloc_command(xhci, false, GFP_NOWAIT); 521 if (!command) { 522 spin_unlock_irqrestore(&xhci->lock, flags); 523 ret = -ENOMEM; 524 goto cmd_cleanup; 525 } 526 527 ret = xhci_queue_stop_endpoint(xhci, command, slot_id, 528 i, suspend); 529 if (ret) { 530 spin_unlock_irqrestore(&xhci->lock, flags); 531 xhci_free_command(xhci, command); 532 goto cmd_cleanup; 533 } 534 } 535 } 536 ret = xhci_queue_stop_endpoint(xhci, cmd, slot_id, 0, suspend); 537 if (ret) { 538 spin_unlock_irqrestore(&xhci->lock, flags); 539 goto cmd_cleanup; 540 } 541 542 xhci_ring_cmd_db(xhci); 543 spin_unlock_irqrestore(&xhci->lock, flags); 544 545 /* Wait for last stop endpoint command to finish */ 546 wait_for_completion(cmd->completion); 547 548 if (cmd->status == COMP_COMMAND_ABORTED || 549 cmd->status == COMP_COMMAND_RING_STOPPED) { 550 xhci_warn(xhci, "Timeout while waiting for stop endpoint command\n"); 551 ret = -ETIME; 552 } 553 554 cmd_cleanup: 555 xhci_free_command(xhci, cmd); 556 return ret; 557 } 558 559 /* 560 * Ring device, it rings the all doorbells unconditionally. 561 */ 562 void xhci_ring_device(struct xhci_hcd *xhci, int slot_id) 563 { 564 int i, s; 565 struct xhci_virt_ep *ep; 566 567 for (i = 0; i < LAST_EP_INDEX + 1; i++) { 568 ep = &xhci->devs[slot_id]->eps[i]; 569 570 if (ep->ep_state & EP_HAS_STREAMS) { 571 for (s = 1; s < ep->stream_info->num_streams; s++) 572 xhci_ring_ep_doorbell(xhci, slot_id, i, s); 573 } else if (ep->ring && ep->ring->dequeue) { 574 xhci_ring_ep_doorbell(xhci, slot_id, i, 0); 575 } 576 } 577 578 return; 579 } 580 581 static void xhci_disable_port(struct xhci_hcd *xhci, struct xhci_port *port) 582 { 583 struct usb_hcd *hcd; 584 u32 portsc; 585 586 hcd = port->rhub->hcd; 587 588 /* Don't allow the USB core to disable SuperSpeed ports. */ 589 if (hcd->speed >= HCD_USB3) { 590 xhci_dbg(xhci, "Ignoring request to disable SuperSpeed port.\n"); 591 return; 592 } 593 594 if (xhci->quirks & XHCI_BROKEN_PORT_PED) { 595 xhci_dbg(xhci, 596 "Broken Port Enabled/Disabled, ignoring port disable request.\n"); 597 return; 598 } 599 600 portsc = readl(port->addr); 601 portsc = xhci_port_state_to_neutral(portsc); 602 603 /* Write 1 to disable the port */ 604 writel(portsc | PORT_PE, port->addr); 605 606 portsc = readl(port->addr); 607 xhci_dbg(xhci, "disable port %d-%d, portsc: 0x%x\n", 608 hcd->self.busnum, port->hcd_portnum + 1, portsc); 609 } 610 611 static void xhci_clear_port_change_bit(struct xhci_hcd *xhci, u16 wValue, 612 u16 wIndex, __le32 __iomem *addr, u32 port_status) 613 { 614 char *port_change_bit; 615 u32 status; 616 617 switch (wValue) { 618 case USB_PORT_FEAT_C_RESET: 619 status = PORT_RC; 620 port_change_bit = "reset"; 621 break; 622 case USB_PORT_FEAT_C_BH_PORT_RESET: 623 status = PORT_WRC; 624 port_change_bit = "warm(BH) reset"; 625 break; 626 case USB_PORT_FEAT_C_CONNECTION: 627 status = PORT_CSC; 628 port_change_bit = "connect"; 629 break; 630 case USB_PORT_FEAT_C_OVER_CURRENT: 631 status = PORT_OCC; 632 port_change_bit = "over-current"; 633 break; 634 case USB_PORT_FEAT_C_ENABLE: 635 status = PORT_PEC; 636 port_change_bit = "enable/disable"; 637 break; 638 case USB_PORT_FEAT_C_SUSPEND: 639 status = PORT_PLC; 640 port_change_bit = "suspend/resume"; 641 break; 642 case USB_PORT_FEAT_C_PORT_LINK_STATE: 643 status = PORT_PLC; 644 port_change_bit = "link state"; 645 break; 646 case USB_PORT_FEAT_C_PORT_CONFIG_ERROR: 647 status = PORT_CEC; 648 port_change_bit = "config error"; 649 break; 650 default: 651 /* Should never happen */ 652 return; 653 } 654 /* Change bits are all write 1 to clear */ 655 writel(port_status | status, addr); 656 port_status = readl(addr); 657 658 xhci_dbg(xhci, "clear port%d %s change, portsc: 0x%x\n", 659 wIndex + 1, port_change_bit, port_status); 660 } 661 662 struct xhci_hub *xhci_get_rhub(struct usb_hcd *hcd) 663 { 664 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 665 666 if (hcd->speed >= HCD_USB3) 667 return &xhci->usb3_rhub; 668 return &xhci->usb2_rhub; 669 } 670 671 /* 672 * xhci_set_port_power() must be called with xhci->lock held. 673 * It will release and re-aquire the lock while calling ACPI 674 * method. 675 */ 676 static void xhci_set_port_power(struct xhci_hcd *xhci, struct xhci_port *port, 677 bool on, unsigned long *flags) 678 __must_hold(&xhci->lock) 679 { 680 struct usb_hcd *hcd; 681 u32 temp; 682 683 hcd = port->rhub->hcd; 684 temp = readl(port->addr); 685 686 xhci_dbg(xhci, "set port power %d-%d %s, portsc: 0x%x\n", 687 hcd->self.busnum, port->hcd_portnum + 1, on ? "ON" : "OFF", temp); 688 689 temp = xhci_port_state_to_neutral(temp); 690 691 if (on) { 692 /* Power on */ 693 writel(temp | PORT_POWER, port->addr); 694 readl(port->addr); 695 } else { 696 /* Power off */ 697 writel(temp & ~PORT_POWER, port->addr); 698 } 699 700 spin_unlock_irqrestore(&xhci->lock, *flags); 701 temp = usb_acpi_power_manageable(hcd->self.root_hub, 702 port->hcd_portnum); 703 if (temp) 704 usb_acpi_set_power_state(hcd->self.root_hub, 705 port->hcd_portnum, on); 706 spin_lock_irqsave(&xhci->lock, *flags); 707 } 708 709 static void xhci_port_set_test_mode(struct xhci_hcd *xhci, 710 u16 test_mode, u16 wIndex) 711 { 712 u32 temp; 713 struct xhci_port *port; 714 715 /* xhci only supports test mode for usb2 ports */ 716 port = xhci->usb2_rhub.ports[wIndex]; 717 temp = readl(port->addr + PORTPMSC); 718 temp |= test_mode << PORT_TEST_MODE_SHIFT; 719 writel(temp, port->addr + PORTPMSC); 720 xhci->test_mode = test_mode; 721 if (test_mode == USB_TEST_FORCE_ENABLE) 722 xhci_start(xhci); 723 } 724 725 static int xhci_enter_test_mode(struct xhci_hcd *xhci, 726 u16 test_mode, u16 wIndex, unsigned long *flags) 727 __must_hold(&xhci->lock) 728 { 729 int i, retval; 730 731 /* Disable all Device Slots */ 732 xhci_dbg(xhci, "Disable all slots\n"); 733 spin_unlock_irqrestore(&xhci->lock, *flags); 734 for (i = 1; i <= HCS_MAX_SLOTS(xhci->hcs_params1); i++) { 735 if (!xhci->devs[i]) 736 continue; 737 738 retval = xhci_disable_slot(xhci, i); 739 xhci_free_virt_device(xhci, i); 740 if (retval) 741 xhci_err(xhci, "Failed to disable slot %d, %d. Enter test mode anyway\n", 742 i, retval); 743 } 744 spin_lock_irqsave(&xhci->lock, *flags); 745 /* Put all ports to the Disable state by clear PP */ 746 xhci_dbg(xhci, "Disable all port (PP = 0)\n"); 747 /* Power off USB3 ports*/ 748 for (i = 0; i < xhci->usb3_rhub.num_ports; i++) 749 xhci_set_port_power(xhci, xhci->usb3_rhub.ports[i], false, flags); 750 /* Power off USB2 ports*/ 751 for (i = 0; i < xhci->usb2_rhub.num_ports; i++) 752 xhci_set_port_power(xhci, xhci->usb2_rhub.ports[i], false, flags); 753 /* Stop the controller */ 754 xhci_dbg(xhci, "Stop controller\n"); 755 retval = xhci_halt(xhci); 756 if (retval) 757 return retval; 758 /* Disable runtime PM for test mode */ 759 pm_runtime_forbid(xhci_to_hcd(xhci)->self.controller); 760 /* Set PORTPMSC.PTC field to enter selected test mode */ 761 /* Port is selected by wIndex. port_id = wIndex + 1 */ 762 xhci_dbg(xhci, "Enter Test Mode: %d, Port_id=%d\n", 763 test_mode, wIndex + 1); 764 xhci_port_set_test_mode(xhci, test_mode, wIndex); 765 return retval; 766 } 767 768 static int xhci_exit_test_mode(struct xhci_hcd *xhci) 769 { 770 int retval; 771 772 if (!xhci->test_mode) { 773 xhci_err(xhci, "Not in test mode, do nothing.\n"); 774 return 0; 775 } 776 if (xhci->test_mode == USB_TEST_FORCE_ENABLE && 777 !(xhci->xhc_state & XHCI_STATE_HALTED)) { 778 retval = xhci_halt(xhci); 779 if (retval) 780 return retval; 781 } 782 pm_runtime_allow(xhci_to_hcd(xhci)->self.controller); 783 xhci->test_mode = 0; 784 return xhci_reset(xhci, XHCI_RESET_SHORT_USEC); 785 } 786 787 void xhci_set_link_state(struct xhci_hcd *xhci, struct xhci_port *port, 788 u32 link_state) 789 { 790 u32 temp; 791 u32 portsc; 792 793 portsc = readl(port->addr); 794 temp = xhci_port_state_to_neutral(portsc); 795 temp &= ~PORT_PLS_MASK; 796 temp |= PORT_LINK_STROBE | link_state; 797 writel(temp, port->addr); 798 799 xhci_dbg(xhci, "Set port %d-%d link state, portsc: 0x%x, write 0x%x", 800 port->rhub->hcd->self.busnum, port->hcd_portnum + 1, 801 portsc, temp); 802 } 803 804 static void xhci_set_remote_wake_mask(struct xhci_hcd *xhci, 805 struct xhci_port *port, u16 wake_mask) 806 { 807 u32 temp; 808 809 temp = readl(port->addr); 810 temp = xhci_port_state_to_neutral(temp); 811 812 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_CONNECT) 813 temp |= PORT_WKCONN_E; 814 else 815 temp &= ~PORT_WKCONN_E; 816 817 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_DISCONNECT) 818 temp |= PORT_WKDISC_E; 819 else 820 temp &= ~PORT_WKDISC_E; 821 822 if (wake_mask & USB_PORT_FEAT_REMOTE_WAKE_OVER_CURRENT) 823 temp |= PORT_WKOC_E; 824 else 825 temp &= ~PORT_WKOC_E; 826 827 writel(temp, port->addr); 828 } 829 830 /* Test and clear port RWC bit */ 831 void xhci_test_and_clear_bit(struct xhci_hcd *xhci, struct xhci_port *port, 832 u32 port_bit) 833 { 834 u32 temp; 835 836 temp = readl(port->addr); 837 if (temp & port_bit) { 838 temp = xhci_port_state_to_neutral(temp); 839 temp |= port_bit; 840 writel(temp, port->addr); 841 } 842 } 843 844 /* Updates Link Status for super Speed port */ 845 static void xhci_hub_report_usb3_link_state(struct xhci_hcd *xhci, 846 u32 *status, u32 status_reg) 847 { 848 u32 pls = status_reg & PORT_PLS_MASK; 849 850 /* When the CAS bit is set then warm reset 851 * should be performed on port 852 */ 853 if (status_reg & PORT_CAS) { 854 /* The CAS bit can be set while the port is 855 * in any link state. 856 * Only roothubs have CAS bit, so we 857 * pretend to be in compliance mode 858 * unless we're already in compliance 859 * or the inactive state. 860 */ 861 if (pls != USB_SS_PORT_LS_COMP_MOD && 862 pls != USB_SS_PORT_LS_SS_INACTIVE) { 863 pls = USB_SS_PORT_LS_COMP_MOD; 864 } 865 /* Return also connection bit - 866 * hub state machine resets port 867 * when this bit is set. 868 */ 869 pls |= USB_PORT_STAT_CONNECTION; 870 } else { 871 /* 872 * Resume state is an xHCI internal state. Do not report it to 873 * usb core, instead, pretend to be U3, thus usb core knows 874 * it's not ready for transfer. 875 */ 876 if (pls == XDEV_RESUME) { 877 *status |= USB_SS_PORT_LS_U3; 878 return; 879 } 880 881 /* 882 * If CAS bit isn't set but the Port is already at 883 * Compliance Mode, fake a connection so the USB core 884 * notices the Compliance state and resets the port. 885 * This resolves an issue generated by the SN65LVPE502CP 886 * in which sometimes the port enters compliance mode 887 * caused by a delay on the host-device negotiation. 888 */ 889 if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && 890 (pls == USB_SS_PORT_LS_COMP_MOD)) 891 pls |= USB_PORT_STAT_CONNECTION; 892 } 893 894 /* update status field */ 895 *status |= pls; 896 } 897 898 /* 899 * Function for Compliance Mode Quirk. 900 * 901 * This Function verifies if all xhc USB3 ports have entered U0, if so, 902 * the compliance mode timer is deleted. A port won't enter 903 * compliance mode if it has previously entered U0. 904 */ 905 static void xhci_del_comp_mod_timer(struct xhci_hcd *xhci, u32 status, 906 u16 wIndex) 907 { 908 u32 all_ports_seen_u0 = ((1 << xhci->usb3_rhub.num_ports) - 1); 909 bool port_in_u0 = ((status & PORT_PLS_MASK) == XDEV_U0); 910 911 if (!(xhci->quirks & XHCI_COMP_MODE_QUIRK)) 912 return; 913 914 if ((xhci->port_status_u0 != all_ports_seen_u0) && port_in_u0) { 915 xhci->port_status_u0 |= 1 << wIndex; 916 if (xhci->port_status_u0 == all_ports_seen_u0) { 917 del_timer_sync(&xhci->comp_mode_recovery_timer); 918 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, 919 "All USB3 ports have entered U0 already!"); 920 xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, 921 "Compliance Mode Recovery Timer Deleted."); 922 } 923 } 924 } 925 926 static int xhci_handle_usb2_port_link_resume(struct xhci_port *port, 927 u32 portsc, 928 unsigned long *flags) 929 { 930 struct xhci_bus_state *bus_state; 931 struct xhci_hcd *xhci; 932 struct usb_hcd *hcd; 933 int slot_id; 934 u32 wIndex; 935 936 hcd = port->rhub->hcd; 937 bus_state = &port->rhub->bus_state; 938 xhci = hcd_to_xhci(hcd); 939 wIndex = port->hcd_portnum; 940 941 if ((portsc & PORT_RESET) || !(portsc & PORT_PE)) { 942 return -EINVAL; 943 } 944 /* did port event handler already start resume timing? */ 945 if (!port->resume_timestamp) { 946 /* If not, maybe we are in a host initated resume? */ 947 if (test_bit(wIndex, &bus_state->resuming_ports)) { 948 /* Host initated resume doesn't time the resume 949 * signalling using resume_done[]. 950 * It manually sets RESUME state, sleeps 20ms 951 * and sets U0 state. This should probably be 952 * changed, but not right now. 953 */ 954 } else { 955 /* port resume was discovered now and here, 956 * start resume timing 957 */ 958 unsigned long timeout = jiffies + 959 msecs_to_jiffies(USB_RESUME_TIMEOUT); 960 961 set_bit(wIndex, &bus_state->resuming_ports); 962 port->resume_timestamp = timeout; 963 mod_timer(&hcd->rh_timer, timeout); 964 usb_hcd_start_port_resume(&hcd->self, wIndex); 965 } 966 /* Has resume been signalled for USB_RESUME_TIME yet? */ 967 } else if (time_after_eq(jiffies, port->resume_timestamp)) { 968 int time_left; 969 970 xhci_dbg(xhci, "resume USB2 port %d-%d\n", 971 hcd->self.busnum, wIndex + 1); 972 973 port->resume_timestamp = 0; 974 clear_bit(wIndex, &bus_state->resuming_ports); 975 976 reinit_completion(&port->rexit_done); 977 port->rexit_active = true; 978 979 xhci_test_and_clear_bit(xhci, port, PORT_PLC); 980 xhci_set_link_state(xhci, port, XDEV_U0); 981 982 spin_unlock_irqrestore(&xhci->lock, *flags); 983 time_left = wait_for_completion_timeout( 984 &port->rexit_done, 985 msecs_to_jiffies(XHCI_MAX_REXIT_TIMEOUT_MS)); 986 spin_lock_irqsave(&xhci->lock, *flags); 987 988 if (time_left) { 989 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 990 wIndex + 1); 991 if (!slot_id) { 992 xhci_dbg(xhci, "slot_id is zero\n"); 993 return -ENODEV; 994 } 995 xhci_ring_device(xhci, slot_id); 996 } else { 997 int port_status = readl(port->addr); 998 999 xhci_warn(xhci, "Port resume timed out, port %d-%d: 0x%x\n", 1000 hcd->self.busnum, wIndex + 1, port_status); 1001 /* 1002 * keep rexit_active set if U0 transition failed so we 1003 * know to report PORT_STAT_SUSPEND status back to 1004 * usbcore. It will be cleared later once the port is 1005 * out of RESUME/U3 state 1006 */ 1007 } 1008 1009 usb_hcd_end_port_resume(&hcd->self, wIndex); 1010 bus_state->port_c_suspend |= 1 << wIndex; 1011 bus_state->suspended_ports &= ~(1 << wIndex); 1012 } 1013 1014 return 0; 1015 } 1016 1017 static u32 xhci_get_ext_port_status(u32 raw_port_status, u32 port_li) 1018 { 1019 u32 ext_stat = 0; 1020 int speed_id; 1021 1022 /* only support rx and tx lane counts of 1 in usb3.1 spec */ 1023 speed_id = DEV_PORT_SPEED(raw_port_status); 1024 ext_stat |= speed_id; /* bits 3:0, RX speed id */ 1025 ext_stat |= speed_id << 4; /* bits 7:4, TX speed id */ 1026 1027 ext_stat |= PORT_RX_LANES(port_li) << 8; /* bits 11:8 Rx lane count */ 1028 ext_stat |= PORT_TX_LANES(port_li) << 12; /* bits 15:12 Tx lane count */ 1029 1030 return ext_stat; 1031 } 1032 1033 static void xhci_get_usb3_port_status(struct xhci_port *port, u32 *status, 1034 u32 portsc) 1035 { 1036 struct xhci_bus_state *bus_state; 1037 struct xhci_hcd *xhci; 1038 struct usb_hcd *hcd; 1039 u32 link_state; 1040 u32 portnum; 1041 1042 bus_state = &port->rhub->bus_state; 1043 xhci = hcd_to_xhci(port->rhub->hcd); 1044 hcd = port->rhub->hcd; 1045 link_state = portsc & PORT_PLS_MASK; 1046 portnum = port->hcd_portnum; 1047 1048 /* USB3 specific wPortChange bits 1049 * 1050 * Port link change with port in resume state should not be 1051 * reported to usbcore, as this is an internal state to be 1052 * handled by xhci driver. Reporting PLC to usbcore may 1053 * cause usbcore clearing PLC first and port change event 1054 * irq won't be generated. 1055 */ 1056 1057 if (portsc & PORT_PLC && (link_state != XDEV_RESUME)) 1058 *status |= USB_PORT_STAT_C_LINK_STATE << 16; 1059 if (portsc & PORT_WRC) 1060 *status |= USB_PORT_STAT_C_BH_RESET << 16; 1061 if (portsc & PORT_CEC) 1062 *status |= USB_PORT_STAT_C_CONFIG_ERROR << 16; 1063 1064 /* USB3 specific wPortStatus bits */ 1065 if (portsc & PORT_POWER) 1066 *status |= USB_SS_PORT_STAT_POWER; 1067 1068 /* no longer suspended or resuming */ 1069 if (link_state != XDEV_U3 && 1070 link_state != XDEV_RESUME && 1071 link_state != XDEV_RECOVERY) { 1072 /* remote wake resume signaling complete */ 1073 if (bus_state->port_remote_wakeup & (1 << portnum)) { 1074 bus_state->port_remote_wakeup &= ~(1 << portnum); 1075 usb_hcd_end_port_resume(&hcd->self, portnum); 1076 } 1077 bus_state->suspended_ports &= ~(1 << portnum); 1078 } 1079 1080 xhci_hub_report_usb3_link_state(xhci, status, portsc); 1081 xhci_del_comp_mod_timer(xhci, portsc, portnum); 1082 } 1083 1084 static void xhci_get_usb2_port_status(struct xhci_port *port, u32 *status, 1085 u32 portsc, unsigned long *flags) 1086 { 1087 struct xhci_bus_state *bus_state; 1088 u32 link_state; 1089 u32 portnum; 1090 int err; 1091 1092 bus_state = &port->rhub->bus_state; 1093 link_state = portsc & PORT_PLS_MASK; 1094 portnum = port->hcd_portnum; 1095 1096 /* USB2 wPortStatus bits */ 1097 if (portsc & PORT_POWER) { 1098 *status |= USB_PORT_STAT_POWER; 1099 1100 /* link state is only valid if port is powered */ 1101 if (link_state == XDEV_U3) 1102 *status |= USB_PORT_STAT_SUSPEND; 1103 if (link_state == XDEV_U2) 1104 *status |= USB_PORT_STAT_L1; 1105 if (link_state == XDEV_U0) { 1106 if (bus_state->suspended_ports & (1 << portnum)) { 1107 bus_state->suspended_ports &= ~(1 << portnum); 1108 bus_state->port_c_suspend |= 1 << portnum; 1109 } 1110 } 1111 if (link_state == XDEV_RESUME) { 1112 err = xhci_handle_usb2_port_link_resume(port, portsc, 1113 flags); 1114 if (err < 0) 1115 *status = 0xffffffff; 1116 else if (port->resume_timestamp || port->rexit_active) 1117 *status |= USB_PORT_STAT_SUSPEND; 1118 } 1119 } 1120 1121 /* 1122 * Clear usb2 resume signalling variables if port is no longer suspended 1123 * or resuming. Port either resumed to U0/U1/U2, disconnected, or in a 1124 * error state. Resume related variables should be cleared in all those cases. 1125 */ 1126 if (link_state != XDEV_U3 && link_state != XDEV_RESUME) { 1127 if (port->resume_timestamp || 1128 test_bit(portnum, &bus_state->resuming_ports)) { 1129 port->resume_timestamp = 0; 1130 clear_bit(portnum, &bus_state->resuming_ports); 1131 usb_hcd_end_port_resume(&port->rhub->hcd->self, portnum); 1132 } 1133 port->rexit_active = 0; 1134 bus_state->suspended_ports &= ~(1 << portnum); 1135 } 1136 } 1137 1138 /* 1139 * Converts a raw xHCI port status into the format that external USB 2.0 or USB 1140 * 3.0 hubs use. 1141 * 1142 * Possible side effects: 1143 * - Mark a port as being done with device resume, 1144 * and ring the endpoint doorbells. 1145 * - Stop the Synopsys redriver Compliance Mode polling. 1146 * - Drop and reacquire the xHCI lock, in order to wait for port resume. 1147 */ 1148 static u32 xhci_get_port_status(struct usb_hcd *hcd, 1149 struct xhci_bus_state *bus_state, 1150 u16 wIndex, u32 raw_port_status, 1151 unsigned long *flags) 1152 __releases(&xhci->lock) 1153 __acquires(&xhci->lock) 1154 { 1155 u32 status = 0; 1156 struct xhci_hub *rhub; 1157 struct xhci_port *port; 1158 1159 rhub = xhci_get_rhub(hcd); 1160 port = rhub->ports[wIndex]; 1161 1162 /* common wPortChange bits */ 1163 if (raw_port_status & PORT_CSC) 1164 status |= USB_PORT_STAT_C_CONNECTION << 16; 1165 if (raw_port_status & PORT_PEC) 1166 status |= USB_PORT_STAT_C_ENABLE << 16; 1167 if ((raw_port_status & PORT_OCC)) 1168 status |= USB_PORT_STAT_C_OVERCURRENT << 16; 1169 if ((raw_port_status & PORT_RC)) 1170 status |= USB_PORT_STAT_C_RESET << 16; 1171 1172 /* common wPortStatus bits */ 1173 if (raw_port_status & PORT_CONNECT) { 1174 status |= USB_PORT_STAT_CONNECTION; 1175 status |= xhci_port_speed(raw_port_status); 1176 } 1177 if (raw_port_status & PORT_PE) 1178 status |= USB_PORT_STAT_ENABLE; 1179 if (raw_port_status & PORT_OC) 1180 status |= USB_PORT_STAT_OVERCURRENT; 1181 if (raw_port_status & PORT_RESET) 1182 status |= USB_PORT_STAT_RESET; 1183 1184 /* USB2 and USB3 specific bits, including Port Link State */ 1185 if (hcd->speed >= HCD_USB3) 1186 xhci_get_usb3_port_status(port, &status, raw_port_status); 1187 else 1188 xhci_get_usb2_port_status(port, &status, raw_port_status, 1189 flags); 1190 1191 if (bus_state->port_c_suspend & (1 << wIndex)) 1192 status |= USB_PORT_STAT_C_SUSPEND << 16; 1193 1194 return status; 1195 } 1196 1197 int xhci_hub_control(struct usb_hcd *hcd, u16 typeReq, u16 wValue, 1198 u16 wIndex, char *buf, u16 wLength) 1199 { 1200 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1201 int max_ports; 1202 unsigned long flags; 1203 u32 temp, status; 1204 int retval = 0; 1205 int slot_id; 1206 struct xhci_bus_state *bus_state; 1207 u16 link_state = 0; 1208 u16 wake_mask = 0; 1209 u16 timeout = 0; 1210 u16 test_mode = 0; 1211 struct xhci_hub *rhub; 1212 struct xhci_port **ports; 1213 struct xhci_port *port; 1214 int portnum1; 1215 1216 rhub = xhci_get_rhub(hcd); 1217 ports = rhub->ports; 1218 max_ports = rhub->num_ports; 1219 bus_state = &rhub->bus_state; 1220 portnum1 = wIndex & 0xff; 1221 1222 spin_lock_irqsave(&xhci->lock, flags); 1223 switch (typeReq) { 1224 case GetHubStatus: 1225 /* No power source, over-current reported per port */ 1226 memset(buf, 0, 4); 1227 break; 1228 case GetHubDescriptor: 1229 /* Check to make sure userspace is asking for the USB 3.0 hub 1230 * descriptor for the USB 3.0 roothub. If not, we stall the 1231 * endpoint, like external hubs do. 1232 */ 1233 if (hcd->speed >= HCD_USB3 && 1234 (wLength < USB_DT_SS_HUB_SIZE || 1235 wValue != (USB_DT_SS_HUB << 8))) { 1236 xhci_dbg(xhci, "Wrong hub descriptor type for " 1237 "USB 3.0 roothub.\n"); 1238 goto error; 1239 } 1240 xhci_hub_descriptor(hcd, xhci, 1241 (struct usb_hub_descriptor *) buf); 1242 break; 1243 case DeviceRequest | USB_REQ_GET_DESCRIPTOR: 1244 if ((wValue & 0xff00) != (USB_DT_BOS << 8)) 1245 goto error; 1246 1247 if (hcd->speed < HCD_USB3) 1248 goto error; 1249 1250 retval = xhci_create_usb3x_bos_desc(xhci, buf, wLength); 1251 spin_unlock_irqrestore(&xhci->lock, flags); 1252 return retval; 1253 case GetPortStatus: 1254 if (!portnum1 || portnum1 > max_ports) 1255 goto error; 1256 1257 wIndex--; 1258 port = ports[portnum1 - 1]; 1259 temp = readl(port->addr); 1260 if (temp == ~(u32)0) { 1261 xhci_hc_died(xhci); 1262 retval = -ENODEV; 1263 break; 1264 } 1265 trace_xhci_get_port_status(wIndex, temp); 1266 status = xhci_get_port_status(hcd, bus_state, wIndex, temp, 1267 &flags); 1268 if (status == 0xffffffff) 1269 goto error; 1270 1271 xhci_dbg(xhci, "Get port status %d-%d read: 0x%x, return 0x%x", 1272 hcd->self.busnum, portnum1, temp, status); 1273 1274 put_unaligned(cpu_to_le32(status), (__le32 *) buf); 1275 /* if USB 3.1 extended port status return additional 4 bytes */ 1276 if (wValue == 0x02) { 1277 u32 port_li; 1278 1279 if (hcd->speed < HCD_USB31 || wLength != 8) { 1280 xhci_err(xhci, "get ext port status invalid parameter\n"); 1281 retval = -EINVAL; 1282 break; 1283 } 1284 port_li = readl(port->addr + PORTLI); 1285 status = xhci_get_ext_port_status(temp, port_li); 1286 put_unaligned_le32(status, &buf[4]); 1287 } 1288 break; 1289 case SetPortFeature: 1290 if (wValue == USB_PORT_FEAT_LINK_STATE) 1291 link_state = (wIndex & 0xff00) >> 3; 1292 if (wValue == USB_PORT_FEAT_REMOTE_WAKE_MASK) 1293 wake_mask = wIndex & 0xff00; 1294 if (wValue == USB_PORT_FEAT_TEST) 1295 test_mode = (wIndex & 0xff00) >> 8; 1296 /* The MSB of wIndex is the U1/U2 timeout */ 1297 timeout = (wIndex & 0xff00) >> 8; 1298 1299 wIndex &= 0xff; 1300 if (!portnum1 || portnum1 > max_ports) 1301 goto error; 1302 1303 port = ports[portnum1 - 1]; 1304 wIndex--; 1305 temp = readl(port->addr); 1306 if (temp == ~(u32)0) { 1307 xhci_hc_died(xhci); 1308 retval = -ENODEV; 1309 break; 1310 } 1311 temp = xhci_port_state_to_neutral(temp); 1312 /* FIXME: What new port features do we need to support? */ 1313 switch (wValue) { 1314 case USB_PORT_FEAT_SUSPEND: 1315 temp = readl(port->addr); 1316 if ((temp & PORT_PLS_MASK) != XDEV_U0) { 1317 /* Resume the port to U0 first */ 1318 xhci_set_link_state(xhci, port, XDEV_U0); 1319 spin_unlock_irqrestore(&xhci->lock, flags); 1320 msleep(10); 1321 spin_lock_irqsave(&xhci->lock, flags); 1322 } 1323 /* In spec software should not attempt to suspend 1324 * a port unless the port reports that it is in the 1325 * enabled (PED = ‘1’,PLS < ‘3’) state. 1326 */ 1327 temp = readl(port->addr); 1328 if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) 1329 || (temp & PORT_PLS_MASK) >= XDEV_U3) { 1330 xhci_warn(xhci, "USB core suspending port %d-%d not in U0/U1/U2\n", 1331 hcd->self.busnum, portnum1); 1332 goto error; 1333 } 1334 1335 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1336 portnum1); 1337 if (!slot_id) { 1338 xhci_warn(xhci, "slot_id is zero\n"); 1339 goto error; 1340 } 1341 /* unlock to execute stop endpoint commands */ 1342 spin_unlock_irqrestore(&xhci->lock, flags); 1343 xhci_stop_device(xhci, slot_id, 1); 1344 spin_lock_irqsave(&xhci->lock, flags); 1345 1346 xhci_set_link_state(xhci, port, XDEV_U3); 1347 1348 spin_unlock_irqrestore(&xhci->lock, flags); 1349 msleep(10); /* wait device to enter */ 1350 spin_lock_irqsave(&xhci->lock, flags); 1351 1352 temp = readl(port->addr); 1353 bus_state->suspended_ports |= 1 << wIndex; 1354 break; 1355 case USB_PORT_FEAT_LINK_STATE: 1356 temp = readl(port->addr); 1357 /* Disable port */ 1358 if (link_state == USB_SS_PORT_LS_SS_DISABLED) { 1359 xhci_dbg(xhci, "Disable port %d-%d\n", 1360 hcd->self.busnum, portnum1); 1361 temp = xhci_port_state_to_neutral(temp); 1362 /* 1363 * Clear all change bits, so that we get a new 1364 * connection event. 1365 */ 1366 temp |= PORT_CSC | PORT_PEC | PORT_WRC | 1367 PORT_OCC | PORT_RC | PORT_PLC | 1368 PORT_CEC; 1369 writel(temp | PORT_PE, port->addr); 1370 temp = readl(port->addr); 1371 break; 1372 } 1373 1374 /* Put link in RxDetect (enable port) */ 1375 if (link_state == USB_SS_PORT_LS_RX_DETECT) { 1376 xhci_dbg(xhci, "Enable port %d-%d\n", 1377 hcd->self.busnum, portnum1); 1378 xhci_set_link_state(xhci, port, link_state); 1379 temp = readl(port->addr); 1380 break; 1381 } 1382 1383 /* 1384 * For xHCI 1.1 according to section 4.19.1.2.4.1 a 1385 * root hub port's transition to compliance mode upon 1386 * detecting LFPS timeout may be controlled by an 1387 * Compliance Transition Enabled (CTE) flag (not 1388 * software visible). This flag is set by writing 0xA 1389 * to PORTSC PLS field which will allow transition to 1390 * compliance mode the next time LFPS timeout is 1391 * encountered. A warm reset will clear it. 1392 * 1393 * The CTE flag is only supported if the HCCPARAMS2 CTC 1394 * flag is set, otherwise, the compliance substate is 1395 * automatically entered as on 1.0 and prior. 1396 */ 1397 if (link_state == USB_SS_PORT_LS_COMP_MOD) { 1398 if (!HCC2_CTC(xhci->hcc_params2)) { 1399 xhci_dbg(xhci, "CTC flag is 0, port already supports entering compliance mode\n"); 1400 break; 1401 } 1402 1403 if ((temp & PORT_CONNECT)) { 1404 xhci_warn(xhci, "Can't set compliance mode when port is connected\n"); 1405 goto error; 1406 } 1407 1408 xhci_dbg(xhci, "Enable compliance mode transition for port %d-%d\n", 1409 hcd->self.busnum, portnum1); 1410 xhci_set_link_state(xhci, port, link_state); 1411 1412 temp = readl(port->addr); 1413 break; 1414 } 1415 /* Port must be enabled */ 1416 if (!(temp & PORT_PE)) { 1417 retval = -ENODEV; 1418 break; 1419 } 1420 /* Can't set port link state above '3' (U3) */ 1421 if (link_state > USB_SS_PORT_LS_U3) { 1422 xhci_warn(xhci, "Cannot set port %d-%d link state %d\n", 1423 hcd->self.busnum, portnum1, link_state); 1424 goto error; 1425 } 1426 1427 /* 1428 * set link to U0, steps depend on current link state. 1429 * U3: set link to U0 and wait for u3exit completion. 1430 * U1/U2: no PLC complete event, only set link to U0. 1431 * Resume/Recovery: device initiated U0, only wait for 1432 * completion 1433 */ 1434 if (link_state == USB_SS_PORT_LS_U0) { 1435 u32 pls = temp & PORT_PLS_MASK; 1436 bool wait_u0 = false; 1437 1438 /* already in U0 */ 1439 if (pls == XDEV_U0) 1440 break; 1441 if (pls == XDEV_U3 || 1442 pls == XDEV_RESUME || 1443 pls == XDEV_RECOVERY) { 1444 wait_u0 = true; 1445 reinit_completion(&port->u3exit_done); 1446 } 1447 if (pls <= XDEV_U3) /* U1, U2, U3 */ 1448 xhci_set_link_state(xhci, port, USB_SS_PORT_LS_U0); 1449 if (!wait_u0) { 1450 if (pls > XDEV_U3) 1451 goto error; 1452 break; 1453 } 1454 spin_unlock_irqrestore(&xhci->lock, flags); 1455 if (!wait_for_completion_timeout(&port->u3exit_done, 1456 msecs_to_jiffies(500))) 1457 xhci_dbg(xhci, "missing U0 port change event for port %d-%d\n", 1458 hcd->self.busnum, portnum1); 1459 spin_lock_irqsave(&xhci->lock, flags); 1460 temp = readl(port->addr); 1461 break; 1462 } 1463 1464 if (link_state == USB_SS_PORT_LS_U3) { 1465 int retries = 16; 1466 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1467 portnum1); 1468 if (slot_id) { 1469 /* unlock to execute stop endpoint 1470 * commands */ 1471 spin_unlock_irqrestore(&xhci->lock, 1472 flags); 1473 xhci_stop_device(xhci, slot_id, 1); 1474 spin_lock_irqsave(&xhci->lock, flags); 1475 } 1476 xhci_set_link_state(xhci, port, USB_SS_PORT_LS_U3); 1477 spin_unlock_irqrestore(&xhci->lock, flags); 1478 while (retries--) { 1479 usleep_range(4000, 8000); 1480 temp = readl(port->addr); 1481 if ((temp & PORT_PLS_MASK) == XDEV_U3) 1482 break; 1483 } 1484 spin_lock_irqsave(&xhci->lock, flags); 1485 temp = readl(port->addr); 1486 bus_state->suspended_ports |= 1 << wIndex; 1487 } 1488 break; 1489 case USB_PORT_FEAT_POWER: 1490 /* 1491 * Turn on ports, even if there isn't per-port switching. 1492 * HC will report connect events even before this is set. 1493 * However, hub_wq will ignore the roothub events until 1494 * the roothub is registered. 1495 */ 1496 xhci_set_port_power(xhci, port, true, &flags); 1497 break; 1498 case USB_PORT_FEAT_RESET: 1499 temp = (temp | PORT_RESET); 1500 writel(temp, port->addr); 1501 1502 temp = readl(port->addr); 1503 xhci_dbg(xhci, "set port reset, actual port %d-%d status = 0x%x\n", 1504 hcd->self.busnum, portnum1, temp); 1505 break; 1506 case USB_PORT_FEAT_REMOTE_WAKE_MASK: 1507 xhci_set_remote_wake_mask(xhci, port, wake_mask); 1508 temp = readl(port->addr); 1509 xhci_dbg(xhci, "set port remote wake mask, actual port %d-%d status = 0x%x\n", 1510 hcd->self.busnum, portnum1, temp); 1511 break; 1512 case USB_PORT_FEAT_BH_PORT_RESET: 1513 temp |= PORT_WR; 1514 writel(temp, port->addr); 1515 temp = readl(port->addr); 1516 break; 1517 case USB_PORT_FEAT_U1_TIMEOUT: 1518 if (hcd->speed < HCD_USB3) 1519 goto error; 1520 temp = readl(port->addr + PORTPMSC); 1521 temp &= ~PORT_U1_TIMEOUT_MASK; 1522 temp |= PORT_U1_TIMEOUT(timeout); 1523 writel(temp, port->addr + PORTPMSC); 1524 break; 1525 case USB_PORT_FEAT_U2_TIMEOUT: 1526 if (hcd->speed < HCD_USB3) 1527 goto error; 1528 temp = readl(port->addr + PORTPMSC); 1529 temp &= ~PORT_U2_TIMEOUT_MASK; 1530 temp |= PORT_U2_TIMEOUT(timeout); 1531 writel(temp, port->addr + PORTPMSC); 1532 break; 1533 case USB_PORT_FEAT_TEST: 1534 /* 4.19.6 Port Test Modes (USB2 Test Mode) */ 1535 if (hcd->speed != HCD_USB2) 1536 goto error; 1537 if (test_mode > USB_TEST_FORCE_ENABLE || 1538 test_mode < USB_TEST_J) 1539 goto error; 1540 retval = xhci_enter_test_mode(xhci, test_mode, wIndex, 1541 &flags); 1542 break; 1543 default: 1544 goto error; 1545 } 1546 /* unblock any posted writes */ 1547 temp = readl(port->addr); 1548 break; 1549 case ClearPortFeature: 1550 if (!portnum1 || portnum1 > max_ports) 1551 goto error; 1552 1553 port = ports[portnum1 - 1]; 1554 1555 wIndex--; 1556 temp = readl(port->addr); 1557 if (temp == ~(u32)0) { 1558 xhci_hc_died(xhci); 1559 retval = -ENODEV; 1560 break; 1561 } 1562 /* FIXME: What new port features do we need to support? */ 1563 temp = xhci_port_state_to_neutral(temp); 1564 switch (wValue) { 1565 case USB_PORT_FEAT_SUSPEND: 1566 temp = readl(port->addr); 1567 xhci_dbg(xhci, "clear USB_PORT_FEAT_SUSPEND\n"); 1568 xhci_dbg(xhci, "PORTSC %04x\n", temp); 1569 if (temp & PORT_RESET) 1570 goto error; 1571 if ((temp & PORT_PLS_MASK) == XDEV_U3) { 1572 if ((temp & PORT_PE) == 0) 1573 goto error; 1574 1575 set_bit(wIndex, &bus_state->resuming_ports); 1576 usb_hcd_start_port_resume(&hcd->self, wIndex); 1577 xhci_set_link_state(xhci, port, XDEV_RESUME); 1578 spin_unlock_irqrestore(&xhci->lock, flags); 1579 msleep(USB_RESUME_TIMEOUT); 1580 spin_lock_irqsave(&xhci->lock, flags); 1581 xhci_set_link_state(xhci, port, XDEV_U0); 1582 clear_bit(wIndex, &bus_state->resuming_ports); 1583 usb_hcd_end_port_resume(&hcd->self, wIndex); 1584 } 1585 bus_state->port_c_suspend |= 1 << wIndex; 1586 1587 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1588 portnum1); 1589 if (!slot_id) { 1590 xhci_dbg(xhci, "slot_id is zero\n"); 1591 goto error; 1592 } 1593 xhci_ring_device(xhci, slot_id); 1594 break; 1595 case USB_PORT_FEAT_C_SUSPEND: 1596 bus_state->port_c_suspend &= ~(1 << wIndex); 1597 fallthrough; 1598 case USB_PORT_FEAT_C_RESET: 1599 case USB_PORT_FEAT_C_BH_PORT_RESET: 1600 case USB_PORT_FEAT_C_CONNECTION: 1601 case USB_PORT_FEAT_C_OVER_CURRENT: 1602 case USB_PORT_FEAT_C_ENABLE: 1603 case USB_PORT_FEAT_C_PORT_LINK_STATE: 1604 case USB_PORT_FEAT_C_PORT_CONFIG_ERROR: 1605 xhci_clear_port_change_bit(xhci, wValue, wIndex, 1606 port->addr, temp); 1607 break; 1608 case USB_PORT_FEAT_ENABLE: 1609 xhci_disable_port(xhci, port); 1610 break; 1611 case USB_PORT_FEAT_POWER: 1612 xhci_set_port_power(xhci, port, false, &flags); 1613 break; 1614 case USB_PORT_FEAT_TEST: 1615 retval = xhci_exit_test_mode(xhci); 1616 break; 1617 default: 1618 goto error; 1619 } 1620 break; 1621 default: 1622 error: 1623 /* "stall" on error */ 1624 retval = -EPIPE; 1625 } 1626 spin_unlock_irqrestore(&xhci->lock, flags); 1627 return retval; 1628 } 1629 EXPORT_SYMBOL_GPL(xhci_hub_control); 1630 1631 /* 1632 * Returns 0 if the status hasn't changed, or the number of bytes in buf. 1633 * Ports are 0-indexed from the HCD point of view, 1634 * and 1-indexed from the USB core pointer of view. 1635 * 1636 * Note that the status change bits will be cleared as soon as a port status 1637 * change event is generated, so we use the saved status from that event. 1638 */ 1639 int xhci_hub_status_data(struct usb_hcd *hcd, char *buf) 1640 { 1641 unsigned long flags; 1642 u32 temp, status; 1643 u32 mask; 1644 int i, retval; 1645 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1646 int max_ports; 1647 struct xhci_bus_state *bus_state; 1648 bool reset_change = false; 1649 struct xhci_hub *rhub; 1650 struct xhci_port **ports; 1651 1652 rhub = xhci_get_rhub(hcd); 1653 ports = rhub->ports; 1654 max_ports = rhub->num_ports; 1655 bus_state = &rhub->bus_state; 1656 1657 /* Initial status is no changes */ 1658 retval = (max_ports + 8) / 8; 1659 memset(buf, 0, retval); 1660 1661 /* 1662 * Inform the usbcore about resume-in-progress by returning 1663 * a non-zero value even if there are no status changes. 1664 */ 1665 spin_lock_irqsave(&xhci->lock, flags); 1666 1667 status = bus_state->resuming_ports; 1668 1669 /* 1670 * SS devices are only visible to roothub after link training completes. 1671 * Keep polling roothubs for a grace period after xHC start 1672 */ 1673 if (xhci->run_graceperiod) { 1674 if (time_before(jiffies, xhci->run_graceperiod)) 1675 status = 1; 1676 else 1677 xhci->run_graceperiod = 0; 1678 } 1679 1680 mask = PORT_CSC | PORT_PEC | PORT_OCC | PORT_PLC | PORT_WRC | PORT_CEC; 1681 1682 /* For each port, did anything change? If so, set that bit in buf. */ 1683 for (i = 0; i < max_ports; i++) { 1684 temp = readl(ports[i]->addr); 1685 if (temp == ~(u32)0) { 1686 xhci_hc_died(xhci); 1687 retval = -ENODEV; 1688 break; 1689 } 1690 trace_xhci_hub_status_data(i, temp); 1691 1692 if ((temp & mask) != 0 || 1693 (bus_state->port_c_suspend & 1 << i) || 1694 (ports[i]->resume_timestamp && time_after_eq( 1695 jiffies, ports[i]->resume_timestamp))) { 1696 buf[(i + 1) / 8] |= 1 << (i + 1) % 8; 1697 status = 1; 1698 } 1699 if ((temp & PORT_RC)) 1700 reset_change = true; 1701 if (temp & PORT_OC) 1702 status = 1; 1703 } 1704 if (!status && !reset_change) { 1705 xhci_dbg(xhci, "%s: stopping usb%d port polling\n", 1706 __func__, hcd->self.busnum); 1707 clear_bit(HCD_FLAG_POLL_RH, &hcd->flags); 1708 } 1709 spin_unlock_irqrestore(&xhci->lock, flags); 1710 return status ? retval : 0; 1711 } 1712 1713 #ifdef CONFIG_PM 1714 1715 int xhci_bus_suspend(struct usb_hcd *hcd) 1716 { 1717 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1718 int max_ports, port_index; 1719 struct xhci_bus_state *bus_state; 1720 unsigned long flags; 1721 struct xhci_hub *rhub; 1722 struct xhci_port **ports; 1723 u32 portsc_buf[USB_MAXCHILDREN]; 1724 bool wake_enabled; 1725 1726 rhub = xhci_get_rhub(hcd); 1727 ports = rhub->ports; 1728 max_ports = rhub->num_ports; 1729 bus_state = &rhub->bus_state; 1730 wake_enabled = hcd->self.root_hub->do_remote_wakeup; 1731 1732 spin_lock_irqsave(&xhci->lock, flags); 1733 1734 if (wake_enabled) { 1735 if (bus_state->resuming_ports || /* USB2 */ 1736 bus_state->port_remote_wakeup) { /* USB3 */ 1737 spin_unlock_irqrestore(&xhci->lock, flags); 1738 xhci_dbg(xhci, "usb%d bus suspend to fail because a port is resuming\n", 1739 hcd->self.busnum); 1740 return -EBUSY; 1741 } 1742 } 1743 /* 1744 * Prepare ports for suspend, but don't write anything before all ports 1745 * are checked and we know bus suspend can proceed 1746 */ 1747 bus_state->bus_suspended = 0; 1748 port_index = max_ports; 1749 while (port_index--) { 1750 u32 t1, t2; 1751 int retries = 10; 1752 retry: 1753 t1 = readl(ports[port_index]->addr); 1754 t2 = xhci_port_state_to_neutral(t1); 1755 portsc_buf[port_index] = 0; 1756 1757 /* 1758 * Give a USB3 port in link training time to finish, but don't 1759 * prevent suspend as port might be stuck 1760 */ 1761 if ((hcd->speed >= HCD_USB3) && retries-- && 1762 (t1 & PORT_PLS_MASK) == XDEV_POLLING) { 1763 spin_unlock_irqrestore(&xhci->lock, flags); 1764 msleep(XHCI_PORT_POLLING_LFPS_TIME); 1765 spin_lock_irqsave(&xhci->lock, flags); 1766 xhci_dbg(xhci, "port %d-%d polling in bus suspend, waiting\n", 1767 hcd->self.busnum, port_index + 1); 1768 goto retry; 1769 } 1770 /* bail out if port detected a over-current condition */ 1771 if (t1 & PORT_OC) { 1772 bus_state->bus_suspended = 0; 1773 spin_unlock_irqrestore(&xhci->lock, flags); 1774 xhci_dbg(xhci, "Bus suspend bailout, port over-current detected\n"); 1775 return -EBUSY; 1776 } 1777 /* suspend ports in U0, or bail out for new connect changes */ 1778 if ((t1 & PORT_PE) && (t1 & PORT_PLS_MASK) == XDEV_U0) { 1779 if ((t1 & PORT_CSC) && wake_enabled) { 1780 bus_state->bus_suspended = 0; 1781 spin_unlock_irqrestore(&xhci->lock, flags); 1782 xhci_dbg(xhci, "Bus suspend bailout, port connect change\n"); 1783 return -EBUSY; 1784 } 1785 xhci_dbg(xhci, "port %d-%d not suspended\n", 1786 hcd->self.busnum, port_index + 1); 1787 t2 &= ~PORT_PLS_MASK; 1788 t2 |= PORT_LINK_STROBE | XDEV_U3; 1789 set_bit(port_index, &bus_state->bus_suspended); 1790 } 1791 /* USB core sets remote wake mask for USB 3.0 hubs, 1792 * including the USB 3.0 roothub, but only if CONFIG_PM 1793 * is enabled, so also enable remote wake here. 1794 */ 1795 if (wake_enabled) { 1796 if (t1 & PORT_CONNECT) { 1797 t2 |= PORT_WKOC_E | PORT_WKDISC_E; 1798 t2 &= ~PORT_WKCONN_E; 1799 } else { 1800 t2 |= PORT_WKOC_E | PORT_WKCONN_E; 1801 t2 &= ~PORT_WKDISC_E; 1802 } 1803 1804 if ((xhci->quirks & XHCI_U2_DISABLE_WAKE) && 1805 (hcd->speed < HCD_USB3)) { 1806 if (usb_amd_pt_check_port(hcd->self.controller, 1807 port_index)) 1808 t2 &= ~PORT_WAKE_BITS; 1809 } 1810 } else 1811 t2 &= ~PORT_WAKE_BITS; 1812 1813 t1 = xhci_port_state_to_neutral(t1); 1814 if (t1 != t2) 1815 portsc_buf[port_index] = t2; 1816 } 1817 1818 /* write port settings, stopping and suspending ports if needed */ 1819 port_index = max_ports; 1820 while (port_index--) { 1821 if (!portsc_buf[port_index]) 1822 continue; 1823 if (test_bit(port_index, &bus_state->bus_suspended)) { 1824 int slot_id; 1825 1826 slot_id = xhci_find_slot_id_by_port(hcd, xhci, 1827 port_index + 1); 1828 if (slot_id) { 1829 spin_unlock_irqrestore(&xhci->lock, flags); 1830 xhci_stop_device(xhci, slot_id, 1); 1831 spin_lock_irqsave(&xhci->lock, flags); 1832 } 1833 } 1834 writel(portsc_buf[port_index], ports[port_index]->addr); 1835 } 1836 hcd->state = HC_STATE_SUSPENDED; 1837 bus_state->next_statechange = jiffies + msecs_to_jiffies(10); 1838 spin_unlock_irqrestore(&xhci->lock, flags); 1839 1840 if (bus_state->bus_suspended) 1841 usleep_range(5000, 10000); 1842 1843 return 0; 1844 } 1845 1846 /* 1847 * Workaround for missing Cold Attach Status (CAS) if device re-plugged in S3. 1848 * warm reset a USB3 device stuck in polling or compliance mode after resume. 1849 * See Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8 1850 */ 1851 static bool xhci_port_missing_cas_quirk(struct xhci_port *port) 1852 { 1853 u32 portsc; 1854 1855 portsc = readl(port->addr); 1856 1857 /* if any of these are set we are not stuck */ 1858 if (portsc & (PORT_CONNECT | PORT_CAS)) 1859 return false; 1860 1861 if (((portsc & PORT_PLS_MASK) != XDEV_POLLING) && 1862 ((portsc & PORT_PLS_MASK) != XDEV_COMP_MODE)) 1863 return false; 1864 1865 /* clear wakeup/change bits, and do a warm port reset */ 1866 portsc &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS); 1867 portsc |= PORT_WR; 1868 writel(portsc, port->addr); 1869 /* flush write */ 1870 readl(port->addr); 1871 return true; 1872 } 1873 1874 int xhci_bus_resume(struct usb_hcd *hcd) 1875 { 1876 struct xhci_hcd *xhci = hcd_to_xhci(hcd); 1877 struct xhci_bus_state *bus_state; 1878 unsigned long flags; 1879 int max_ports, port_index; 1880 int slot_id; 1881 int sret; 1882 u32 next_state; 1883 u32 temp, portsc; 1884 struct xhci_hub *rhub; 1885 struct xhci_port **ports; 1886 1887 rhub = xhci_get_rhub(hcd); 1888 ports = rhub->ports; 1889 max_ports = rhub->num_ports; 1890 bus_state = &rhub->bus_state; 1891 1892 if (time_before(jiffies, bus_state->next_statechange)) 1893 msleep(5); 1894 1895 spin_lock_irqsave(&xhci->lock, flags); 1896 if (!HCD_HW_ACCESSIBLE(hcd)) { 1897 spin_unlock_irqrestore(&xhci->lock, flags); 1898 return -ESHUTDOWN; 1899 } 1900 1901 /* delay the irqs */ 1902 temp = readl(&xhci->op_regs->command); 1903 temp &= ~CMD_EIE; 1904 writel(temp, &xhci->op_regs->command); 1905 1906 /* bus specific resume for ports we suspended at bus_suspend */ 1907 if (hcd->speed >= HCD_USB3) 1908 next_state = XDEV_U0; 1909 else 1910 next_state = XDEV_RESUME; 1911 1912 port_index = max_ports; 1913 while (port_index--) { 1914 portsc = readl(ports[port_index]->addr); 1915 1916 /* warm reset CAS limited ports stuck in polling/compliance */ 1917 if ((xhci->quirks & XHCI_MISSING_CAS) && 1918 (hcd->speed >= HCD_USB3) && 1919 xhci_port_missing_cas_quirk(ports[port_index])) { 1920 xhci_dbg(xhci, "reset stuck port %d-%d\n", 1921 hcd->self.busnum, port_index + 1); 1922 clear_bit(port_index, &bus_state->bus_suspended); 1923 continue; 1924 } 1925 /* resume if we suspended the link, and it is still suspended */ 1926 if (test_bit(port_index, &bus_state->bus_suspended)) 1927 switch (portsc & PORT_PLS_MASK) { 1928 case XDEV_U3: 1929 portsc = xhci_port_state_to_neutral(portsc); 1930 portsc &= ~PORT_PLS_MASK; 1931 portsc |= PORT_LINK_STROBE | next_state; 1932 break; 1933 case XDEV_RESUME: 1934 /* resume already initiated */ 1935 break; 1936 default: 1937 /* not in a resumeable state, ignore it */ 1938 clear_bit(port_index, 1939 &bus_state->bus_suspended); 1940 break; 1941 } 1942 /* disable wake for all ports, write new link state if needed */ 1943 portsc &= ~(PORT_RWC_BITS | PORT_CEC | PORT_WAKE_BITS); 1944 writel(portsc, ports[port_index]->addr); 1945 } 1946 1947 /* USB2 specific resume signaling delay and U0 link state transition */ 1948 if (hcd->speed < HCD_USB3) { 1949 if (bus_state->bus_suspended) { 1950 spin_unlock_irqrestore(&xhci->lock, flags); 1951 msleep(USB_RESUME_TIMEOUT); 1952 spin_lock_irqsave(&xhci->lock, flags); 1953 } 1954 for_each_set_bit(port_index, &bus_state->bus_suspended, 1955 BITS_PER_LONG) { 1956 /* Clear PLC to poll it later for U0 transition */ 1957 xhci_test_and_clear_bit(xhci, ports[port_index], 1958 PORT_PLC); 1959 xhci_set_link_state(xhci, ports[port_index], XDEV_U0); 1960 } 1961 } 1962 1963 /* poll for U0 link state complete, both USB2 and USB3 */ 1964 for_each_set_bit(port_index, &bus_state->bus_suspended, BITS_PER_LONG) { 1965 sret = xhci_handshake(ports[port_index]->addr, PORT_PLC, 1966 PORT_PLC, 10 * 1000); 1967 if (sret) { 1968 xhci_warn(xhci, "port %d-%d resume PLC timeout\n", 1969 hcd->self.busnum, port_index + 1); 1970 continue; 1971 } 1972 xhci_test_and_clear_bit(xhci, ports[port_index], PORT_PLC); 1973 slot_id = xhci_find_slot_id_by_port(hcd, xhci, port_index + 1); 1974 if (slot_id) 1975 xhci_ring_device(xhci, slot_id); 1976 } 1977 (void) readl(&xhci->op_regs->command); 1978 1979 bus_state->next_statechange = jiffies + msecs_to_jiffies(5); 1980 /* re-enable irqs */ 1981 temp = readl(&xhci->op_regs->command); 1982 temp |= CMD_EIE; 1983 writel(temp, &xhci->op_regs->command); 1984 temp = readl(&xhci->op_regs->command); 1985 1986 spin_unlock_irqrestore(&xhci->lock, flags); 1987 return 0; 1988 } 1989 1990 unsigned long xhci_get_resuming_ports(struct usb_hcd *hcd) 1991 { 1992 struct xhci_hub *rhub = xhci_get_rhub(hcd); 1993 1994 /* USB3 port wakeups are reported via usb_wakeup_notification() */ 1995 return rhub->bus_state.resuming_ports; /* USB2 ports only */ 1996 } 1997 1998 #endif /* CONFIG_PM */ 1999